LawGrids logoLAWGRIDS.ORG

Regulation 184, Indian Boiler Regulations, 1950.: Longitudinal Seams

Indian Boiler Regulations, 1950. - Regulation 184

Text of regulation 184

Longitudinal Seams

184. Longitudinal Seams.—The longitudinal seams of furnaces may be either: (a) Forgo Lap Welded. (b) Fusion Butt Welded, (o) Riveted. Longitudinal seams of furnaces exoeeding 3/8* thickness shall uot be riveted. 125. Fusion Welded Longitudinal Seams.—Where the longihidinal Keam is fusion welded tho following precautions shall be observed :— (a) Plates over 5/8 in. in tliicknosH shall be bevolled from both sides of oaoh abutting edgo, but the bevel need not necessarily be the same on each side (HPO Figs. 1 and 2). Plates less than 5/8 in. in Lhicknesa may be bevelled from ono aide only of eaoh abutting edge (soe Figs. 3 and 4). The included angle of the bevel shall be not less than 60° ,nnd the bevelling may be any one of tho forms shown in Figs. 1—4. Fig. 6. Fusion Welding oJ Gross Tubes ol Vertical Cross Tube Boilers. (b) In ordor to obtain full penetration of the weld metal a gap shall be main- talned between the plates when they are being welded. Joints shall be welded from both aides, and the dag shall be removed after making eaoh run. Before 044 THE GAZETTE OF INDIA EXTRAORDINARY [PART U the socond side of the joint is welded tuiy slag 01 defect at the bottom of the first) run shall be remoxed by grinding, chipping or machining. There shall be no appre- ciable undercutting of the plate. (c) Por the purpose of relieving internal stresses the plates adjacent to a fusion, •weld shall be efficiently annealed after welding, and when the firebox i« forge-welded! it should be allowed to cool gradually. 126. Furnace Crown.—(a) Tho furnace crown f.eum shall not fa 11 in line with any circumferential scam of the boiler shell. (b) the furau.ee crown nmy be riveted to tho vertical portion of tlic fijphox, or alternatively, the ioint nitty bo fusion hu1t welded by the electric are process, pro- vided the conditions, as to fusion welding in Regulation 125 are observed. Where the joint is to be welded the edges of tho furnace crown and the firebox body shall be bevelled in accordance with Tig. 3 or Fig. 4. The depth of tho flange of the furnace crown •plate from the commencement of tho curvature of the flanging radius shall be not lesi« than four times the plate thickness with a minimum of 1̂ inches. On completion of voiding the fiiebox nh&ll be effectively stress relieved by heat treatment (net JHO Ke^. 128.) 127. Cross Tubes.—(a) Cross tubes shall b< made from wckllesB .stoel tube or from plate or strip rolled and forgo water gas welded. Where welded tubes are used the longitudinal welds shall be so situated that they are not exposed to the direct impact of the flame. (b) The minimum thioknees shall be 5/16 in, (c) Where cross tubes are flanged and riveted to the furnaoe, the flanges shall bo set to the ourvature and taper of the furnace, and shall be a good fit before rivet- tog- (d) Where welded construction is employed the tubes shall be of sufficient length to enter the furnace plate and be flush with the water side all round or project not more than 6/8 in. into the water space at any part of the circumference. Where the tubes are fusion welded in position, the firebox plates shall be suitably ohamfored and the joints shall be welded externally and internally (see Fig. 5). 128. Uptakes.—(a) Tho uptakes shall be foimed from woldless., forge water gas welded or fusion butt welded steel tube and shall be securely riveted to the fur« nace crown plate and riveted to the shell crown plate. (b) As an alternative to riveting, the uptake may be fusion butt welded by the electric arc process to the upward flange of the opening in the fire box crown plate provided the conditions ajs to fusion welding in Regulation 125 are observed. The edges of the upward flange and the adjacent end of the uptake shall be bevelled in accordance with Fig. 3 or Fig. 4. The depth of the crown plate opening from the commencement of the ourvature of tho flanging radius shall be not less than twice the plate thickness with a minimum of 1 inch. On completion of welding the uptake and crown plate shall be effectively stress relieved by heat treatment. Where the firebox crown plate Is also fusion welded to the body of the fire- box, the firebox complete with uptake shall be effectively stress relieved by heat treatment on completion of the welding. (c) Welded uptakes shall be so arranged that tke weld is directly facing the longitudinal centre line of tbe manhole. 129. Loco Type Fireloxcs.—(n) The foundation M>sm whall be of rivetul con- atruction but all other seams may be welded subject to the depth of the flange being such that the welded seams fall between the 1st and 2nd rows of screwed «taye or between the flange and the adjacent row of sorewed stays. Sue. 8] THE GAZETTE OF INDIA EXTEAOBDINAEY 645 (b) The firohole mouthpiece may be similarly welded when the firebox and shell are flanged for the purpose. (o) The welding shall oomply with Regulation 125. STAYS 130. Bai Stays.—JSar staya shall not b<i w^Mod at any part. They Hhall pre. ferably have plus threads, the ends of the stays being upset or the middle portion being reduced for this purpose. Stay bars -which have been worked in the tire shall be subsequently annealed. 131. Longitudinal Stays.—(a) Longitudinal and nmnlai solid SUIVMI hta\s shall be efficiently secured with nuts at euch end and not merely riveted over. Where they are over 12 feet in length, they shall be supported at intervals of fl ft. along its length, (b) Where the stay is screwed through both platos, the stay and holes shall have a oontinnouB thread and fitted -with nuts and v, asheis on the outside. Whorn the stay passes through clearing holes tin internal nut and washer shall also be fitted. Where the stay is not normal to the surface of the plate the washers shall be shaped so as to form a true surface for the nuts or a knuckle joint may be fitted. (c) In vertical boilers the stays shall cither be screwed into both crown plates or screwed into the furnaco cro^vn plate and passed through clearing holes in the shell crown plate. 