Regulation 43, Indian Boiler Regulations, 1950: (a) Material
Indian Boiler Regulations, 1950 - Regulation 43
Text of regulation 43
(a) Material
43. (a) Material.—To comply with Regulation 36(a).
(b) Annealing.—The ondt- of all tubon shall be carefully annoaled to a length
not less than 0" if they have been submitted 1o a process of swelling or reducing
the end dimensions.
(c) Freedom from defects.—To comply with Regulation 36(c).
(d) Tolerances.—The tubes shall be of the dimensions spooifiod, straight, cylin-
drical, of uniform thickness and edema 1 diamol er i hroughout, subject to the working"
margins piveti in the table below:—
(i) Diameter.—The external diameter of the tubetj measured at any point shall
be within the following tolerances of diameter specified :•—-
OntmtU) d [lUnoter of tiibns.
Up to tirid including 2J in.
O v e r 24 i n . . . .
T o l e r a n c e .
^ 1 /04"
— 1 / 3 2 "
H 1 % -
(ii) Thickness.—Tho thickness of the tubes shall be within the following
toleranoen •- —
Outsido rlinintjter of tubes.
Up to ami moluding 2J in.
O^er 2} m
Tolerance
J 17*%
- 71%
^ io%
— 0%
Whero the ends of the tubes are swelled or reduced the thickness at the enda
may be decreased below or increased above the nominal thiokness of the tubes by
an amount in proportion to the percentage of aueh swelling or reduction and, in
addition to this allowance, the tolerances relating to thickness shall also apply.
(Jii) Length.—The tubos shall be not less than the nominal length but may
«xcccrl it by the amount given below :—
Up to and including 30 it.
Over 30 ft
1/8 in.
iH in.
(e) Selection of tubes for test.—To comply with Regulation 37.
44. (a) Tensile Test Tost pieces out from the ends of tho annealed portions
removed from tho ends of the selected tubes shall comply with tho folio-wing require-
ments :•—
— •
Strips cut from tubes und
tested in thoir curvod
condition.
Test lengths) tuken from
fliiishod tubas («nda ul
tubtiH to be plugged from
gripa).
Ultimate tunsile
utroHH ul tona por
HCJ. in.
Not loss
than
20
20
Not more
than
28
Minimum nlongution ptir rent.
on 8
1/4 in.
thick
and over
20
25
in.
Lena than
1 /4 in.
thick
18
23
on '2 in.
1/4 in.
thick
and over
,-JO
Leni thn,ii
1/4 in.
think
28
(b) Flattening Test-—A ring not less than 2 inches in length cut from the anneal-
ed portions removed from tin1 ends of the selected tuboH Hhn.ll be flattened between
two parallel flat surfaces, (he width of which shall be not less than ] J times tho
diameter of the tube. When the pressure is released, the interior surfaces of the test
piec,c at the middle shall remain at a distance apart of not more than three times tho
thickness of tho tube and 1 he test piece shall then show no sign of crack or flaw.
(o) Expanding Tests.- -The annealed tube ends shall wilhstand expanding by
a drift expander having a total included angle of between 40° and 60° (20° to 30°
per side) to the following increase in external diameter without showing truck or
flaw:—
Thieknoas ol Tube
°. S.W.O. mid thinner
Thinner than 5 S.W.G. und up to and including
3 8.W.G.
Thicker thun 3 S.W.O.
Increune in Diameter peT o«)it.
IB
12
0-fi
Previous and next
Questions people ask
Is regulation 43 of Indian Boiler Regulations, 1950 still in force?
No repeal of Indian Boiler Regulations, 1950 is recorded.