LawGrids logoLAWGRIDS.ORG

Appendix, Punjab Factories Rules 1952: APPENDIX

Punjab Factories Rules 1952 - Appendix

Text of appendix

APPENDIX

APPENDIX CAUTIONARY NOTICE Insecticides and pesticides 1. Chemicals handled in this plant are poisonous substances. 2. Smoking, eating food or drinking, chewing tobacco in this area is prohibited. No food stuff or drink shall be brought in this area. 3. Some of these chemicals may be absorbed through skin and may cause poisoning. 4. A good wash shall be taken before meals. 5. A good bath shall be taken at the end of this shift. 6. Protective clothing and equipment supplied shall be used while working in this area. 7. Containers of pesticides shall not be used for keeping food stuffs. 8. Spillage of the chemicals on any part of the body or on the floor or work- bench shall be immediately washed away with water. 9. Clothing contaminated sue to splashing shall be removed immediately. 10. Scrupulous cleanliness shall be maintained in this area. 11. Do not handle pesticides with bare hands, use scoops provided with handle. 12. In case of sickness like nausea, vomiting, giddiness, the manager should be informed who will make necessary arrangements for treatment. 13. All workers shall report for the prescribed medical tests regularly to protect their own health. Schedule – XXV Manufacture of Rayon by viscose process 1. Definitions - For the purpose of this schedule - (a) ”approved” means approved for the time being in writing by the Chief Inspector; (b) ”breathing apparatus” means a helmet or face piece with necessary connections by means of which the person using it in a poisonous, asphyxiating or irritant atmosphere breathes unpolluted air; or any other approved apparatus; (c) ”churn” means the vessel in which alkali cellulose pulp is treated with carbon disulphide; (d) ”dumping” means transfer of cellulose xanthate from a dry churn to a dissolver; (e) ”efficient exhaust draught” means localised ventilation by mechanical means for the removal of any gas or vapour, so as to prevent it from escaping into the air of any place in which work is carried on. No draught shall be deemed to be efficient if it fails to control effectively any gas or vapour generated at the point where such gas or fume originates; (f) ”fume process” means any process in which carbon disulphide or hydrogen sulphide is produced, used or given off; (g) ”life belt” means a belt made of leather or other suitable material which can be securely fastened round the body with a suitable length of rope attached to it, each of which is sufficiently strong to sustain the weight of a man; (h) ”protective equipment” means apron, goggles, face shields, footwear, gloves and overalls made of suitable materials. 2. Ventilation - (1) In all workrooms where a fume process is carried on, adequate ventilation by natural or mechanical means shall be provided so as to control, in association with other control measures, the concentration of carbon-di-sulphide and hydrogen sulphide in the air of every work environment within the permissible limits. (2) Notwithstanding the requirements in sub-paragraph (1) an efficient exhaust draught shall be provided and maintained to control the concentration of carbon-di- sulphide and hydrogen sulphide in the air at the following locations :- (a) dumping hoppers of dry churns; (b) spinning machines; (c) trio rollers and cutters used in steple fibre spinning; (d) gydro-extractors for yarn cakes; (e) after treatment processes; and (f) spin baths. (3) In so far as the spinning machines and trio rollers and cutters used in staple fibre spinning are concerned, they shall be, for the purpose of ensuring the effectiveness of the exhaust draft to be provided as required in sub-paragraph (1), enclosed as fully as practicable and provided with suitable shutters in sections to enable the required operations to be carried out without giving rise to undue quantities of carbon-di-dulphide escaping to the work environment. (4) No dry churn shall be opened after completion of reaction without initially exhausting the residual vapours of carbon-di-sulphide by operation of a suitable and efficient arrangement for exhausting the vapours which shall be continued to be operated as long as the churn is kept opened. (5) Whenever any ventilation apparatus normally required for the purpose of meeting the requirements in sub-paragraphs (2), (3), and (4) is ineffective, fails, or is stopped for any purpose whatsoever, all persons shall be required to leave the work areas where the equipment or processes specified in the above said sub-paragraphs are in use, as soon as possible, and in any case not later than 15 minutes after such an occurrence. (6) (a) All ventilating systems provided for the purposes as required in sub- paragraphs (2), (3) and (4) shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once In every period of 12 months. Any defects found by such examinations or test shall be rectified forthwith. (b) A register containing particulars of such examinations and tests, and the state of the systems and the repairs or alterations (if any) found to be necessary shall be kept and shall be available for inspection by an Inspector. 3. Waste from spinning machines- Waste yarn from the spinning machines shall be deposited in suitable containers provided with close fitting covers. Such waste shall be disposed off as quickly as possible after decontamination. 4. Lining of dry churns - The inside surface of all dry churns shall be coated with a non- sticky paint so that cellulose xanthate will not stick to the surface of the churn. Such coating shall be maintained in good condition. 5. Air monitoring - (1) To ensure the effectiveness of the control measures, monitoring of carbon-di- sulphide and hydrogen sulphide in air shall be carried out once atleast in every shift and the record of the results so obtained shall be entered in a register specially maintained for the purposes. (2) For the purpose of the requirement in sub-paragraph (1), instantaneous gas detector tubes shall not be used. Samples shall be collected over duration of not less than 10 minutes and analyzed by an approved method. The locations where such monitoring is to be done shall be as directed by the Inspector. (3) If the concentration of either carbon disulphide or hydrogen sulphide exceeds the permissible limits for such vapour or gas as laid down in Rule 123A, suitable steps shall be taken for controlling the concentrations in air of such contaminants. A report of such occurrences shall be sent to the Chief Inspector forthwith. 