Form OF CERTIFICATE OF COMPETENCY ISSUED TO A, The Tamil Nadu Factories Rules,1950: FORM OF CERTIFICATE OF COMPETENCY ISSUED TO A
The Tamil Nadu Factories Rules,1950 - Form OF CERTIFICATE OF COMPETENCY ISSUED TO A
Text of form OF CERTIFICATE OF COMPETENCY ISSUED TO A
FORM OF CERTIFICATE OF COMPETENCY ISSUED TO A
FORM OF CERTIFICATE OF COMPETENCY ISSUED TO A
PERSON OR AN INSTITUTION IN PURSUANCE TO RULE 2-A
MADE UNDER SECTION 2(ca)
I, in exercise of the powers conferred on me under Section 2( ca)
of the Factories Act and the rules made thereunder, hereby recognise
............. (Name of the Institution) or Thiru (Name of the person)
employed in (Name of the Organisation) to be a competent person for
the purpose of carrying out tests, examinations, inspections and certifications
for such buildings, dangerous machinery, lifts and hoists, lifting machines·
and lifting tackles, confined space, ventilation system and process· or plant
and equipment as the casemaybe used ina factory located in under section
and the rules made thereunder.
This certificate is valid from to
This certificate is issued subject to the conditions stipulated thereun-
·der-
(i) Tests, examinations and inspections shall be carried out in ac
cordance with the provisions of the Act and the rules made thereunder.
(ii) Tests, examination and inspections shall be carried out under·
direct supervision of the competent person or by a person so authorised by .
an institution recognised to be a competent person.
(iii) The certificate of competency issued in favour of a person .
shall stand cancelledif the person leaves the organisation mentioned in his
application.
(iv) The institution recognised as a competent person shall keep
the Chief Inspector informed of the names, designations and qualifications
of the person authorised by it to carry out tests, examinations and inspections.
(v)
(vi)
(Strike out the words not applicable)
Station:
Office Seal :
Date:
Note : A separate certificate should be issued under each relevant section. A
person or an institution may be recognised competent for the purpose of more
than one section of the Act.
Signature of the Chief Inspector
-
·
-
-
-
-
-
·-
-
-
-
-
-
-
-
-
-
-
-
·-
-
-
.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
··--
-
-
-
-
-
-
-
-
V)
-
.:?
-
-
tr)
-
•
...
u
•
�
�
�
.s
"Cl
�
o
=
�
e
-
"'
....
::,
O
O
Cl
u
>
�
....
0
-
.
...
-
I
s
=
·;
El
::
--
-
N
-
-
-
-
"Cl
= =
-
N
-
-
-
.._.
·c
:�
0
1;l
..:
"O
.,:;
...
B
B
!a
·5
::3
"'
s
.;!
;;,..,
<.:
"'
E
·"Si
.S:?
I!)
"'
...
:€
-0
o
e
Q.
0
�
0
-0
...
.
'G
r::
·;;
-5
.e
�
g_
.
.....
"'
!!l
O
"'
�
1il
B
.s
I!)
·.;::
ob
e
�
s
8.
·c:;
·i
]
:S
0
.c
o:s
o:s
·-
.c
t(l
u..
..J
�
�
,;::::
0
0
...
bl)
0
-0
..
0
00
i:
·.:
u
u
.
i:
...:
�
:.:
"O
Q.
§
i ..
....
,'!)
0
§
�
.5
.§" �
.E
i:
8
0
-
u
-�
...
0
.c
....
0
...
0
c:
0
>
0
"'
.....
0
0
•
I
"'O
0
"'O
:i
II")
·
-
a
"'O
0
"'O
;
�
o:s
0
E
...
0
Q..
�
c
,E
.c
�
>
o:s
c:
"'O
Q.
....
c:
c
·;;
i
o:s
.....
0
in
0
E
...
°'
Q..
Oil
ri
_.-
.§
c
-�
E
0
0
"j
:i
>
"'
-�
::s
O
"'
x
�
c
g-
<!::
Q.
....;
-
1[3.Approval of site, construction or
extension of a factory. — 2[3[(1) (a)] No site shall be
used for the location of a factory or no building in a
factory be constructed, reconstructed extended or taken into
use as a factory or part of a factory, or no installation of
plant or machinery carried out in a factory without the previous permission in
writing of the 4[Chief Inspector or Deputy Chief Inspector as the case may be].
The previous permission of the 4[Chief Inspector or Deputy Chief Inspector as
the case may be] shall also be obtained for the installation of additional machinery
or for the installation of prime movers exceeding the horse-powers already
installed in the factory.]
5[(b) The 4[Chief Inspector or Deputy Chief Inspector as the case may
be] may require, for the purpose of the Act, submission of plans of any
factory which was either in existence on the date of commencement of the
Act or which has not been constructed or extended since then.]
8[(a) a flow chart of the manufacturing process supplemented
by a brief description of the process in its various stages, including the
chemicals used, if any, in the various stages of the process and the steps
proposed to be taken for effective removal of dust, fumes, gases and regarding
the proper and effective disposal of trade wastes and effluents ] ;
(b) plans in triplicate drawn to scale showing —
1Rules 3 and 4, substituted by GO. Ms. No. 866, Industries, Labour and Cooperation,
dated the 13th February, 1961.
2Subs. by GO. Ms. No. 1523, Labour and Employment, dated the 10th July, 1980.
3Sub-rule (1), re-numbered as (1) (a), by GO. Ms. No. 2013, Labour and
Employment, dated the 30th August, 1980.
4 Subs. by G.O. Ms. No. 2844, Labour and Employment, dated the 17th December,
1980, for " Chief Inspector ".
5 Ins. by GO. No. 2013, Labour and Employment, dated the 30th August, 1980.
6Subs. by GO. No. 2013, Labour and Employment, dated the 30th August, 1980, for
"Application for such permission shall be made in in Form No.1 in triplicate ".
8Clause (a), substituted by GO. Ms. No. 3681, Industries, Labour and Housing (Labour),
dated the 31st October, 1969.
Rules 3 to 11
p r e s c r i b e d
u n d e r s u b -
section (1) of
section 6.
THE TAMIL NADU FACTORIES RULES, 1950 [R.3
(2) 6[Application for such permission or submission of plans shall be
made 7[in Form No.1 through online portal of Directorate of Industrial Safety
and Health] It shall be accompanied by the following documents, namely : —
7Ins. by G.O. Ms. No. 15, Labour and Employment (M2), dated 31st January 2018.
(i) the site of the factory and immediate surroundings inclu
ding adjacent buildings and other structures, roads, drains, and the like ;
and
. (ii) the plan elevation and necessary cross sections of
various buildings indicating all relevant details relating to natural
lighting, ventilation and means of escape in case of fire. The plans shall
also clearly indicate the position of the plant and machinery, aisles and
passageways.
'[* * *]
( c) 2[ Omitted]
3[(d)] a certificate from the 4[Tamil Nadu Pollution Control Board,
Madras], to the effect that the arrangements made for disposal of industrial
liquid wastes, effluents and air pollutants in the case of complex chemical
factories and regarding the steps taken for proper disposal of wastes and
effluents are effective ;
5[(e)] such other particulars as the, 6(Chief Inspector or Deputy
Chief Inspector, as the case may be] may require.
'[Provided that where an application for such permission has been
made in the common application form for single window clearance
approved in GO. Ms. No. 203, Industries (MIB - I) Department, dated 24th
December, 2001 then making of an application in Form No. I is not
necessary.].
I Proviso to clause (b) initially added by GO. Ms. No. 3681, Industries, Labour and
Housing (Labour), dated the 31st October, 1969, subsequently omitted by GO. Ms.
No. 1523, Labour and Employment, dated the 10th July, 1980.
2 Clause (c), omitted by notification.
3 Clause "(d) ", inserted after the-initial clause" (d)" alongwith its contents re
lettered as clause (e) ", by GO. MS. No. 3681, Industries, Labour and Housing
(Labour), dated the 31st October, 1969.
•Subs.by GO. Ms. 1462, Labour, dated the 14th July, 1987, for" Director of Health
Services and Family Planning, Madras".
s Re-lettered for the then existing clause" (d) ", by GO. Ms. No. 3681, Industries,
Labour and Housing (Labour), dated the 31st October, 1969.
6 Subs. by GO. Ms. No. 2844, Labour and Employment, dated the 17th December,
1980, for " Chief Inspector ".
7 Added by G.0. Ms. No. 148, Labour and Employment (M-2), dated the 12th
October, 2009.
/ R . 3 ] THE TAMIL NADU FACTORIES RULES, 1950
[R.3
Provided further that the 2[Chief Inspector or Deputy Chief Inspector,
as the case may be] may accord such permission subject to such conditions
as he may consider necessary.
(4) The fact that the permission applied for is accorded shall be
noted on the plans and specifications and shall be signed by the
2[Chief Inspector or Deputy Chief Inspector, as the case may be]. One copy
of each of the said plans and specifications shall be returned to the
applicant.
4. Registration and grant of licence for a factory. --
(1) No premises shall be used as factory, nor any manufacturing process
carried on in any factory except under, and in accordance with, the
registration and licence granted under these rules.
(3) The fees payable for the registration and grant of a licence
(3) After examination of the documents referred to in sub-rule
(2), the 2[Chief Inspector or Deputy Chief Inspector, as the case may be]
Provided that the 2[Chief Inspector or Deputy Chief Inspector as the
case may be] may call for such other particulars as he may require before
according such permission :
(5) (a) A factory or part of a factory constructed, reconstructed,
extended or taken into use, shall be in accordance with the plans appro-
ved by the 2[Chief Inspector or Deputy Chief Inspector, as the case
may be] and shall satisfy the conditions subject to which the plans have
been approved.
(b) No machine or prime mover or a permanent fixture not
shown in the plans approved by the 2[Chief Inspector or Deputy Chief
Inspector, as the case may be] shall be installed, fixed or used in any
factory except in replacement of any machine, prime mover or a perma-
nent fixture not occupying more floor area than that already shown in
the approved plans.
THE TAMIL NADU FACTORIES RULES, 1950
1[shall accord the permission applied for within thirty days from the
date of receipt of such application:]
(2) An application for the registration of a factory and grant of a
licence to it shall be submitted to the Chief Inspector 3[in Form No.2
through online portal of Directorate of Industrial Safety and Health].
to a factory shall be as specified in the schedule hereto. The application
3 Subs. by G.O. Ms. No. 15, Labour and Employment (M2), dated 31st January 2018.
1Ins. by G.O. Ms. No. 105, Labour and Employment (M1), dated the 25th May 2017.
2Subs. by Go. Ms. No. 2844, Labour and Employment, dated
the 17th December, 1980, for " Chief Inspector ".
(4) Every application received by the Chief Inspector shall be
registered in Form No. 3.
(5) No licence shall be granted until the notice specified in
section 7 has been received in triplicate in Form No. 2 by the Chief
Inspector.
(6) If the Chief Inspector is satisfied that the registration and licence
may be granted, such registration and licence shall be issued in FormNo.4
Provided that the Chief Inspector may call for such other particulars as he
may require before registration or grant of such licence :
Provided further that the Chief Inspector may register and grant licence
subject to such conditions as he may consider necessary and which shall be
specified in the licence.
3
(7) Except as provided in 4[rule 7AA or 109] every licence
granted or renewed under this chapter shall remain in force upto and inclusive
of the 31st December of the year for which the licence is granted or renewed.]
1Subs by GO. Ms. No. 150, Labour and Employment (M-11), dated the 14th July, 1993,
for "by a treasury receipt "
2Subs. by GO. Ms. No. 149, Labour and Employment (M-2), dated the 25th July, 1995,
for "crossed demand ".
3Ins. by GO. Ms. No. 150, Labour and Employment (M-11), dated the 14th July,
1993
4 Subs. by GO. Ms. No. 24, Labour and Employment (M-2), dated the 12th
February, 1993, for" rule 109 ".
R.3] THE TAMIL NADU FACTORIES RULES, 1950
in Form No. 2 shall be accompanied 1[by a 2[treasury receipt or by crossed demand
draft] drawn in any branch of a Nationalised Bank in favour of the Deputy Chief
Inspector of Factories of the region] 5[or by online payment through online portal
of Directorate of Industrial Safety and Health] evidencing payment of the appropriate
fee specified in the schedule hereto.
6[within thirty days from the date of receipt of application referred to in sub-rule
(2):]
[(6-A) The Occupier of a factory may opt to remit the licence fees for
obtaining initial licence or renewal of licence for a period upto 7[ten consecutive
calendar years], instead of getting it renewed for every calendar year. Occupier
shall make a specific request in Form No. 2 indicating the number of years for
which licence is sought for. In such cases the fees payable for the grant or
renewal of licence to a factory shall be proportionate to the annual fees as
per the Schedule multiplied by the number of years for which the licence is
sought for]
7Subs.. by GO. Ms. No. 15, Labour and Employment (M 2), dated the 31st January,
2018 for “ five consecutive calendar years”.
5Ins. by GO. Ms. No. 15, Labour and Employment (M 2), dated the 31st January, 2018.
6Ins. by GO. Ms. No. 105, Labour and Employment (M 1), dated the 25th May, 2017.
1
[THE SCHEDULE]
Total Horse Power installed
inclusive of Mobile Equipment
Maximum number of Persons to be employed on any day during the year
9 20 50 100 250 500 1000 2000 5000 10000 Above
10000
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)
(Fee Payable in Rupees)
Nil Horse Power
800
1600 2400 3200 7200 10800 24000 36000 66000 96000 120000
Upto 10 Horse Power
1600
2400
3200 4800 10800 18000 48000 72000 108000 144000 180000
Above 10 Horse Power
Upto 50 Horse Power 2400 3200 4800 7200
18000
28800 72000 108000 144000 180000 216000
Above 50 Horse Power
Upto 129 Horse Power 3200 4800 7200 12000 28800 48000 108000 144000 180000 216000 240000
Above 129 Horse Power
Upto 250 Horse Power 4800 7200 12000 19200 48000 72000 144000 180000 216000 240000 264000
Above 250 Horse Power
Upto 500 Horse Power 7200 12000 16000 25600 72000 96000 180000 216000 240000 264000 288000
Above 500 Horse Power
Upto 1000 Horse Power 12000 12800 25600 48000 96000 120000 216000 240000 264000 288000 312000
Above 1000 Horse Power
Upto 2000 Horse Power 12800 25600 48000 64000 120000 144000 240000 264000 288000 312000 336000
Above 2000Horse Power
Upto 5000 Horse Power 25600 48000 64000 80000 144000 168000 264000 288000 312000 336000 360000
Above 5000 Horse Power
Upto 7500 Horse Power 48000 64000 80000 96000 168000 192000 288000 312000 336000 360000 384000
Above 7500Horse Power
Upto 10000 Horse Power 64000 80000 96000 112000 192000 216000 312000 336000 360000 384000 408000
Above 10000 Horse Power
80000 96000 112000
128000
216000 240000 336000 360000 384000 408000 432000
Subs. by G.O. Ms. No. 132, Labour and Employment (M2), 28th September 2018. (With effect from 1st January 2019)
5. [Omitted]
6. Amendment of licence.--(1) The limits specified in the
licence granted to a factory in regard to horse power or the number of
persons employed shall not be altered or the name, of the factory changed
unless the licence has been amended by the 1[Deputy Chief Inspector of
Factories] having jurisdiction over the area where the factory is situated.
3
(3) The fee for the amendment of a licence shall be 4[fifty
rupees] plus the amount, if any, by which the fee that would have been
payable if the licence had originally been issued in the amended
form exceeds the fee originally paid for the licence.
(4) On the receipt of such application together with the fee
prescribed, the 1[Deputy Chief Inspector of Factories] may amend the
licence suitably :
Provided the 1[Deputy Chief Inspector of Factories] may call for
such other particulars as he may require before amending the licence:
Provided further that the 1[Deputy Chief Inspector of
Factories] may amend the licence subject to such conditions as he may
consider necessary and which shall be specified in the licence.
(5) The amendment made shall be incorporated in the
licence and the Register of Factories.
5[(6) No fee for the amendment of a licence shall be
payable when the amendments are proposed simultaneously with the
application for the renewal of the licence.]
__________________________________________________________
1Subs. by G O. Ms. No 2844 Lab. & Emp , dated 17-12- 1980.
2Subs. by G.O. Ms. No.149, Lab. & Emp. (M-II), dated 25-7-1995 ** Omitted
ibid.
3Subs. by G.O. Ms. No.150, Lab. & Emp. (M-1T), dated 14-7-1993.
4Subs. by G.O. Ms. No.74, Lab. & Emp. (M-II), dated 16-4-1993.
5Ins. by G.O. Ms. No.109, Labour, dated the 23rd January, 1985.
(2) An application for the amendment of a licence granted to a
factory shall be submitted to the 1[Deputy Chief Inspector of Factories]
having jurisdiction over the area where the factory is situated, specifying
the nature of the amendment sought and the reasons therefore, at least
fifteen days prior to the date on which the applicant desires the
amendment to take effect. The application shall be accompanied by
the original licence, if it is not already available with the 1[Deputy Chief
Inspector of Factories,] 2[and
TAMIL NADU FACTORIES Rules, 1950 [R.6
[treasury receipt or a crossed demand
draft] of any branch of a Nationalized Bank drawn in favour of the Deputy
Chief Inspector of Factories of the region] 6[or by online payment through
online portal of Directorate of Industrial, Safety and Health].
6Ins. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January 2018.
7. Renewal of licence.--(1) No premises shall be used as a
factory nor any manufacturing process carried on in any factory
except under, and in accordance with, the licence renewed under
these rules.
2(3) The same fee shall be charged for the renewal of a
licence as for the grant thereof :
Provided that if the application for renewal is not received within
the time specified in sub-rule (2), the licence shall be renewed only
on payment of an additional fee of--
(1) ten percentum of the fee payable, if the application for the
renewal is received in the month of November of the year for which the
licence is granted or renewed.
(2) twenty percentum of the fee payable if the application for
renewal is received in the month of December of the year for which the
licence is granted or renewed.
(3) thirty percentum of the fee payable, if the application for
renewal is received after the expiry of the licence :
3 [***]
4[Provided further that ]if the occupier of the factory opts to remit
(4) If the application has been made in accordance with this rule,
the premises shall be held to be duly licensed until such date as the
1[Deputy Chief Inspector of Factories] may pass orders on the
application for the renewal
1 Subs. by G.O. Ms. No.2844, Lab. & Emp., dated 17-12-1980.
2 Subs. by G.O. Ms. No.150, Lab. & Imp. (M-11), dated 14-7-1993.
3 Omitted by G.O. Ms. No.149, Lab. & Emp. (M-11) dated 25-7-1995
4 Subs. ibid.
7
R7 TAMIL NADU FACTORIES RULES, 1950
(2) The occupier of every factory licensed under rule 4, shall submit to
the 1[Deputy Chief Inspector of Factories] having jurisdiction over the area
where the factory is situated, an application 5[in Form No.2 through online
portal of Directorate of Industrial Safety and Health], for the renewal of
the licence. The application for such renewal shall be made so as to be
received in the office of the 1[Deputy Chief Inspector of Factories], not
less than two months before the date on which the licence expires and it
shall be accompanied by the original licence if it is not already available
with the 1[Deputy Chief Inspector of Factories].
the fee for the renewal of licence for a period upto 6[ten consecutive
calendar years] instead of getting it renewed for every calendar year he
shall indicate in Form No.2, the number of years for which renewal of
licence is required.]
(5) 7[The 1[Deputy Chief Inspector of Factories] shall renew the
licence within thirty days from the date of receipt of application
referred to in sub-rule(2):]
_________________________________________________________
5Ins. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January
2018.
6Ins. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January
2018 for “five consecutive calendar years”.
Ins. by G.O. Ms. No. 105, Labour and Employment (M1), dated 25th May
2017 for “The Deputy Chief Inspector of Factories may renew the licence:”.
TAMIL NADU FACTORJBS RULES, 1950 (R. 7A
Provided that the I(Deputy Chief Inspector of J:actories] may
call for such other particulars as he may require before renewing
the licence :
Provided further that the 1[Deputy Chief Insp�ctor of Facto
ries] may renew the licence subject to such. con�1t1ons. as he may
consider necessary and which shall be specified m the licence.
(6) Suitable entry shall also be. made in the Register of
Factories regarding the renewal of the licence.
7 A. Refusal to register and grant a licence or to renew
licence in certain cases.-(1) Subject to the provisions of sub
section (3) of section 6 of the Act, the Chief Inspector may refuse
to register a factory and grant or renew a licence if he is satisfied-
(i) that an application is not accompanied by the docu
ments referred to in sub-rule (2) of rule 3 ; or
(ii) that the conditions subject to which permission was
accorded under rule 3 have not been complied with ; or
(iii) that there is imminent danger to human life in the
factory due to explosive or inflammable dust, gas or fumes and
effective measures, in his opinion, have not been taken to remove
such danger ; or
(iv) that there is imminent danger to human life due to
the building or the entrances thereto or exists therefrom being in a
dangerous or structurally unsound condition, and effective measures
in his opinion, have not been taken to remove the danger :
Z[Provided that in the case of refusal to grant or renew a
licence, the Chief Inspector shall record in writing the reasons for
such refusal and communicate the same to the occupier.]
(2) The State Government or subject to the control of the
State Government, the Chief Inspector may, by written order, how
ever, waive either in full or in part the surcharge so payable which
shall not exceed Rs. 2000 (Rupees two thousand only),
8((3) Where a Deputy Chief Inspector of Factories is of
opinion that there is prim a f 'acie case to refuse to grant or to
renew a licence for all or any of the reasons stated in sub-rule (I),
he shall forward to the Chief Inspector the app!ication for grant
or for renewal of licence received from an occupier of the factory
and the original licence granted to it to pass such orders as he
deems fit.]
�------------------------------------------'----- : 2 Subs byG.O. Ms. No 2844 Lab. &Emp, dated the 17th December, 1980.
3
Ins by G.O . . Ms No.1280, Lab. & Emp. (M·ll), dated the 17th June, 1981.
Subs. by G.O Ms No 150, Lab & Emp (l\f-lJ), dated the 14th July, 1993.
R. 9] TAMIL NADU FACTORIES RULES, 1950
1[7-AA. Revocation ��d suspension. of licence in. certain
cases. -Subject to the provisron of su�-sect1on (3) of .section 6 of
the Act, the Chieflnspector of Factories/the Joint Chteflnspector
of Factories. may, after giving the occupier of the Factory an
opportunity of m_aking �is repr.esentation,. re':oke �r suspe�d the
Jicence at any point of time during the period in which the Iicence
is in operation, if he is satisfied,-
(i) that the conditions subject to which permission was
accorded under rule 3 have not been complied with; or
t i i ) that the conditions subject to which licence was granted
under rule 4 or renewed under rule 7 have not been complied with.]
7.8. Adjustment of excess payment of Bicence fee.-Where
the amount is paid in excess of the prescribed fee for the grant of
licence or for the renewal of licence, the excess amount so paid may
be adjusted towards the fee payable for renewal of licence for the
subsequent year 2[or years]. by the 3[Deputy Chieflnspector of
Factories], on request from the occupier.
8. Transfer of liccoce.-(1) The holder of a licence or in
the event of bis death, any person carrying on the business of such
licensee may, at any time, before the expiry of the licence, apply for
permission to transfer the licence to another person or to himself.
(2) Such application for transfer shall be made to the
3[Deputy Chief Inspector of Factories} concerned and accompanied
by a fee of '[fifty rupees] for each such application.
(3) The S(Deputy Chiet'Inspector of Factories] concerned,
if he approves of the transfer, enter upon the licence under
his signature, an endorsement to the effect that the licence has
been transferred to the person named :
Provided that the 3[Deputy Chief Inspector of Factories]
concerned may call for such other particulars as he may require
before effecting the transfer :
Provided further that the 8[Deputy Chief Inspector of
Factories] concerned may effect such transfer subject to such
conditions as he may consider necessary and which shall be
specified in the licence.
(4) Suitable entry shall also be made in the Register of
Factories regarding the transfer.
9. Procedure on death or disability of Iicensee.-lf a
licensee dies or becomes insolvent, the person carrying on the
business of such licensee shall not be liable to any penalty under
1 Ins. by G 0. Ms. No.24, Lab & Emp. (M-11), dated the 12th February, 1993
2 Ins. byG 0. Ms. No.ISO, Lab & Emp (M-11), dated the 14th July, 1993.
3 Subs. by G.O. Ms No 2844 Lab. & Emp , dated the 17th December, 1980
4 Subs. byG 0. Ms No. 241, Lab. & Emp, dated the 11th September, 1991
the Act for exercising the powers granted to the licensee by the licence
during such time as may reasonably be required to allow him to make an
application for the transfer of the licence under rule 8 in his own name
for the unexpired portion of the original licence.
•
10. Loss of licence.--Where a licence granted under these
5[***]
(2) If an application for the grant or renewal of a licence is
refused,the fee paid shall be refunded to the applicant by the Chief
Inspector.
(3) If the Chief Inspector is satisfied that a factory has not worked
even on a single day during the period of licence, he may order the
refund of the licence fee collected for that period.
4[Provided that where the licence is issued or renewed for more
than one calendar year, the refund shall be made only in respect of
that calendar year in which the factory has not worked even on a single
day.]
12. Notice of occupation.--The notice of occupation shall be in
Foam No. 2.
12A. Notice of change of manager.—
Form prescribed under The notice of change of manager shall be
sub-section (1) of section 7. in Form No. 3-A.
12B. Plans and licence.-- (1) The plans approved by the
1
(2) The plans and layouts of factory buildings sent to the
1 Subs. by G.O. Ms. No. 2844, Lab.& Emp., 17-12-1980.
2 Subs. by G.O. Ms. No. 241, Lab. & Emp., 13 -9-1991
3 Subs. by G.O. Ms. No. 150, Lab. & Emp. , (M-11),14-7-1993
4 Ins. by G.O. Ms. No. 150, Lab. BSc Emp (M-11), 14-7-1993.
rules is lost or accidentally destroyed, a duplicate may be granted by
the ![Deputy Chief Inspector of Factories) having jurisdiction over the
area on payment of a fee of 2[fifty rupees].
[Chief Inspector or Deputy Chief Inspector, as the case may be] under
rule 3 and the licence granted for a factory under rule 4 shall be
readily available in the factory for inspection by the Inspectors and
additional Inspectors appointed under section 8 of the Act
1[Chief Inspector or Deputy Chief Inspector, as the case may be] for
approval under rule 3 shall be prepared by a person possessing
TAMIL NADU FACTORIES RULES, 1950 [R12B
11. Payment of fees.--3[(1) Every application relating to
grant, renewal, transfer and amendment of licence under these rules shall
be accompanied by a 4[treasury receipt or by a crossed demand
draft] of any branch of a Nationalised Bank drawn in favour of the
Deputy Chief Inspector of Factories of the region 6[or by online
payment through online portal of Directorate of Industrial Safety and
Health:]
5 Omitted by G.O. Ms. No.149, Lab & limp. (M.II), 25-7-1995
6 Ins. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January 2018.
R. 12BJ TAMIL NADU FACTORIES RULES, 1950
prescribed for the Engineering Subordinate or the Overseer class or
the Draftsman class m the College of Engineering, Guindy.
(3) After the date of the commencement of the Act, no
manufacturing process shall be carried on in any factory construc
ted extended or taken into use as a factory or part ot a factory
until a certificate of stability in respect of the buildings in the
form below has been sent by the occupier or management of the
factory to the Inspector :
Provided that the certificate of stability sent by the occupier or
management of the factory to the Inspector as required in this rule
shall be valid only for a period of three years from the date of its
issue and within thirty days after the expiry of the said period, a
fresh certificate of stability shall be sent to the Inspector.
Form of Certificate of Stability
(1) Name of the factory.
(2) Village, town and district in which the factory is situated.
(3) Full postal address of the factory.
(4) Name of the occupier of the factory.
(5) Nature of manufacturing process to be carried on in
the factory.
(6) Number of floors on which workers will be employed.
-- I certify that I have inspected the building on the .. .in which ..•
is housed and examined the various parts including the foundations
as shown in the complete plans approved by the Chief Inspector in
his letter No ... dated ... with special reference to the machinery,
plant, etc., that have been installed. I am of opinion that the
building has been constructed/extended in accordance with the
plans approved by the Chief Inspector in his Letter No ••• dated ...
that it is structurally sound and that its stability will not be
endangered by its use as a factory for the manufacture of ... for
which the machinery, plant, etc., installed are intended.
Place : (Signature)
Date : Name, designation and qualifications.
Note.-No certificate of stabilily is necessary in the case
of existing buildings for which no plans have been approved
prior to 1948.
1[(4) The certificate of stability referred to in sub-rule (3)
shall be signed by a competent person recognised by the Chief
Inspector under rule 2-A for that purpose.]
2[(5) An occupier shall not use any premises as a factory or
carry on any manufacturing process in a factory unless a licence
1 Subs b y G O M� No.J33,I�1b &Emp,d,1l�dth�21rd,\pril, 1991
2 Ins by Cl O �I� No 3R7, Lab & Lmp , dated the I 7lh !\l,t\'. l '>77
I
a diploma or degree in Engineering or pass in the examination
[R. 13A
has been issued in respect of such premises and is in force for the
time being t]
l[Provided that if a valid application for grant or renewal
of licence has been submitted and the required fee has been paid,
the premises shall be deemed to be fully licensed until such date as
the Chief Inspector grants or refuses in writing to grant �r �e�ew
the licence or the Superintending Inspector having JUrtsd1ct1on
over the a;ea where the factory is situated, renews the licence.]
2[12-C. Guidelines, instructions and records.-(!) Without
prejudice to the general responsibility ot. the occupier to comply
with the provisions of' Section'i-A, the Chief Inspector may, from
time to time issue guidelines and instructions regarding the general
duties of the occupier relating to health and safety and welfare of
all workers while they are at work in the factory.
(2) The occupier shall maintain such records, as may be
prescribed by the Chief Inspector, in respect of monitoring of
working environment in the factory.
CHAPTER II
The Inspecting Staff
8[13. Appointment of Inspectors.-(1) No person shall be
appointed as Inspector for the purposes of the Act, unless he
possesses the qualifications prescribed for such Inspectors in the
Special Rules for the Tamil Nadu Factory Service at the time of his
appointment.
(2) No person shall be appointed as Medical Inspector
unless be possesses a degree in the branch of Medicine :
Provided that preference sbalI be given in the case of appoint
ment to the post of Medical Inspector to a person who possesses
the experience in a public hospital or factory medical department
for a period of not less than two years or a diploma in Industrial
Medicine.
(3) Where for particular post specialised knowledge to deal
with special problems is required, the State Government may, in
addition to the qualifications mentioned in sub-rule (1) specify
such other qualifications for such post as they deem fit.]
4[13A.J Powers of lnspectors.-An Inspector shall, for the
. purpose of the execution of the Act, have power
be�u��d�:es
5
cer�: to do all or any of the following things, that is
tion 9. to say :-
1 Subs by CJ O Ms No 2562, L.1b & Emp. d.ued the 16th November, 19RI
2 Ins by G.O lib N.o 133, Lab, & Emp , dated the 2'lrd April, I 991.
3 Subv by Ci.O Ms No 57, Lab & Emp , d,1h:d the 27th February, 1992
4 R�1111111h�1.:dhyGO M� No 133.Lnh &Emp.d,1ti:dthi:23rdApnl.1991
TAMIL NADU FACTORIES RULES, 1950
(a) to photograph any worker, to inspect, examine, measure, co·�y,
photograph, sketch or test, as the case may be, any building or room, �PY
plant, machinery, appliance or apparatus any register or document or
anything provided for the purpose of securing the health, safety or wel-.
fare of the workers employed in a factory;
l[(aa) to seize or take copies of such registers/records or other
documents or portions thereof, as he may consider relevant in respect of
an offence under this Act, which he has reason to believe has been com
mitted by· the occupier or the manager;]
(b) in the case of an Inspector who is a duly qualified medical .
practitioner.sto carry out such medical examinations as may be necessary
for the purposes of his duties under the Act ;
(c) to prosecute., conduct or defend before a Court any complaint
or other proceeding arising under the Act or in discharge of his duties as
an Inspector :
Provided that the powers of the District Magistrates and of the Addi
tional Inspectors appointed under sub-section (5) of section 8 shall be
limited to the inspection of factories in respect of the following matters,
namely: -- · ·
Section 6 (1) (d) and (e) (Licence).
Section 9 (Powers of Inspectors).
Sections 11 to 20 (Health).
Section 23 (Employment of young persons on dangerous
machines).
Section 27 (Prohibition of employment of women and children near
cotton openers). <,
Sections 32 to 40 (Safety precautions).
Sections 42 to 48 (Welfare).
1
Ios. by S.R.O. A-930 of 1971.
R. 13A] TAMIL NADU FACTORIES RULES, 1950
TA\ilL NADU FACrORIBS RULBS, 1950 R. 14]
Sections 51 to 63 (Working hours of adults).
Section 66 (Restrictions of employment of women during
nights).
Sections 67 to 75 (Employment of young persons).
Sections 78 to 83 (Leave with wages), section 87 (dangerous
operations).
Section 91 (Power to take samples).
Section 108 (Display of notices).
Rules 102 to 108 fiamed under Section 1 1 2 .
14. Duties of Certifying Sunrgeon.- (1) For purposes of
the examination and certificarion ot young persons who wish to
. obtain certificates of fitness, the Certifying Surgeon
Rule prescri�ed shall arrange a suitable time and place for the
under sub-section d f h d I · · (4) of section 10. atten ance o. sue . �ersons, an shal give previ-
ous notice m wrtting of such arrangement to
the managers of factories situated within the local limits assigned
to him.
(2) The Certifying Sugeon shall issue his certificates in
Form No. 5. The foil and counterfoil shall be filled in and the left
thumb mark of the person in whose name the certificate is granted
shall be taken on them. On being satisfied as to the correctness of
I
the entries made therem and of the fitness of the person examined,
he shall sign the foil and initial the counterfoil and shall deliver the
foil to the person in whose name the certificate is granted. The
foil so delivered shall be the certificate of fitness granted under
section 69. All counterfoils shall be kept by the Certifying Surgeon
for a period of at least two years after the issue of the certificate.
(3) The Certifying Surgeon shall. upon request by the Chief
Inspector, carry out such examination and furnish him with such
report as he may indicate, for any factory or class or description of
factories wbere-
(a) cases of illness have occurred which it is reasonable
to believe are due to the nature of the manufacturing process carried
on, or other conditions of work prevailing therein, or
(b) by reason of any change in the manufacturing process
carried on, or in the substances used therein, or by reason of the
adoption of any new manufacturing process or of'any new substance
for use in a manufacturing process, there is likelihood of injury
to the health of workers employed in that manufacturing process, or
(c) young persons are, or are about to be, employed in
any work which is likely to cause injury to their health.
(4) For the purpose of the examination of persons employed
in processes covered by the rules relating to dangerous operations,
limits assigned to him at such intervals. as are prescribed by .tbe
rules relating to such dangerous operations.
1((5) At such visits, the Certifying Surgeon after examining
a worker shall issue a certificate of fitness in Form 27. The record '
of examination and re-examinations carried out shall be kept in
custody of the Manager of the factory. The re�ord o.f each exami
nation carried out under sub-rules ( ] ) and (2) including the nature
and the results of the tests, shall also be entered by the Certifying
Surgeon in a Health Register in Form No. 17.]
(6) If the Certifying Surgeon finds as a result of his exami
nation that any person employed in such process is no longer fit
for medical reasons to work in that process, he shall suspend such'
person from working in that process, for such time as he may think
fit and no person after suspension shall be employed in that process
without the written sanction of the Certifying Surgeon in the
Health Register. -
,,- -'(7) The manager of a factory shall afford to the Certifying
Surgeon, facilities to inspect any process in which any person is
employed or is likely to be employed. -
(8) The manager of a factory shall provide for the purpose
of any medicaLexamination which the Certifying Surgeon wishes-to
"conduct at the factory (for his exclusive use on the occasion of an
examination) a room which shall be properly cleaned and adequa
tely ventilated and I ighted and furnished with a screen, a table
(with writing materials) and chairs.
CHAPTER III
Health
2(15. Cleanliness of walls andceilings.- (I) The provision
of clause (d) of sub-section (I) of section 1 1 of the Act shall not
apply to the classes of factories or descriptions of factories or parts
thereof specified in the Schedule below :
Provided that they are kept in a clean state by washing, sweep
ing, brushing, dusting, vacuum-cleaning or other effective means :
Provided further that the said clause (d) shall continue to
apply-
(i) in respect of factories or parts of factories specified in
Part A of the schedule, to workrooms in which the amount-of cubic
space allowed for every person employed in the room is less than
500 cubic feet ; ·
1 Subs. by G.O. Ms. No. 2223, Labour and Employment, 6th_
October 1!188.
, 2 Subs. by G.O. Msr-No, 387, Labour and Employment, dated she
28th April, 1976. , ' , /"
R 15] . TAMIL NADU FACTORIES RULES, 1950
the Certifying Surgeon shall visit the factories within the local
TAMIL NADU FACTORIES RULES, 1950 IR I "
(ii) in respect of factories or parts of factories specified in
Part B of the schedule, to workrooms in which the amount of cubic
space allowed for every person employed in the room is less than
2,500 cubic feet ;
(iii) to engine houses, fitting shops, lunch rooms, canteens.
shelters, creches, cloak rooms, rest rooms, and wash places; and
(iv) to such parts of walls; sides and tops of passages and
staircases as are less than 20 feet above the floor or stair.l
(2) If it appears to the Chief Inspector that any part of a
factory, to which by virtue of sub-rule (I) any of the provisions of
the said clause (d) do not apply, is not being kept in a clean state,
he may by written notice require the occupier to whitewash or
colourwash, wash, paint or varnish the same, and in the event of
the occupier failing to comply with such requisition within two
months from the date of the notice, sub-rule ( l ) shall cease to apply
to such part of a factory, unless the Chief Inspector otherwise
determines.
1[THB SCHEDULE
(1) Blast furnaces.
(2) Brick and tile works in which unglazed bricks or tiles
are made.
(3) Cement works.
(4) Chemical works.
(5) Copper mills.
(6) Gas works.
(7) Iron and steel mills.
(8) Stone, slate and marble works.
(9) The following parts of factories:-
(a) Rooms used only for the storage of articles.
(b) Rooms in which the walls of ceilings consist ot
galvanised iron, glazed bricks, glass, slate, asbestos, bamboo thatch.
(c) Parts in which dense steam is continuously evolved
, in the process.
(d) Parts in which pitch, tar or like material is manu
factured or is used to a substantial extent, except in brush works.
The parts of a glass factory known as the glass house. Rooms in
which graphite is manufactured or is used to a substantial extent in
1.ny process.
1 Subs. by G.O. Ms. No. 387, Labour and Employment, dated the
28th April, 1976,
(e) Parts in which coal, coke, oxide of iron, ochre, lime or stone is
crushed or ground.
(t) Parts of walls, partitions, ceilings or tops of rooms which are
at least 20 feet above the floor.
(g) Ceiling or tops of rooms in print works, bleach works or dye
works, with the exception of finishing rooms or warehouses.
(h) Inside walls of oil mills below a height of 5 feet from the ground
floor level.
(i) Inside walls in tanneries below a height of 5 feet from the
ground floor level where a wet process is carried on.
Part B
(1) Coach and motor body work.
(2) Electric generating or transforming stations.
(3) Engineering works.
(4) Factories in which sugar is refined or manufactured.
(5) Foundries other than foundries in which brass casting is carried
on.
(6) Gun factories.
(7) Ship-building works.
(8) Those parts of factories where unpainted or unvarnished wood
is manufactured.]
16. Record of whitewashing, etc. - The record of dates
on which whitewashing, colour-washing, varnishing,
etc., are carried out shall be entered in a register
maintained in Form No. 7.
1(17. Disposal of trade wastes and effluents. - .In every factory,
effective arrangements shall be made for the treatment of wastes and
effluents due· to the manufacturing processes carried on therein and the
arrangements so made shall be in accordance with those approved by the
relevant authorities of Tamil Nadu Pollution Control Board appointed under
the Water (Prevention and Control of Pollution) Act, 1974 and the Air
(Prevention and Control of Pollution) Act, 1981 and the authorities of
Department of Environment.]
I Subs. by GO. Ms. No 127, Labour and Employment (M-2), dated 31-8-2005.
Register prescribed
under sub-section
(]) of section 11.
R.17] TAMILNADU FACTORIES RULES, 1950 -
R . 17AJ
17A. Ventilation and temperature-
1. Limits of temperature and air movement.-In any
factory the maximum wet bulb temperature of air in a workroom at
a height of I . 5 metres ( 5 feet) above the floor level shall not exceed I
30°C (86.F) and adequate air movement of atleast 30 metres per,
minute ( tOO feet per minute) shallbe provrded ; and in relation to
dry bulb temperature the wet bulb temperature in the workroom at
the said height shall not exceed that shown in the Schedule, or as
regards a dry bulb reading intermediate between the two dry bulb
readings that specified in relation to the higher of these two dry
'Julb readings.
THE Sc.HEOU!.8
Orv Bulb Wet Bulb
Temperature Temperature
r---.A.- -"""' ,---'-"-----..
''C (oF} •c (�F)
30 (86) 29.0 (84.2)
3l (87.8) 28.9 (84.0)
32 (89.6) 28 .8 (83.8)
33 (91.4) 28.7 (83.6)
34 (93.2) 28.6 (83.5)
35 (95) 28.5 (83.4)
36 (96.8) 28 .4 (83.2)
37 (9S.6) 28.3 (83.0)
38 (100.4) 28.2 (82.7)
39 (102 .2) 28.l (82.6)
40 (l04) 28.0 (82.5J
41 (105.8) 27.9 (82.3)
42 (107.6) 27.8 (82. l)
43 (109.4) 27.7 (81.9)
44 ( l l l . 2 ) 27.6 (81 .7)
45 ( 1 13 ) rn.s (81.5)
46 (l l4 .8) 27.4 (81.3)
47 (1 16.6) 27.3 (8 l . l )
Provided that if the temperature measured with a thermometer
inserted in a hollow globe of 15 c.m, (6 inches) dia. coated mat
black outside and kept in the environment for not less than 20
T AMJL NADU FACTORIES RULES, 1950
minutes exceeds the dry bulb temperature of air, the temperature so
recorded by the globe thermometer shall be taken in place of the
dry bulb temperature :
Provided further that when the reading of the wet bulb tempe
rature outside in the shade exceeds 27°C (80.6°F) the value of
t:be wet bulb temperature allowed in the Schedule for a given dry
bulb temperature may be correspondingly exceeded to the same
-extent:
Provided also that this requirement shall not apply in respect
pf factories covered by section 1 5 and in respect of factories where
the nature of work carried on invo lves production of excessively
high temperatures referred to in c lause (ii) of sub-section ( 1) to
which workers are exposed for short periods of time not exceeding
one hour followed by an interval of sufficient duration in thermal
environments not exceeding those otherwise laid down in this rule :
Provided also that, the Chief Inspector having due regard to
the health of the worker may in special and exceptional circum
stances, by an order in writing, exempt any factory or part of a
factory from the- foregoing requirement , in so far as restricting the
thermal conditions w i thin the lim its laid down in the Schedule are
concerned, to the extent that he may consider necessary, subject to
such conditions as he may specify. - · - -
2 . Provision of Tbermometers.-(1) If it appears to the
Inspector that in any factory, the temperature of air in a workroom
is sufficiently high and is l ikely to exceed the limits prescribed in
rule ( J ) he may serve on the manager of the factory an order requir
ing him to provide sufficient number of whirling hygrometers or
any other type of hygrometers and direct that the dry bulb and wet
bulb readings in each such ·workroom shall be recorded at such
positions as approved by the Inspector twice during each working
shift by a person espec ia l ly nominated for the purpose by the
manager and approved by the Inspector.
(2) If the Inspector has reason to believe that a substant ial
amount of heat is added inside the environment of a workroom by
radiation from walls, roof or other solid surroundings, he may
serve on the manager of the factory an order requiring him 10
provide one or more globe thermometers referred to in the first
proviso in rule ( I ) and further requ iring h im to place the globe
thermometers at places specified by h im and keep a record of the
temperatures in a suitable register.
3. Veotilation.-(1) In every factory the amount of ventila
ting openings in a workroom below the caves shall, except where
mechanical means of ventilation as required by sub-rule (2) are
provided, be of an aggregate area of not Jess than 15 per cent. of
R. 17AI TAMIL NADU FACTORIES RULES, 1950
the floor area and so located as to afford a continued supply of
fresh air :
Provided that the Chief Inspector may relax the requirements
regarding the amount of ventilating openings if be is satisfied that
having regard to the location of the factory, orientation of the
workroom, prevailing winds, roofs height and the nature of manu
facturing process carried on, sufficient-supply of fresh air into the
workroom is afforded during most part of the working time :
Provided further that these requirements shall not apply in
respect of workrooms of factories-
(i) covered by section 15 ; or
(ii) in which temperature and humidity are coritrolled by
refrigeration.
(2) Where in any factory owing to special circumstances
such a situation with respect to adjacent buildings and height of
the bu i ld ing with respect to floor space, the requirements of venti
lation openings under sub-rule ( I ) cannot be complied with or in
the opinion of the Inspector the temperature of air in a workroom
is sufficiently high and is likely to exceed the limits prescribed in
sub-rule ( I J, he may serve on the manager of the factory an order
requiring him to provide additional ventilation either by means of
roof ventilators or by mechanical means.
(3) The amount of fresh air supplied by mechanical means
of ventilation in an hour shall be equivalent to at least six times
the cubic capacity of the workroom and shall be distributed evenly
throughout the workroom without dead air pockets or undue
draughts caused by h igh inlet velocities.
(4) In regions where in summer (15 th March-15th July)
dry bulb temperatures of outside air in the shade during most part
of the day exceed 35°C (95° F) and simultaneous wet bulb tempera·
tures are 25°C (67° F) or below and in the opinion of the Inspector
the manufacturing process carried on in the workroom of a factory
perm its thermal environments with relative humidity of SO per cent.
or more, the Inspector may serve on the manager of the factory an
order to have sufficient supply of outside air for ventilation cooled
by passing it through water sprays either by means of unit type of
evaporative air coollers (desert coollers), or, where supply of outside
air is provided by mechanical means through ducts in a plenum
system, by means of central air washing plants.
18. When artificial humidification not
allowed .-There shall be no artificial humidifica
tion in any room of a cotton spinning or weaving
factory-
Rules 18 to 28
prescribed under
sub-section (1) of
section 15.
· TAMIL NADU FACTORIES RULES, 1950 [R 18
R. 181 TAMIL NADU F
(a) by the use of steam during any period when the dry
bulb temperature of that room exceeds {8511F or 29.Soqa ;
(b) at any time when the wet bulb reading of the hygro
meter is higher than that specified in the following schedule in
relation to the dry bulb reading of the hygrometer at the time ; or
as regards a dry bulb reading intermediate between any two dry
bulb readings indicated consecutively in the schedule, when the wet.
bulb reading is higher than that specified in relation to the higher
of these two dry bulb readings:-
l(THB saumuu
ep
60.0
'1.0
62.0
63.0
ti4.0
65.0
66.0
67.0
68.0
69.0
7-0JJ
1Ull
m»
73.0
74.0
75.0
76.0
77.0
'18.0
79.0
80.0
31.0
S2.0
83.0
84.0
oc
15.S
16.0
165
17.0
I8.0
ras
19.0I
19.5
20,C,
20.5
21.0
215
22.0
23.0
23.Si
24.0
24.S
25.0,
25.S
26.0
26.S
27.0
23.0
28.S
29.0
•p
58.0
59.0
60.0
61.0
62.0
ss.o
64.0
65.0
66.0
67.0
68.0
69.0
70.0
71.0
'i2.0
73.0
74.0
75.0
76.0
77.0
78.0
79.0
80.0
80.S
81.0
oc
14.5
15.0
15.5
16.0
17.0
17.5
18.0
18.S
19.0
19.5
20.0
20.S
21.0
22.0
22.S
23.0
23.S
24.0
24.S
25.0
25.S
26.0
27.0
27.0
21.S
Wet bulb
,--.>..-�
i Sub,. by G.O. Ms. No. 367.,Labo&r and Employment. dated the 28th
April. 1f76.
AClORlf:!S RU.LBS, 19.50
TAIWIL NADU F ACIO!l.lES RutBS, !950 ll. H 8]
Dry
,--.A---.
op oc
85.0 29.S
86.0 30.0
s7.o so.s
88.0 31.0
89.0 31.S
90.0 32.0
91.0 33.0
92.0 33.5
93.0 34.0
94.0 34.S
95.0 35.0
96.0 35.5
97.0 36.0
98.0 37.0
99.0 37.5
100.0 38.0
101.0 38.S
102.0 39.0
)03.0 39.5
104.0 40.0
105.0 40.S
106.0 41.0
107.0 41.5
108.0 42.0
109.0 43.0
110.0 43.S
Wet Bulb
,- A-- �
op CIC
'82.0 28.0
'82.S 28.6
�3.0 28.5
83.S 28..5
'84.0 29.0
'84.S 29.0
.'85.0 29.S
�5.5 30.0
'86.0 30.6
'86.0 30.0
'87.0 30.5
'81.S 31.0
'88.0 31.0
'.88.S 31.5
�9.0 32.0
�9 .. S 32.0
90.0 32.5
'90.0 32.S
90.5 32.S
'90.5 32.5
'91 .. 0 33.0
'91.0 33.G
91.6 33.0
91.5 33.0
92.0 33.5
92.0 33.SJ
Provided, however, that clause (b) shall not apply when the
difference between the wet bulb temperature as indicated by the
hygrometer in the department concerned and the wet bulb tempera
tore taken with a hygrometer outside i11 the shade is less than
1(35°F or 2°C]:
Provided further that when the reading of the wet bulb tempe
rature outside in the shade exceeds [80° F or 27°C]1, the value of"
the wet bulb temperature allowed in the schedule for a given dry
bulb temperature may be correspondingly exceeded to the same
extent.
