Rule 93B, THE CENTRAL MOTOR VEHICLES RULES, 1989: Overall dimension for power tillers
THE CENTRAL MOTOR VEHICLES RULES, 1989 - Rule 93B
Text of rule 93B
Overall dimension for power tillers
4[93B. Overall dimension for power tillers.—(1) The overall length of the power tiller with a riding
attachment shall not exceed 3.5 metres.
(2) The overall width of the power tiller with a riding attachment including case wheelers shall not exceed
1.5 metres.
(3) The maximum overall height of the power tiller shall not exceed 2.0 metres.
(4) The overall length when of the power tiller when coupled to a trailer shall not exceed 6.0 metres.
(5) The maximum overall width of the power tiller when coupled to a trailer shall not exceed 1.7 metres.
(6) The maximum overall height of the power tiller when coupled to a trailer shall not exceed 2.0 metres.]
94. Condition of tyres
5[(1) 6[Every motor vehicle including agricultural tractor and its trailer] shall be fitted with pneumatic
tyres and every construction equipment vehicle, other than steel drum rollers of vibratory compactors or
compactor rollers or road roller or a track laying vehicle, shall be fitted with pneumatic tyres or solid
rubber tyres.]
(2) The pneumatic tyres of a motor vehicle including agricultural tractor and its trailer shall be kept
properly inflated and in good and sound condition.
________________________________________
1. Inserted by G.S.R. 642(E),dated 28-7-2000 (w.e.f. 28-7-2000).
2. Renumbered by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. Inserted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
4.Subs by GSR 589 (E),dated 16th September,2005
5. Substituted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
6. Substituted by G.S.R. 111(E), dated 10-2-2004, for “Every motor vehicle” (w.e.f. 10-8-2004).
73
(3) For the purpose of sub-rule (2), a tyre shall not be deemed to be of good and sound condition
if—
(i) any of the fabric of its casing is exposed by wear of the tread or by any unvulcanised cut or
abrasion in any of its parts; or
(ii) it shows signs of incipient failure by local deformation or swelling; or
(iii) it has been patched or repaired by an outside gaiter or patch other than a vulcanised repair;
1[(iv) the Non-Skid Depth (NSD), shall not be less than 0.8 mm in the case of two wheeler and
three-wheeler and 1.6 mm in the case of other motor vehicles, below the Tread Wear
Indicator (TWI) embedded in tyres at the time of manufacture:]
Provided that the requirement specified in clause (iii) shall not apply to a temporary repair
effected to enable the vehicle to be moved to the nearest place where the tyre can be repaired or
replaced:
Provided further that where a motor vehicle, other than road roller or track laying vehicle, is
not fitted with pneumatic tyres, it shall not be used in a public place unless it is fitted with shoes or
other suitable device so that plying of such vehicle does not damage the road:
2[Provided also that the requirements of the Non-Skid Depth (NSD) and Tread Wear
Indicator (TWI) specified in clause (iv) shall not be applicable for the agricultural tractor tyres.]
95. Size and ply rating of tyres
3[(1) The tyres including radial tyres used on all motor vehicles manufactured or imported on and
after the 1st day of April, 2006, other than agricultural tractors, construction equipment vehicles and
power tillers shall comply with the requirements specified in 4[ IS:15627-2005 or IS: 15633-2005 or
IS : 15633-2005 applicable
Provided that the selection and fitment of tyres for motor vehicles manufactured or imported
on and from the 1st day of April, 2006 shall be in accordance with AIS: 050:2004 in the case of two
and three-wheelers and AIS: 051:2004 in the case other motor vehicles, till such time the
corresponding BIS specifications are notified under the Bureau of Indian Standards Act, 1986 (63 of
1986):
Provided further that Central Institute of Road Transport, Pune and any other agency which
may be authorised by Central Government from time to time can carry tests for verification against
AIS:044:2004 for tyres for the purposes of rule 126.]
5[(2)The maximum gross vehicle weight and the maximum safe axle weight of each axle of a
vehicle shall, having regard to the size, nature and number of tyres and maximum weight permitted
to be carried by the tyres as per sub-rule (1), be—
___________________________________
1. Substituted by G.S.R. lll(E),dated 10-2-2004, for “a motor vehicle” (w.e.f, 10-8-2004).
2. Inserted by G.S.R. lll(E),dated 10-2-2004 (w.e.f. 10-8-2004).
3. Sub-R. (1) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
4. Subs by G.S.R. 784 (E), dated 12th Novemebr,2008 for certain words (w.e.f. 1-4-2009)
5. Inserted by G.S.R 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
74
(i) vehicle rating of the gross vehicle weight and axle weight respectively as duly certified by
the testing agencies for compliance with rule 126, or
(ii) the maximum vehicle weight and maximum safe axle weight of each vehicle respectively as
notified by the Central Government, or
(iii) the maximum total load permitted to be carried by the tyre as specified in sub-rule (1) for the
size and the number of the tyres fitted on the axle(s) of the vehicle, whichever is less:
Provided that the maximum gross vehicle weight in respect of all vehicles, including multi
axle vehicles shall not be more than the sum total of all the maximum safe axle weights put
together.
1[2[(2-A) The size of the tyres of a construction equipment vehicle] specified in column (1) of the
Table below shall have a ply rating specified in the corresponding entry in column (2) of the said
Table in respect of maximum weight permitted to be carried by such tyre specified in the
corresponding entry in column (3) thereof:
Provided that the maximum safe load for single axle with two or more tyres shall not exceed
10.2 tonnes.
OFF-THE-ROAD SERVICE: CONVENTIONAL AND WIDE BASE DIAGONAL PLY
TYRES
TABLE
AGRICULTURAL TRACTOR DRIVE WHEEL
Tyre size Designation Ply rating Maximum weight permitted to be carried
(Kgs.)
8.3/8-24 4
6
630
825
8.3/8-32 4
6
730
925
11.2/10-28 4
6
8
900
1120
1320
12.4/11-24 4
6
8
950
1215
1450
___________________________________
1. Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000),
2. Substituted by G.S.R. 720(E), dated 10-9-2003, for the brackets, figure and words “(2) The
size of the tyres of a construction equipment vehicle” (w.e.f. 10-10-2003).
75
12.4/11-28 4
6
8
10
12
1030
1285
1550
1600
1650
12.4/11-36 4
6
1150
1450
12.4/11-38 4
6
8
1180
1500
1750
13.6/12-28 4
6
8
10
12
1120
1450
1650
1750
1800
16.9/14-28 6
8
10
12
1850
2180
2430
2725
ROAD GRADER
13.00-24 8
12
2040
2485
14.00-24 12 3015
OFF TI IE ROAD HAULAGE SERVICE TYRES
Tyre size Designation Ply rating Maximum weight permitted to be carried
(Kgs.)