6. Prohibition to remain in fume process room - No person during his intervals for meal, or rest shall remain in any room wherein fume process is carried on. 7. Prohibition relating to employment of young persons - No young person shall be employed or permitted to work in any fume process or in any room in which any such process is carried on. 8. Protective equipment - (1) the occupier shall provide and maintain in good condition protective equipment as specified in the Table for use of persons employed in the processes referred to therein. Table No. Process Protective equipment 1. Dumping Overalls, face-shields, gloves and footwear – all made of suitable material 2 .Spinning Suitable aprons, gloves and footwear 3 Process involving or likely to involve contact with viscose solution Suitable gloves and footwear 4 .Handling of sulphur Suitable chemical goggles Any other process involving contact with hazardous chemicals Protective equipment as may be directed by the Chief Inspector by an order in writing (2) A suitable room, rooms or lockers shall be provided exclusively for the storage of all protective equipment supplied to workers and no such equipment shall be stored at any place other than the room, rooms or lockers so provided. 9. Breathing apparatus - (1)There shall be provided in every factory where fume process is carried on, sufficient supply of - (a) breathing apparatus, (b) oxygen and a suitable appliances for its administration, and (c) life belts. (2) (a) The breathing apparatus and other appliances referred to in sub- paragraph (1) shall be maintained in good condition and kept in appropriate locations so as to be readily available. (b) The breathing apparatus and other appliances referred to in clauses (a) and (b) of sub-paragraph (1) shall be cleaned and disinfected at suitable intervals and thoroughly inspected once every month by a responsible person. (c) A record of the maintenance of the condition of the breathing apparatus and other appliances referred to in sub-clause (1) shall be entered in a register provided for that purpose which shall be readily available for inspection by an Inspector. (3) Sufficient number of workers shall be trained and periodically retrained in the use of breathing apparatus and administering artificial respiration so that at least 2 such trained persons would be available during all the working hours in each room in which fume process is carried on. (4) Breathing apparatus shall be kept properly labeled in clean, dry, light-proof cabinets and if liable to be affected by fumes, shall be protected by placing them in suitable containers. (5) No person shall be employed to perform any work for which breathing apparatus is necessary to be provided under sub-paragraph (1) unless he has been fully instructed in the proper use of that equipment. (6) No breathing apparatus provided in pursuance of sub-paragraph (1) which has been worn by a person shall be worn by another person shall be worn by another person unless it has been thoroughly cleaned and disinfected since last being worn and the person has been fully instructed in the proper use of that equipment. 10. Electric fittings - All electric fittings in any room in which carbon-di-sulphide is produced, used or given off or is likely to be given off into the work environment, other than a spinning room, shall be of flame-proof construction and all electric conductors shall either be enclosed in metal conduits or be lead-sheathed. 11. Prohibition relating to smoking, etc. - No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in a room in which fume process is carried on. A notice in the language understood by the majority of the workers shall be posted at prominent locations in the plant prohibiting smoking and carrying of matches, fire or naked light or other means of producing naked light or spark into such rooms. Provided that fire, naked light or other means of producing a naked light of spark may be carried on in such room only when required for the purposes of the process itself under the direction of a responsible person. 12. Washing and bathing facilities - (1)There shall be provided and maintained in a clean state and in good repair for the use of all workers employed and in the processes covered by the schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 25 persons employed. (2) The washing places shall have standpipes placed at intervals of not less than one meter. (3) Not less than one half of the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable material shall be provided. Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 13. Rest Room - (1) A rest room shall be provided for the workers engaged in doffing operations of filament yarn spinning process. (2) Such rest room shall be provided with fresh air supply and adequate seating arrangement. 14. Cautionary notice and instructions - (1) the following cautionary notice shall be prominently displayed in each fume process room. Cautionary Notice I. Carbon disulphide (CS2) and Hydrogen Sulphide (H2S) which may be present in this room are hazardous to health. II. Follow safety instructions. III. Use protective equipment and breathing apparatus as and when required. IV. Smoking is strictly prohibited in this area.” This notice shall be in a language understood by the majority of the workers and displayed where it can be easily and conveniently read. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so displayed. (2) Arrangements shall be made to instruct each worker employed in any room in which a fume process is carried on regarding the health hazards connected with their work and the preventive measures and methods to protect themselves. Such instructions shall be given on his first employment and repeated periodically. (3) Simple and special instructions shall be framed to ensure that effective measures will be carried out in case of emergency involving escape of carbon- di-sulphide and hydrogen sulphide. Those instructions shall be displayed in the concerned areas and workers shall be instructed and trained in the actions to be taken in such emergencies. 15. Medical facilities and records of examinations and tests - (1) the occupier of every factory to which this schedule applies, shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of such examinations carried out by the medical practitioner shall be maintained in a separate, register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 16. Medical examination by certifying Surgeon - (1) every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examinations shall include skin test for dermatitis and no worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in a manganese process shall be re-examined by a Certifying Surgeon at least once in every three calendar months and such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manger of the factory. The record of each examination carried out under sub-paragraph (1) and (2) including the nature and the results of these test, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon , in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 17. Exemptions - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for the protection of the workers in the factory, the Chief Inspector may be a certificate in writing which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Schedule – XXVI Highly Flammable Liquids and Flammable Compressed Gases 1. Application - These rules will be applicable to all factories where highly flammable liquids or flammable compressed gases are manufactured, stored, handled or used. 2. Definition - For the purpose of this schedule – (a) ”highly flammable liquid” means any liquid including its solution, emulsion or suspension which when tested in a manner specified by sections 14 and 15 of the Petroleum Act, 1934, (30 of 1934) gives off flammable vapours at a temperature less than 32 degree centigrade; (b) ”flammable compressed gas” means flammable compressed gas as defined in section 2 of the Static and Mobile Pressure Vessels (Unfired) Rules 1981 framed under the Explosive Act, 1884. 