1 Subs. by G.O. Me. No. 387, labour and Employment. dated the 28tli
April, 1976.
19. Provision of hygrometer.-Io all departments of cotton
spinning and weaving mills wherein artificial humidification is
adopted, hygrometers shall be provided and maintained in such
positions as are approved by th� Inspector. !'h� number of hygro
meters shall be regulated according to the following scale :-
(a) Weaving Department s--Cnu: hygrometer for departments
with less than SOO looms, and one additional hygrometer for every
500 or part of 500 looms in excess of 500.
(b) Other Departments.-Ooe hygrometer for each room of
less than 8 495 cubic metres capacity aod one extra hygrometer for
each 5,663'.4 cubic metres or part thereof, in excess of this.
(c) One additional hygrometer shall be provided and main
tained outside each cotton spinn ing and weaving factory wherein
artificial humidification is adopted and in a position approved by
the Inspector, for taking hygrometer shade readings.
20. Exemption from maintenance of bygrometers.-When
the Inspector is satisfied that the limits of humidity a l lowed by the
schedule to rule 18 are never exceeded, he may, for any department
other than the weaving department, grant exemption from the
maintenance of the hygrometer. The Inspector shall record such
exemption in writing. ·
21 . Copy of schedule to rule 18 to be affixed near every
hygrometer.-A legible copy of the schedule to rule 18 shall be
affixed near each hygrometer.
22. Temperature to be recorded at each hygrometer -At
each hygrometer ma intained in accordance w i th rule l 9, correct wet
and dry bulb temperatures shal l be recorded thrice dai ly _dur ing
each working day by competent persons nomina ted by the manager
and approved by the Inspector. The temperature sha l l be taken
between 7 a .m. and 9 a .m . , between 1 1 a.rn. and 2 p.m . (but not in
the rest interval) and between 4 p.m . and 5.30 p .m . In exceptional
circumstances, such addi t iona l readings and between such hours, as
the Inspector may specify, sha l l be taken. The temperatures shal l
be entered in a Humidity Register in the prescribed Form No. 6, '
maintained in the factory. At the- end of each month , the persons
who have taken the readings shall sign the register and certify the
correctness of the entries. The register shall always be available
for inspection by the Inspector. ·
23. Specifications of hygrometer.-(!) Each hygrometer
shall comprise two mercurial thermometers of wet bulb and dry
bulb of similar construction, and equal in dimensions, scale and
divisions of scale. They shall be mounted on a frame with a suita-
. ble reservoir containing water.
[R. 23 TAMIL NAOU FACTORIES Rutzs, t9SO
(2) The wet bulb shall be closely covered with a single layer of
muslin, kept by means of a wick attached to it and dropping into the water
in the reservoir. The muslin covering and the wick shall be suitable for the
purpose, clean and free from size or grease. ·
(3) No part of the wet bulb shall be within 7.6 centimetres from the
dry bulb or less than 2.5 centimetres from the surface of the water in the
reservoir and the water reservoir shall be below it, or the side of it away
from the dry bulb.
(4) The bulb shall be spherical and of suitable dimensions and shall
be freely exposed on all sides to the air of the room.
(5) The bores of the stems shall be such that the position of the
top of the mercury column shall be readily distinguishable at a distance of
61 centimetres.
(6) Each thermometer shall be graduated so that accurate readings
may be taken between 1[10 and 48.9 degrees].
(7) Every degree from 1[10 degree upto 48.9 degrees] shall be clearly
marked by horizontal lines on the stem each fifth and tenth degree shall be
marked by longer marks than the intermediate degrees and the temperature
marked opposite each tenth degree, i.e., 1[10, 15.6, 21. 1 , 26.7, 32.2, 37.8, 43.3
and 48.9].
(8) The markings as above shall be accurate, that is to say, at no
temperature between 1(10 and 48.9 degrees] shall the indicated readings be
in error by more than two-tenths of a degree.
(9) A distinctive number shall be indelibly marked upon the
thermometer.
(10) The accuracy of each thermometer shall be certified by the Nati
onal Physical Laboratory, London, or some competent authority appointed
by the Chief Inspector and such certificate shall be · attached to the
Humidity Register.
24. Thermometers to be maintained in efficient order. - Each ther
mometer shall be maintained at all times during the period of employment in
efficient working order so as to give accurate indications and in particular-
(a) the wick and the muslin covering of the wet bulb shall be
renewed once a week ;
(b) the reservoir shall be filled with water which shall be completely
renewed once a day. The Chief Inspector may direct the use of distilled water
or pure rain water in any particular mill or mills in certain localities ;
( c) no water shall be applied directly to the wick or covering during
the period of employment.
I Subs. by GO. Ms. No. 127, Labour and Employment (M-2) dated the 31-8-2005.
TAMILNADU FACTORIES RULES, 1950 R 24]
(R. 29 TAMIL NADU FACTORlEC, RULES, 1950 l
25. An inaccurate thermometer not to be used without
fresh certificate · · - 1 1 an Inspector gives notice in writing that a
thermometer i� not accurate, it sha II not, after one month from the
date of such notice, be deemed to be accurate unle-s and unti l it has
been re-examined a, prescribed and a fresh certificate obtained
which certificate shall be kept attached to the Humidity Register.
26. Hygrometer not to be affixed to wail, etc • . unless
protected by wood.-( I ) No hygrometer shall be affixed to a wall
piliar, or other surface unless protected th_er_efrom by wo?d or other
non-conducting mater ial at least 12 .7 mill imetres in thickness and
distant atleast 2.5 centimetres from the bu lb of each thermometer.
(2) No hygrometer sha l l be fixed at a height of more than
J . 7 metres from the floor to the top of thermometer stem or in the
direct draughts from a fan, window, or venti lating opening.
27. No reading to be taken within 15 minutes of renewal
of water.-No reading shall be taken for record on any hygro
meter within 15 minutes of the renewal of water in the reservoir.
28. How to introduce stem for humidification.-ln any
room in which stem pipe, are used for the introduction of steam
for the purpose of artificial humidification of the air; the following
provisions shall apply-
(a) The diameter of such pipe shall not exceed 5 1 centi
metres and in the case of pipes are installed after 1st day of April,
1949, the diameter shall not exceed 2 .S centimetres.
(b) Such pipes shaJI be as short as is reasonably practicable.
(c) All hangers supporting such pipes shall be separated
from the bare pipes by an efficient insulator not less than 12.7
millimetres in thickness.
(d) No unrecovered jet from such pipe shall project more
than 1 J .5 centimetres beyond the outer surface of any cover.
(e) The steam pressure shall be as low as practicable and
shall not exceed 3 1 . 8 kg. per square centimetre.
(f) The pipe employed for the introduction of steam into
the air in a departrnentshall be effectively covered with such non
conducting material, as may be approved by the Inspector in order
to m inimise the amount of heat radiated by them into the depart
ment.
29. Liibting-Applieation and commencement - ( I )
Subject as in these rules provided, rules 29 to 33
shall apply to factories in which persons are being
regularly employed in a manufacturing process or
processes for more than 4lS hours a week, or in
shifts, provided that nothing in these rules shall be
'Rules 29 to 33
r rescrtbed under
sub-section (4)
c.hection 17.
TAMIL NADU FACTORIES RULES, 1950 · .. ft. 31 )
deemed to require the provision of lighting of a s�ecified s_ta!"dard
in any building or structure so constructed that, ID the oprmon of
the Chief Inspector, it would not be reasonably practicable to
comply with such requirement.
(2) Rules 29 to 33 shall come into force, in respect of any
class or description of factories, on such dates as the State Govern
ment may, by notification in the Official Gazette, appoint in this
behalf. ·
30 Llghtfng of interior parts.-(1) The general illumina
tion over those interior parts of a factory where persons are regu
larly employed shall be not Jess than 1(65 lux] measured in the hori
zontal plane at a level of 9 1 .4 centimetres above the floor:
Provided that in any such parts in which the mounting height
of the light source for general il luminat ion necessarily exceeds
7.6 metres measured from the floor or where the structure of the
room or the position or construction of the fixed machinery or
plant prevents the uniform attainment of this standard, the general
illumination at the said level shall be not less than 1(22 Jux} and
where work is actually being done the illumination shall be not
less than 'L 65 lux].
(2) The illumination over all other interior parts of the
factory over which persons employed pass shall . when and where
a person is passing, be not less than 1 [5 .5 lux] at floor level.
(3) The standard specified in this rule shall be without
prejudice to the provision of any additional il lum inat ion required
to render the lighting sufficient and suitable for the nature of the
work.
31. Prevention of glare .-(1) Where any source of artific ia l
light in the factory is less than 4. 9 metres above floor level, no part
of the light source or of the l ight ing fitting having a brightness
greater than I 5 candles per square centimetres shall be vis ib le to
persons whi l s t norma l ly employed within 30.5 metres of the source
except where the angle of elevation from the eye to the source or
part of the fitting as the case may be exceeds 20°.
(2) Any local light, that is to say, an artificial light designed
to illuminate particularly the area or part of the area of work of a
single operative or small group of operatives working near each
other, shall be provided with a suitable shade of opaque material
to prevent glare or with other effective means by which the light
source is completely screened from the eyes of every person emplo
yed at a normal working place, or shall be so placed that no such
p_ersoa is exposed to glare therefrom.
1 Subs. by G.O. Ms. No. 359, Labour and Employment, dated the 2nd
... r, 1978.
32. Power of Chief Inspector to exempt.-Where the Chief
Inspector is sansfied in respect of any particular factory or part
thereof or in respect of any description of workroom or process that
any requirement of rules 29 to 31 is inappropriate or is not reason
ably practicable, he may, by order in writing, exempt the factory
or part thereof, or description of workroom or process from such
requirement to such extent and subject to such conditions as he
may specify.
33. Exemption from rule 30.-,-(l) Nothing in rule 30 shall
apply to the parts of factories specified in Part I of · the Schedule
annexed hereto.
(2) Nothing in sub-rule ( I ) of rule 30 shall apply to the
factories or parts of factories respectively specified in Part 11 of the
said Schedule.
SCHEDULE
Part I
Parts of factories in which light sensitive photographic
materials are made or used in an exposed condition.
Part II
Cement works.
Works for the crushing and grinding of limestone.
Gas works.
Coke oven works.
Electrical stations.
Flour mills.
Malting and breweries.
Parts of factories in which the following processes are carried on.
Concrete or artificial stone-making.
Conversion of iron into steel.
Smelting of iron ore.
Iron or steel rolling.
Hot rolling or forging, tempering or annealing of metals. ·
Glass blowing and other working in molten glass.
Tar distiIIing.
Petroleum refining and blending.
34. Quantity of drinking w�ter.-The quantity of drinking
Rules 34 to 39 water to be provided for the .workers in every
prescribed under factory shall be at. le�st 4.5 litres per day per
aub-sei:tion (4) wo�ker and sue� drmkm; water �hall be readily
or stc11on 18. available at all times during working hours.
TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 R. 39]
35. Source of supply .-The water provided for drinking
shall be supplied-
(a) from a public water-supply system, or
(b) from any other source approved in writing by the
Health Officer.
36. Means of supply.-lf drinking water is not supplied
directly from taps either connected with public water-supply
system or any other water-supply system of the factory approved
by the Health Officer, it shall be kept in suitable vessels, receptacles
or tanks fitted with taps, and having dust proof covers placed on
raised stands or platform, in shade and having suitable arrange
ments of drainage to carry away spilt water. Such vessels or
receptacles and tanks shall be kept clean and the water renewed at
least once every day. A l l practicable measures shall be taken to
ensure that the water is free from contamination.
�7. Cleanliness of well or reservoir -(1) Drinking water
shall not be supplied from any open well or reservoir unless it is co
constructed, situated, protected and maintained as to be free from
the possibility of pollution by chemical.er bacterial and extraneous
impurities.
(2) Where drinking water is supplied from such well or
reservoir the water in it shall be sterilized once a week or more
frequently if the Inspector, by written order, so requires, and the
date on which sterilizing is carried out shall be recorded :
Provided that this requirement shall not apply to any such
well or reservoir if the water therein is filtered and treated to
the satisfaction of the Health Officer before it is supplied for
consumption.
38. Report from Health Officer .-The Inspector may, by
order in writing, direct the Manager to obtain, at such time orat
such intervals as he may direct, a report from the Health Officer as
to the fitness for human consumption of the water supplied to the
workers, and in every case to submit to the Inspector a copy of such
report as soon as it is received from the Health Officer.
39. Cooling of water.-In every factory wherein more than .
two hundred and fifty workers are ordinarily employed-
{a) the drinking water supplied to the workers shall, during
.hot weather, be cooled by ice or other effective method : .
Provided that, if ice is placed in the drinking water, the ice
shall be clean and wholesome and shall be obtained only from a
source approved in writing by the Health Officer ; .·
(b) the cooled drinking water shall be supplied in every can
teen, lunch-room an4 rest-room and also at conveniently accessible points
throughout the factory which for the purpose of these rules shall be called
"Water Centres" ;
(c) the water centres shall be sheltered from the weather and
adequately drained ;
(d) the number of water centres to be provided shall be one
"centre" for every 150 persons employed at any one time in the factory : ,
· Provided that in the case of a factory where the number of persons
employed exceeds 500, it shall be sufficient if there is one such "centre"
as aforesaid for every 150 persons upto the first 500 and one for every 500
persons thereaftea;
1 [Provided further that the distance between the place of work of any
worker shall not be more than fifty metres from the nearest water centre or
'any distance as may be specified by the Inspector.]
(e) every water centre shall be maintained in a clean and orderly
condition;
(t) every water centre shall be incharge of a suitable person who shall
distribute the water. Such person shall be provided with clean clothes while
on duty:
Provided that, the Chief Inspector may exempt any ''water centre"
from the requirements of this 'clause.
Clause (t) shall not apply to any factory in which suitable mechani
cally operated drinking water :,efrigerating units are 'installed to the satis
faction of the Chief Inspector.
40. Latrine Accommodation. -- Latrine accommodation shall be
Rules 40 to 49 prescribed provided in every factory on the following scale :
under sub-section (3) of
Section 19. (a) Where women are employed, there shall
be at least one latrine seat for e.very 20 women ;
I Added by G.O. Ms. No. 2223, Labour and Employment, dated the 6th October, 1988.
[R.40 T:AMIL NADU FACTORIES RULES 1950
-,
[R.44
under cover and every
seat in the latrine shall be so partitioned_ off as to secure privacy and each
partition shall have a proper door and fastenings.
I
43. Signboards to bedisplayed. -- Where workers of both sexes are
employed there shall be displayed outside each latrine block a notice in.the
language understood by the majority of the workers "For Men only" fJf
"For Women only", as the case may be. The notice shall also bear the
figure of "a man" or of "a woman", as the case may be.
44. Urinal accommodation. -- (1) Urinal accommodation shall be
provided for the use of workers and shall not be less than 61 centimetres in
length for every 50 workers : provided that, where the number of workers
employecf exceeds 500, it shall be sufficient if there is one urinal for every
50 workers upto the first 500 employed and one for every 100 thereafter.
Where women are employed, separate urinal accommodation shall be
provided for them on the same scale as mentioned above :
Provided further that the Chief Inspector of Factories may by order in
writing exempt, subject to such conditions as he may think fit to impose,
small factories employing less than 20 workers from the provision of
separate urinal accommodation if he is satisfied that the latrine accommo
dation in such factories is sufficient and suitable.
f�) In calculating the urinal accommodation required under sub-rule
(1 ), any odd number of workers Jess than 50 or 100, as the case may be. shall
TAMIL NADUFACTORIES RUI.ES 1950
(b) Where males are employed, there shall be at least one latrine seat for
every 20 males : Provided that, where the number of males employed
ex:ceeds 100, it shall be sufficient if there is one latrine seat for every 20
males upto the first 100, and one for every 50 thereafter.
_ In calculating the number of seats required under this rule, any
odd number of workers less than 20 or 50, as the case may be, shall
be reckoned as 20 or 50 and the maximum number of persons working in
pie factory at any time and not the total number of persons employed
in the factory, shall be taken into account,
41. Latrmes to conform to public health requirements, -- Latrines
other than those connected with an efficient water-borne sewage system,
shall comply with the requirements of the Public Health authorities.
42. Privacy of'latrfnes, -- Every latrineshall be
TAMIL NADU FACTORIES RULF.S · 1950
reckoned as 50 or 100, and the maximum numberof persons working in
the factory, at any time and not the total number of persons employed in the
factory, shall be taken into account
45. Urinals to conform to public health requirements. -- Urinals
other than those connected with an efficient water borne sewage system,
and urinals in a factory wherein more than two hundred and fifty workers
are ordinarily employed shall comply with the requirements of the Public
Health authorities. .
46. Certain latrines and urinals to be connected to sewage system.-
When any general system of underground sewerage with an assured wat�r
supply for any particular locality is provided in a municipality all latrines
and urinals other than septic tank latrines and any other type of latrines and
urinals to be approved for this purpose by the Public Health authority, of a
factory situated in such locality shall, if the factory is situated within 30.5
metres of an existing sewer, be connected with that sewage system.
47. Whitewashing and colourwashing of latrines and urmals. -
The walls, ceilings and partitions of every latrine and urinal shall be white
washed or colourwashed and the whitewashing or colourwashing shall be
repeated at least once in every period of four months. The dates on which
the whitewashing or colourwashing is carried out shall be entered in the
prescribed register (Form No. 7) :
Provided that this. rule shall not apply to latrines and urinals, the walls,
ceiling, or partitions of which are laid in glazed tiles or otherwise finished
to provide a smooth polished impervious surface and that they are washed
with suitable detergents and disinfectants at least once in every period of
four months:
48. Construction and maintenance of drains. -- All drains carrying
waste or sullage water shall be constructed in masonry or other imperme
able materials and shall be regularly flushed and effluent disposed off by
connecting such drains with a suitable drainage line : ·
Provided that, where there is no such drainage line, the effluent shall
be deodorized and rendered innocuous and then disposed off in suitable
manner to the satisfaction of the Health Officer.
be
49. Water taps in latrines. -- Where piped water-supply is available
a sufficient numberof water taps, conveniently accessible shall be provided
in or near such latrine accommodation. Where there is no continuous supply
of water, watercistemswith cans should be provided for washing purposes.
Rules SO to 52 'prescribed
&tder .sub-section (2) of
section 20.
50. Number and location or spittoons. -
The number and location of the spittoons to be
provided shall be to the satisfaction of the In
spector.
51. Type of spittoons. -- The spittoons shall be of either of the
following types : --
(a) A galvanized iron container with a conical funnel-shaped
cover. A layer of suitable disinfectant liquid-shall always be maintained in
the container, or ·
(b) a container filled with dry, clean sand anp covered with a
layer of bleaching powder, or ·
(c) any other type approved by the Chief Inspector.
52. Cleaning or spittoons. -- The spittoons mentioned in clause (a) of
rule ·51 shall be emptied, cleaned and disinfected at least once every day
and the spittoon mentioned in clause (b) of rule 51 shall be cleaned by
scrapping out the top layer of sand as often as necessary or at least once .
every day.
1[52-A. Planting of trees.>- The occupier of every factory employing
one hundred or more workers shall plant and maintain trees within the.
premises of the factory. The number, type and layout of trees shall be
approved by the District Agricultural Officer concerned :
Provided that if it is not possible to plant trees due to non-availability
of space in any factory or class of factories, the District Agricultural Officer
may recommend to the Government for grant of exemption to such factory
or class of factories from the provisions of this rule.]
I Ins. by G.O.Ms. No. 1569, Labour, dated the 1st August, 1985.
, TAMIL NADU FACTORIES RULES 1950 52A]
fR.53 TAMIL NADU FACTORIES RUI..ES 1950
CHAPTER IV
Safety
SJ. Further safety precautions. - (1) With
out prejudice to the provisions of sub-section (1)
of section 21 in regard to the fencing of ma
chines, the further precautions specified in the schedules annexed hereto
shall apply to the machines noted in each schedule.
(2) This rule shall come into force, in respect of any class or descrip
tion of factories, where machines noted in the said schedules are in use, on
such dates as the State Government may, by notification in the Official
Gazette, appoint in this behalf.
Registe� prescribed 1[(3) Register prescribed under section
under sub-section '(I) of sec- •
tion 22 (1). 22 (1) .-- Register to record the names of
specially trained adult workers shall be in Form
No. 35 and this register shall be made available for inspection at all
times and produced on demand during working hours or when any work
is being carried on in the factory.]
2[SCHEDULE I
Textile Machinery except Machinery used in Jute Mills
1. Application. -- The requirements of this schedule shall apply to
machinery in factories engaged in the manufacture or processing of textiles
other than jute textiles. The schedule would not apply to machinery in
factories engaged exclusively in the manufacture of synthetic fibres.
2. Defmitions. --For the purposes of this schedule --
(a) ''Calendar'' means a set ofheavyrollers mounted on vertical side
frames and arranged to pass cloth between them. Calendars may have two
to ten rollers, or bowls, some of which can be heated.
1 Subs. by G.O. Ms. No. 1250, Labour and Employment, 26th June, 1989.
Further precautions
prescribed under sub-section
(2) of section 21.
more rolls, one of which is engraved for producing figure effects
of various kinds on a fabric.
(c) "card" mea,ns. a machine consisting of cylinders. of
various sizes aud in certain cases flats covered with card. clothing
and set in relation to each other so that fibres m staple torm may
be separated into individual relationship. The speed of the
cylinders and their direction of rotation varied. The finished pro·
duct is delivered as a silver. Cards of different types are : the
revolving flat card, the roller and clearer card, etc.
(d) "card clothing" means the material with which the
surfaces of the cylinder, deffer, flats, etc • of a card are covered and
consists of a.thick foundation material made of, either textile fabrics
through which are pressed many fine closely spaced specially bent
wires, or mounted saw toothed wire . .
(e) "Comber" means a machine for combing fibres of
cotton, wool, etc. The essential parts are device for freeding for
.ward a fringe of fibres at. regular intervals and an arrangement of
combs or pins, which , at the right time pass through the fringe.
All tangled fibres, shore fibres, and nibs are removed and the loog
fibres are laid para I lei.
(f} "comb ined machinery" means a general classification
of machinery including combers sliver lab machines, ribbon Jab
machines and gill boxes, but excluding cards.
(g) " Rotary staple cutter'' means a machine consisting
of one or more rotary blades used for the purpose of cutting textile
fibres into staple lengths.
(h) "Garnett machine " means any ofa number of types
of machines for opening hard twisted waste of woll, cotton, silk,
etc Essentially, such machines consist of a licker-in; one· or more
cylinders, each having a complement worker and stripper rol ls;
and a fancy roll and deffer. The action of such machines is some
what like that of a woo Icard, but it is much more severe in that
the various rolls are covered with garnett wire instead of clothing.
(i) "G i l l box" means a machine used in the worsted
system of manufacturing yarns. Its function is to arrange fibres
in paraJlel order. Essentially, " it consists of a pair of feed rolls
and a series.of followers where the followers move at a faster sur
face speed and perform a combing action.
(j) . " In-running rolls" means any pair of rolls or drums
between which there is a " nip ".
(k) " Interlocking arrangement " means a device that
prevents the setting in motion of a dangerous part of a machine
TAMIL NADU FACfORIES RUU!S, 1950 [R.53
(b) "Embossing calender" means a calender with ! W I) or
R53] TAMIL NADU FACTORIES RULES, 1950
or the machine itself while the guard cover or door provided to
safeguard against danger is open or unlocked, and which will also
hold the guard cover or door closed and locked while the machine
or the dangerous part is in motion.
(I) •• Kier" means a large metal vat, usually a pressure
type, in which fabrics may be boiled out, bleached, etc.
(m) " Ribbon lap per" means a machine or a part of a
machine used to prepare laps for feeding a cotton comb; its pur
pose is to provide a uniform lap m which the fibres have been
straightened as much as possible.
(n) "Si lver lapper" means a machine or a part of a
machine m which a number of paralle l card covers are drafted·
slightly, laid side by side in a compact sheet and wound into a
cylindrical package.
(o) "Loom'' means a machine for effecting. the inter
locking of two series of yarns crossing one another at-right angles.
The warp yarns are wound on a warp beam and pass through
beadles and reeds. The fill ing it shot across in a shuttle and
settled in place by reeds and slay, and the fabric rs wound on a
cloth beam.
(p) " Starch mangle " means a mangle that is used specifi
cally for starching cotton goods . It commonly consists 'of two
large rolls and a shallow open vat with several immersion rolls.
The vat contains the starch solution.
(q) "Water mang le" means a calender having two or
more rolls used for squeezing water from fabrics before drying.
Water mangles also may be used in other ways during the finishing
of various fabrics
(r) • •Mu le" means. a type of spinning frame having a
bead stock and a carriage as its two main sections. The head
stock is stationary. • The-castiage is movable and it carries the
spindles which draft. and spin the rovine into yarn. The carriage
extends over the Whole width · of the machine and moves slowly
towards and sway from the head stock during the • spinning
operation.
(s) " Nip " is the danger zone between two rolls or drums
which by virtue of their positioning and movement create a
nipping hazard.
(t) " Openers and pickers " means a general classification
of machinery which includes breaker pickers, intermediate pickers,
finisher pickers, single process pickers, multiple process pickers,
willow machines, card and picker waste cleaners, thread extractors,
shredding machines, roving waste openers, shoddy pickers, bale
TAMIL NADU FACTORIES RULES, 1950
breakers, feeders, vertical openers, lattice cleaners, horizontal
cleaners and any similar machinery equipped with either cylinders,
screen section, calender section, rolls, or beaters used for the
preparation of stock for further processing.
(u) "Paddler" means a trough for a solution and two or
more squeeze rolls between which cloth passes after being passed
through a mordant or dye bath.
(vl " Plaiting machise " means machine used. to Jay cloth
into flods or regular length for convenience or subsequent prucess
or use.
(w) "Rol ler printing machine" means a machine consis
ting of a large central cyl inder or pressure bowl, around the lower
part of the perimeter of which is placed a series of engraved -color
rollers (each having a color through), a furnisher roller, doctor
blades, etc. The machine is used for printing fabrics.
(x) ·• Continuous bleaching range" means a machine for
· bleaching of cloth in rope or open- width form with the following
arrangement. The cloth after wettmg out pass through a squeeze
roll into a saturator containing solution of caustic soda and then to an
enclosed J-Box. A V-shaped arrangement is attached to the front
part of the JvBox for uniform and rapid saturation of the cloth
with steam before it i� packed down in the J-Box. The cloth, in
a single strand rope form passes over a guide roll down the first
arm of the ' V ' and up the second Steam is injected into the ' V '
at the upper end of the second arm so that the cloth is rapidly
saturated with steam at this point The J-Box capacity is such
that cloth will remain hot for a sufficient time to complete the
scouring action. It then passes a serres of washers with a squeeze
roll in-between. The cJoth then passes through a second set of
saturator, J-Box, and washer, where it is treated with the peroxide
solution . By slight modification of the form of the unit, the same
process can be applied to open-width cloth.
(y) "Mercerizing range" means a 3-bowl mangle, a tentee
frame, and a number or boxes for washing and scourging. The
whole set up is in a straight line and all parts operate continuously.
The combination is used to saturate the cloth with sodium
hydroxide, stretch it while saturated, and washing out most of the
caustic before releasing tension.
(z) " Sanforizing machine " means a machine consisting of
a large steam-heated cylinder, and endless, thick, woollen felt
blanket which is in close contact with the cylinder for most of its
perimeter, and an electrically heated shoe which presses the cloth
against the blanket while the latter is in a stretched condition as it
curves around feed-in roJI.
R53] TAMIL NADU FACTORIES RULES, 1950
ing cloth. Cutting action is provided by a number. of steel blades
spirally mounted on a roller. The roller rotates m close contact
with a fixed ledger blade. There may be from one to six such
rollers on a machine.
(bb) " Singeing machine " means a machine which com
prises of a heated roller, plate, or an open gas flame. The cloth or
yarn is rapidly passed over the rol�er or the plat_e or through the
open gas flame to remove fuzz or hairness by burning.
(cc) "Slasher" means a machine used for applying a size
mixure to warp yarns. Essentially, it consists of a stand for hold
ing section beams, a size box, one or more cylindrical dryers. or an
enclosed hot air dryer, and a beaming end for winding the yarn on
the ]oom beams.
(dd) "Tenter frame" means a roaching for drying cloth
under tension. It essentially consists ofa pair of endless travelling
chains .fitted with clips of fine pins and carried on tracks. The
cloth is firmly held at the selvages by the two chains which diverge
, as they move forward so that the cloth is brought to the desired
I Width.
(ee) "Warper" means a machine for preparing and arrang
ing the yarns intended for the warp of a fabric specifically a beam
warper.
3. General safety requirements.-(!) Every textile
machine shall be provided with individual mechanical or electrical
means for starting and stopping such machines. Belt shifter on
machines driven by belts and shifting should be provided with a
belt shifter lock or an equivalent positive locking device.
(2l Stopping and starting handles or other controls shall
be of such design and so positioned as to prevent the operator's
. hand or fingers from striking against any moving part or any other
I part of the machine.
1 (3) All belts, pulleys, gears, chains, sprocket wheels, and
i other dangerous moving parts of machinery which either form part
. of the machinery or are used in association with it, shall be
; securely guarded.
4. Openers and pickers -(1) In all opening or picker
machinery, beaters and other dangerous parts shall be securely
'fenced by suitable guards so as to prevent contact with them. Such
guards and doors or covers of openings giving access to an'y
. dangerous part of the machinery shall be provided with interlocking
, arrangement :
(aa) "Shearing machine" means a machine used for shear
TAMIL NADU FACTORIBS RULE!',, 1950· [R. 53
Provided that in the case of doors or covers of openings giving
access to any dangerous pan other than beater covers, instead of
the interlocking arrangement, such openings may be so fenced by
guards which prev�n.t access to an� such dangerous part �nd which
is either kept positively locked in posruon or fixed in such a
manner that it cannot be removed without the use of hand tools.
(2) The feed rolls on all opening and picking machinery
shall be covered with a guard disigned to prevent the operator from
reaching the nip while the machinery is in operation.
(3) The lap forming rollers shall be fitted with a guard or
cover which shall prevent access to the nip at the intake of the
lap roller and fluted roller as long as the weighted rack is down.
The guard or cover sha l l be so locked that it cannot be raised unt il
the machine is stopped, and the machine cannot be started unt il
the cover or guard is closed :
Provided that the foregoing provision shall not apply to the
machines equipped with automatic lap forming devices:
Provided further that any such machine equipped with an
automatic lap forming device shall not be used unless the automatic
lap forming device is in efficient working order.
5. Cotton cards.-(1) All cylinder doors shall be secured
by an interlocking arrangement which shall prevent the door being
opened until the cylinder has ceased to revolve and shall render it
impossible to restart the machine until the door has been closed :
Provided that the latter requirement in respect of the auto
matic locking device shall not apply while stripping or grinding
operations are carried o u t :
Provided further that stripping or grinding operations shall be
carried out only by specially trained adult workers wearing tight
fitting clothing whose names have been recorded in the register
prescribed in this behalf as required in sub-section (1) of section 22.
(2) The licker-in shall be guarded so as to prevent access
to the dangerous parts.
(3) Every card shall be equipped with an arrangement
that would enable the card cylinder to be driven by power during
stripping/grinding operations without having to either shift the
main belt to the fast pulleys of the machine or to dismantle the
interlocking mechanism. Such an arrangement shall be used only
for stripping or grinding operations.
6. Garnett macb ines. -(t) Garnett licker-ins shall be
enclosed.
shall be installed in a way that keeps worker rolls reasonably
accessible for removal or adjustment.
(3) The underside of the garnett shall be guarded by a
screen mesh or other form of enclosures to prevent access.
7. Giilil boxes.-(1) The feed end shall be guarded so as to
prevent fingers being caught in the pins of the intersecting fallers.
(2) All nips of in-running rolls shall be guarded by
suitable nip guards conforming to the following specifications :
Any opening which the guard may permit when fitted in
position shall be so restricted with respect to the distance of the
opening from any nip point through that opening and in any
circumstances, the maximum width of the opening shall not
exceed the following : ·-
Distance of opening Maximum width
from nip point. of opening.
O t o 38 mm 6 m m
39 to 63 mm lOmm
64 to 88 mm 13 mm
89 to 140 mm 15mm
141 to 165 mm 19 mm
166 to 190 mm 22mm
191 to 219 mm 32mm
8. SiBver and ribbon tappers (cotton).-The calender drums
and the lap spool shall be provided with a guard to prevent access
to the nip between the in-running rolls.
9. Speed frames.-Jack box wheels at the head stock shall
be guarded and the guard shall have interlocking arrangement.
10. Spinning mules.-Wheels on spinning mule carriages
shall be provided with substantial wheel guards, extending to
within 6 mm of the rails. .
U. Warpers.-Swiveled double-bar gates shall be installed
on all warpers operating in excess of 410 metres/min. These gates
shall have interlocking arrangement, except for the purpose of
inching or jogging:
Provided that the top and bottom bars of the gate shall be
at least 1.05 and 0.53 meters high from the floor or working
platform, and the gate shall be located 38 mm from the vertifial
tangement to the beam head.
R.53] TAMIL NADU FACTORIES RULES, 1950
(2) Garnett fancy rolls shall be enclosed by guards. These
TAMIL NADU FACTORIES RULES, 1950 fR53
12. Slashers. -- (1) Cylinder Dryers. -- (a) All open nipe of in
running rolls shall be guarded by nip guards conforming to the require
ments in paragraph 2.
(b) When slashers are operated by control levers, these levers
shall be connected to a horizontal bar or treadle located not more than 170
cm. above the floor to control the operation from any point.
( c) Slashers operated by push button control shall have stop
and start buttons located at each end of the machine and additional
buttons located on both sides of the machine at the size box and the
delivery end. If calender rolls are used, additional buttons shall be
provided at both sides of the machine at points near the nips, except when
slashers are equipped with an enclosed dryer as in paragraph (b).
(2) Enclosed hot air dryer. -- (a) All open nips of the top
squeezing rollers shall be guarded by nip guards conforming to the re-
quirements in paragraph 7 (2). I
(b) When slashers are operated by control levers, these levers
shall be connected to a horizontal bar or treadle located not more than 170
cm. above the floor to control the operation from any point.
( c) Slashers operated by push button control shall have stop
and start buttons located at each end of the machine and additional stop
and start buttons located on both sides of the machine at intervals spaced
not more than 1.83 meters on centres.
13. Looms. -- 1[(1)] Each loom shall be equipped with suitable
guards designed to minimise the danger from flying shuttles.
2[ (2) Beam weights for tension in beam shall be of such construction
so as to prevent it falling during its adjustment.]
14. Valves ofkiers, tanks and other containers. -- (1) Each valve
controlling the flow of steam, injurious gases or liquids into a kier or any
other tank or container into which a person is likely to enter in connection
with a process, operation, maintenance or for any other purpose, shall be
provided with a suitable locking arrangement to enable the said person to
1 Re-numbered by G.O Ms. No 1527, Labour, 20th July, 1988
2.Ins. ibid,
TAMIL NADU FACTORIES RULES, 1950
lock the valve securely in the closed position and retain the key with him
before entering the kier, tank or container.
(2) Wherever boiling tanks, caustic tanks and any other containers
from which liquids which are hot; corrosive or toxic may overflow or
splash, are· so located that the operator cannot see the contents from the
floor or working area emergency shut off valves which can be controlled
from a point not subject to danger or splash shall be provided to prevent
danger.
15. Shearing machines. -- All revolving bladeon shearing machine
shall be guarded so that the opening between the cloth surface and the
bottom of the guard will not exceed 10 mm.
16. Continuous bleaching range (Cotton and rayons). -- The nip
of all in-running rolls on open-width bleaching machine rolls shall be
protected with a guard to prevent the worker from being caught at the nip.
.: The guard shall extend across the entire length of the nip.
17. Mercerizing range (piece goods). -- (1) A stopping device shall
be provided at each end of the machine.
(2) A guard shall be provided at each end of the frame between the
in-running chain and the clip opener.
(3) A nip guard shail be provided for the in-running rolls of the
mangle and washers and the guard shall conform to the requirements in
paragraph 7 (2).
18. Tenter frame. -- (1) A stopping device shall be provided at each
end of the machine.
(2) A guard shall be provided at each end of the machine frame
at the in-running chain and the clip opener.
19. Paddels. --Suitable nip guard conforming to the requirement in
paragraph 7 (2) shall be provided to all dangerous in-running rolls.
20. Centrifugal extractors. -- (1) Each extractor shall be provided
with a guard for the basket and the guard shall have inter-locking
arrangement.
TAMIL l'JADU FACTORIES RULES, 1950 [R.53
(2) Each extractor shall be equipped with a mechanically or elec
trically operated brake to quickly stop the basket when the power driving
the basket is shut off.
21. Squeezer or wringer extractor water mangle, starch mangle,
back washer (worsted yarn crabbing machines, and decating machines).
-- All in-running rolls shall be guarded with nip guards conforming to the
requirements in paragraph 7 {2).
22. Sanforizing and palmer machines. -- (1) Nip guards shall be
provided on all accessible in-running rolls and these shall conform to the
requirements in paragraph 7 (2).
(2) Access from the sides to the nips of in-running rolls should be
fenced by suitable side guards.
(3) A safety trip rod cable or wire centre cord shall be provided
across the front and back of all palmer cylinders extending the length of
the fact of the cylinder. It shall operate readily whether pushed �r pulled.
The safety trip shall not be more than 170 cm. above the level at which (sic)
the from splashing the operator, the floor or working surface.
23. Rope washers. -- ( 1) Splash guards shall be installed on all rope
washers unless the machine is so designed as to prevent the water· or liquid
fro!" splashing the operator, the floor, or working surface.
(2) A safety rip rod, cable or wire centre cord shall be provided
across the front and the back of all rope washers extending the length of
the face of the washer. It shall operate readily whether pushed or pulled.
This safety trip shall be not more than 170 cm. above the level on which
the operator stands and shall be readily accessible .
.. .
24. Laundry washer, tumbler or shaker.>- (1) Each drying tum
bler, each double cylinder shaker or clothes tumbler, and each washing
machine shall be equipped with an inter-locking arrangement which will
prevent the power operation of the inside cylinder when the outer door on
the case or shell is open, and which will' also prevent the outer door on the
case or shell'from being opened.without shutting off the power and the
cylinder coming .to a stop. This should not prevent the movement of the
inner cylinder by means of a hand operated mechanism or an inching
device. · · . · .
(R.53 TAMIL NADU FACTORIES RULES, 1950
(2) Each closed barrel shall also be equipped with adequate
means for holding open the doors or covers of the inner and outer
cylinders or shells while it is being loaded-or unloaded. '
25. Printing machine (Roller type). -- (1) All in-running rolls shall
"-be guarded by nip guards conforming to the requirement in paragraph 7
(2).
(2) The engraved roller gears and the large crown wheel shall
be guarded.
26. Calenders. = The nip at the in-running side of the rolls shall be
provided with a guard extending across the entire length of the nip and
arranged to prevent the fingers of the workers from being pulled in
between the rolls or between the guard and the rolls, and so constructed
that the cloth can be fed into the rolls safely.
27. Roary staple cutters. -- The cutter shall be protected by a guard
to prevent hands reaching the cutting zone.
28. Plating machines. -- Access to the trip between the kn\fe and
card bar shall be prevented by a guard.
29. Hand baling machine. --An angle iron handle-stop guard shall
be installed at right angle to the frame of the machine. The stop guard
shall be so designed and so located that it will prevent the handle from
travelling beyond the vertical position should the handle slip from - the
operator's hand when the pawl has been released from the teeth of the
take up gear.
30. Flat work ironer. -- Each flat-work or collar ironer shall be
equipped with a safety bar or other guard across the entire front of the
seed or first pressure rolls, so arranged that the striking of the bar or guard
by the-hand of the operator or other person will stop the machine, The
guard shall be such that the operator or other person cannot reach into the
rolls without removing the guard. This may be either a vertical guard on
all sides or a complete cover. If a vertical guard is used, the distance from
the floor or working platform to the top of guard shall be not less than 1.83
' , metres.
SCHEDULE II
Cotton Ginning
[R.53
Line shaft. -- The line shaft or second motion in cotton ginning
factories;' when below floor level, shall be competely enclosed by a
continuous wall or tinclimbable fencing with only so many openings as are
necessary for access to the shaft for removing cotton seed, cleaning and
oiling, and such openings shall be provided with gates or doors which shall·
be kept closed and locked . .
SCHEDULE III
Wood-working machinery
1. Definitions. -- For the purposes of this schedule --
(a) Wood working machine means a circular saw, band saw,
planing machine, chain mortising machine or vertical spindle moulding
machine operating on wood or cork.
(b) Circular saw means a circular saw working in a bench (in
cluding a rack bench) but does not include a pendulum. or similar saw
which is moved towards the wood for the purpose of cutting operation.
( c) Band saw means a band saw, the cutting portion of which
runs in a vertical direction but does not include a log saw or band resawing
machine. ·
( d) Planing machine means machine for overhand planing or
for thicknessing or for both operations. •
.2. �topping and starting device. -- An efficient stopping and
starting device shall be provided on every wood working machine .. The
control of-this device shall be of such a position as to be readify and
conveniently operated by the person in charge in the machine.
TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU Faeromss Runes, 1950
3. Space around machines.—The space surrounding every
wood-working machine in motion shall be kept free from obstruc-
tion.
4. Floors—The floor surrounding every wood-working
machine shall be maintained in good and level condition, and shall
not be alicwed to become slippery, and. as far as practicable, shall
be kept free from chips or other loose material.
5. Training and supervision—(l) No person shall be
employed at a wood-working machine unless he has been sufliciently
trained to work that class of machine, or unless he works under the
adequate supervision of a person who has a thorough knowledge of
the working of the machine.
(2) A person who is being trained to work a woodawdrking
machine shall be fully and carefully instructed as to the dangers of
the machine and the precautions to be observed to secure safe
working of the machine.
6. Circular saws—Every circular saw shall be fenced as
follows :—
(a) Behind and in direct line with the saw there shall be a
riving knife, which shall have a smooth surface, shall be strong,
rigid and easily adjustable, and shall also conform to the following
conditions:
(i) The edge of the knife nearer the saw shall form an arc
of a circle having a radius not exceeding the radius of the largest
saw used on the bench.
(ii) The knife shall be maintained as close as practicable
to the saw, having regard to the nature of the work being done at
the time, and, at the level of the bench table, the distance between
the front edge of the knife and the teeth of the saw shall not exceed
12.7 millimetres.
(iii) For a saw of a diameter of less than 61 centimetres,
the knife shall extend upwards from the bench table to within 2.5
centimetres of the top of the saw, and for a saw of a diameter of
61 centimetres or over shall extend upwards from the bench table- to
a height of at least 22.9 centimetres.
(b) The top of the saw shall be covered by a strong and '
easily adjustable guard, within a flange at the side of the saw far-
thest from the fence. The guard shall be kept so adjusted that the
said flange shall extend below the roots of the teeth of the saw.
The guard shall extend from the top of the riving knife to a point
as low as practicable at the cutting edge of the saw.
rlll'
TAMIL NADU FAcroares Ruuas, 1950
(c) The part of the saw below the bench. table shall be
protected by two plates of metal or other suitable material one on
each side of the saw; such plates shall not be more than 15.2 centi-
metres apart. and shall extend from the axis of the saw outwards to
a distance of not less than 5.l centimetres beyond the teeth of the
saw. Metal plates, if not beaded, shall be of a thickness-of
at least 3 millimeters or, if beaded. be of a thickness of at least/3
millimetres.
7. Push sticks.—A push stick or other suitable appliance
shall be provided for use at every circular saw and at every vertical
spindle moulding machine to enable the work to be done without
unnecessary risk.
8. Band saws.+Every band saw shall be guarded as
follows :—
(a) Both sides of the bottom pulley shall be completely
encased by sheet or expanded metal or other suitable materials.
(b) The front of the top pulley shall be covered with sheet
or expanded metal or other suitable materials.
(c) All portions of the blade shall be enclosed or otherwise
'"urely guarded except the portion of the blade betWeen the bench
ta--, and the top guide.
9. Planing machines.-(l) A planing machine (other than
a planing machine which is mechanically fed) shall not be used‘for
overlfiand planing unless it is fitted with a cylindrical cutter
bloc .
(2) Every planing machine used for overhand planing shall
be provided with a “bridge
”
guard capable of covering the full
length and breadth of the cutting slot in the bench, and so construc-
aed
as to be easily adjusted both in a vertical and horizontal
motion.
(3) The feed roller of every planing machine used for
thicknessing, except the combined machine for overhand planing
and thicknessing, shall be provided with an efficient guard.
10. Vertical spindle moulding machines.—(l) The cutter
of every vertical spindle moulding machine shall be guarded by the
'
most eflicient guard having regard to the nature of the work being
performed.
'
, (2) The wood being moulded at a vertical Spindle moulding
machine shall, if practicable, be held in a jig or holder of such
construction as to reduce, as far as possible, the risk of accident to
the worker. .
'® 33 Tawi Naou Factories Ruiss, 1950
11, Chain mortising machines.~The chaia of every chain
mortising machine shall be provided with a guard which shail
enclose the cutters as far as practicable.
12. Adjustment and maintenance of guards.—The guards
and other appliances required under this schedule shall be—
(2) maintained in an efficient state,
(b) constantly kept in position while the machinery is in
motion, and
(¢) so adjusted s to enable the work to be done without
unnecessary risk.
13, Exemptions.—~Paragraph 6, §, 9and 10 shall not apply
to any wood-working machine in respect of which it can be proved
that other safeguards are provided, maintained and used which
render the machine s safe as it would be if guarded in the manner
prescribed in this schedule,
1[Schedule 1V
d Plastic Mills and Injection Moulding Machine
Rubber an
— For the purpos¢ of this Schedule, —
(@ ' Rubber Mill or Plastic Mills " shall mean n?aghines w_ith
rollers used in breaking down, cracking, washing, g{atmg, mixing refining
and warming rubber or rubber goods plastic or plastic compound ;
() * calendar ” shall mean machine with rolls used fgr
frictioning, sheeting coating and spreading of rubber compounds and plastic
or plastic compounds ;
@© * Injection Moulding Machine ’ !
machine wherein a heat-softened plastic material if forced from a cylinder
into a relatively cool cavity, which gives the article the desired shape.
2 Installation of machines. — Rubber and plastic Mills shall be so
installed that top of the front roll is not less than one metre above the floor or working
level, provided that in existing installations where the top of the front roll is below
this height, a strong rigid distance bar guard shall be fitted across the front of the
machine in such position that the operator cannot reach the nip of the roller from
the normal working position of the operator.
3. Safety Devices. — (1) (@) Rubber and plastic Mills shall be equipped
with hoppers so constructed or guarded that it is impossible for the operators to
comé into contact in any manner with the nip of the rolls or horizontal safety-trip
rods or tight wire cable across both front and rear, which will when pushed or pulled
operate instantly to disconnect the power and apply the breakes or to reverse the
rolls.
1. Definitions.
» shall mean a moulding
(b) Safety- trip rods or tight wire cable on rubber Mills shall
extend across the entire length of the face of the rolls and shall be located
not more than 170 centimeters above the floor or working level.
(2) (@) C‘alendar machines shall be equipped with horizontal
safel:y(-jmp rods or tight wire across both front and rear, which will when
pushed or pulled, operate instantly to disconnect the
brakes or to reverse the roll ; power and apply the
(h) Safety-trip rods or tight wire cables on i ! calendar machines shall
extend across the entire length of the face of the rolls and shall be located not more
than 170 centimeters above the floor or working level.
(¢) On eachside of all calendars ide of and near both ends of the face of
the rolls there shall be a vertical tight wire cable connecting with the bar tripping
1 N ‘ ubs. by GO. Ms. No.255, Labour and Employment (M2), 25th October 2013.
mechanism at the top and fastened to the frame within 30 centimeters of the (i
These cables should be positioned at a distance of not more than 30 centime,
from the face of the roll and at a distance of not less than 25 millimeters from
calendar frame
4. Maintenance and Safety Devices. Safety-trip rods and tight v,
cables on all rubber mills and calendars shall be examined and tested daily iny,
presence of the manager or other responsible person and if any defect is disclo,
by such examination and test, the mill or calendars shall not be used until such def,
has boe remedied. Record of such examination and testing shall be maintained
. Injection. Moulding Machine. — (1) A Suitable interlock arrangeme,
shall be provided and maintained so that moulds cannot be closed unless the frey,
safety gate is fully closed and on opening the front safety gate, the movement
moulds wall stop automatically. No access shall be available to the moulds throug
the safety gate.
(2) In addition to the above, a hydraulic safety arrangement shal
also be incorporated with the front safety gate. This shall prevent the ta
stock mould plate from moving forward on opening of the front safety gate
(3) At the rear of the machine there shall be provided either z |
efficient fixed guard or a sliding gate which shall be suitably inter-locke:
with the movement of the mould plates in the manner of the front safel
gate as required under —
(1) above so as to prevent access to the danger zone of the
moulds in motion from the rear.