132. Nuts and Washers for Stays.- (a) The washers shall l>o at k-abi 2£ times the diameter of the threadod portion of the stay and not less than 1/4 in. in thick- ness, (b) The thickness of the external nuts Bhall be at least equal to the diameter of the threaded portion of the stay. Where bar stays pass through clearing holea in end plates, internal nuts of a thickness not less than two-thirds of the diameter of the threaded portion of the stay shall be fitted 133. Jointed Stays.—Wb^r« jonitod longitudinal sta^n .in hii(«i, 1 hoy shall, where practicable, be fitted with pins having an effective sectional area 25 per cent, in excess of that of the stay. If the pins are slack in the holes, the total slackness shall not be more than 1/10 inch. The pins shall be as close as possible to tho shoulder of the eye forging. The shoulder of the forging shall be at least 1/2 inch wide all round, i.e., the diameter at the shoulder shall be not less than the diameter of the hole plus I inch. 134. Diagonal bar or rod stays.—The sectional ar>>a of dia^om-l rod or bar stay shall boar the same proportion to that of a direct stay as the length of the dia- gonal stay bears to the length of the perpendicular line from the end of the diagonal stay to the surface supported. Tho ends of diagonal stays, shall not bo bent, but shall be attached to the plate -with bevelled washers and nuts or -with riveted tee, blocks or angles and shackle pins (see Regulation 133 for eyes and pins). SOBHWED STATS 136. Screwed Stays.-—(a) Screwed atayw and tho holes for these shall be sorewed with a continuous thread. (b) The screwed threads of the stay shall be clean, free from cheoks or imper- fections, of full depth, correot Whitworth form and a good fit in the holes. The middle portion shall preferably be turned down to the bottom of the thread. (o) The stays shall be screwed with fine threads of not less than 11 threads per inch. 646 THE GAZETTE OF INDIA EXTRAORDINARY [PABT II (d) The diameter of the stay over the threads shall not be less than 3/4 in. or twioe the thickness of the firebox plate whiohever is the greater. (e) The pitch of the stays at the furnaoe of vertioal boilers shall not exceed 14 times the thickness of the furnace plate. (f) Whero tho stays arc not fitted with nuts, the ends shall be riveted over to form substantial heads. (m) Crown stays of Looo Type boilers shall either be fitted with nuts or riveted over on the fire aide. 136. Axial drilling.- AH snowed .stays less than 14 in. long should pr̂ tVuably be drilled with a tell-tale holo 3/16 in. diameter to a depth of 1/2 in. beyond the innor face of tho plate. Stays whioh are obsouro on one side should preferably be made from hollow staybar. 137. Stay nuts.- (a) NuH IO W ' W stays in combustion chumlxis and lireboxos shall not bo less than 3/4 inch thick for stays up to 1^ inches diameter over threado, 7/8 inoh thiok for 1-5/8 inohes and If inches stays, 1 inch thick for 1-7/8 and 2 inohes stays, and 1-1/8 inches thiok for stays over 2 inohes in diameter. (b) The nuts shall be made of solid mild steel or of iron whioh shall be without weld if exposed to flame. 138. Spacing of end stays—Allowance lor curves, etc.—lYu tht> top* of fireboxes and combustion ohambors the distance between the rows of stays nearest to the tube plate or lirehol© plate or bade plate as the oase may bo, and the oommenoe- meafc of curvature of these plates at their flanges shall not be greater than the hori- zontal pitch of the stays. GIB DEB STAYS 139. (Jiider Stays for Firebox and combustion Chamber Crowns.—(.) FM H yrdf*1 when of the normal type, fitted with stay bolts and nuts, shall bo of the double plate interconnected type of sufficient strength to support its proportion of the load on the crown plate independently of tho crown plate. (b) Tho clear waterway between the crown plate and the underside of uhe girdor bars shall be as large as practicable but in no oase less than 1-1/2 inches aa in fig. 7. (c) The ends of the girders shall not rest on the landing of the flat crown plate but shall be oarefully fitted to bed direotly on the bends of the oorners of the vertical •end or sido plates. (d) The toes of the girders shall bo solid with the girder plates and not separate pieoes attached thereto. (e) Girders shall be properly attached to the crown plate by bolts or sorewe. NOTM.—Alternative methods of staying may be used, or unstayed firebox, crowns of special or patented design of equivalent strength may be fitted. See Regulations 230, 231 and 232. (f) Where an all welded firobox is fitted, the girder stays may be welded to the firebox prior to stress relieving. The girder stays shall be reoessed for waterways as in paragraph (h) (Figs. 6 and 7). Suoh girders shall be securely welded by an approved method to the firebox crown. The method of welding and the proportions of attachment shall be to the satisfaction of the Inspecting Authority. flWJ. 8] THE GAZETTE OF. INDIA EXTBAORl>INAft¥ 647 Pig. 6 Fig. 7 GDSSHT STA.YS 140. Gusset Stays.