LawGrids logoLAWGRIDS.ORG

Appendix A, Legal Metrology (General) Rule, 2011: APPENDIX A

Legal Metrology (General) Rule, 2011 - Appendix A

Text of appendix A

APPENDIX A

APPENDIX A TEST FOR HARDNESS OF MAXIMUM INDICATING DEVICE 1. Apparatus (1) Centrifuge-A centrifuge with radial arms · 15 cm each. Each arm shall be provided with a pocket for keeping one or more clinical thermometers. Speed of the centrifuge shaU be either fixed or adjustable to 600 rpm. 2. Procedure (1) Place the thermometers for some time in water at a temperature anywhere between 42 and 43°c. (2) Then put them In the pockets of all the centrifuge, bulb facing outwards, that is away from the axis of the centrifuge while In rotation. (3) Let the centrifuge work steadily at its correct speed for at least 2 minutes. Then stop it. (4) Take the thermometers out of the pockets and observe the mercury column. (5) Thermometers shall be taken as having satisfied the requirement of this test, if the mercury rests below or at 35°C mark. Important-It is necessary that the room temperature does not exceed 34.5°C during the test. APPENOIXB TEST FOR ACCURACY 1. Apparatus (1) Comparator Bat?Elther screw type or bubbler type, as prescribed In JS 6274-1971 Method of calibrating liquid-in-glass thermometers, filled with water. (2) Reference Thermometers-Calibrated reference thermometers [see Schedule Mark 8 and 9 of the IS 4825-1982 specification of liquid-in-glass solid-stem reference thermometers (first revision)]. 2. Procedure , (1) After preliminary check of the clinical thermometers, carry out the accuracy test In accordance with 6.2 ofIS 6274-1971 at 37.6 ± 0.5°C, 39.0 ± O.S°C and 41 ± 0.5°C respectively. (2) The thermometers shall be considered to have passed this test if the accuracy so determined lies within limits prescribed in paragraph 6(2). APPENOIXC TEST OF TIME OF RESPONSE 1. Apparatus Same as in paragraphs 1(1) and 1(2) of Appendix B provided that some automatic arrangement is made to switch off stirring at the instant the bulb of thermometers under test touch the water surface and to switch it again immediately after the thermometers are taken out of the water. 2, Procedure (1) Set the comparator oath at a temperature of 41 ± 0.5°C. Note the temperature on the reference thermometer. [ 'WT II - "!!!11'6 3 ( i) ] 583 (2) Shake down the clinical thermometers under test to maximum extent. Note: Centrifuge mentioned under para 1(1) of Annexure A may be used for this purpose, if required. (3) Plunge the clinical thermometers Into the bath upto 35°C mark. Take out suddenly after 7.5 to 8.0 seconds wipe and dry. Take their readings. (4) Thermometers sha II be considered to have passed this test, If they Indicate temperature within ± 0.1 °C of the comparator bath temperature noted in paragraph 2( 1) of this Appendix. Important-It Is necessary that the room temperature does not exceed 34.5°C during the test. · PARTC CLINICAL ELECTRICAL THERMOMETERS WITH MAXIMUM DEVICE 1. Scope (1) This Part specifies the metrological and technical requirements for clinical electrical thermometers with a maximum device. Such instruments are designed to measure human or animal body temperature. They indicate a maximum temperature measured after a steady state is reached or predicted after a time specific to the design of the instrument. Until the maximum temperature is indicated, the actual temperature may be indicated by the thermometer. (2) The measuring range of clinical thermometer shall be either of 35°C to 42°C or 35°C to 43°C. Two accuracy classes, class I and class II, are covered by this specification. (3) This specification appliesto battery-powered instruments which provide a digital Indication of temperature. (4) Oinical electrical thermometers designed to measure skin temperature are not covered by this specification. (5) This specification does not exclude the use of any contract device based on other measurement principles that meets equivalent performance standards in determining maximum body temperature at specified time intervals. 2. Terminology (1) A clinical electrical thermometer, as covered by this specification Is a contact thermometer comprising a temperature probe and an indicating unit, and that Is designed to measure human or animal body temperature. (2) A temperature probe is the component of a thermometer of which part is applied to a body cavity or tissue with which It establishes thermal equilibrium. It comprises a temperature sensor with associated parts includ;ng coverage, seals, Inner leads, and connecting plug, where appropriate. Notes : 1. A body or tissue may be the mouth (sublingual}, rectum, or armpit. 2. The part of the probe In contact with a body cavity or tissue is called the 'applied part'. 3. An Indicating unit Is the component of a thermometer that process the output signal of the temperature sensor and displays the measured temperature. 