12.00-20 14
16
2650
2900
12.00-24/25 14
16
3000
3250
13.00-24/25 18 3875
14.00-24/25 16
20
24
4000
4625
5150
16.00-24/25 20
24
28
5450
6000
6700
18.00-24/25 12
16
4750
5600
76
20
24
28
32
6500
7300
8000
8750
WIDE BASE
23.5-25 12
16
20
24
5300
6150
7300
8000
Note.—1[1.] The load rating for tyres not covered by the above Table may be notified by the
Central Government as and when such tyres are introduced on construction equipment vehicles, and
until these are notified, the provisional load rating declared by the construction equipment vehicle
manufacturer may be certified by the certifying test agency referred to in rule 126.]
2[2. The maximum axle loading capacities shall be verified based on the safe loading
capacities of the tyres. In cases where the axle load exceed 10.2 tonnes, the vehicle manufacturer
shall ask the user to seek the prior permission of the concerned Regional or State Transport
Authorities in whose jurisdiction the construction equipment vehicle is expected to ply depending
upon the conditions of roads/bridges, where deemed fit. Such construction equipment vehicles
whose axle load exceeds 10.2 tonnes shall display permanently on the vehicle a placard indicating
"NOT FOR PLYING ON ROADS". These conditions shall be mentioned in the certificate, issued
by the testing agencies referred to in the rule 126, where the axle load exceeds 10.2 tonnes.]
(3) No tyre shall have a ply rating more than 20, for applications of on-highway and such
ply rating shall not be prescribed by either vehicle manufacturer or employed by vehicle user on this
class of vehicle.
(4) Check on sub-rule (3) of rule 95 on commercial vehicles will be conducted by the
authority indicated in sub-rule (1) of rule 126, while conducting the checks.] 3[(5) Every tyre
manufacturer shall, in addition to any trade mark or size of the tyre, also emboss on it the following,
namely:—
(i) Week and year code or month and year code of manufacture; and
(ii) maximum load carrying capacity.]
4[(6) In the case of Indian manufactured vehicles and imported vehicles (new and old), the size of
tyres if included in the International Standards, namely, ECE, JATMA, ETRTO and T&RA besides
Bureau of Indian Standards may also be accepted under this rule:
Provided that the following conditions shall be complied with:
_______________________
1. The existing note numbered as “1″ by G.S.R. 116(E), dated 27-2-2002 (w.e.f. 27-8-2002).
2. Inserted by G.S.R. 116(E), dated 27-2-2002 (w.e.f. 27-8-2002).
3. Inserted by G.S.R. 221(E), dated 28-3-2001 (w.e.f. 28-9-2001).
4. Inserted by G.S.R 400(E), dated 31-5-2002 (w.e.f. 31-5-2002).
77
(i) that testing agencies referred to in rule 126 shall satisfy themselves about the load and speed
rating of the tyre with reference to the Indian conditions;
(ii) that the test report/certificate issued by the testing agency of the country of origin shall be
verified for acceptance by the testing agency referred to in rule 126;
(iii) that for tubeless tyres fitted on imported vehicles confirming to conditions (/) and (it) shall
also be allowed.]
95 A. Size and ply rating of tyres for agricultural tractor
1[Size and ply rating of tyres for agricultural tractor. (1) The tyre of the agricultural tractor
shall have load carrying capacity as may be specified by the tyre manufacturer, subject to the
condition that the maximum load specified by the agricultural tractor manufacturer shall not be
greater than the load permitted by the tyre manufacturer.
(2) The agricultural tractor manufacturer shall select only that rim size as recommended by
the tyre manufacturer.
Note.—For compliance to the above two sub-rules, the following shall be referred to IS:
13154-1991 as amended from time to time—Tyres for agricultural tractor, implements and power
tillers. In case a particular size of tyre is not listed in IS: 13154-1991, any equivalent International
Standard like Economic Commission of Europe (ECE), Japanese Automotive Tyre Manufacturers
Association(JATMA),European Tyre and Rim Technical Organisation (ETRTO), The Tyre and
Rim Association Inc. (T & RA) and Indian Tyre Technical Advisory Committee (ITTAC), etc.,
shall be accepted.]
——————–
95 B. Size and ply rating of tyres for power tillers
2[Size and ply rating of tyres for power tillers. tillers. (1) The tyre should have load carrying
capacity as specified by the tyre manufacturer, however, the maximum load specified by the power
tiller manufacturer shall not be greater than that permitted by the tyre manufacturer.
(2) The power tiller manufacturer shall select the recommended/ preferred rim sizes only, as
suggested by the tyre manufacturer.
Note.—For compliance to this rule, the following standards shall be referred to, namely:—
(i) 1ST3154-1991, as amended from time to time-Tyre for agricultural tractor, implement and
power tillers.
(ii) In case a particular size of tyre is not listed in IS: 13154-1991, as amended from time to
time, any equivalent International Standard like ECE, JATMA, ETRTO, TNRA, ITTAC,
etc.]
——————–
1. Inserted by G.S.R 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
2. R 95-B inserted by G.S.R. 589(E),dated 16-9-2005 (w.e.f. 16-9-2006).
78
96. Brakes
1[(1) Every motor vehicle, other than a motor cycle, three-wheeled invalid carriage, trailer or
a road roller shall be equipped with two independent and efficient braking systems, namely, the
parking brake and foot operated service brake:
Provided that a motor cycle and three-wheeled invalid carriage shall be equipped with the
independent and efficient braking systems, either both hand operated or one foot operated and the
other hand operated.]
(2) The braking system shall be of strength capable of stopping the vehicle within the
distance specified in sub-rule (8) and of holding it at rest in all conditions and all such brakes at all
time be properly connected and maintained in efficient condition.
2[***]
(3) In every motor vehicle 3[other than agricultural tractors,] the brakes operated by one of
the means of operation shall act directly upon the wheel and not through the transmission gear.
4[(4) Every motor vehicle manufactured on and after the 1st day of April, 2006 shall have a
braking system whose performance shall conform to the following Indian Standard, namely:—
(i) for two-wheelers and three-wheelers IS:14664:1999, as amended from time to time.
(ii) All motor vehicles, other than two wheelers, three wheelers, trailers, semi trailers,
construction equipment vehicles, agricultural tractors and power tillers, IS: 11852 (Part
1) : 2001, 11852 ( Part 2): 2001, 11852 (part 3): 2001, 11852 (Part 4): 2001, 11852 (Part
5): 2001, 11852 (Part 6): 2001, 11852 (Part 7) : 20001 and 11852 (Part 8): 2001 , as
amended from time to time.
Provided that the requirements of automatic wear adjustment specified in para 4.2.1.1.1a of
IS: 11852: 2001 (Part 2), except for those vehicles fitted with Anti-lock Braking System, shall come
into force from the 1st day of April,2007.
Provided further that IS:11852: 2003 (Part 9) shall be applicable for vehicles manufactured
on and after the 1st day of October,2006 fitted with Anti-Lock braking system.]
(5) Except in the case of a motorcycle, the braking system or one of the braking
systems of a motor vehicle shall be so constructed and maintained that it can be so set as
effectively to prevent at least two, or in the case of a motor vehicle having three wheels, at
least one of the wheels from revolving when the vehicle is left unattended.