—(») Gusrot plates hhall bo flat and perpmidioular to the •end platoa. The gusset anglos shall be fitted to bed closely to the shell end and gussot plates. Cranking or setting of the plates is prohibited. (b) Gusset stays, where fitted, shall comprise flat plates seoured by double angle* to the shell and ond plato respectively, and shall be designed in accordance with the following conditions:— 1 4 1 . B r e a t h i n g S p a c e . — • ( a ) G u s s e t s t a y s s h a l l l i e H O a r r a n g e d a s i o a l l o w s u f f i c i e n t "breathing space around furnace connections and tube nests. (b) For Lancashire boilors the proportions shown in the table below are re- commended for the portion of the end plates above the furnaces and flues : TbickiiGBB of ond plates in. 1/2 ft/16 6/8 11/18 "I 3/4 I 13/10 J Above 13/16 L=. U'ig- 3) in. 9 10 11 12 124 L = (Pip. 0} hi. 10 i i 12 13 131 648 THE GAZETTE OF INDIA EXTRAOEDINAHY [PABT I I Fig. 8 Fig 9 (c) Fig. 8 shows the breathing space recommended for the following condi- tions : Flat end, furnace or flues flanged for attachment to end plato, furnaces and? flues formed with Adaroson flanged seams, (d) Fig. 9 shows similar conditions to Fig. 8 except that the end plate is flanged outwards for tho furnace or flue ring connection, the breathing spaces allowed being 1 in. more than those for the same thickness of pl&te in Fig. 8. (e) Where a corrugated section not less than 6 feet long is included in eaoh internal flue of a Lancashire boiler, the dimensions given in the table above may- be reduced by approximately 1J in. throughout. (f) It is recommended that the breathing space below the furnaces and fluer shall be approximately one half the dimensions given in the table above. Where it is desired to use any other arrangement which gives a greater or less degree of exibility, the amount of breathing spaoc shall be specially considered and modified as the neoesaity of the case requires. (g) For gusset stays above tube nests, as fitted in waste heat boilers without internal furnaces, a breathing space of 8 inches from the centre lino of the top tubes to the centre of the too rivets of the gusset angles is recommended (see Fig. 9). 142. Gussets /ngles.—The gusset angle connecting the htajR to tho shell and end plates shall be at least 7/8ths of the thickness of the shell plate, but shall be not loss than 1/2 in. in thickness 143. Load on Gusset Stay.--Each guwet stay supporting the Mid plate of a boiler shall be designed to carry the whole load due to pressure on the area supported by it. 144. Gusset Riveting-(a) Hivel- securing gusset staj« shall be not Jess in diameter than the thickness of the cylindrical shell plate and the rivetmg shall be arranged so that the strength of the sheU plate where drilled for the gueaet rivet* shall not be less than the strength of the longitudinal seams, (b) Not less than three rivets shall be used to connect any gusset plate to any angle or any angle to the end plate or to the shell plate. BOILER TUBES SUBJECT TO EXTERNAL PRESSURE 14ft. Steel and Wrought Iron Tubes.— (a) Both plain and utaj smoke tubes may be made either of wrought iron or steel and may be either lapwelded or weldlesfl. (b) Tubes may also be fabricated by electric resistance welding from strip plate. This may be aooepted for temperatures up to 7TO0F and presmireB up to 840 lbs./sq. in. 146 Fitting Plain Ttltoes.—Wheie stay tubeN arc not fitted, the ends of the tubes shall be beaded over at the fire box end and beaded or bell-mouthed at the other end. If bell-mouthed the tubes shall protrude not less than £ inch beyond! the tube plate. SHO. 8] THE GAZETTE OF INDIA EXTRAORDINARY 649" 147. Screw Threads ot stay tubes.—St»y tub< N shall be screwed at both ends with continuous threads, and the holes in tho tubo plates shall be tapped with continuous threads. Tho pitch of the threads shall not be finer than 11 threads- per inch. The stay tubes Bhall bo expanded by roller expanders and not made tight by oaulking only. 148. Minimum thickness ot stay tubes.—The minimum thiekneSH of «tHy tubes in the body or at the ends under threads shall not be less than 5/32nds of an inch. 149. Thickened ends oistay tubes.—If ntay uibob are required to hav<> their thickness increased at the screwed ends so that the thickness at the bottom of the threads is approximately tho same as in tho body of the tube tho thickening shall be attained by upsetting and not am7 welding process, and the tubes shall be an- nealed after the upsetting. 150. Load on stay tubes, (a) Staj tub^s ^hall bo di-signwl to ctiny tho whole- load due to pressure on the area to be supported In eaoh case the areas to be cal- culated as follows :—• (b) For a stay tube within the tube nest the net area to be supported shall be the produot of the horizontal and vertical pitches of the stay tube less the area of the tubo holes embraced. Where the pitch of the stay tube is irregular tho area shall be taken as tho square of the mean pitch of the stay tubes (i.e., one-quarter the sum of four sides of any quadrilateral bounded by four adjacent stay tubes) leas tho area of the tube holes embraced, (o) For a stay tube in the boundary row, the net area to be supported shall b& the area enclosed* by lines passing midway between it and the adjacent points of support less the area of any tubes embraced. Tho adjacent points of support may be ofther stay tubes, or tho commencement of curvature of flanging of centre line- of the circle of rivets securing tho end plate to tho shell angle, BOILER AND SUPERHEATER TUBES SUBJECT TO INTERNAL PRESSURE 151. Steel Tubes.— (a) All tubi-ft which aib subject to inti ma] pressure of water or steam shall bo cold drawn or hot finished seamless in accordance with Regula- tions 30 to 56. Except as pro\ided for in sub-reg. (6) below they shall be without joint. (b) Tubes having an external diameter not exceeding 5 inches may be jointed and such joints may be flash welded, machine forge welded, aro or gas welded. (c) Flash welding shall be undertaken on a welding machine of a type approved) by the Inspecting Officer and the external fin caused by welding shall be completely removed. The internal fin caused by welding ahall also be removed subjeot to a maximum height of 20 per cent, of tho wall thickness of the tube. (d) Aro welded butt joints shall be made by the metallio shielded aro- process. (e) When gan welding is employed the technique followed shall be approved) by an Inspecting Officer and all welds shall be suitably heat treated. (f) For design steam temperatures over 850cF the material to bo used shall be in accordance with Regs. 48 & 63. 152. Attachment ot steel tubes.—(a) Tubtw nhall be connected to the tub©= plates by one of the following methods :— (1) Expanding. (2) Strength welding. (3) Mechanioal bolted ball joint. 