3. Storage - (1) Every flammable liquid or flammable compressed gas used in every factory shall be stored in suitable fixed storage tank, or in suitable closed vessel located in a safe position under the ground, in the open or in a store room of adequate fire resistant construction. (2) Except as necessary for use, operation or maintenance, every vessel or tank which contains or had contained highly flammable liquid or flammable compressed gas shall be always kept closed and all reasonably practicable steps shall be taken to contain or immediately drain off to a suitable container any spill or leak that may occur. (3) Every container, vessel, tank, cylinder, or store room used for storing highly flammable liquid or flammable compressed gas shall be clearly and in bold letters marked “Danger-Highly Flammable Liquid” or “Danger-Flammable Compressed Gas”. 4. Enclosed Systems for Conveying Highly Flammable Liquids - Wherever it is reasonably practicable, highly flammable liquids shall be conveyed within a factory in totally enclosed systems consisting of pipe lines, pumps and similar appliances from the storage tank or vessel to the point of use. Such enclosed systems shall be so designed, installed, operated and maintained as to avoid leakage or the risk of spilling. 5. Preventing Formation of Flammable Mixture with Air - Wherever there is a possibility for leakage or spill of highly flammable liquid or flammable compressed gas from any equipment, pipe line, valve, joint or other part of a system, all practicable measures shall be taken to contain, drain off or dilute such spills or leakage as to prevent formation of flammable mixture with air. 6. Prevention of Ignition - (1) In every room, work place or other location where highly flammable liquid or flammable combustible gas is stored, conveyed, handled or used or where there is danger of fire or explosion from accumulation of highly flammable liquid or flammable compressed gas in air, all practicable measures shall be taken to exclude the sources of ignition. Such precautions shall include the following: (a) All electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition; (b) Effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent; (c) no person shall wear or be allowed to wear any foot wear having iron or steel nails or any other exposed ferrous materials which is likely to cause sparks by friction; (d) Smoking, lighting or carrying of matches, lighters or smoking materials shall be prohibited; (e) Transmission belts with iron fasteners shall not be used; and (f) all other precautions, as are reasonably practicable, shall be taken to prevent initiation of ignition from all other possible sources such as open flames, frictional sparks, overheated surfaces of machinery or plant, chemical or physical-chemical reaction and radiant heat. 7. Prohibition of smoking - No person shall smoke in any place where highly flammable liquid or flammable compressed gas is present in circumstances that smoking would give a risk of life. The occupier shall take all practicable measures to ensure compliance with this requirement including display of a bold notice indicating prohibition of smoking at every place where this requirement applies. 8. Fire Fighting - In every factory where highly flammable liquid or flammable compressed gas is manufactured, stored, handled or used, appropriate and adequate means of fighting a fire shall be provided. The adequacy and suitability of such means which expression includes the fixed and portable fire extinguishing systems, extinguishing material, procedures and the process of fire fighting, shall be to the standards and levels prescribed by the Indian Standards applicable, and in any case not inferior to the stipulations under Rule 66 of Punjab Factory Rules,1952. 9. Exemptions - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for the protection of the workers in the factory, the Chief Inspector may be a certificate in writing which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. http://dgfasli.nic.in/html/modelrules/modelrules1/part2.htm� http://dgfasli.nic.in/html/modelrules/modelrules1/sch_26.htm#_top#_top� http://dgfasli.nic.in/html/modelrules/modelrules1/sch_27.htm� http://dgfasli.nic.in/html/modelrules/modelrules1/part2.htm� http://dgfasli.nic.in/html/modelrules/modelrules1/sch_26.htm� http://dgfasli.nic.in/html/modelrules/modelrules1/sch_27.htm� Schedule – XXVII Operations in Foundries 1. Application - Provisions of this schedule shall apply to all parts of factories where any of the following operations or processes are carried on: (a) the production of iron castings or, as the case may be, steel castings by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by shall moulding, or by centrifugal casting and any process incidental to such production; (b) the production of non-ferrous castings by casting metal in moulds made of sand, loam , metal, moulding composition or other material or mixture of materials, or by shall mouldings, die-casting (including pressure die casting), centrifugal casting or continuous casting and any process incidental to such production; and (c) the melting and casting of non-ferrous metal for the production of ingots, billets, slabs or other similar products, and the stripping thereof; But shall not apply with respect to - (a) Any process with respect to the smelting and manufacture of lead and the Electric Accumulators; (b) Any process for the purpose of a printing works; or (c) Any smelting process in which metal is obtained by a reducing operation or any process incidental to such operation; or (d) The production of steel in the form of ingots; or (e) Any process in the course of the manufacture of solder or any process incidental to such manufacture; or (f) the smelting and casting of lead or any lead-based alloy for the production of ingots, billets, slabs or other similar products or the stripping thereof, or any process incidental to such melting, casting or stripping. 