Appendix B, Punjab Factories Rules 1952: APPENDIX-B
Punjab Factories Rules 1952 - Appendix B
Text of appendix B
APPENDIX-B
APPENDIX-B
[SEE CLAUSE 11]
CAUTIONARY NOTICE
Benzene and substances containing benzene
1. Hazards:
(a) Benzene and substances containing benzene are harmful.
(b) Prolonged or repeated breathing of benzene vapours may result in acute or
chronic poisoning.
(c) Benzene can also be absorbed through skin which may cause skin or other
diseases.
2. Preventive measures:
(a) Avoid breathing of benzene vapours.
(b) Avoid prolonged or repeated contact of benzene with the skin.
(c) Remove benzene soaked or wet clothing promptly.
(d) If any time you are exposed to high concentration of benzene vapours and exhibit
signs and symptoms such as dizziness, difficulty in breathing, excessive excitation and
losing of consciousness, immediately inform your factory manager.
(e) Keep all the containers of benzene closed
(f) Handle, use and process benzene and substances containing benzene carefully in
order to prevent their spillage on floor.
(g) Maintain good housekeeping.
3. Protective equipment:
(a) Use respiratory protective equipment in places where benzene vapours are present
in high concentration.
(b) In emergency, use self generating oxygen mask or oxygen or air cylinder masks.
(c) Wear hand gloves, aprons, goggles and gum boots to avoid contact of benzene
with your skin and body parts.
4. First-aid measures in case of acute benzene poisoning :
(a) Remove the clothing immediately if it is wetted with benzene.
(b) If liquid benzene enters eyes, flush thoroughly for at least 15 minutes with clean
running water and immediately secure medical attention.
(c) In case of unusual exposure to benzene vapour, call a physician immediately. Until
he arrives, do the following :-
(i) If the exposed person is conscious -
(a) Move him to fresh air in open.
(b) Lay down without a pillow and keep him quiet and warm.
(ii) If the exposed person is unconscious -
(aa) Lay him down preferably on the left side with the head low.
(bb) Remove any false teeth, chewing gum, tobacco or other foreign objects
which may be in his mouth.
(cc) Provide him artificial respiration in case difficulty is being experienced in
breathing.
(dd) In case of shallow breathing or cyanosis (blueness of skin, lips, ears,
finger nail beds), he should be provided with medical oxygen or oxygen carbon
dioxide mixture. If needed, he should be given artificial respiration. Oxygen
should be administered by a trained person only.
Schedule – XXII
Manufacturing process or operation in carbon disulphide plants
1. Application - This schedule shall apply to all electric furnaces in which carbon disulphide is
generated and all other plants where carbon disulphide after generation, is condensed, refined
and stored. This schedule is in addition to and not in derogation of any of the provisions of the
Act and Rules made there under.
2. Construction, installation and operation-
(1) The buildings in which electric furnaces are installed and carbon disulphide after
generation is condensed and refined shall be segregated from other parts of the factory
and shall be of open type to ensure optimum ventilation and the plant layout shall be
such that only a minimum number of workers are exposed to the risk of any fire or
explosion at any one time.
(2) Every electric furnace and every plant in which carbon disulphide is condensed,
refined and stored with all their fittings and attachments shall be of good construction,
sound material and of adequate strength to sustain the internal pressure to which the
furnace or the plant may be subjected to and shall be so designed that carbon
disulphide liquid and gas are in closed system during their normal working.
(3) The electric furnace supports shall be firmly grouted about 60 centimetres in
concrete or by other effective means.
(4) Every electric furnace shall be installed and operated according to
manufacturers’ instructions and these instructions shall be clearly imparted to the
personnel in charge of construction and operation.
(5) The instructions regarding observance of correct furnace temperature,
sulphur dose, admissible current or power consumption and periodical checking of
charcoal level shall be strictly complied with.
3. Electrodes -
(1) Where upper ring electrodes made of steel are used in the electric furnace,
they shall be of seamless tube construction and shall have arrangement for being
connected t cooling water system through a siphon built in the electrodes or through a
positive pressure water-pump.
(2) The arrangement for cooling water referred to in sub-paragraph (1) shall be
connected with automatic alarm system which will actuate in the event of interruption of
cooling water in the electrodes and give visible and audible alarm signals in the control
room and simultaneously stop power supply for the furnace operation and to stop the
further supply of water. The alarm system and the actuating device shall be checked
every day.
