Rule 31, Delhi Factories Rules, 1950: Prevention of glare
Delhi Factories Rules, 1950 - Rule 31
Text of rule 31
Prevention of glare
31.Prevention of glare--
(1) Where any source of artificial light in the factory is less than 16 feet above floor
level, no part of the light source or of the lighting fitting having a brightness greater
than 10 candles per square inch shall be visible to persons whilst normally employed
within 100 feet of the source, except where the angle of elevation from the eye to
the source or part of the fitting as the case may be exceeds 20°.
(2) Any local light that is to say an artificial light designed to illuminate particularly the
area or part of the area of work of a single operative or small group of operatives
working near other, shall be provided with a suitable shade of opaque material to
prevent glare or with other effective means by which the light source is completely
screened from the eyes of every person employed at the normal working place, or
shall be so placed that no such person is exposed to glare therefrom.
CHAPTER IV
SAFETY
Further precautions prescribed under sub-section (2) of Section 21
52. Further safety precautions-
(1) Without prejudice to the provisions of sub-section (1) of Section 21 in regard to
the fencing of machines the further precautions specified in the Schedules
annexed hereto shall apply to the machines noted in each Schedule.
(2) This Rule shall come into force, in respect of any class or description of factories,
where machines noted in the said Schedules are in use, on such dates as the
Chief Commissioner may, by notification in the official gazette, appoint in this
behalf.
SCHEDULE I
COTTON TEXTILES
1. Cotton Openers, Scutchers, Combined Openers and Scutcher and Lap
Machines, Hard Waste breakers, etc.-
(1) All Cotton Openers, Scutchers, Combined Openers and Scutchers, Scutchers and
Lap Machines, Hard Waste Breakers and similar machines shall be driven by
separate motors or from counter shafts provided with fast and loose pulleys and
efficient belt shifting devices.
(2) In all Openers, Combined Openers and Scutchers, Scutchers, Scutchers- lap
machines, Hard Waste Breakers and similar machines, the beater covers and
doors which give access to any dangerous part of the machine shall be fitted
with effective interlocking arrangements which shall prevent-
(a) the covers and doors being opened while the machine is in motion;
(b) the machine being re-started until the covers and doors are close ;
Provided that in respect of doors of openings, other than dirt doors or
desk doors such openings shall be so fenced as to prevent access to any
dangerous part of the machine if effective interlocking arrangement is not
provided.
(3) In all Openers, Combined Openers and Scutchers, Scutchers, Scutcher-lap
machines, Hard waste Breakers and similar machines, the openings giving
access to the dust chamber shall be provided with permanently fixed fencing,
which shall, while admitting light, yet prevent contact between any portion of a
worker's body and the beater grid bars.
Provided that the latter requirement in respect of the automatic locking device
shall not apply while stripping or grinding operations are carried out.
Provided further the stripping or grinding operations shall be carried out only by
specially trained adult workers wearing tight fittings clothing whose names have
been recorded in the register prescribed in this behalf as required in sub-section
(1) of Section 22.
2. Combined Openers and Scutchers, Scutcher-lap, Silver Lap, Lap Machines,
Dorby Doublers and Ribbon Machines-
(1) The lap forming rollers shall be fitted with a guard or cover which shall prevent
access to the intake of the lap roller and fluted roller as long as the weighted
rack is down; or
(2) The guard or cover shall be so locked that it cannot be raised until the machine
is stopped and the machine cannot be started until the guard or cover is closed.
3. Carding Machines-
All Cylinder doors shall be secured by an automatic locking device which shall prevent
the door being opened until the cylinder has ceased to revolve and shall render it
impossible to restart the machine until the door has been closed.
4. Speed Framers-
Headstocks shall be fitted with automatic locking arrangements which shall prevent the
doors giving access to jack box wheels opened while the machinery is in motion and
shall render it impossible to restart the machine until the doors have been closed.
5. Self-acting Mules-
The drive shall be from counter-shafts which shall be provided with fast and loose
pulleys and efficient belt shifting devices.
6. Calendering Machines etc.-
In respect of calendering machines, mangles and similar machines, all such machines
shall be provided with an efficient "nip" guard along the whole length on the intake side
of each pair of bow Is and similar parts which shall be so fitted and maintained, whilst
the rollers of bowls are in motion, as to prevent access to the point of contact of the
rollers or bowls.