(6) The braking system or part thereof which functions in the aforesaid manner shall
be known as parking brake and where such a parking brake is designed to be operated by
hand, it shall be known as hand-brake
_____________________________
1. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
2. Proviso omitted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. Added by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
4. Sub-R. (4) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
79
1[(7) (a) In the case of motor vehicles, other than three wheelers of gross vehicle weight
not exceeding 1000 kgs and motor cycles, the service brake shall be acting on all the wheels
of the Vehicle.
(b) In case of three wheelers of gross vehicle weight not exceeding 1000 kgs. if the foot
operated brake does not act on all the wheels, the following conditions shall be fulfilled,
namely:
(i) the foot operated brake shall act on the two wheels which are on the same
axle, and
(ii) in addition to the parking brake, there shall be an independent brake acting on
the other wheel of the vehicle with an independent hand operated control.
(c) In the case of motor cycles, the braking system Operated with the foot or left hand
shall act at least on the rear wheel and the brake operated by right hand at least on the
front wheel.
(d) In the case of agricultural tractors, the braking system shall act as on both the rear
wheels, either directly or through the transmission gear].
2[(8) The service braking system in the case of vehicle other than three wheelers and motor
cycles, and the braking system operated by one of the means of operation other than
the parking brake in the case of three wheelers and motor cycles shall be capable to bring
the vehicles to halt within the distance specified in the following Table when tested in
accordance with the condition prescribed correspondingly in the Table. The test shall be
conducted on a dry level hard road in good condition. During the test the accelerator control
shall be fully released and in the case of vehicles with manual gear shifting control, the top
gear and the clutch shall be engaged.
1
Table.
SI.
No
.
Type of vehicle Load Test speed (The
speed at which the
brake should be
applied) (Kmph)
Type of brake Stopping
distance
(m)
1. All vehicles other than
motor cycles, three
wheelers and
agricultural
tractors
Laden to
the
registered
GVW or
Unladen
30
30
Fool operated
service
13
13
Do Laden or 40 do 21
Do Unladen 40 do 21
1. Substituted by 1G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
2. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
80
2. Motorcycles Unladen 30 Foot or hand
operated 21
3. Three-wheelers
including three-
wheeler
tractors for trailer
Unladen 30 Foot operated
(brakes
operational: on at
least two wheels)
13 Kg
4. Agricultural tractors Laden to
test
mass
25 Foot operated
service
10
5. All other than
threewheelers
of engine
capacity not exceeding
500 cc, motor cycles
and
agricultural tractors
Laden to
the
registered
GVW or
Unladen
30
40
30
40
-do-
-do-
-do-
-do-
12.7
15.0
9.3
12.0
For the purpose of this test for vehicles other than motor cycles the "unladen" means the
vehicle is without any load and shall carry only the driver and another person for specific purpose of
supervising the test, and the instruments, if any. In the case of motor cycles, the "unladen" means
that vehicle will carry only the single rider and the measuring instrument, if any.]
1[(9) The following category of vehicles shall be fitted with Anti-Lock Braking System conforming
to IS:11852:2003 (Part 9):—
(i) N2 and N3 category of vehicles other than tractor-trailer combination manufactured on and
after the 1st day of October, 2006 meant for carrying hazardous goods and liquid petroleum
gas;
(ii) N3 category vehicles manufactured on and after the 1st day of October 2007, which are
double decked transport vehicles;
(iii) N3 category vehicles manufactured on and after the 1st day of October 2007, that are used as
tractor-trailer combinations.
(iv) M3 category of buses that ply on All India Tourist permit, manufactured on and after the
1st day of October, 2007.]
96 A. Brakes for construction equipment vehicle
2[Brakes for construction equipment vehicle. (1) Construction equipment vehicle with
hydrostatic transmission shall employ either hand or foot operated hydrostatic braking system both
for service and parking brake system acting at least on two wheels on the same axle or drum.
——————–
1. Sub-R. (9) inserted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
2. Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
81
(2) The braking system shall be of a strength capable of stopping the vehicle within the
distance specified in sub-rule (8) and of holding it at rest in all conditions, and all such brakes shall
at all times be properly conducted and maintained in efficient condition.
(3) In every construction equipment vehicle, other than those having hydrostatic
transmission, the brakes operated by any of the means of operation shall act directly upon the wheel
or at a suitable location in the power train provided that such an action does not discouple,
disengage or isolate- the braking action from the wheels.
(4) Every construction equipment vehicle which manufactured on or after the
commencement of the Motor Vehicles (Sixth Amendment) Rules, 2000, shall have a braking system
whose performance shall ^[conform to the test and stopping distance formula as specified in sub-
rule (7)].
(5) The braking system or one of the braking systems of construction equipment vehicle,
shall be so constructed and maintained that it can effectively prevent at least two wheels or drums
from revolving when the vehicle is left unattended and it shall be designed to be applied through
hand or foot or automatically when engine is not running.
(6) In the case of construction equipment vehicles with four or more than four wheels, the
service brake shall work on at least two wheels of the vehicle.
1[(7) The service braking system of the construction equipment vehicle shall be capable of
bringing the vehicle to a halt within the stopping distance as calculated by the formula given below,
when tested in unladen condition and attachment carry position at a speed corresponding to 80 per
cent, of the design maximum speed. The test shall be conducted in the forward direction of travel on
a dry level hard road in good condition and during the test the acceleration control or travel shall be
fully released and in the case of vehicle with manual gear shifting control, the top gear and the
clutch shall be engaged.]
STOPPING DISTANCE FORMULA
S < 0.15v + (V2/130),
Where S is the Stopping distance in metres,
V is the test speed corresponding to 80% of design maximum speed in Km / h.,
Control force F < 700 Newtons.
Explanation.—For the purposes of this sub-rule, “unladen” means the construction
equipment vehicle in travel mode without any load except the driver and another person for the
specific purpose of supervising the test and the instruments, if any:
Provided that while the stopping distance formula mentioned above remain unchanged, the
construction equipment using hydrostatic transmission, the brake test shall be performed by
positioning the gear change lever to the neutral position.]
——————–
1. Substituted by G.S.R. 116(E), dated 27-2-2002 (w.e.f. 27-8-2002).
82
96 B. High Speed Braking Requirements
1[ 2[High Speed Braking Requirements. For high speed braking, the following test procedure shall
be followed, namely:—
(a) in the case of Category M-l, the P type, service brake test as defined under IS: 11852-
2001—Part 3, shall be carried out in the engine connected mode at a test speed of 120 km/h
or at 80% of the design maximum speed of the vehicle, whichever is lower.
(b) the stopping distance requirements shall be according to the following formula, namely:—
S < 0.1 V + (V2/130):
where, S is the Stopping Distance in mtrs. V is the test speed in km/h, and Control force F< 500
Newtons.