(4) The injection unit and all other accessible parts shall b
adequately insulated or guarded and warning signs shall be displayed where
hot parts are necessarily exposed.
6. Safety Precautions. — (1) Suitable provisions shall be provided and
maintained for collection and removal of gases and fumes from the source of
generation 1o outside of the workroom.
(2) Workers shall be provided with suitable personal protectivé
cquipment 1o prevent burns from contact with hot surfaces or splatters of
hot plastic and gases.
~ 3) Wnitten safe sysiem of work shall be developed and followed fof
safety of all workers working on the machine, mould changing and maintenance work
and all such workers shall be adequately trained and instructed in the safe method
of work before being employed B
TAMlL NADU FAcroaras RULES, L950 ‘ R. 53]
or other responsible person and, if any defect is disclosed by such
examination and test, the mill shall not be used until such defect
has been remedied.
SCHEDULE V
1. Special rule for printing presses
In printing works, every platen machine driven by power shall
be fitted with an efi‘icient‘finger-guard and every guillotine machine,
'driven by power, with an efficient knife-guard.
2. Special rule for jutermills
In Jute mills—
(a) the feed table of every softner machine shall; as' far. as
practicable, be not less than 1.5 metres in length ;
(b) the feed table of web softner machine shall be provided
with an automatic knocking ofi‘ device which shall stop-
the machine in case the worker’s hand is drawn in and prevent the:
hand from reaching the spiked rollers ; and
(c) the automatic device mentioned in clause (b) shall; be
maintained in an efficient state and be kept in position whenever
the machinery is working.
3. Special rule for tea factories
. In tea factories, the roll table shall be fenced to the satisfaction
of the Inspector and brushes shall be provided to the workers for
the purposes of sweeping the roll table.
4. Special rule for bricks and tiles works
In brick and tile works, a finger-guard shall be fitted at the
feed end to the full length of the mould of every revolving press.
5. Special rule for decorticating factories
In decorticating factories, the beater armsand the feed mouth
of the decorticator shall, as far as practicable, be guarded as
follows :—
A grating of 19 millimetres diameter wrought iron rods spaced
64 millimetres apart and supported by iron stifi‘eners 5.1 centimetres
by 6 millimetres thick shall be fixed at a height of 15.2 centimetres
above the tip of the beater arms. A strong wooden plank 38
millimetres thick and iron plated on the underside shall be clamped
with bolts and nuts over this grating leaving a space of 20.3
Rectangle
is. 5'3 TAMIL NADU FACTORIES RULES, I950
centimetres wide for the feeding of groundnuts. A grating of 2.5
centimetres diameter wrought iron rods spaced 38 millimetres apart
.
shall be fixed at a height of 12.7 centimetres just above the feed
mouth and another wooden plank"22.9 centimetres wide shall be
fixed over the full length of the decorticator platform.
6. Special rules for factories in which polishing and
grinding machinery are in use.
Safety devices-(a) All collars, set screws, shafts, couplings,
clutches, keys, pulleys, keys and belts in polishing and grinding
machines shall be effectively guarded.
(b) (i) Defective wheels shall not be used.
(ii) Grinding wheels shall fit freely on their spindles.
They shall never be forced on, nor shall they be let loose on
spindles.
(iii) The soft metal bushings at the centre shall not extend
beyond the sides of the wheels. Wheels shall be kept as true as
practicable and work rests shall be kept adjusted close to wheels.
(iv) Wherever possible. acompressible medium, such as
blotting paper, rubber or similar material, at least as large in
diameter as that of the flanges, shall be fitted between a wheel and
each of its flanges.
(v) Projecting arbor ends of grinding and polishing
wheels shall be effectively guarded.
‘
(0) Except with the written permission of the Chief
inspector no emery or abrasive 'wheel shall be kept unprovided with
a strong iron cover guard that shall enclose the wheel as far as
practicable to retain fragments in the event of bursting. The guard
shall be securely attached to the frame of the machine or other
solid foundation.
(d) Where workers are employed continuously on dry
grinding or polishing wheels. such wheels shall be provided with an
efficient exhaust system capable of drawing ofl‘ dust particles.
(e) Wheels shall not be operated at a 'speed in excess of
that which is recommended by-the manufacturer.
SCHEDULE VI
All factories
(a) Wherever practicable and considered necessary by the
inspector, service platforms and gangways shall be provided for
overhead shaftin g and where required by him these shall be securely
fenced with guards, rails and toe boards.
TAMIL NADU FACTORIES RULES, 1950 .R' 53] f
(b) Safe access shall be provided to all bearing clutches,
belt shifting levers and all such other appliances which are required
to be handled or operated while the machinery is at work.
(0) All ladders used in replacing belts or in attending
similar overhead machinery shall be specially made for that work
and provided with books or an effective non-skid device.
((1) No transmission machinery in motion shall be cleaned
with cotton waste, rags or similar materials held in hand.
(e) All belts shall be regularly examined to ensure that the
joints are safe and the belts are kept in proper tension.
(f) Each water gauge glass ofa boiler shall be fitted with an
elficient guard. .
(g) All condenser pipes of steam engines and exhaust pipes
of oil engines shall be adequately guarded. _
l[SCHEDULE Vll
’[Safety of Centrifugal Machines]
1. Centrifugal machine shall be provided with sufficient inter-
locking devices that will physically prevent the lids from being,
opened whilst the rotating drums or baskets are in motion under
power or due to power derived earlier and by then, switched off and
also prevent the starting of the drums or baskets under power while
the lids are open.
~
2.
.
The above requirements shall not apply while charging,
plo-Jghmg and discharging operations are carried out when the
drums or the baskets are rotated at lower speed.
3. Centrifugal machines shall not be operated at a speed in
excess ofthe manufacturer’s rating which shall be legiblv stamped
by the manufacturers both on the inside of the basket and on the
outside of the machine casing at easily visible places.
4. All centrifugal machines shall be provided with effective
breaking arrangements ’[for bringing the] cage, drum or basket to
rest within a reasonable short period of time after the power to
drive the motor is cut off.
5. The cages, drums or baskets shall be thoroughly examined
by a competent person once in every twelve months to check their
1 Ins. by 6.0. Ms. No. 35, Labour and Employment, dated the 19th
January. 1978.
2 Heading subs. by G. 0. Ms. No. 3236, Labour, d t d
December, 1983.
ac the 24th
3 Subs. by 6.0. Ms. No. 1%”, Labour and Em lo ment d
November, 1979.
p Y , ated the 8th
lRi 53 TAMIL NADU FAClORlES RULES, 1950
balance and in case balance at high speed is not observed, effectiVe steps
shall be taken to restore their'balance before recomissioning the ma-
chines]
’
l[SCHEDULE VIII
Power Presses
1. Application -- The schedule shall apply to all types of power
presses including press brakes, except when used for working hot metal.
2. Definition. -- For the purpose of/this Schedule, -—
i
(a) “approved” means approved by the Chief Inspector ;
(1)) “fixed fencing” means fencing provided for the tools of a
power press being fencing which has no moving part associated with or
dependent upon the mechanism of a power press and includes that part
of a closed tool which acts as a guard ;
'
'
'7
(c) “power press” means a machine used in metal or other
industries for moulding, pressing, blanking, raising drawing and similar
‘
purposes ;
(d) “safety device” means the fencing and any other safeguard
provided for the tools of a power press.
‘
3. Starting and stopping mechanism. -- The starting and stopping
mechanism shall be provided with a safety stop so as to prevent over
running of the press or descent of the ram during tool setting, etc.
4. Protection of tool and disc. -- (1) Each press shall be provided with
a fixed guard with a slip plate on the underside enclosing the front and all ~
sides of the tool.
(2) Each disc shall be provided with a fixed guard surrounding its
front and sides and extending to the back in the form of a tunnel through»
which the pressed article falls to the rear of the press.
'
(3) The design, construction and mutual position of the guards
referred to in sub-paragraphs (1) and (2) shall be such as to preclude the
possibility of the worker’s hand or fingers reaching the danger zone.
1 Added by 6.0. Ms: No, 1527, Labour, dated the 20th July, 1988.
TAMIL NADU FACIDRIES RiJuas, 1950 R, 53]
_ (4) The machine shall be fed through a small aperture at the
bottom of the guard but a wider aperture may be permitted for a second
or subsequent operations if feeding is done through a chute.
(5) Notwithstanding anything contained in sub-paragraphs (1)
and (2) an automatic or an inter-locked guard may be used in place of a
,fixed guard, but where such guards are used they shall be maintainedin
an efficient working condition and if any guard develops a defect, the
power press shall not be operated unless the defect of the guard15
removed.
5. Appointment of persons to prepare power presses for use. --
(1) Except as provided in paragraph 6, no person shall set, re-set, adjust
or try out the tools on a power press or install or adjust any safety device
thereon, being installation or adjustment preparatory to production of die
proving, or carry out an inspection and test of any safety device thereon
‘ required by paragraph 8 unless he --
(a) has attained the age eighteen ;
(b) has been trained in accordance with the sub--paragraph
(2); and
(c) has been appointed by the Occupier of the Factory to carry out
those duties in respect of the class or description of power press or the
class or description ofsafety device to which the power press or the safety
device (as the case may be) belongs ; and the name of every such person
shall be entered in a Register in Form 35. - -
(2) The training shall include suitable and sufficient practical
instruction in the matters in relation to each type ofpower press and safety
device in respect of which it is proposed to appoint the person being
trained.
6. Examination and testing of power-presses and safety devices. --
(1) No power press or safety device shall be taken into use in any Factory
for the first time in that factory or in case ofa safety device for the first time
on any power press, unless it has been thoroughly examined and tested, in
, the case of a power press, after installation in the factory, or in the case of
a safety device, when in position on the power press in connection with
which it is to be used.
(2) No power press shall be used unless-it has been thoroughly
examined and tested by a competent person, within the immediately
preceding period of twelve months.
iR- 53 TAMIL NADU FAcroruas RULES, 1950
(3) No power press shall be used unless every safety device (other
than fixed fencing) thereon has within the immediately preceding six
months when in position on that power press been thoroughly examined
and tested‘by a competent person.
(4) The competent person carrying out an examination and test
under the foregoing provisions shall make a report of the examination and
test containing the following particulars and every such report shall be
kept readily available for inspection, namely: --
(a) name of the occupier of the Factory;
(b) address of the Factory ;
(c) identification number or mark sufficient to identify the
power press or the safety device ;
(d) date on which the power press or the safe device was first
taken into use in the Factory ; x
(e) the date of each periodical thorough examination carried
7
Out as per requirements of sub-paragraph (2) above ;
(f) particulars of any defects affecting the safe working ‘of the
power press or the safety device found at any such thorough examination
and steps taken to remedy such defects.
7. Defects disclosed during a thorough examination and tests. --
(1) Where any defect is disclosed in any power press or in any safety device
by any examination and test under paragraph 6 and in the opinion of the
competent person carrying out the examination and test, either --
(a) the said defect is a cause of danger to workers and in
consequence the power press or safety device (as the case may be) ought
not to be used until the said defect has been remedied ; or
(b) the said defect may become a cause of danger to workers
and in consequence the power press or the safety device (as the case may
be) ought not to be uked after the expiration of a specified period unless
the said defect has been remedied; such defect shall, as soon as possible
after the completion of the examination and test, be notified in writing by
the competent person to the Occupier of the Factory and, in the case of
a defect falling within clause (b) of this paragraph such notification shall
include the period within which, in the opinion of the competent person,
the defect ought to be remedied.
(2) In every case where notification has been given under this
paragraph, a copy of the report made under sub-paragraph (4) of
TAMIL NADU FACTORIES RULES, 1950
[R 53
paragraph 6 shall be sent by the competent person to the Inspector for the
area within fourteen days of the completion of the examination and test.
(3) Where any such defect is notified to the Occupier in accor-
dance with the foregoing provisions of this paragraph the power press or
safety device ( as the case may be ) having the said defect shall not
be used --
(a) In the case of a defect falling within clause (a) of sub-
paragraph (1) until the said defect has been remedied ; and
(b) In the case of defect falling within clause (b) of sub-
paragraph (1), after the expiration of the said defect has been remedied.
(4) As soon as is practicable after any defect of which notification
has been given‘under sub-paragraph (1) has been remedied, a record shall
be made by or on behalf of the Occupier stating the measures by which
and the date on which the defect was remedied;
8. Inspection and test of safety devices. -- (1) No power press shall
be used after the setting, resetting or adjustment of the “5015 thereon
unless a person appointed orauthorised for the purpose under paragraph
5 has inspected and tested every safety device thereon while it is in position
on the said power press :
/
Provided that an inspection, test and certificate as aforesaid shall not
be required where any adjustment of the tools has not caused or resulted
in any alteration to or disturbance ofany safety device on the power press
and if, after the adjustment of the tools, the safety devices remain, in the
opinion of such a person as aforesaid, in efficient working order.
(2) Every power press and every safety device thereon while it is
in position on the said power press shall be inspected and tested by a
trained person every day.
9. Defects disclosed during an inspection and test. -- (1) Where it
appears to any person as a result of any inspection and test carried out by
him under paragraph 8 that any necessary safety device is not in position
or is not properly in position on a power press or that any safety device
which isin position on a power press is not in his opinion suitable, he shall
notify the manager forthwith.
(2) Except as provided in-sub-paragraph (3) of this paragraph
where any defect is disclosed in a safety device by any inspection and test
under paragraph 8, the person carrying out the inspection and test shall
notify the manager forthwith.
M
TAMIL NADU FACI‘ORIE RULE, 1950
(3) Where any defect in a safety device is the subject of a
notification in writing under paragraph 7 by virtue ofwhich the use ofthe
safety device may be continued during a specified period without the said
defect having been remedied, the requirement in sub-paragraph (2) of
this paragraph shall not apply to the said defect until the said period has
expired.
10. Identification of power presses and safety devices. —- For the
purpose of identification every power press and every safety device
provided for the same shall be distinctively and plainly marked.
11. Training and instructions to operators. -- The operators shall be
trained and instructed in the safe method ofwork before startingwork on
any power press.
12. Exemptions. -- (1) If in respect ofany factory, the Chief Inspector
is satisfied that owing to the circumstances or infrequency of the processes
_
or for any other reason, all or any of the provisions of this Schedule are not.
necessary for the protection of the workers employed on any power press
or any class or description of power press in the factory, the Chief
Inspector may by a certificate in writing (which he may in his discretion
revoke at any time), exempt such factory from all or any ofsuch provisions
subject to such conditions, if any, as he may specify therein.
(2) Where such exemption is granted a legible copy of the
certificate, showing the conditions (if any) subject to which it has been
granted, 'shall be kept posted in the factory in a position where it may be-
conveniently read by the persons employed.
l[SCHEDULE IX
Shears, Slitters and Guillotine Machines.
1. Definitions. -- For the purpose of this Schedule, --
(a) “guillotine” means a machine ordinarily equipped with straight,
beveledged blade operating vertically against a stationary resisting edge
and used for cutting metallic or non-metallic substances;
(b) “shears” or “shearing machine” means a machine ordinarily
equipped with straight, bevel-edged blades. operating vertically against
1
Added by 6.0. M5. N0. 1527, Labour, dated the 20th July, 1988.
TAMIL NADU FAcromns Rum, 1950 [R. 53
resisting edge, or with rotary, overlapping cutting wheels and used for
shearing metals or non-metallic substances;
(c) “slitter” or slitting machine” means a machine ordinarily
equipped with circular disc-type knives and used for trimming or cutting
into metal or non-metallic substances or for slitting them into narrow
strips; for the purpose of this schedule, this term includes bread or other
feed slicers equipped with rotary knives or cutting discs.
2. Guillotine and Shears. -- (1) Where practicable, a barrier metal
guard of adequate strength shall be provided at the front of the knife,
fastened to the machine frame and shall be so fixed as would prevent any
part of the operator’s body to reach the descending blade from above,
below or through the barrier guard or from the sides:
Provided that in case of machines used in‘the paper printing and
allied industries, where a fixed barrier metal guard is not suitable on
account of the height and volume of the material being fed, there shall be
provided suitable starting devices which require simultaneous action of
both the hands of the operator or an automatic device which will remove
both the hands of the operator from the danger zone at every descent of
the blade.
(2) At the back end of such machines an inclined guard shall be
provided over which the slit pieces would slide and be collected at a safe
distance in a manner as would prevent a person at the back from' reaching
the descending blade.
(3) Power-driven guillotine cutters, except continuous feed trim;
mers, shall be equipped with :-
(a) starting devices which require the simultaneous action of
both hands to start the cuttingmotion and of at least one hand on a control
during the complete stroke of the knife ; or
(b) an automatic guard which will remove the hands of the
operator from the danger zone at every descent of the blade, used in
conjunction with one-hand starting devices which require two distinct
movements of the device to start the cutting motion, and so designed as
to return positively to the non-starting position after each complete cycle
of the knife.
(4) Where two or more workers are employed at the same time on
the same power-driven guillotine cutter equipped with two-hand control,
R. 53] TAMIL NADU FACToRiEs RULES, 1950
-the device shall be so arranged that. each worker shall be required to use
both hands simultaneously on the safety trip to start the cutting motion, and
atleast one hand on a control to complete the cut.
(5) Power-driven guillotine cutters, other than continuous trim-
mer, shall be provided, in addition to the brake or other stopping mechanism,
with an emergency device which will prevent the machine from operating in
the event of failure of the brake when the starting mechanism is in the non—
starting position.
3. Slitting machine. — (l) Circulars disc-type knives on machines
for cutting metal and leather, paper, rubber, textile or other non-metallic sub—
stances shall, if within reach of operators standing on the floor or working
level, be provided with guards enclosing the knife edges at all times as near
as practicable to the surface of the material and which may either, —
(a) automatically adjust themselves to the thickness of the
material ; or
(b) be fixed or manually adjusted so that the space between the
bottom of the guard and the material will not exceed 6 mm. (1/4 inch) at any
time.
-
(2) portion of blades underneath the tables or benches of
slitting machines shall be covered by guard.
4. Index cutter and Vertical Paper slotters. —- Index cutters, and
other machines for cutting strips from the ends of hooks, and for similar
operations, shall be provided with fixed guards, so arranged that the fingers
of the operators cannot come between the blades and the tables.
5. Corner cutters. —— Corner cutters, used in the manufacture of
paper boxes, shall be equipped with, ——
'
(a) suitable guard, fastened to the machines in front of the knives
.and provided with slots'or perforations to afford visibility of the opera-
tions ; or
(b) other guards equally efficient for the protection of the fin-
gers of the workers.
6. Band Knives. — Band wheels on band knives and all portions of
the blades except the working side between the sliding guide and the table
on vertical machines, or between the wheel guards on horizantal machines,
shall be completed enclosed with hinged guards of sheet metal not less than
1 mm. (0.04 inch) in thickness or of other material ofequal strength]
TAMIL NADU FACTORIES RULES. 1950 [R. 53
l[SCHEDULE X
Paper, Paper Board and Corresponding Machines
for Pulp Production.
1. Application. —- The requirements of the Schedule shall apply to
machinery in manufacture of paper, paper board and also to the correspond-
ing machines for pulp production.
2. Definitions. —' For the purpose of this schedule :
(a)
(b)
(C)
(d)
(8)
(f)
(g)
(h)
(i)
(j)
(k)
(I)
(/11)
“approach safety stop” means a safety device which automati—
cally removes a hazardous function when part of a body comes
within dangerous proximity of the danger zone ;
_“ broke
”
means paper or paper board wasted out during pro-
cessing ;
“broke Guilletine
”
means a machine with a straight knife for
cutting up broke or paper reels ;
“Calender” means a machine for glazing paper or paper board ;
a“
Calender work platform
’
Calender;
means a lifting platform at a
“
Constant Pressure Switch
”
means a start and stop switch
automatically returning to the stop position when not
'
actuated ;
“Cross cutting knife ”means a knife mounted on a cylinder roll
cross cutting the web ;
“drum reel up” means a machine (pope reel) for reeling up the
web on an empty spool, friction-driven ;
“
nip point
”
means roll nip or any other place where faces con-
verge or run so close together that part of the body is in danger
of being caught and injured :
“
pulper
”
means a machine for making fibre suspension by.
mechanical treatment of pulp or paper broke ;
“reeling Drum or Spool means a roll for reeling up the web in
full machine width at the drum reel-up;
“
threading
”
means feeding a narrower pointed web (tail end)
through a machine ;
web
"
means pulp, paper or paper-board in the shape of a
continuous carpet during manufacturing or processing.
'
Added by (3.0. Ms. No. l54. Labour and Emplyment (M2). dated the 151 June 2004
R. 53} TAMlL NADU FACTORIES RULES, 1950
3. Safety Measures against Nip Hazards. — (l ) General. — Nip
points shall, when possible be inaccessible from floor level or from any other
surface that can easily be stepped on. If this requirement cannot be satisfied
the risk must be avoided in some other way, like air jet/chute, carrier ropes,
carrier belt or felt. The platforms should have the board of atleast 100
millimetres high and two handrails at a height of 400 millimetres and at 900
millimeters. The vertical members of the platform should be spaced at 1 metre
for cross platform and 2 metres for longitudinal platform.
(2) Threading. —— Threading shall be done without manual inter-
ference when feasible. If threading must be done manually, measures must
be taken to achieve adequate safety as in paragraph (1) above.
- 4. Reeling Drum Exchange. —- Feeding during spool exchange at
the drum reel up shall be effected only by using air jet or air hose, if the speed
of the paper machine exceeds 100 metres per minute. If the speed of the
machine is less than 100 metres per minute the feeding may be done manu-
ally, but measures must be taken to safety during the operation.
5. Safety measures against risks of being squeezed or knocked
down. — The movement of machine part or other technical device must not
expose anybody to the risk of being squeezed, knocked down or injured. If it
cannot be ensured that the danger—zone is inaccessidn when a risk is present,
the moving device must be equipped with an approach safety stop. Its move-
ment controlled by a hand—operated constant pressure switch or the risk
avoided.
6.. Web Reeling. — (1 ) Web reeling shall be arranged so that the reel
cannot cause injury by moving without control from its intended position by
providing a cradle or a protection barrier.
(2) When a reel is carried by a through shaft, a device must, if
necessary, be arranged to keep the shaft ends in their intended position.
(3) When a reel is carried and substantially governed by resting
on two rolls, an ejection shield must be arranged ,to stop any reel, ejection
when the web speed exceeds 15 metres per minute. If the shield is movable,
a web speed exceeding 15 metres per minute must not be attainable unless
the shield is in its protective position. The shield must not be removable
from that position if the web speed exceeds the above value.
7. Handling of reels. —— ( l) A reel must not be automatically put in
free motion on a floor level or surface that can easily he stepped on unless
this can be done with adequate safety.
TAMIL NADU FACTORIES RULES, 1950 IR. 53
(2) A reel discharger shall be arranged and handled so that no—
body can be injured by its function or by the discharge reel.
(3) The discharger must not come into operation unless mea-
sures are taken to receive the discharger reel safety, if necessary, the dis—
charger shall be controlled by a hand-operated constant pressure switch
from a place where the operator can supervise both the zone ofmovement 0f
the discharger and the course of the discharged reel.
(4) A reel lifted by the ends of a through shaft must not rotate
unless the shaft ends and the lifting equipment can stand the stress caused
by the rotation.
8. Cutting of paper.
—— (1) A power-driven sharpedged tool for
cutting paper shall be shielded against inadvertant contact and, as far as
possible, inaccessible while in operation.
(2) A cross—cutting knife shall be shielded so that the tool is
inaccessible when in operation. It must not be possible to start the tool
unless the shield is in its protective position and. it must not be possible to
open the shield unless the tool is inoperative and its energy supply has been
cut off by a safety sWiteh which can be locked in its off-position.
9. Pulpers, pulp chests, etc. —— (l ) The opening of a pulper, a pulp
chest another reservoir of a feeding service shall be arranged so that
nobody is in danger of falling or stepping down through the opening.
(2)_ A pulper and its feeding device shall have ajoint emergency
stop and.if possible a joint energy cut-off device. lockable in the off—
position.
(3) Broke holes should not be allowed to become covered by
paper or broke which may hide them from operating personnel.
10. Certain devices moving vertically. — (l) Calender work
platforms, pallet table, rider rolls, ejection shields, reel lowering devices, lids
ol‘driving section covers broke guilletine knives or other stationery devices,
which for functional reasons are regularly manoeuvered to considerably
different heights, shall be constructed. handled and maintained in such a
way that they do not cause any risk of injury by falling down or in any other
way and must not be liable to fall down as a result of interruption or variation
in the energy supply.
(2) An operating movement that can cause risk ofinjury shall be
controlled by a constant pressure switch from a place where the operator
can supervise the zone of movement.
R. 53] TAMIL NADU FACTORIES RULES, 1950
(3) A device as referred to in paragraph ( 1) above carried by a
wire rope or chain shall have the requisite derailment protection and a
breaker to stop the movement if the wire rope or‘chain should slacken or
burst.
‘
(4) If operationally stopped in a position where it could cause
a risk' of'injury by falling down, the device shall be automatically
secured.
(5) The hoisting equipment of a device as referred to in para—
-
graph (1!): above shall be readily available for full inspection...
11. Calender Work Platform. —— ( l) Calender work platform shall be
longer than the width of the calender roll and provided with a gate or
opening bar. The gate may only be openable inward or the bar may only be
openable upwards and it must not be capable of staying open. The bar shall
contain atleast two rails.
(2)
*
A calender super work platform shall be controlled by a con-
stant pressure switch, located on the platform.
(3) Along the work side of the platform there shall be an emer—
gency stop controlling the "movement of the platform as well as the calender
bowl rotation. '
(4) The hoisting and lowering speed must not exceed 0.15 metre
per second.
(5) A hydraulic cylinder being part of the hoisting gear of a
calender work platform shall have a valve which, in the event of a hose or
pipe fracture or considerable leakage, prevents the platform from moving
downwards or retards its descent. Such a valve shall be mounted in or
directly on the cylinder.
(6) A calender super work platform carried by wire rope or chain
shall have a reliable ‘catch.
(7) An elevating screw of a calender Work platform shall be
self broking bearing nuts and safety nuts shall serve as load—carrying
devices.
12. Examination and Inspection. — (l ) A device as referred to in
paragraph 10 ( l ) abo‘we. shall when needed and atleast twice a year, and in
case of a calender work'platform once a month. is subjected to thorough
examination by a competent person as long as it is being used. Ifa calender
work platform has been out of use for more than three months, thorough
examination shall be carried out before it is used again.
TAMIL NADU FACTORIES RULES. l95t) IR. 53
(2) In the course ol‘examitmtion. a check shall be made to ensure
that safety devices are in working order and also that the hoisting and
towering speed of the calender work platform does not exceed the permitted
value.
(3) An examination log book shall be maintained and ‘made
readily available.
13. Hose Pipes. — (l ) A hose pipe used for cleaning near a rotating
pair of rolls shall have a rounded nozzle or otherwise be arranged so that the
nozzle cannot be caught in the nip.
(2) A hose used for flushing liquid at a pressure exceeding
25 Kilogram/Centimetre shall have a constant pressure actuated valve for
flow control. If needed for safety during handling the nozzle shallfbe mounted
on a stand or the hose designed for two operators.
14. Space inside a machine. — Any opening leading to a walkable
passage into or through a machine must be blocked. This does not apply if
the passage must be accessible for operational or maintenance purpose on
condition that entering does not involve any risk.
\15. Inching. — If it is necessary, to operate a machine temporarily
without the protective devices otherwise provided, the speed of the web
shall be aslow as possible and shall not exceed 15 metres per minute. The
machine shall be governed by a hand operated constant pressure switch
from a place where the operator can supervise those places where protective
devices have been rendered inoperative.
16. Emergency stop. — An emergency stop must not break the
energy supply to any device needed in an emergency or provoke
any movement that might aggraVate the situation. Braking provoked by
the emergency stop must not be so violent as to cause any risk of
injury.
17. Auxiliary measures. — In place where large quantities ofpulp
or broke are frequently handled, measures shall be taken to facilitate the
work. Special attention shall be paid to the need for such measures in places
where there are high temperatures.
18. Work Instructions. — ( l ) Instructions shall he provided for the
work routines necessary to promote safety during normal operation as well
as during maintenance cleaning supervision and similar kinds ofperiodically
recurrent tasks.
R. 54-A] TAMIL NADU FACTORIES RULES, 1950
(2) Work permit system should be adopted for maintenance and
cleaning operations.
19. Other Safety Precautions. — (l) Wherever risk of injury
prevails, necessary caution boards or symbols should be displayed like
moving equipments, Nip points, slippery area, men at work, etc.
(2) Adequate training in safe operations should be imparted to
workers at the time of induction into the factory and at periodical intervals
not exceeding a year and whenever there is a job rotation or operational
changes.
(3) For paper machine speeds exceeding 200 metres per minute
start up alarm should be provided before crawl and before being put to run.
(4) All rotating elements should indicate direction of rotation.
(5) Wherever nip is there, indication in bold letter to be provided]
THE TAMIL NADU FACTORIES RULES, 1950 [R.53
l[SCHEDULE — XI
Conveyors
PART-A — General
1. Definition. —— For the purposes ofthis Schedule, —
“
Conveyor
”
means a horizontal, inclined, or vertical device for
moving or transporting material of any kind, in a path determined by
the design of the device, and having points of loading or discharge and
the device shall include skip hoists, but shall not include devices like
cranes, hoists, monorails, bucket drag lines, platform elevators, plant
railways, cableways and tramways.
2. Design, construction and maintenance, etc. — (1) Conveyor
shall be of good design, proper construction, sound material, adequate
strength and free from defects and shall be properly maintained.
(2)
‘
In running nips
’
shall be securely fenced by safeguard
of substantial construction or by any other suitable device.
(3) Conveyor shall be installed in such a way that a clearance
of atleast 45 centimeters shall be provided between the conveyors side
of the passage way and the conveyor. Hand rails or railings shall be
provided on open sides of the walkway all along the belt.
(4) When workers have to cross over conveyor, regular
crossing facilities affording safe passage shall be provided.
(5) Suitable device like gongs, whistles or signal lights shall
be provided to the operator to warn the workers before starting the
conveyor.
(6) (a) The starting button or switch for the conveyor shall be
so located that the operator can see as much of the conveyor as
possible. The starting and stopping devices shall be marked distinctly
and so located that they can be clearly seen and safely approached.
(b) All personnel working on or around the conveyor shall
be made to have knowledge about the location and operation of all
stopping devices.
‘
Ins. by G.O. Ms. No. 40, Labour and Employment (M-Z), dated the 29th March
2006.
(7) Side guard of sufficient height and strength shall be provided
to prevent falling of material from the conveyor.
(8) (a) conveyors shall be tested and the parts thereof thoroughly
examined by a competent person before being taken into use for the
first time or after it has undergone any alteration or major repairs liable
to affect its strength or stability.
(b) A certificate of such tests and examinations signed by
the competent person making the tests and examinations specifying the
maximum safe conveying load shall be obtained and made available to
the Inspector on demand.
( c) Conveyors shall be thoroughly examined atleast once
in every twelve months by the competent person and report of the
competent person shall be made available to the Inspector on demand.
(9) Belt conveyors carrying materials which might stick to tail
drums or belts, shall be provided with fixed scrappers or revolving
brushes for removing the deposits to avoid the hazards in cleaning
the moving parts or pulleys by hand or shovels while the belts are in
motion.
(10) Conveyors shall be provided with automatic and
continuous lubrication systems or with lubricating facilities so arranged
that oiling and greasing can be performed without the oils coming within
the dangerous proximity to moving parts.
( 1 1 ) Before commencing any maintenance work, electrical or
mechanical, ' permit ' to work shall be obtained from the manager or
any person so authorized by the manager for the purpose and the
procedure laid down in the permit shall be strictly followed.
(12) The workers working on conveyor shall be adequately
trained.
(13) No person shall be required or allowed to ride on
conveyors.
3. Conveyor Guarding. - (1) The Underpasses of the conveyor
shall be securely guarded.
(2) All the transfer points of conveyors system shall be
adequately enclosed.
R.53] THE TAMIL NADU FACTORIES RULES, 1950
(3) Where the top of hopper for feeding conveyor is less than
90 centimetres above floor, the opening shall be adequately guarded.
( 4) All the areas underneath the counterweight of the conveyor
system shall be suitable (sic) barricaded so as to prevent any person getting
injured due to accidental fall of the ' counterweight '.
(5) Gears, sprockets, sheaves and other moving parts shall be
either adequately guarded or positioned in such a way as to protect
\ workers against personal injuries.
4. Safety Devices. - (1 ) A conveyor shall -
(i) stop when its driving power is cut-off and remain stopped I
until the power is reconnected ;
(ii) have a provision at each point of loading or delivery of
the conveyor, to stop the conveyor ;
(iii) not be capable of being restarted after having been
stopped until the device, if any, by which it is stopped is reset in the
running position ; and
(iv) where the conveyor can be stopped by means of a push
button have provision whereby the push button can be secured in the
stop position.
(2) (a) Chord shall be provided on both sides of the belt along
the walkway covering the entire length of the belt when pulled shall stop
the conveyor and the distance between two consecutive emergency stopping
devices of the chords shall not exceed 23 (twenty three) metres.
(b) For conveyers other than belt conveyors emergency
stopping devices shall be provided at the accessible points throughout
the length of the conveyors and distance between the two consecutive
devices shall not be more than 8 (eight) metres.
(3) Overload protection device shall be provided so that when
overloaded all starting devices shall get automatically tripped off. In
addition to such overload protection customarily provided for electric
motors, there shall be an overload device designed to protect the
conveyor and mechanical drive parts. In the event of an overload, the
device shall shut off the electric power quickly, disconnect the conveyor
or drive parts from the motive power, or limit the applied torque.
THE TAMIL NADU FACTORIES RULES, 1950 [R.53
4) When a conveyor has stopped because of an overload, all
starting devices shall be locked out and the cause of the overload
removed. The entire conveyor shall be inspected before it is restarted.
( 5) If two or more conveyers are operated in series, conveyors
shall be interlocked in such a way that if one conveyor is stopped all other
conveyors fed by it shall be stopped simultaneously.
(6) Conveyors which carry loads up inclines, shall be provided
with mechanical devices that will prevent machinery from reversing and
carrying the loads back towards the loading point in the event of the power
being cut-off.
(7) The precautions necessary to avoid the accumulation of the
static electricity shall be taken.
5. Personal Protective Equipment. - The worker engaged in
the operation of conveyors shall wear tight fitting clothing and use
appropriate personal protective equipment.
PART- B
Special Types of Conveyors
6. Gravity Conveyers. - ( 1 ) The delivery ends of the conveyors
shall be provided with electrically or mechanically operated devices to
give warning that a package is about to be delivered. ·
(2) To prevent the spread of fire, the chute conveyors shall
be-
(a) enclosed in shafts made of fire resisting materials, with
a door at each charging station and at the delivery end ; or
(b) provided with automatic fire doors or with draught
checks where the chutes pass through the floors.
(3) The gravity roller conveyors shall be provided with guides
or guard rails on each side of the conveyor way at corners or turns
and on each side of those portions of the conveyor way which are more
t�an 5 (five) feet above the floor.
7. Chain Conveyor. - ( 1) Overhead chain conveyor systems shall
be so designed and installed that ample clearance is provided between the
material transported and any fixed or moving objects.
R .53 ] THE TAMIL NADU FACTORIES RULES, 1950
(
(2) Apron conveyors used for carrying unpacked bottles, jars or
other glass containers shall be provided with side rails at a suitable distance
above the conveying surfaces to prevent the containers from tipping over
or falling off.
(3) Return portion of a chain conveyor shall be adequately
guarded.
8. Bucket Conveyors. - (I) Inclined bucket conveyors shall be
enclosed with solid guards which, -
(a) are not less than 7 (seven) feet in height, but preferably
extend to the full height of the machinery, so as -
(i) to prevent anything being pushed or thrown into the
shaft ways ; and
(ii) to hold any material which might drop from the
buckets ; and
(b) are provided with wire-glass windows or doors or with
removable sections to facilitate inspection, cleaning and repairs.
(2) Controls of movable tripping devices for bucket conveyors·
shall be so located that they can be operated from a safe position.
9. Screw Conveyors.- (I) Screw conveyors shall be placed in
steel or steel-lined trough fitted with well-secured tight covers of not
less than 3 (three) mm (1/8 inch) steel plates in removable sections
and should be provided with second covers of heavy wire mesh in
corresponding removable sections underneath the solid top covers so as
to guard the screw when the solid cover is removed for inspection of the
interior.
(2) Inside covers of screw conveyors, or outside covers where
so inside covers are provided, should be mechanically or electrically
interlocked with the control units or driving mechanisms in such a
manner that the power is automatically shut off whenever a section of
the cover is removed.
(3) No person shall be allowed/required to stand or walk on
housings of screw conveyors.
JO. Pneumatic Conveyors. - ( I ) Blower or exhaust fans for
pneumatic conveyors systems shall be -
THE TAMIL NADU FACTORIES RULES, 1950 [R.53
(a) of non-combustible construction;
(b) of adequate but not greatly excessive capacity properly to
perform the functions required ;
( c) firmly secured to substantial supports or foundations:
(d) so located and arranged as to afford ready and safe access
for cleaning inspection; lubrication and repairing ; and
( e) provided with remote control in addition to any controls
located close to the systems.
(2) Where readily ignitable materials are passed through fans for
pneumatic conveyor systems, the blades and spiders of the fans shall be
of non-ferrous material, or the casings shall be lined with non-ferrous
material.
(3) Blades or runners of blower or exhaust fans for pneumatic
conveyor systems shall be of sufficient strength to prevent contact with
casings or destortion under conditions of deposit loading or other
operating factors. .:
( 4) Housing or casings of blower or exhaust fans for pneumatic
conveyors shall be so constructed as to prevent distortion and loss of
alignment under operating conditions.
(5) Intake openings of blowers or exhaust fans for pneu
matic conveyors shall be protected with substantial metal screens or
gratings.
( 6) Bearing of blower or exhaust fans for pneumatic conveyors
shall be self-lubricating, dust-tight, and located outside casings and ducts.
(7) Ducts for pneumatic conveyor systems shall be constructed
of steel plate of adequate strength or other metal equal in strength to steel
plate.
(8) Ducts for pneumatic conveyor systems shall be -
(a) reasonably tight throughout, with no openings other than
those required for the proper operation and maintenance of the systems;
(b) substantially supported by metal brackets or hangers,
and thoroughly braced where required ; and
R.53] THE TAMIL NADU FACTORIES RULES, 1950 .
c) kept open and unobstructed throughout their entire length
with no screens inside them.
(9) Handholes for cleaning purposes in ducts for pneumatic con
veyors shall be equipped with tight-fitting sliding or swinging doors pro
vided with substantial latches.
( 1 O) Where material is fed by hand into pneumatic conveyors
through openings 30 (thirty) centimeters 12 (twelve) inches or larger,
provision shall be made to prevent worker from being drawn into the
ducts, such as by installing feed hoppers extending at least I (one) metre
- 40 (forty inches) from the ducts.
( 1 1 ) Doors of a pneumatic conveyor shall be so interlocked that
they cannot be opened when there is positive internal pressure and the
conveyor cannot be started unless all the doors are closed.].
I
54. · Employment of young persons on dangerous machines.
Rule prescri- - '[The machines specified in Sections 28, 29 and 30 and
bed under sub- the machines mentioned below) shall be deemed to be of
section (2) of
section 23• such dangerous character that young persons shall not work
· at them unless the provisions of section 23 ( l) are com
plied with : -
• Power presses other than hydraulic presses ; milling machines used
in the metal trades ;
Guillotine machines ;
Circular saws ;
Platen printing machines ;
Decorticator ;
Oil expeller,
54A. The following parts of machines will be deemed to be
Rule under machinery to be guarded by the makers for the purpose of
section 1:6 (3) section 26 (1) : -
( 1) The platen motion of letter printing machine.
(2) Reciprocating dies of power presses.
(3) Reciprocating knife of the guillotine machine.
(4) Revolving drums and cylinders in all machines, such as
groundnut seed crusher, soap mixtures and foundry tumblers.
(5) Revolving beaters in groundnut decorticator.
(6) Abrasive wheels.
I Subs. by GO. Ms. No. 248, Labour & Employment, dated the 26th March, 1976.
TAMIL NADU FACTORIES RULES, 1950 [R. 54-A
(
(7) Projections on revolving parts, such as keyhcads. set screws.
cotton pins and coupling bolts.
(8) Revolving open arm pulleys including fan blades.
(9) Back gears, change wheels and cog driver of lathes.
(10) Level drives of planing, shaping, slotting, drilling and mill
ing machines.
( 1 1 ) All cog and level drives of oil expellers.
Rules pre
scribed under
section 28.
SS. Hoists and lifts. -1(( I ) A Register shall be main
tained to record particulars of examination of hoists and
lifts and shall give particulars as shown in Form No. 36.]
(2) Exemption of certain hoists and lifts. - In pursuance of the
provisions of sub-section (4) of section 28, in respect of any class or
description of hoist or lift specified in the first column of the following
schedule, the requirements of section 28 specified in the second column of
the said schedule and set opposite to that class or description of hoist or lift
shall not apply.
SCHEDULE
Class or description of hoist or lift Requirements which shall not apply
( 1 ) (2)
Hoists or lifts mainly used for rais- Sub-section ( I ) (b) in so far as it re
ing materials for charging blast quires a gate at the bottom landing;
furnaces or lime kilns. sub-section ( 1) (d); sub-section ( I ) (e).
Hoists not connected with mechani
cal power and which are not used
for carrying persons.
Sub-section ( 1 ) (b) in so far as it
requires the hoist-way or lift-way
enclosure to be so constructed as to
prevent any person or th ing from
being trapped between any parts of
the hoist or lift and any fixed structure
or moving part; sub-section ( I ) (e).
Ru le pre- SSA. Lifting machines, chains, ropes and lifting tack-
sc ri bcd u n d e r . les. - ( I ) No lifting machine and no chain, rope or lifting
sub-section (2 ) tackle, except a fibre rope or fibre rope sling, shall be taken
of section 29· into use in any factory for the first time in that factory unless
it has been tested and a l l parts have been thoroughly examined by a com
petent person and a certificate of such a test and examination specifying the
' Subs, by S . R . O . A-No. 90177. dated the 23rd February, 1977 .
· T A M I L NADU FACTO�IES RULES, 1 9 5 0 [R. 55-A
R, SS-A] TAMIL NADU FACTORIES RULES, 1950 229
safe wufhing lead or loads and signed by the W150“ making the lest and the
examinauhn. has been obtained and Is kept available for inspection.
(2) Every jib crane so constructed that the safe working lead
may be varied by the raising or lowering at’ the jib, shall have attached
thereto either an automatic indicator of safe working loads or an automatic
jib angle indicatar and a table indicating the safe working loads at corre-
sponding inclinations of the jib or corresponding radii of the load.
(3) A table showing the safe working loads DI every kind and
size of chain, rope or lifting tackle in use. and in the case ofa multiple sling.
the safe working load at different angles of the legs. shall be posted in the
store in which the chains. ropes or lifting tackles are kept, and in pram!-
rtclll positions on the pretniees,—.1nd no chain. rope or lifting tackle net shown
in the table shall he used. This sub-rule shall not apply in resyect of any
lifting tackle if the safe working load thereof or in the case 01‘ a multiple
sling, the safe working lead at different angles of the legs is plainly marked
upon it
(4) ”file register to be maintained under clause (a) (iii) of sub-
section (1) of section 29 of the Act shall contain the following particular:
and shall be kept readily available for inspection : —
(1) Name ofoccupier of factory
(ii) Address of the factory,
(iii) Distinguishing number or mark, if any and description suf-
ficient to identify the lifting machine, chain, rope or the lifting lacklei
(iv) Date when the lifting machine. chain, rope nr lifting tackle
was first taken into use in the factory.
(v) Date and number of the certificate relating to any test and
examinarinn made under subrules (1) and (3) together with the name and
address of the person who issued the certificate.
(vi) Date of each periodical thorough examination made under
clause (a) (iii) of sub-section (1) afsectiun 29 of the Act and sub-rule (7) and
by whom it was carried out.
‘
(Vii) Date of annealing at other heat treatment of the chain and
other lifting tackle made under sub-rule (6) and by whom it was carried out.
(viu) Particulars of any defects found at any such thorough
examination or after annealing and affecting the safe working load, and of
the steps taken to remedy such defects.
TAMIL NADU FACTORIES RULES, 1950 [R. 55-A
(4A) Passage ways for cranes - (i) To provide access to rail
tracks of overhead travelling cranes suitable passage-ways of at least 50 cm.
(20 inches) width with toe boards and double hand rails 90 cm. (3 feet) high
shall be· provided alongside, and clear of the rail tracks of overhead
travelling cranes, such that no moving part of the crane can strike persons
�n the' ways, and the passage-way shall be at a lower level than the crane can
strike persons on the ways, and the passage-way shall be at a lower level
than the crane track itself. Safe access ladders shall be provided at suitable
intervals to afford access to these passage-ways, and from passage-ways to
the rail tracks.
1[(ii) The Chieflnspector may, for reasons to be specified in writ
ing, exempt any factory in respect of any overhead travelling crane from the
operation of any provisions of clause (i) subject to such conditions as he
may specify.}
(5) All rails on which a travelling crane moves and every track
on which the carriage of a transporter or runway moves, shall be of proper
size and adequate strength and have an even running surface and every
such rail or track shall be properly laid, adequately supported and properly
maintained.
(6) All chains, and lifting tackle, except a rope sling shall, unless
they have been subjected to such other heat treatment as may be approved
by the Chief Inspector, be effectively annealed under the supervision of a
competent person at the following intervals : -
(i) All chains, slings, rings, hooks, shackles and swivels used
in connection with molten metal or molten slag or when they are made of
12. 7 millimetres bar or smaller, once at least in every six months.
(ii) All other chains, rings, hooks, shackles and swivels in
general use, once at least in every twelve months :
Provided that chains and lifting tackle not in frequent use shall, sub
ject to the Chief Inspector's approval, be annealed only when necessary.
Particulars of such annealing shall be entered in a register prescribed under
sub-rule (4) which shall be kept available for inspection.
(7) Nothing in the foregoing sub-rule (6) shall apply to the
following classes of chains and lifting tackle : -
(i) Chains made of malleable cast iron.
' Sub. by G.O. Ms. No. 210, Labour and Employment, dated the 18th March,
1978.
R. 56] TAMIL NADU FACTORIES RULES. 1950
(ii) Plate link chains.
(iii) Chains, rings, hooks, shackles and swivels made of steel or
of any non-ferrous metals.
(iv) Pitched chains, working on sprocket or pocketed wheels.
(v) Rings, hooks, shackles and swivels permanently attached
to pitched chains, pulley blocks or weighing machines.
(vi) Hooks and swivels having screw threaded parts or ball
bearing or other case-hardened parts.
(vii) Socket shackles secured to wire ropes by white metal
capping.
(viii) Bordeaux connections.
Such chains and lifting tackles shall be thoroughly examined by a
competent person once at least in every twelve months and particulars en
tered in the register kept in accordance with sub-rule (4).
(8) All lifting machines, chains, ropes and lifting tackle, except a
fibre rope or fibre rope sling, which have been lengthened, altered or
repaired by welding or otherwise shall, before being again taken into use, be
adequately re-tested and re-examined by a competent person and a certifi
cate of such test and examination be obtained and -particulars entered in the
register kept in accordance with sub-rule ( 4 ).
(9) No person under 18 years of age and no person who is not
sufficiently competent and reliable shall be employed as driver of a lifting
machine whether driven by mechanical power or otherwise, or to give
signals to a driver.
Rules 56 1(56. Pressure Plant. - ( I ) Definition. - In this rule -
and 56-A pre
scribed under
sections 31( 2)
and 31 (3).
(h) · maximum permissible working pressure' is the maximum
pressure at which a pressure vessel or plant is permitted to be operated or
used under this rule and is determined by the technical requirements of the
process ;
(c) · plant ' means a system of piping that is connected to a
pressure vessel and is used to contain a gas vapour or liquid under pressure
greater than the atmospheric pressure, and includes the pressure vessel.;
I Sub. by G.O. Ms. No. 541 , Labour and Employment. dated the 13th June. 1975.
(a) ' design pressure ' means the maximum
pressure that a pressure vessel or plant is designed to
withstand safely when operating normally;
TAMIL NADU FACTORIES RULES, 1950 [R. 56
(d) ' pressure vessel ' means 1[a] vessel that may be used for
containing, storing, distributing, transferring, distilling, processing or other
wise handling any gas, vapour or liquid under pressure greater than the
atmospheric pressure and includes any pipeline fitting or other equipment
attached thereto or used in connection therewith ; and
2[(e) " notified person " means a person notified by the State
Government, for the purpose of this rule ;]
(2) Exceptions. - Nothing in this rule shall apply to -
(a) l[* * *]
(b) vessels made of ferrous materials having an internal operat
ing pressure not exceeding I kg./cm2 (15 1 bs/square inch);
(c) steam boiler, steam and feed pipes and their fittings coming
under the purview of Indian Boilers Act, 1923 (Central Act V of 1923) ;
(d) metal bottles or cylinders used for storage or transport of
compressed gases or liquified or dissolved gases, under pressure covered
by the Gas Cylinder Rules, t 940 framed under the Indian Explosives Act,
1884 (Central Act IV of 1884);
(e) vessels in which internal pressure is due solely to the static
head ofliquid ;
(f) vessels with a nominal water capacity not exceeding 500
litres connected in a water-pumping system containing air that is compressed
to serve as a cushion ;
(g) vessel for nuclear energy application ;
(h) refrigeration plant having a capacity of three tons or less of
refrigeration in 24 hours ; and
(i) working cylinders of steam engines or prime movers, feed
pumps and steam traps ; turbine castings ; compressor cylinders ; steam
separators or drivers ; steam strainers ; steam desuper heaters ; oil separa
tors; air receivers for fire sprinklers installations; air receivers of monotype
machines provided the maximum working pressure of the air receiver does
not exceed I .33kg.f/cm. (20 lbs./sq inch) and the capacity 84.95 litres (3 cu.ft);
air receivers of electrical circuit breakers; air receivers of electrical relays; air
vessels on pumps, pipe coils, accessories of instruments and appliances,
I Suli. for" an unfired ··. by G.O. Ms. No. 1523, Labour and Employment, dated the
10th July. 198.0.