2. Definition - For the purpose of this schedule - (A) ”approved respirator’ means a respirator of a type approved by the Chief Inspector; (B) ”cupola of furnace” includes a receiver associated therewith; (C) ”dressing or fettling operations” includes stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not include (a) the removal of metal from a casting when performed incidentally in connection with the machining or assembling of castings after they have been dressed or fettled, or (b) any operation which is knock-out operation within the meaning of this schedule; (D) ”foundry” means those parts of a factory in which the production of iron or steel or non-ferrous castings (not being the production of pig iron or the production of steel in the form of ingots) is carried on by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by shell moulding or by centrifugal casting in metal moulds lined with sand, or die casting including pressure die casting, together with any part of the factory in which any of the following processes are carried on as incidental processes in connection with and in course of, such production, namely, the preparation and preparation of moulds and cores, knock out operations and dressing or fettling operations; (E) “knock-out operations” means all methods of removing castings from moulds and the following operations, when done in connection therewith, namely, stripping, coring-out and the removal of runners and risers; (F) ”pouring aisle” means an aisle leading from a main gangway or directly from a cupola or furnace to where metal is poured into moulds. 3. Prohibition of use of certain materials as parting materials - (1) A material shall not be used as a parting material if it is a material containing compounds of silicon calculated as silica to the extent more than 5 percent by weight of the dry material : Provided that this prohibition shall not prevent the following being used as a parting material if the material does not contain an admixture of any other silica - (a) Zirconium silicate (Zircon) (b) Calcined china clay (c) Calcined aluminous fireclay (d) Sillimanite (e) Calcined or fused alumina (f) Olivine (g) Natural sand (2) Dust or other matter deposited from a fettling or blasting process shall not be used as a parting material or as a constituent in a parting material. 4. Arrangement and storage - For the purposes of promoting safety and cleanliness in workrooms the following requirements shall be observed:- (a) moulding boxes, loam plates, ladles, patterns, pattern plates, frames, boards, box weights, and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; (b) Suitable and conveniently accessible racks, bins, or other receptacles shall be provided and used for the storage of other gear and tools; (c) Where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. 5. Construction of floors - (1) Floors of indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have been surface of hard material. (2) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. (3) All parts of the surface of the floor of any such indoor workplace which are of sand shall, so far as practicable, be maintained in an even and firm condition. 6. Cleanliness of indoor workplaces.- (1) All accessible parts of the walls of every indoor workplace in which the processes are carried on and of everything affixed to those wall shall be effectively cleaned by a suitable method to a height of not less than 4.2 metres from the floor at least once in every period of fourteen months. A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date (which shall be not less than five months nor more than nine months after the last immediately preceding washing, cleaning or other treatment.) (2) Effective cleaning by a suitable method shall be carried out at least once every working day of all accessible parts of the floor of every indoor workplace in which the processes are carried on, other than parts which are of sand; and the parts which are of sand shall keep in good order. 7. Manual operations involving molten metal - (1) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation - (a) Which is adequate for the safe performance of the work and (b) Which, so far as reasonably practicable, is kept free from obstruction? (2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which where any person walks while engaged in the operation shall be on the same level: Provided that, where necessary to enable the operation to be performed without undue risk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 8. Gangways and pouring aisles - (1) In every workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule and, so far as reasonably practicable, in every other workroom to which this Paragraph applies, sufficient and clearly defined main gangway shall be provided and properly maintained which - (a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; (b) shall be kept, so far as reasonably practicable, free from obstruction; (c) if not used for carrying molten metal, shall be at least 920 millimetres in width; (d) if used for carrying molten metal shall be - (i) Where truck ladles are used exclusively, at least 600 millimetres wider than the overall width of the ladle; (ii) Where hand shanks are carried by not more than two men, at least 920 millimetres in width; (iii) Where hand shanks are carried by more than two men, at least 1.2 matters in width; and (iv) Where used for simultaneous travel in both directions by men carrying hand shanks, at least 1.8 metres in width. (2) In workroom to which this Paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule, sufficient and clearly defined pouring aisles shall be provided and properly maintained which - (a) shall have an even surface of hard material and shall, in particular, not be sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; (b) Shall be kept so far as reasonably practicable free from obstruction; (c) if molten metal is carried in hand ladles or bulk ladles by not more than two men per ladle, shall be at least 460 millimetres wide, but where any moulds alongside the aisle are more than 510 millimetres above the floor of the aisle, the aisle shall be not less than 600 millimetres wide; (d) if molten metal is carried in hand ladles or bull ladles by more than two men per ladle, shall be at least 760 millimetres wide; (e) if molten metal is carried in crane, trolley or truck ladles, shall be of a width adequate for the safe performance of the work. (3) Requirements of sub-paragraph (1) and (2) shall not apply to any workroom or part of a workroom if, by reason of the nature of the work done therein, the floor of that workroom or, as the case may be, that part of a workroom has to be of sand. (4) In this paragraph “workroom to which this paragraph applies” means a part of a ferrous or non-ferrous foundry in which molten metal is transported or used, and a workroom to which this paragraph applies shall be deemed for the purposes of this paragraph to have been constructed, reconstructed or converted for use as such after the making of this schedule if the construction, reconstruction or conversion thereof was begun after the making of this schedule. 