LawGrids logoLAWGRIDS.ORG

Regulation 193, Indian Boiler Regulations, 1950.: Flat plates supported by solid screwed stays, marginal seams or flanges

Indian Boiler Regulations, 1950. - Regulation 193

Text of regulation 193

Flat plates supported by solid screwed stays, marginal seams or flanges

193. Flat plates supported by solid screwed stays, marginal seams or flanges.— (a) For plain flat pkton supported by solid screwed stays or riveted marginal seams- or fiances the maximum workins pleasure shall be as follows :— 0(t- l )« W.P. - — ^ _ Eqn. (28) A*-]-Ba In this foimulft and in those following in the succeeding regulations relating to "Flat Plates" unless otherwise specified. W. P. is the working pressure in lbs. per square inoh, t IB the thickness of the flat plate in 32nds of an inch, tx is I he thickness of the washers, strips, or doublings omployed, m 32nds of an inoh, A is the hoiizontal pitoh of stays in inohes, B in the vertical pitch of the Htaye in inches, C is a co-efficient whioh varies in valuo with the method of fixing the stays and nature of the support. Where the plates are exposed to the direct impaot of the flame the following values of C shall be reduced 12J per cent.— C = 60 for stays screwed into the plate with their ends riveted over. Sao. 81 THE GAZETTE OF INDIA j^l.riAOitDJLNAJKrjL C =s 90 for stays screwed into the plate and fitted with nuts on the outside, C =• 100 for stays passed through tho plate and fitted with nuts inside and out- aide, C = 110 for a riveted seam or flange, in the flat plate securing it to the shell side plate, end plate, furnace or uptake. Whero portions of plate are supported by stays or riveted seams or flanges having various values of support, the value of C, shall be taken as the mean of the points of support concerned. The support of a rivetod seam shall bo assumed to be at the line through the centres of rivets in the nearest row and of a flange at the commencement of curvature. In tho latter oase, if the inner radius of curvature of the flango exceeds 2^ times the thiokness of the plate, the support shall be assumed to be at a distance of 2\ times the thickness of the plate from the inner wide of the flange. (6) For portions of plate where the stays are irregularly pitched D ' shall be used instead of A ' + B ' , D being the diameter in inches of the largest oircle which can be drawn passing through not less than throe points of support, viz., the centres of stays, or rivets or the commencement of the curvature of flanging, whiohever is applicable. (c) For the tops and sides of combustion chambers and fireboxes tho distance between the rows of stays nearest to tho back tube late, or the back or firohole plate respectively, and the commencement of curvature of those plates at their flanges, shall not be greater than the maximum 7)itoh of the stays. (d) For the tops of combustion chambers and fireboxes where they are joined to the sides by curved portions, if the outer radius of tho curved portion i'i less than, half the allowable distance between the girders, the distance between the first girder and tho inner surface of tho side plates shall not exceed the allowable dis- tance between the girders. If the radius of curvature is greater than half the allow- able distance between the girders, the width of the flat portion measured from tho centre of the girder shall not be more than half the allowable distance between the girders. (e) Where stay tubes are not fitted in neat of tubes, as in tube plates of loco- fcype boilers, and parts of plate outside the spaoe occupied by tubes are supported, in aooordance with Regulation 212 (b), by ftcrowed stays each stay in the row noareBt the tubes shall bo sufficient strength to support the plate up to the edges of the tube holes in addition to its share of the plate on the opposite side of the line of stays. The working pressure for the plate between 1 ubos and stays shall be determined by Eqn. (28), A bcin^; the horizontal pitch of 1 ho stays in the nearost row, B twice the distance between the centre line of stays and a lino touching the tubes opposite them and C the co-efficient appropriate to the kind of stay.

Previous and next

All provisions of Indian Boiler Regulations, 1950.

Questions people ask

Is regulation 193 of Indian Boiler Regulations, 1950. still in force?

No repeal of Indian Boiler Regulations, 1950. is recorded.