2 Sub. by G.O. Ms. No. 2547, Labour, dated the 3rd December, 1985. ·
·' Cl. (a) omitted by G.O. Ms. No. 572, Labour, dated the 18th March, 1985.
R. 56] TAMIL NADU FACTORIES RULES, 1 9 5 0
such as cylinders and piston assemblies used for operating relays and inter
locking type of guards ; vessels with liquids subjected to static head only ;
and hydraulically operating cylinders other than any cylinder communicated
with an air loaded accumulator.
(3) Design and construction. - Every pressure vessel or plant
used in a factory -
(a) shall be properly designed on sound engineering practice ;
(b) shall be of good construction, sound material, adequate
strength and free from any patent defects ; and
(c) shall be properly maintained in a safe condition :
Provided that a pressure vessel or plant in respect of the design and
construction of which there is an Indian Standard or a standard of the coun
try of manufacture or any other law or regulation in force, shall be designed
and constructed in accordance with the said standard, law or regulation, as
the case may be and certificate thereof shall be obtained from the manu
facturer or from the 1[notified person] which shall be kept and produced on
demand by an Inspector.
(4) Safety devices. --Every pressure vessel shall be fitted with-
(a) a suitable safety valve or other effective pressure relieving
device of adequate capacity to ensure that the maximum permissible working
pressure of the pressure vessel shall not be exceeded. It shall be set lo
operate at a pressure not exceeding the maximum permissible working pres
sure and when more than one protective device is provided, only one of the
devices need be set to operate at the maximum permissible working pressure
and the additional device shall be set lo discharge at a pressure not more
than 5 per cent. in excess of the maximum permissible working pressure;
(b) a suitable pressure gauge with a dial range not less than
1 .5 times the maximum permissible working pressure, easily visible and
designed lo show at all times the correct internal pressure and marked with a
prominent red mark al the maximum permissible working pressure of the
pressure vessel ;
(c) a suitable nipple and globe valve connected for the exclu
sive purpose of attaching a test pressure gauge for checking the accuracy of
the pressure guage referred to in clause (b) of this sub-rule;
I Sub. for " competent person ''. by G.O. Ms. No. 2547. Labour. dated the 3rd
December. 1984.
TAMIL NADU FACTORIES RULES, 1950 [R. 5 6 .
(d) a suitable stop valve or valves by which the pressure ves
sel may be isolated from other pressure vessels or plant or source of supply
of pressure. Such a stop valve or valves shall be located as close to the
pressure vessel as possible and shall be easily accessible ; and
(e) a suitable drain cock or valve at the lowest part of the pres
sure vessel for the discharge of the liquid or other substances that may
collect in the pressure vessel :
Provided that it shall be sufficient for the purpose of this sub-rule if
the safety valve or pressure relieving device, the pressure gauge and the
stop valve are mounted on a pipeline immediately adjacent to the pressure
vessel and where there is a range of two or more similar pressure vessels
served by the same pressure lead, only one set of such mountings need be
fitted on the pressure lead immediately adjacent to the range of pressure
vessels, provided they cannot be isolated.
(5) Pressure reducing devices. - (a) Every pressure vessel
which is designed for a working pressure less than the pressure at the source
of supply, or less than the pressure which can be obtained in the pipe con
necting the pressure vessel with any other source of supply, shall be fitted
with a suitable pressure reducing valve or other suitable automatic device to
prevent the maximum permissible working pressure of the pressure vessel
. being exceeded ;
(b) To further protect the pressure vessel in the event of failure
of the reducing valve or device, at least one safety valve having a capacity
sufficient to release all the steam, vapour or gas without undue pressure rise
as determined by the pressure at the source of supply and the size of the
pipe connecting the source of supply, shall be fitted on the low pressure side
of the reducing valve.
(6) Pressure vessel or plant being taken into use.- (a) No
new pressure vessel or plant shall be taken into use in a factory after coming
into force of this rule unless it has been hydrostatically tested by a compe
tent person at a pressure at least 1 .3 times the design pressure, and no
pressure vessel or plant which has been previously used or has remained
isolated or idle for a period exceeding two months or which has undergone
· alterations or repairs shall be taken into use in a factory unless it has been
thoroughly examined by a '[notified person) externally, and internally if prac
ticable, and has been hydroslalically tested by the '[notified person] at a
I Sub. for " competent person ", by G.O. Ms. No. 2547. Labour, dated the 3rd
December. 1984.
pressure which shall be 1 . 5 times the maximum permissible working
pressure:
Provided, however, that the pressure vessel or plant which is so
designed and constructed that it cannot be safely filled with water or liquid
or is used in service even some traces of water cannot be tolerated. shall be
pneumatically tested at a pressure not less than the design pressure or the
maximum permissible working pressure as the case may be :
Provided further that the pressure vessel or plant which is lined with
glass shall be tested hydrostatically or pneumatically as required at a pres
sure not less than the design pressure or maximum permissible working
pressure as the case may be.
Design pressure shall be not less than the maximum permissible work
ing pressure and shall take into account the possible fluctuations of pres
sure during actual operation.
I
(b) No pressure vessel or plant shall be used in factory unless
there has obtained from the maker of the pressure vessel or plant or from the
1[notified person] a certificate specifying the design pressure or maximum
permissible working pressure thereof, and stating the nature of tests to which
the pressure vessel or plant and its fittings (if any) have been subjected, and
every pressure vessel or plant so used in a factory shall be marked so as to
enable it to be identified as to be the pressure vessel or plant to which the
certificate relates and the certificate shall be kept available for perusal by the
Inspector.
(c) No pressure vessel or plant shall be permitted to be
operated or used at a pressure higher than its design pressure or maximum
permissible working pressure as shown in the certificate.
(7) In service test and examinations. - Every pressure
vessel or plant in service shall be thoroughly examined by a 1[notified
person] -
(a) externally, once in every six months ;
(b) internally, once in every twelve months.
If by reason of the construction of a pressure vessel or plant, a thor
ough internal examination is not possible, this examination may be replaced
by a hydrostatic.:Jest which shall be carried out once in every two years:
I Sub. for " competent person ", by G.O. Ms. No. 2547. Labour, dated the 3rd
December. 1984.
R. 56] TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 (R. 56
Provided that for a pressure vessel or plant in continuous process
which cannot be frequently opened, the period of internal examination may
be extended to four years ;
(c) hydrostatically tested once in every four years ; and
(d) the hydrostatic test pressure to be carried out for the pur
pose of this rule shall be 1.25 times the design pressure or 1 .5 times the
maximum permissible working pressure whichever is less :
Provided that in respect of a. pressure vessel or plant with thin
walls such as sizing cylinder made of copper or any other non-ferrous metal,
periodic hydrostatic test may be dispensed with subject to the condition
that the requirements laid down in sub-rule (8) are fulfilled :
Provided further that when it is impracticable to carry out thorough
external examination of any pressure vessel or plant every six months as
required in clause (a) of this sub-rule, or if owing to its construction and use
a pressure vessel or plant cannot be hydrostatically tested as required in
clauses (d) and (c) of this sub-rule, a thorough external examination of the
pressure vessel or plant shall be carried out at least once in every period of
two years ; and at least once in every period of four years thorough syste
matic non-destructive test like ultrasonic test for thickness or other defects
of all parts the failure of which might lead to eventual rupture of the pressure
vessel or plant shall be carried out.
(8) Thin walled pressure vessel or plant. - (a) In respect of
any pressure vessel or plant of thin walls such as sizing cylinder made of
copper or any other non-ferrous metal the maximum permissible working
pressure shall be reduced at the rate of 5 per cent. of the original maximum
permissible working pressure for every year of its use after the first five
years and no such cylinder shall he allowed to continue to he used for more
than twenty years after it was first taken into use ;
(b) If any information as to the date of construction, thickness
of walls, or maximum permissible working pressure is not available, the age
of such pressure vessel or plant shall he determined by the 1[notified per
son] in consultation with the ChiefInspector from the other particulars avail
able with the manager ;
(c) Every new and second hand pressure vessel or plant of thin
walls to which repairs likely to affect its strength or safety have been carried
' Sub. for ·' competent person ''. by G.O. Ms. No. 2547. Labour. dated the 3rd
December. 1984.
R. 561 TAMIL NADU FACTORIES RULES, 1950
out shall be tested before use to al least 1 . 5 limes its maximum permissible
working pressure.
(9) 1(Report by notified person].-(a) If during any examination
any doubt arises as to the ability of the pressure vessel or plant to work
safely until the next prescribed examination, the 2[notified person] shall enter
in the prescribed register his observations, findings and conclusions with
other. relevant remarks with reasons and may authorise the pressure vessel
or plant to be used and kept in operation subject to a lowering of maximum
permissible working pressure, or to more frequent or special examination or
test, or subject to both of these conditions ;
(b) A report of the result of every examination or test carried
out shall be completed in the prescribed Form No. 8 and shall be signed by
the person making the examination or test, and shall be kept available for
perusal by the Inspector at all hours when the factory or any part thereof is
working;
(c) Where the report of any examination under this rule speci
fied any condition for securing the safe working of any pressure vessel or
plant, the pressure vessel or plant shall not be used unless the specified
condition is fulfilled ;
(d) The 2[notified person] making report of any examination
under this rule, shall within seven days of the completion of the examination
send to the Inspector a copy of the report in every case where the maximum
permissible working pressure is reduced or the examination shows that the
pressure vessel or plant or any part thereof cannot continue to be used with
safety unless certain repairs are carried out or unless any other safety mea
sure is taken.
(10) Application of other laws. - (a) The requirements of this
rule shall be in addition Lo and without any prejudice to and not in deroga
tion of the requirements of any other law in force ;
(b) Certificates or reports of any examination, or test of any pre
ssure vessel or plant to which sub-rules (7) to (9) do not apply, conducted or
required to be conducted under any other law in force and other relevant·
record relating to such pressure vessel or plant, shall be properly maintained
as required under the said law and shall be produced on demand by the
Inspector.
I Heading substituted, by G.O. Ms. No. 2547, Labour. dated the 3rd December.
1984.
1 Subs. for "competent person", ibid.
56-A. Water sealed gas holder. - ( I ) The expression - " gas
holder ··. means a water sealed gas holder which has a storage capacity of
not less than 1 4 1 . 5 cubic metres (5000 cu. ft).
(2) Every gas holder shall be of good construction, sound mate
rial, adequate strength and properly maintained.
(3) Where there is more than one gas holder in the factory every
gas holder shall be marked in a conspicuous position with a distinguishing
number or letter.
(4) Every gas holder shall be thoroughly examined externally by
a '[notified person] at least once in every period of 12 months.
(5) In the case of a gas holder of which any lift has been in use
for more than 10 years, the internal state of the sheeting shall, within one
year of the coming into force of this rule and thereafter at least once in every
period of four years, be examined by a '[notified person] by means of elec
tror or other accurate devices :
Provided that if the Chief Inspector is satisfied that such electronic or
other accurate devices are not available, he may permit the cutting of samples
from the crown and the sides of holder :
Provided, further, that if such inspection raises a doubt, an internal
visual examination shall be made.
(6) All possible steps shall be taken to prevent or minimise
ingress of impurities in the gas holder. ,·
(7) No gas holder shall be repaired or demolished except under
the direct supervision of a person who, by reason of his training and experi
ence and of his knowledge of the necessary precautions against risks of
explosion and of persons being overcome by gas, is competent to supervise
such work.
(8) (i) All sample discs cut under sub-rule (5) shall be kept readily
available for inspection.
(ii) A perrnaner t register duly signed by the occupier or man
ager shall be maintained gi . mg the following particulars, namely : -
(a) the distinguishing number or letter of the gas holder .
specified under sub-rule (3) and the particulars of manufacture relating to
the maker's name, date of manufacture, capacity, number of lifts and pres
sure thrown hy holder when full, of gas ;
(b) the dates �f examination carried out as required by sub·
rules (4) and (5) and by whom carried out ;
1 � . , ; , _ for " competent person ··. by G.O. Ms. No. 2547, Labour. dated the Jrd
December. 1984.
TAMIL NAl>IJ FACTORIES RULES, 1950 [R. 56-A
(c) the method of examination used ;
(d) date of painting and other similar particulars ;
(e) nature of repairs and name of persons carrying out such
repairs ; and
(f) other remarks, if any.
(iii) The results of examinations by a [notified person] carried out
under sub-rules (4) and (5) shall be in Form No. 8-A.
(iv) A copy of the report in Form No. 8-A shall be kept in the
register and both the register and the report shall be readily available for inspection
by an Inspector.
(9) The Inspector shall ensure that every gas holder is duly examined
periodically as required by sub-rules (4) and (5).
2 [ 56-B. Testing or Examination of Pressure Plant or Vessel. — (1) An
1Sub. fcr "competent person", by GO. Ms. No. 2547, L&E, dated 3rd December, 1984.
2Ins. by GO. Ms. No. 204, Labour and Employment (M-2), dated 23rd July, 2004.
5Subs.by GO. Ms. No. 109, L &E (M-2), dated the 10th September, 2008.
R 56-B] TAMIL NADU FACTORIES RULES, 1950
application duly filled in Form No. 8-B for the testing or examination of
pressure plant or vessel or water sealed gas holder shall be submitted to the respective
Deputy Chief Inspector of Factories 3[through online portal of Directorate
of Industrial Safety and Health].
4[(2) The fee payable for the examination and testing of pressure plant
or vessel or water sealed gas holder shall be as follows : —
(i) ₹800/-(Rupees eight hundred only) per plant or vessel
irrespective of its size or capacity, for the external examination ;
(ii) ₹2000/- (Rupees two thousand only) per plant or vessel
upto 4 kgf/sq.cm (g) for the Hydrostatic test ;
(iii) ₹4000/- (Rupees four thousand only) per plant or vessel
above 4 kgf/sq.cm (g) for the Hydrostatic test ;
(iv) ₹2000/-(Rupees two thousand only) per plant or vessel
irrespective of the size or capacity, for the internal
examination; and
(v) ₹8000/- (Rupees eight thousand only) per plant or vessel
irrespective of the size or capacity, for the non-destructive
ultrasonic thickness gauging test]
(4) The occupier shall apply for examination and testing of Pressure
Vessel or Plant alongwith the prescribed application and fee one month in
advance from the date on which the vessel or plant fall due for such examination
or test ]
(3) Every application under sub-rule (1) shall be accompanied 5[by a
treasury receipt or by a crossed demand draft drawn in any branch of a Nationalised
Bank in favour of the respective Deputy Chief Inspector of Factories] 6[or by
online payment through online portal of Directorate of Industrial Safety and
Health] evidencing payment of appropriate fee specified in sub-rule (2) ; and
3Subs. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January
4Subs. by GO. Ms. No. 132, L& E(M-2), dated the 28thSeptember,2018.
6Subs. by G.O. Ms. No. 15, Labour & Employment (M2), dated 31st January
R · U I e
prescr ibed
under sub
section 2 of
section 34.
57. Excessive weights. - ( I ) No man. woman or young person
shall, unaided by another person, lift. carry or move by hand or
on head, any material, article, tool or appliance exceeding the
maximum limit in weight set out in the following schedule : -
20
16
13]
'[SCHEDULE
Maximum weiglit of material, article, tool or applia11ce
K. Grams.
i 1(50]
30--
30
Persons
(c) Adolescent male
(d) Adolescent female
(e) Male child
(f) Female child
(a) Adult male
(b) Adult female
(2) No man, woman or young person shall engage, in conjunc
tion with others, in lifting, carrying or moving by hand or on head, any
material, article, tool, or appliance, if the weight thereof exceeds the lowest
weight fixed by the schedule to sub-rule ( I ) for any of the persons engaged,
multiplied by the number of the persons engaged.
R u l e s
prescribed
under sec
tion 28.
58. Protection of eyes. - Effective screens or suitable goggles
shall be provided for the protection of persons employed in
or in the immediate vicinity of the following processes
(a) The processes specified in Schedule I annexed hereto, being
processes which involve risk of injury to the eyes from particles or frag
ments thrown off in the course of the process.
(b) The processes specified in Schedule 1 1 annexed hereto,
being processes which involve risk of injury to the eyes by reason of expo
sure to excessive light 2[or infra-red or ultra-violet radiations.]
SCHEDULE I
I . The breaking, cutting, dressing or carving of bricks, stone, con
crete, slag or sim i lar materials by means of a hammer, a chisel, pick or similar
hand tool. or by means of a portable tool driven by mechanical power, and
the dry grinding of surfaces of any such materials by means of a wheel or
disc driven by mechanical power, wherein any of the foregoing cases, par
ticles or fragments are liable to he thrown off towards the face of the operator
in the course of the process.
I Amended by G.O. Ms. No. 564. Labour & Employment, dated the 4th August. 197::/.
2 Sub. by G.O. Ms. No. 368.- Labour. dated the 23rd February. 1985.
· ' I n s .by G.O. Ms. No. 1093. Lab. & Emp .. ( M - 1 1 ) . dated the 23rd December. 1976.
TAMIL NADU FACTORIES RULES, 1950 [R. 58
"R. 58]
2 The dry grinding of surfaces of metal by supplying them by hand
to a wheel, disc or hand driven by mechanical power, and of surfaces of
metal by t.ieans of a portable tool driven by mechanical power.
3. The dividing into separate parts of metal, bricks, stone, concrete
or similar materials by means of high speed of saw driven by mechanical
power or by means of an abrasive cutting off wheel or disc driven by
mechanical power.
4. The turning of metals, or articles of metal, where particles or
fragments are liable to be thrown off towards the fact of the operator in the
course of the· process.
5. Drilling by means of portable tools, where particles or fragments
are liable to be thrown off towards the face of the operator in the course of
the process.
6. The welding and cutting of metals by means of an electric, oxy
acetylene or similar process.
7. The hot fettling of steel castings by means of a flux injected burner
or air-torch, and the de-seaming of metal.
8. The fettling metal castings, involving the removal of metal,
including runners, gates and risers and the removal of any other material
during the course of such fettling.
9. The chipping of metal, and the chipping knocking out, cutting out
or cutting off cold rivets, bolts, nuts, lugs, pins, collars, or similar articles
from any structure or plant, or from part of any structure or plant, by means
of a hammer, chisel, punch or similar hand tool, or by means of a portable
tool driven by mechanical power.
10. The chipping or scurfing of paint, scale, slag rust or other corrosion
from the surface of metal and other hard materials by means of a hand tool
or by a portable tool driven by mechanical power.
1 1 . The breaking of scrap metal by means of a hammer or by means of
a tool driven by mechanical power.
12. The routing of metal, where particles or fragments are liable to be
thrown off towards the face of the operator in the course of the process.
13. Work with drop hammers and power hammers, used in either case
for the manufacture of forgings, and work by any person not working with
such hammers whose work is carried on in such circumstances and in such
a position that particles or fragments are liable to be thrown off towards his
face during work with drop hammers or power hammers.
TAMIL NADU FACTORIES RULES, 1950
TAMILNADU FACTORIES RULES, 1950 [R. 59
14. Work at a furnace where there is risk to the eyes from molten metal.
15. Pouring or skimming of molten metal.
16. Work involving risk to the eyes from hot sand being thrown off.
17. Truing or dressing of an abrasive wheel.
18. The handling in open vessels or manipulation of strong acids or
dangerous corrosive liquids or materials, and the operation, maintenance or
dismantling of plant or any part of plant, being plant or part of plant, which
contains or has contained such acids. liquids or materials, unless the plant
or part of plant has been so prepared (by isolation, reduction of pressure,
or otherwise), treated or designed and constructed as to prevent risk of
injury.
19. Any other process wherein there is a risk of injury to eyes from
particles or fragments thrown off during the course of the process.
1[SCHEDULE
(I) Welding or cutting of metals by means of an electrical, oxy
acetylene or similar process.
(2) All work on furnaces where there is risk of exposure to
excessive light or infra-red radiations.
(3) Process such as rolling, casting or forging of metals where there
is risk of exposure to excessive light or infra-red radiations.
(4) Any other process wherein there is a risk of injury to eyes from
exposure to excessive light or ultra-violet or infra-red radiations.]
59. Minimum dimensions of manholes. - Every chamber, tank, vat,
Rule pres- pipe, flue or other confined space, which persons may have
cribed under to enter and which may contain dangerous fumes to such
sub-section (6) an extent as to involve risk of the persons being overcome
of section 36. thereby, shall unless there is other effective means of egress,
be provided with a manhole which may be rectangular, oval or circular in
shape, and which shall -
(a) in the case of a rectangular or oval shape, be not less than
40.6 centimetres long and 30.5 centimetres wide;
(b) in the case of a circular shape, be not less than 40.6 centimetres
in diameter.
I Subs. by GO. Ms. No. 1093, Labour and Employment (M-11) dated 23-12-1976.
[R. 60] TAMIL NADU FACTORIES Ruu�s, 1950
60. Exemptfions.-The requirements of sub-section (4) of
. section 37 shall not apply to the following processes
E x e m P hons carried on in any factory :
under sub-sec-
t!OD (5) of sec- (a) The operation of repairing a water
t1on37. h d h l . Id' . sealed gas ol er by t e e ectnc we mg process
subject to the following conditions:
(i) The gas holder shall contain only the following gases
separately or mixed at a pressure greater than atmospheric pressure,
namely, town gas, coke-oven gas, producer gas, blast furnace gas
or gases other than air, used in their manufacture:
Provided that this exemption shall not' apply to any gas holder
containing acetylene or mixture of gases to which acetylene has
been added intentionally.
(ii) Welding shall only be done by the electric welding
process and shall be carried out by experienced operatives under
the constant supervision of a competent person.
(b) The operations of cutting or welding steel or wrought
iron gas mains and services by the application of heat, subject to
the following conditions :
(i) The main or service shall be situated in the open air,
I and it shall contain only the following gases, separately or mixed
· at a pressure greater than atmospheric pressure, namely, gas, coke
oven gas, producer gas, blast furnace gas or gases other than air,
. used in their manufacture ;
· (ii) the main or service shall not contain acetylene or any
gas or mixture of gases to which acetylene has been added inten
. tionally;
(iii) the operation shall be carried out by an experienced
. person or persons and at least two persons (including those carrying
out the operations) experienced in work on gas mains and over 1 8
years of age shall be present during the operation;
(iv) the site of the operation shall be free from any
inflammable or explosive gas or vapour;
(v) where acetylene gas is used as a source of heat in
connexion with an operation, it shall be compressed and contained
in a porous substance in a cylinder ; and
(vi) prior to the application of any flame to.the gas main
or service, this shall be pierced or drilled and the escaping gas
ignited.
(c) The operation of repairing an oil tank on any ship by
the electric wedling process, subject to the following conditions :-
(i) The only oil contained in the tank shall have a flash point of
not less than 150"B-( close test) and a certificate to this effect shall be
obtained from a competent analyst ;
(ii) the analyst's certificate shall be kept available for inspection
by an Inspector or by any person employed or working on the ship ;
(iii) the welding operation shall be carried out only on "the
exterior surface of the tank at a place ( a) which is free from oil or oil
leakage in inflammable quantities and (b) which is not less than
30.5 centimetre below the nearest part of the surface of the oil within the
tank; and
(iv) welding shall be done only by the electric welding' and shall
be carried out by experienced operatives under the constant supervision
of a.competent person.
1[61. Fire protection. -- (1) Processes, equipment, plant, etc.,
involving serious explosion and serious fire hazards. --
( a) All processes, storages, equipments, plants, etc., involving
serious explosion and flash fire hazards shall be located in segregated
building where the equipment shall be so arranged that only a minimum'
number of employees are exposed to such hazards at any one time.
(b) All industrial processes involving serious fire hazard should
be located in buildings or work places separated from one another by
walls of fire-resistant construction.
(c) Equipment and plant involving serious fire or flash fr."
hazard shall, wherever possible, be so constructed and installed that in
case of fire, they can be easily isolated,
( d) Ventilation ducts, pneumatic conveyors and similar equip
ment involving a serious fire risk should be provided with flame-arresting
or automatic fire extinguishing appliances -or fire resisting dampers
electrically interlocked with heat sensitive/smoke detectors and the air
conditioning plant system.
( e) In all workplaces having serious fire or flash fire hazards,
passages between machines, installations or piles of material should �eat
1Subs. by G.O. Ms. No. 1527, Labour, 20th July, 1988.
TJ\MIL NADu FACTORIES RtULES, 1950 ,
R.61] THE TAMIL NADU F
least 90 cm. wide. For storage piles, the clearance between the ceiling and
the top of the pile should not be less than 2m.
(2) Access for fire fighting. - (a) Buildings and Plants shall
be so laid out and roads, passage-ways, etc., so maintained as to permit
unobstructed access for fire fighting.
(b) Doors and window opening shall be located in suitable
positions on all external walls of the building to provide easy access to
the entire area within the building for fire fighting.
(3) 1[Protection against lightning.] -Protection from lighting
shall be provided for, -
(a) buildings in which explosive or highly flammable
substances are manufactured, used, handled or stored ;
(b) storage tanks containing oils, paints or other flammable
liquids;
( c) grain elevators ;
( d) buildings, tall chimneys or stacks where flammable gases,
fumes, dust or lint are likely to be present ; and
( e) sub-section buildings and out-door transformers and
switch yards.
( 4) Precautions against ignition. - Wherever there is danger
of fire or explosion from accumulation of flammable or explosive
substances in air : -
(a) all electrical apparatus shall either be excluded from the
area of risk or they shall be of such construction and so installed and
maintained as to prevent the danger of there being a source of ignition ;
(b) effective measures shall be adopted for prevention of
accumulation of static charges to a dangerous extent ;
( c) workers shall were shoes without iron or steel nails or any
other exposed ferrous materials which is likely to cause sparks by friction;
( d) smoking, lighting or carrying of matches, lighters or
smoking materials shall be prohibited ;
I Subs. for" Protection again! hghting ", by GO. Ms. No 121, Labour & Employment (M-2),
dated 3 lstJuly, 2012.
ACTORlES RULES, 1950
TAM� NADu FACTORIES RuLES, 1950 IR. 61
( e) transmission belts with iron fasteners shall not be.used; �d
(f) all otherprecautions as are reasonablypractica?le, shall be
taken by (sic) prevent initiation of ignition from all other possible so�rces
such as open flames, frictional sparks overheated surfac�s of machinery
or plant, chemical or physical chemical reaction and radiant heat.
(5) Spontaneous ignition. -- Where materials are likely to induce
spontaneous ignition, care shall be taken to avoid formation of air pocket
. and to ensure adequate yentilation. _!b.e material susceptible to spontane
ous ignition should J;>e stored in -dfy condition and should be in heaps of
such capacity and separated by such passage which will prevent fire. The
materials susceptible to ignition and stored in the open shall be at a
distance not less-than 10 metres away from process or storage buildings.
( 6) Cylinders containing compressed gas. -- Cylinders containing
compressed gas may only be stored in open if they are protected against
excessive variation of temperature, direct rays of sun, or continuous
dampness. Such cylinders shall never be stored near highly flammable
substances, furnaces or hot process. The room where such cylinders are
stored shall have adequate ventilation.
(7) Storage of flammable liquids. -- (a) The quantity of flam
mable liquids in any work room shall be the minimum required for the
process or processes carried on in such room. Flammable liquids shall be
stored in suitable containers with close fitting covers : '
Provided that not more than 20 litres of flammable liquids having
a flash point of 21 °C or less shall be kept or stored in any work room.
(b) Flammable liquids shall be stored in closed containers and
in limited quantities in well ventilated rooms of fire resisting construction
which are isolated from the remainder of the building by fire walls and self
closing fire doors.
( c) Large quantities of such liquids shall be stored in isolated
adequately ventilated building of fire resisting construction or in storage
tanks, preferably underground and at a distance from any building as
required in the Petroleum Rules, 1976.
( d) Effective steps shall be taken to prevent leakage of such
liquids into basements, sums or drains and to confine anyescaping liqilld
within safe limit. -, ,
[R.61 '
TAMIL NADu FACTORIES RuLES, 1950
(8) Accumulation of flammable dust, gas, fume or vapour in air
, · or flammable material on the floors. -- ( a) Effective steps shall be taken
for removal or prevention' of the accumulation in the air of flammable
dust, gas, fume or vapour to an extent which is likely to be dangerous.
(b) N9 waste material of a flammable nature shall be permitted
to accumulate on· the floors and shall be removed atleast one in a day or
shift, and more often, when possible. Such materials shall be placed in
suitable metal containers with covers wherever possible.
(9) Fire exists. -- (a) in this sub-paragraph=
(i) "Horizontal exit" means an arrangement which allows
alternative egress from a floor area to another floor at or near the same
level in an adjoining building or an adjoining part of the ,same building
with adequate separation ; and
(ii) "travel distance" means the distance an occupant has to
.travel to reach an exit. -
(b) An exit may be a doorway, corridor, passageway to an
external stairway or to a verandah or to an internal stairway segregated
from the rest of building by fire resisting walls which shall provide
continuous and protected means of egress to the exterior of a building or
to an exterior open space. An exit may also include a, horizontal exit
leading to an adjoining building a� the same level.
( c) Lifts, escalators and revolving doors shall not be considered
as exits for the purp�f this sub-paragraph.
( d) In every room of a factory exits sufficient to permit safe
escape of the occupants in case of fire or other emergency shall be
provided which shall be free of any obstruction.
( e) The exits shall be clearly visible and suitably illuminated
with suitable arrangement, whatever artificial lighting is to be adopted for
this purpose, to maintain the required illumination in case of f�ilure of the
normal source of electric supply.
(f) The exits shall be marked in a language understood by the _
majority of the workers. -.-
(g) Iron rung ladders or spiral staircases shall not be used as exit
staircases.
(h) Fire resisting doors or roller shutters shall be provided at
appropriate places along the escape routes to prevent spread of fire and
smoke, particularly at the entrance of lifts or stairs where funnel or flue
effect may be created inducing an upward spread of fire. 1
(i) All exits shall provide continuous means of egress to the
exterior of a building or to an exterior open space leading to a street.
G) Exits shall be so located that the travel distance to reach
atleast one of them on the floor shall not exceed 30 metres.
(k) In case of those factories where high hazard materials are
stored or used, the travel distance to the exit shall not exceed 22.5 metres
and there shall be atleast two ways of escape from every room, however
small, except toilet rooms, so located that the points of access thereto are
out of or suitably shielded from areas of high hazard.
(1) Wher�ver more than one exit is required for any room space
or floor, exits shall-be placed as remote from each other as possible and
shall be arranged to provide direct access in separate directions from any
point in the area served.
(m) The unit of exit width used to measure capacity of any exit
shall be_5Q cm. A clear width of25 cm. shall be counted as an additional
half unit. Clear width ofless than 25 cm. shall not be counted for exit width.
(n) Occupants per unit width shall be 50 for stairs and 75 for
doors.
( o) For determining the exits required, the occupant load shall
be reckoned on the basis of actual number of occupants within any floor
area or 10 square metr� per person, whichever is more. -
(p) There shall not be less than two exits serving every floor
area above and below the ground floor, and atleast one of them shall be
an internal enclosed stairway.
( q) For every building or structure used for storage only, and
every section thereof considered separately, shall have access to atleast
one exit so arranged and located as to provide a suitable means of escape
for any person employed therein and in any such room wherein more than
ten persons may be normally present, atleast two separate means of exit
shall be available, �s remote from each other as practicable.
TAMIL NADu Facrosrss RuLES, 1950 R.61] ·�
(r) Every storage area shall have access to atleast one means of
exit which can be readily opened.
(s) Every exit doorway shall open into an enclosed stairway, a
horizontal exit on a corridor or passage way providing continuous and
protected means of egress.
(u) Exit doorways shall open outwards, that is, away from the
room but shall not obstruct the travel along any exit. No door when
opened, shall reduce the required width of stairway or landing to less than
90 cm. Overhead or sliding doors shall not be installed for this purpose.
(v) An exit door shall not open immediately upon a flight of
stairs. A landing atleast 1.5 m. x 1.5 m. in size shall be provided in the
stairway at each doorway. The level of landing shall be the same as that of
the floor which it serves.
(w) The exit doorways shall be openable from the- si_d� which
they serve without the use of a key.
(x) Exit corridors and passage ways shall be of a width not less
than the aggregate required width of exit doorways leading from there in
the direction of travel to the exterior.
(y) Where stairways discharge through corridors and passage
ways, the height of the corridors and passage ways shall not be less than
2.4metres.
( aa) A staircase shall not be arranged round a lift shaft unless
the latter is totally enclosed by a material having a fire resistance rating
not lower than that of the type of construction of the farmer. '
(bb) Hallow combustible construction shall not be permitted . .
( cc) The minimum width of an internal staircase shall be 100
ems.
( dd) The minimum width of treads without nosing shall be 25
cm. for an internal staircase. The treads shall be constructed and main
tained in a manner to prevent, slipping.
[R.61 TAMIL NADu FACTORIES Rmas, 1950
(t) No exit doorway shall be less than 100 cm. in permitted
(sic).
ee) The maximum height of a risor shall be 19 cm. and the
number of risors shall be limited to 12 per flight.
/
(ff) Hand rails shall be provided with a minimum height of 100
cm. and shall be firmly supported.
(gg) The use of spiral staircase shall be llinited to low occupant
load and to a building of height of 9 metres, unless they are connected to
platform such as balconies and terraces to allow escapees to pause. A
spiral staircase shall be not less than 300 cm. in diameter and have
adequate head room.
(hh) The width of a horizontal exit shall be same as for the exit
/oorways.
(ii) The horizontal exit shall be equipped with atleast one fire
door of self closing type.
(ij) The floor area on the opposite or refuge side of a horizontal
exit shall be sufficient to accommodate occupants of the floor areas
served, allowing not less..than 0.3 square metre per person. The refuge
�hall be provided with exits adequate to meet the requirements of this
sub-rule. Atleast one of the exits shall lead directly to the exterior or
street.
(kk) Where there is difference in level between connected
areas for horizontal exit, rams not more than 1 in 8 slope shall be provided.
For this purpose steps shall not be used.
(II) Doors in horizontal exits shall be openable at all times.
(mm) Ramps with a slope of not more than 1 in 10 may be
substituted for the 'requirements of staircase. For all slopes exceeding 1 in
10 and wherever the use is such as to involve danger of slipping, the ramp,
shall be surfaced with non-slipping materials.
( nn) In any building not provided with automatic fire alarm a
manual fire alarm system shall be provided if the total capacity of the
building is over 500 persons, or if more than 25 persons are employed
above or below the ground floor, except that no manual fire alarm shall
be required in one-storey buildings where the entire area is undivided and
all parts thereof are clearly visible to all occupants.
(10) First-aid fire-fighting arrangements. -- ( a) In every factory
there shall be provided and maintained adequate and suitable fire fighting
TAMIL NADu FAcroRIFS RuLES, 1950 : R:61]
(
first-aid fire fighting equipment in this rule.
1((b) The types of first-aid fire fighting equipment to be
provided shall be determined by considering the different types of fire risks
which are classified as follows : -
(i) Class ' A ' Fire - Fire involving solid combustible
materials of organic nature such as wood, paper, etc.,
where the cooling effect of water is essential for
extinction of fire.
1. LIGHT HAZARD OCCUPANCIES.
Abrasive Manufacturing Premises.
2 Aerated Water Factories.
3 Agarbatti Manufacturing.
4 Aluminium, Zinc and Copper Factories.
5 Analiytical and/or Quality Control Laboratories.
6 Asbestos Steam Packing and Lagging Manufactories.
7 Battery Charging/Service Station.
8 Battery Manufactories.
9 Breweries.
10 Brick Works.
1 1 CanningFactories.
12 Cardamom Factories
13 Cement Factories and/or Asbestos Products Manufacturing.
14 Ceramic Factories and Crockery and Stoneware Pipe
Manufacturing.
15 Cinema Theatres (including Preview Theatres).
16 Clay works.
I 7 Clock and Watch Manufacturing.
1 8 Clubs.
I Subs. by GO Ms No 121, Labour& Employment (M-2), dated 31st July, 2012
THE TAMIL NADU FACTORIES RULES, 1950
equipment for fighting fires in the early stages, those being referred to as
THE TAMIL NADU FACTORIES RULES, 1950
19 Coffee Curing an Roasting Premises.
20 Computer installations (Main Frame).
21 Condensed Milk Factories, Milk Pasteurising Plant and Dairies.
22 Confectionery Manufacturing.
23 Dwellings.
24 Educational and Research Institutes.
25 Electric Generating Houses (Rydel).
26 Electric Lamps (Incandescent and Fluorescent) and TV Picture Tube
Manufacturing.
27 Electric Sub-Station Distribution Station.
28 Electroplating Works.
29 Electronic and/or Computer Equipments Assemble and
Manufactures.
3 0 Empty Containers Storage Yard.
I
3 1 Engineering Workshops.
3 2 Fruits and Vegetables Dehydrating/Drying Factories.
33 Fruit Products and Condiment Factories.
34 Glass and Glass Fibre Manufacturing.
35 Godowns and Warehouses Storing non-combustible Goods.
3 6 Green Houses.
3 7 Gold Thread Factories/Gliding Factories.
3 8 Gum and/or Glue and Geletine Manufacturing.
39 Hospitals including X-ray and other Diagnostic Clinics.
40 Ice Candy and Ice-cream Manufacturing.
41 Ice Factories.
42 Ink ( excluding Printing Ink) Factories.
43 Laundries.
44 Libraries.
45 Mica Products Manufacturing.
46 Office Premises.
47 Places of Worship.
48 Pottery Works.
49 Poultry Farms.
50 Residential Hotels, Cafes and Restaurants.
51 Salt Crushing Factories and Refineries.
52 Stables.
53 Steel Plants ( other than Gas based).
54 Sugar Candy Manufacturing.
55 Sugar Factories and Refineries.
56 Tea Blending and Tea Packing Factories
57 Umbrella Assembling Factories.
58 Vermicelli Factories.
59 Water Treatment/Water Filtration Plants and Water Pump House.
2. ORDJ[NARY HAZARD OCCUPANCJ[JES.
Airport and other Transportation Terminal Building.
2 Areca Nut Slicing and/or Betel Nut Factories.
3 Atta and Cereal Grinding.
4 Bakeries.
5 Beedi Factories.
6 Biscuit Factories.
7 Bobbin Factories.
8 Book Binder, Envelopes and Paper Bag Manufacturers.
9 Bulk Storage.
10 Cable Manufacturing.
1 1 Camphor Boiling.
THE TAMIL NADU FACTORIES RULES, 1950
12 Candle Works.
13 Carbon Paper/Typewriter Ribbon Manufacturers.
14 Cardboard Box Manufacturing.
15 Carpenters, Wood Wool and Furniture Manufacturers.
16 Carpet and Drugget Factories.
17 Cashewnut Factories.
1 8 Chemical Manufacturing.
19 Cigar and Cigarette Factories.
20 Coffee Grinding Premises.
2 1 Coir Factories.
22 Coir Carpets, Rugs and Tobacco, Hides and Skin Presses.
23 Cold Storage Premises.
24 Cork Products Manufacturing.
25 Dry Cleaning, Dyeing and Laundries.
26 Electric Generating Stations (Other than Rydel).
27 Enamelware Factories.
2 8 Filter and Wax Paper Manufacturing.
29 Flour Mills.
30 Garages.
3 1 Garment Makers.
3 2 Ghee Factories ( other than vegetable).
3 3 Godowns and Warehouses (others).
34 Grain and/or Seeds Disintegrating and/or Crushing Factories.
3 5 Grease Manufacturing.
36 Hat and Topee Factories.
3 7 Hosiery, Lace, Embroidery and Thread Factories.
3 8 Incandescent Gas Mantle Manufacturers.
THE TAMILNADU FACTORIES RULES, 1950
3 9 Industrial gas manufacturing including halogenated hydrocarbon
gases.
40 Linoleum Factories.
41 Man-made Yard/Fibre Manufacturing (ExceptAcrylic).
42 Manure and Fertilizer Works (Blending, mixing and granulating
only).
43 Mercantile Occupancies (Departmental Stores, Shopping
Complexes of Malls).
44 Mineral Oil Blending and Processing.
45 Museums.
46 Oil and Leather Cloth Factories.
4 7 Oil Terminals/Depots other than those categorised under high
hazard A
48 Oxygen Plants.
49 Plywood Manufacturing/Wood Veneering Factories.
5 0 Paper and Cardboard Mills.
5 1 Piers, wharves, dockyards.
52 Plastic Goods Manufacturing.
5 3 Printing Press Premises.
54 Pulverising and Crushing Mills.
5 5 Rice Mills.
5 6 Rope Works.
5 7 Rubber Goods Manufacturing.
5 8 Rubber Tyres and Tubes Manufacturing.
59 Shellac Factories.
60 Shopping Complexes (underground).
6 1 Silk filatures and cocoon stores.
THE TAMIL NADU FACTORIES RULES, 1950
officers
Typewritten text
62 Spray Painting
63 Soaps and Glycerine Factories.
64 Starch Factories.
65 Steel Plants (Gas Based).
66 Tanneries/Leather Goods Manufacturers.
67 Tank farms other than those categories under high hazard A.
68 Textile Mills.
69 Tea Factories.
70 Telephone Exchanges.
71 Theatres and Auditoriums.
72 Tobacco (Chewing) and pan-masala making.
73 Tobacco Grinding and Crushing.
74 Tobacco Re-drying Factories.
75 Woollen Mills.
3. IDGH HAZARD OCCUPANCIES.
Sub-Category-A :
Aircraft Hangers.
2 Aluminium/Magnesium Powder Plants.
3 Bituminised Paper and/or Hessian Cloth Manufacturing including
Tar Felt Manufacturing.
4 Cotton Waste Factories.
5 Coal and/or Coke and/or Charcoal Ball Briquettes Manufacturing
6 Celluloid goods manufacturing.
7 Cigarette filter manufacturing.
8 Cinema films and T.V. production studios.
9 Collieries.
10 Cotton Seed Cleaning or De-lining Factories.
11 Distilleries.
THE TAMIL NADU FACTORIES RULES, l 950
I
12 Duplicating and Stencil Paper Manufacturing.
1 3 Fire-Works Manufacturing.
14 Foamed Plastics Manufacturing and/or Converting Plants.
15 Grass Hay, Fodder and Bhoosa ( chaff).
16 Pressing Factories.
17 Jute Mills and Jute Presses.
1 8 LPG Bottling Plants (Mini)*.
(* Bottling plants having total inventory not exceeding 100 Metric
Ton of Liquefied Petroleum Gas and also bottling a total quantity
of not exceeding 20 Metric Ton of LPG per shift of 8 hours.)
19 Match Factories.
20 Man Made Fibres (Acrylic fibres/Yarn making).
21 Mattress and Pillow Making.
22 Metal or Tin Printers (where more than 50% of floor area is
occupied as Engineering Workshop.this may be taken as Ordinary
Hazard Risk).
23 Oil Mills.
24 Oil Extraction Plants (other than those forming part of ghee
factories and oil refining factories).
25 Oil Terminals/Depots handling flammable liquids having flash
point of 32°C and below.
26 Paints and Varnish Factories.
2 7 Printing Ink Manufacturlng.
28 Saw Mills.
2 9 Sponge Iron Plants.
30 Surgical Cotton Manufacturers.
3 1 Tank Farms storing flammable liquids having flash point of32°C
and below.
32 Tarpaulin and Canvas Proofing Factories.
3 3 Turpentine and Rosin Distilleries.
34 Tyre Retreading and Resoling Factories.
THE TAMILNADU FACTORIES RULES, 1950
Sub-Category-B
1 Ammonia and Urea Synthesis Plants.
2 CNG Compressing and Bottling Plant.
3 Explosive Factories.
4 LPG Bottling Plants ( other than Mini).
5 Petrochemical Plants.
6 Petroleum Refineries.
· (ii) Class ' B ' Fire - Fire involving flammable liquids or
liquefiable solids or the like where a blanketing effect
is essential.
(iii) Class ' C ' Fire - Fire involving flammable gases under
pressure including liquefied gases, where it is necessary
to inhibit the burning gas at fast rate with an inert gas,
powder or vaporising liquid for extinguishment.
(iv) Class ' D ' Fire- Fire involving combustible metals, such
as magnesium, aluminium, zinc, sodium, potassium, etc.,
when the burring metal are reactive to water and water
containing agents and in certain cases carbon di-oxide,
halogenated hydrocarbons and ordinary dry powders. This
type of fire requires special media and techniques to
extinguish.
(c) The number and types of first-aid fire fighting equipment
to be provided shall be as per Bureau oflndian Standards recommendations
for installation of fire extinguishers given in Annexure B ofIS 2190 : 1992.
The types are detailed in Schedule-I.)
(d) The first-aid fire fighting equipment shall conform to the
relevant Indian Standards.
(e) As far as possible the first-aid fire fighting equipment
shall all be similar in shape and appearance and shall have the same method
operation.
(t) All first-aid fire fighting equipment shall be placed in a
conspicuous position and shall be readily and easily accessible for
immediate use. Generally, these equipment shall be placed as near as
possible to the exits or stair landing or normal routes of escape.
THE TAMIL NADU FACTORIES RULES, 1950
(g) All water buckets and bucket pwnp type extinguishers shall
be filled with clean water. All sand buckets shall be filled with clean, dry
and fine sand.
(h) All other extinguishers shall be charged appropriately in
accordance with the instructions of the manufacturer.
(i) Each first-aid fire-fighting equipment shall be allotted a
serial number by which it shall be referred to in the records.The following
details shall be painted with white paint on the body of each equipment :
(I) Serial number;
(2) Date oflast refilling ; and
(3) Date of last inspection.
G) First-aid fire fighting equipment shall be placed on
platforms or in cabinets in such a way that their bottom is 750 mm. above
the floor level. Fire buckets shall be placed on hooks attached to a suitable
stand or valve in such a way that their bottom is 720 mm. above the floor
level. Such equipment if placed outside the building, shall be under sheds
or covers.
(k) All extinguishers shall be thoroughly cleaned and re
charged immediately after discharge. Sufficient refill material shall be kept
readily available for this purpose at all time.
(I) All first-aid fire-fighting equipment shall be subjected to
routine maintenance, inspection and testing to be carried out by properly
trained persons. Periodicity of the routine maintenance, inspection and test
shall conform to the relevant Indian Standards.
( 1 1 ) Other fire-fighting arrangements. - '[(a) In every factory,
adequate provision for water supply for fire-fighting shall be made. Water
for the hydrant service shall be stored in an easily accessible surface or
underground lined reservoir or above ground tanks of steel, concrete or
masonry. The effective capacity of the reservoir above the lower water level
(a point at least three times the diameter of the suction pipe above the
draw-off points) or above the top of the pump casing (in case of flooded
suction) if the same is higher than the low water level, for various classes
of occupancies and size of hydrant installations shall be as indicated in the
Table below : -
'Subs. by GO. Ms. No. 121, Labour & Employment (M-2), dated 31st July, 2012.
THE TAMIL NADU FACTORIES RULES, 1950
THE TABLE
SI.No. Nature of Risk
(1) (2)
Light Hazard
2 Ordinary Hazard
3 High Hazard A
4 High Hazard B
Capacity of Static Storage Exclusively
Reserved for Hydrant Service.
(3)
Not less than I hours aggregate pumping
capacity with a minimum of 1,35,000 litres.
Not less than 2 hours aggregate pumping
capacity.
Not less than 3 hours aggregate pumping
capacity.
Not less than 4 hours aggregate pumping
capacity.
Note : 1. - The Capacity of the reservoir for ordinary and high
hazard class occupancies may be reduced by the quantum of inflow
(of one hour in case of ordinary hazard. 90 minutes in case of high
hazard A arid two hours in case of high hazard B occupancies) from a
reliable source (other than town's main) having prior approval of the
committee, but in no case shall the reservoir capacity be less than 70% of
that mentioned above.
Note: 2. - In case of light hazard class occupancies, the minimum
capacity of the reservoir shall be increased to 2,25,000 litres, if the highest
floor of the building is more than 15m. above the surrounding ground
level.).
(b) Each trailer pump shall be provided with equipment as per
Schedule II appended to this paragraph. Such equipment shall conform to
the relevant Indian Standard.
( c) Trailer pumps shall be housed in a separate shed or sheds
which shall be sited close to a principal source of water supplies in the
vicinity of the main risks of the factory.