9. Work near cupolas and furnaces - No person shall carry out any work within a distance of 4 metres from a vertical line passing through the delivery end of any spout of a cupola or furnace, being a spout used for delivering molten metal, or within a distance of 2.4 metres from a vertical line passing through the nearest part of any ladle which is in position at the end of such a spout, except, in either case, where it is necessary for the proper use of maintenance of a cupola or furnace that work should be carried out within that distance of that work is being carried out at such a time and under such conditions that there is no danger to the person carrying it out from molten metal which is being obtained from the cupola or furnace or is in a ladle in position at the end of the spout. 10. Dust and fumes.- (1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. (2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. (3) Mould stoves, core stoves and annealing furnaces shall be so designed constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. (4) All knock-out operations shall be carried out - (a) in a separate part of foundry suitably partitioned off, being a room or part in which, so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard of general ventilation are provided; or (b) in an area of the foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. (5) All dressing or fettling operations shall be carried out - (a) In a separate room or in a separate part of foundry suitably partitioned off; or (b) In an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 11. Maintenance and examination of exhaust plant - (1) All ventilation plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be properly maintained. (2) All ventilating plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person at least once in every such examination and test shall be entered in an approved register which shall be available for inspection by an Inspector. Any defect found on any such examination and carrying out the examination and test to the occupier or manager of the factory. 12. Protective equipment - (1) The occupier shall provide and maintain protective equipment specified for the protection of workers, (a) suitable gloves to other protection for the hands for workers engaged in handling any hot material likely to cause damage to the hands by burn, scald, or scar, or in handling pig iron, rough castings or other articles likely to cause damage to the hands by cut or abrasion; (b) approved respirators for workers carrying out any operations creating a have dust concentration which cannot be dispelled quickly and effectively by the existing ventilation arrangements. (2) No respirator provided for the purposes of clause 1(b) has been worn by a person shall be worn by another person if it has not since been thoroughly cleaned and disinfected. (3) Persons who for any of their time - (a) work at a spout of or attend to, a cupola or furnace in such circumstances that material there from may come into contact with the body, being material at such a temperature that its contact with the body would cause a burn; or (b) Are engaged in, or in assisting with, the pouring of molten metal; or (c) carry by hand or move by manual power any ladle or mould containing molten metal; or (d) are engaged in knocking-out operations involving material at such a temperature that its contact with the body would cause a burn; Shall be provided with suitable footwear and gaiters which worn by them prevent, so far as reasonably practicable, risk of burns to his feet and ankles. (4) Where appropriate, suitable screens shall be provided for protection against flying materials (including splashes of molten metal and sparks and chips thrown off in the course of any process). (5) The occupier shall provide and maintain suitable accommodation for the storage and make adequate arrangements for cleaning and maintaining of the protective equipment supplied in pursuance of this paragraph. (6) Every person shall make full and proper use of the equipment provided for his protection in pursuance of sub-paragraph (1) and (4) and shall without delay report to the occupier, manager, or other appropriate person any defect in, or less of, the same. 13. Washing and bathing facilities - (1) There shall be provided and maintained in clean state and good repair for the use of all workers employed in the foundry - (a) A wash place under cover with either - (i) a trough with impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every 10 such persons employed at any one time and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 centimetres or (ii) at least one tap or stand pipe for every 10 such persons employed at any one time, and having a constant supply of clean water, the tap or stand pipe being spaced not less than 1.2 metres apart; and (b) Not less than one half of the total number of washing places provided under clause (a) shall be in form of bath rooms. (c) A sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. (2) The facilities provided for the purposes of sub-paragraph (1) shall be placed in charge of a responsible person or persons and maintained in a clean and orderly condition. 14. Disposal of dross and skimming - Dross and skimming removed from molten metal or taken from a furnace shall be placed forthwith in suitable receptacles. 15. Disposal of waste - Appropriate measures shall be taken for the disposal of all waste products from shell moulding (including waste burnt sand) as soon as reasonably practicable after the castings have been knocked-out. 16. Material and equipment left out of doors - All material and equipment left out of doors (including material, and equipment so left only temporarily or occasionally) shall be so arranged and placed as to avoid unnecessary risk. There shall be safe means of access to all such material and equipment and, so far as reasonably practicable, such access shall be by roadways or pathways which shall be properly maintained. Such roadways or pathways shall have a firm and even surface and shall, so far as reasonably practicable be kept free from obstruction. 