680 THE GAZETTE OF INDIA EXTBAOEDINABY [PABT I I (b) Drift or roller expanded tubes shall projeot through the neok or bearing •port in the holes by at least a quarter of an inoh and shall be seoured from drawing •out by being bell mouthed to the extent of 1/32" for each inoh in diameter plus 2/32". (o) Tubes may be seal welded into fittings or headers for both boilers and superheaters after they have been expanded and flared provided the material in the fittings or headers does not contain carbon in excess of 0 '35 per cent. (d) In the case of drifted or roller expanded tubes, the tube holes in tho tubes plates of drums, pockets, or headers shall be formed in such a way that the tubes oan be effectively tightened in them. Where the tube ends are not normal to •the tube plate, there shall be a neok or belt of parallel seating of at least 1/2" in depth measured in a piano normal to the axis of the tube at the holos. (e) Whore the tubes are strength welded direot to the tube plates, the technique followed shall be approved hy the Inspecting Authority and all welds shall be suitably heat treated. (f) Tube spacers, supporting olipM and lugs may bo welded to the tubes. Flash welding of studs for supporting refractories, etc., is also permissible. (g) The tubes shall be so arranged that they aro accessible for cleaning internally and externally. 153. Copper tubes.—Copp <r tub< s up to one inch in external diameter may bf> used for small boilers ; 'such tubes shall be not leas than 12 s.w.g. thiok. HEADERS, MUD BOXES, ETC., OF WATER TUBUS BOILERS 164. (<i) Hoadwb, mud boxot, i re., of water tube boilors may be of solid drawn or welded steel, or of cast steel complying with the requirements of Regulations 73 to 80. (!)) Each piece prior to being fitted in place shall be subjected to hydraulic teat to double the working pressure of the boiler into which it is to be fitted. For pressures over 1000 lbs. per sq. inoh, tho hydraulio teat pressure shall bo the permissible working pressure plus 1000 lbs. per sq. inoh. (c) (i) the sighting hole doors shall bo substantial and oapable of being removed and replaced from timo to time without loss of efficiency or safety. (ii) Tho bolts by which they are held in place shall be fitted to thorn in auoh a way as to satisfy the above conditions. (in) The doors shall be so designed that they will not blow out in the event •of breakage of the bolt. (iv) Circular holes also may be provided in addition to elliptical holes, if pro- vision is made to prevent the door boltw from turning, while securing tho joint. (d) All flanges shall have a fillet with a radius of curvature at least equal to the •thickness of the necks to which they are attached. STAND PIPES, PADS, ETC. 165. Stand Pipes and Pads.- -Stand pip«n and coatings for carrying mountings •shall be made of wrought, cast or fabrioatc-d steel. Where pipes are fabricated •by welding they shall be stress relieved. These shall tako the form of short ataud pipes, pressed steel plate saddles, forged pads or pads cut from round rolled l>ar as may be most convenient and seoured to the boiler by rivoting or welding. Where short stand pipes are used they shall bo of solid forged, fabricated or oast steel. They •«hall be carefully bedded to the shell before attachment and where riveted the rivets shall be so pitched as to ensure a tight joint. The jointing faces to whioh •mountings are to be bolted shall be machined. Pads shall have sufficient thiokneflB to allow the drilling of stud holes for mountings without the inner surface being pierced and the length of the screwed portion of the stud in the pad shall be not less than the diameter of the stud. 156. Design of Stand Pipes.—Whwo short Htand j>ipi-is are used, th« bolting flanges shall be forged solid with the bodios or attached by combined screwing and welding or by welding alone. The thickness of the stand pipes shall comply with table below:— Stand pipes In bore 3/4 . 1 . . . li . 11 . <2 2i . ,-; . 34 . 4- . H . . . 0 . 7 8 . 0 . 10 . Pressed saddles Mtii-iinum pfrmjcmblfi working prosHurnB lbs. per eq. in. TJpto ISO l('lango adjoin- ing drum in 7/16 7/lfi 7/10 7/lfi 7/10 9/1 fi fl/18 9/10 9/10 5/S 5/8 0/8 5/8 5/8 B/8 B/8 rhickiiosm oT B orly in 3/8 3/h 3/K 3/S 3/H 7/J0 7/10 7/10 7/16 9/16 9/10 9/16 9/10 B/8 5/8 Above1B0 & upto 250 ''lfltiRO adjoin- ing drum in 1/2 1/2 1/2 9/10 9/10 5/K 3/S 5/S fi/S 3/4 3/1 3/4 3/4 3/4 3/4 3/4 Thi. k- npea ol Body in 3/rt 3/ft 7,1(1 7/16 7/10 1,2 1/2 1/2 1/2 .T)/^ r>'8 C'S o i S 5/8 ff/8 A b n v e 2B0 & u p t o 3H0 Flnnge adjoin- ing drum i n 3/4 3/4 3/4 3-4 7/8 7/S 7/8 7/S 7/tt 7/S 7/8 7/8 7,8 7/8 7/S 7/8 Thiok- nesa of Body in 3/S 3/8 1/2 1/2 fi/S «/•, 8/8 B/8 fi/8 5/S 5/8 5/8 8,8 s/s Above 3C0 ifc upto 600 Flange adjoin- ing in 3/* 3/4 3/4 3/4 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 Th nk- negB of Body in. 3/8 3/8 3/8 ] / a 1/2 5/8 5/8 5/S 5/8 5/8 5/8 5/8 fi/8 5/8 167. Pressed Plate Saddles.—Where prewsod plato saddles ar« employed thpy shall be formed to bed olosely to the boiler, and be machined on the faoe jointing the mounting and on the edges. The studs for the attachment of mountings, if- Borewed through the saddle, shall eaoh be fitted with a nut on the inside having a. •thickness equal to the diameter of the stud. Where the stud holes do not penetrate 'through the saddle, the length of the screwed portion of the stud in the plate shall not ho less than the diameter of the stud. 168. Seatings tor Mountings.—For prcwRuros not njroef>ding 125 lbs. per nq, in. mountings with sorewed ends not exceeding 1 in. B.S.P.T. may be used; the sorewed portion of any such mounting being an integral part thereof and the thickness at rthe bottom of the thread being not less than 3/16". The mountings may be screwed :— (a) Directly into the boiler shell plate, nuts being fitted on the waterside, or (b) Into steel distance pieces the length of thread engaged being in no case less than the bore of the mounting plus 1/4 in. 159. Attachment ot Mountings.