(d) In factories where the area is such as cannot be
reached by man-hauling of trailer pumps within reasonable time
vehicles with towing attachment shall be provided at the scale of one for
every four trailer pumps with a minimum of one such vehicle kept available
at all times. ,
THE TAMIL NADU FACTORIES RULES, 1950
1 [ ( e) The hydrant system should be distributed round the factory
with due regard to potential fire risks at the factory. Where piped supply
is provided, the size of the main shall not be less than 15 cmdiameter and
it shall be capable of supplying a minimum of 4,500 litres per minute at a
pressure of not less than 7 kilograms per square cm. in case of light hazard
occupancies. In case of high hazard area, the water pressure should be 10
kg. per square centimetre.
A certificate of completion from the installing engineer stating the
pressure test to which the installation has been subjected and giving the
dates from which it is in complete working order should also be submitted
at the office of the inspector of Factories.],
(t) All trailer pumps including the equipment provided
with them and the vehicles for towing them shall be maintained in
good condition and subjected to periodical inspection and testing as
required.
(12) Personnel in-charge of equipment and for fire fighting,
fire drills, etc. - (a) The first-aid and other fire fighting equipment to
be provided as required in sub-paragraph (10) and ( 1 1 ) shall be in-charge
of a trained responsible person. ·
(b) Sufficient number of persons shall be trained in the proper
handling of fire fighting equipment as referred to in clause (a) and their
use against the types of fire for which they are intended to ensure that
adequate number of persons are available for fire fighting both by means
of first-aid fire fighting equipment and others. Such persons shall be
provided with clothing and equipment including helmets, belts and boots,
preferably gumboots. Wherever vehicles with towing attachment are to be
provided as required in clause (d) of sub-paragraph ( 1 1 ) sufficient number
of persons shall be trained in driving these vehicles to ensure that trained
persons are available for driving them whenever the need arises.
( c) Fire fighting drills shall be held as often as necessary and
at least once in every period of two months.
( 13) Automatic sprinkler and fire hydrants shall be in addition and
not in substitution of the requirements in sub-paragraphs (I 0) and ( l l ).
I Subs. by GO. Ms. No. 121, Labour & Employment (M-2), dated 3 JstJuly, 2012.
THE TAMIL NADU FACTORIES RULES, 1950
14) If the Chief Inspector is satisfied in respect of any factory
or any part of the factory that owing to the exceptional circumstances such
as inadequacy of water supply or infrequency of the manufacturing process
or for any other reason, to be recorded in writing, all or any of the require
ments of the rules are impracticable or not necessary for the protection
of workers, he may by order in writing (which he may at his discretion
revoke) exempt such factory or part of the factory from all or any of the
provisione of the rules subject to conditions as he may by such order
prescribe.
1 (( 15) Plan of fire-fighting installations showing the entire
,ompound, whole buildings therein, within their doors and window
openings, boundary walls, etc., should be submitted to the office of the
Inspector of Factories, the State Fire Directorate and the local authority.]
2(SCHEDULE-I
First-aid fire fighting equipments
( 1 ) The different types of fire and first-aid fire fighting equipment
suitable for use on them are as under :
Class of fire
Class ' A ' Fires
Class ' 8 ' Fires
Class ' C ' Fires
Suitable type of Appliance
Water expelling type extinguishers.
Foam, dry powder, vapourising liquid and carbon di
oxide extinguishers.
Dry powder, vaporising liquid and carbon di-oxide
extinguishers.
Note. - (I) Where energised electrical equipment is involved in a
fire, non-conductivity of the extinguishing media is of utmost importance,
and only extinguishers expelling dry powder, carbon di-oxide (without
metal horn) or vaporising liquids should be used. Once the electrical
equipment is de-energised, extinguishers suitable for the class of fire risk
\wolved can be used safely.
(2) Where cleanliness and contamination of sensitive electrical
equipment are of importance or where the sensitivity of the control
instruments or electronic equipment and systems are likely to be affected.
only carbon di-oxide or vaporising liquid type extinguishers should be used
• Added by GO. Ms. No. 12L Labour & Employment (M-2), dated 3lstJuly, 2012.
'Existing Schedule-I, substituted by G.O. Ms. No. 121, Labour & Employment (M-2), date,
31st July, 2012.
THE TAMIL NADU FACTORIES RULES, 1950
(
(3) For fires involving polar solvents and other water miscible
flammable liquids, dry powder type or mechanical foam extinguisher with
alcohol-resistant foam should be used.]
SCHEDULE II
Equipment to be Provided with Trailer Pump.
For light trailer pump of a capacity of 680 litres/minute.
Armoured suction hose of 9 metres length, with wrenches.
Metal suction strainer.
1 Basket strainer.
Two-way suction collecting-head.
I Suction adapter.
I O Unlined or rubber lined 70 mm. delivery hose of 25 metres length
complete with quick-release couplings.
Dividing breaching-piece.
2 Branch-piece with 15 mm. nozzles.
Diffuser nozzle.
Standpipe with blank cap.
Hydrant key.
4 Collapsible canvas buckets.
I Fire hook (preventor) with cutting edge.
25 mm. manila rope of 30 metres length.
Extension ladder of9 metres length (where necessary).
Heavy axe.
Spade.
Pick axe.
Crowbar.
Saw.
Hurricane lamp.
Electric torch.
Pair rubber gloves.
For large trailer pump of capacity of 1800 litres/minute.
I Armoured suction hose of 9 metres length with wrenches.
I Metal strainer.
Basket strainer.
THE TAMIL NADU FACTORIES RULES, 1950
Three-way suction, collecting head.
Suction adapter.
14 Unlined or rubber lined 70 mm. delivery hose of 25 metres length
complete with quick-release couplings.
Dividing breaching-piece.
I Collecting breaching-piece.
4 Branch pipes with one 25 mm., two 20 mm. and one diffuser nozzles.
2 Standpipe with blank caps.
2 Hydrant keys.
6 Collapsible canvas buckets.
Coiling hook (preventor) with cutting edge.
50 mm. manila rope of 30 mm. metres length.
Extension ladder of9 metres length (where necessary).
Heavy axe.
Spade.
Pick-axe.
Crowbar.
Saw.
Hurricane lamp.
I" Electric torch.
Pair rubber gloves.
Explanation. - If it appears to the Chieflnspector of Factories that
in any factory the. provision of breathing apparatus is necessary he may by
an order in writing require the occupier to provide suitable breathing
14'tpl)'ttfataiih addition to the equipment for light trailer pump or large trailer
pump as the case may be}.
61-A. Safety belts. - Where any person is required or allowed to
work at a place from which he may be liable to fall through a distance of
more than 1[two metres}, he shall be provided with a safety belt with leather
shoulder straps of not less than 1[five centimetres] in width and a ' D ' ring
at the back for fastening a rope, the other end of which shall be securely
tied or hooked to some suitable rigid fixture. The safety belt so provided
shall be tested and examined thoroughly by a competent person at least
once in six months and a certificate with regard to its suitability obtained
from the said competent person and entered in a register, which shall be
produced before the Inspector on demand.
I Subs. by GO. Ms. No. 1074, dated the 14th September, 1978.
THE TAMIL NADU FACTORIES RULES, 1950
R.61-B] TAMILNADU FACTORIES RULES, 1950
2[61-AA. Safety officers. - ***)
2(61-B. Ovens and driers. - (1) Application. - This rule shall apply
to ovens and driers, except those used in laboratories or kitchens of any
establishment and those which have a capacity below 325 litres.
(2) Definition. - For the purpose of this rule, oven or drier means
any enclosed structure, receptacle, compartment or.box which is used for
baking, drying or otherwise processing of any article or substance at a
temperature higher than the ambient temperature of the air in the room or
space in which the oven or drier is situated and in which a flammable or
explosive mixture of air and a flammable substance is likely to be evolved
within the enclosed structure, receptacle, compartment or box or part thereof
on account of the article or substance which is baked, dried or otherwise
processed within it.
(3) Separate electrical connection. - Electrical power supplied to
every oven or drier shall be by means of separate circuit provided with an
isolation switch.
(4) Designs, construction, examination and testing. - (a) Every
oven or drier shall be properly designed on sound engineering practice and
be of good construction, sound materials and adequate strength, free from
any patent defects and safe if properly used.
(b) No oven or drier shall be taken into use in a factory for the
first time unless a competent person has thoroughly examined all its parts
and carried out the tests as are required to establish that the necessary safe
systems and controls provided for safety in operation for the process for
which it is to be used and a certificate of such examination and tests signed
by that competent person has been obtained and is kept available for
inspection.
(c) All parts of an oven or drier which has undergone any
alteration or repair which has the effect of modifying any of the design
characteristics shall not be used unless a thorough examination and tests
as have been mentioned in clause (b) has been carried out by a competent
person and certificate of such examination and tests signed by that
competent person has been 'obtained and is kept available for inspection.
(5) Safety ventilation. - (a) Every oven or drier shall
be provided with a positive and effective safety ventilation
I Omitted by GO. Ms. No. 141, Lab. and Empt. (M-2), dated 26-10-2005.
2 Subs. by GO. Ms. No. 1717, Labour, dated the 2nd September, 1986.
TAMIL NADU FACTORIES RULES, 1950 [R. 6 " lBJ
system using one or more motor driven centrifugal fans 50 as
to dilute any mixture of air and any flammable substance that
may be formed within the oven or drier and maintain the concen
tration of the flammable substance in the air at a sate level
of dilution.
(b) The safe level of dilution reierred to in clause
(a) shall be so as to achieve a concentration of the concerned
flammable substance in air of not more than 25 per cent, of
its lower explosive lirnil r
Provided that a level of concentration in air up to 5-'.J
,Jer cent. of the lower· explosive limit of the concerned flammable
substance may be permitted to exist subject to installation and
.nalntenance of an automatic device which, -
( i) shows continuously the concentration of the flam
mable substance in air present in the oven or drier at any instant;
(i i) sounds an alarm when the concentration of the
Ilam.nable substance in air in any part of the oven or drier, rea
ches· a level of SO per cent. of its lower explosive limit; and
(iii) shuts down the heating system of the oven or
drier automatically when the concentration in air of the flammable
substance in any part of [he oven or drier reaches a level of
60 per cent. of its lower explosive limit, is provided to the oven
or drier and maintained in efficient working condition.
(c) No oven or drier shall be operated without its
safety ventilation system working in an efficient manner.
(d) No oven or drier shall be operated with a level
of dilution less than what is referred to in clause (b).
(e) Exhaust ducts of safety ventilation system should
be so designed and placed that their ducts discharge the mixture
of air and flammable substance away from the work rooms and
not near windows or doors or other openings from where the
mixture could re-enter the work rooms.
(f) The fresh air admitted into the oven or drier by
R.61AAl f AMIL NADU FACTORIES RULES, 1950
means ·· of the safety ventilation system shall be circulated adequa
tely by means of circulating fan or fans through all parts of the
oven or drier so as to ensure that there are no locations where
the flammable substance can accumulate in the air or become
pocketed to any dangerous degree.
(g) Throttling dampers in any safety ventilation system
should be so designed by cutting away a ;:iortion of the damper
or otherwise, that the system will handle at least the minimum
ventilation rate required for safety when they are set in their
maximum throttling position.
{6) Explosion panels .- (a) Every oven or drier having
an internal total space of not less than half cubic meter shall
be provided with suitably designed explosion panels so as to allow
release of the pressure of any possible explosion withln the oven
or drier through explosion vents. The area of openlnqs to be provi
ded by means of such vents together with the area of opening,
of any access doors which are provided with suitable arrangements
for their release in case of an explosion, shall be not less than
2,200 square centimetres for every one cubic meter of volume
of the oven or drier. The design of the explosion panels and doors
as abovesaid shall be such as to secure their complete release
under an internal pressure of 0.25 kilogram per square centimetre.
(b) The explosion releasing panels, shall, as far as
practicable, be situated at the roof of the oven or drier or at
those portions of the walls where persons do not remain in connec
tion with operation of the oven or drier.
(7) Interlocking
drier, efficient interlocking
maintained to ensure that, -
(I) all ventilating fans and circulating fans whose
failure would adversely affect the ventilation rate of flow pattern,
are in operation before any mechanical conveyor that may be
provided for feeding the articles or substances to be processed
in the oven or drier is put into operation;
arrangements .- In eadh oven or
arrangements shall be provided and
(ii) failure of any
fans will automatically stop any
( I) as may be provided, as well
of the ventilating or circulating
conveyor as referred to in clause
as stop the fuel supply by closing
I
TAMIL NADU FACTORIES RULES, 1950 [R.61AA]
the shut off valve and shut off the ignition in the case of gas
or oil fired ovens and in the case of electrically heated ovens
switch off the electrical supply to the heaters;
(iii) the abovesaid mechanical conveyor is set in opera
tion before the abovesaid shut off valve Gan be energized; and
(iv) the failure of the abovesaid conveyor will automati
cally close the abovesaid shut off valve in the case of ovens
and driers heated by gas, oil or steam and deactivate the ignition
system, or cut off the electrical heaters in the case of electrically
heated ovens or furnaces.
( 8) A u t o m a t i c Pre-venti lat ion.- Every oven or
drier heated by oil, gas, steam or electricity shall be provided
with an efficient arr,angement for automatic pre-ventilation consist
ing of at least 3 volume changes with fresh air by operation
of the safety ventilation fans and the circulating fans (if used
so as to effect purging of the oven or drier of any mixture of
air and a flammable substance before the heating system ::an
be activated and before the conveyor can be placed in position.)
(9) Temperature contro l .- Every oven or drier shall
be provided with an automatic arrangement to ensure that the
temperature w ithin does not exceed a safe upper preset limit
to be decided in respect of the particular processing being carried
on.
( 10) Mu lt i-stage processes .- Wherever materials are
to be processed in ovens or driers in successive operations, suitable
arrangement should be provided to ensure that the operating tem
prratures necessary for safe operation at each stage are maintained
within the design limits.
( 1 1 ) Combust ib le substances not to drip on e lectri
cal heaters or burners f l a m e . - Effectivl;l arrangements shall
be provided in every oven or drier to prevent dripping of combusti
ble substances on electric heaters or burner tlame used for heating.
( 12) Per iod ical exam inat ion , testing and mainte
nance.- All parts of every oven and drier shall be properly mam-
tained and tnorouqhly examined and the various controls as men
tioned in this rule and the working of the oven or drier tes.ted
at frequent intervals to ensure its safe operation by a r_espons1b�e
person designated by the occupier or manage�, who b_y his _experi
ence and · knowledge of necessary precautions against risks of
explosion, is fit to undertake such work.
(b) A register shall be maintained in which the details
of the various tests carried __ out from time to time under clause
(a) shall be entered and every entry made shall be signed by
the __ person makinq the tests.
( 1 3 ) T r a i n i n g of o p e r a t o r s . - No person shall be assiqned
any ·task connected with operation of any oven or drier u�less
he has completed 18 years of age and he is properly trained.
( 14) P o l y m e r i s i n g machines.- (a) Printed fabric shall
be thoroughly dried by passing them over drying cans or throug_h
hot flue or other equally effective means before the same is
allowed to pass through polymerising machines.
(b) Infra-red ray heaters of polymerising machines
�h::111 be cut off while running the prints.]
1l6l-C. Fragile roofs.- In any factory no person shall be
required or allowed to stand on or pass over or walk on or near
· any roof or ceiling covered with fragile material through which he
is liable to fall, in case it breaks or gives way, a distance of more
than three metres, unless,-
(i) suitable and sufficient ladders, duck ladders or crawling
boards which shall be securely supported, are provided and used;
and -
(ii) a permit to work on the fragile roof is issued to him
each time he is required to work thereon, by a responsible person
of the factory concerned, such as Supervisor, Foreman, Engineer
or Manager.]
61-D. Buildings and structures.-No building, wall, chim
ney bridge, tunnel, road, gallery, stairway, ramp. floor, platform,
staging or other structure, whether of a permanent or temporary
1 Suba. by G O Ms. No. 895. Labour and Employment. dated the 16th
t.l&J,1989. •
[R61D . TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU rACTORIES RULES, 1950 fR.611)
character, shall be constructed, situated or maintained in any
factory in such a marmer as to cause risk of bodily injury.
61[. Machinery and plant.- No machinery, plant or
equipment shall be constructed, situated, operated or· maintained
in any factory in such a manner as to cause risk of bodily injury.
61f. Methods of work.- No process or work shall be
carried on in any factory in such a manner as to cause risk of
bodily injury.
6 1G. Stacking and storing of materials, etc •• -
_No materials or equipment shall be stacked or stored in such
a manner as to cause risk of bodily inju�y.
§[6 UL Specia l provisions regarding e lectricity.
[•••]
1 [ 6 1 - 1 Ship bui lding .md Sh ip Repairing.- ( 1)
Applicat ion.- These rules shall apply in respect of work carried
out in ship building and ship repairing operations,
(2) De f init ions .- In these rules, unless there is anything
repugnant in the subject or context :-
( i) "Cert i f icate of entry" means a certificate which -
(a) is given by a person who is a competent analyst
and w:10 is competent to give such certifica-tes; and
(b) certifies th;1t he has in an adequate and suitable
mamer tested the atmosphere in the oil-tank or oil-tanks s;,ecified
in the certificate and found that having regard to all circumstances
of the case, including the likelihood or otherwise of the atmosphere
bein,1 er becominq dangerous, entry to the oil-tar.11< or oil-tanks
witho•Jt wearing breathing apparatus may in his opinion be permit
ted;
(ii) "hot work" means any work which involves -
§ Originally ins. by G.O. Ms. No. 110, Labour and Employment,
dated the 8th December, 1976. Omitted by G.O. Ms. No. 958,
Labour and Employment, dated the 24th August, 1978.
t Subs. by G.D. Ms. No. 3032, Labour, dated the 15th Nol(em
ber, 1983.
[R.611] TAMIL NADU FACTORIES RULES, 1950
(a) . welding, burning, soldering, brazing, sand biasting
.or chipping by spark producing tools; or
(b) use of non-flame proof electrical equipment
or equipment with internal combustion engines;
and includes any other work which is likely to produce sufficient
heat capable of igniting inflammable gases or vapours.
( i i i ) "naked light certific ate " means a certificate which -
(a) is given by a person who is a competent analyst
to give such certificates; and
(b) certifies that he has in an adequate and suitable
manner tested for the presence of inflammable vapour the oil-tank
cornpar tment space or other part of the vessel specified in the
certificate and found it to be free therefrom and that having
regard to all th� circumstances of the case, including the likelihood
or otherwise of the atmosphere becoming inflammable, the use
of naked lights, fires, lamps or heated rivets or any hot work
to be carried out 'nay in his opinion be permitted in the oil-tan'<
-compar tment, space or other part of the vessel specified in the
certificate;
below
thane,
(iv) "oi l" means any liquid which has a flash point
0 0
130 C (270 F) and also includes lubricating oils, /liquid me-
liquid butane and liquid propane. /
Explanation.- Flash point wherever it occurs in these rules
shall be flash point as determined by Abel Closed Cup or Prousky
Marten Closed Cup Procedures as described in 1.5: 1448-1950.
(v) "Oil-tank" means any tank or compartment in
'N'1ich oil is or has been carried ;
(vi) --'.!..the operations" means -
(a) construction, reconstruction or breaking up
of any ship or vessel, repairing, refitting, painting and finishing;
(b) the scalling, scrufing or cleaning of its boilers
(including combustion chambers or smoke boxes); and
(c) the cleaning of its bilges or oil-fuel-tanks
or any of its tanks last used tor carrying oil.
TAMIL NADU FACTORIES PULES, 1950 [R. 61-1
Explanation.-For the purpose of this clause, the expression
' o i l ' means oil or any description ;
(vi i) " S h i p and vessel." have the same meanings as in
the Merchant Shipping Act, 1958 (Central Act 44 of 1 9 5 8 ) ;
(viii) "Shipyard " means any yard of dry dock (including
the precincts thereof) in which ships or vessels are constructed,
reconstructed, repaired, refitted or finished;
• (ix) " S t a g e " means any temporary platform on or from
which persons employed perform work in connection with the
operations, but does not include a boatswain's chair;
(x) "Stag ing" includes any stage, any upright thwart,
thwart pin, wedge, distance piece, belt or o ther app l iance or
material, not being part of the s tructure of the vessel, which is used
in connection with the support of any stage, and any guard-rails
connected with a stage;
(x i) " tanker" means a vessel constructed or adapted for
carrying a cargo of oil in bulk.
(3) Access and stagingi=General access to vessels in a ship·
yard.-All main gangways g iv ing general access to a vessel in a
shipyard, whether from the ground or from a wharf or quay , and
all cross gangways leading from such a main gangway on to the
vessel, shall- .
(a) be at least 60 cm. w ide ;
(b) be securely protected on each s ide to a height of at
least 90 cm . by strongly constructed upper and lower hand-rai ls and
by a secure toe board projec t ing at least 1 5 c.m . above the floor ;
(c) be a good construction, of sound material and
adequate strength ;
(d) be stable and wherever practicable, of permanent
construction ; ·
(e) be kept in position as long as required ; and
(f) maintained in good repairs.
,(4) Access to dry dock.-(i) Every flight of steps giving
access from ground level either to an altar or to the bottom of a ·
dry dock shall be provided throughout on each side w ith a substan
tial band-rail. In the case of an open side, secure fencing to a hei
ght of at least 90 cm . shall be provided by means of upper and lower
rails, taut ropes or chains, or by other equally safe means. For
the purpose of this sub-rule a flight of steps which is divided into
R. 61-I]
the chute and steps, shall be deemed to be one flight of steps.
(ii) Such hand-rails and fencings as aforesaid shall be
kept in position save when and to the extent to which thei� absence
is necessary (whether or not for the purposes of the operations), for
the access ofpersons, or for the movement of materials or vessels
or for traffic or working or for repair, but hand-rails or fencing
removed for any of those purposes shall be kept readily available
and shall be replaced as soon as practicable.
(5) Access to vessels in dry dock -(i) If a ship is lying in
dry dock for the purpose of undergoing any of the operations, there
shall be provided means of access for the use of workers at such
times as they have to pass to, or from, the ship or dry dock-s-
(a) where reasonably practicable, one or more ship's
accommodation ladders; or
(b) one or more soundly constructed gangways or
similar constructions.
(ii) The means so provided shall be not less than 55 cm.
wide, properly secured and fenced throughout on each side to a
clear height of 90 cm. by means of upper and lower rails, taut ropes
or chains or by any other safe means, except that in the case of· the
· ship's accommodation ladder, such fencing shall be necessary on
one s ide only, providedwhere the other side is properly protected
by the ship's side.
(iii) Where at any dry dock, there is a ·gangway giving
access from an altar of the dock to a vessel which is in the dock for
the purpose of undergoing any of the operations, and the edge of
the altar is unfenced, adequate hand ho lds sha l l be available for
full length of the altar which workers commonly use when passing
between the gangway and the nearest flight · of steps which gives
access to ground level.
(6) Access to and from bulkwarks.-Where there is a gang
way leading on to a bulkwark of a vessel there sha l l be provided a
platform at the in-board end of the gangway with safe means of
access therefrom to the decks :
Provided that such a platform is not practicable, a second
gangway or stairway leading from a bulkwark on to the deck which
are either attached to the first mentioned gangway or place conti
guous to it, in which case means of access securely protected by
fencing shall be provided from the one to the other.
(7) Access to staging, etc. -(i) Whether outside staging is
erected in a shipyard, there shall be provided sufficient ladders
TAMIL NADU FACTORrns RULES, 1950
two by·� chute for materials, with no space between either side of
IR 61-r
givmr direct access to the stages having regard to the extent. of the
staging and to the work to be done.
( i i ) Where a vessel is under construction or reconstruc
tion and workers are liable to go forward or aft or a thwartship
across or along uncovered deck-beams, or across or along floors,
sufficient planks shall be provided on these deck-beams or on those
floors for the purpose of access to or from places of work and
sufficient and suitable portable ladders shall be provided so as to
give access either from the ground or outer bottom plating to the
top of the floor.
(i i i) Without prejudice to any other provision contained
in clause (ii) of sub-rule (5) requiring greater width, no footway
or passageway, constructed of planks shall be less than 45 cm.
wide.
(8) (i) Subject to clauses ( i i) and (iii) of this sub-rule,
every ladder which affords a means of access, communication or
support to person shall -
(a) be sound ly constructed and properly ma inta ined ;
(b) be of adequate strength for the purpose for which
it is used ; and
(c) be securely fixed either-
(i) as near its upper rest ing place as poss ib le ; or
(i i) where this is impracticable at its base, or
where such fix ing is impract icable , a person shall be s tationed at
the base of the ladder when in use to prevent it from sl ipp ing ; and
(d) Unless there is other adequate hand-ho ld , extend
to a height of at least 75 cm. above the place of landing or the
he ight of the h ighest rung to be reached by the foot of any per -on
working on the ladder , as the case may be or, if this is impracti
cable, to the greatest practicable height.
( i i ) Requirements of sub-clauses (c) and (d) of clause ( i )
above shall not apply to fixed ladders of a sh ip or to rope ladders .
Effective measures by means of roping off or other similar means
sha l l be taken to prevent the use of fixed ladders of a ship
which do not comply w ith requirements of sub-clauses (a) and (b)
of clause (i) above.
( i i i) Any worker who removes any ladder and acts it up
in a new position shall, as regards that ladder; comply with
requirements of sub-clause (c) of clause (I) above.
(iv) Rope ladders shall provide foothold of .a depth
including any space beh ind the ladder of not Jess than 1 2 cm . and
suitable provisions shall be made for preventing such ladders from
twisting.
TAMIL NADlf FACTORIES RULBS, 1950
. lR.61i]
(9) Lashing of ladders.-(i) A fibre rope, or a rope made
with strands consisting of wire cores covered with fibre, s h a l l not
be used to secure a ladder used for the purpose of the o p e r a t i o n s .
(ii) A wire rope shall not be us�d to s�c�re any such
ladder unless its ends are ferruled, but t h i s provision s h a l l not
apply in the case of an end which is so situated or protected th.at a
person using the ladder is not liable to come into contact with tt so
as to suffer injury.
(IO) Material for staging.-(i) A s u ffi c i e n t s u p p l y of sound
and substantial material and appliances sha l l be available in con
venient place or places for the construction of staging.
(ii) All planks and other mat e r i a l s and appliances inten
ded to be used or re-used for staging sha ll be carefully examined
before being taken into use or re-use in any s t ag ing. Every exami
nation required by this clause s hall be carried out by a person
competent for the purpose.
(I I ) Maintenance of staging, dry dock altars and shoring
si/ls.-(i) All stagings and every part thereof sh a ll b e of good
construction, of suitable and s o und materials and of adequate
strength for the purpose of which it is used and shal l be properly
maintained, and every upright and thwart shall be kept so fixed,
secured or placed in position as to prevent accidental dis p la c ement .
(ii) Al l planks forming stages shall be securely fastened to
prevent them from s l ipp ing unless they extend 45 cm. or more
beyond the inside edge of the thwart or support on which they
rest.
(i i i) All staging used in connection with the operations
sha ll be inspected before use, and thereafter at regu lar and frequent
intervals, by a responsible person.
(iv) Al l dry dock altars and shor ing s i l l s on or from which
persons perform work in connection with the ope rations sha l l be
of sound construction and properly ma intaine d .
(v) All parts of stages, all parts of foot ways or passage
ways constructed of p lanks , and al l parts of the dry dock a lta rs or
shoring sills, being parts on or from which persons perform work
in connection with the operations, shall be kept clear of a l l subs
tances likely to make foot-hold or handhold insecure.
(12) Using of upright for hoisting block.-(1) If any
upright forming part of staging is used as a fixing for a pu l ley
block for hois t ing materials- -
(a) it sh a ll be properly housed in the ground or shall
otherwise be adequately secured so as to prevent it from r i s ing; and
TAMIL NADU FACTORIES RULBS, 1950
TAMIL NADU FACTORIBS RULES, 1950 LR.61IJ
(b) it shall be suitably protected against damage by
the action of the chain or wire or other means of securing the
pulley block to the upright.
( i i ) No upright forming part of staging shall be used as
an anchorage for a load pulley block, unless the upright is not
likely to be displaced by such use.
( 13) Support of stages on planks.-Planks supported on
the rungs of ladders shall not be used to support stages.
(14) Maintenance of suspended stages.-(i) Stages suspen
ded by ropes or chains shall be secured as far as possible so as to
prevent them from swinging.
(i i) A fibre rope, or a rope made of strands consisting
of wire cores covered with fibre, shall not be used for suspending
a stage except that fibre ropes may be used in the case of a stage
of which the supension ropes are received through blocks.
( iii) Chains, ropes, blocks and other gear used for the
suspension of stages shal l be of sound material, adequate strength
and· suitable quality, and in good condition.
(iv) Appropriate steps sh�ll be taken to prevent ropes or
chains used for supporting a stage from coming into contact with
sharp edges of any part of a vessel.
( 1 5 ) Provision of Boatswin's Chairs.-(i) Boatswain's
chairs and chains ropes or other gear used for their suspension
shall be of sound materials, adequate strength and suitable quality
and the chains, ropes or other gear shall be securely attached.
(ii) Suitable measures sha l l be taken to prevent where
possible the sp inning of a boatswain's chair to prevent the tipp ing
of a boatswain's chair and to prevent any occupant falling there
from.
(16) Rising stages. -All planks forming a ris ing stage at
the bow end of a vessel shall be securely fastened to prevent them
from s l ipping.
( 1 7 ) Width of staging.-Without prejudice to the other
provisions of this rule all stages shall be sufficient width as is
reasonable in all the circumstances of the case to secure the safety
of the persons working thereon.
(18) Maintenance of stages from which a person is liable 10:
Jail more than 2 m. or into water while working.-(i) This sub-rule
applies to stages from which a person is liable to fall a distance
of more. than 2 m . or into water in which there is a risk of drown
ing while working.
(R61I TAMIL NADU FACTORIES RULES, 1950
(ii) Every stage to which this sub-rule applies-
(a) if it is not a side immediately adjacent to any part
of a vessel, ·
(b) shall be so constructed or placed that a person is
not liable to fall while working as aforesaid through a gap in the
staging not being a gap necessary and having regard to the nature
of the work being carried on ;
(c) shall be at least 45 cm. on wide.
(iii) Every side of a stage to which this sub-rule applies
shall-
(a) if it is not a side immediately adjacent to any part
of a vessel, be fenced subject to the provisions of clauses (iv) to
(vii) of this sub-rule, with a guard rail or guard rails to a height
of at least 1 m. above the stage, which rail or rails shall be so
placed as to prevent the fall of persons from the stage or from any
standing raised standing place on the stage ; or
(b) if it is a side immediately adjacent to any part of
a vessel, be placed to that part having regard to the nature of the
work being carried on and to the nature of the structure of the
vessel.
(iv) In the case of stages which are suspended ropes or
chains, and which are used solely for painting, the fencing required
by sub-clause (a) of clause ( i i i ) of this sub-ru le may be provided
by means of taut guard rope or taut guard ropes.
(v) No side of a stage or, as the case may be. no part of
the side of a stage need be fenced in pursuance of sub-clause (a)
of clause ( i i i) of this sub-rule in cases where and so long as, the
nature of the work being carried on makes the fencing of that side,
or, as the case may be, that part impracticable.
(vi) Guard rails provided in pursuance of sub-clause (a)
of clause (iii) of this subrule may be removed for the access of
persons ·or for the movement of materials only and replaced
immediately.
(vii) Where it is not reasonably prac t icable to comply
with the provisions of sub -clause (a) of clause (i i i) of this sub -rule,
workers shall be provided with suitable safety belts equipped with .
life lines which are secured with a minimum amount of slack to a
fixed structure.
Further precautions against fall of persons, materials and
articles.
(19) Fencing of dry docks.-(i) Fencing shall be provided
at or near the edges of a dry dock at ground level, including
TAMIL NADU FACTORIES RULES, 1950 (R.611]
edges above flights of steps and chutes for materials. The height
of such fencing shall at a no point be less than 1 m.
{ii) Such fencing as aforesaid shall be kept in position
safe when and to the extent to which its absence is necessary
(whether or not for the purposes or the operations) for the access
of persons, or for movement of materials or vessels or for traffic
or working, or for repair, but fencing removed for any of these
purposes shall be kept readily available and shall be replaced
immediately.
(20) Protection of openings.-(i) Every side or edge of an
opening in a dock or tank top of a vessel being aside or edge
which may be a source of danger to workers shall, except where
and while the open ing is securely covered or where the side or
edge is protected to a height of not less than 75 cm . by a coaming
or other part of the vessel, be provided with fencing to a height of
not less than 90 cm above the edge of side and such fencing shall
be kept in position save when and to the extent to which its absence
is necessary (whether or not for the purposes of the operations),
.'.'Jr the access of persons, or for the movement of materials, or for
traffic or working, or for repair, but fencing removed for any
of these purposes shall be kept readi ly available and shall be
replaced as soon as practicable.
(ii) Clause (i) above shall not apply-
(a) to that part of an opening in a deck or tank top
which is at the head of a stairway or ladder-way intended to be
used while the operations are being carried on ; or
(b) to parts of a deck or tank top which are intended
to be plated, except such parts where the plating has necessarily to
be delayed so that the opening may be used for the purpose of the
operations.
(2 1) Fall of articles from stages -Where workers are at
work outside a vessel on stage adjacent to part of the structure of
the vessel and other workers are at work directly beneath that stage,
the planks of the stage sha l l be in such a position that no article
liable to cause injury to the workers can fall between the plan ks,
and the inside plank of the stage shall be placed as near as practi
cable to the structure of the vessel having regard to the nature of
the work being carried on.
(22) Provision of boxes for rivets, etc.-(i) Boxes or other
suitable receptacles for rivets, nuts, bolts and welding rods shall be
provided for the use of workers.
(ii) It sha l l be the duty of the workers to use so far as
practicable the boxes or other su itable receptacles so provided.
[R.611]
(23) Prohibition of throwing down materials and articles
-(i) Subject to the provision of clause (ii) of this sub.rule, part
of staging, tools and other articles and materials shall not be
thrown down from a height where they are liable to cause injury to
workers but shall be properly lowered.
(ii) When the work to be done necessarily involves the
throwing down from a height of articles or materials, conspicuous
notice shall be pasted to warn persons from working or passing
underneath the place from which articles or materials may fall and
the work shall be done under the direct supervision of a supervisor
in charge of the work.
(iii) No person shall throw down any articles or
materials from height except in accordance with the requirements
of this sub-rule.
(24) Rising of loose articles or materials.s-So far as practi
cable, steps shall be taken to m inimise the risk arising from loose
articles or materials being left lying about in any place from which
they may fall on workers or persons passing underneath.
Raising and Lowering.
(25) Precaution for secureness of loads.-(i) Loads shall be
securely suspended or supported whi lst be ing raised or lowered,
and all reasonable precautions shall be taken to prevent danger
from slipping or displacement. -
(ii) Where by reasons of the nature of position of the
operations load is liable, whilst being moved by a lifting machine
or lifting tackle, to come into contact with any object so that the
object may became displaced, special measures sha l l be adopted
to prevent the danger so far as reasonably practicable.
(26) Support of lifting machinery and Iift ing tackle.-Every
lifting machine and al l l ift ing tackles sha l l be adequately and
suitably supported or suspended having regard to the purpose for
which it is used.
(27) Wire ropes with broken wires.-No wire rope shall
be used if in any length of ten times the diameters of the w ire
rope the total number of visible 'broken wires exceeds five per cent.
of the total number of wires, or if the rope shows signs of exces
sive wear or corrosion or other serious defect.
(28) Splices in wire ropes.-A thimble or loop splices
made in any wire rope shall have at least three tucks with a whole
strand of the rope and two tucks with one half of the wires cut
out of each strand. All tucks shall be against the lay 9f' the rope:
TAMIL NADU FACTORIES RuLeS, 1950
TAMIL NADU FACTOR(BS RULES, 1950
[R.61-1
Provided that this sub-rule shall not operate to prevent the
use of another form of splice which can be shown to be as efticient
as the form of splice specified in this sub-rule.
(29) Restriction in the use of knotted chains, elc.-(i) No
chain or wire rope shall be used when there is a knot tied in any
part thereof.
(ii) No chain which is shortened. or joined to another
chain by means of bolts and nuts shall be used:
Provided that this does not exclude the use of a chain bolted
or.joined to another chain by an approved and properly con
structed attachment.
. ( 3 0 ) Precautions against damage to chains and wire ropes.
Appropriate steps shall be taken to prevent so· far as practicable,
the use of chains or wire ropes for raising or lowering in circum
stances in which they are in or l iable to come into contact with
sharp edges of plant, materials or loads, or with sharp edges of
any part of the vessel on which work is being carried on.
(3 1 ) Loads on lifting appliances.-No load shall be left
suspended from a l ift ing appliance other than a self sustaining,
manually operated lifting app l iance unless there is competent
person in charge of the appliance while the load is so left.
(32) Ascertaining the weights of heavy Joads.-Where there
is reason to believe that a load being lifted or lowered on a lifting
appliance weighs more than 20 tonnes, i ts weight shall be ascertain
ed by means of an accurate weighing machine or by the estimation
of a person competent for the purpose, and shal l be clearly marked
on the load :
Provided that this sub -rule shall not apply to any load lifred
or lowered by a crane which has either a fixed or a derricking j ib
and which is fitted with an approved type of indicatory in good
working order which-
(a) indicates clearly to the dr iver or person operating
the crane when the load be ing carr ied approaches the safe working
load of the crane for the radius of the j i b at which the load is
carried ; and
(b) gives an efficient sound signal when the load
moved is in excess of the safe working load of the crane at that
radius .
Precautions against asphyxiation, injuries, fumes or explosions:
(33) Certification for entry into confined spaces.-A space
shall not be cert ified under section 36 (3) (a) of the Act unless-
[R611]
(a) effective steps have been taken te prevent any
ingress of dangerous fumes; .
· (b) any sludge or other deposit liable to give off danger·
ous fumes has been removed and the space contains no other
material liable to give off dangerous fumes; and
(c) the space has been adequately ventilated and
testedfor dangerous fumes and has a supply of air adequate for
respiration ; but no account shall be taken for the purposes of
clause (b) of this sub-rule of any deposit or other material liable
to give off dangerous fume in insignificant quantities only.
(34) Precautions against shortage of oxygen.-No person
shall enter or remain in any confined space in a vessel, being a
confined space in which there is reason to apprehend that the
proportion of oxygen in the air is so low as to involve risk of
persons being overcome, unless either-
- (a) the space has been and remains adequately ventilated
and a responsible person bas tested it and certified that it is safe
for entry without breathing apparatus, or
(b) he is wearing a suitable breathing apparatus and a
safety be lt securely attached to a rope, the free end of which is
held by a person standing outside the confi!ed space.
Explanation.-" a responsible person" means a supervisory
personnel who is competent to test the confined space and issue a
certificate.
(35) Restriction for the use of rivet fires.-(i) Rivet fires
shall not be taken into or used in or remain in any confined space
on board or in a vessel unless there is adequate ventilation to
prevent the accumulation of fumes.
(ii) No person employed shall move a rivet fire into any
confined space on board or in a vessel unless he has been authorised
by his employer to move the fire into that space.
(36) Use of gas cylinders and acetylene generators.-(i) No
cylinder which contains or has contained oxygen or any inflamma
ble gas or vapour at a pressure above atmospheric pressure and no
acetylene generating plant, shall be installed or placed with 5 m.
of any substantial source of heat (including any boiler or furnace
when alight) other than the burner or blow pipe operated from the
_ cylinder or plant.
(i i) No such cylinder and no such plant shall be taken
below the weather deck in the case of a vessel undergoing repair,
or below the topmost completed deck in the case of a vessel under
construction, unless it is installed or placed in a part of the vessel
TAMIJ, NADU FACTORIES Rutss; 1950
TAMIL NADU FACTOttlES RULl?S, 1950 R.61IJ
which is adequately ventilated to prevent any dangerous concen
tration of gas or fumes.
(37) Restrictionin. the use of acetylene generotors.-(i) 1:'he
following shall be observed as respects any acetylene generating
plant-
(a) no such plant shall be installed or placed in any
confined space unless effective and suitable provision is made for
securing and maintaining the adequate ventilation of that space so
as to prevent, so far as practicable, any dangerous accumulation
of gas;
-{b) any person attending or operating any such plant
shall have been fully instructed in its working and copy of the
maker's instructions for that type of plant shall be constantly
available for his use;
(c) the charging and cleaning of such plant shall so far
as practicable be done during dayl ight ;
(d) partly spent calcium carbide shall not be recharged
· into an acetylene generator.
(ii) No person shall smoke or strike a light or take a
naked light or a lamp in or into any acetylene generator house or .
shed or in or into dangerous proximity to any acetylene generating
p lant in the open air or on board a vessel :
Provided that this clause shall not apply as respects a generator
in the open air or on board a vessel which since it was last charged,
has been thoroughly cleaned and freed from any calcium carbide
and acetylene gas.
(iii) A prominent notice prohibiting smok ing. naked
lights and lamps shall be exhibited on or near every acetylene
generating plant whilst it is charged or is be ing charged or is being
cleaned.
(38) Use of proper apparatus for curring, welding or heating
metal.-(i) Pipes or hoses for the supply of oxygen or any
inflammable gases or vapour to any apparatus for cutting, welding
or heating metal shall be of good construction and sound material
and be properly maintained.
(ii) Such pipes or hoses shall be securely attached to the
apparatus and other connections by means of suitable clips or
other equally effective appliances.
(iii) Efficient reducing and regulating valves for reducing
the pressure of the gases shall be provided and maintained in
connection with all cylinders containing oxygen or any inflammable
gases or vapour at a pressure above atmospheric pressure while the
(iv) Where acetylene gas is used for cutting, welding or
heating metal -
(a) properly constructed and efficien� b�ck-p�essure
valve and flame arrester shall be provided and maintained in the
acetylene supply pipe between each burner or bl<?w-�i�e and !he
acetylene generator, cylinder or container from which it is supplied
and shall be placed as near as practicable to the burner or blow·
pipe except that those requirements shall not a_pplr where an
acetylene cylinder serves only one burner or blow pipe , and
(b) any hydraulic valves provided in pursuance of
sub-clause (a) of clause (iv) shall be inspected on each day by
every person who uses the burner or blow-pipe on that day and it
shall be the duty of every worker who used the burner or blow-pipe
to inspect the hydraulic valve accordingly.
(v) The operating valves of burners or blow-pipes to
which oxygen or any inflammable gases or vapour is supplied for
the purpose of cutting, welding or heating metal shall be so
constructed, or the operating mechanism shall be so protected
that the valves cannot be opened accidentally,
--(39) Precaution after use of apparatus for cutting, welding
�r heating meta/.-(i) In the case of apparatus on board a vessel
and used for cutting, welding or heating metal with the aid of oxygen
or any inflammable gas or vapour supplied at a pressure above
atmospheric pressure, the precautions specified in this sub-rule shall
be taken when such use ceases for the day or for a substantial
period, and the apparatus is to be left on board, but need not be
taken when such use is discontinued merely during short interrup
tions of work. The requirements in clauses (iii) and (iv) of this
sub-rule shall not apply during a meal interval, provided that a
responsible person is placed in charge of the plant and epuipment
referred to therein.
(ii) Supply valves of cylinders, generators and gas mains
shall be securely closed and the valve key shall be kept in the
custody of a responsible person.
(iii) Movable pipes or hoses used for conveying oxygen
or inflammable gas or vapour and the welding and cutting torches,
shall, in the case of a vessel undergoing construction, be brought
to the topmost completed deck, or in the case of a vessel under·
going repair, to a weather deck or in either case to some other
place of safety which is adequately ventilated to prevent any
dangerous concentration of gas or fumes : ·
gases or vapours from sugi cylinders are being used in any process
TAMIL NADU FACTORIES RULES, 1950
of cutting; welding or heating metal.
1m1,>ract1cable to comply· with the foregoing requirements of this
clause, the pipes or hoses shall be disconnected from cylinders
generators or gas mains, as the case may be. '
(iv) When cylinders or acetylene generating plant have
been taken below deck as permitted by clause (ii) of sub-rule (36).
such cylinders or acetylene generating plant shall be brought to a
weather deck or, in the case of a vessel undergoing construction to
the topmost completed deck.
(40) Naked lights and hot works on oil-carrying vessels.:-.
(i) Subject to the provisions of clause {ii) of this sub-rule and to
the provisions of sub-rule (48) and without prejudice to the provi
sions of sub-rules (46) and (47), no naked light, fire' or lamp (other
than a safety lamp of a type approved for the purpose of this
sub-rule r+
(a) shall be permitted to be applied to, or to be in.
or any hot work permitted to be carried out in any part of a tanker,
unless a naked light certificate has been obtained and is in force
in respect of these parts ·of the tanker for which, in the opinion of
a competent analyst, a naked light certificate is necessary :
Provided that a -naked light, fire or lamp of a kind specified
by a competent analyst may be applied to or be in, or any hot
work of a type specified by him carried on, in any part of -the
tanker so specified,
{b) shall be permitted-
(i) to be in any oil tank on board or in a vessel in
which oil tank the oil last carried was having a flash point of less
than 23°C (75°F) or was liquid methane, liquid propane or l iqu id
bu t a n e ;
(ii) to be applied, to the outer surface of any o i l
tanker on board or in a vessel in which o i l-tank the oil last
carried was such oil as aforesaid or any work of such a nature
which is likely to produce suffic ient heat capable of l ighting inflam
mable gases or vapours permitted to be carried ou_t .on the _outer
surface of such oil tank or vessel, unless a naked light certificate
has previously been obtained on the same day and is in force in
respect of that oil t a nk;
(iii) to be applied to the outer surface of; or to be
in any compartment or space adjacent to an oil-tank on board or
in' a vessel in which oil tank the oil last carried was such oil as
aforesaid or anv hot work permitted to be carried out in such
compart�ent or space as aforesaid, or any work of such nature
which is likely to produce sufficient heat capable of igniting inflam
mable gases or vapours, permitted to be carried out on the outer
TAMIL NAEU FACTORIES RULES, 1950 [R.611J
. ' Provided that where, �wing to the nature of the work, it is
[R.611] . TAMIL NADU FACTORIES RULES, i950
surface of such compartment or space, unless naked light certificate
has previously been obtained on the same day and is in force iu
respect of that compartment or space:
Provided that where in any such case referred to in items (i) ,
(ii) and (i i i) of this clause a competent analyst has certified
that daily naked light cert ificates ar� unne�essary or are necessary
only to a specified extent such a daily certificate need not be obtai
ned or as the case may be, need only be obtained to the specified
exten t ;
(c) shal l be permitted to be applied to the outer
surface of, or be in , any o i l- tank on board or in a vessel or any
hot work perm i t ted to be carried out in any such oi l-tank or vessel
or any work of such nature which is l ikely to produce sufficient
heat capable of ign it ing inflammable gases or vapours, permitted
to be carried out on the outer surface of the oil-tank or vessel,
unless, since oil was last carried in that oi l-tank, a naked light
certificate has been obtained and is in force in respect of that
o i l - tank ;
(d) sha ll be permitted to be appl ied to the outer surface
of, or to be in , any compartment or space adjacent to an oil-tank
on board or in a vessel or any hot work permitted to be carried .
out in any such compartment or space or any work of such nature
which is l ikely to produce sufficient beat capable of ignit ing
inflammable gases or vapours, permitted to be carried out on the
outer surface of any such compartment or space, unless, since oil
was last carried as cargo in that oil-tank, a naked l ight certificate
has been obtained and is in force in respect of that compartment
or space.
(ii) Notwithstand ing anything in clause (i) of this sub
rule, heated rivets may be permitted in any place without naked
light certificate being in force- in respect of that place if expressly
so authorised by a competent analyst who certifies that after
adequate and suitable testing, he is satisfied having regard to all the
circumstances of the atmosphere becoming ease including the
likelihood or otherwise of the atmosphere becoming flammable
that the place is sufficiently free from flammable vapour, but such
heated rivets shall where practicable, be passed through tubes.
(iii). . No person shall introduce, have or apply naked
light, fire or lamp (other than safety lamp of a type approved for
the purpose of this rule) into, in or · to any place where they are
prohibited by this rule.
(iv) No person shall carry out bot work or any work of
such nature which is likely to produce sufficient heat capable of
TAMIL NADU FACTORHlS RULl"S, 1950 R.611]
ign i t ing inflammable gases or vapours, in any place or any surface
where they are prohibited by this rule.
Explanation.-' Competent analyst' means an analyst who is
competent to give a naked light certificate,
(41) Restrictions for entering oll-tanks.-(i) No person
(other than an analyst entering with a view to issuing a certificate
of entry) shall, unless he is wearing a breathing apparatus of a type
approved for the purpose of this sub-rule, enter or remain in an
oil-tank on board or in a vessel unless, since the oil-tank last con
tained oil, a certificate of entry has been obtained and is in force in
respect of the tank.
(ii) Without prejudice to clause (i) of this sub-rule, no
person (other than an analyst entering as aforesaid) shall be
allowed or required to enter or remain in an oil-tank on board or
in a vessel in which oil-tank the o i l last carried was oil having a
flash point of Jess than 23°C (73 ° F) unless since the oil-tank last
contained oi l , an analyst has certified that the atmosphere is
sufficiently free from inflammable mixture.
(iii) The provisions of this sub-rule are without pre·
judice to the requirement of sub-rule (34).
( 4 2) 'Duratlon of certificate.-Any naked light certificate or
cert ificate of entry may be issued subject to a condition that it
shall not remain in force after a time specified in the certificate.
(43) Posting of certijicates.-Every occupier fQr__ whom a
naked light certificate or a certificate of entry is obtained shall
ensure that the certificate or a duplicate thereof is posted as soon
as may be and remains posted in a position where it may be con·
veniently read by al l persons concerned.