Provided that this sub-rule shall be applicable in case of new vehicles yet to be type
approved after six months, and in case of already type approved vehicles, twelve months, from the
date of the commencement of the Central Motor Vehicles (Third Amendment) Rules, 2002.]
96 C. Brakes for agricultural tractor
3[Brakes for agricultural tractor. The braking system of the agricultural tractor shall conform
to IS: 12061-1994 and IS: 12207-1999, as amended from time to time.]
96 D. Braking requirements for power tillers
4[Braking requirements for power tillers. The power tillers when coupled to a trailer shall
meet the following requirements, namely:—
(i) the brake test for the power tiller coupled to a trailer shall be carried out with a gross
combination weight not exceeding 1.5 tons as declared by the manufacturer;
(ii) The brake test shall be conducted at a speed of 15 km/h to meet the stopping distance
requirement of 7.5 metres with the pedal effort not exceeding 600N;
(iii) The trailer coupled to the power tiller shall be fitted with a parking brake capable of holding
the combination on an up-slope and down-slope gradient of 12%.]
97. Brakes for trailers
(1) 5[Every trailer, other than a tractor-drawn trailer, having five hundred kilograms and more of
weight] shall have an efficient braking system which are capable of being applied when it is being
drawn,—
——————–
1. Inserted by G.S.R. 400(E) dated 31-5-2002 (w.e.f. 31-5-2002).
2. Substituted by G.S.R. 720(E), dated 10-9-2003, for the figures, letter and words “96-A High
Speed Braking Requirements” (w.e.f. 10-10-2003).
3. Inserted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
4. R. 96-D inserted by G.S.R 589(E), dated 16-9-2005 (w.e.f 16-9-2006).
5. Substituted by G.S.R. 933(E), dated 28-10-1989 (w.e.f. 28-10-1989).
83
(i) in the case of trailer having not more than two axles, to at least all the wheels of one axle; or
(ii) in the case of a trailer having more than two axles, to at least all the wheels of two axles:
Provided that the braking system shall be so constructed that it is not rendered ineffective by
the non-rotation of the engine of the drawing vehicle.
(2) The provision of sub-rule (1) shall not apply to,—
(i) any land implement drawn by a motor vehicle;
(ii) any trailer designed for use and used by a local authority for street cleansing or by the fire
service for fire fighting, which does not carry any load other than its necessary gear and
equipment;
(iii) any disabled vehicle which is being drawn by a motor vehicle in consequence of its
disablement.
1[(3) the braking system and performance requirements of the agricultural trailer in combination
with the agricultural tractor shall be in accordance with AIS: 043-2005, till the corresponding BIS
specifications are notified under the Bureau of Indian Standards, Act, 1986 ( 63 of 1986)
98. Steering gears
(1) The steering gear of every motor vehicle shall be maintained in good and sound
condition, free from back-lash exceeding 30 degrees on the steering wheel, all 2[ball joints
connecting the steering linkage,] shall be protected by rubber caps and where the connections are
secured with bolts or pins, the bolts or pins shall be effectively locked.
3[(2) The steering gear of every motor vehicle shall be so constructed as to conform to IS:
12222-1987, as amended from time to time.]
4[(3) 5[On and after 1st May, 2003], the steering effort of all motor vehicles other than three-
wheelers not fitted with steering wheel, motor cycles, 6[and invalid carriages] manufactured shall
conform to the Indian Standard IS: 11948-1999, as amended from time to time.]]
7[(4) Every heavy passenger motor vehicle manufactured after expiry of six months from the
date of commencement of the Central Motor Vehicles (Amendment) Rules, 2000 (including the
date of such commencement), shall be fitted with power steering gears.]
_______________________________________________
1. Ins. By G.S.R. 784(E), dated 12th Novemebr,2008 (w.e.f. 1-4-2009)
2. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. Sub-R. (2) substituted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
4. Sub-R.(3) substituted by G.S.R. 400(E), dated 31-5-2002 (w.e.f. 31-5-2002).
5. Substituted by G.S.R. 845(E), dated 27-12-2002, for “On and after 1st January, 2003″ (w.e.f. 27-12-2002).
6. Substituted by G.S.R. 111(E), dated 10-2-2004, for “invalid carriages and agricultural tractors” (w.e.f. 10-
8-2004).
7. Inserted by G.S.R. 65(E), dated 25-1-2000 (w.e.f. 25-1-2000).
84
1[(5) The power steering shall be fitted in,—
(a) the Category N3 multi-axle vehicles on and from 1st May, 2004; and
(b) other than multi-axle vehicles of Category N3 on and from 1st December, 2004.]
98A. 2Steering gears for construction equipment vehicles
(l) The steering system of every construction vehicle shall be maintained in good and sound
condition, with backlash not exceeding 30 degrees on the steering wheel when tested with the
engine running; ball-joints connecting the steering linkage of the mechanical steering system shall
be protected by rubber caps and where the connections are secured with bolts or pins, the bolts or
pins shall be effectively locked; in the case of hydrostatic steering system the moving parts shall be
effectively sealed and protected from dust ingress.
(2) The steering system of the construction equipment vehicle shall be adequately designed
to ensure efficient and effective control of the vehicle under all the driving conditions and shall be
so constructed as to conform to the Indian Standards IS: 12222- (1987), as modified from time to
time.
(3) The steering effort of the construction equipment vehicles during normal unladen
operation shall not exceed 11.7 kg push/pull for hydrostatic steering system and 20 kg for manual
steering wheel system when evaluated as per clauses 5.1 to 5.4 of Indian Standards IS: 11948-
(1986) as specified by the Bureau of Indian Standards.]
3[98B. Steering Gears for agricultural tractors
(1) The steering gear of agricultural tractor shall be maintained in good and sound condition,
free from backlash exceeding 30 degrees on the steering wheels. All ball joints connecting the
steering linkage shall be protected by rubber caps and where the connections are secured with bolts,
or pins, the bolts or pins shall be effectively locked.
(2) The turning circle diameter and turning circle clearance diameter of every agricultural tractor
shall conform to IS: 11859-1986, as amended from time to time.
(3) The steering effort requirement of agricultural tractor shall conform to Automotive Industry
Standard (AIS): 042 as amended from time to time, till such time the corresponding BIS standard is
notified.]
——————–
1. Sub-R (5) substituted by G.S.R. lll(E),dated 10-2-2004 (w.e.f. 10-8-2004). Earliersub- R. (5) was
inserted by G.S.R. 845(E), dated 27-12-2002 (w.e.f. 27-12-2002).
2. Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
3. Inserted by G.S.R. lll(E),dated 10-2-2004 (w.e.f. 10-8-2004).
85
1[98C. Steering gear for power tillers
The turning circle diameter and the turning clearance circle diameter of power tillers
coupled to trailers, when measured as per IS:12222:1987, as amended from time to time, shall not
exceed 10 metres.]