—(a) Mounting mny bn u11pchcd direct 'y u> any 'shell or end plate whero tho plate is of sufficient thickness to allow a suitable surface to be obtained for the attachment of the boiler mountings. (6) The minimum thickness at the hole in the shell or end plate shall bo not less than the thickness required for the maximum permissible working pressure considering the plate as being unpieroed. (c) Where the boiler mountings arc secured by studs, the studs shall have a full 'thread holding in the plate for at least one diameter. If the stud holes penetrate the whole thickness of the plate, the stud shall be screwed right through the plate and be fitted with a nut inside having a thickness equal to the diameter of the stud. Where bolts are used for securing mountings they shall be screwed right through 'the plate with their heads inside the shell or end plate. 160. Insufficient thickness of End Plates.—(u) In cases whero the thiokntF.i» of the end plate is insufficient for tills purpose the mountings shall be jointed to suitable steel soatings as provided in Regulation 155. (b) The following construction!* as to stand pipes attached to end plates shall be {permissible:-— (i) Where the internal diameter of the stand pipe does not exoecd 1 inch, the standpipe may be screwed into the plate and fitted with a nut on the waterside. (iiy Where the internal diameter of the standpipe exceeds 1 inoh but does not exoeod 2 incites, it may bo screwed in and seal-welded. ,(m) Where the diameter of the stundpipe exceeds 2 inches, it may bo welded to the end plate. The foregoing provisions as to the sfcandpipe shall be regulated by the following conditions. (iv) When standpipes are screwed, the screwing shall be British or American Standard Pipe Thread. i(v) Where standpipes, saddles or other forms of seatings are fabricated by fusion welding they shall bo stress relieved by heat treatment before attachment to the boiler. (vl) Where the boro of the standpipe or seating and the hole in the plate does not exceed 5 inches plus twice the thickness of the plate, the seating may be welded to the plate without subsequent heat troatment of the weld so made. Whero the hole in tho plate exceeds 5 inches plus twice the thickness of the plate, the plate to which the seating is attached shall be stress relieved by heat treatment. 161. Attachment oi Water and Pressure Gauges.—Water gauges and pressure ^gauge syphons may be attached direct to the front end plates without the inter- vention of a pad or standpipe, provided they are flanged and secured by studs If the studs are sorewed through the plate, nuts shall be fitted on the inside of the plate. 162. Mountings on Flat Plates.— -Where the flanged mountings are attached •direot to a flat plate, suoh mountings shall be provided •with a substantial spigot, the fall thickness of the boiler plate. 163. Bolts and Nuts.—Bolts and nuts shall b > machined where th°>y oorao in contact with the flanges, and all holes in saddles and pads shall be drilled. NOTE:—-In all oasos where the boiler 1a lagged, the joint of tho mountings shall be ulont of the lagging surfaoe or the lagging kept olear of the flangff so that tho joint oan be inipeuted and, when neoeaaary, remade. MANHOLES, MUDHOLtiS, ETC. 164. Access.—(a) Sufficient sight and oleaning holos ahall bo provided to permit of efficient inspection and cleaning. Such holos shall normally be elliptical in forrt} «.nd not loss than 3$ in. x - J in.* (b) At least one manhole or sight hole shall be provided in the uppor part of the cylindrical shell or in the shell orown, or end plate and this shall not bo IPSB than:— Boilers not exceeding 2 ft. 6 in. . Boilora over 2 ft. 6 in. diameter and not exceeding 3 ft. Boilorei over 3 ft. diameter and not exoeeding 3ft. 8 in. Boilers over 3 ft. 8 in. diameter and not excoading 4 ft. Boilers over 4 ft. . m. 0X7 12X9 14x10 15x11 16,- 12 (o) Where the size or construction of the boiler does not pormit of entry for oleaning and inspection sufficient oleaning holes shall be provided in the shell for these purposes. (d) Where cross tubes arc fitted in Vertical boilers one cleaning hole shall be pro- vided opposite at least one end of each tube. At the bottom of tho narrow water •spuces at least three cleaning holes shall be provided. The oleaning holes shall be •so arranged that the circumferential distanoe hotwoon them does not exceed 3 ft. sunless tho foundation xing is sufficiently aoctwsible to permit of cleaning and ins- pection from the inside of the boiler. (e) Cleaning holes or mudholes in Loco Type boilers shall be providod at each 'bottom corner of the outer firebox casing, above the fire hole ting and on each side •of saddle plate in line with bottom of barrel. (f) In the case of small boilers or where the foregoing provisions are impraft.j- •oablo the cleaning holes or mudholoa shall bo as nearly as p>>-nibb in tho corner of the outer firebox casing and tho holos as largo as circumstances permit. 165. Compensating Rings and Frames lor Opanings in Shells .—(a) Compen- sating rings and frames for openings in shells shall ne of wiought ot cast steel. 'The compensation provided shall preferably be flan^vl frames which H1IH.II be fitted in all cases whore tho shell plate eiooeds 9/16in. thick. Flanged frames shall bo w^ldless and shall be flanged or pressod to provide a H ii ioin'i.is; finr.n'" for the ^over. NOTE.—Wherever practicable the frames Hhould bu secured to the maido of the shells so Ahat the shorter axia is parallel to the longitudinal oontro lino of the boiler. • N O T E . — S t a n d a r d s i i e s o f m u d h o l e s a n d s i g h t h o l e a a r e T x 0 " , 6 " x 3 J * a n d 3 J * x 2 J ' . (b) All compenBating rings and frames shall be formed to bed closely to the Bur* faces to be connected. Where attached to cylindrical shells ana arc 12 in. x 9 in, or larger they shall be at least double riveted. AH caulking edges shall be maohined or machine gas cut. (c) The flat jointing surfaces of till flanged t r pressed frames and all doors or covers shall be machined. 166. Doors and Cross Bars.