(44) Maintaining safe atmosplzere.-(i) When conditions
in an oil-tank are such in respect of which a naked light certificate
has been issued that there is a possibility of oil vapour being
released from res idues or other sources, test shall be carried out by
a competent analyst at such intervals as may be required so as to
ensure that the cond i t ions in the tank are maintained safe.
(ii) Whenever ho t work is carried on or naked light, fire
or lamp is allowed to be, on the weather deck over spaces, in
respect of which a naked light certificate has not been issued, all
covers of manholes and openings on deck and all valves (except
those which are connected to high vent pipes) connecting the
weather deck with the said spaces, shall be closed.
(iii) A record of all the tests carried out for the purpose
of sub-rules (34), (40) and (41) shall be maintained in a
the tests.
(45) Cleaning of oil-tanks .-· (i) Subject to t�e proyisions
of sub-rule (48), before a lest for flammable vapour rs carried out
with a view to the issue of a naked light certificate for the purposes
of sub-rule (40) in respect of an oil-tank on board or in a vessel,
that oil-tank shall, since oil was last introduced into the tank, be
cleaned and ventilated in accordance with clause (ii) of this sub.
rule.
(i i) The said clean ing and ven t i lation shall be carried
out by the fo llowing methods-
(a) the o i l - tank shall be treated in such manner and
for such period as w i l l ensure the vapourisation of all volatile o i l ;
(b) a It residual oil and any sludge or other deposit in
the o i l-tank shal l be removed therefrom; and
(c) after the oil-tank has been so c!eaned-
(i) all covers of mauhules and other openings
therein shall be removed and it shall be thoroughly vent i lated by
mechanical or other efficient means with a view to the removal of
a l l o i l vapour ; and then
( i i ) the in ter ior surfaces, if any deposit remains
thereon shal be washed or scraped down .
(46) Invalidation of ccrtijicates.-(i) If during the course
of work in , or to the other surface of, any part of a tanker or air
craft carrier, any pipe or tank joint is opened or broken or any
other event occurs so that there is a risk of oil vapour entering or
ar is ing in that part of the tanker or aircraft carrier, that work sha l l
be suspended and thereafter any certificate or entry previously
issued in respect of any oil-tank in that part and any naked l ight
certificate previously issued in respect of that part shall be no
longer in force.
( i i ) If ( in tbe case of a vessel other than a tanker or a ir·
craft carrier) during the course of work, in any oil-pipe or in any
compartment or space adjacent thereto , any pipe or tank joint is
opened or broken or any other event occurs so that there is a risk
of oil vapour enter ing or arising in the oil-tank or in any compart
ment or space adjacent thereto shall be suspended and thereafter
any certificate of entry prev iously issued in respect of the oil-tank,
and any- naked light certificate previously issued in respect of the
oil-tank, or any compartment or space adjacent thereto sha l l be no
longer in force.
(47) Provisions as to work in other compartments of spaces.
�(i) Without prejudice to the other provisions of these sub-rules,
[R.611} TAMIL NADU FACTORIES RULES, 1950
register which shall furnish the date, time, locations and results of
[R611)
if the presence of oil in such quantity and in such position as to be
likely to give rise to fire or explosion is detected in any part of a
vessel, being a part to which this rule applied ·and in which repairs
of the following kind are to be or are being undertaken that is to
say, repairs involving the use of a naked light, fire _(sic.) purpose of
sub-rule (40) or involving hot work, such repairs shall not be
started or continued unti l a naked light certificate has been issued
or, as the case may be reissued in respect of that part of the vessel.
(ii) This rule shall apply to bilges, shaft, tunnels , pump
rooms, lamp rooms, and to compartments and spaces other than
those to which clause (i) (d) of sub-rule (40) applies;
(48) Exemption.-If the Chief Inspector is satisfied , by
reasons of the nature of the work and the circumstances in which it
is carried out, that any provisions of sub-rules (33) to (45) or part
thereof can be suspended or relaxed without dangers to the health
or safety of any person, he may grant suspension or relaxation in
writing specifying such conditions as he may consider fit. Any
such suspension or relaxation may be revoked at any time .
PRECAUTIONS IN USE OF ELECTRICAL ENERGY
(49) E lectric energy other than that generated by an inde
pendent generating unit on board shall not be taken for use, or
used in , or in connection with any of the operations unless the
body of the ship is securely earthed in such a manner as to ensure
an immediate and safe discharge of energy to the earth. A ship or
vessel shall not be considered as securely earthed for the purpose
of this sub-rule only on account of it being partly submerged in
water.
(50) (i) Electric or welding shall not be carried on in
connection with any of the operations unless separate and fully
insulated welding return conductor or conduc tor as the case may be
of adequate electrical capacity are provided for return of the
current to the transformer or generator of the welding se t :
(ii) The return end of the source of the welding current
shall not be earthed ;
(iii) A 1 1 work on which welding · is carried on shall be
securely earthed independently to an earth electrode by means of
conductor or conductors as the case may be, of adequate capacity,
unless all such work are connected to any structure of the ship or
vessel in such a manner as to ensure adequate connection to earth
as aforesaid.
(51) Cutting of energy in certain cases.-Electric energy shall
be cut off from all portable electric tools and manual electrode
TAMIL NADU FACTORIES RULllS, 1950
[R.611}
rules (34) and J 40) or in any other. confined. spa�e during all timc.,
when such tools or holders are not m operation .
Provided that for determining whether any such portable
electric tool or electrode holder is not in operation, no account
shall be taken of brief interruptions of work occurring during
normal working.:
J Provided further that energy may not be cut-off from any such
equipment if a responsible person is left in charge of it in such tank,
compartment or space concerned:
Provided also that cutting of all electrical energy by "operation
of any switch or control provided on the portable tool or electrodes
holder itself should not be taken as fulfilling the requirement of
this sub-rule.
MISCELLANEOUS SAFETY PROVISIONS
(52) Provisions of sufficient /ight.-AII parts of a vessel and
all other places where the operations are being carried on, and all
approaches to such parts and to places to which a worker may be
required to proceed in the course of his employment, shall be
sufficiently and su itably· lighted. In providing such lighting due
regard shall be given to avoidance of glare and formation of
; shadow, to the safety of the vessel and cargo, oftbe navigation of
other vessels, and to any local statutory requirements as to the
lighting of the harbour or deck.
1 (53) When work shall be permitted in boilers, etc�,-(i) No !I work shall be permi tted in any boiler, boiler furnace or boiler-flue
until it bas been sufficiently cooled to make work safe for the
I
workers.
( i i ) Before any worker enters any steam boiler which is
one or a range of two or more steam boilers-
(a) all inlets through which steam or hot water might
otherwise enter theboiler from any other part of the range shall be
disconnected from that part, or
(b) all valves or taps controlling such entry shall be
closed and securely locked.
( i i i) While workers remain in any steam boiler to which
clause (ii) of this sub-rule applies all such inlets as are referred to
in that sub-rule shall remain disconnected or all such valves or
taps as are therein referred to shall remain closed and securely
locked.
(iv) No worker shall be allowed or required to enter or
.remain in and no person shall enter or remain in, any steam boiler
TAMIL NADU FACTORIES RULES, 1950
holders within any tank, compartment or space referred to in �ub
1°AMIL NADU FACTORIES RULBS, 1950 [R.6111,
to which clause (ii) of this sub-rule applies unless the provisions
of that sub-rule are being complied with.
(54) The hatch beams of any batch in use for the operations
shall, if not removed, be adequately secured to prevent their
displacements.
(55) Bolts which have been jumped-up and re-screwed shall
not be used for securing plates on the sides of vessels, and no
worker shall use such bolts for this purpose.
(56) Work in or 011 life boats.-(i) Before workers · are
permitted to work in or on any life boat, either steward or in
suspended position, precautions shall be taken to prevent the boat
from falling due to accidental tripping of the releasing gear or
movement of the davits, and capsizing of the boat if in checks.
(ii) Workers shal l not be permitted to remain in life
boats whi le the life boats are being hoisted into final steward
position.
PROlECHON WtAR
(57) Hand protection.-Adequate protection for the hands
shall be available for a l l workers when us ing cutting or welding
apparatus to wh ich oxygen or any flammable gas or vapour is
supplied at a pressure greater than atmospheric pressure or when
engaged in machine cau lking or machine revering or in transporting
or stacking plates or in handling plates at machines.
(58) . Protection in connection with cutting or welding i-«
Ii) Suitable goggles fitted with tinted e) e-pieces 'shall be provided
and ma inta ined for all persons employed when using cutting or
welding apparatus to which oxygen or any flammable gas or vapour
is supplied at a pressure above atmospheric pressure.
(ii) There shall be provided and maintained for the use
of all persons employed when engaged in the process of electric
welding-
(a) suitable helments or suitable head-shields or
suitable hand shields to protect the eyes and face from hot meta I
and from rays likely to be injurious; and
(b) suitable gauntlets to protect the hands and fore
arms from hot metal and from rays likely to be injurious.
(iii) When electric welding is in progress at any place
and persons other than those engaged in that process are employed
in a position where the rays are +ikely to be injurious to their eyes, .
screens shall be provided at that place for the protection of these
persons : Provided that when it is not possible to provide. screen,
suitable goggles shal l be provided for their use. /
lR.6p TAMIL NADU FACIORll!S RULl!S, 1950
(59) Eye protection for other processes.-Suitable goggles
of effective screens shall be provided to protect the eye of all
workers in any of the following processes+-
(a) the cutting out or cutting off of cold rivets bolts
from boilers or other plant or from ships ;
(b) the chipping, scaling or scurfing of boilers or ships
plates ;
(c) drilling by means of portable machine tools;
(d) dry grinding of metals.
(60) Head protection.-When workers are employed. in
areas where there is danger of falling objects they shall be provided
with suitable safety helmets.
(61) Provision of safety belts and life-lines .-(i) Whenever
any worker is engaged on work at a place from which he is liable
to fall more than 2 (two) m. he shall be provided with safety belts
equipped with lifelines which are secured with a minimum of slack,
to a fixed structure unless any other effective means such as
provision of guard rails or ropes are taken to prevent his falling.
(ii) All safety belts and lifelines shall be examined once
in six months by a competent person to ensure that no belt or
lifeline which is not in good condition is used.
Hl!ALTH AND WELFARE
(62) Prohibition of employment of young persons in certain
proc'ess.-No young persons shall be employed in-
(a) the application of asbestos by means of a spray ; or
(b) the breaking down for removal of asbestos lagging;
or
(c) the cleaning of sacks or other containers which
: have contained asbestos ; or
(d) the cutting of materials containing asbestos by
. means of portable power-driven saws ; or
(2) the scaling, scurfing or cleaning of boilers, combus
tion chambers or smoke boxes, where his work exposes him to dust
of such a character and to such an extent as to be likely to be
injurious or offensive to persons employed in such work.
(63) Restriction in the use of /ead.-(i) Lead paint shall not
be applied in the form of a spray in the interior painting of any
part of a ship or vessel. .
'(ii) Wherever lead sheathing work is carried on for
making cold storage chambers in the ships, efficient exhaust
TAMIL NADU FACTORIES RULES, 1950 [R. 61 - - 1
droughts with portable extractors should "be provided to remove
the lead fumes from the confined spaces.
(64) Provision of stretchers, ambulances and. ambulance
rooms, etc.-(i) In every shipyard, there shall be provided and .
kept readily available-
(a) at least two numbers of suitably constructed sling
stretchers or other similar appliances for raising injured persons ;
(b) at least two numbers of carrying or wheel stretchers;
(c) at least two numbers of suitable reviving apparatus
and oxygen and the stretchers, appliances and apparatus so provi
ded shall be properly maintained.
(ii) In every shipyard, there shall always be readily
available during working hours a responsible person or responsible
persons whose duty it is to summon an ambulance or other means
of transport if needed in cases of accident or il lness . Legible
copies of a notice indicating that person, or as the case may be these
persons shall be affixed in prominent positions in every shipyard .
( i i i ) Io every shipyard other than a dry dock available
for hire-
(a) in which the number of persons employed normally
exceeds five hundred ; or
(b) in which the number of persons employed normally
exceeds one hundred and which is more than ten miles from a
hospital
there shall be provided and maintained in good order and in
clean condition a properly constructed ambulance room containing
at least the equipment as prescribed in the rule 64 of the Tamil
Nadu Factories Rules, 1950. The room shall be used on ly for the
purpose of treatment and rest and shall be in charge of a suitably
qualified person who shall be readily available during working
hours, and record shall be kept of all cases of accident or sickness
treated at the room.
(65) Restrictions in the employment of young persons.-(i)
No young person shall unt i l he has been employed in a shipyard
or shipyards for at least six months be employed in connection
with the operations in a shipyard on a stage from which, or in any
part of a ship where, he is liable to fall a distance of more than
2 m. or into water in which there is a risk of drown ing .
(ii) Any young person under the age of sixteen shal l ,
when employed in the operations in shipyard, be placed under the
charge of an experienced workman.
(66) Safety supervisions.i--lsi the case of every shipyard
other than a dry deck available for hire be ing a shipyard where the
lR.611] . TAMIL NADU FACTORIES RULBS, 19S0
number of workers regularly or from time to time exceeds five
hundred, a person experienced in the work of such yards shall be
appointed and employed exclusively to exercise general supervision
of the observance of this rule and to promote the safe conduct of
the work generally,)
1[61-J. Reaction Vessels and Kettles.-(1) This rule applies
to reaction and kettles (hereinafter in this rule referred to as reac
tion vessels) which normally work at a pressure not above the at·
mospberic pressure, but in which there is likelihood of pressure
being created above the atmospheric pressure due to reaction get·
ting out of control or any other circumstances. ·
(2) In the event of the vessel being heated by electrical
means, a suitable control device shall be provided to prevent the
temperature exceeding the safe limit.
(3) Where steam is used for heating purposes in reaction
vessel it shall be supplied through· a suitable pressure reducing
valve, (sic.) any other suitable automatic device to prevent the
maximum permissible steam pressure being exceeded, unless the
pressure of the steam in the supply line itself cannot exceed the
said maximum permissible pressure . .
(4) A suitable safety valve or rupture disc of adequate
· size and capacity shall be provided to effectively, prevent the
pressure being built up in the reaction vessel beyond the safe limit.
Effective arrangements shall be made to ensure that the released
· gases, fumes, vapours, liquids or dusts, as the case may be, are led
away and disposed of through suitable pipes without causing any
hazard. Where flammable gases or vapours are likely to be vented
out from the vessel, the discharge end shall be provided with a
ftame arrestor.
(S) Every reaction vessel shall be provided with a pressure
gauge having the appropriate range.
(6) In addition to the devices as mentioned in the fole
going provisions, means shall be provided for automatically stopping
the feed into the vessel as soon as process conditions deviate from·
the normal limits to an extent which can be considered as dangerous.
(7) Where necessary, an effective system for cooling,
flooding or blanketing �hu l l be prov ided, for the purpose of
controlling the reaction and process condi t ions within the safe
limits of temperature and pressure.
(8) An automatic audi tory and visual warning device
shall be provided for clear warn ing whenever process conditions
1 . Ins. by G.O Ms� N.o. 1 1 0 6 , Labour and Employment, ( M-11), date ••
the 28th December, 1976,
exceed the present limits. This device, wherever possible, shall be
integrated with automatic process correction systems.
(9) A notice pointing out the possible circumstances in
which pressures above atmospheric pressure may be built up in the
reaction vessel, the dangers involved and the precautions to be
taken by the operators shall be displayed at a conspicuous place near the
vessel.]
'161-K. Examination of eye sight of certain workers. - (1) No
person shall be employed to operate a crane, locomotive or fork lift
truck or to give signals to crane or locomotive operator unless his eye
sight and colour vision have been examined and declared fit by a qualified
opthalmologist to work whether with or without use of corrective
glasses ..
(2) The eye sight and colour vision of the person employed
as referred to in sub-rule ( I ) shall be examined at least once in every
two years.
(3) Any fee payable for an examination of a person under this
rule and the cost of corrective glasses shall be paid by the occupier
and shall not be recoverable from that person.
2(( 4) The record of examination or re-examination carried out by
the concerned ophthamologist shall be produced on demand.]]
316/-L. Railways in factories. - ( 1 ) This rule shall apply to
railways in the precints of a factory which are not subject to Indian
Railways Act, 1890 (Central Act IX of 1890).
(2) Gateways. -A gateway through which a railway track passes
shall not be used for the general passage of workers into or out of a
factory.
(3) Barriers and turngates. - (a) Where building or walls
contain doors or gates which open to a railway track, a barrier about
I metre high shali be fixed parallel to and about 60 cm. away
from the building or wall outside the opening and extending
I Ins. by GO. Ms. No. 988, Labour, dated the 2nd June, 1986.
2 Subs. by GO. Ms. No. 121 , Labour and Employment (M-2), dated the 3 lstJuly,
2012. .
3 Ins. by GO. Ms. No. 109, Labour. dated the 23rd January, 1985.
THE TAMIL NADU FACTORIES RULES, I 950 [R.61-L
IR.611 i :. TAMIL NADU FACTORIES RULES, 1950
several feet beyond it at either end, so that any person passing out
may become aware of an approaching train when his pace is
checked at the barrier.
If the traffic of the nearest track is all in one direction, the
barrier shall be in the form of a ' L ' with the cod of the short leg
abutt ing on to the wall and the other end opening towards the
approaching train.
(b) If the distance between wall and track cannot be
made to accommodate such a barrier, the barrier or a turngate
shall be placed at the inside of the opening.
(c) Where a footway passes close to a building or other
obstruction as it approaches a railway track, a barrier or a turngate
shall be fixed in such a manner that a person approaching the
track is compelled to move away from the building or obstruction
and thus obtain t ime ly sight of an approaching locomotive or
wagon.
(4) Crowd.-(a) Workers' pay-window, first-aid sfati�ns
and other points where a crowd may collect shall not be placed
near a railway track.
(b) At any time of the day when workers are starting or
ending work, all railways traffic shall cease for not less than five
. minutes.
(5) Locomotives.-(a) No locomotive shall be used in
shunting operations unlessit is in good working order.
(b) Every locomotive and tender shall be provided with
efficient brakes, a l l of which sha ll be ma intained in good working
order. Brake shoes shall be examined at suitably fixed interval
and those that are worn out replaced at once.
(c) Water-gauge glasses of every locomotive, whatever
its boiler pressure, shall be protected with substantial glass or
metal screens.
(d) Suitable steps and hand-holds shall be provided, at
the corners of the locomotive for the use of shunters,
(e} Every locomotive crane sha ll be provided with lifting
and jacking pads at the four corners of .he locomotive for assisting
in re-railing operations.
(f') It shall be clearly indicated on every locomotive
crane in English and in language understood by - t he majority of
the workers in the factory, for what weight of load and at what
radius the crane is safe.
(6) Wagons.-(&) Every wagon (and passenger coach, if
any) shall be provided either with self-acting brakes capable -or
TAMIL NADU fAClORIES Rut.ss, 1950 . R . 6 1 L ! .
being applied continuously or with efficient hand brakes which
shall be maintained, in good working order. The hand brakes
shall be capable of being applied by a person on the ground and
fitted with a device for retaining them in the applied position.
(b) No wagon shall be kept standing within 3 metres of
any authorised crossing.
(c) No wagon shall be moved with the help of crow bars
or pinch bars.
(7) Riding 011 locomotive, wagon or other rolling stock.
No person shall be permitted to be upon (whether inside or out·
side) any locomotive wagon or other rolling stock except where
secure foot hold and hand hold are provided.
(8) Attention to brakes and doors.-la) No locomotive,
wagon or other ro lling stock shall be kept stand ing unless its.
brakes are firmly applied and , where it is on a gradient, without
sufficient number of properly constructed scotches placed firmly
in position.
(b) No train shall be • set in motion until shunting
jamadar has satisfied himself that a ll wagon doors are securely
fastened.
(9) Projecting loads and crones.-(a) If the load on a
wagon projects beyond its length, a guard or dumnty-truck shall
be used beneath the projection.
(b) No loco-crane shall travel w ithout load unless the
job is completely lowered and positioned in line with the track.
(c) When it is necessary for a loco-crane to travel with
a load, the jib shall not be swung unt i l the loco-crane bas come
to rest.
(10) Loose shuntillg.-l.oose shunting shall be permitted
only when it cannot be avoided. ft shall never be performed on a
wagon not accompanied by a man capable or applying and pinning
down the brakes. A wagon not provided with brakes in good
working order and capable of being easily pinned down shall not
be loose-shunted, unless there is attached to it at least another
wagon with such brakes. Loose· shunting shall not be performed .
with, or against a wagon containing passengers. Jive-stock or
explosives.
( 1 1 ) Fly-shunting.-Fly shunting shall not be permitted
on any factory railway.
(12) The shunting jamadar.--(a) Every locomotive or
wagon in motion in a factory shall be in charge of a properly
trained jamadar.
1 ' [R.61L!
(b) Before authorising a locomotive or . wagons to be
moved, the shunting jamadar shall satisfy himsel.f that no person
is under or in between or in front of the locomotive or wagons.
(13) Hand signals.-The hand signals used by the shunting
jamadar by day and night shall be those prescribed by the shunting
rules of railways, working under the Indian Railways Act, 1890
(Central Act IX of 1890).
(14) Night work and fog.-(a) In factories where persona
work at night, no movement of locomotive, wagon or other
rolling stock otherwise than by hand shall be permitted between
sunset and sunrise unless the tracks and their vicinity are lighted
on a scale of not less than lO .lux as measured at the horizontal
plane at the ground level .
(b) In no circumstances shall any locomotive or train be
moved between sunset and sunrise or at any time when there is
fog, unless it carries a white head light and a red rear light.
J
( 15) Speed control. -(a) A locomotive or train shall not
be permitted to move at a speed greater than seven kilometres per
hour.
(b) A train, locomotive, wagon or other rolling stock
shall not be moved by mechanical or electrical power unless it is
preceded at a distance of not less than IO metres · during the whole
of its journey by a shunting jamadar. He shall be provided with
signalling flags or lamp and whistle necessary for calling the
attention of the driver.
(16) Tracks.-(a) The distance (i) between tracks and
(ii) between tracks and buildings, blind walls or other structures
and (iii) tracks and materials deposited oo the ground shall be
respectively not less than :-
(aa) from centre to centre of parallel tracks, the overall
width of the widest wagon of that gauge plus twice the width of
the door of such a wagon when opened directly outwards plus l
metre.
(bb) from a building or structure other than a loading
platform to the centre of the nearest track, half the overall width
of the widest wagon of that gauge, plus the width of its door when
opened outwards plus 1 .5 metres.
(cc) from material stacked or deposited alongside the
track, on the ground or on a loading platform, to the centre of the
nearest track, half the overall width of the widest wagon of that
gauge, plus half the width of its door when opened directly
outward, plus 1 metre,
-TAMIL NADU f'ACTO�IES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 [61L
(b) Sleepers of a track shall be in level with ground
and at all crossings of the track width a road or walkway, the
surface of the road or walkway shall be in level with the top of
the rails.
(c) · All track ends shall be equipped with buffer stops
of adequate strength.
(d) Barriers of substantial construction shall be se�ur�ly
and permanently fixed across any doorway or gateway in a building
or in a wall which conceals an approaching train from view,
between the building and the track as prescribed in clause (a) of
sub-rule (3). ·
(e) Where tracks are carried on a gantry, or other
elevation, a safety footway or footways w ith hand rails and toe
boards shall be provided at all positions where persons work or
pass on foot ; and where there is an opening in the stage of an
elevated fenced or the opening itself provided with a gri l l through
which a person cannot fall.
(f) All point levels shall have their movements paralled
to, not across, the direction of the track.
(g) Ail loading platforms which are more than 60 c .m .
above the level of the ground on which the track is laid and more
than 15 metres in length shall be provided with steps at intervals
not greater than 15 metres apart to enable the platform to be easily
mounted from the track.
(h) Turn tables on plant railways shall be provided with
locking devices which will pervent the tables from turning while
locomotives or wagons are being run on or off the tables.
(i) Workers shall be prohibited from passing under,
between or above railway wagons.
(17) Cro.s·sings.-(a) At all crossings of a track with a road
or walkway, danger or crossing signs and wherever reasonably
practicable, blinking lights or alarm lights shall be provided. At
all important crossings, gates or barriers manned by watchman
shall be provided. Swinging .gates and barriers shall be secured
against inadvertent ! opening or closing.
(b) All crossings, warning, signs, gates and barriers shall
be illuminated during hours of darkness.
( 18) Duties of drivers and shunters.-lt shall be the duty
of every driver of a locomotive or a shunter including a shunting
jamadar. to report without delay to the ir superior any defect in
permanent way locomotive or rolling stock.
R. 61M]
(19) Young persons not to be employed as drivers of locomotive or ·
as shunters, -- No person who is under 18 years of age and no person who
is not sufficiently competent and reliable shall be employed as a driver of
locomotive or as a shunter.
(20). The Chief Inspector may by an order in writing exempt a
factory or part of it from all or any of the provisions of this rule to such
extent and on such conditions as be deems necessary].
1[61-M. Safety Committee.--(1) In every factory--
(a) Wherein two hundred and fifty or more workers are ordinarily
employed; or
(b) which carries on any process or operation declared to be dan
gerous under Section 87 of the Act ; or
(c) which carries on hazardous process as defined under Section 2
(ch) of the Act;
there shall be a Safety Committee.
(2) The representatives of the management of Safety Committee
shall include --
(a) A senior official, who by his position in the organisation can
contribute effectively to the functioning of the Committee, shall be the
Chairman;
(b) A Safety Officer and a Factory Medical Officer, wherever
available and the Safety Officer, in such a case shall be the Secretary of
the Committee;
(c) A representative each from the production, maintenance and
purchase departments.
(3) The Workers' representatives on this Committee shall be as
equal to the number of representatives of the management, as elected by
the workers. · ·
(4) The tenure of the Committee shall be three years.
(5) Safety Committee shall meet as often as necessary but at least
once in every quarter. The minutes of the meeting shall be recorded and
produced to the Inspector on demand.
1 Subs. by G.0. Ms. No. 133, Labour &- Employment, dated 23rd April, 1991
TAMIL NADU FACTORIES RULES, 1950 ·
-. TAMIL NADU FACIORIES RULES, 1950 [R. 61 M
(6) Safety Committee shall have toe right to be adequately and
· suitably informed or-
(a) Potential safety.and health hazards to which the workers may
be exposed at work place.
(b) data on accidents as well as data resulting from surveillance of
the working environment and of the health of workers exposed to hazard
ous substances so far as the factory is concerned :
Provided that the Committee undertakes to use the data on a confiden
tial basis and solely to provide guidance and advice on measures to . im
prove the working environment and the health and safety of the workers.
_ (7) Functions and duties of the Safety Committee shall include --
(a) assisting and co-operating with the management in achieving
the aims and objectives outlined in the Health and Safety Policy of the
Occupier.
(b) dealing with all matters concerning health, safety and environ
ment and to arrive at practicable solutions to problems encountered ;
{c) creating safety awareness amongst all workers;
(d) undertaking educational, training and promotional activities ;
(e) discussing reports on safety, environmental and occupational
health surveys, safety audits, risk assessment, emergency and disaster,
manasement plans and implementation of the recommendations made in
the reports ; ·
(f) carrying out health and safety surveys and identifying causes of
accidents ; ·
(g) looking into any complaint made on the likelihood of an immi
nent danger to the safety and health of the workers and suggesting correc
tive measures ; and
(h) reviewing the implementation of the recommendations made
byit .
(8) Where owing to the size of the factory or any other reason, the
functions referred to in sub-rule (7) cannot be effectively carried out by
the Safety Committee, it may establish sub-committees as may be re
quired to assist it.]
1[61-N. Quality of personal protective equipment. ,· All personal
protective equipments provided to workers as required under any of the
provisions of the Act or the rules shall have certification by Indian Stan
dard Institute.]
2[61-0, Protective eqmpment,» The Inspector may, having regard to
the nature of the hazards involved in work and process carried out, order
the Occupier or the Manager in writing to supply to, the workers exposed
to particular hazard any personal equipment as may be found necessary.]
3[61-P, Thermic Fluid Heaters. -· (1) All heaters shall be of such
construction that coils are removable for periodic cleaning, visual inspec
tion and hydraulic test.
(2) Suitable arrangements shall be made for cooling the furnace ef
fectively in case of power failure.
(3) Before restarting the furnace, it shall be effectively purged.
(4) Velocity of flow of the thermic fluid shall not be allowed to fall
below the minimum recommended by the manufacturers while the heater
is in operation.
(5) The thennic fluid shall be circulated in closed circuit formation
with an expansion-cum-deaorator tank. This tank shall be located outside
the shed where the heater is installed.
(6) Every heater shall be provided with a Photo-register actuated
audio-visual alarm to indicate flame failure and automatic burner cut off.
(7) The stack temperature monitor-cum-controller with audio-visual
alarm shall be provided so as to warn the operator in case the outlet
temperature exceeds the specified minimum.
(8) Where inspection doors are provided on the furnace they shall
be inter-locked with the burner itself so that they cannot be opened until
burner is shut off and furnace is cooled sufficiently.
(9) All heaters shall also be provided with the following safety
devices : -- ·
(i) Level control in the expansion tank ;
(ii) temperature control of thermic fluid ;
1 _Added by G.O. Ms. No. 2223, Labour and Employment, dated the 6th October, 1988
2 Ins. by G.O. Ms. No. 1527, Labour, dated the 20th July, 1988
3 Added by G.O. Ms. No. 518, Labour and Employment, dated the 15th March, 1989.
R.61P] ' TAMIL NADU FACTORI� RULES, 1950
(iii) differential pressure switch on the outlet line of the heater
tubes; and
(iv) temperature control device for the fuel oil supply to the
burner.
(10) All devices mentioned in paragraph (9) shall have interlocking
arrangement with burner so that in case of any predetermined limits being
crossed the supply of fuel and air to burner shall automatically be cut-off.
(11) All safety interlocks when operated shall be indicated on the
control panel of the heater by a suitable audio-visual alarm.
(12) Every heater unit shall be provided as a standard accessory an
arrangement for stifling with low pressure steam or nitrogen for putting
out the fire.
(13) Electric panel for the heater shall be located near the heater but
not so close as to be exposed to spilling or leaking oil.
(14) The heater shall be located in a place partitioned off with fi�
proof material from other manufacturing activities.
(15) Explosion vent shall be so installed that release takes place at
safe location.
(16) The heater coil shall be subjected to pressure test by competent
person once atleast in every 12 months. The test pressure shall not be less
than twice the operating pressure.
(17) If repairs are carried out to the coil, it shall be tested before
taking it into use.
. _ (18) The therm ic fluid shall conform to the specifications prescribed
by the manufacturers and shall be tested by competent person for suitabil
ity atleast once in every three months period. Such test shall include test
for acidity, suspended matter, ash contents, viscosity and flash point.
(19) Cleaning of internal surface of the heater or soot and check up
of refractory surface on the inside shall be carried out every month or as
often as required dependin� upon working conditions. The coils shall be
removed and surface of the coils cleaned thoroughly once atleast in a
period of six months, The burner, nozzles, oil filters and pumps shall be
cleaned once a week during the periods of use.
(20) A separate register containing the following information shall
be maintained --
TAMIL NADU FACTORIES RULES, 1950 [ R . 6 1 P
R. 61Q] TAMIL NADU FACTORIES RULES, 1950
(i) weekly checks carried out confirming the effectiveness _of the
interlock,
(ii) weekly checks confirming that all accessories are in good state
of repairs, and
(iii) information regarding fuel oil temperature, pressure, thermic
fluid inlet/outlet pressure and temperature, fuel gas temperature, recorded
at four houri y interval.
(21) The heater when in operation shall always be kept in charge of
a trained operator].
1(61-Q. Site appraisal committee. -- (1) The State Government may
appoint a Senior Official of the Factories Inspectorate to be a member and
also function as the Secretary of the Committee. · ·
(2) No member of the Site Appraisal Committee unless required to
do so by a Court of Law, shall disclose otherwise than in connection with
the purpose of Act, at any time any information relating to manufacturing
or commercial business or any working process which may come to his
knowledge during his tenure as a Member on this Committee.
(3) Applications for appraisal of sites--
(a) Applications for appraisal of sites in respect of the Factories
covered under Section 2 (cb) of the _Act shall be _submitted to the Chair
man of the Site Appraisal Committee.
(b) The application for site appraisal along with fifteen copies
thereof shall be submitted. in the form annexed to this rule. The Commit
tee may dispense with furnishing information on any particular item in
the Application Form if it considers the same to be not relevant to the
application under consideration.
(4) Function of the Committee:--
(a) The Member Secretary shall arrange to register the applications
received for appraisal of site in a separate register and acknowledge the
same within a period of seven days.
(b) The Member Secretary shall fix up meeting in such a manner
that all the applications received and registered are referred to the Com
mittee within a period of one month from the date of their receipt.
.. 1 Ins. by G.O. Ms. No. 133, Labour and Employment, dated 23rd April 1991.
TAMIL NADU FACTORIES RULES, 1950 [R. 61Q
(c) The Committee may adopt a procedure for its working keeping
view the need for expeditious disposal of applications.
(d) The Committee shall examine the application for appraisal of a
e with reference to the prohibitions and restrictions on the location of
dustry and the carrying on of processes and operations in different areas
per the provisions of rule 5 of the Environment (Protection) Rules,
)86 framed under the Environment (Protection) Act, 1986 (Central Act
;> of 1986).
(e) The Committee may call for documents, examine experts, in
pect the site if necessary and take other steps for formulating its views in
egard to the suitability of the site.
(t) The application for Site Appraisal will be considered by the
:ommittee after obtaining Letter of Intent by the applicant from the Min
istry of Industries of Government of India before its conversion as Indus
trial Licence.
Format of Application to the Site Appraisal Committee
1. Name and address of the applicant
�
---2. Site Ownership Data -"
2.1 Revenue details of site such as Survey No. Plot No.
etc.
2.2 Whether the site is classified as forest and if so,
whether approval of the Central Government under
Section 5 of the Indian Forest Act, 1927 has been
taken.
2.3 Whether the proposed site attracts the provisions of
Section 3 (2) (v) of the Environment (Protection)
Act, 1986 (Central Act 29 of 1986). If so the nature
of the restrictions.
2.4 Local authority under whose jurisdiction the site is
located.
3. Site Plan.
3.1 Site Plan with clear identification of boundaries and
total area proposed to be occupied and showing the
officers
Typewritten text
following details nearby the proposed site.
Historical monument, if any, in the vicinity ,
Names of neighbouring manufacturing units and
human habitats, educational and training institu-
tions, Petrol Installations, storages of LPG and
other hazardous substances in the vicinity and
their distances from the proposed unit.
(c) Water sources (rivers, streams, canals, dams, wa
ter filtration plants, etc.) in the vicinity.
R, 61 Q]
(a)
(b)
(d) Nearest hospitals, fire-stations, civil defence sta
tions and Police Stations and their distances.
(e) High tension electrical transmission lines, pipe
lines for water, oil, gas or sewerage.railway lines,
roads, stations, jetties and other similar installa
tions.
3.2 Details of soil conditions and depth at which hard
strata obtained.
J.3 Contour map of the area showing nearby hillocks
and differences in levels
3.4 Plot Plan of the factory showing the entry and exit
points roads within water drains, etc.
4. Project Reports
4.1 A summary of the salient features of the project
4.2 Status of the organisation (Government, Semi-Gov
ernment, Public or Private, etc.)
4.3 Maximum number of persons likely lo be working
in the factory
4.4 Maximum amount of power and water requirements
and source of their supply
4.5 Block diagram of the buildings and installations in
the proposed supply.
4.6 Details of housing colony, hospital, school and other
infrastructural facilities proposed.
5. Organisations structure of the proposed manufac
turing unit/{ actory
TAMIL NADU FACTORIES RULES, 1950'
5.1 Organisation diagrams of -
Proposed enterprise in general
Health, Safety and Environment Protection Depart
ments and their linkage to operation and technical
departments
5 .2 Proposed Health and Safety Policy
5.3 Area allocated for treatment of wastes and effluent
5.4 Percentage outlay on safety, health and environment
protection measures
6. Meteorological data relating to the Site:
6.1 Average, minimum and maximum of-
Temperature
Humidity
Wind velocities
During the previous ten years
o.2 Seasonal variations of wind directions
6,3 Highest water level reached during the floods in the
area recorded so far
6.4 Lightening and seismic data of the area
7 Communication Links
7.1 Availability of telephone/telex/wireless and other
communication facilities for outside communication
7.2 Internal Communication facilities proposed
8. Manufacturing Process Information
8.1 Process flow diagram
8.2 Brief write up on process and technology
8.3 Critical process parameters such as pressure build
up temperature rise and run-away reactions
8.4 Other external effects critical to the process having
safety implications, such as in grass of moisture or
water; contact with incompatible substances, sudden
power failure.
TAMIL NADU FACTORIES RULES, 1950 [R. 61Q
R. 61 OJ TAMIL NADtJ FACTORIES RULES, 1950 .
8.5 Highlights of the built -in safety/pollution control
devices or measures incorporated in the manufactur
ing technology
9. Information of Hazardous Materials
9.1 Raw materials, intermediates, products and by-prod
ucts and their quantities (enclose Material Safety
Data Sheet in respect of each hazardous substance).
9.2 Main and intermediate storages proposed for raw
materials/intermediates/products/by-products (maxi
mum quantities to be stored at any time).
9.3 Transportation methods to be used for materials in
flow and outflow, their quantities and likely routes
to be followed
9.4 Safety measures proposed for -
-- handling materials
-- internal and external transportation
-- disposal (packing and forwarding of finished
products)
10. Information on Dispersal/Disposal of wastes and
Pollutants
io.t , Major pollutants (gas, liquid, solid) their characteris
tics and quantities (average at peak loads)
10.2 Quality and quantity of solid wastes generated,
method of their treatment and disposal
10.3 Air, Water and Soil Pollution problems anticipated
and the proposed measures to control the same, in
cluding treatment and disposal of effluents.]
1[11 . Process Hazard Information.
11 . 1 Enclose a copy of the report on environmental im
pact assessment
11.2 Enclose a copy of the report on Risk Assessment
Study.
1 See Errata dated 26ih May, 1992.
open or classified) reports, if any, on ac
cident situations/occupational heath hazards or simi
lar plants elsewhere (within or outside the country).
12. Information of proposed safety and Occupational
Health Measures.
12.1 Details of fire fighting facilities and minimum quan
tity of water, C02 and or other fire-fighting meas
ures needed to meet the emergencies.
12.2 Details of in-house medical facilities proposed.
13. Information on Emergency Preparedness.
13.1 On-site emergency plan.
13.2 Proposed arrangements, if any, for mutual aid
scheme with the group of neighbouring factories.
14., Any other relevant information.
[R.62
..
I certify that the information furnished above is correct to the best of
my knowledge and nothing of importance has been concealed while fur
nishing it. 1
Name and Signature of the Applicant.]
TAMIL NADU FACTORIES RULES, 1950
11.3 Published (
1(61-R. Road Safety in Factory premises. - (I) Definitions.
For the purpose of this Rule, -
(a) " Authority " means registering authority under Motor
Vehicles Act, 1988 (Central Act 59 of 1988) ;
(b) " Driver or operator " means a person authorized by the
authority to drive or operate a vehicle ;
( c) " Vehicles " means all types of vehicles including carriages
registered or required to be registered under the Motor Vehicles Act, I 988
(Central Act 59 of 1988) and rules framed thereunder and used within the
I •
factory premises.
(2) Construction and maintenance of roads and safety in
driving. - (a) Internal roads shall be soundly constructed, surfaced with
good wearing material and properly maintained.
(b) Suitable dividers shall be provided where the width of road
is I 6 metres or more.
( c) All junctions, blind comers and railway crossings shall have
necessary cautionary traffic signals displayed.
(d) The· speed limit shall be displayed at conspicuous places
such as entrance to the factory and at a distance of every 500 metres along
the roads inside the factory premises.
( e) Parking places with clear marking shall be provided at con
venient places inside the factory premises.
(f) It shall be ensured that, -
(i) no vehicle is allowed or required to enter the factory
premises unless it is duly registered with the authority ;
(ii) no drive or operator is allowed or required to drive
the vehicle inside the factory premises unless he holds a valid driving
licence ;
(iii) record of details of vehicle, driver or operator or
persons accompanying the vehicle and other information such as TREM ...
CARD, as found necessary is maintained ;
I Inserted by G.O. Ms. No. 40, Labour and Employment (M-2), dated the 29th
March, 2006.
R.61-R] T.N. FACTORIES RULES, 1950
workplace;
(iv) entry of vehicles is restricted to the necessity of the
(v) no vehicle is loaded beyond its rated capacity ; and
(vi) no person is allowed to park or stay or take rest under,
between or above the vehicle.
(g) Proper traffic signals shall be displayed at sharp turns or
' U ' turns or wherever necessary.
(h) All traffic signals, markings and cautionary notices shall
be displayed in Tamil.
(i) At blind comers, convex mirror shall be installed at
correct angle which shall reflect the movement of any incoming vehicle to
unwary pedestrian or another vehicle.
(j) While reversing the vehicle, it shall be ensured that suit
able warning is sounded and if need be another person is deployed to give
signals and clearance to the driver. J
CHAPTERV
62. Wasl1i11g facilities. - (1) This rule shall come into force, in
respect of any class or description of factories,
on such dates as the State Government may, by noti
fication in the Official Gazette, appoint in this
behalf.
Rule prescribed
under sub-section
(2) of section 42.
(2) There shall be provided and maintained in every factory for
the use of employed persons adequate and suitable facilities for washing
which shall include soap and nail brushes or other suitable means of clean·
ing and the facilities shall be conveniently accessible and shall be kept in �
clean and orderly condition.
(3) Without prejudice to the generality of the foregoing provi
sions, the washing facilities shall include -
T.N. FACTORIES RULES, 1950 [R.62
(a) a trough with taps or jets at intervals of not less than 61 cenri-
metres, or
(b) wash-basins with taps attached thereto, or
(c) taps on stand-pipes, or
(d) showers controlled by taps, or
(e) circular troughs of the fountain type, provided that the Inspec
tor may, having regard to the needs and habits of the workers, fix the
proportion in which the aforementioned types of facilities shall be in
stalled,
(f) or such other washing facilities as the Inspector may consider
sufficient and suitable in the circumstances of each case.
(4) (a) Every trough and basin shall have. a smooth, impervious sur
face and shall be fitted with a waste pipe and plug.
(b) The floor or ground under and in the immediate vicinity of
every trough, tap, jet, wash-basin, stand-pipe and shower shall be so laid
or finished as to provide a smooth, impervious surface and shall be ade-.
quately drained.
(5) For persons whose work involves contact with any injurious o•
noxious substance there shall be at least one tap for every fifteen persons ;
and for persons whose' work does not involve such contact the number of
taps shall be as _follows : --
Number of workers
Upto20
21 to35
36 to50
51 to 150
151 to200
Exceeding 200 but not exceeding 500
E
I • xceeding 500
Number of taps
1
2
3
4
5
5 plus one tap for every 50
or fraction of 50.
11 plus one tap for every 100
or fraction of 100� ,
R.62) TAMIL NADU FAC'IURIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 [R.62-8
(6) If female workers are employed, separate washing facilities
shall be provided and so enclosed or screened that the interiors are not
visible from any place where persons of the other sex work or pass. The
entrance to such facilities shall bear conspicuous notice in the language
understood by the majority of the workers" For Women only" and shall also
be indicated pictorially.
(J) The water-supply to the washing facilities shall be capable
of yielding at least 27 .3 litres a day for each person employed in the factory
and shall be from a source approved in writing by the Health Officer :
Provided that where the Chief Inspector is satisfied that such an
yield is not practicable he may by certificate in writing permit the supply of a
smaller quantity not being less than 4.5 litres per day for every person
employed in the factory.
6-2-A. All classes of factories mentioned in the schedule annexed
Rule pres
cribed under
section·43.
hereto shall.provide facilities for keeping clothing not worn
during working hours and for the drying of wet clothing. Such
facilities shall include the provision of separate rooms, bags,
lockers or other arrangements approved by the Chief Inspector
of Factories.
Glass Works
THE SCHEDULE
Chemical Works
Engineering Works
Iron and Steel Works
Oil Mills
Automobile Workshop
Dyeing Works
1[Tea Factories!
Rules made under Sections 7-A (3), 41-8 (2) and 112.
2[62-B. Health and Safety Policy. - ( I) The occupier of every
factory, except as provided for in sub-rule (2), shall prepare a written state
ment of his policy in respect of health and safety of workers at work.
(2) All factories, -
(a) covered under section 2 (m) (i) but employing less that fifty
workers;
(b) covered under section 2 (m) (ii) but employing less that one
hundred workers ;
are exempted from requirements of sub rule ( 1 ) :
'Added by G.O. Ms. No. 127, Labour and Employment (M-2), dated 31st August, 2005
(with effect from 9th November, 2005).
2 Rules 62-B to 62-T, inserted by G.O. Ms. No. 133, Labour and Employment (M-2),
dated the 23rd April, 1991 . ·
R. 62-B] TAMILNADU FACTORIES RULES, 1950
Provided that they are not covered under the First Schedule under
section 2 (cb) or carrying out processes or operations declared to be
dangerous under section 87 of the Act. .
(3) Notwithstanding anything contained in sub-rule (2), the Chief
Inspector may require the occupiers of any of the factories or class or de
scription of factories to comply with the requirements of sub-rule (1), if,
in his opinion, it is expedient to do so.
(4) The Health and Safety Policy should contain or deal wi th : --
(a) declared intention and commitment of the top Management to
hearth, safety and environment and compliance with all the relevant statu
tory requirements ;
(b) organisational set up to carryout the declared policy clearly as
signing the responsibility at different levels and ;
(c) arrangements for making the policy effective.
(5) In particular, the policy should specify the following :
(a) arrangements for involving the workers;
(b) intention of taking into account the health and safety perform
ance of individuals at different levels while considering their career ad
vancement;
(c) fixing the responsibility of the contractors, sub-contractors,
transporters and other agencies entering the premises;
(d) providing a resume of health and safety performance or the
factory in its Annual Report ;
(e) relevant techniques and methods, such as safety audits and risk
assessment for periodical assessment of the status on health, safety and
environment and taking all the remedial measures ;
(f) stating its intentions to integrate health and safety, in all deci
sions, including those dealing with purchase of plant, equipment machin
ery and material as well as selection and placement of personnel ;
(g) arrangements for informing, educating and training and retain
ing its own employees at different levels and the public, wherever
required;
(6) A copy of the declared Health and Safety Policy signed by the
occupier shall be made available to the Inspector having jurisdiction ever
the factory and to the Chief Inspector ;
TAMIL NADU FACI'ORIES RULES, 1950 [R. 62-C
(7) The policy shall be made widely known by --
(a) making copies available to all workers including contract
· workers, apprentices, transport workers, suppliers, etc. ;
(b) displaying copies of the policy at conspicuous places; and
(c) any other means of communication;
in a language understood by majority of workers.
(8) The occupier shall revise the Safety Policy as often as may be
appropriate, but it shall necessarily be revised under the following
circumstances: --
(a) Whenever any expansion or modification having implications
on safety and health of persons at work is made; or
(b) Whenever new substance(s) or articles are introduced in the
manufacturing process having implications on health and safety of per- ·
sons exposed to such substances ;
62-C. Collection and Development and Dissemination or
Information. -- (1) The occupier of every factory carrying an a hazard
ous process shall arrange to obtain development information in the form
of Material Safety Data Sheet (MSDS) in respect of every hazardous
substance or material handled in the manufacture, transportation and stor
age in the factory. It shall be accessible upon request to a worker for
reference.
(a) Every such material Safety Data Sheet shall include the follow
ing information, --
(i) The identify used on the label ;
(ii) Hazardous ingredients of the substance;
(iii) Physical and chemical characteristics of the hazardous
substance;
(iv) The physical hazards of the hazardous substance,jncluding
the potential for fire, explosion and reactivity ;
(v) The health hazards of the hazardous substance, including
signs and symptoms of exposure, and any medical conditions which· are
generally recognised as being aggravated by exposure to the substance;
(vi) The primary routers) of entry ;
(vii) The permissible limits of exposure prescribed in the Second
Schedule under section 41-F of the Act, and in respect of a Chemical not
/
covered by the said Schedule, any exposure limit used or recom
mended by the manufacturer, importer or occupier;
(v i i i ) Any · generally applicable precautions for' safe
handling and use of the hazardous substance, which are known,
including appropriate hygienic practices, protective measures
during repairs and maintenance of contaminated equipment, proce
dures for clean-up of spills and leaks ; .
( ix) Any generally applicable control measures, such as
appropriate engineering controls, work practices, or use of per
_sonal ·protective equipment;
(x) Emergency and first aid procedures;
(x i ) The date of preparation of the Material Safety
Data Sheet, or the last change to it; a�d
(xi i) The name, address and telephone number of the
manufacturer, importer, occupier or other responsible party prepar
ing or distributing the Material Safety Data Sheet who can pro
vide additional information on ·the hazardous substance and
appropriate emergency procedures, if necessary.
(b) The occupier who (sic.) obtaining or developing a
Material Safety Data Sheet in respect of hazardous substance shall
ensure that the information recorded accurately reflects the scien
tific evidence used in making the hazard determination. If he be
comes newly aware of any significant information regarding the
hazards of a substance, or ways · to protect against the hazards,
this new information shall be added to the Material Safety Data
Sheet as soon as practicable.