4. Charcoal level indicator and vibrator – Means shall be provided on each electric
furnace for indicating the correct level of charcoal in the furnace and vibrating the charcoal.
This mean shall employed often as necessary to maintain correct charge and level of
charcoal.
5. Charcoal separator - A cyclone type of charcoal separator shall be fitted on the off take
pipe between the electric furnace and sulphur separator to prevent entry of pieces of charcoal
into the condensers and piping.
6. Rupture discs and safety seal -
(1) At least two rupture discs of adequate size which shall blow off at a
pressure twice the maximum operating pressure shall be provided on each furnace and
shall either be mounted directly on the top of the furnace or each through an
independent pipe as close as possible to the furnace.
(2) A safety water seal shall be provided and tapped from a point between the
charcoal separator and the sulphur separator.
7. Pyrometer and manometers -
(1) Each electric furnace shall be fitted with adequate number of pyrometers to
give an indication of the temperature as correctly as reasonably practicable at various
points in the furnace. The dials for reading the temperatures shall be located in the
control room.
(2) Manometers or any other suitable devices shall be provided for indicating
pressure –
(a) In the off take pipe before and after the sulphur separator; and
(b) In primary and secondary condensers.
8. Check valves - All piping carrying carbon disulphide shall be fitted with check valves at
suitable positions so as to prevent gas from flowing back into any electric furnace in the
event of its shut down.
9. Inspection and maintenance of electric furnaces -
(1) Every electric furnace shall be inspected internally by a competent person.
(a) Before being placed in service after installation;
(b) Before being placed in service after reconstruction or repairs; and
(c) Periodically every time the furnace is opened for cleaning or de- or
for replacing electrodes.
(2) When an electric furnace is shut down for cleaning or de--
(a) The brick lining shall be checked for continuity and any part found
defective removed;
(b) After removal of any part of the lining referred to in (a) the condition
of the shell shall be closely inspected; and
(c) Any plates forming shall found corroded to the extent that safety of
the furnace is endangered shall be replaced.
10. Maintenance of records - The following hourly records shall be maintained in a log
book.
(a) Manometer readings at the points specified in sub-paragraph 7(2);
(b) Gas temperature indicated by pyrometers and all other vital points near the
sulphur separator and primary and secondary condensers;
(c) Water temperature and flow of water through the siphon in the electrodes;
and
(d) Primary and secondary voltages and current and energy consumed.
11. Electrical apparatus, wiring and fittings - All buildings in which carbon disulphide
id refined or stored shall be provided with electrical apparatus, wiring and fittings which shall
afford adequate protection from fire and explosion.
12. Prohibition relating to smoking - No person shall smoke or carry matches, fire or
naked light or other means of producing a naked light or spark in buildings in which carbon
disulphide is refined or stored, and a notice in the language understood by a majority of the
workers shall be posted in the plant prohibiting smoking and carrying of matches, fire or naked
light or other means of producing naked light or spark into such rooms.
13. Means of escape - Adequate means of escape shall be provided and maintained
to enable persons to move to a safe place as quickly as possible in case of an emergency. At
least two independent staircases of adequate width shall be provided in every building housing
the furnaces at reasonable intervals at opposite ends. These shall always be kept clear of all
obstructions and so designed to afford easy passage.
14. Warnings in case of fire - There shall be adequate arrangements for giving
warnings in case of fire or explosion which shall operate on electrically and in case of failure of
electricity by some mechanical means.
15. Fire-fighting equipment -
(1) Adequate number of suitable fire extinguishers or other fire-fighting
equipment shall be kept in constant readiness for dealing with risks involved and
depending on the amount and nature of materials stored.
(1) (2) Clear instructions as to how the extinguishers or other equipment
should be used printed in the language which the majority of the workers
employed understand, shall be affixed to each extinguisher or other equipment
and the personnel trained in their use.
16. Bulk Sulphur -
(1) Open or semi-enclosed spaces for storage of bulk sulphur shall be sited with
due regard to the dangers which may arise from sparks given off by nearby
locomotives, etc., and precautions shall be taken to see that flames, smoking and
matches and other sources of ignition do not come in contact with the clouds of dust
arising during handling of bulk sulphur.
(2) All enclosures for bulk sulphur shall be of non-combustible construction,
adequately ventilated and so designed as to provide a minimum of ledges on which
dust may lodge.