99. Forward and backward motion
Every 2[motor vehicle including 3[construction equipment vehicle] and agriculture tractor]
other than a motor cycle and three-wheeled invalid carriages, shall be capable of moving under its
own power 4[in the reverse direction also]:
5[Provided that power tillers with a riding attachment and power tillers coupled to trailers
shall be capable of moving under its own power in the reverse direction also.]
100. Safety glass
(1) The glass of windscreens and the windows of every motor vehicle 6[other than agricultural
tractors] shall be of safety glass:
Provided that in the case of three-wheelers and vehicles with hood and side covers, the
windows may be of 7[acrylic or plastic transparent sheet.]
Explanation.—For the purpose of this rule,—
(i) “safety glass” means glass 8[conforming to the specifications of the Bureau of Indian
Standards or any International Standards [* * *]] and so manufactured or treated that if
fractured, it does not fly or break into fragments capable of causing severe cuts;
(ii) any windscreen or window at the front of the vehicle, the inner surface of which is at an
angle 9[more than thirty degrees] to the longitudinal axis of the vehicle shall be deemed to
face to the front.
10[(2) The glass of the windscreen and rear window of every motor vehicle shall be such and shall
be maintained in such a condition that the visual transmission of light is not less than 70%. The
glasses used for side windows are such and shall be maintained in such condition that the visual
transmission of light is not less than 50%, and shall conform to Indian Standards 11[IS: 2553— Part
2—1992];
——————–
1. R. 98-C inserted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2006).
2. Substituted by G.S.R. 116(E), dated 27-2-2002, for “motor vehicle” (w.e.f. 27-8-2002).
3. Substituted by G.S.R. 111(E), dated 10-2-2004, for “construction equipment vehicle” (w.e.f.10-8-2004).
4. Substituted by G.S.R. 338(E), dated 26-3-1993, for “either forwards or backwards” (w.e.f. 26-3-1993).
5. Proviso inserted by GS.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2006).
6. Inserted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
7. Substituted by G.S.R. 338(E), dated 26-3-1993, for “acrylic transport sheet” (w.e.f. 26-3-1993).
8. Substituted by G.S.R. 933(E), dated 28-10-1989, for “approved by” (w.e.f. 28-10-1989). l. The words “as
certified by the Automobile Research Association of India, Pune” omitted by G.S.R. 214(E), dated 18-3-
1999 (w.e.f. 18-3-1999).
9. Substituted by G.S.R. 214(E), dated 18-3-1999, for “extending to thirty degrees” (w.e.f. 18-3- 1999).
10. Sub-R. (2) substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
11. Substituted by G.S.R. 214(E), dated 18-3-1999, for “IS:2253 Part 2″ (w.e.f. 18-3- 1999).
86
1[(3) The glass of the front windscreen of every motor vehicle 2[other than two wheelers and
agricultural tractors] manufactured after three years from the coming into force of the Central Motor
Vehicles (Amendment) Rules, 1993 shall be made of laminated safety glass:
3[Provided that on and from three months after the commencement of the Central Motor
Vehicles (Amendment) Rules, 1999, the glass of the front windscreen of every motor vehicle other
than two-wheelers and agricultural tractors shall be made of laminated safety glass conforming to
the Indian Standards IS: 2553—Part 2—1992.]
Explanation.—For the purpose of these sub-rules “laminated safety glass” shall mean two or
more pieces of glass held together by an intervening layer or layers of plastic materials. The
laminated safety glass will crack and break under sufficient impact, but the pieces of the glass tend
to adhere to the plastic material and do not fly, and if a hole is produced, the edges would be less
jagged than they would be in the case of an ordinary glass.
4[(3-A) The glass of the front windscreen of a construction equipment vehicle manufactured after 3
years from the date of commencement of the Central Motor Vehicles (Sixth Amendment) Rules,
2000 shall be made of laminated safety glass.]
(4) Notwithstanding anything contained in this rule if the Central Government is of the opinion that
it is necessary and expedient to do so in public interest, it may, by order published in the Official
Gazette, exempt 5[any motor vehicle including construction equipment vehicle] for use by any
person, from the provisions of this rule.]
101. Windscreen wiper
6[Windscreen wiper. (1) An efficient power operated 7[* * *] windscreen wiper shall be
fitted to every motor vehicle having a windscreen, other than three-wheeled invalid carriage 8[and
motor cycles].
(2) One year from the date of commencement of Central Motor Vehicles (Amendment)
Rules, 1993, 9[all motor vehicles other than three-wheelers, motor cycles and invalid
carriages 10[manufactured on and after 1st January, 2003 in respect of Category Ml vehicles, and in
respect of other vehicles, on and after 1st May, 2003], having a wind screen shall be fitted
____________________________________________
1. Inserted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
2. Substituted by G.S.R. 214(E), dated 18-3-1999, for “other than agricultural tractors” (w.e.f. 18-
3-1999).
3. Inserted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
4. Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
5. Substituted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
6. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
7. The words “or foot operated” omitted by G.S.R. 214(E), dated 18-3-1999 (w e I” 18-3-1999).
8. Substituted by G.S.R. 589(E), dated 16-9-2005, for “motor cycles and three-wheelers of engine
capacity not exceeding 500 cc” (w.e.f. 1-4-2006).
9. Substituted by G.S.R. 400(E), dated 31-5-2002 (w.e.f. 31-5-2002).
10. Substituted by G.S.R. 845(E), dated 27-12-2002, for “manufactured on and after 1st January,
2003″ (w.e.f. 27-12-2002).
87
with a wind screen wiping system which shall conform to the requirements laid down in the
following standards, as amended from time to time, till such time the corresponding Bureau of
Indian Standards specifications are notified:
(i) A1S 019/2001, in the case of M-l category of vehicles
(ii) AIS 011/2001, in the case of other vehicles.] 1[(2-A) All construction equipment vehicles
having windscreen shall be fitted with an efficient power operated windscreen wiping system.
The windscreen wiping system shall conform to the requirements of the standards as may be
specified from time to time under these rules.] 2[* * *]
3[102. Signalling devices, direction indicators and stop lights
4[(1) The signal to turn to the right or to the left shall be given by electrically operated
direction indicator lamps on all motor vehicles including construction equipment vehicles. Every
construction equipment vehicle shall be fitted and maintained so that the following conditions are
met, namely:—
(i) The direction indicator lamps shall be of amber colour which is illuminated to indicate the
intention to turn, by a light flashing at the rate of not less than 60 and not more than 120
flashes per minute.
(ii) The light emitted by the lamp when in operation shall be clearly visible from both front and
rear of the vehicle.
(iii) The minimum illuminated area of each direction indicator shall be 60 square centimeters:
Provided that nothing contained in this sub-rule shall apply to L1 category of motor cycles.]
5[(2) On all vehicles other than motor cycles, 6[the intention to stop the vehicle (other than
construction equipment vehicle having hydrostatic brakes)] shall be indicated by two electrical stop
lamps which shall be red in colour and shall be fitted one on each left and right-hand sides at the
rear of the vehicle. The stop lamps shall light up on the actuation of the service brake control. In the
case of motor cycle, the intention to stop the vehicle shall be indicated by one stop lamp at the rear
which shall light up on the actuation of the control operating the brakes on the rear wheels.]