(c) An example of such Material Safety Data Sheet is
g iven in the Schedule to this rule.
(2) labelling. Every container of a hazardous
substance shall be clearly labelled or marked to identify:--
(a) the contents of the container;
(b) the name and address of the manufacturer or im
porter of the hazardous substances;
(c) the physical and health hazards; and
· (d ) the recommended personal protective equipment
needed to work safely with the hazardous substance.
TAMIL NADU FACTORIES RULES, 1950
1 [THE SCHEDULE
MATERIAL SAFETY DATA SHEET
I . IDENTITY OF MATERIALS:
Product Name Chemical Designation
Trade Name Synonyms
UN
Number Number
CAS
HAZCHEM
Code
Category Label:
Class
���--����������������������
Shipping Name
Codes/Label
Formula
Regulated
Identification Hazardous Waste
Identification Number
Hazardous Ingredients CAS Number
I .
2.
3.
4.
2. PHYSICAL AND CHEMICAL PROPERTIES :
Physical State ;
(Gas-, Liquid-,Solid-)
Boiling point
in degree C
Vapour pressure at 35
degree C--mm Hg.
Appearance Melting/Freezing
point in degree C
Evaporat ion rate
at 30 degree C
Odour Vapour Density (air- I ) Solubil i ty in Water at
30 degree C
I S u b s . by G . O . M ' s . N o . 222. Labour and Employment, dated t h e
2 1 s t November. 1 9 9 5 .
TAMIL NADU FACTORIES RULES, 1950
Others (corro
sivity), etc
Specific Gravity (Water- I ) PH
3. FIRE AND EXPLOSIVE HAZARDS DATA:
LEL % Flash Point
(deg.). C
Auto i gn i t i on
Temperature de
gree C
Explosion/Flammability-----------�-----
Flash Point UEL % TDC Flam-
(deg.) C m a b i I i t y
(Classific
ation)
4. REACTIVE HAZARDS:
Impact ( Hazardous Combustion products)
Stability to Stat ic Discharge (Hazardous Decomposi t ion
product)
Reactivity (Conditions to avoid)
---------------------------
Hazardous May/May not occur (Conditions to avoid)
Polymerisation
Incompatibility (Materials to avoid)
5. HEALTH HAZARDS DATA:
Routes of Entry (Inhalation, skin, mucous membranes. eye contact
and ingestion)
Effects of Exposure/Symptoms:
LD 50 (in rat)
(mg/kg body weight)
(Orally or percuta
neous absorption)
LC 50 (in rat)
(mg/1) 4/hours.
Permissible Exposure
Limit (PEL)
ppm.
mg/cu. m.
Short Term
Exposure
Limit (STEL)
ppm.
mg/cu. m.
TAMIL NADU FACTORIES RULES, 1950
Threshold Limit Value ppm.
(fl V) of ACGIH mg/cu. m.
Emergency Treatment :
6. HAZARD SPECIFICATION
Odour
Threshold
ppm.
mg/cu. m.
NFPA
Hazard
Signal Health Flammability Stability Special
Known Hazards:
Comhustible
Liquid
Flammable Material
Pyrophoric
Material
Explosive Material
Unstable Material
Water Reactive
Material
Oxidiser·
Organic
Peroxide
Corrosive Material
Compressed Gas
Irritant
Sensitizer
Carcinogen
Mutagen
Others (Specify)
'
������������������������
7, SAFE USAGE DATA:
Ventilation
Protective
Equipment
Required
Precautions
General/Mechanical
Local Exhaust
Eyes (Specify)
Respiratory (Specify)
Gloves (Specify)
Clothing (Specify)
Others (Specify)
Handling & Storage
Others (Specify)
Fire
8. EMERGENCY RESPONSE DATA :
Fire Extinguishing Media
Special procedures
Unusual Hazards
TAMIL NADU FACTORIES RULES, 1950
Exposure First Aid Measures
(inhalation, skin, eye
contact and ·ingestion)
Spills Steps to be taken
Waste Disposal Method
9. ADDITIONAL INFORMATION :
10. SOURCES USED :
Reference to books, journals, etc.
1 1 . MANUFACTURERS/SUPPLIER DATA :
Firm's Name
Mailing Address
Telephone Number
Telex Number
Telegraphic Address
Contact person in
Emergency
Standard packing
Others
Others
Emergency Telephone in Transit Areas
Acronyms- and Glc ssary of terms :
CAS : Chemical Abstract Service Registration Number.
UN Number : United Nations Number
HAZCHEM CODE : Emergency Action Code (EAC), allocated
by the Joint Conunittee of Fire Brigade Operations, UK.
TDG Flammability : Transport of Dangerous Goods -
Flammability Classification by United Nations.
TAMIL NADU FACTORIES RULES, 1950
NFPA : National Fire Protection Association, USA. LD
50 and LC 50 represent the dose in mg/kg of body weight and
the concentration in mg/I for 4 hours having lethal effect on
50% of the animals (rats) treated.
PEL Permissible Exposure Limit as laid down in the
Statutes.
TJLV : Threshold Limit Value as laid down by the
American Conference of Governmental Industrial Hygienists.
(ACGIH), USA.
STEL : Short Term Exposure Limit as laid down in the
statutes or by the ACGIH.
GUIDELINES : All efforts should be made to fill in
all the columns. No column should be left blank. In case
certain information is not applicable or available, N/APP or
NI AV sign may be used.
62-D. Disclosure of information to workers. -- ( 1 )
The Occupier of a factory carrying on a hazardous process shall
supply to all workers the following information in relation to
handling of hazardous materials or substances in the manufacture,
transportation, storage and other processes:--
(a) Requirements of Sections 41-B, 41-C and 41-H
of the Act;
(b) A hst of hazardous processes carried on m the fac-
tory;
(c) Location and availability of all Material Safety
Data Sheets as per Rule 62-B;
(d) Physical and health hazards arising from the ex
posure to or handlmg of substances;
(e) Measures taken by the occupier to ensure safety
and control of physical and health hazards;
(f) Measures to be taken by the workers to ensure safe
handling, storage and transportation of hazardous substances;
{g) Personal Protective Equipment required to be
used by workers employed in hazardous process or dangerous
operations;
TAMIL NADU FACTORIES RULES, 1950
,2-B;
(k) Role of workers vis-a-vis the emergency plan of
the factory, in particular the evacuation procedures; and
(1) Any other information considered necessary by
the occupier to ensure safety and health of workers.
(2) The information required by sub-rule ( I ) shall be
compiled and made known to workers individually through supply
of booklets or leaflets and display of cautionary notices at the
work places.
(3) The booklets, leaflets and the cautionary notices
displayed in the factory shall be in the language understood by
the majority of the workers, and also explain to them.
( 4) The Chief Inspector may direct the Occupier to
supply further information to the workers as deemed necessary.
[Rules 62E to 62G omitted by G O Ms No. 222,
Labour and Employment, dated the 21st November, 1995 J
62-H. Disclosure of information to the Chief Inspector.
1
[ ( I ) The Occupier of every factory carrying on "hazardous
process" shall furnish, in writing, to the Chief Inspector a copy of
all the information furnished to the workers.]
(2) A copy of compilation of Matenal Safety Data
Sheets in respect of hazardous substances used, produced or stored
m the factory shall be furnished to the Chief Inspector and the
local Inspector
(3) The Occupier shall also furnish any other informa
tion asked for by the Chief Inspector from time to time for the
purpose of this Act and rules made thereunder.
I Subs by G O Ms No 222, Labour and Employment, dated the
2 1 s t November, 1995
TAMIL NADU FACTOR.I.ES RULES, 1950
(h) Meaning of vanous labels and markings .used on
the containers of hazardous substances as provided under Rule
62-
(i) Signs and symptoms likely to be manifested on
exposure to hazardous substances and to whom to report;
(J) Measures to be taken by the workers in case of any
spillage or leakage of a hazardous substance;
[RuDes 62-I and 62.J omitted by G.O. Ms. No. 222,
dated the 1st November, 1995]
62-'K. InformatioBll on ][ndl111strial Wastes. -- 1 [ ( 1 ) The
information furnished under rules 62-D and 62-H shall include the
quantity of the solid and liquid wastes generated per day, their
characteristics and the method of treatment such as incineration of
solid wastes, chemical and biological treatment of liquid wastes,
and arrangements for their final disposal.]
(2) It shall also include mformanon on the quality
and quantity of gaseous waste discharged through the stacks or
other openings and arrangements such as provision of scrub
bers, cyclone separators, electrostatic precipitators or similar
such· arrangement made for controlling pollution of the environ
ment.
(3) The Occupier shall also furnish the information
prescribed in the sub-rules ( I ) and (2) to the State Pollution
Control Board.
62-L. Review of the information furnished to
workers, etc. --1
[ ( I ) The Occupier shall review once in every
calendar year and modify, if necessary, the information
furnished under rules 62-D and 62-H to the workers and the
Chief Inspector.]
(2) In the event of any change in the process or
operanons or methods of work or when any new substance is
introduced m the process or in the event of a serious accident
takmg place, the information so furnished shall be reviewed and
modrfred to the extent necessary.
62-M. Confidentiality of information. -- 1 [The Occupier
of a factory carrying on an "hazardous process" shall disclose all
information needed for protecting the safety and health of the
workers to --
( a) his workers, and
(b) Chief Inspector
as required under rules 62-D and 62-H. If the Occupier is of
the opinion that the disclosure of details regarding the pro6e§.S
I Subs. by G O Ms No. 222, Labour and Employment, dated the
2 1st November, 1995.
TAMIL NADU FACTORIES RULES, 1950
and formulations will adversely affect his business interests, he
may make representation to the Chief Inspector stating the
reasons for -withholding such information. The Chief Inspector
shall give an opportunity to the Occupier of being heard and
pass an order on the representation. An Occupier aggreived by
an order of the Chief Inspector may prefer an appeal before the
State Government within a period of thirty days. The State
Government shall give an opportunity to the Occupier of being
heard and pass an order. The order of the State Government
shall be final.]
62-N. Medical Examination. -- ( 1 ) Workers employed
in a "hazardous precess" shall be medically examined by a
qualified medical practitioner hereinafter referred to as Factory
Medical Officer, in the following manner:--
(a) Once before employment, to ascertain the physi
cal fitness of the person to do the particular job;
(b) Once in a period of six months, to ascertain the
health status of all the workers in · respect of occupational
health hazards to which they are exposed; and in c�ses where
in the opinion of the Factory Medical Officer it is necessary to
do so at a shorter interval in respect of any workers.
(c) The details of pre-employment and periodical ex
aminations carried out as aforesaid shall be recorded in the
Health Registers m Forms 39 and 17 respectively.
(2) No person shall be employed for the first time
without a Certificate of Fitness in Form 27 granted by the Factory
Medical Officer. If the Factory Medical Officer declares a person
unfit for being employed in any process covered under sub-rule
( I ) , such a person shall have the right to appeal to the Inspector
who shall refer the matter to the Certifying Surgeon whose
opinion shall be final in this regard. If the Inspector is also a Cer
tifying Surgeon, he may dispose of the application himself.
/ .
(3) Any findings of the Factory Medical Officer
revealing any abnormality or unsuitability of any person emplo
yed in the process shall immediately be reported to the Certify
mg Surgeon who shall in turn, examine the concerned worker
and communicate his findings to the occupier within thirty
TAMIL NADU FACTORIES RULES, 1950
days. If the Certifying Surgeon is of the opinion that the
workers examined is required to be taken away from the
process for health protection, he will direct the occupier accord
ingly, who shall not employ the said worker in the same
process. However, the worker so taken away shall be provided
with alternate placement unless he is in the opinion of the Cer
tifying Surgeon, fully incapacitated m which case the worker
affected shall he suitably rehabilitated.
(4) A Certifymg Surgeon on his own motion or on a
reference from an Inspector may conduct medical examination
of a worker to ascertain the suitability of his employment in a
hazardous process or for ascertaining his health status. The
opinion of the Certifying Surgeon in such a case shall be final.
The fee required for this medical examination shall be paid by
the occupier.
(5) The worker taken away from employment in any
process under sub-rule (2) may be employed again in the same
process only after obtaining the Fitness Certificate from the
Certifying Surgeon and after making entries to that effect in the
Health Register.
(6) The worker required to undergo medical examination
under these rules and for any medical survey conducted by or on
behalf of the Central or the State Government shall not refuse to
undergo such medical examination.
62-0. Occupational Health Centres. •• ( 1 ) In respect
of any factory carrying on "Hazardous process" there shall be
provided and maintained in good order an Occupational Health
Centre with the services and facilities as per scale laid down
hereunder :--
(a) For factones employing upto fifty workers --
(i) the services of a Factory Medical Officer on
retainership basts, in his clinic to be notified by the occupier.
He will carry out the pre-employment and periodical medical
examination as stipulated in 1[rule 62-N] and render medical as
sistance durmg any emergency;
I Subs by G O Ms. No 222, Labour and Employment, dated t h e '
2 1 s t November. 1 9 9 5
TAMIL NADU FACTORJES RULES, 1950
(11) a minimum of five persons trained in first-aid
procedure amongst whom at least one shall always be available
during the working period;
(i11) a fully equipped first-aid-box.
(b) For factories employing fifty-one to two hundred
workers
(1) shall have an occupational health centre It is
suggested that it shall have a room with a floor area of fifteen
square metres with floors and walls made of smooth and imper
\ ious surface and adequate rllurnination and ventilation. It is
suggested to have the equipments given in the Schedule an
nexed to this rule;
(ii) a part-time Factory Medical Officer shall be in
overall charge of the centre who shall visit the factory atleast
twice in a week and whose services shall be readily available
during medical emergencies;
( i i i ) one qualrfred and trained dresser-cum-com
pounder on duty throughout the working period;
(iv) a fully equipped first-aid box m all the depart-
men ts.
/
(c) For factories employing above two hundred
workers --
(i ) orre full time Factory Medical Officer for fac
l?nes employmg r up to five hundred workers and one more
Med ica l Officer for every add i t ional thousand workers or part
thereof ;
(ii) shall have an Occupational Health Centre. It is
suggested that it shall have two rooms with a floor area of fif
teen sq metres with floors and walls made of smooth and im
pervious surface and adequate illumination and ventilation. It is
suggested to have the equipments given in the Schedule an
nexed to thrs rule;
( 1 1 1 ) there sha l l be one nurse, one dresser-cum-com
pounder and one sweeper-cum-ward boy throughout the working
period;
,.
TAMIL NADU FACTORIES RULES, 1950
(iv) the Occupational Health Centre shall be suitably
equipped to manage medical emergencies;
(2) The Factory Medical Officer required to be ap
pointed under sub-rule ( I ) shall have qualifications included in
the Schedules to the Indian Medical Degrees Act, 19 16 (Central
Act VII of 19 16) or in the Schedules to the Indian Medical
Council Ace, 1956 (Central Act 102 of 1956) and possess a Cer
tificate of Training in -Industrial Health of minimum three
months duration recognised by the State Government :--
Provided that --
(i) a person possessing a Diploma in Industrial
Health or equivalent shall not be required to possess the certifi
cate of training as aforesaid;
. .
(11) the Chief Inspector may, subject to such condi-
trons as he may specify, grant exemption from the requirement
of this sub-rule, if in his opinion a suitable person possessing
the necessary quahfrcation is not available for appointment,
(111) in case of a person who has been working as a
Factory Medical Officer for a period of not less than three
years- on the date of commencement of this rule, the Chief In
spector may, subject to the condition that the said person shall
obtain the aforesaid certificate of training within a period of
three years, relax the qualification.
(3) The syllabus of the course leading to the above
certificate, and the organisations conducting the Course shall be
approved· by the Directorate-General of Factory Advice Service
and Labour Institutes or the State Government m accordance
with the guidelines issued by the DGFASLI.
, .
( 4) Within one month of the appointment of a Factory
Medical 'Officer, the occupier of the factory shall furnish to the
Chief Inspector the following particulars ·--
(a) °ii-Tame and address of the Factory Medical Officer;
(b r Qualifications,
(�) Experience, if any; and
(d) the sub-rule under which appointed.
TAMIL NADU FACTORIES RUL.b:::,, 1950
THE SCHEDULE
SUGGESTIVE LIST OF EQUIPMENT FOR
OCCUPATIONAL HEALTH CENTRE IN FACTORIES
I . A glazed sink with hot and cold water always
available.
2. A table with a smooth top at least 180 cm x 105 cm.
. .
3. Means for sterilizing instruments.
4. A couch .
5 . Two buckets or containers with close fitt ing l ids .
6. A kettle and spirit stove or other suitable means or
boi l ing water.
7 . One bottle of spirit ammonia aromatics ( 120 m l . )
8. Two medium size sponges.
9. Two "Kidney" trays.
I 0. Four cakes of toilet , preferably antiseptic soap.
1 1 . Two glass tumblers and two wine glasses.
1 2 . Two cl in ica l thermometers.
1 3 . Two teaspoons.
1 4 . Two graduated ( 120 ml . ) measuring glasses.
1 5 . One wash bottle ( 1000 cc) for washing eyes.
1 6 . One bottle (one l itre) carbolic lotion I in 20.
1 7 . Three chairs .
1 8 . One Screen.
1 9 . One electr ic hand-torch.
20. An adequate supply of tetanus toxoid .
2 1 . Coramine l iqu id (60 rn l . )
22. Tablets -- antis istaminic antispasmodic (25 each.)
23 . Syringes with needles - 2 cc . , 5 cc. and 1 0 cc .
24. Two needle holders, big and· smal l .
TAMIL NADU FACTORIES RULES, 1950
25. Suturing 'needles and materials
26. One dissecting forceps
27. One dress m forceps
28. One scalpel.
29. One stethoscope
30. Rubber bandage -- pressure bandage
3 1 . Oxygen cylinder with necessary attachments.
32. One Blood Pressure Apparatus.
33. One Patellar Hammer.
34 One Peak-Flow meter for lung function measurement.
35. One stomach washout.
36. Any other equipment recommei ded by the Factory
Medical Officer according to SJ - c r f i c need relating
to manufacturing process.
37. In addition :--
( I ) For Factories ,employing fifty one to two hundred-
I Four plain wooden sphnts 900 nm x 100 mm x
6 mm,
'
2. Four plain wooden splints 350 nm x 7'3 mm x
6 mm;
3. Two plain wooden splmts 250 mm x 50 mm x 12
mm;
4.0ne pair artery forceps,
5. Injections -- morphia, pethidine, atropine,
· adrenaline, coramme, novocain (2 each);
6. One surgical scissor;
(2) For Factones employing above two hundred workers --
1 . Eight plain wooden splints 900 mm x I 00 mm x
6 mm;
2. Eight plain wooden splints 350 mm x 75 mm x
6 mm;
3. Four plain wooden splints 250 mm x 50 mm x 1 2
mm:
TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950
4. Two pairs artery forceps;
5 . Injections -- Morphia, pethadine, atropine,
adrenaline, cerarni ne , novacain (4 each);
6. Two Surgical scissors.
62-P. Ambulance Van. -- ( I ) In any factory carrying
on "hazardous process" there shall be provided and maintained
in good condit ion , a suitably constructed ambulance van
equipped with item as per sub-rule (2) and manned by a
full- t ime Driver-cum-Mechanic and a Helper trained in first-aid
for the purpose of transportation of serious cases of accidents
or sickness. The ambulance van shall not be used for any
purpose other than the purpose stipulated herein and will
normally be stationed at or near to the Occupational Health
Centre :
Provided that a factory employing less than two
hundred workers, may make arrangements for procuring such
facility at short notice from a nearby hospital or other places.
to meet any emergency.
(2) It is suggested that the ambulance may have the
fol lowing equipments : - -
(a) General --
A wheeled stretcher with folding and adjusting
devices with the head of the stretcher capable of
being tilted upward;
Fixed suct ion uni t with equipment;
Fixed oxygen supply with equipment;
Pillow with case; Sheets; -- Blankets -- Towels;
Emesis bags; Bed pan ; -- Urinal; -- Glass;
(b) Safety equipment --
Flares with life of thirty minutes; Flood lights;
Flash lights ; -- Fire Extinguisher dry powder
type; Insulated gauntlets;
(c) Emergency Care Equipment
(i) Resuscitation --
Portable suction unit; portable oxygen units;
' Bag; -- · Valve; -- Mask; -- · Hand operated
artificial ventilation unit ;
Airways; -- Mouthgags; -- Tracheotomy adapters;
Short spine board; I.V. Fluids' with administration
unit;
B.P. Manometer -- Cugo; -- ;Stethoscope;
'·
( i i ) Immobilization --
Long and short padded boarks_; -- Wire ladder
splints;
Triangular bondage Long and short spine
boards; .,
( i i i ) Dressings
Gauze pads -- 4 x 4; -- Universal dressing IO x 36;
Roll of aluminium foils; + soft roller bandages
6 x 5" yards Adhesive tape in 3 " rol l ;
Safety pins ;
Bandage Sheets; Burn 'she et :
( iv) Poisoning --
Syrup of lpecae; Activated charcoal pre-packeted
in dozes;
Snake bite kit;
Drinking Water;
(v) Emergency Medicines
As per requirement (under . the advice of Medica l
Officer only)
62-Q. Decontamination facilities. -- In every factory,
carrying out hazardous process the following provisions shall be
made to meet emergency :--
(a) Fully equipped first-aid box;
(b) readily accessible means of water for washing by
workers as well as for drenching the clothing of workers
who have been contaminated with hazardous · and corrosiv,.e
substance ; and such means shall be as per the scale shown in
the Table below :--
TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950
THE TABLE
Number of Persons employed
at any time
( 1 )
( i) Upto 50 workers
(ii) Between 5 1 to 200 workers
( i i i ) Between 201 to 500 workers
( iv ) 501 workers and above
Number of
drenching showers.
(2)
2
2 + 1 for every addi-
tional 50 or part
thereof.
5 + I for every addi-
tional 100 or part
thereof.
8 + I for every addi-
tional 200 or part
thereof.
(c) A sufficient number of eye wash bottles fil led
with dis t i l led water of suitable l iquid kept in boxes or cup
boards conveniently situated and clearly indicated by distinctive
s ign which shall be vis ible at all times.
62-R. Making available Health Records to Workers.
( I ) The Occupier of every factory carrying out an
"hazardous process" shall make accessible the health records
including the record of worker's exposure to hazardous. process
or, as the case may be, the medical records of any· worker for
his perusal under the following conditions:--
(a) Once in every six months or immediately after
the Medical examinat ion whichever is earlier;
(b) If the Factory Medical Officer or the Certifying
Surgeon as the case may be is of the opinion that the worker
has manifested signs and symptoms of any notifiable disease as
specified in the Third Schedule of the Act;
(c) If the worker leaves the employment;
(d) If any one of the following authorities so direct -
An inspector notified under the Act;
District Health Officer;
The Commissioner of Workmen's Compensation;
The Director-General, Employees' State
Insurance Corporation;
The Director, Employees' State Insurance
Corporation (Medical Benefits); and
The .Director-General, Factory Advice Service
and Labour Institutes .
(2) A copy of the upto-date health records inc luding
the records of worker 's exposure to hazardous process or as the
case may be, the medical records shall be supp l ied to the
worker, on receipt of an application from h im . X-ray plates and
other medical diagnostic reports may also be made available for
reference to his medical practitioner .
62-S. Qualifications, etc., of Supervisors. -- ( I ) All
persons who are required to supervise the handling of hazar
dous substances . shall possess the following qualifications and
experience ;
(a) (i) A degree in Chemistry or Diploma in Chemical
Engineering or Technology with five years experience; or
( i i) A Master 's Degree in Chemistry or a Degree
in Chem ical Eng ineering or Technology with
two years experience .
The exper ience st ipulated above shall be in process
operation and maintenance in the Chem ical Industry.
(b) Chief Inspector may require the supervisor to un
dergo training in Health and Safety.
TAMIL NADU FACTORIES RULES, 1950
(2) The syllabus and duration of the above training
.he organisations conducting the training shall be approved
re Director-General, Factory Advice Service and Labour In
es or the State Government in accordance with the
rlines issued by the Director-General, Factory Advice Ser
and Labour Institutes.
62-T. Issue of guidelines. -- For the .Purpose of
ihance with the requirements of sub-sections (1) , (4) and (7)
ection 41-� and Section 41-3 (sic.) of the Act, the Chief
:ctor may if deemed necessary, issue guidelines from time to
to the occupiers of factories carrying one 'hazardous
sss' . Such guidelmes may be based on National Standards,
s of Practices or recommendations of International Bodies
as International Labour Organisation and World Health
rnsation.]
63. First-aid Appliances. -- In every factory there shall
.rcvided and maintained by regular replenishment first aid
es or cupboard/s distmctively marked with a red cross on a
� background 1 [and it is suggested that the first aid boxes or
oards are equipped] with the contents as per the appropriate
specified in the following Table for the corresponding class
actories A, B or C, as indicated below · --
lass - A.
lass - B
lass - C.
.(i) All factories under section 85 (i) of the
Act, and
(ii) Factories under section 2 (m) (ii) of
the Act, employing up to fifty workers.
Factories under section 2 (m) (1) of the
Act employing up to fifty workers.
Factories under section 2 (m) ( i ) or 2 (m)
( i i) of the Act emp loy ing more than fifty
workers.
I Subs by G 0. Ms No. 1 5 0 (Labour and Employment) dated the
July, 1 9 9 3 ] �
TAMIL NADU FACTOR.IES RULES, 1950
TAMIL NA.DU FACTORll!S Ruus, 1950 {R. 63
THE TABLE
(Specifying the scale of contents with which each first-aid box
or cupboard is to be equipped)
( l)
Contents
(2)
Quantity or number
applicable to Factories in
r=>: ·- ---.A.-----�
Class A Class B Class C
(3) (4) (S)
Copy of First-aid leaflet
issued by the Directorate·
General of Factorv Advice
Service and Labour ·Institutes,
Government of India, Bombay,
2 Scissors.
3 Snake-bite lancet.
4 Tablet (each of 5 grains of
aspirin or any other analgesic).
5 Bottle of Pottassium Permanga
nate crystals.
6 Bottle of Salvolatile having the
dose and mode of administra
tion indicated on the label.
7 Bottle of Contrimide solution
(1%) or a suitable antiseptic
solution.
8 Bottle of Mercurochrome solu
tion (2%) in water.
9 15 gm. packet of sterilised
cotton wool.
lO Adhesive Plaster (2cm. X l m.)
11 Adhesive Plaster (6 cm. x l m.)
12 Small size sterilised dressing
or adhesive wound dressing
approved by the Chief
Inspector.
13 Medium size sterilised dressing
or adhesive wound dressing
approved by the Chief
Inspector.
6
3
1 2 24
12
]
1
l
JOO 100 100
Tablets Tablets Tablets
30ml. 30 ml. 30 ml.
30 ml . 60 ml. i20 ml.
60 ml. 120 ml. 200 ml.
60 ml. 120 ml . 200 ml .
3 6 12
I roll 2 rolls 2 rolls
1 roll
R. 63] TAMIL NADU FACTORIBS RULES, 1950
{I)
Contents
(2)
Quantity or number
applicable to Factories in
,.-- -- __ ..,.._ __ ----�
Class A Class B Class C
(3) (4) (5)
14 Large size sterilised dressing or
adhesive wound dressing
approved · by the Chief
Inspector.
15 Large size sterilised burn
dressing.
16 Sterilised eye pad in a sealed
packet.
17 Polythene wash bottle (i litre
or. 500 cc.) for washing eyes.
18 Tourniquet
19 Safety pins.
20 Roller bandage S cm. wide.
21 Roller bandage 10 cm. wide.
12 Triangular bandage.
23 Plain wooden splint
353 mm. x 75 mm. X 6 mm.
24 Plain wooden splint
900 mm. X 100 mm. X 6 mm.
25 Plain wooden splint
250 mm. X 50 mm. X 12 mm.
26 · Kidney tray.
3
3
6
1
6
6
8
1
l
1 Dozen
12
12
12
1
1
2 Dozens
12
12
6
6
6
3
1
l[Provided that each first-aid box or cupboard shall also
contain such other equipment or medicine as the Chief Inspector
may deem essential and direct in writing, from time to t ime:
Provided further that in a factory where a properly equipped·
ambulance room or dispensary is provided and maintained under
rule 64 or if dispensary or hospital is available within one kilo
metre of the precincts of a factory and such arrangements are made
I Subs. by G.O. Ms. No.150, Lab.&., Emp. (tvl-11), dated the 14th July, 1993.
TAMIL NADU FACTORIES RULES, 1950 [R.. 64
by the Occupier as to ensure the imn.1e�iate treatment therein of �II
injuries sustained by a worker within the . factory, . the Chief
Inspector mar by an order i� writing, relax the requ�rem.ents of
this rule, subject to such conditions as he may specify m that
order.]
63-A. Notice regarding first-aid.-ln every factory, a
prominent notice containing the following particulars shall be
displayed at some conspicuous and convenient place at or near the
main entrance to the factory-
(a)' the location/s of the first-aid box/es or cupboard/s in
the factory ;
(b) the name and designation of the responsible person
working within the precincts of the factory who is trained in first
aid treatment and who is separately incharge of each of the above
first-aid box/es or cupboard/s;
(c) the work-room or place where each such person shall be
available during the working hours of the factory ; and
(d) the name of the nearest hospital and its telephone
number.
Copies of the above notice shall also be displayed at a conspi
cuous place near each first-aid box or cupboard.
. 1[63-B. First-aid.-Persons who are in charge of first-aid
,box shall be persons who possess the certificate granted by the
Saint John's Ambulance Association for rendering first-aid.]
64. Ambulance room.-( 1) The ambulance room shall be
separately situated from the factory premises. It shall be kept
open when any work is being carried on in the factory and shall be
·. used only for the purposes of first-aid treatment and rest. It shall
have a floor area of at least 24 square metres and shall be adequ
ately ventilated and lighted by natural and artificial means. The
floor and walls shall be smooth, hard and impervious. '[There
shall be attached to it at least one latrine and urinal of sanitary
type].
(2) An adequate supply of wholesome drinking water shall
be provided in the ambulance room which shall also contain at
least-
I Ins. by G.O. Ms. No. 2013. Lah & Emp . . dated the 30th August, I 980.
2 Ins. hy G.O. Ms. No. I 09, La hour. dated the 23rd January, I 91<5.
(i)
(ii)
(iii)
(iv)
(v)
(vi)
(vii)
One screen;
A table with a smooth top at least 180 cm. X 105 cm. ;
Three chairs ;
A couch;
Two stretchers ;
A glazed sink with hot and cold water always avai
lable;
Two buckets or containers with close fitting lids ;
(viii) A kettle and spirit stove or other suitable means of
boiling water;
(ix)
(x)
(xi)
(xii)
{xiii)
(xiv)
(xv)
(xvi)
(xvii)
(xviii)
(xix)
(xx)
(xxi)
(xxii)
(xx iii)
(xxiv)
(xxv)
(xxvi)
(xxvii)
(xx viii)
(xxix)
(xxx)
(xxxi)
(xxxii)
(xxxiii)
(xxxiv)
Means for sterilising instrument;
Two rubber hot water bags;
Six woollen blankets;
Six hand towels;
Four cakes of antiseptic soap ;
Two medium size sponges ;
A stethoscope:
Two clinical thermometers;
One electric hand torch ;
Four kidney trays ;
Two glass tumblers ;
Two wine glasses ;
Two graduated measuring glasses (120 ml.j ;
Two mini-measuring glasses ;
Two teaspoons ;
One wash bottle (1,000 cc ) for washing eyes:
Three surgical scissors ;
Three pairs of artery forceps ;
Three dissecting forceps ;
Three dressing forceps ;
Three scalpels;
Needle holder ;
Syringes with needles : 2 cc., 5 ce., 10 cc., and 50 cc. ;
Suturing needles and materials;
Rubber bandage-Pressure bandage ;
Twelve plain wooden splints, 350 mm. x 75 mm. x
6 m m . ;
a, 64] TAMIL NADU FACfORIES RULf!S, 1950
TAMIL NAOU FACTORll!S R.ULtS, 1950 [R. 64
(xxxv) Twelve plain wooden splints 900 mm. x 100 mm. x
6 m m . ;
(xxxvi) Six plain wooden splints 250 mm. X SO mm. X
12 mm. ;
(xx.xvii) An adequate supply of antitetanus toxiod;
(xxxviii) One bottle (120 ml.) of Sprruus Ammoniae Aroma
ticus ;
(xxxix) Smelling salts (60 gm . ) ;
(xi) Tablets: Anithistamine, Antispasmodic (25 each) ;
(xli) One bottle (one litre) carbolic lotion I in 20;
(xiii) Coramine liquid (W ml.);
(xl i i i) Injections; Morphia, pethedinc, atropine, adrenaline,
coramine, novocaine (6 each);
(xliv) Oxygen cylinder with necessary attachments ;
(xiv) Four first-aid boxes or cupboards stocked to the scale,
specified for Class C under Rule 63.
(3) The ambulance room shall be in-charge of a qualified
medical practitioner assisted by at least one qualified nurse and
such staff as the Chief Inspector may deem necessary and direct in
writing from time to time.
Explanatlott.-« For the purpose of this sub-rule, the expression
"Qualified Medical Practitioner" means a person holding a quali
fication granted by an authority specified in the schedule to the
Indian Medical Degrees Act, 1 9 1 6 (Central Act VII of 1916), or in
the schedule to the Indian Medical Council Act, 1956 (Central Act
102 of 1956).
(4) A prominent notice containing the following particulars
shall be displayed at a conspicuous place in the ambulance room:--
(a) the name, address and telephone number of the
medical practitioner in charge; and
(b) the name of the nearest hospital and its telephone
number.
(5) The occupier of every factory to which sub-section (3)
of section 45 of the Act and this rule (Rule 64) apply, shall make
all necessary arrangements for the expeditious removal in a
suitable conveyance of serious cases of accident or sickness in the
factory for further treatment to the nearest Government or other
hospital. where the requisite facilities for the further treatment of
such cases are available. ·
(6) The Chief Inspector may, by an order in writing,
exempt any factory from the requirements of this rule, subject to
R. 65) TAMI[, NADU FACTORIES RULES, 1950
such conditions as he may specify in that order. if a properly.
equipped dispensary .or hospital is available at or within one kilo
metre of the precincts of the factory and such arrangements are
made by the occupier as to ensure the immediate treatment therein',
of all injuries sustained by workers within the factory and for pro
viding rest to the injured workers.
65. Canteens.-(1) Rules 65 to 71 shall come into force in
respect of any class or discription of factories on
1[Rules 6� to such dates as the State Government may, by notifi·
71 prescribed · , h Offi · 1 G · t · th· under sections. cation ID t e era azette, appom an 1:1
46 and I J2J. behalf.
(2) The occupier of every factory notified by the State
Government and wherein more than two hundred and fifty workers
are ordinarily employed shall provide in or near the factory an
adequate canteen according to the standards prescribed in these
rules.
(2-A} In factories in which workplaces are situated at a
distance of more than 0.2 km. from the canteen and · where the
Chief Inspector directs in writing, arrangements shall be made for
serving light refreshments from the canteen to workers at the work-
1"J�es.
(3) The sroccupier or Manager of a factory] shall submrt
for the approval of the Chief Inspector plans and site plan, in
triplicate, of the building lo be constructed or adapted for use as a
· canteen.
(4) The canteen building shall be situated not less than
15.2 metres from any latrine, urinal, boiler house, coal stacks, ash
pumps and any other source of dust, smoke or obnoxious fumes :
I Provided that the Chief Inspector may in any particular
factory relax the provisions of this sub-rule to such extent as may
be reasonable in the circumstances and may requite measures to be
adopted to secure the essential purpose of this sub-rule.
(5) The canteen building shall be constructed in accordance
with the plans approved by the Chief Inspector and shall accom
modate at least a dining hall, kitchen room, pantry and washing
places separately for workers and for utensils. The minimum
height of the building shall be not less than 3.7 metres and all the
walls and roof shall be of suitable beat-resisting materials and shall
be water-proof
1 Subs. by G. o. Ms. No. 109, Labour, dated the 23rd Jam(ary, 1985.
2 Sub&, by G.O. Ms. No. 2013, Labour and Employment. dated tt,c
30th August, 1980.
(6) In a canteen the floor and inside walls upto a height of
1 .2 metres from the floor shall be made of smooth and impervious
materials ; the remaining portion of the inside walls shall be made
smooth by cement plaster or in any other manner approved by the
Chief Inspector.
(7) The doors and windows of a canteen building shall be
of fly-proof construction and shall allow adequate ventilation.
(8) 'Ihe canteen shall be sufficiently lighted at all times
when any persons have access to it.
(9) (a) In every canteen-
(i} all inside walls of rooms and ceiling and passages
and staircases shall be limewashed or colourwashed at least
once in each year or painted once in three years dating from the
period when last limewashed or painted, as the case may be ;
(ii) all wood work shall be varnished or painted once
in three years dating from the period when last varnished or
painted ;
(iii) all internal structural iron or steel work shall be
varnished or painted once in three years dating from the period
when last varnished or painted :
Provided that inside walls of the kitchen shall be limewashed
once in every four months ;
(b) Records of dates on which limewashing, colour
washing, varnishing or painting is carried out shall be maintained
. · in the prescribed register (Form No. 7).
(10) The precincts of the canteen shall be maintained m a
clean and sanitary condition. Waste water shall be carried away
in suitable covered drains and shall not be allowed to accumulate
so as to cause a nuisance. Suitable arrangement shall be made for
the collection and disposal of garbage.
66. Dining hall.-(1) The dining ball shall aacommodate
at a time at least 30 per cent. of the workers working at a time :
Provided that, in any particular factory or in any particular
class of factories, 1(the Chief Inspector of Factories may, by an
order in writing] in this behalf, alter the percentage of workers to
be accommodated.
(2) The floor area of the dining hall, excluding the area
occupied by the service counter and any furniture except tables and,
chairs, shall be not less than 0.9· square metre per diner to be
accommodated as prescribed in sub-rule (1).
1 Subs. b) 0.0. Ms. No. lC.9, Labour,dated the 23rd January. 1985.
TAMIL NADU FACTORIES RULES, 1950 [R. 66
R. 67A]
be partitioned off and reserved for women workers in proportion
to their number. Washing places for women shall be separate and
screened to secure privacy.
(4) Sufficient tables, chairs or benches shall be. avail�ble for
the number of diners or accommodated as prescribed in sub·
rule ( I ) :
Provided that where the Chief Inspector is satisfied that
satisfactory alternate arrangements are made, he may exempt any
particu Jar factory or class of factories from the provisions of this
sub-rule.
(5) Soaps and towels should be provided at the washing
places in the canteen for the use of the workers.
67. Equipment.-()) There shall be provided and main·
tained sufficient utensils, crockery, cutlery, furniture and any other
equipment necessary for the efficient running of the canteen, Suita
ble clean clothes for the employees serving in the canteen shall also
be provided and maintained.
(2) The furniture, utensils and other equipment shall be
maintained in a clean 'and hygienic condition. A service counter,
if provided, shal l have a top of smooth and impervious material.
Suitable facilities including an adequate supply of hot water shall
be provided for the cleaning of utensi ls and equipment.
(3) Food and food materials should be stored in fly-proof
safe and handled with the help of wooden ladles or suitable metal
forceps whichever is convenient. Vessels once used should be
scalded before being used again.
67-A. Medical examination of Canteen Staff.-Every mem
ber of the canteen staff who handles foodstuffs shall be medically
examined by the Factory Medical Officer or the Certifying Surgeon
and such examination shall include the following, namely:-
(i) Routine and bacteriological testing of faeces and urine
for germs of dysentery and typhoid fever at intervals of not more
than six months ;
(ii) Routine blood examination at intervals of not more
than twelve months;
(iii) Any other examination including chest X-rays that
may be considered necessary by the Factory Medical Officer or the
Certifying Surgeon. Any person, who in the opinion of the Factory
Medical Officer as confirmed in writing by the Certifying Surgeon,
rs unsuitable for employment on account of possible risk to the
health of others, shall not be employed as canteen staff.
TAMIL NADU FACTORIES RULES, 1950
(3) A portion of the dining hall and service counter shall
TAMIL NADU FACTORIES RULES, 1950 [R.69
(b) Such charges shall be paid by the occupier into the local treasury
and the receipt attached with the application.]
3((c) The certificate of Medical Examination of Canteen Staff shall be
issued in Fonn No. 40.)
68. Prices to be charged. - (I) Food, drinks and other items served in the
canteen shall be served on a non-profit basis and the prices charged shall be subject
to the approval of the Canteen Managing Committee. In the event of the Committee
not approving the price list or where the Committee are equally divided on the issue,
the price list should be sent to the Chief Inspector for approval.
4((1-A) In computing the prices referred to in sub-rule (1), the following
items of expenditure shall not be taken into consideration, but will be borne by the
occupier:-
( a) the rent for the land and building ;
(b) the depreciation and maintenance charges of the building and
equipment provided for the canteen ;
(c) the cost .of purchase, repairs and replacement of equipment
including furniture, crockery, cutlery and utensils ;
(d) the water charges and expenses for providing lighting and
ventilation ;
(e) the interest on the amount spent on the provision and main
tenance of the building, furniture and equipment provided for the canteen ;
(f) the cost of the fuel required for cooking or heating food-stuffs or
water; and
(g) the wages of the employees serving in the canteen and the cost of
uniforms ;'if any, provided to them. J
(2) The charge per portion of foodstuff, beverages and any other item
served in the canteen shall be conspicuously displayed in the canteen.
69. Accounts. - (I) All books of accounts, registers and any other
documents used in connection with the running of the canteen shall be produced on
demand to an Inspector of Factories.
(2) The accounts pertaining to the canteen shall be audited,
once in every twelve months, by registered accountants and
auditors. The balance-sheet prepared by the said auditors SQ.!1.11 be submitted
I Ins by GO. Ms. No 1568, Labour, 1st August, 1985.
3 Added by GO. Ms. No 127, Labour 'and Employment (M-2), dated 31-8-2005.
4 Ins. by GO. Ms. No. 2013, Labour and Employment, 30th August, 1980.
1((iv) (a) The fee for such routine clinical examination of each member of
the canteen staff by the certifying surgeons shall be 2(f200/- (Rupees two hundred
only)] which fee is exclusive of any charges incurred for conducting any kind of
Laboratory tests, etc.
2 Subs. by GO. Ms. No 132, Labour and Employment (M-2), 28t September, 2018.
to the Canteen Managing Committee not later than two months -
after the closing of the audited accounts :
Provided that the accounts pertaining to the canteen in a
Government Factory having its own Accounts Department may be
audited in such Department.
7@. Managing Committees.-(i) The manager shall
appoint a Canteen Managing Commitee which shall be consulted
from time to time as to-
(a) the quality and quantity of foodstuffs to be served in
the canteen ;
(b) the arrangements of the menus;
(c) times of meals in the canteen; and
(d) any other matter as may be directed by the Committee.
(2) The Canteen Managing Committee shall consist of an
equal number of persons nominated by the occupier and elected by
the workers. The number of elected workers shall be in-the pro·
portion of onefor every 1,000 workers employed in the factory,
provided that in no case shall there be more than five or less than
two workers on the Committee and in cases where the workers
refuse 'lo elect their representatives, the occupier shall himself
nominate the worker's representatives.
(3) The occupier shall appoint' from among the persons
nominated by him, a Chairman of the Canteen Managing
Committee.
(4) The manager shall determine and supervise the proce
dure for elections to the Canteen Managing Committee.
(5) A Canteen Managing Committee shall be dissolved by
the manager two years after the last election, no account being
taken of a by-election or its constitution, as the case may be.
(6) Where the workers of a factory in which a canteen has
been provided by the occupier in accordance with rules 65 to 67 for
the use of the workers, desire to run the canteen by themselves on
a co-operative basis with share capital contributed by themselves,
the management may permit them to run the canteen in accordance
with the by-laws of the Co-operative Canteen, the Madras Co-ope·
rative Societies Act, 1932*, and the rules framed thereunder, subject
to such conditions as the Chief Inspector may. in consultation with
the Registrar of Co-operattve Societies, Madras, impose .
. (7) The provisions of sub-rule ( I ) of rule 68, sub-rule (2)
of rule '69 and sub-rules ( I) to (S) of rule 70 shall not apply to
• Now the Tamil Nadu Co-operative Societies Act, 1983.
a. 70) TAMIL NADU fACTORDES R.IULl!S, 19S0
TAMIL NADU FACTORll!S RULES, 1950 [R. 72
canteens which are run on co-operative basis by the workers
themselves and which are recognized by the Chief Inspector.
7U. The provisions of rules 65 to 70 may be relaxed by tl�e
Chief Inspector, subject to such conditions as he may deem fit, m
the case of factories belonging to the same business groups or
amalgamation where centralized cooking in an approved !i�dust�ial
canteen is arranged for. Adequate arrangements to the satisfaction
of the Chief Inspector shall, however, be made in such cases for
the conveyance and proper distribution of the food so cooked to
the workers concerned as if separate canteens had actually been
provided at site in the factories covered by this relaxation.
72. Shelters, rest rooms and lunch rooms.-(!) This rule
. shall apply to any factory wherein more than
Rules prescr�bed one hundred and fifty workers are ordinarily
under l[secuons
47 and 112]. employed.
(2) The shelters, or rest rooms and lunch rooms shall
conform to the following standards and the 9[0ccupier or Manager
of a factory] shall submit for the approval of the Chief Inspector
plans and site plans in triplicate of the building to be constructed
or adapted :-
(a) The building shall be soundly constructed and all
the walls and roof shall be of suitable heat-resisting materials and
shall be water-proof. The floor and walls to a height of 9 1 .4
centimetres shall be so laid or finished as to provide a smooth, hard
and impervious surface.
(b) The height of every room in the bu i lding shall be not
less than 3. 7 metres from floor level to the lowest part of the roof
and there shall be at least 1 . 1 square metres of floor area for every
person employed : Provided that (i) workers who habituatly go
home for their meals during the rest periods may be excluded in
-calculating the number of workers to be accommodated and (ii)
m the case of factories in existence at the date of commencement of •
the Act, where it is impracticable, owing to Jack of space to provide
1 . 1 square metres of floor area for each person, such reduced floor
area per person shall be provided as may be approved in writing bv
the Ch ief Inspector. ·
(c) Effective and suitable provision shall be made in
every room for securing and ma intaining adequate ventilation b�
the circulation of fresh air and there shall also be provided and
maintained sufficient and suitable natural or artificial lighting.
l Added by G.O. Ms. No. 109, Labour, dated the 23rd January, 1985.
' Subs. by G.O. Ms. No. 2013, Labo�r and Employment, dated the
.�Otb August, 1980,
(d) Every room shall be adequately furnished with chairs
or benches with back-rests.
. (e) Sweepers shall be employed whose primary duty it is
.to keep the rooms, building and precincts thereof in a clean and
tidy condition.
' '[(ee) suitable provisions shall be made in every room for
supply of drinking water and facilities for washing ]
(f) The Chief Inspector may, for reasons to be recorded
in writing, relax the provisions of this rule subject to such condi
tions as he may deem fit to impose, in respect of factories in exis
tence on the Isl April, 1949.
2((3) A portion of the shelters or rest rooms and lunch
rooms shall be partitioned off and reseryed for women workers in
proportion to their strength ]
73. Creches.-(1) Rules 73 to 76 shall apply to any factory
wherein more than 3[lbirty women workers] are ordinarily
employed.
R u le pres·
cribed under sub·
section (3) of sec·
tion 48 5[and sec·
lion 112],
(2) The creches shall conform to the
following standards and the �(Occupier or
Manager of the factory] shall submit for approval
of the Chief Inspector, detailed plans in triplicate
of the building to be constructed or adapted.
(3) The creche shall be conveniently accessible to the
mothers of the children accommodated therein- and so far as is
reasonably practicable it shall not be situated in the close proximity
to any part of the factory where obnoxious fumes, dust or odours
ate. given off or in which excessively noisy processes are carried on.
(4) The building i n . which the creehe is-situated shall be
soundly constructed and all the walls and roof shall be of suitable
heat-resisting materials and shall be water-proof. The floor and
internal walls of the creche to a height of 1 .2 metres all-round shall
be so laid or finished as to provide a smooth impervious surface.
(S) The height of the rooms in the building shall be not less
than 3. 7 metres from the floor to the lowest part of the roof and
there shall be not lsss than 1.9 square metres or floor area for each
child to be accommodated.
1 Ins. by G.O. Ms. No. 109, Labour, dated the 23rd January, 1985.
II Ins. by G.O, Ms. No. 2743, Labour. 27th December, 1984.
a Subs. by G.O. Ms. No. 2013, Labour. and Bmployment, dated the
30th August, 1980, for " fifty women workers ••.
' Subs. by G.O.Ms. No. 2013, Labour and Employment, dated the
30th August 1980.
II Added by G.O. Ms, No. 109, Labout, daded the 23rd January0 !911S.
R, 73] · TAMIL NADU FACTORIES RULES, 1950
TAMIL NADu FACIORIES RULES, 1950 [R. 75
(6) Effective and suitable provision shall be made in every
part of the creche for securing and maintaining adequate ventilation
by the circulation of fresh air.
(7) The creche shall be adequately furnished and equipped]
and in particular there shall be one suitable cot or cradle with the
necessary bedding for each child (provided that for children over
two years of age it will be sufficient if suitable bedding is made
available) at least one chair or equivalent seating accommodation
for the use of each mother while she is feeding or attending to her
child and a sufficient supply of suitable toys for the older children.