(3) The bulk sulphur in the enclosures shall be handled in such a manner as to
minimise the formation of dust clouds and no flame, smoking and matches or other
sources of ignition shall be employed during handling and non-sparking tools shall be
used whenever sulphur is shovelled or otherwise removed by hand.
(4) No repairs involving flames, heat or use of hand or power tools shall be
made in the enclosure where bulk sulphur is stored.
17. Liquid sulphur - Open flames, electric sparks and other sources of ignition, including
smoking and matches, shall be excluded from the vicinity of molten sulphur.
18. Training and supervision -
(1) All electric furnaces and all plants in which carbon disulphide is condensed,
refined or stored shall be under adequate supervision at all times while the furnaces
and plant are in operation.
(2) Workers in charge of operation and maintenance of electric furnaces and
the plants shall be properly qualified and adequately trained.
19. Washing facilities -
(1) The occupier shall provide and maintain in a clean state and in good repair,
for the use of all persons employed wash place under cover with at least one tap or
stand-pipe, having a constant supply of clean water for every five such persons, the
taps or stand-pipes being spaced not less than 120 centimetres apart with a sufficient
supply of soap and clean towels, provided that towels shall be supplied individually to
each worker if so ordered by the Inspector.
(2) All the workers employed in the sulphur storage, handling and melting
operations shall be provided with a nail brush.
20. Personal protective equipment -
(1) Suitable goggles and protective clothing consisting of overalls without
packets, gloves and foot-wear shall be provided for the use of operatives –
(a) when operating valves or cocks controlling fluids etc.,
(b) drawing off a molten sulphur from sulphur pots;
(c) handling charcoal or sulphur.
(2) Suitable respiratory protective equipment shall be provided and stored in
the appropriate place for use during abnormal conditions or in an emergency.
(3) Arrangements shall be made for proper and efficient cleaning of all such
protective equipment.
21. Cloakrooms - There shall be provided and maintained for the use of all persons
employed in the processes a suitable cloakroom for clothing put off during work hours and a
suitable place separate from the cloakroom for the storage or overalls or working clothes. The
accommodation so provided shall be placed in the charge of a responsible person and shall
be kept clean.
22. Unauthorized persons - Only maintenance and repair personnel, persons directly
connected with the plant operation and those accompanied by authorized persons shall be
admitted into the plant.
Schedule – XXIII
Operations involving high noise levels
1. Application - This schedule shall apply to all operations in any manufacturing process
having high noise level.
2. Definitions - For the purpose of this schedule -
(a) “Noise” means any unwanted sound.
(b) ”High noise level” means any noise level measured on the A-weighted scale
is 90 dB or above.
(c) ”Decibel” means one-tenth of “Bel” which is the fundamental division of a
logarithmic scale used to express the ratio of two specified or implied quantities, the
number of “Bels” denoting such a ratio being the logarithm to the base the of 10 of this
ratio. The noise level (or the sound pressure level) 6 corresponds to a reference
pressure of 20 x 10 power(-6) Newton per square meter or 0.0002 dynes per square
centimetre which is the threshold of hearing, that is, the lowest sound pressure level
necessary to produce the sensation of hearing in average healthy listeners. The
decibel in abbreviated form is dB.
(d) ”Frequency” is the rate of pressure variations expressed in cycles per
second or hertz.
(e) ”dBA” refers to sound level in decibels as measured on a sound level meter
operating on the A-weighting net work with slow meter response.
(f) ”A-weighting” means making graded adjustments in the intensities of sound
of various frequencies for the purpose of noise measurement, so that the sound
pressure level measured by an instrument reflects the actual response of the human
ear to the sound measured.
3. Protection against noise –
(1) In every factory, suitable, a suitable engineering control or administrative
measures shall be taken to ensure, so far as is reasonably practicable, that no
worker is exposed to sound levels exceeding the maximum permissible noise
exposure levels specified in Tables 1 and 2.
Table 1
Permissible exposure in cases of continuous noise
Total time of exposure (continuous dBA
Sound pressure level in or a per day, in hours
number of short term exposures)
8 90
6 92
4 95
3 97
2 100
1 ½ 102
1 105
¾ 107
½ 110
¼ 115
Notes: 1. No exposure in excess of 115 dBA is to be permitted.