—(a) All internally fitted doois of manholes, mud- holes and sightholes shall be oi wrought steel built up or pi esscd to si wipe and anneal- ed or made from one thickness of plate with a machined recess for 1 he jointing material or may be a steel casting. Their spigot part or the reees,s shall not have u, groater olearance than 1/]ftlh inch all round, i.e., the axis .shall noi be le:,s than l/8th inch smaller than the holes in which they arc fitted. (b) The studs or bolt i of large doors shall be screwed through the plates and riveted over. (o) Internal doora for openings not larger than 9 in. x7 in. in size need only be fitted with one stud, which shall be piovided with an integral collar and screwed through the plate with a mil on the inside of the dooi. Internal doors for openings not largi i than 6 in. X 3-J in, may have the stud forged solid with the door or if screwed 'ie efficiently riveted to the doors. (d) Cross bars shall be of substantial proportions and either solid steel forging or of ci*st steel. 167. Raised Manhole frames and Cover plates.- (a) Raised circular manhole frames no1 < xcmling 10 inches in diameter shall be a1 l^ast 3/4 inches thick in, all parts. The ciroulai cover plates and joint flanges for such frames shall he not less than: 1 inch t'nck for pressures not exceeding 120 lb. sq. inch. 1-1/8 inch thick for pressures over 120 lb. but not exoeeding 200 lb. sq. inch. 1-1/4 inch thiok for pressures over 200 lb. but not exceeding 250 lb. sq. inch. For pressures 250 lb. sq. inch and over raised circular manhole frames shall not "be fitted. The cover plates shall be seemed by at least sixteen steel bolts not less than 1 inch diameter. (b) External raised ciroular mouthpieces shall be :-— (1) formed in one piece without welds, (2) formed fr om a suitable rolled section and forge welded, or (3) fabricated by fusion welding provided they are stress relieved by heat treatment after weldimr and before attaching to the boiler. Wolds should be positioned so that they are located on the transverse centre line of the boiler. The jointing flanges of mouthpieces and covers shall be machined on the face and edge and on the beat ing surface for the bolts. Bolts and nuts shall be mad lined where in contact with the flanges and tho joints should be formed inside and outside tho bolts to preclude tho possibility of flange distortion. Cover plates shaJl be dished outwards to a depth of approximately one-eight of the internal diameter ol the frame. All frames and mouthpieces shall bed olosely to the surfaces to which thoyjjare- to be connected, and where riveted to cylindrical shells shall be at least double riveted. All Caulking edges shall be machined or machine gas cut. €BO. 8] THE GAZETTE OF INDIA. EXTRAORDINARY 6K6 168. Position of Manhole in Shell.— Manholes in oylindrioal sholls rthall be placed is far as possible from any riveted seams, preferably towards the hack end of the boiler top. 169. Compensation Rings to Manholes, (a.) Compensation shall U- piovided" in every case for tho part ont out of a cylindrical shell for a manhole. The strength -of the net section of compensating rin<_' and of the rivets securing it to shell compared with that of tho part of shell cut out shall not bo loss than the st length of tho longi- tudinal scams. (b) The spacing of the rivets shall be such as not to reduce t,he -itretigth of the shell plate below that of the longitudinal seams. 170. Compensation lor cutting large holes in shell Type Boilers. - Where holes are cut in the cylindrical shell for the purpose of attaching a .seating, fritrno or door, compensation shall be provided such that tho added sectional area, including parts of the frame within 4 inches of fho shell and excluding rivet holes, shall be not. less than the sectional area of the plate removed whioh shall be the product of the dia- meter of the opening and the calculated thickness of the plate us found by Equa- tion I. Where holes are cut in tho cylindrical shell for the purpose of fixing seating for mountings and the diameter of the holes is greater than 2-1/2 times tlio thickness of the shell plate plus 2-3/4 inches, compensation shall be provided. Whore a large opening is cut in a cylindrical shell to receive another part of the structure, the sides where cut away shall be efficiently eross stayed or strengthened in some other effective HI (inner. 171. Rivets securing compensating Rings and Stand Pipes. For manholes or frames.-—Th"-1 total effective shear strenirtb of the nvnts on ,eh side of the longitud'iui.l centre line shn.ll be not loss than the 1 ensile strength of that portion of the shell plate, as found by .Regulation 170, which is removed and the rivets securing any cimpojuatiiig ring or frame shall bo so a-iangad that the joint •efficiency calculated on any line parallel to the axis of the boiler through any part of such ring or frame shall not be leas than 1 ho efficiency of the longitudinal noara of the boiler. For stand pipes.—-Where the hole in the shell to accommodate a, stttndpipe does not exceed 8 inche-- diameter, the total effective shear strength of I ho rivets on each side of t b j lo-ij;itudimil centre line shall not bo loss than 75 por cent, of Hi'- tensile stren/th of the portion of th/i plate, astound by Regulation 170, which h»s been removed The strength of rivets in double shear shall bo taken aa 1 • 875 times the strength of rivets in single shear. RIVETING 172. Rivet Holes.—(a) Kivot holes shall not be punched, but shall be drilled full aizo from the solid plate, and wherever possible, rivet holes shall be drilled in place with platen, straps and ends bolted in position. After drilling, the plates shall be separated, the burrs and the sharp edges of the holes shall be removed and the contact surfaces of the plates shall be cleaned. All taoking holes shall bo drilled to a si/,e which will allow tho holes to be enlarged to the required rivet size by drilling or reamoriiig. All rivet holes shall be slightly countersunk under each rivet head. (b) The diametei of the rivet hole shall be not more than 1/16 in. larger than 'the standard diameter of the cold rivet as manufactured. (o) Where sizes of rivets are mentioned the sizes refer to the diaraeters""of the rivet holes not to the diameters of the rivets used before closing. 