(3) One year from the date of commencement of the Central Motor Vehicles (Amendment) Rules,
1993, the stop lamp of every motor cycle shall be so designed and fitted that it will light up on
actuation of any of the controls which actuate the brakes on any wheel.]
1. Sub-R. (2-A) substituted by G.S.R. 116(E), dated 27-2-2002 (w.e.f. 27-8-2002).Earlier sub-R. (2-
A) was inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
2. Sub-R. (3) omitted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
3. Substituted by G.S.R. 33S(E), dated 26-3-1993 (w.e.f. 26-3-1993).
4. Sub-R. (1) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 14-2006).
5. Sub-R. (2) substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
6. Substituted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
88
103. Position of the indicator
(1) A direction indicator shall be fitted and every direction indicator shall be so designed
and fitted that 1[the driver of the vehicle including a construction equipment vehicle] when in his
driving seat is aware that it is operating correctly.
2[(2) One year from the date of commencement of the Central Motor Vehicles (Amendment)
Rules, 1993, 1[every motor vehicle including a construction equipment vehicle] other than 3[* * *]
motor cycles shall be equipped with such a device that when the vehicle is in an immobilized
condition all the direction indicators flash together giving hazard warning to other road users.]
104. Fitment of reflectors
4[Fitment of reflectors. 5[(1) Every motor vehicle manufactured on and after the 1st day of
April, 2006, including trailers and semi-trailers, other than three-wheelers and motor cycles shall be
fitted with two red reflectors, one each on both sides at their rear. Every motor cycle shall be fitted
with at least one red reflex reflector at the rear:
6[Provided that in respect of the vehicles of-
(ii) category NI and category N2, 3.5 tonnes and above but less then 7.5
tonnes Gross Vehicle Weight, manufactured on and after 1st day of April, 2009,
shall be affixed at the front with a white reflective tape and at the rear with a red
reflective tape running across the width of the body and the tape affixed at front
and rear shall be not less than 20 mm width and shall conform to the requirement
of Annexures 4, 5 and 6 of AIS: 090-2005 till the corresponding BIS specifications
are notified under the Bureau of Indian Standards Act, 1986 (63 of 1986).
(iii) categoryN3 and categoryN2, 7.5tonnes and above Gross Vehicle Weight
manufactured on and after 1st day of April, 2009, shall be affixed at the front with a
white reflective tape running across the width of the body and the tape affixed at
the front shall not be less than 50 min width and shall conform to the requirement of
Annexures 4, 5 and 6 of AIS: 090- 2005 till the corresponding BIS specifications are
notified under the Bureau of Indian Standards Act, 1986 (63 of 1986).
________________________
1. Substituted by G.S.R. 116(E), dated 27-2-2002, for “the driver of the vehicle” and “every motor
vehicle”, respectively (w.e.f. 27-8-2002).
2. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. The words “three wheelers of engine capacity not exceeding 500 cc and” omitted by G.S.R.
589(E), dated 16-9-2005 (w.e.f. 1-4-2006).
4. Substituted by G.S.R 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
5. Sub-R. (1) and the proviso substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
6. Subs by G.S.R. 784 (E), dated 12th November,2008 (w.e.f. 12-11-2008)
89
(iv) category N3 including trailers or semi-trailers and category N2,) 7.5 tonnes
and above GVW along with trailers or semi-trailers, manufactured on and after 1st
day of April, 2009, shall be affixed with reflective contour marking at the rear
and side in accordance with AIS: 090-2005 till the corresponding BIS specifications
are notified under the Bureau of Indian Standards Act, 1986 (63 of 1986).
(v) category M2 and M3, manufactured on and after 1st October 2009, shall
be.affixed at the front with white reflective.tape and at the rear with red reflective
tape running acr.oss the width of the body and the sides of M3 category vehicles
shall be affixed with yellow reflective tape running across the length of the body
but tapes so affixed shall not be less than 50 mm width and shall conform to
Annexures 4, 5 and 6 of AIS:090-2005, till the corresponding BIS specifications are
notified under the 'Bureau of Indian Standards Act, 1986 (63 of 1986).]]
(2) Every goods carriage vehicle including trailers and semi-trailers other than three wheeler 1[* *
*] shall be fitted with two white reflectors one each at the extreme right and left bottom corners in
the front of the vehicle and facing to the front. The reflecting area of each reflector shall not be less
than 28.5 sq. centimetres, in the case of vehicles with overall length of more than 6 metres, and not
less than 7 sq. centimetres in case of other vehicles.]
2[(3) All trailers including semi-trailers, other than those drawn by three-wheeled tractors 1[* * *]
shall be fitted with the following reflex reflectors, namely,—
(i) two white reflex reflectors in the front, one each at the right and left corners at a height not
exceeding 1500 mm above the ground,
(ii) two red reflex reflectors in the rear, one each at the right and left corners at a height not
exceeding 1500 mm above the ground, and
(iii) the area of the reflectors referred to above shall not be less than 28.5 sq. cm. in the case of
trailers with overall length exceeding 6 metres and shall not be less than 7 sq. cm. in case of
other trailers.]
3[(4) On and after expiry of one year from the date of commencement of the Central Motor Vehicles
(Amendment) Rules, 1999, the reflectors referred to in this rule and in rule 110 shall be of reflex
type conforming to 4[AIS:057:2005 till the corresponding BIS specifications are notified under the
Bureau of Indian Standards Act, 1986 (63 of 1986)].
——————-
1. The words “of engine capacity not exceeding 500 cc” omitted by G.S.R. 589(E), dated 16-9-
2005 (w.e.f. 1-4-2006).
2. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
3. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999). Earlier sub-R. (4) was
substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
4. Substituted by G.S.R. 589(E), dated 16-9-2005, for “the Indian Standards IS:8339— 1993
specified by the Bureau of Indian Standards” (w.e.f. 1-4-2006).
90
1[(5) On and from the date of commencement of the Central Motor Vehicles Rules, 1993, every
motor vehicle and trailer of length exceeding 6 metres shall be fitted with two amber coloured
reflex reflectors on each left hand and right hand of the vehicle, one set as close to the front end as
possible and the other set as close to the rear end as possible. The height of the side reflectors above
the ground shall not be more than 1500 mm. The area of each reflector shall not be less than 28.5
sq. cm.:
Provided that in case the distance between the two side reflectors is more than 3 metres,
additional intermediate side reflectors shall be fitted so that the distance between any adjacent side
reflector is not more than 3 metres.]