17. Medical facilities and records of examinations and tests - (1) The occupier of every factory to which this schedule applies, shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of such examinations carried out by the medical practitioner shall be maintained in a separate, register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 18. Medical examination by certifying Surgeon - (1) every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examinations shall include skin test for dermatitis and no worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in a manganese process shall be re-examined by a Certifying Surgeon at least once in every 12 months and such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests in sub- paragraph (1). (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manger of the factory. The record of each examination carried out under sub-paragraph (1) and (2) including the nature and the results of these test, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon , in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 19. Exemptions - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for the protection of the workers in the factory, the Chief Inspector may be a certificate in writing which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Rule 103: [Framed U/S 88of the Act] Notification of Accidents and Dangerous Occurrences (1) When any accident which results in the death of any or which results in such bodily injury to any person as is likely to cause his death, or any dangerous occurrence specified in the Schedule to this rule takes place in a factory, the manager of the factory shall forthwith send a notice thereof by telephone, special messenger or telegram to the Inspector and the Chief Inspector. (2) When any accident or any dangerous occurrence specified in the Schedule to this rule which results in the death of any person or which results in such bodily injury to any person as is likely to cause his death, takes place in a factory, a notice as mentioned in sub-rule (1) shall also be sent to- (a) the District Magistrate or Sub-Divisional Magistrate; (b) the Officer-in-charge of the Police Station; and (c) the relatives of the injured or deceased person. (3) Any notice given as required under sub-rules (1) and (2) shall be confirmed by the manager of the factory to the authorities mentioned in sub-rules (1) and (2) within twelve hours of the accident or the dangerous occurrence by sending them a written report in Form 18 in the case of an accident or dangerous occurrence causing death or bodily injury to any person in Form 18-A in the case of dangerous occurrence which has not resulted in any bodily injury to any person. (4) When any accident or dangerous occurrence specified in the Schedule below takes place in a factory and it causes such bodily injury to any person as prevents the person injured from working for a period of forty-eight hours or more immediately following the accident or the dangerous occurrence, as the case may be, the manager of the factory shall send a report thereof to the Inspector and Chief Inspector in Form 18 within twenty-four hours after the expiry of the forty-eight hours from the time of the accident or the dangerous occurrence: Provided that if an in the case of an accident or dangerous occurrence, death occurs of any person injured by such accident or dangerous occurrence after the notices and reports referred to in the foregoing sub-rule have been sent, the manager of the factory shall forthwith send a notice thereof by telephone, special messenger or telegram to the authorities and persons mentioned in sub-rules (1) and (2) and also have this information confirmed in writing within twelve hours of the death; Provided further that, if the period of disability from working for forty-eight hours or more referred to in sub-rule (4) does not occur immediately following the accident, or the dangerous occurrence, but later on occurs in more than one spell, the report referred to in clause (3) shall be sent to the Inspector and Chief Inspector in Form 18 within twenty-four hours immediately following the hour when the actual total period of disability from working resulting from the accident or the occurrence dangerous becomes forty-eight hours. SCHEDULE The following class of dangerous occurrence whether or not attended by personal injury or displacement, shall be dangerous occurrence within the meaning of rule 103:- (a) Bursting of plant used for containing or supplying of steam under pressure greater than atmospheric pressure. (b) Collapse or failure of crane, derrick, winch, hoist or any other appliance used in raising or lowering persons or goods or any other part thereof, or the over turning of crane. (c) Explosion, fire, bursting out, leakage or escape of any molten metal or hot liquid or gas causing bodily injury to any person or damage to any room or place in which persons are employed or fire in the room of cotton pressing factories where cotton opener is in use. (d) Explosion of receiver or container used for storage of pressure greater than atmospheric pressure of any gas(including air) or any liquid or solid resulting from the compression of gas. (e) Collapse or subsidence of any floor, gallery, roof, bridge, tunnel, chimney, wall, building or any other structure. Rule 104: [Framed U/S 89 of the Act] Notice of poisoning or disease under section 89 A notice in Form 19 should be sent forthwith both to the Chief Inspector and to the Certifying Surgeon by the Manager of a factory in which there occurs a case of lead, phosphorus, mercury, manganese, arsenic, carbon bisulphide or benzene poisoning or poisoning by nitrous fumes, or by halogen or halogen derivatives of the hydrocarbons of the aliphatic series; or of chrome ulceration, anthrax, silicosis, toxic anaemia, toxic jaundice, primary opitheliomatous cancer of the skin, or pathological manifestations due to radium or other radio-active substances or X- Rays. Rule 104A: [Framed U/S 41-F & 112 of the Act] Permissible levels of certain chemical substances in work environment Without prejudice to the requirements in any other provisions in the Act or the rules made there under, the requirements specified in the Schedule given below shall apply to all factories:--- SCHEDULE 1. Definitions: for the purpose of this schedule - (a) “mg/m3” means milligrams of a substances per cubic metre of air; (b) “mppem” means million particles of a substance per cubic metre of air; (c) “ppm” means parts of vapour or gas per million parts of air by volume at 25 degrees centigrade and 760 mm of mercury pressure; (d) ”Time weighted average concentration” means the average concentration of a substance in the air at any work location in a factory computed from evaluation of adequate number of air samples taken at that location, spread over the entire shift on any day, after giving weightage to the duration for which each such sample is collected and the concentration prevailing at the time of taking the sample. Time weighted average C1T1 + C2T2 + ........CnTn Concentration = ------------------------------------ T1 + T2 +.........Tn Where C1 represents the concentration of the substance for duration T1 (in hours); C2 represents