SCHEDULE II
Cotton Ginning
Line Shaft-
The line shaft or second motion in cotton ginning factories, when below floor level, shall
be completely enclosed by a continuous wall or unclimable fencing with only so many
openings as are necessary for access to the shaft for removing cotton seed, cleaning
and oiling; and such openings shall be provided with gates or doors which shall be kept
closed and locked.
SCHEDULE III
Wood-Working Machinery
1. Definition- For the purposes of this Schedule :-
http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//factoryrules/
(a) Wood-Working machine means a circular saw, band saw, planning machines,
chain mortising machine or vertical spindle moulding machine operating of Wood
or Cork.
(b) Circular saw means a circular saw working in a bench (including a rack bench)
but des not include a pendulum or similar saw which is moved towards the wood
for the purpose of cutting operation.
(c) BaI1d saw means a band saw, the cutting portion of which runs in a vertical
direction but does not include a log saw or band resawing machine.
(d) Planning machine means a machine for overhand plannings or for thicknessing
or for both operations.
2.
An efficient stopping and starting device shall be provided on every wood-working
machine. The control of this device shall be in such a position as to be readily and
conveniently operated by the person in charge of the machine.
3. Space around machines-
The space surrounding every wood-working machine in motion shall be kept free from
obstruction.
4. Floors-
The floor surrounding every wood-working machine shall be maintained in good and
level condition, and shall not be allowed to become slippery, and as far as practicable
shall be kept free from chips or other loose material.
5. Training and Supervision-
(1) No person shall be employed at a wood - working machine unless he has been
sufficiently trained to work that class of machine, or unless he works under the
adequate supervision of person who has a thorough knowledge of the working of
the machine.
(2) A person who is being trained to work a wood-working machine shall be fully
and carefully instructed as to the dangers of the machine and the precautions to
be observed to secure safe working of the machine.
6. Circular Saws-
Every circular saw shall be fenced as follows:-
(a) Behind and in direct line with the saw there shall be a riving knife, which shall
have a smooth surface, shall be strong rigid and easily adjustable, and shall also
conform to the following conditions :
(i) The edge of the knife nearer the saw shall from an area of a circle having
a radius not exceeding the radius of the largest saw used on the bench.
(ii) The knife shall maintained as close as practicable to the saw having
regard to the nature of the work being done at the time and at the level
of the bench table the distance between the front edge of the knife and
the teeth of the saw shall not exceed half an inch.
(iii) For a saw of a diameter of less than 24 inches, the knife shall extent
upwards from the bench table to within one inch of top of the saw and for
a saw of a diameter of 24 inches or over shall extend upwards from the
bench table to a height of at least nine inches.
(b) The top saw shall be covered by a strong and easily adjustable guard, with a
flange at the side of the saw farthest from the fence. The guard shall be kept so
adjusted that the said flange shall extend below the roots of the teeth of the
saw. The guard shall extend from the top of the riving knife to a point as point
as practicable at the cutting edge of the saw.
(c) The part of the saw below the bench table shall be protected by two plates of
metal or other suitable material one on each side of the saw; such plates shall
not be more than six inches apart, and shall extend from the axis of the saw
outwords to a distance of not less than two inches beyond the teeth of the saw.
Metal plates, if not beaded, shall be of a thickness of at least 1/10 inch, or if
beaded be of a thickness of at least 1/20 inch.
7. Push Sticks-
A push stick or other suitable appliance shall be provided for use at every circular saw
and at every vertical spindle moulding machine to enable the work to be done without
unnecessary risk.
8. Band Saws-
Every band saw shall be guarded as follows :-
(a) Both sides of the bottom pulley shall be completely encased by sheet or
expanded metal or other suitable material.
(b) The front of the top pulley shall be covered with sheet or expended metal or
other suitable material.
(c) All portions of the blade shall be enclosed or otherwise securely guarded except
the portion of the blade between the bench table and the top guide.
9. Planning Machines-
(1) A planning machine (other than a planning machine which is mechanically fed)
shall not be used for overhand planning unless it is fitted with a cylindrical cutter
block.
(2) Every planning machine used for overhand planning shall be provided with a
"brige" guard capable of covering the full length and breadth of the cutting slot
in the bench and so constructed as to be easily adjusted both in a vertical and
horizontal direction.