2[104A. Fitment of reflectors on construction equipment vehicles
All construction equipment vehicles shall be fitted with—
(i) two white reflex reflectors in the front of the vehicle on each side and visible to oncoming
vehicles from the front at night;
(ii) two red reflectors in the rear of the vehicle, one each at right and left corners, at a height not
exceeding 1500 mm above the ground in the case of unobstructed vision from the rear and
the implement or device shall not obstruct the visibility of the reflectors to the following
vehicle;
(iii) two sets of amber coloured side reflex reflectors, one each on left hand and right hand sides
of the vehicle, one set as close to the front end and the other set as close to the rear end as
possible to the basic machine without attachments and if the distance between the two amber
side reflex reflectors is more than 3 metres, additional intermediate amber side reflex
reflectors shall be fitted so that the distance between any adjacent amber side reflex reflector
is not more than 3 metres:
3[Provided that the fitment of reflex reflectors on the implements such as booms of cranes
and anus of shovels, shall not be mandatory. However, wherever possible the fitment of these
reflectors may be done considering the working environment/nature of these machines in the fields;]
(iv) the reflecting area of each reflex reflector shall not be less than 28.5 sq. cms;
(v) the construction equipment vehicle shall be fitted with a retro-reflective tape or
retroreflective paint of not less than 20 millimeters width, running across the width of the
body at the front and rear, and the colour of the reflective tape or reflective paint shall be
white at the front and red at the rear;
(vi) the reflectors referred to in this sub-rule, shall be of reflex type conforming to Indian
Standards IS: 8339 specified by the Bureau of Indian Standards;
——————–
1. Substituted by G.S.R 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
2. Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
3. Substituted by G.S.R. 116(E), dated 27-2-2002, for the proviso (w.e.f. 27-8-2002).
91
(vii) the retro-reflective tape and paint shall be as per clause 801 and 803 of Ministry of Surface
Transport (Roads Wing) specifications for Road and Bridge works (3rd Revision, 1995) as
amended from time to time.]
1[104B. Fitment of reflectors for agricultural tractors
(1) Every agricultural tractor manufactured on and after the 1st day of April, 2006 shall be
fitted with two non-triangular red reflectors of not less than 7 sq. cm reflecting area one each on
both sides at the rear.
(2) The reflectors referred in sub-rule (1) of this rule shall be of the reflex type conforming
to AIS:057:2005 till the corresponding BIS specifications are notified under the Bureau of Indian
Standards Act, 1986 (63 of 1986).
104C. Fitment of reflectors on power tillers
(1) On and from one year from the date of commencement of the Central Motor Vehicles
(Fifth Amendment) Rules, 2005, every power tiller shall be fitted with two white reflex reflectors of
not less than 7 sq. cm reflecting area in the front of the vehicle one on each side and visible to
oncoming vehicles from the front at night, conforming to AIS:057:2005 till corresponding BIS
specifications are notified under the Bureau of Indian Standards Act, 1986 (63 of 1986).
(2) In the case of trailers attached to power tillers, two red reflectors of not less than 7 sq.cm
reflecting area in the rear side, one each at right and left corners, at a height not exceeding 1500 mm
above the ground shall also be fitted.]
105. Lamps
2[(1) Save as hereinafter provided, every motor vehicle, while being driven in a public place,
during the period half an hour after sunset and at any time when there is no sufficient light, shall be
lit with the following lamps which shall render clearly discernible persons and vehicles on the road
at a distance of one hundred and fifty five metres ahead:—
(a) in the case of motor vehicle other than three-wheelers, three-wheeled invalid carriages and
motorcycles, two or four head lamps;
(b) in the case of motor cycles, three-wheelers and three-wheeled invalid carriages one or two
head lamps;
(c) in the case of a side car attached to a motor cycle one lamp showing a white light to the
front;]
(d) in the case of construction equipment vehicle, two or four lamps showing to the front white
light visible from a distance of one hundred and fifty five metres ahead.]
-------------------
1. R. 104-B inserted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
2. Sub-R. (1) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 1-4-2006).
92
(2) Every such motor vehicle other than a 1[* * *] three-wheeler shall also carry—
(i) 2[two lamps (hereinafter referred to as the rear lamp) showing to the rear a red light visible
in the rear from a distance of one hundred and fifty-five metres; and in the case of a motor
cycle one lamp showing a red light to the rear visible from a distance of seventy five
metres]; and
(ii) lamp, which may be the rear lamp or some other device, illuminating with a white light the
whole of the registration mark exhibited 3[4[on the rear of the vehicle including construction
equipment vehicle], and on the side in the case of construction equipment vehicle] so as to
render it legible from a distance of fifteen metres to the rear:
Provided that when a motor vehicle is drawing another vehicle or vehicles and the distance
between such vehicles does not exceed 1.5 metres, it shall be sufficient if the last drawn vehicle
carries a rear lamp or a lamp illuminating the rear registration mark:
5[Provided further that every construction equipment vehicle shall also carry two lamps
showing to the rear red lights visible in the rear from a distance of one hundred and fifty five
metres.]
6[(3) On and from the commencement of the Central Motor Vehicles (Amendment) Rules, 1993, all
the obligatory front head lamps of a motor vehicle other than motor cycles shall be as nearly as
possible of the same power and fixed at a height as specified in Indian Standards 40[IS: 8415—
1977] (clause 4.1):
Provided that in the case of four-wheel drive cross country vehicles, the maximum height of
the said front head lamps may be as per limits specified in Indian Standards 40[IS: 8415—1977]
(clause 4.1.1):
7[* * *]
Provided further that on and from the commencement of the Central Motor Vehicles
(Amendment) Rules, 1993, all vehicles other than three-wheelers of engine capacity less than 500
cc, motor cycles and three-wheeled invalid carriages manufactured shall be fitted with two rear
lamps showing red light to the rear.]
__________________________________________________________
1. The words “a motor cycle and” omitted by G.S.R. 214(E), dated 18-3-1999 (w e I 18-3-1999).
2. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
3. Substituted by G.S.R. 642(E), dated 28-7-2000, for “on the rear of the vehicle” (w.e.f. 28-7-2000).
4. Substituted by G.S.R. 116(E), dated 27-2-2002, for “on the rear of the vehicle” (w.e.f. 27-8-2002).
5. Substituted by G.S.R. 642(E), dated 28-7-2000, for “on the rear of the vehicle” (w.e.f. 28-7-2000).
6. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999.
7. Proviso omitted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
93
1[(3-A) On and from the commencement of the Central Motor Vehicles (Sixth Amendment)
Rules, 2000, all the obligatory front head lamps of a construction equipment vehicle shall be as
nearly as possible of the same power and fixed at a height so that front visibility is maintained and
farthermost point of equipment/attachment is clearly seen by on-coming traffic]
(4) The rear lamp shall be fixed either on the centre line of the vehicle or to the right hand
side, and save in the case of a transport vehicle, at a height of not exceeding one metre above the
ground:
2[3***]
(5) In the case of a transport vehicle/ the rear light may be fixed at such level as may be
necessary to illuminate the registration mark.