the concentration of the substance for duration T2 (in hours); and Cn represents the concentration of the substance for duration Tn (in hours). (e) “Work location” means a location in a factory at which a worker works or may be required to work at any time during any shift on any day. 2. Limits of concentration of substances at work location: - (I) The time weighted average concentration of any substance listed in table 1 or 2 of the schedule, at any work location in a factory during any shift on any day shall not exceed the limit of the permissible time weighted average concentration specified in respect of that substance: Provided that in the case of a substance mentioned in Table 1 in respect of which a limit in terms of short term maximum concentration is indicated, the concentration of such a substance may exceed the permissible limit of the time weighted average concentration for the substance for short periods not exceeding 15 minutes at a time, subject to the condition that- (a) Such periods during which the concentration exceeds the prescribed time weighted average concentration are restricted to not more than 4 per shift; (b) the time interval between any two such periods of higher exposure shall not be less than 60 minutes; and (c) At no time the concentration of the substance in the air shall exceed the limit of short term maximum concentration. (II) In the case of any substance given in Table 3, the concentration of the substance at any work location in a factory at any time during any day shall not exceed the limit of exposure for that substance specified in the table. (III) In the cases where the word “skin” has been indicated against certain substance mentioned in Tables 1 and 3, appropriate measures shall be taken to prevent absorption through cutaneous routes particularly skin, mucous membranes, and eyes as the limits specified in these Tables are for conditions where the exposure is only through respiratory tract. (IV) (a) In case, the air at any work location contains a mixture of such substances mentioned in Table 1, 2 or 3, which have similar toxic properties, the time weighted concentration of each of these substances during the shift should be such that when these time weighted concentration divided by the respective permissible time weighted average concentration specified in the above mentioned tables, and the fractions obtained are added together, the total shall not exceed unity. C1 C2 Cn ----- + ------- + ----------------- + ------- L1 L2 Ln Where C1, C2.......... Cn are the time weighted concentration of toxic substances 1, 2---------- ,and n respectively, determined after measurement at work location; And L1, L2 .........Ln are the permissible time weighted average concentration of the toxic substances 1, 2, and n respectively. (b) In case the air at any work location contains a mixture of substances, mentioned in Table 1, 2, 3 and these do not have similar toxic properties, then the time weighted concentration of each of these substances shall not exceed the permissible time weighted average concentration specified in the above mentioned tables, for that particular substance. (c) The requirement in clauses (a) and (b) shall be in addition to the requirements in paragraphs 2 (1) and 2(2). 3. Sampling and evaluation procedures.- (1) Notwithstanding provisions in any other paragraphs, the sampling and evaluation procedures to be adopted for checking compliance with the provisions in the schedule shall be as per standard procedures in vogue from time to time. (2) Notwithstanding the provisions in paragraph 5, the following conditions regarding the sampling and evaluation procedures relevant to checking compliance with the provisions in the schedule are specified. (a) For determination of the number of particles per cubic meter in item 1 (a)(i)(1) in Table 2, samples are to be collected by standard or midget impinger and the counts made by light-field technique. (b) The percentage of quartz in the 3 formulae given in item 1(a)(i) of Table 2 is to be determined from air borne samples. (c) For determination of number of fibres as specified in item 2(a) of Table 2, the membrane filter method at 430 x magnification (4mm objective) with phase contrast illumination should be used. (d) Both for determination of concentration and percentage of quartz for use of the formula given in item 1(a)(i)(2) of Table 2, the fraction passing through a size-selector with the following characteristics should only be considered. Aerodynamic diameter Percentage allowed (unit density sphere) by size-selector 2.0 90 2.5 75 3.5 50 5.0 25 10.0 0 4. Power to require assessment of concentration of substances.-(1)An Inspector may, by an order in writing, direct the occupier or manager of a factory to get before any specified date, the assessment of the time weighted average concentration at any work location of any of the substances mentioned in Table 1,2 or 3 carried out. (2) The results of such assessment as well as the method followed for air sampling and analysis for such assessment shall be sent to the Inspector within 3 days from the date of completion of such assessment and also a record of the same kept readily available for inspection by an Inspector. 5. Exemption.- If in respect of any factory or a part of a factory, the Chief Inspector is satisfied that, by virtue of the pattern of working time of the workers at different work locations or an account of other circumstances, no worker is exposed, in the air at the work locations, to a substance or substances specified in Tables 1,2 or 3 to such an extent as is likely to be injurious to his health, he (the Chief Inspector) may by an order in writing, exempt the factory or a part of the factory from the requirements in paragraph 2, subject to such conditions, if any, as he may specify therein. TABLE - 1 Substance permissible level of exposure ----------------------------------------------------------------------------- Time-weighted average short-term maximum concentration concentration ppm mg/m3 ppm mg/m3 Acetic acid 10 25 15 37 Acrelein 0.1 0.25 0.3 0.8 Aldrin-skin - 0.25 - 0.75 Ammonia 25 18 35 27 Aniline-skin 2 10 5 20 Anisidine (o-poisoners) 0.1 0.5 - - -skin Arsenic & compounds (as) - 0.2 - - Benzene 10 30 - - Bromine 0.1 0.7 0.3 2 2 Butanene Methylethyl Ketone – MEK 200 590 300 885 N-Butyl acetate 150 710 200 950 Sec/tert.Butyl acetate 200 950 250 1190 Cadmium-dust and Salts (as Cd) - 0.05 - 0.2 Calcium Oxide - 2 - - Carbaryl (Sovin) - 5 - 10 Carbofuran (Furadan) - 0.1 - - Carbon disulphide-skin 2 60 30 90 Carbon monoxide 50 55 400 440 Carbon tetrachloride-skin 10 65 20 130 Carbonyl chloride (Phosgene) 0.1 0.4 - - Chlordane-skin - 0.5 - 2 Chlorobenzene (mono chloro- benzene) 75 350 - - Chlorine 1 3 3 9 bis-Chloromethyl ether 0.001 - - - Chromic acid and Chromates (as Cr.) - 0.05 - - Chromium, Sel-Chromic, Chromous