2. For any period of exposure falling in between any figure and the next higher or
lower figure as indicated in column 1, the permissible sound pressure level is to
be determined by extrapolation on a proportionate basis.
Table 2
Permissible exposure levels of impulsive or impact noise
Peak sound pressure level in dB Permitted number of impulses or impact per day
140 100
135 315
130 1,000
125 3,160
120 10,000
Notes: 1. No exposure in excess of 140 dB peak sound pressure level is permitted.
2. For any peak sound pressure level falling in between any figure and the next
higher or lower figure as indicated in column 1, the permitted number of impulses or
impacts per day is to be determined by extrapolation on a proportionate basis.
(3) For the purposes of this schedule, if the variations in the noise level involve
maximum at intervals of one second or less, the noise is to be considered as a
continuous one and the criteria given in Table 1 would apply. In other cases, the noise
is to be considered as impulsive or impact noise and the criteria given in Table 2 would
apply.
(3) When the daily exposure is composed of two or more periods of noise
exposure at different levels their combined effect should be considered, rather than the
individual effect of each. The mixed exposure should be considered to exceed the limit
value if the sum of the fractions C1/T1 + C2/T2 +............ Cn/Tn exceeds unity, -
Where the C1, C2 etc. indicate the total time of actual exposure at a specified
noise level and T1, T2, etc. denote the time of exposure of less than 90 dBA
may be ignored in the above calculation.
(4) Where it is not possible to reduce the noise exposure to the levels specified
in sub-rule (1) by reasonably practicable engineering control or administrative
measures, the noise exposure shall be reduced to the greatest extent feasible by such
control measures, and each worker so exposed shall be provided with suitable ear
protectors so as to reduce the exposure to noise to the levels specified in sub-rule (1).
(5) Where the ear protectors provided in accordance with sub-paragraph (2)
and worn by a worker cannot still attenuate the noise reaching near his ear, as
determined by subtracting the attenuation value in dBA of the ear protectors concerned
from the measured sound pressure level, to a level permissible under Table 1 or Table
2 as the case may be, the noise exposure period shall be suitably reduced to
correspond to the permissible noise exposures specified in sub-paragraph (1).
(6) (a) In all cases where the prevailing sound levels exceed the
permissible levels specified in sub-paragraph (1) there shall be administered an
effective hearing conservation programme which shall include among other hearing
conservation measures, pre-employment and periodical auditory surveys conducted on
workers exposed to noise exceeding the permissible levels, and rehabilitation of such
workers either by reducing the exposure to the noise levels or by transferring them to
places where noise levels are relatively less or by any other suitable means.
(b) Every worker employed in areas where the noise exceeds the maximum
permissible exposure levels specified in sub-rule (1) shall be subjected to
any auditory examination by a Certifying Surgeon within 14 days of his
first employment and thereafter, shall be re-examined at least once a
every 12 months. Such initial and periodical examinations shall include
tests which the Certifying Surgeon may consider appropriate and shall
include determination of auditory thresholds for pure tones of 125, 250,
500, 1000, 2000, 4000 and 8000 cycles per second.
Schedule – XXIV
Manufacture or manipulation of dangerous pesticides
1. Application - This schedule shall apply in respect of all factories or any part
thereof in which the process of manufacture or manipulation of dangerous
pesticide hereinafter referred to as the said manufacturing process is carried on.
2. Definitions - For the purpose of this Schedule -
(a) “dangerous pesticides” means any product proposed or used for
controlling, destroying or repelling any pest or for preventing growth or mitigating
effects of such growth including any of its formulations which is considered toxic under
and is covered by the Insecticides Act, 1968 and the rules made there under and any
other product, as may be notified from time to time by the State Government;
(b) “manipulation” includes mixing, blending, formulating, filling, emptying,
packing or otherwise handling;
(c) “efficient exhaust draught” means localised mechanical ventilation for
removal of smoke, gas, vapour, dust, fume or mist so as to prevent them from
escaping into the air of any work room in which work is carried on. No exhaust
draught shall be considered efficient if it fails to remove smoke generated at the point
where such gas, fume, dust, vapour or mist originates from the process.
3. Instruction to workers - Every worker on his first employment shall be fully instructed on
the properties including dangerous properties of the chemicals handled in the said
manufacturing process and the hazards involved. The employees shall also be instructed in
the measures to be taken to deal with any emergency. Such instructions shall be repeated
periodically.