(6) Every heavy goods carriage 4[including trailers] shall be fitted with a red indicator lamp of size
of thirty centimetres by ten centimetres on the extreme rear most body cross beam and in the case of
a vehicle not constructed with body in the rear, the indicator lamp shall be fitted near the right rear
light above the rear number plate:
5[Provided that every construction equipment vehicle of an unconventiona I or extraordinary
type in travel mode shall be fitted or installed with a red indicator lamp of size of not less than 100
square centimetres on the extreme rearmost point of the body.]
6[(7) On and from the date of commencement of the Central Motor Vehicles (Amendment)
Rules, 1999, every motor vehicle manufactured shall be fitted with at least one lamp which shall
automatically be operated, throwing a white light to the rear, when the vehicle is being driven in the
reverse gear.]
7[(8) In the case of vehicles, other than three-wheelers of engine capacity not exceeding 500
CC, which are attached with trailers, all the lamps required to be fitted on the rear of the vehicle
shall be fitted at the rear of the trailer.]
8[(8-A) On the commencement of the Central Motor Vehicles (Sixth Amendment) Rules,
2000, every construction equipment vehicle shall be fitted with two lamps at the rear throwing light
to the rear when the vehicle is being driven in the reverse gear and there shall also be an audible
warning system operating when the vehicle is being driven in the reverse gear, the audible warning
system and the light being automatically operated when the vehicle is in reverse gear.]
___________________________________________________
1. Inserted by G.S.R 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
2. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. Proviso omitted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
4. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
5. Added by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
6. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999). Earlier sub-R. (7) was
inserted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
7. Inserted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
8. Added by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000). Previously inserted by G.S.R.
214(E), dated 18-3-1999. [There seems to be some confusion/mis take in the language of CI.
13(/) of G.S.R. 214(E), dated 18-3-1999 and CI. 13(g) of G.S.R. 642(E), dated 28-7-2000]
94
106. Deflection of lights
(1) No lamp showing a light to the front shall be used on 1[any motor vehicle including
construction equipment vehicle] (whether fitted with single or dual head lamp) unless such lamp is
so constructed, fitted and maintained that the beam of light emitted therefrom—
2[(2) is permanently deflected downwards to such an extent that it is not capable of dazzling any
person whose eye position is,—
(A) at a distance of 8 metres from the front of lamp,
(B) at a distance of 0.5 metre to the right side of the lamps, i.e., fitted at right extreme of the
vehicle, from the right edge of the lamp, and
(C) at a height of 1.5 metres from the supporting plane of the vehicle:
3[(a)***]
(b) is capable of being deflected downwards by the driver in such manner as to render it
incapable of dazzling any such person in the circumstances aforesaid;
(c) is capable of being extinguished by the operation of a device which at the same time
causes a beam of light to be emitted from the lamp which complies with the
provision of clause (a);
(d) is capable of being extinguished by the operation of a device which at the same time
either deflects the beam of light from another lamp downwards or both downwards
and to the left in such manner as to render it incapable of dazzling any person in the
circumstances aforesaid, or brings into or leaves in operation a lamp which complies
with the provisions of clause (a).
4[* * *]
5[(2)] The provisions of sub-rule (1) shall not apply to any lamp fitted with an electric bulb,
if the power of the bulb does not exceed 7 watts and the lamp is fitted with a frosted glass or other
material which has the effect of diffusing the light.
6[107. Top lights
Every goods vehicle including trailer and semi-trailer other than three-wheelers and vehicles
with overall width not exceeding 2.1 metres shall be fitted with two white lights at the
——————–
1. Substituted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
2. Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
3. Proviso to CI. (a) omitted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
4. Sub-R. (2) omitted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
5. Sub-R (3) renumbered as sub-R (2) by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
6. Substituted by G.S.R 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
95
top right and left comers 1[showing white light to the front] and two red lights at the top right
and 1[showing red light to the rear]. The lights shall remain lit when the vehicle is kept stationary on
the road during night and at the time of poor visibility:
Provided that in the case of goods carriage without a full body in the rear, provision for
fitting of the top light at the rear shall not be necessary.]
107A. 2[Implement lights for construction equipment vehicle
Construction equipment vehicle having implements with front overhang greater than 60% of
wheelbase shall be fixed with additional implement light of amber colour at a location nearest to the
extreme edge of the implement without affecting the functions of showing light in all directions and
where the implement is more than 3 metres in length, additional amber coloured lamps shall be
fixed at a distance of not exceeding 3 metres for the entire length of the implement:
Provided that in case of rear overhang the additional implement lights shall be in red
colour.]
3[108. Use of red, white or blue light
(1) No motor vehicle shall show a red light to the front or light other than red to rear:
Provided that the provisions of tills rule shall not apply to—
(i) the internal lighting of the vehicle; or
(ii) the amber light, if displayed by any direction indicator or top light or as top light used on
vehicle for operating within the premises like airports, ports without going outside the said
premises on to public roads;
(iii) a vehicle carrying high dignitaries as specified by the Central Government or the State
Government, as the case may be, from time to time;
(iv) the blinker type of red light with purple glass fitted to an ambulance van used for carrying
patients; or
(v) to a vehicle having a lamp fitted with an electrical bulb, if the power of the bulb does not
exceed seven watts and the lamp is fitted with frosted glass or any other material which has
the effect of diffusing the light;
(vi) white light illuminating the rear number plate;
——————-
1. Substituted by G.S.R. 214(E), dated 18-3-1999 (w.e.f. 18-3-1999).
2. Inserted by G.S.R. 642CE), dated 28-7-2000 (w.e.f. 28-7-2000).
3. Substituted by G.S.R. 400(E), dated 31-5-2002 (w.e.f. 31-5-2002).
96
(vii) white light used while reversing;
(viii) plough light provided in agricultural tractors for illuminating the implement's working area
on the ground in agricultural field operations.
(2) Use of blue light with flasher shall be determined and notified by the State Governments at their
discretion.
(3) Use of blue light with or without flasher shall be permitted as top light on vehicles escorting
high dignitaries entitled to the use of red light.
(4) Use of multi-coloured red, blue and white light shall be permitted only on vehicles specifically
designated for emergency duties and shall be specifically specified by State Governments.
(5) The State Government shall inform the Central Government regarding publication of
notifications issued by the concerned State Government under sub-rule (2) and under clause (e) of
the Notification No. S.O. 52(E), dated 11th January, 2002, published in the Gazette of India,
Ministry of Road Transport and Highways, regarding use of red light on top of vehicle being used
by dignitaries.
(6) In case vehicle is not carrying dignitaries, red or blue light, as the case may be, light shall not be
used and be covered by black cover.]
Previous and next
← Rule 90Additional conditions for national permit The national permit issued under subsection (12) of section 88 shall be subject to the following additional conditions, namelyRule 108A →Use of red or white light on construction equipment vehicles No construction equipment vehicle shall show a red light to the front or light other than red to the rear: Provided that the provision of this rule shall not apply to
Questions people ask
Is rule 93B of THE CENTRAL MOTOR VEHICLES RULES, 1989 still in force?
No repeal of the CENTRAL MOTOR VEHICLES RULES, 1989 is recorded.