LawGrids logoLAWGRIDS.ORG

Regulation 198, Indian Boiler Regulations, 1950.: Flat tube plates

Indian Boiler Regulations, 1950. - Regulation 198

Text of regulation 198

Flat tube plates

198. Flat tube plates.—{a) For tho portions of tubo platow in the nests of tubes where stay tubes are required and where the minimum thickness and cross section of tube plate are not less than aw prescribed in Jiegulation 211 the maximum work- ing pressure shall be :— C(t-1)« W. P. = • Eqn. (33) P» P is the mean pitoh of the stay I ubes supporting any portion of the plate (being the sum of the four sides of tho quadrilateral divided by four). C => 70 for stay tubes sorowed and oxpanded into the plate and no nuts fitted. C ^ 85 for stay tubes screwed and expanded into the plate and fitted with nuts. (b) No ants shall be fitted to stay tubes at the combustion chamber or firebox end. (c) Where the platea are exposed to the direot impact of flame, the oo-efBoient O shall be reduced by 12J- per cent., and where the thickness or oross seotion Oi tube plate between tubes is leas than as piescribed in Regulation 2] 1 the appropriate oo-ofnoient shall bo reduced in proportion to the deficit. (d) For the wide water spaces of tube plates between the nests of tubes and between tho wing rows of tubes and the shell, tho maximum working prossure shall be:— C W. P. = — [(t_l)«+'65V] . . . . Eqn. (34) A«+B» A is the horizontal pitch of stay tubea in inohos measured across the wide water space from centre to centre, B is the vertical pitch of stay tubes in the bounding rows in inches measured from centre to centre, C •=• GO for stay tubea screwed and expanded into the tube plates and no nutn are fitted, 0 = 80 for stay tubes screwed and expanded into the tube platea and fitted with nuts, 0 •= 70 for stay tubes screwed and expanded into the tube platea ana nuts are fitted only to alternate stay tube, t is the thickness of tho flat pla*"o m 32nd1? of an inch, i1 is tho thickness of tho washci w, strips or doublings employed in 32nds of an iiwh. (e) Whore the plates aie exposed to the direct impact of flame, the co-efficient C shall be reduced 12J per cent. 196. Plates supported by gusset stays.—(a) For the end plates of Lancashire, Cornish, Vertical and Locotype boilers, and other flat surfaces supported by irregularly pitched gussot slays, the maximum working pressure shall he :-— C(t-1)» W. p. =, „ _ _ _ „ . . . . . . Eqn. (35) D« D IB the diameter in inches of the Lucent. oirele whioh can be drawn passing through not IBHK than throe points of Hiippf>rt, viz., the centre lines of rivets or the -commencement of the curvature of flanging, whichever is applicable. C = 100 for plates not exposed to flame. C a 88 for plates exposed to flame. (6) Where such plates are stiffened by suitable tee or angle bars securely riveted to tho plates within the circle D, tho appropriate co-efficient may be increased thirty per cent. Such stiffening bars shall be placed so as to transmit their load in a direct manner to the gusset stays or shell plate. (c) Foi the part of the end plate containing the manhole in Lancashire boilers "the maximum working pressure shall be :— WP^^Kt-ll '+fe-l)'] , . . . . Eqn. (36) D is the diameter in inohes of the largest circle which can be drawn enclosing the manhole and passing thiough the centres of the rivets in end plates connecting the shell and gusset angles and furnaces or to the commencement of curvature of flang- ing, whichever is applicable where the circle passes through only three of the possible five points of support mentioned the remaining two shall he embraced within the circle. t ife the thickness of thi end plates m 32nds of an inch, tx is the thickness of the base of the mouthpiece or flat ring in 32nds of an inoh, C c= 90 where the manhole mouthpiece is either of mild or cast steel, and has a turned-in flango of a depth, measured from inside of end plato, of not less than 4 times the thickness of the end plate, and thickness not less than tho thickness of the end plate, C =70 where only a fiat stcol < ompensatmg ling is fitted, C is to be taken aR tho moan of the points of support through whioh circle passes in accordant e with Regulation 19H where there iw no mouthpiece or flat ring and the end plate is flanged around the manhole to the depth required in Regulation 201. 197. Flat Crown plates ol vertical hollers.—(a) For the flat crown plates of vertical boilers either with or without bolt stays, Equation (35) shall be used in deter- mining the WOT king pressure wit h 0=80, when the plates are not exposed to flame, and 70 when thoy are exposed to flame. In this case T> ia the diaraetor of tho largest circle in inches that can be drawn passing through tho centres of tho rivets or bolt stays when fitted, or tho commencement of the ourvature of the flanging, whichever ig applicable. Where bolt stays are fitted with washers of tho same thickness as th« plate securely riveted thoreto, the cirole shall pass through the centres of the washer rivets but where the washors are not riveted or whore none are fitted the oirolo shall pass through the oontre of the stays. In the oasc of electrode boilers where the attach- ment of endfl is permitted by fillet welding as per Regulation 104(d), the working pressure shall be determined by Equation (35) with C=40. (b) Wliero the crown plate is flanged the inside radius of curvature at the flange shall not be less than 4 times the thickness of tho end plate, but in no case less than 2J". 198. Circular flat ends o! drums, etc., supported only at edges.—(a) 'For those ends C in Equation (35) shall be taken aa 140 whon the plates are not exposed to- flame, and 122-5 when they are exposed to flame. In this rase the circle D shall pass through the centres of rivets or bolts securing the end to the shell or, where- the end in flanged, through the commencement of ourvature. (b) Where flanged the inside radius of ourvature at the flange shall not be less than 4 times the thickness of the end plate but in no case less than 2|*.

Previous and next

All provisions of Indian Boiler Regulations, 1950.

Questions people ask

Is regulation 198 of Indian Boiler Regulations, 1950. still in force?

No repeal of Indian Boiler Regulations, 1950. is recorded.