salts (as Cr) - 0.5 - - Copper fume - 0.2 - - Cotton dust, raw - 0.2 - 0.6 Cresol, all isomers-skin 5 22 - - Cyanides, (as CN)-skin - 5 - - Cyanogen 10 20 - - DDT (Dichlorodiphenyl-trichlore-ethane) - - - 3 Demeton-skin 0.01 0.1 0.03 0.3 Diazion-skin - 0.1 - 0.3 Dibutyl phthalate - 5 - 10 Dichlorves (DDVP) -skin 0.1 1 0.3 3 Dieldrin-skin - 0.25 - 0.75 Dinitrobenzene (all isomers) skin 0.15 1 0.5 3 Dinitrotoluene-skin - 1.5 - 5 Diphenyl 0.2 1.5 0.6 4 Endosulfan (Thiodan)-skin - 0.1 - 0.3 Endrin-skin - 0.1 - 0.3 Ethyl acetate 400 1000 - - Ethyl alcohol 1000 1900 - - Ethyl amine 10 18 - - Flourides (as F) - 2.5 - - Flourine 1 2 2 4 Hydrogen Cyanide-skin 10 11 15 16 Hydrogen sulfide 10 15 15 27 Iron oxide fume (Fe2O3 as Fe) - 5 - 10 Isoamyl alcohol 100 360 125 450 Isobutylalcohol 50 150 75 225 Lead, inorg, fumes and dusts (as Pb) - 0.15 - 0.45 Lindane-skin - 0.5 - 1.5 Mala thion-skin - 10 - - Manganese fume (as Mn) - 1 - 3 Mercury (as Hg) - 0.05 - 0.15 Mercury (alkyl compounds) -skin (as Hg) 0.001 0.01 0.003 0.03 Methyl alcohol (methanol) skin 200 260 250 310 Methyl cellosolve-skin (2-methoxy ethanol) 25 80 35 120 Methyl isobutyl ketone-skin 100 410 125 510 Naphthalene 10 50 15 75 Nickel carbonyl (as Ni) 0.05 0.35 - - Nitric acid 2 5 4 10 Nitric oxide 25 30 35 45 Nitrobenzene-skin 1 5 2 10 Oil mist-mineral - 5 - 10 Parathion-skin - 0.1 - 0.3 Phenel-skin 5 19 10 38 Phorate (Thimet)-skin - 0.05 - 0.2 Phosgene (Carbonyl chloride) 0.1 0.4 - - Phosphine 0.3 0.4 1 1 Phosphorous (yellow) - 0.1 - 0.3 Phosphorous pentachloride - 1 - 3 Phosphorous trichloride 0.5 3 - - Picric acid-skin - 0.1 - 0.3 Pyridine 5 15 10 30 Silane (silicon tetrahydride) 0.5 0.7 1 1.5 Styrene, monomer (phenyl-ethylene) 100 420 125 525 Sulphur dioxide 5 13 - - Sulphuric acid - 1 - - Toluene (toluol)-skin 100 375 150 560 0-Toludine 5 22 10 44 Trichloroethylene 100 535 150 800 Vinyl chloride 5 10 - - Welding fumes (NOC) - 5 - - Xylene (o-m-isomers)-skin 100 435 150 655 TABLE – 2 Substance Permissible time weighted average concentration 1. Silica (a) Crystalline (i) Quartz 1060 ---------------------------------Mppcm (1) In terms of dust count: - % Quartz + 10 (2) In terms of respirable dust 10 -------------------------------- Mg/m3 % respirable quartz + 2 (3) In terms of total dust: 30 ----------------------------- mg/m3 % quartz + 3 (ii) Cristobalite Half the limits given against quartz (iii) Tridymite Half the limits given against quartz (iv) Silica fused Same limit as for quartz (v) Tripoli Same limit as in formula in item 2 Given against quartz (b) Amorphous 705 mppcm 2. Silicate having less than 1% Free silica by weight (a) Asbestos (fibres longer than 5 microns) 2 fibres/cubic centimetre (b) Mica 705 mppcm (c) Mineral Wool fibre 10 mg/m3 (d) Porlite 1060 mppcm (e) Portland cement 1060 mppcm (f) Soap stone 705 mppcm (g) Talc (nonobostiform) 705 mppcm (h) Talc (fibrous) same limit as for asbestos (i) Tromolite same limit as for asbestos 3. Coal dust (1) For airborne dust having less Than 5 % silicon dioxide By weight 2mg/m3 (2) For airborne dust having same limit as prescribed by Over 5% silicon dioxide formulas in item (2) against quartz. TABLE - 3 -------------------------------------------------------------------------------------------- Substance Permissible limit of exposure ppm mg/m3 -------------------------------------------------------------------------------------------- Acetic anhydride 5 20 O-Dichlorobenzene 50 300 Formaldehyde 2 3 Hydrogen Chloride 5 7 Manganese & compounds (as Mn) - 5 Nitrogen dioxide 5 9 Nitroglycerin-skin 0.2 2 Potassium hydroxide - 2 Sodium hydroxide - 2 2, 4, 6 - Trinitrotoluene (TNT) - 0.5 -------------------------------------------------------------------------------------------- CHAPTER-X SUPPLEMENTAL Rule 105: [Framed U/S 107(3) of the Act] Procedure in appeals (1) An appeal presented under section 107 shall lie to the Chief Inspector, or in cases where the order appealed against is an order passed by that officer, to the state commissioner, and shall be in the form of a memorandum setting forth concisely grounds of objection to the order and bearing court-fees stamp in accordance with Article II of Schedule II to the Court-fees Act, 1870, and shall be accompanied by a copy of the order appealed against. (2) Appointment of assessors - On receipt of the memorandum of appeal, the appellate authority may, if it thinks fit or if the appellant has requested that the appeal should be heard with the aid of assessors, call upon the body specified in sub-rule (4) being the representative of the industry concerned to appoint an assessor within a period of 14 days. If an assessor is nominated by such body, the appellate authority shall appoint a second assessor itself. It shall then fix a date for the hearing of the appeal and shall give due notice of such date to the appellant and to the Inspector whose order is appealed against, and shall call upon the two assessors to appear upon such date to assist him in the hearing of the appeal. (3) The appellant shall state in the memorandum presented under sub-rule (1) whether he is a member of one or more of the following bodies:- (A) The Punjab Chamber of Commerce, New Delhi. (B) The Federation of Industries, Amritsar. (C) The Textile Manufacturers' Association, Amritsar. (D) The Factory Owners Association, Batala. (E) Desi Beopar Mandal, Ambala. (4) The body empowered to appoint the assessor shall- (a) if the appellant is a member of one of such bodies, by that body; (b) if he is a member of two such bodies, by the body which the appellant desires should appoint such assessor; and (c) if the appellant is not a member of any of the aforesaid bodies or if he does not state in the memorandum which of such bodies he desires should appoint the assessors, the body which the appellate authority considers as the best fitted to represent the industry concerned. (5) Remuneration of assessors.-An assessor appointed in accordance with the provisions of sub-rules (2) and (3) shall receive for the hearing of the appeal, a fee to be fixed by the appellate authority subject to a maximum of fifty rupees per diem. He shall also receive the actual traveling expenses. The fees and traveling expenses shall be paid to the assessor by Government; but where assessors have been appointed at the request of the appellant and the appeal has been decided wholly or partly against him the appellate authority may direct that the fees and traveling expenses of the assessor shall be paid in whole or in part by the appellant. Rule 106: [Framed U/S 108 of the Act] Display of notices The abstract of the Act and of the Rules required to be displayed in every factory shall be in

Previous and next

All provisions of Punjab Factories Rules 1952

Questions people ask

Is appendix of Punjab Factories Rules 1952 still in force?

No repeal of Punjab Factories Rules 1952 is recorded.