4. Cautionary notice and placards - Cautionary notices and placards in the form specified in
appendix to this schedule and printed in the language of the majority of the workers shall be
displayed in all work places in which said manufacturing process is carried on so that they can
be easily and conveniently read by the workers. Arrangements shall be made by the occupier
and the manager of the factory to periodically instruct the workers regarding the health
hazards arising to in the said manufacturing process and methods of protection. Such notices
shall include brief instructions regarding the periodical clinical tests required to be undertaken
for projecting health of the workers.
5. Prohibition relating to employment of women or young persons - No woman or young
person shall be employed or permitted to work in any room in which the said manufacturing
process is carried on or in any room in which dangerous pesticide is stored.
6. Food drinks, and smoking prohibition - (1) No food, drink, tobacco, pan or supari shall
be brought into or consumed by any worker in any workroom in which the said manufacturing
process is carried out.
(2) Smoking shall be prohibited in any workroom in which the said manufacturing
process is carried out.
7. Protective clothing and protective equipment - (1) Protective clothing consisting
of long pants and shirts or overalls with long sleeves and head coverings shall be
provided for all workers employed in the said manufacturing process.
(2) (a) Protective equipment consisting of rubber gloves, gum boots, rubber
aprons, chemical safety goggles and respirators shall be provided for all
workers employed in the said manufacturing process.
(b) Gloves, boots, aprons shall be made from synthetic rubber where a
pesticide contains oil.
(3) Protective clothing and equipment shall be worn by the workers supplied
with such clothing and equipment.
(4) Protective clothing and equipment shall be washed daily from inside and
outside if the workers handle pesticides containing nicotine or phosphorous and shall
be washed frequently if handling other pesticides.
(5) Protective clothing and equipment shall be maintained in good condition.
8. Floors and work-benches - (1) Floors in every workroom where dangerous pesticides
are manipulated shall be of cement or other impervious material giving a smooth
surface.
(2) Floors shall be maintained in good repair, provided with adequate slope leading
to a drain and thoroughly washed once a day with the hose pipe.
(3) Work-benches where dangerous pesticides are manipulated shall be made of
smooth, non-absorbing material preferably stainless steel and shall be cleaned
at least once daily.
9. Spillage and waste - (1) If a dangerous pesticide during its manipulation splashes or
spills on the work-bench, floor or on the protective clothing worn by a worker,
immediate action shall be taken for through decontamination of such areas or articles.
(2) Cloth, rags, paper or other material soaked or soiled with a dangerous
pesticide shall be deposited in a suitable receptacle with tight fitting cover.
Contaminated waste shall be destroyed by burning at least once a week.
(3) Suitable deactivating agents, where available, shall be kept in a readily
accessible place for use while attending to a spillage.
(4) Easy means of access shall be provided to all parts of the plant for
cleaning, maintenance and repairs.
10. Empty containers used for dangerous pesticides - Containers used for dangerous
pesticides shall be thoroughly cleaned of their contents and treated with an inactivating
agent before being discarded or destroyed.
11. Manual handling - (1) A dangerous pesticide shall not be required or allowed to be
manipulated by hand except by means of a long handled scoop.
(2) Direct contact of any part of the body with a dangerous pesticide during its
manipulation shall be avoided.
12. Ventilation - (1) In every workroom or area where a dangerous pesticide is
manipulated, adequate ventilation shall be provided at all times by the circulation of
fresh air.
(2) Unless the process is completely enclosed, the following operations during
manipulation of a dangerous pesticide shall not be undertaken without an
efficient exhaust draught :-
(a) emptying a container holding a dangerous pesticide;
(b) blending a dangerous pesticide;
(c) preparing a liquid or powder formulation containing a dangerous pesticide;
and
(d) Changing or filling a dangerous pesticide into a container, tank hopper or
machine or small sized containers.
(3) In the event of a failure of the exhaust draught provided on the above operation,
the said operations shall be stopped forthwith.
13. Time allowed for washing - (1)Before each meal and before the end of the day’s
work at least ten minutes in addition to the regular rest interval shall be allowed for
washing to each worker engaged in the manipulation of dangerous pesticide.
(2) Every worker engaged in the manipulation of dangerous pesticides shall have a
thorough wash before consuming any food and also at the end of the day’s work.