4. A maximum device Is the component of a thermometer that monitors over a specified time the temperature measured by a probe in contact with a body cavity or tissue, at which it indicates the maximum temperature and maintains the indication until reset by the user. 5. Predicting clinical electrical thermometer calculates the maximum temperature of a probe In contact with a body cavity or tissue, without waiting for thermal equilibrium to occur, by using heat transfer data and a mathematical algorithm. 3. Description of the instrument (1) A complete thermometer consists of a temperature probe connected to any indicating unit. The Instrument may be of the following type:..:. -Indicating unit that is compatible with the characteristic response of a probe. 4. Metrologlcal requirements (1) Unit of measurement-measuring range-scale interval · (a) The unit of temperature shall be the degree Celsius 0C. (b) The measurement range shall be a minimum of 35°C to 43°C or 35°C to 42°C. Greater measuring ranges may be sub· divided into partial ranges; however, the range 35°C to 42°C shall be continuous. (c) The scale interval or digital increment shall not exceed- , 0.01 °C for class I thermometers, • 0 .1 °C for class II thermometers. (2) Maximum permissible errors (a) The maximum permissible error under reference conditions for the temperature range 32.0°C to 42.0°C for the two accuracy classes covered shall be as follows:- ·--- ---- --------- _J _ 584 .THE tG'AZETTE ,OF 1JND1A: EXTRAORDINARY [PARTII-SEC. J(i)] Maximum·permissible errors'(range:32;0°c to 42:ooq (b) outsice.the temperature range 32°C to 42°C,.the maximum errors.shall be at twice the vatues.specltled .m ;paragraph 4(2)(a). (3) Reference conditions The reference. conditions for the requirements of paragraph 4?),shall be: ambiennemperature of 27°C ± s•c relative·humldlty to 50% ± 20% the instrument operating within the specified range of battery voltage (specified power:sup,plyconditions). (4) Time response The :thermometer shall be submitted by , the manufacturer to a testing laboratory to determine Its time response. The test shall be based on any analysis of a significant sample of human subjects. The difference between the displayed calculated temperature and the corresponding measured temperature at thermal equilibrium of calculating (predicting)thermometer shall not exceed 0.2°c. 5. Technical requirements (1) tempersture probe (i) For an Interchangeable probe of the resistance type, the manufacturer shall specify the maximum power that may be supplied to the probe by an Indicating unit; this power shall not cause energy dissipation (FR) giving rise to any increase in temperature by more than 0.02°C when immersed In a reference water bath maintained at a temperature range of 36.9°C to 37.1°C. Note :(1) For a description of the reference water bath, see Annexure A. (2) A test of this requirement is only applicable to inter-changeable probes submitted for pattern approval without a specific Indicating unit. When a probe is submitted with an associated Indicating unit, the requirement in 5(2)(7) applies. Accuracy dass Class I Class II Complete -Indicating ;Temperature thermometer unit probe ± o.1s•c ±.o.os•c ± O.l'C ± 0.2!C + 0.1 •c :.± 0.1°C (ii) The thermal stability of the probe, after exposure for 100 hours at 80°C ± 2°C or 300 hours at 55°C ± 2°c, shall be such that the requirement for maximum permissible errors specified in paragraph 4(2) Is met. (Ill) The electrical insulation of the probe shall be sufficient to prevent a change In Indicated temperatures greater than ± 0.02°C when the probe is immersed In an electrically conducting liquid having an Insulation resistance of 80 MW at 20°C. This Insulation includes that between the Inner lead wires, that between the wires and the surface of the probe, and that encasing and protecting connections and transitions. (Iv) The locations of the sensors in the probe shall be such that, when the probe Is Immersed to depths greater than SO mm from its tip in a reference water bath at a temperature does not vary by more than o.os•c from that Indicated at a depth of SO mm. (v) The probe shall be strong enough to withstand mechanical stresses expected under normal conditions of the use. (vi} If the probe is inter-changeable, it shall be fitted with either a plug-in or quick dis· connectable electrical connector. The contact resistance of the connector or the Insulation resistance between the circuits of the' connector or to ground shall not cause a variation In the indicated temperature greater than 0.02°C. Note : The connectors may not be required to be water resistant. (vii) The probe shall meet the requirements for maximum permissible errors specified In paragraph 4(2) when the applied part has been subjected to the cleaning In and disinfecting procedure specified by the manufacturer. Notes: (1) For small compact thermometers this applies to the complete instrument. (2) The materials of the probe that come into contact with the body should be selected for compatibllity with body tissue. (viii) The output signal of the probe shall not vary by more than ± O.OS°C when the temperature of the cable connecting It to an Indicating unit varies by 20°C. ['WT 11-¥16 3(i)] (2) Indicating