LawGrids logoLAWGRIDS.ORG

Regulation 43, Indian Boiler Regulations, 1950.: (a) Material

Indian Boiler Regulations, 1950. - Regulation 43

Text of regulation 43

(a) Material

43. (a) Material.—To comply with Regulation 36(a). (b) Annealing.—The ondt- of all tubon shall be carefully annoaled to a length not less than 0" if they have been submitted 1o a process of swelling or reducing the end dimensions. (c) Freedom from defects.—To comply with Regulation 36(c). (d) Tolerances.—The tubes shall be of the dimensions spooifiod, straight, cylin- drical, of uniform thickness and edema 1 diamol er i hroughout, subject to the working" margins piveti in the table below:— (i) Diameter.—The external diameter of the tubetj measured at any point shall be within the following tolerances of diameter specified :•—- OntmtU) d [lUnoter of tiibns. Up to tirid including 2J in. O v e r 24 i n . . . . T o l e r a n c e . ^ 1 /04" — 1 / 3 2 " H 1 % - (ii) Thickness.—Tho thickness of the tubes shall be within the following toleranoen •- — Outsido rlinintjter of tubes. Up to ami moluding 2J in. O^er 2} m Tolerance J 17*% - 71% ^ io% — 0% Whero the ends of the tubes are swelled or reduced the thickness at the enda may be decreased below or increased above the nominal thiokness of the tubes by an amount in proportion to the percentage of aueh swelling or reduction and, in addition to this allowance, the tolerances relating to thickness shall also apply. (Jii) Length.—The tubos shall be not less than the nominal length but may «xcccrl it by the amount given below :— Up to and including 30 it. Over 30 ft 1/8 in. iH in. (e) Selection of tubes for test.—To comply with Regulation 37. 44. (a) Tensile Test Tost pieces out from the ends of tho annealed portions removed from tho ends of the selected tubes shall comply with tho folio-wing require- ments :•— — • Strips cut from tubes und tested in thoir curvod condition. Test lengths) tuken from fliiishod tubas («nda ul tubtiH to be plugged from gripa). Ultimate tunsile utroHH ul tona por HCJ. in. Not loss than 20 20 Not more than 28 Minimum nlongution ptir rent. on 8 1/4 in. thick and over 20 25 in. Lena than 1 /4 in. thick 18 23 on '2 in. 1/4 in. thick and over ,-JO Leni thn,ii 1/4 in. think 28 (b) Flattening Test-—A ring not less than 2 inches in length cut from the anneal- ed portions removed from tin1 ends of the selected tuboH Hhn.ll be flattened between two parallel flat surfaces, (he width of which shall be not less than ] J times tho diameter of the tube. When the pressure is released, the interior surfaces of the test piec,c at the middle shall remain at a distance apart of not more than three times tho thickness of tho tube and 1 he test piece shall then show no sign of crack or flaw. (o) Expanding Tests.- -The annealed tube ends shall wilhstand expanding by a drift expander having a total included angle of between 40° and 60° (20° to 30° per side) to the following increase in external diameter without showing truck or flaw:— Thieknoas ol Tube °. S.W.O. mid thinner Thinner than 5 S.W.G. und up to and including 3 8.W.G. Thicker thun 3 S.W.O. Increune in Diameter peT o«)it. IB 12 0-fi

Previous and next

All provisions of Indian Boiler Regulations, 1950.

Questions people ask

Is regulation 43 of Indian Boiler Regulations, 1950. still in force?

No repeal of Indian Boiler Regulations, 1950. is recorded.