173. Riveting.—(a) Rivets shall be closed by hydraulic, maohinery wherever the design of the boiler permits ; the rivets may bo closed by hand or pneumatic ihammer in position where hydraulic riveting is impracticable. 666 TEH GAZETTE OF INDIA EXTBAOEDINAEY [PAKT D (b) Rivets shall be of sufficient length to fill rivet holes and form sound and substantial heads. The headu shall be finished concentrically with the rivot shanks- . Rivets shall bo heated uniformly throughout thoir full length. (c) Drift pins shall not bo used with such force as to distort the rivet holes. If the rivet holes are found not to be fair when, the plates arc bolted up for riveting- the holes shall bo roamered fair before the riveting is commenced. (d) For hydraulic riveting the pressure shall be the loast neoessary to ensure a tight joint, and only sufficient pressure shall be used to close the rivets properly and seouroly without indenting, buckling or otherwise damaging the plate. The rivets shall be allowed to shrink while under pressure from the riveting machine. 174. Fullering and Caulking.—All seams shall be fullered or caulked inside and outside and this shall bo done in such a manner that the plates are not sprung or damaged. CHAPTER IV REGULATIONS FOR DETERMINING THE WORKING PRESSURE TO BE ALLOWED ON VARIOUS PARTS OF BOILERS OTHER THAN FUSION WELDED AND SEAMLESS FORGED DRUMS. 175. The maximum pressure u,t whioh a boiler may be used shall be deter- mined in accordance "with the provisions of this Chapter. The "Regulations in this- Chapter refer to material subjected to steam temperature not exceeding 500°F. SHELLS 176. Formula for working pressure oi shell.- (a) For cylindrical shells, barrels, steam and water drums, and dome-* of boilers the maximum working pressure per square inch to be allowed shall be calculated from the following formula :— [NOTE. Where parts of drums uf water tubo boilert are perforated for tubes, the work- ing pressure shall be calculated by equation (53) under 'Tube Plates*.] (t—2) X S X J W.P. == • — Eqn. (1) C x P W.P. is the working pressure in lbs. per square inoh, t ifl the thickness of shell plates in 32nds of an inoh, S in the minimum tensile breaking strength of the shell plates in tons per square- iiHi or whatever strength ia allowed under Regulation 5, .1 is the percentage of strength of the longitudinal Beams of shell or of a line of hole1 in the shell for stays, or rivets, or of an opening in the shell not fully compen- sated, whichever is least calculated by the methods hereafter described, ( is n. co-efficient as follows :— 2'7--> -when the longitudinal seams are made with double butt straps and when small sh '11K are formed from solid rolled sections ; 2-H'J when the longitudinal Hoams aro made with lap joints and are treble riveted ; ;>•()-when 1 he longitudinal seams are made with lap joints and are double riveted ; :!•() when the longitudinal seams are welded and are filled with a single butt strap : !(-3 when the longitudinal seams are made with lap joints and are single riveted. D ib the inside diameter of the outer strake of plating of the cylindrical shell measured in inches. Sao. S] THE GAZETTE OF INDIA EXTBAOBtflNAE? (MPT (b) The Factor of Safety flhall in no oase be less than 4. The aot.ual Factor of Safety in each oase may be found from the equation :— t F=.l-4xCX— -. t-2 With the best form of joint and least co-efficient (C) the Factor of Safety for sholl plates, £inoh to If inohes in thiokness, varies from 5 13 to 3-99. (o) An addition of 10 per cent, whall be raado to the appropriate co-efficient for sheila of boilers in "which the longitudinal seams are lap jointed and aie not tiewsKible to close visual innpeotion and for shell plates of externally fired boilers exposed to the direct, impact of furnace flame ; provided that this addition nbaJl not apply to the steam and water drums of water tube boilers where tho drums aie not close to the fire-grate and there are tubes between the fire-grate and the drum. (d) The above co-efficient are standards and shall be used only for boiler open to inspection by an' Inspecting Officer during the whole period of construction And which arc oertified by Mm as having boen constructed in accordance with Lhe ataivl- ard conditions laid down in these Regulations. 177, Methods o£ calculating the strength ol riveted joints.--(a) The percentage of strength of a riveted joint (J) shall be found from the following forniiuse (i) (ii), (iii) : (i) and (ii) are applicable to any ordinary typo of joint ; (iii) is applicable only to that type of joint in which tho number of rivetP in the inner COM S is double that of the outer row. The lowest value given by the application of these formula? is to be taken as the percentage of strength of tho joint (.onipiiml with the solid plate. 100(P— D) (i) = Plate percentage . . . . . . Eqn. (2> P I U O X A X N X C X S J (ii) ——-————- —- Rivet percentage . . . . Kqn. (3> PxTxS 100(P-210) lOOxAxCxfij (iii) 1—• — — — —Combined plate and rivet jjorccnta^c. Eqn. (4\ P P x T x S F is the pitch of rivets ut outer row in inches, D is tho diameter of rivet holes in inches, A iB th^ sectional area of one rivet hole in square inchc-, N JB the number of rivets per pitch, (P), T is the thiokneuH of plate in inches, C >̂1 for rivets in single shear atj in lap joints, and 1-875 for rivets in double shear as in double butt strapped joints, Sj in the shearing strength of rivets, which shall be taken to be 23 tons per square inoh for steel and 18 tons per square inch for iron, S is the minimum tensile bieaking strength of shell plates in tons per squam inch, or whatever strength is allowed under .Regulation 5 of Chapter I. In the first formula (i) D is the diameter of the rivet holes in tho outer row s and in the third formulw J) is the diameter of the rivet holes in the next rows, [n the last formula A is the area of one ris ot hole in the outer row. (b) When the sectional area of the rivet holes is not the same in all rows, and when some of the rivets are in double shear and others in single shear the rivet aeotions per pitch of each size or shear Hhall bo gomputed separately mid added together to form tho total rivet section. «68 THE GAZETTE OF INDIA EXTRAORDINARY [PABT II 178. When Pitch exceeds maximum allowed.