unit (i) When connected to a resistance-type temperature probe, the indicating unit shall provide an energizing potential sufficiently low so that energy dissipation ( 1' R) In the probe shall not cause an increase in indicated temperature of over 0.01 •c when the probe Is immersed in a reference water bath at a temperature wi.thin the specified measuring range. (ii) The Indicating unit shall not Indicate a temperature when connected to a battery charger. (iii) The digital display of temperature shall be at least 4 mm In height or it shall be optically magnified so as to appear at least 4 mm in height. (iv) The indicating unit shall provide a clear indicating or warning signal when the measured temperature is outside the specified measuring range. (v) The Indicating unit shall include a self­ checking device that meets the requirements of the paragraph 4(2). This device, which may be manual or automatic, shall input a predetermined electrical signal. Failure shall be clearly indicated. Note : This device checks only the operation of the indicating unit and does not ensure that a temperature measurement Is correct. It provides a means of detecting a faulty operation caused by a defective component or other disturbance. (vi) In the case of a predicting thermometer, the indicating unit shall provide a means of displaying the measured temperature after reaching the thermal equilibrium. (3) Complete thermometer Note : The reference thermometer Is that indicated (either before the test, or before and after the test, as appropriate) by the thermometer probe immersed in the reference water bath according to the paragraph 1 of Annexure A, the temperature being held constant within the working range of the thermometer. · (I) The thermometer shall provide a clear indication or warning signals when the battery voltage Is outside the specified limits and it shall meet the requirement specified in paragraph 4(2) when the voltage Is within these limits. u t o r;r/!l-1 lf 7 585 (ii) The indicated temperature shall not vary by more than ± 0 .1 °C from the reference temperature when the temperature of the thermometer casing varies from 10°C to 40°C. (Iii) The indicated temperature shall not vary more than ± 0.1 °C from the reference temperature after a thermal shock resulting from an abrupt change In temperature from -s-c tc-so-c, (Iv) The indicated temperature shall not vary by more than ± O.1 •c from the reference temperature after storage for 24 hours at· 20°c ± 2°c and at 60°C ± z-c, (v) The indicated temperature shall not vary by more than ± O.1 •c from the reference temperature after storage at a relative · humidity of 91 % to 95% at a temperature constant within± 2°C in the range 20°C to az-c. (vi) The indicated temperature shall not vary by more than ± 0.3°C from the reference . temperature during exposure to electromagnetic field having a frequency between 150 kHz and 500 MHz and a field strength of lOV/m. (vllf The indicated temperature shall not vary · by more than ± 0.1 °C from the reference temperature after fall on to a hard surface from a height of tm from three different orientations. (viii) Small and compact complete thermometers shall be water resistant. 6. Practical Instructions (1) Manufacturers shall provide an operating manual, or Instructions, including the following information:- • description of appropriate uses and means of applications, • Identification of the specified temperature measuring range of the complete thermometer taking into account, If applicable, the specified measuring ranges of both the interchangeable probes and the indicating unit, Instructions and precautions for deaning and disinfecting the complete thermometer or the inter-changeable probes, Identification of components and suitable Inter-changeable parts such as probes and 586 THE GAZETTE OF INDIA : EXTRAORDINARY [PARTII-SEC. 3(i)] battertes.vtncludlnq nominal voltage,; if applicable, • minimum time. for .. achlevlnq .thermel equilibrium, • description of transition fromthe·predicted temperature,measuring -rnede Into •the actual .temperature,measuring mode, instruction for the self,checklng device, • information on the.correct ·environmental conditions .of use, .storaqe, and transport of the:thermometer. (2) Specit1c·1nformation should be provided by the manufacturer, on request, regarding possible sub­ standard performance if used under the following conditions:- • outside 'the ,presc.ribed environmental temperature .and humidity range, • after an accidental mechanical shock. 