(3) The fee roller of every planing machine used for thicknessing except the
combined machine for overhand planing and thicknessing, shall be provided with
an efficient guard.
10. Vertical Spindle moulding machines-
(1) The cutter of every vertical spindle moulding machine shall be guarded by the
most efficient guard having regard to the nature of the work being performed.
(2) The wood being moulded at a vertical spindle moulding machine shall, if
practicable, be held in a zig or holder of such construction as to reduce as far as
possible the risk of accident to the worker.
11. Chain mortising machines-
The chain of every chain mortising machine shall be provided with a guard which shall
enclose the cutters as far as practicable.
12. Adjustment and maintenance of guards-
The guards and other appliance required under this Schedule shall be-
(a) maintained in an efficient state,
(b) constantly kept in position while the machinery is in motion, and
(c) so adjusted as to enable the work to be done without unnecessary risk.
18. Exemptions-
Paragraphs 6, 8, 9 and 10 shall not apply to any wood working machine in respect of
which it can be proved that other safeguards are provided, maintained and used which
render the machine as safe as it would be if guarded in the manner prescribed in this
Schedule.
http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//factoryrules/
CHAPTER V
WELFARE
Rules prescribed under sub-section 2 of Section 42
62. Washing facilities-
(1) This rule shall come into force, in respect of any class or description of factories,
on such dates as the Chief Commissioner may, by notification in the official
gazette, appoint in this behalf.
(2) There shall be provided and maintained in every factory for the use of employed
persons adequate and suitable facilities for washing which shall include soap and
nail brushes or other suitable means of cleaning and the facilities shall be
conveniently accessible and shall be kept in a clean and orderly condition.
(3) Without prejudice to the generality of the foregoing provisions the washing
facilities shall include:-
(a) a trough with taps or jets at intervals of not less than two feet, or
(b) wash-basins with taps attached thereto, or
(c) taps on stand-pipes, or
(d) showers controlled by taps, or
(e) circular troughs of the fountain type.
Provided that the Inspector may, having regard to the needs and habits of the
workers, fix the proportion in which the aforementioned types of facilities shall be
installed,
(4) (a) Every trough and basin shall have a smooth, impervious surface and shall
be fitted with a waste-pipe and plug,
(b) The floor or ground under and in the immediately vicinity of every trough
tap, jet, wash basin, standpipe and shower shall be so laid or finished as to
provide a smooth impervious surface and shall be adequately drained,
(5) For persons whose work involves contact with any injurious or noxious substance
there shall be at least one top for every fifteen persons; and for persons whose
work does not involve such contact the number of taps shall be as follow :-
No. of Workers No. of Taps
Upto 20 1
21 to 35 2
36 to 50 3
51 to 150 4
151 to 200 5
Exceeding 200 but not exceeding
500
5 plus one top for every 50 or fraction of 50
Exceeding 500 11 plus one top for every 100 or fraction of
100
(6) If female workers are employed, separate washing facilities shall be provided and
so enclosed or screened that the interiors are not visible from any place where
persons of the other sex work or pass. The entrance to such facilities shall bear
conspicuous notice in the language understood by the majority of the workers
"For Women Only" and shall also be indicated pictorially,
(7) The water supply to the washing facilities shall be capable of yielding at least six
gallons a day for each person employed in the factory and shall be from a source
approved in writing by the Health Officer, provided that where there the Chief
Inspector is satisfied that such an yield is not practicable he may by certificate in
writing permit the supply of a smaller quantity not being less the then one gallon
per day for every person employed in the factory,
Rules Prescribed Under Section 43
62-
A.
The following classes of factories shall provide therein suitable place for
keeping clothing not work during working hours and for the drying of wet
clothing:-
(1) Glass Factories.
(2) Iron & Steel Factories.
(3) Oil Mills.
(4) Chemical Factories.
(5) Automobile Workshops.
Rule prescribed under sub-section (1) of Section 45.
Previous and next
← Rule 24Thermometers to be maintained in efficient order- Each thermometer shall be maintained at all times during the period of employment in efficient working order, so as to give accurate indications and in particularRule 63 →First Aid Appliance- The first aid boxes or cup-boards shall be distinctively marked with a red cross on a white ground and shall contain the following equipment
Questions people ask
Is rule 31 of Delhi Factories Rules, 1950 still in force?
No repeal of Delhi Factories Rules, 1950 is recorded.