—Should the pitch of tho rivets exceed the maximum pitoh allowed, the permissible pitch shall he used in place of the aotual pitoh in determining the percentage of plate section. No greater percentage than 85 shall be allowed for any type of riveted joint. 179. Butt Straps and spacing of rivets below requirements.—Should the spacing of tho rows of rivets or the distance between edge of plate and rivet hole or the thick- ness of butt straps be lees than is specified in Regulations 182 and 184 the percen- tage representing the strength of joint shall be m idifled afl prescribed in those regulations. 180. Percentage of Welded and Strapped Seams.—In determining the percentage of strength of a welded seam covered by a strap or straps the formulas and allowances in Regulations 177, 178 and 179 shall be applied, but 50 per cent, shall he added to the rivet peroentago for the weld, 181. Percentage to be allowed lor Solid Rolled Shells.—When small shells are rolled from the solid, J. in equation (1) shall he taken as 100 per rent. 182. Thickness of Butt Straps.—The minimum thickness, of butt wtraps for tlie^ longitudinal seams of cylindrical shells shall be determined by the following formulae but all straps should be of sufficient thickness to permit of efficient caulking, and in any case shall not be less than 3/8 inch in thickness. Single butt straps having ordinary riveting :— 1125T=, Tj Eqn. (5) Single butt straps having every alternate rivet in the outer rows omitted :— (P-D) 1-125TX = Tt tiqn. (6) (P-2D) Double butt straps of equal width having ordinary riveting :— •625T ^ T Eqn. (7) Double butt straps of equal width having every alternate rivet in the outer rows omitted :— (P-D) •625TX — - = T2 . Eqn. (8) (P-2D) Double butt straps of unequal width either having ordinary riveting, or having every alternate rivet in the outer rows omitted. •75T =• Tx (wide strap) Eqn. (9) r • 625T = Tj (narrow strap) Eqn. (10) Tx is the thickness of the butt straps in inches. The other symbols have tho same significance as in Regulation 177. Single and wide butt straps shall, wherever practicable, be on the inside of the shell. Should tho thickness of butt straps be less than that above described, the least percentage of joint as determined under Regulation 177 shall be reduced hi the pro- portion of the actual thickneBB to the proscribed thiokness, , 183. Maximum Pitch of Rivets in longitudinal joints.—The maximum pitoh of the rivets in the longitudinal joints of boiler shells shall be :— OxT+1 -625 =• maximum pitoh in inohes Eqn. (II) T is the thickness of the shell plate hi inches, BHO. 8] THE GA^l ixuOx. INDIA J^AI. AO±U>1 AJ* . 6, 0 is a co-efflcient as given in the following table :— Number of Kiveta pfr pitch 1 3 4 5 Co-effloiento for Lap joints 1 31 2-63 3-47 4-17 Co-effloients for oinfile Butt-utrupped joints I B S 3'06 4>0rt Co-effloionts for double Rutt- atrapped joints 1-76 3 50 4 03 8 52 6 00 184. Spacing ot rows ol rivets. -(«) In joints, whothei lapped or fitted with butt straps, in which there are more than one row of rivets and in which there is an equal number of rivets in eaoh row, the distance between the ro^ s of rivets shall be not less than— ?jig-zag riveting. •33P+- 67D => distanoe between oentre lines of rows (R) . '. Bqn. (12) Chain riveting, 2D = distance between centre lines of rows (R) , . . Eqn, (13) (6) In joints in which the number of rivets in the outer rows is one half of the aumber in each of the inner rows, and in whioh the inner rowa are chain riveted the distance between the outer rows • nd tho next rows shall bo not less than as required by equations (12) and (13) whi lever is the greater, and tho distanco between the rows in which there are the full number of rivets shall bo not lesa than 20(1^). (o) In joints in •whioh the number of rivets in tho outer rows is ono half of the number in eaoh of the inner rows and in which the inner rows are zig-zag, tho dis- tance between the outer rows and the next rows shall bo not less than— •2P + 1-15D =• distance between centre lines of outer and next rows (R) Eqn. (14) The distance between the rows in which there are the full number of rivets shall b« not leBS than— • 165P+ • 67D=dietanoe between oentre lines of inner rows (RjJ Eqn, (15) P is the pitch of the rivets in the outer rows, D is the diameter of the rivot holes in inches or the mean of the diameters of rivet holes when the distance to be determined is befrweon two rows of rivets of different diameters. (<2) Should the distance between rows of rivets be less than as prescribed above the plate percentage determined by equation (2) shall be modified thus— actual distanoe 100 [P—(2 - — -—-D)] prescribed distance ——-— —- =-> modified plate percentage, . Eqn. (16) P (e) In all oases the clear space between a rivet holo and the edge of a plate shall not be less than the diameter of the rivet holes, i.e., the centro of the rivet hole shall be at least \\ diameters distant from the edge of the plate (E)— Provided that, if thia condition be not observed, the strength value of the rivetB affeoted shall be reduoed in the proportion of the aotual distance between the outer •dge of the rlveta and the edge of the plate to the prescribed distanoe. «60 T. ih GAzjii'Ilj^ OM iNDlk JL^lJtAUJWjlMA. »J. L+A*,: u u

Previous and next

All provisions of Indian Boiler Regulations, 1950.

Questions people ask

Is regulation 184 of Indian Boiler Regulations, 1950. still in force?

No repeal of Indian Boiler Regulations, 1950. is recorded.