7. Metrologlcal controls (1) Pattem .evsiuetion (i) Manufacturers shall provide the following information 1- locatlon of sensor from tip of probe, description and principles of measurements of complete thermometer, description of electrical principlesand of any necessary equipments provided, description of test for self-checking device, specified working range for battery, nominal and specified temperature measuring ranges, nominal values of calibrations data for type of temperature probe, as applicable, precautions for cleaning and disinfecting complete thermometer or temperature probes, as appropriate, including test results as specified in paragraph 3 of Annexure B, Indicating on instrument if a displayed value is calculated, test results, results of clinical test of time responses [paragraph 4(4) and Annex OJ, operating manual and/or instructions (see clause 6). (ii) Thermometers shall be subjected to the following tests:- Note : Requirements for the reference water bath and the test for maximum permissible errors are provided In Annexure A. The performance requirements for the Instrument and Its major components are provided In paragraphs 4 and 5. Where · appropriate, an additional description of required tests is provided In Annexure B. Probe maximum permissible errors (4(2) and paragraph 2(2)(1) of Annexure A] long-term thermal stability [5(1)(11)] electrical insulation and water resistance [5(1)(111)and paragraph 2 of Annexure BJ. location of sensor [S(l)(iv)] mechanical strength [5{1)(v)] electrical contact resistance of connector [5{1 )(vi)] cleaning and disinfecting [5( 1 )(vii) and paragraph 3 of Annexure BJ stability with changes in temperature of cables [S(l)(viii] Indicating unit maximum permissible errors (4(2) and Annexure A] power provided to probe [5(2)(1)and paragraph 1 of Annexure BJ indication when connected to battery charger [5(2)(ii)] indication If the thermometer· Is outside the specified measuring range [5(2)(1v)] self-checking device [5(2)(v)] display of predicting thermometer [5(2)(vi)] Complete thermometer maximum permissible errors (4(2) and Annexure A] low battery Indication [5(3)(1) and paragraph 4 of Annexure BJ ambient temperature [5{3)(ii) and paragraph 6 of Annexure BJ ['IJT'Tn-= 3(ilJ ··;'""" •. ,, . ..:.., .. ··" ,. ,··?--?·-- 587 thermal shock [5(3)(iil) and. paragraph 6 of Annexure BJ storage temperatures [5(3)(1v)J humidity [5(3)(v) and paragraph 7 of Annexure BJ electromagnetic radiation inter­ ference [5(3)(vi) and paragraph 8 of Annexure BJ mechanical shock. [5(3)(vli) and . paragraph 9 of Annexure BJ water resistance of small compact thermometers [5(3)(vlll) and Annexure CJ Instructions and precautions for cleaning and disinfecting the complete thermometer or the inter­ changeable probes, Identification of components and suitable inter-changeable parts such as probes and batteries, Including nominal voltage, if applicable, minimum time for achieving thermal equilibrium by an indicating energy dissipation requirements [S(l)(a) and paragraph 1 of Annexure BJ (iii) A report of the results of tests required in paragraphs 7(1)(ii) and 7(1)(111)shall be prepared. (2) Marks and labels (i) Manufacturers shall provide a space for marks and labels. · (ii) Manufacturers shall affix on the thermo­ meter or Indicating unit, if separate, the following marks or labels:- name and address of manufacturer or supplier, and/or trademark, model or type designation, and serial or lot number, temperature values or Indications given by the self-check.Ingdevice, indication of the orientation or position in sue, where appropriate, indication if a displayed value is calculated. (iii) Inter-changeable temperature probes shall bear the following marks or labels::- name and address of manufacture and/or trademark, type designation, serial or lot number, or relevant manufacturing production data. (iv) A single-use temperature probe shall be sealed In a package on which the information specified In paragraph 7(2)(iii) and the measuring range shall be indicated. In addition, sufficient space on the package shall be provided for the application of official approval marks. It shall be clear If the package has been opened and the Instructions shall stipulate that the user only opens the package Immediately before use. (v) The testing laboratory shall permit the application in a conspicuous place, of the following:- pattern approval mark or label, on each complete thermometer or indicating unit and associated temperature probe(s). indication of. the specified temperature measuring range If the . total range of the thermometer Is greater. (3) Verfflcatlon (I) The laboratory shall examine the Information provided by manufacturers as specified in paragraph 6. (II) The laboratory shall examine the Instrument's pattern approval certificate mark(s) or label(s). (Ill) The laboratory shall cany out any of the tests indicated in paragraph 7(1)(ii) that may be critical for the designated application of the instrument. Note: The tests indicated In paragraph 2 of Annexure A may be sufficient for verification. (Iv) The laboratory shall provide a verified Instrument with a mark or label. (v) The water resistance of small and compact complete thermometers shall be examined by means of the procedure described In paragraph 2 of Annexure C. (vi) The laboratory shall indicate the period of validity of the verification.

Previous and next

All provisions of Legal Metrology (General) Rule, 2011

Questions people ask

Is appendix A of Legal Metrology (General) Rule, 2011 still in force?

No repeal of Legal Metrology (General) Rule, 2011 is recorded.