14. Washing and bathing facilities - (1) There shall be provided and maintained in a
clean state and in good repair for the use of all workers employed in the factory where
the said manufacturing process is carried on, adequate washing and bathing places
having a constant supply of water under cover at the rate of one such place for every 5
persons employed.
(2) The washing places shall have standpipes placed at intervals of not less
than one meter.
(3) Not less than one half of the total number of washing places shall be
provided with bathrooms.
(4) Sufficient supply of clean towels made of suitable material shall be provided
:
Provided that such towels shall be supplied individually for each worker is so
ordered by the Inspector.
(5) Sufficient supply of soap and nail brushes shall be provided.
15. Cloakroom - There shall be provided and maintained for the use of all workers
employed in the factory where the said manufacturing process is carried on -
(a) a cloakroom for clothing put off during working hours with adequate
arrangements for drying clothing, if wet; and
(b) separate and suitable arrangements for the storage of protective clothing
provided under paragraph 7.
16. Mess room - (1) There shall be provided and maintained for the use of all workers
employed in the factory in which the said manufacturing process is carried on and
remaining on the premises during the rest intervals, suitable mess room which shall be
furnished with -
(a) sufficient tables and benches with back rest, and
(b) Adequate means for warming food.
(2) The mess room shall be placed under the charge of responsible person and shall
be kept clean.
17. Manipulation not be undertaken - Manufacture or manipulation of a pesticides shall
not be undertaken in any factory unless a certificate regarding its dangerous nature or
otherwise is obtained from the Chief Inspector.
18. Medical facilities and records of examinations and tests - (1) The occupier of every
factory to which this schedule applies, shall -
(a) employ a qualified medical practitioner for medical surveillance of the
workers employed therein whose employment shall be subject to the approval of the
Chief Inspector of Factories; and
(b) Provide to the medical practitioner all the necessary facilities for the
purpose referred to in clause (a).
(2) The record of such examinations carried out by the medical practitioner shall be
maintained in a separate, register approved by the Chief Inspector of Factories,
which shall be kept readily available for inspection by the Inspector.
19. Medical examination by certifying Surgeon - (1) every worker employed in the
processes specified in paragraph 1 shall be examined by a Certifying Surgeon within
15 days of his first employment. Such examinations in respect of Halogenated
Pesticides,shall include tests for determination of chemical in blood and in fat tissues,
E.E.G. abnormalities and memory tests.In respect of organo phosphate
compounds,such examinations shall include tests for depression of cholinesterase in
plasma and red blood cells. No worker shall be allowed to work after 15 days of his first
employment in the factory unless certified fit for such employment by the Certifying
Surgeon.
(2) Every worker employed in the said process shall be re-examined by a
Certifying Surgeon at least once in every six calendar months. Such examination shall,
wherever the Certifying Surgeon considers appropriate, include the tests specified in
sub-paragraph (1). Further every worker employed in the said processes shall also be
examined once in every three months by the factory medical officer.
(3) The Certifying Surgeon after examining a worker, shall issue a Certificate
of Fitness in Form 32. The record of examination and re-examinations carried out
shall be entered in the Certificate and the Certificate shall be kept in the custody of
the manager of the factory. The record of each examination carried out under sub-
paragraph (1) and (2), including the nature and the results of these test, shall also
be entered by the certifying Surgeon in a health register in Form 17.
(4) The Certificate of Fitness and the health register shall be kept readily
available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a worker is no
longer fit for employment in the said processes on the ground that continuance therein
would involve special danger to the health of the worker, he shall make a record of his
findings in the said certificate and the health register. The entry of his findings in
those documents should also include the period for which he considers that the
said person is unfit to work in the said process shall be provided with alternate
placement facilities unless he is fully incapacitated in the opinion of the Certifying
Surgeon, in which case the person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in sub-paragraph (5)
shall be re-employed or permitted to work in the said processes unless the Certifying
Surgeon, after further examination, again certifies him fit for employment in those
processes.
20. Exemption - If in respect of any factory the Chief Inspector is satisfied that owing to the
exceptional circumstances or the infrequency of the said manufacturing process or for
any other reason which shall record in writing all or any of the provisions of this
schedule are not necessary for the protection of workers employed in the factory, he
may by a certificate in writing exempt such factory, from all or any of the provisions on
such condition as he may specify therein
Previous and next
Questions people ask
Is appendix B of Punjab Factories Rules 1952 still in force?
No repeal of Punjab Factories Rules 1952 is recorded.