(8) A suitably fenced and shady open air playground shall
be provided for the older children :
Provided that the Chief Inspector may by order in writing
exempt any factory from compliance with this sub-rule if he is
satisfied that there is not sufficient space available for the provisionv,
of such a playground. I
74. Wash B'Oom.-There shall be in or adjoining the creche a
suitable wash room for the washing «f the children and their .
clothing. The wash room shall conform to the following
standards :-
(a) The floor andinternal walls of the room to a height of
91.4 centimeres shall be so laid or finished as to provide a smooth
impervious surface, The room shall be adequately lighted and
ventilated and the floor shall be effectively drained and maintained
in a clean and tidy condition.
(b) There shall be at least one basin or similar vessel for
every four children accommodated in the creche at any one time
together with a supply of water provided, if practicable, through
taps from a source approved by the Health Officer. Such source
shall be capable of yielding for each child a supply of at least
22. 7 Ii tres of water a day.
(c) An adequate supply of clean clothes, soap and clean
towels shall be made available for each child while it is in the
creche,
(d) Adjoining the washing room referred to above; a
septic type latrine shall be provided for the sole use of the children
in the creche. The design of this latrine and the scale of
accommodation to be provided shall be determined by the Health
Officer. The creche latrine shall always be kept clean and in a
sanitary condition by a sweeper specially employed for the purpose.
75. Supply of miiBk and refreshment.-At least 284.1 milli
litres of clean pure milk shall be available for each child on every
day it is accommodated in the creche and the mother of such. a child
\ '
R. 76A] TAMIL NADU FACTOIUES RULES, 1950
shall be allowed in the course of her daily work, intervals of at
least 15 minutes to feed the child. For children above two years
of age there shall be provided in addition an adequate supply of·
wholesome refreshment.
76. Creche staff and clothes for creche staff.--(1) The
occupier shall appoint a qualified nurse or midwife with sufficient
number of ayahs, the number calculated at the rate of one ayah for
every 30 children or part thereof for the purposes of looking after
the children accommodated in the creches and the occupier shall
provide suitable equipment and the facilities for the purpose :
Provided that the occupier may appoint a nurse or midwife
who is not qualified if the Chief Inspector, in consultation with the
Director of Medical Services, certifies that such nurse or midwife is
suitable for appointment under this sub-rule.
(2) The creche staff shall be provided with suitable clean
clothes by the occupier for use while on duty in the creche.
1[76-A. Exemption from the provisions of creche.--(1) In
factories where the number of married women or widows employed
does not exceed 15 or where the factory works for less than 180
days in a calendar year, or where number of children kept in the
creche was less than 5 in the preceding year, the Chief Inspector
may exempt such factories from the provisions of section 48 and
rules 73 to 76 if he is satisfied that alternate arrangements as
stipulated under sub-rule (2), are provided by the factory.
(2) (a) The alternate arrangements required in sub-rule (1)
shall include a creche building, which has a minimum accommo
dation at the rate of 2[ 1.9 metre] per child and constructed in
accordance with the plans approved by the Chief Inspector.
(b) The creche building shall have--
(i) a suitable wash room for washing of the children and
their clothing ;
Ins. by G.O. Ms. No. 1536, Lab. & Emp. dated the 19th
September, 1979.
- Subs. by G.O. Ms No.109, Labour, dated the 23rd January, 1985
[R.76A
(ii) adequate supply of soap, clean clothes and towels
and
(iii) adequate number of female attendants who are
provided with suitable clean clothes for use, while on
duty, to look after the children in the creche.
1[(2-A) (a) If factories or group of factories or cluster of
factories in an area which are statutorily required to provide a
creche, decide by mutual agreement among themselves to provide a
common creche in the form of a group or chain of creches, within
one kilometre radius from such factories and to share the
expenditure and maintenance in the running of such common creche
facilities, proportionate to the number of eligible children, such
factories may apply to the Chief Inspector in writing for grant of
exemption from providing a separate creche. The Chief Inspector
may exempt such factories from providing' f1 separate creche, subject
to such conditions as he may deem fit, affh satisfying himself that
the alternate arrangements are adequate and appropriate to meet the
needs of all the eligible employees in such factories ;
I
(b) Where the factories in an �rea, on payment of
contribution proportionate to the number qf the eligible children,
avail the common crech.e facilities provicf�? by the promotional
institutions such as Small Industries Development Corporation, State
Industries Promotional Corporation of Tamil Nadu Limited or by the
Employers' Association or by voluntary organisations aided by the
State Government or Central' Government, suck factories may apply
to the Chief Inspector in writing for grant of exemption from
providing a separate creche. The Chief Inspector may exempt such
factories from providing a separate creche, subject to such
conditions as he may deem fit, after satisfying himself that the
alternate arrangements are adequate and appropriate to meet the
needs of all the eligible employees in such factories:}
I
(3) The exemption granted under sub-rule 11) may at any
time be withdrawn by the Chief Inspector if he finds after such
enquiry as he may deem fit, that the factory has committed a
breach of this rule.]
1 Ins. by G.O. Ms. No. 116, Lab. & Emp. (M-11) dated the 28th
June, 1994.
TAMIL NADU FACTORIES RUI_.ES, 1950
R.78] THE TAMIL NADU FACTORIES RULES, 1950
CHAPTER VI
Working hours of adults
77. Compensatory lto/idays. - (1) Except in the case of workers
engaged in any work which for technical reasons must be carried on
Rules prescribed continuously throughout the day, the compensatory
under sub-section holidays to be allowed under sub-section (1) of section
(2) of section 53 52 of the Act shall be so spaced that not more than two
holidays are given in one week.
(2) The Manager of the factory shall display, on or before the end
of the month in which holidays are lost, a notice in respect of workers
allowed compensatory holidays during the following month and of the dates
thereof, at the place at which the Notice of Periods of Work prescribed
under section 61 is displayed. Any subsequent change in the notice in
respect of any compensatory holidayshall be made not less than three days
in advance of the date of that holiday.
_ (3) Any compensatory holiday or holidays to which a worker is
entitled shall be given to him before he is discharged or dismissed and shall
not be reckoned as part of any period of notice required to be given before
discharge or dismissal.
(4) 1[(a) The manager shall maintain the details of compensatory
holidays in the Muster Roll in Form No. 25.)
(b) The register maintained under clause (a) shall be preserved
for a period of three years after the last entry in it and shall be produced
before the Inspector on demand.
78. Muster-roll for exempted factories. - The Manager of every
factory in which workers are exempted under section 64 or 65 from the
M u s t e r . r O 1 1 provisions of section 5 1 or 54 shall keep a muster
prescribed under roll in Form No. 10 showing the normal piece-work
sub-section (5) (b) rate of pay or the rate of pay per hour of all exempted
of section 59 employees. In this muster-roll shall be correctly
entered the overtime hours of work and payments therefor of all exempted
workers. The muster-roll in Form No. 10 shall always be available for
inspection.
I Subs. by Gd. Ms. No. 121, Labour and Employment (M-2), dated the 31st July,
2012.
78-A. Metl,od of calculating cas/1 equivalent 011 account of
concessionai sale of foodgrains and other articles. - (i) The cash
Rules prescribed equivalent of the advantage accruing through the
under sub-section concessional sale to a worker of foodgrains and other
(5) of section 59 articles shall be computed at the end of every wage
period fixed under the provisions of the Payment of Wages Act, 1936.
(ii) For the purpose of computing cash equivalent of the advantage
accruing through the concessional sale to a worker of foodgrains and other
articles, the difference between the value of foodgrains and other articles,
at the average market rates prevailing during the wage period in which
overtime was worked and value of foodgrains and other articles supplied
at concessional rates shall be calculated and allowed for the number of
overtime hours worked :
Provided that this rule shall not apply to any railway factory whose
alternative method of computation has been approved by the State
Government.
78-B. Overtime slips. - Period of overtime work shall be entered
in the overtime slip in duplicate and a copy of the slip signed by the
Manager or by a person authorised by him shall be given to the worker
immediately after the completion of the overtime work :
Provided that the Chief Inspector may by order in writing exempt
any factory or class of factories from the provisions of this rule,
subject to such conditions as he may impose, if he is satisfied that any
alternative system followed therein, is adequate to meet the requirements
of this rule.
78-C. Restriction of double employment. - An adult worker may
be employed, in more than one factory on the same day, with the
Rule under previous approval of the Inspector, subject to the following
section 60. conditions : -
( 1 ) He shall not be employed for more than nine hours in all on
anyone day.
(2) He shall receive a weekly holiday in accordance with the
provisions of section 52.
(3) Every worker who is required to work in another factory on
the same day shall carry with him a card in which the following particulars
shall be entered by the Manager of the first factory :
THE TAMIL NADU FACTORIES RULES, 1950 [R.78-C
(a) His normal periods of work as the notice of period of
work, for the day.
(b) The period or periods he has worked in the first factory
for the day.
The Manager of the second factory in which he is to work for the
rest on the day shall enter in the card the period or periods he has worked
for the day in his factory. The Manager of both the factories in which the
worker has worked for the day on the same day shall send to the Inspector
an extract of the card mentioned above not later than three days from the
date on which the worker has so worked in the two factories on the same
day.
79. Notice of periods of work. - The notice of periods of work
for adults required under sub-section (1) of section 61 of the Act and
the notice of periods of work for children required under sub-section
ll) of section 72 of the Act shall be in Form No. 1 1 and shall be
iqisplayed in a conspicuous place at or near the entrance to the factory
, IMSth in English and Tamil.
ltegister Prescribed 80. 1[Register of adult workers and young
under sub-section (2) persons]. - The Register of adult workers shall
of section 62. be in Form No. 12.
2[81. Persons defined to hold position of supervision or
management. -(a) The following categories of persons shall be deemed
to hold position of supervision or mangement : -
I Subs. for" Register of adult workers", by G.O. Ms. No. 121, Labour and
Employment (M-2), dated the 31st July, 2012.
2 Inserted (sic) by G.O. Ms. No. 217, Labour and Employment (M-2), dated the
29th July, 2004 (for Gazette extract, see Digest of Labour Cases, 2005 at p. 14).
R.81] THE TAMIL NADU FACTORIES RULES, 1950
R. 82J TAMIL NADU FACTORIES RULES. 1950
-,
( ] ) Directors.
(2) Managers ,
(3) Assistant Managers ;
(4) Engineers.
(5) Weaving Masters and Spmnmg Masters ,
(6) Head Electncians ;
(7) Labour Welfare Officers ;
(8) Chief Chemist ;
(9) Chief Metallurgists;
(10) Chief Production Engineers;
(11) Work Superintendents ;
(12) Chief Security Officers ;
(13) Fire Officers ;
(14) Chief Accounts Officers ;
(15) Chief Personnel Officers ;
(16) Chief Public Relations Officer;
(17) Foreman;
(18) Chargeman;
(19) Chief Draftsman;
(20) Head Sto1�-Keepers;
(21) Safety Olhcers ;
(22) Human Resources Development Officers ,
(23) Quality Assurance Personnel ,
(24) Sales Pcrvonnel ,
(25) Material Issue Personnel : and
(26) Systems Analysts 01 Operators in Eleen omc Data P1 occssing
Section.
lb) Any other person, who, Ill the opinion of the Chief Inspector
ol Fuctoriev, hold, position of supci vision or management
82. Persons employed in a confidential position. - (a) The following
categones of persons shall be deemed to be employed in confidential
positions . -
( I ) Stenographers ;
(2) Personal Assistants or Secretaries of Managers of Factories ;
(3) Time-Keepers ;
( 4) Telephone Operators ,
(5) Personnel Officers ;
(6) Human Resources Development Personnel ;
(7) Security Officers ;
(8) Industrial Engineers ;
(9) Quality Assurance Personnel ;
( 10) Sales Personnel ;
( 1 1 ) Material Issue Personnel ; and
(12) Systems Analysts or Operators in Electronrc Data Processing
Section.
(b) Any other person, who, in th� opinion of the Chief
Inspector of Factories, is employed in confidential position.
83. List to be maintained of persons holding confidential
positions or supervision or management. - A hst showmg the names
and designations of all persons to whom the provision of sub
section ( 1 ) of Section 64 have been applied shall be maintained in every
factory.
84. Exemption of certain adult workers. - (a) Adult workers engaged
m factories specified m Column (2) of the Schedule to this Rule on the work
specified m Column (3) thereof shall be exempted from the provisions of
the Sections specified in Column (4) subject to the conditions, if any,
specified m Column (5) of the said Schedule. -
(b) Except m the case of urgent repairs covered by item ( 1 ) of the
Schedule, the exemptions shall be subject to the following conditions,
name ly·-
(1) m case of exemption from Sections 5 1 and 54, no worker shall
work for more than ten hours per day or 56 hours per week ,
R. 84] TAMIL NADU FACTORIES RULES, 1950
(2) in case ot exemption from Section 55, sufficient lime, though
not a fixed period, shall be given for meals to the satisfaction of the Inspector
of Factories concerned ,
(3) in case of exemption from Section 56, the spread over of hours
of work inclusive of mtervals for rest shall not. exceed twelve hours in any
one day; and
(4) the total overtime hours worked beyond the limits of nine
hours per day and 48 hours per week shall not exceed 50 hours for such
quarter of the calendar year.
(c) In the absence of a worker who has failed to report for duty in
factories in which any work should be earned on continuously for
technical reasons, a shift worker be allowed to work the whole or part of
the subsequent shift Irrespective of the restrictions imposed in
Clauses (i) and (11) of sub-section (4) of Section 64 of the Act ; Provided
tha t :- ·
(I) the next shift of the shift-worker shall not commence, before
a penod of eight hours has elapsed ;
(2) within 24 hours of the commencement of the subsequent shift
notice shall be sent to the Inspector, explaining the circumstances under
which the worker rs required to work in the subsequent shift ; and
(3) the exemption will be restricted to only male adult workers.]
I
1[84A. Exemption of women workers. -All women working in fish-
curing and fish-cannmg factories shall be exempted from the provisions of
sub-section ( I ) of section 66 of the Act, subject to the following conditions,
namely-
( I ) No woman shall be employed before 6 a.m. or after 7 p.m. for
more than three days in any one week. The number of days on which a
woman may be so employed shall not exceed fifty in a year;
(2) No woman shall be employed after I _I p.m. and before 5 a.m.;
(3) A period of uninterrupted rest of atleast rune hours
shall intervene between the cessation of penod of work after 7 p m on any
_ day. and the begmning of a fresh penod of work on the following day ;
awl ·
(4) A muster-roll m Form No 25-A shall be mamtamcd j
I Ins by G O M� No 367, Labour, dated the 23rd February, 1985. (for Gazette
extract see 1985 Digest of Labour Cases at p 13).
TAMIL NAOU FACTORIES RULES. 1950 [R. 84-A
[84 B. Guidelines for the employment of women in night shifts.-(1) It
shall be the duty of the occupier of a factory, to take all steps to prevent the
commission of the acts of sexual harassment in the factory;
(2) The occupier of a factory shall maintain a complaint mechanism in
the factory itself and to dispose of the complaints in time bound manner
with strict confidentiality, by constituting a complaint committee which
shall consist of such members, headed by a woman familiar with the
issues of sexual harassment and not less than half of its members should
be women besides a non-governmental organisation's representation;
(3) The women workers shall be allowed to raise the issue of
sexual harassment in the workers' meeting;
(4) The occupier of a factory shall take all necessary steps to assist the
women workers affected by sexual harassment;
(5) The occupier of a factory shall provide proper lighting in and
around the factory;
(6) The occupier of a factory shall ensure that women workers
employed in night shift shall not be less than ten and not less than two
third of the total strength of workers and one third of the Supervisors /
Shift Incharge / Foremen shall be women; as well;
(7) The occupier of a factory shall provide sufficient women security at
the entry and exit points and sufficient work sheds for the women workers
be employed in night shift;
(8) The occupier of a factory shall provide separate dining
facility and separate safe transportation from the factory premises to the
nearest point of their residence to the women workers in night shift;
(9) The occupier of a factory shall provide necessary medical facilities
and also make these facilities available at any time of urgency in case of
injury or incidental acts of harassment, by providing necessary telephone
connections;
_________________________________________________________________
1Ins. by G.O. Ms. No. 61, Labour and Employment (M2), 3rd April 2017.
(10) The occupier of a factory shall ensure that wherever the factory
provides boarding and lodging for women workers, the same shall be kept
exclusively for women and it should be under the control of women
wardens or supervisors;
(11) The occupier of a factory shall ensure that there shall not be less
than twelve consecutive hours of rest between the last shift and the night shift
whenever a woman worker is changed from day shift to night shift and from
night shift to day shift;
(12) The occupier of a factory shall appoint not less than two women
workers per night shift who shall go round and work as Special Welfare
Assistants;
(13) Whenever there is any untoward incident, the occupier of a factory
shall send a report to the Inspector and Police Station concerned as well;
(14) The occupier of a factory shall exhibit these guidelines in a
prominent place so that the women workers can be aware of their rights;
(15) Adequate toilet with water facility, shall be provided to the women
workers, conveniently situated and easily accessible containing all basic
amenities and safety measures to the workers;
(16) Creche facility wherever needed, shall be provided to the women
workers for the care of their children with care taker with all essential
amenities].
Sanction oflhlAc! empower--ing the gml uaftlxgmpr‘iml.
l 3 3
64 (2}(n) All
and 540) “cm“
Class o
fkcwm Name aflhe exempted warki
J Urgeru IcpairsExplnnnrian. — The follow‘ng shnll beconsidered (a he urgcm repairs :—nepnirs In any pan o
r
rhe machinery,plantar srrnczure o
f
factory w ' h are o
lsuch n nnmre Hm delny in their execurmnwould invulvi: dungcr in human lirc orsolely or
lh: smppagc o
f
mnnulncruringprocess.
(i)
Bltnldnrwn repairs |n mauve pawel nmsmlsslnn
m orher Essenrial plat“ o
f orher lac-loner.collrerien Railways. Mnlnr Transpmls,DnL yards. Horhourn Gas Elecmcal Generahngnnn Tradxrnis‘innx Pumymg or
similar erremial
or
Pub] Ulillly Semces carried our in
Ihegulcral Engineering Works and Foundries and
w ch era nccnssm In
enable such concerns Inmammi rhen rm manufacturing prooeaa.pmduclinll or
service dunng nnn'nnl walkinghours urnconrding m Schedule. ‘
(b)
w
1
9
P
“?
9
5
‘5
5
‘17:
'1
:
'l§
5
“
film
s
‘7
5
‘2
5
'ls
w
o
w
s
THE SCHEDULE
Brim o
fa‘xrmprion.
'I9
P
U
'9
5
‘5
S
(I)
(iv)
(I)
(ii)
Remark:
5
No worker shall he employed lor more than IShour: on any one day. 39 hours during any
rhrecconsecurivc dnyn or
no hauls during each ptl'indeafseven conseeulive days mmmnncirlg fmm hm hmemployment :wuhin 24 hours o
f
lhe commencemenl o
l
mework. norice shall he senr m the lnspczmrdescnmng lhe nnlure o
f
the nrgenl repmrs and theperiod probably rcquilcd fur rheir complexionExemplion mun me pmvlsmns or Sccllun 54 shallapply only in WC ens: o
!
male adulr warkclse
A running record o
f
work done on
such repnir: shallhe mnlnrnlned in |he Mnsrer Roll in Form No.25A vid: Rule 103%,
No worker snnll hr:
employed for mam lhnn 15hours on nny one day 39 hours during any
rhreeconsccutwe days or
so hours during each period o
fseven consecuuvn days commencing [mm In:
rimemploymenl :
wirhin 24 hours or me commencemenr o
f
mework, norlee shnll be seal lo lhe lnspeemr
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
IE
S
R
U
L
E
S
.
I9
5
0
describing the nnrnre a
!
rhe urgcnl repnrrs and rhe_period prchooly required fol melt complexion. .3
5
1
m Repmls \0
new in ships and repairs lo ‘
mmeré’lnlalrcmhs dun n lnclcry which we.
csseulial m 5mm]:
such slnpa or
mama to
lnava pan a
l
pmper ulna mcannnne \hclr nannal npenuulls, Ill
sun on
Iirwonhy:nndlhuns, n5
Lh: case may )2:
all
lupans m Cunumunn wllh a
change o
f mullv: pawn,
lm cxample. mun swam ll:
elecmclly. m v
' *e
warm
when aucn wnrk :nnnol possibly be Llama willlomnappage ar lna nonnal naannrannxlng pram
Explnna. . —
rel-m cal
clcnmng .5 non
included ln
Ih
mnna " cxamlnmg " or
" repmnng .
4
SwimsSI,
52‘
54‘55,
55 mm
m
(in)
(M
(i)
(h)
‘I9
(ul)
(ivl
ru
m
9
;
’s
s
'v
S
‘L
S
‘ls
N
e
w
s
lil
m
)1
9
P
‘"
Am
9
5
'5
5
'v
s
‘Z
S
’ls
s
u
m
m
s
5
Exemption (mm the
pmmlanl n
r
Stcliml 54 sh I
apply only
ln
m: can In
!
mull: Idullw rs:
A lnnnlng aemnl alwork dam: on
aacn mpnn: 5n
be ma 7
ulnarl in ma Muslur nan ln
Farm Mal
25-A n
‘ e
Ruin In -A.
Na worker shall be
employed fol more man l5 lnnna an any
one
a
ll
39 hours annng any
(hm: leMH—‘ullvc days or
ea
hours a mg
ml. ulna D'stmzn consul-MW: anys
commencingfrom lug my amp aymnnl ;
wlmln 24 hauls o
f
m
:
cunmmcamanwr llw.
walk, nollan shall
bl:
scnl ln lna
Illsymlordesu‘hmg me name arm: Ulgam mpfifi
and ma
pan-x) pmbanly rcqulrefi [at
man complclmn.Excmpllnn from lhcdpmwsinllfi n
r
Scanan 54 shall apply only
"I
the cast o
f
mle n
uh workels .
A run ng
recnrd a
!
walk done an
such lepnlls shall h: mmna
xulnbd m lha MIlsler Roll n
l
ann No. 13A vnla Ru]: KELA
Na wnrknr shzlll be
employed rm mm man 1
5
hams an any
on:
day
39
hours durlng any
man mnseculiva days on
56
hours L‘mlng Each panad n
l
val/2n collmlnive y~
mmmcnemglmm lns first nnaploynn-nl .
wllhln 14 hours arm: cumnllmmmelu quh: wnrk, nunca shall
b
: sum lo the
lnspcclnnkscnblng the mum fifth: urge!“ lapairs
nlld "It
pcnnd pmbnbly requirtd fur than manplanon.Excmylivn rmm nan
pnwls a
l
Sannan 54 allall Ipply only
m m :35: nfmala ndnll wnrkcr‘ ,
a mulling realm} a
r
wnrk am an
inch mpails shall be.
main-Iunad ill
(h: MHSICY Rnll lrl
Form Na Zi-A vidt Rah: |D3<Al
3
5
2
T
A
M
IL
N
A
U
U
F
A
C
T
U
R
IF
R
R
H
I
w
:
ll-
lif
l
7
G
F
A
J
}
(a
!
N
ru
m
(q
)
(:7
v
9
9
5
1
0
1
:”
"
V
I
.
Work in m: machlm shop. our
mm, nr
the laundryrm m lgurrrrg are an: :dnvmgof gr.
gnppmams. Ibemmhrmical m alum 4
mu M II": sienm rrr wamr pipes or pumrrs o
f
Ihr:
fnclnry
Walk nfcxnxmnln or
rcpairing any
machinery nrpm I :p 1w ichmlxcccsmryfnrcnnymga rmwork rum-curry.
mm and Engine mnms‘ suL murdcr w rarsr ileam nr gulznne gusprcpnmmry w m: unmmnnccl vinyl-r work m
m: may.
I9
v
"
!
9
5
'5
9
‘V
S
‘1
9
s
n
o
w
s
P
M
9
5
‘
‘5
;
‘v
s
"L
s
m
a
m
a
s
w
:
'1
;
s
u
o
m
a
s
'1
9
I
9
?
“
9
5
‘5
';
(i)
5
Nu worker shall be arrrployrn [on more than 15 hours an anyrule day, 39 hours dunng My mm canseculive days nr
56hnurs rtrrnrrg anch period o
f seven (msacuuvc days mmmenulngrrrrrrr h
'
Tun employmenl .
04 hams aflhe commancermm a
t
me work. nolic: 5r.be sun 0 m
:
lnspacmt ducnbmg Ill: "mun: o
r
an urge!“ anirs
u
Lhe period probably leq
‘rca fnrflmlr mmpxrnurr.Examplmn from me p vmmu «We: 54 gm app‘y my
in
me we o
f
mi: adu x
workers,
A
r mng mcord a
f
work dune on such mpam shall b
: mmnrForm No zs-A id: Rm: 103%
Nu wnrkcl mu m :m Jnycd rrrr mam um 15 ham on anymu: m, 9 hnurs dunng rrry
um :nnszcmlve days at
51>hams dunngmh :n'od uneven cmsrcnuw days commencingfrom his firsl
cmprbymem ;
w mu 4 hours 01m: mmmuuumm oflh: vmrk. noun: mu1m 1h: (nspu. or
rum-r ng
m: nah": r
!
rm mgnntrvpmrsand «Mr
prrrrra pmbflbly uq
11d rrrr
murcompleLionrExamplmn lmm Um p
r
III
Eh: case c
f
male adul
A running record o
f
waxk done a such rcpails shall hr. m-ulainzd m
: Musmr In M Farm Nor H-A dz mar XOR-A
No wurkcr mu m ampluycd rrrr mart [hm [s hnurx all myan: army 39 bouts during any
mm» cansccuhv: days ar
anbums dm' gmh mind mun. rurrmununayscummzncmgrrurrr h
l
rm
zlnproymcm :
w in 24 how aim: commencement o
r
urr
wzxk. none: muhe mu m we [115mm dascnbmg Ihu nnlure arm: urgrrrr lepnmImd m: prnoa probnbly required rar
rhrr’rcrrrrrpleaon
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
|E
S
R
U
L
E
S
,
1
9
5
0
3
5
3
1 2
3
4
Salinas 51.
54>
55.
$6 and 61.
a Clerks engaged in the prepmxinn afpny mus. Seeuunr 5x.
54.and 56.
Crnernn sumo. Wurkufi Shnwing mfleclors. shifting fumiluunn selclnp swim 5
.boys, crrrnerernen and sound depm-menr men rn the 55‘
55 m. M
process o
f
shaming films.Brendan m
drsmenrling a
f
swings nr
(h:
mnkc up
n
f
Secunns 5
actors and annulus in Chxzmn studio. 55,
56 and 5
Swim! 51.54.“55,
55 and 51.
cinema 5
lmn. Sum Brass Walk in cunnwlinn mm mllchnnging.
gums. venljlaung Sncfions 51.
54.55,
56 an
1
.
Work perfumed by
drivers..na humidifying appernnrs Sections 5 SJ.2
.
Walk rrernued b
y
fire pum men.W P 55.
56 and a
mrdamnm. Sealinns “ 56
andSemen: 55.
56
end 61Secljnns 55.
55
Ind 51.
Cmdamun rau-aria.
Work a
t persmls ernpmyea rn
u
m
m
P
“!
1
3
]
(1
)
v
9
sm mm. All
wmknrs nmplnycd in me
manufanur: nrd=spatch
Dirndl conversion(Blnckgmn) {new
n‘es and olhcr dhall{mm-in
Work n
f persons nmpluyw in drymg Blnckgnm ind
peal g
me skin (If
bmken rim."
5
Eszplimx from me provrsinns n
f
Secrran :4 sumnpply unly in me me o
f
male adnlr warm;
(iv)
A running recerd o
f
war]: dunc an
such rep r
:71
be
minrnined rn
me Mnszerknu in Farm 0
.ZS-A Me Rule IDEA.
The exfimpfinn mu he
only hr the
prapmfinn a
f pay
m r.
(n Exem ‘nn from me movisiuns a
f seerran a
]apply in so
tar as
i
t
[chm lame xpedficnion on a
mud erresr inmrvn! In are neuee ulvmd: perm
a!
mm
3
5
4
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
IE
S
R
U
L
E
S
.
I9
5
0
5
Ging M
y
0r](chekku CmnmyExpexers.
An nduh workers engaged in rnrrnnrrrernrrngpmccss.
Seclinns and 6
!
m
(2)
The speed avrr :hnll nor
exceed melve hamsMy
day nre cnuics mgard g numnl rarrrrnerreenrand mmplerion on pmnds 1:!
work emu b
lentered in Farm No. zs—A.
nr
:dulLs.
Tlre sprend nvor emu nm excud rwelve harm on
any
day.
Th: ennres regerarng new earnnrenumenrand mmplehnn o
r
merr pen‘rnls a
t
work shall heunwed m Form No. 25A.
an (1)(cl
News paperPresser
Work nrperenr ernproyea m the rerrery, mnchina5mm hm nrrdprrreesrnepnmnrn .
Sam nr
51,54(”6.
'(
c
ir
w
w
m
m
lw
Erecrnuere mg andan nrrm i
r
r
gsmians
a) Sngnr fumes,
(3)
Chemical f
atlas.
a
)
Vegemhlcyarngennrrme nus
(5)
ice lucmnuv
Ail wurkus engaged in no rnnerrgerrer ngnnransfnrmmgolEle
AH workers engaged in wnmmou! process work
An werkere engaged in
ennrinnrnrs pmeeee work
All
worker: engrrgerr in :nnunnrnrr rrmeerr wan
Au workers engaged in conrrnrrens pmcas work
Scdmm 52.
54.55 md 6L
Sudan: 52 54
55.
56 and 6
5:: ans 5:,
54.
55 and 6L
Such-ms 52 M
,55 end
arenrprrnn ham the mo
' ' rrs
ofxcc ‘orr
6
1 win Ipplyin en
far
er'
mrnrer (u
rrre spaclfinmmn n
f
rhe pcnoderreer rnrerv me mum a
t
work period for
mine
— 53m: x;
nhuv: —
4 same u nbrrve 4
v “me n:
nhovn 4
-—§nmc us
nhrrve ——
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
IE
S
R
U
L
E
S
,
1
9
5
0
355
3
5
6
2 3
4 5
(m on M 5
.
All walkfli Engaged in mminunm Sulmm 52,
54 ermplmn {mm "m pmvlsions n
r xacllon 61 will applyproceis wnrkv 55 and u
l
in so
muluelales lo
um spmficazm n
l
lhe palmnflcslinurvnl in m: mule: alwnm pmnd rm mum
us
ubav: 4 — sum: as
abnvc 7 4 sum: as
nlm: —v:73 Roller FlourMills
(K)
Glass facmnas — Sam: as
Ihove ! - sum: as
nbnvcg ——~ sum: as
nlme —
(9)
Pam lanolin — slum: as
above 4 45-1": as
nhnvc —— is above —
HG) Rnbblzr Tyne All
walkers an
lb: curing process. —SIl|I= as
abov: 7 — sum: IS
abov: —(“Kc-Hts.
u I
)
Ccmcnl lacl- A“ Wm; my“. in cam-m"; —flme as
Ibovc 4 v mm: as
abav: i
miss proccss worm
— sum: as
above 4 —s:m= ns
nbuva g - sauna 15
mm —
new 5
:
pumping — sum: as
above 4slaljans.
(13) Tammie: Cunnlry and Cllrfmlc m ing Batman: 52,
54,
—~samz :15
abavl: —exclndlng mu finishmg p
l
ass,
57 ml 6x
(14) Brick. [jigs Wark. ulkiln bunlersl — same as
dumb; —s:lme :15
above,—
ka m m: slill Ind condensing Vsnmxnsnbava— —sm:lsabov=4
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
IE
S
R
U
L
E
S
,
1
9
5
0mums.
a
:
flu-mu enmllug x‘nnms. —La.mc n:
lbw: 4 ~ same I!
above 4
massing 4mm as
lhov: v _SW ,5
"mm ..
I 2
UK) Chicm’y 1
. nuts
(19) [mm Sxezl EmsCup}: 'and Alum
«1
m
l ng
miHs.
x
e dyemg (am
nu man—paw)
(2!) on mnk insunaniun
(22) AH {admins
123) All lemme:
(>4 (3)-
Work o
f persons tagged in mepmeesmrn In;
:1
An me wnrkeu in continuouspracess.
Workers Emplnyed m we dyemg.blanching and ‘ hmgsmrjons.Wurk n
f pcrsans employed
e upcrmmns and
w.
me pumpmg o
f
‘ bulk lunsl'ero
f
m
l
(mm orlluo mag: tanks.
Any special c
l 5
u
!
warkcrsmgagod and walk on: demd be gcssznflnl cranium-mus m We. nn e
or me duuu invulvcflWork an Iummntengaged in galva ‘
and mamelmg.
cqnipmanl
WorL' o
f persons m [ha mmnesexcapl “I. gdzpnnman
Susanna: 51,
54. 57
and 51
— 3mm :45
chum. —
—same a above—
swmns 51 5151.
Sections SL 52.
54.55, 56 and 61
——ezmens above—
Sccuons 5s and 6L
5
Exempunn nan. me- pmwsians nfzecunn 5
1nppi sa In. as n rzlnlcs o
ec an I
!
nthc period mes:me numn ul'wm‘k period for mu
— same as
may: ~
— same as
«have 4
um exceed those rncmilmcd m m
Aseumn (47 ulstcnnu 64
2
.
The extmplmn mu be gmmeu umy m{1:5pr flfflUflfl ane workers.Exemphnn |o|mg|v h macm'cflnspucmrnfFm he cnnsldcrs i1 necessary an
ap y
lhe Manager
I
,
Thel mls ofwmk ‘nclns' e
nl‘nvemmcsh: nm exceed we mam nod m sub—secuanmmraec nfi-‘l
2 The exampx n
sn he gunned only inrefined o
r
ad male workers.
um um: c
l
swung wmk, cm, o
r
eaeh workershall be en clad 2
..
Farm Nos B—A
T
H
E
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
IE
S
R
U
L
E
S
‘
1
9
5
0
3
5
7
(1)
Rumba: faclurigs,
l3)
Ric: Muls
(4)
Coffee andCnsnnwnm factories
Ming) (5)
MntchurwundInd warkmghumn;m3).
64 m Nev/splines prinnng
(I).
Fanatics.
Work nrpcrsnns in rubba factories.
War); a
! pbrsuns angugad in drying.“fling nnd smring rrr
paddy.Wark o
r persons :ngngcd m rec g
,drying. lining and Hum-lg. nnpnelm mumhdled com.» nnn CzihcwnulxWork a
! persons engaged in drying n
rrpnnrs and Venus in Hum]! 117
wandwnrkmg fink/rigs.Ttlcpnming 5mm: only m us: n
fbrnnkdorvn. mmmenanzc and repairing.
Secflms 55 Ind G
I
~snme as
aban—
— name ns
abov: —
-- sam 15
WW: —
secnnns 51.
54. and 56
Exemplmn rrrnn Lite pmv' on:
arsecrion 5
:
w | apply In an
m .5 i
t
rel-m no
[hesmmcnnnn nflllt periods aha" imerval
m m
:
“(nice nfwm‘k pariad (or Mum.
4 Sam: ns
nhov: —
4 name as
lbw: «—
# sum: as
abav: —
4 2an ns
zbcve —
64mm Ind
64 (3).
A11
{ncmries
54(2) Any factory or
class at
(k)
dmfiption o
f
{flames us
my be ncnfied by
th:Sm: Government in m:OIficml G
and Unlnndrng o
f
RailwayLamas urTmcks.
mpnmnc: as may u
:
find by
the Sum Govcmmcm in rhn
a
v
Gazelle.
Sufinna 5x.
52.
54.
55.55 and 51
Saclions 51.
52 54.
55.56 and
53.
1
.
The hm": nrwurk inclusr no nverumeslm“ not
cxcnad nunne mnnuned in sub-section (4)
nfswrion 64.
r
i
Tn: exampunn shall b
:
l
‘
iled m adulxmal: wanker.
3
5
8
T
H
E
T
A
M
IL
N
A
D
U
F
A
C
T
O
R
B
K
U
L
'E
S
,
1
9
5
0
CHAPTER VII
Employment of young persons
[85. - * * * Omittedj
1[86. 2[Register of adult workers and young persons].-The factories
permitting or allowing young person workers who have completed the age of fourteen
years but have not completed the age of eighteen years and carrying token and
certificate as laid down under sections 68 and 69 of the Act shall 2[record the
particulars of such young persons in the register of adult workers young persons in
Form No. 12). The date of birth indicated in 2(column (3) of Form No. 12], shall
be supported by a birth certificate issued by the local authorities who are vested
with powers for recording and issuing birth and death certificates, namely, village
Panchayats/Panchayat Unions/Municipalities/Corporations, as the case may be.
The Manager shall make available the birth certificate of the young person
workers for verification and inspection, to the Inspector on demand at all times during
the working hours or when any work is being carried on in the factory. The Register
for young person workers shall be preserved for a period of three years, after the
last entry.]
3(86-A. Certificate of fitness. -(a) The certificate of fitness to be granted
under section 69 shall be in Form No. 5. In the event ofloss of the original certificates,
the Manager shall apply to the Certifying Surgeons for the grant of duplicates. The
Certifying Surgeon shall after verification with his records grant duplicate certificates.
CHAPTER VIII
Leave with wages
5[86-B.J Method of calculating cash equivalent 011 account of
concessional sale of foodgrains and other articles. - The cash equivalent of
Rules prescribed the advantage accruing through the concessional sale of
under sub-section foodgrains and other articles payable to workers proceeding
(3) of section 80. on leave shall be the difference between the value at the
average market rates prevailing during the month immediately preceding his leave
and the value at the concessional rates allowed of foodgrains and other articles he
is entitled to.
1 Subs. by GO. Ms. No. 24, Lab. and Emp. (M-2), dated the 12th February 1993.
2 Subs. by GO. Ms. No. 121, Lab. and Emp. (M-2), dated the 31st July, 2012.
3
4
5 Renumbered by GO. Ms. No. 644, Lab. and Emp., dated 25th March, 1982.
Ins. by GO. Ms. No. 644, Labour and Employment, dated 25th March, 1982.
R.86-B] THE TAMIL NADU FACTORIES RULES, 1950
(b) A fee of4�200/-(Rupees two hundred only)] shall be charged
for such certificates or renewal thereof or such duplicates. The fee shall be paid
by the Occupier into the local treasury and the receipt attached with the application]
Subs. by GO. Ms. No 132, Labour and Employment (M-2), 28th September, 2018.
For the purpose of the cash equivalent, monthly average
market rate of foodgrams and other articles shall be computed at
the end of every month.
87. Leave with wages register.-(!) The
Rules 87-94 Manaaer shall keep an up-to-date Register in
prescribed under Form "No 15 hereinafter called the Leave with
secllons 83 and • .
112. Wages Register :
Provided that if the Chief Inspector is of the opinion that any
muster-roll or register maintained as part of the routine of the
factory, or return made by the Manager, gives in respect of any or
all of the workers in the factory, the particulars required for the
enforcement of Chapter VIII of the Act, he may, by order in writ
ing, direct that such muster-roll or register or return shall, to the
corresponding extent, be maintained m place of and be treated as
the register or return required under this rule in respect of that
factory.
(2) The Leave with Wages Register shall be preserved for a
period of three years after the last entry in it and shall be produced
before the Inspector on demand.
88. Leave Book.-(1) The Manager shall provide each
worker who has become entitled to leave during a calendar year,
- with a book in Form No. 15 (hereinafter called the Leave Book)
not later than the 31st January of that year. The Leave Book shall
be the property of the worker, and the Manager or his agent shall
not demand it except to make entries and shall not keep it for
more than one week at a time :
Provided that if a worker to whom sub-section (3) of section 79
of the Act applies is discharged or dismissed from service before he
is provided by the manager with the Leave Book, the Manager
shall, within one week from the date of such discharge or dismis
sa], issue to such worker an abstract from the "Leavo with Wages
Register" in Form No. 15 maintained under rule 87.
(2) If a worker loses his Leave Book the Manager shall
provide him with another copy on the payment of fifteen paise, and
shall complete it from his record.
89. Medical certificate.-If any worker is absent from
work due to his illness and he wants to avail himself of the leave
with wages due to him to cover the period of his illness as far as
possible under the provisions of sub-section (7) of section 79 of
Chapter VIII as revised by the Factories (Amendment) Act, 1954,
he shall. if required by the Manager. produce a medical certificate
signed by a registered medical practitioner or by a registered or
recognised vaid or hakim stating the cause of the absence and the
period for which the worker is, in the opinion of such medical
practitioner, vaid or hakim, unable to attend to his work.
TAMIL NADU FACTORIES RULBS, 1950 [R. 89
R. 95] TAMIL NADU FACTORIES 'RULES, 1950
90. [Omitted].
91. Notice by worker.-Before or at the. end of every
calendar year. a worker who may be required to avail of I.eave in
accordance with sub-section (8) of section 79 of the Factories Act,
1948, may give notice to the Manager of his intention not to a�ail
himself of the leave with wages falling due dunng the followu�g
calendar year. The Manager shall make an entry to that effect m
the Leave with Wages Register and in the Leave Book of the
worker concerned.
92. Grant of leave with wages.-(1) Whenever leave with
wages is given to any worker, necessary entries shall be made in the
Leave with Wages Register and the Leave Book of the worker
concerned.
(2) As far as circumstances permit, members of the same
family shall be allowed leave at the same time.
(3) A worker may exchange the period of bis leave with
another worker, subject to the approval of the Manager.
93. { Payment of wages if the worker dies.- If a worker dies
before he resumes work, the balance of his pay due for the period
of leave with wages not availed of shall be paid to bis nominee
within one week of the receipt of intimation of the death of the
worker.
For this purpose each worker shall submit a nomination in
Form No. 34 duly signed by himself and attested by two witnesses.
The nomination shall remain in force until it is cancelled or revised
by another nomination.
94. Factories exempted under section 84.-(1) Where an
exemption is granted to any factory under section 84, the Manager
shall display at the main entrance of the factory a notice, giving
full details of the system established in the factory for leave with
wages and shall send a copy of it to the Inspector.
(2) No altheration shall be made in the scheme approved
by the State Government at the time of granting exemption under
section 84 without their previous sanction.
94-A. Exemption of certain factories. +The Chief Inspector
may grant exemption from all or any of the provisions of rules 87
to 93 in respectof all or any of the workers in any factory subject
to such conditions as he may impose.
Rule pres
cribed under
section 87
CHAPTER IX
Special provisions
95. Dangerous operations. - (1) The following
operations when carried on in any factory are declared to
be dangerous operations under section 87 : -
1 . Manufacture of aerated water and processes incidental thereto.·
1[2. Electroplating or oxidation of metal articles by use of an electrolyte·
containing acids, bases of salts of metals such as chromium, nickel,
cadmium, zinc, copper, silver, gold, etc.]
3. Manufacture and repair of electric accumulators.
4. Glass manufacture.
5. Grinding or glazing of metals.
6. Manufacture and treatment of lead and certain compounds of
lead.
2[7. Generation of gas from dangerous petroleum.]
8. Cleaning or smoothing of articles by ajet of sand, metal shot
or grit or other abrasive propelled by a blast of compressed air
or steam.
9. Liming and tanning of raw hides and skins and processes incidental
thereto.
10. Cellulose spraying.
1 1 . Graphite powdering and incidental processes.
12. Certain lead process carried on in printing presses and type foundries.
13. Cashewnut processing.
14. Dyeing, stenciling and painting of mats, mattings and carpets in
coir and fibre factories.
3[15. Pottery and ceramics industry.
16. Chemical works.]
4[ 17. Manufacture of dichromates.
I Subs. by GO. Ms. No. 2347, Lab. and Emp, dated the 27th October, 1988.
2 Item 7, substituted by GO. Ms. No. 3744, Industries, Labour and Co-operation
(Labour), dated the 29th July, 1960.
3 ltems 15 and 16, added by GO. Ms. No. 2501, Industries, Labour and Co-operation
(Labour), dated the 7th May, 1962.
4 Item 17, added by GO. Ms. No. 5135, Industries, Labour and Co-operation
(Labour), dated the 25th October, 1963. >
THE TAMIL NADU FACTORIES RULES, 1950 [R.95
R.95] THE TAMIL NADU FACTORIES RULES, 1950
1 [ 18. Compression of oxygen and hydrogen produced by the electrolysis
of water.
2[ 19. Manipulation of stone or any other material containmg free sihca.
20. Handling and processing of asbestos, manufacture of any article
of asbestos and any other process or manufacture or otherwise
in which asbestos is used in any form.
2 1 . Handling and manipulation of corrosive substances.]
3[22. Manufacture or mampulation ofCarcinogemc Dye intermediates.]
4[23. Process of extracting oils and fats from vegetable and animal
sources in Solvent Extraction Plants.]
5[24. Fireworks Manufactones and Match factories.]
6[25. Manufacture or manipulation of Manganese and its compounds.]
7[26. Carbon-disulphide plants.]
8[27. Manufacture, handling and use of Benzene.]
9[28. Operations involvmg High Noise Levels.
29. Manufacture or manipulation of dangerous pesticides
30 . Manufacture of Rayon by Viscose Process.
10[3 I Flammable liquefied or compressed gases and highly flammable
hquidsj.]
11[32. Operations in foundries and furnaces.]
I Item 18, added by GO. Ms No. 3461, Industries, Labour and Housing (Labour),
dated the 7th October, 1968.
2 Items 19 to 2 1 , added by GO Ms. No. 1195, L & E, dated the 27th November,
1974
3 Item 22, added by G.0. Ms. No. 1222, L & E, dated the l 0th December, 1974.
� Item 23, added by G.O. Ms No 680, L & E, dated the 20th July, 1976.
5 Item 24, added by G.O. Ms. No 41, L & E, dated the 21st January, 1976.
6 Item 25, added by G.O. Ms. No 643, L & E, dated the 24th July, 1975
7 Item 26, added by G 0. Ms No 314, L & E, dated the 17th April, 1976.
8 Item 27, added by G.0. Ms. No. 906, L & E, dated the 19th November, 1975
9 Items 28 to 3 1 , added by G.O Ms. No. 185, L & E, dated the I st March, 1988.
rn Subs by G 0. Ms. No. 1 10 , L & E, (M-2), dated the 16th September, 2008, for
" 31 . Highly flammable liquids and flammable compressed gases ". \
II Item 32, subs. by G.O Ms. No. 255, L & E (M-2), dated the 25th October, 2013.
12 Ins by G.O Ms No. 644, L & E, dated the 25th March, 1982.
12[(1-A) (a) The fee foi medical examination of workers by the Certifying
Surgeon as required by the Schedules annexed to this rule, shall be 13({200/-(Rupees
two hundred only)) for each examination of any such worker.
13Subs. by GO. Ms. No 132, Labour and Employment (M-2), 28th September, 2018.
(b) The fee charged in clause (a) shall be exclusive of an)
charges for biological; radiological or other tests which may have to be
carried out in connection with the medical examination. Such charges
shall be paid by the occupier.
( c) The fee shall be paid by the occupier into the local treasury
and the receipt attached with the application.]
(2) The provisions specified in the schedules annexed hereto shall
apply to any class or description of factories wherein dangerous opera
tions specified in each schedule are carried out.
(3) This rule shall into force in respect of any class or description
of factories, wherein the said operations are carried on, on such dates as
the State Government may by notification in the Official Gazette appoint
in this behalf.
1[(4) Notwithstanding the provisions specified in the Schedules
annexed to this rule, the Inspector may by issue of orders in writing to the
manager or occupier or both, direct them to carry out such measures, and
within such time, as may be specified in such order with a view to
2[remove] conditions dangerous to the health of the workers, or to
suspend any process, where such process constitutes, in the opinion of
the Inspector, imminent danger of poisoning or ioxicity.]
3[(5) Any register or record of medical examinations and tests
connected therewith required to be carried out under any of the
schedules annexed hereto in respect of any worker shall be kept readily
available to the Inspector and shall be preserved till the expiry of one year
after the worker ceases to be in employment of the factory.]
4[(6) 'First employment' means employment for the first time in
a hazardous process or operation so notified under Section 87, or re
employment therein after cessation of employment in such process or
operation for a period exceeding three calendar months.]
! ::���\��M�N:�ii;,3i.a1::�:,rd:�:dE;f�::;,�::��ifh July 1980.
3 Added by 0.0. Ms. No. 366, Labour, dated 23rd February, 1985.
4 Ins. by 0.0. Ms. N?. 1852, Labour and Employment, dated 31st August ·1988
TAMILNADUFACTORIESRULES, 1950 [R.95
R.95] TAMILNAOUFACTORIESRULES, 1950
SCHEDULE JI
Manufacture of aerated waters and processes incidental thereto
1. Fencing of machines. •• All machines for filling bottles or syphons
shall be so constructed, placed or fenced as to prevent as far as may be
practicable, a fragment of a burstingbottle or syphon from striking any
person employed in the factory.
2. Face-guards and gauntlets. - (1) The occupier shall pr�vide and,
maintain in good condition for the use of all persons engage9 in filling
bottles or syphons -- ·
( a) suitable face-guards to protect the face, neck /and throat,
and
(b) suitable gauntlets for both arms to protect the whole hands·
and arms:
Provided that --
(i) paragraph 2 (1) shall not apply where bottles are filled
by means of an automatic machine so constructed that no fragment' of a
bursting bottle can escape, and
(ii) where a machine is so constructed that only one arm of
the bottle at work upon it is exposed to danger, a gauntlet need not be
provided for the arm which is not exposed to danger.
(2) The occupier shall provide and maintain in good condition for
the use of all persons engaged in corking, crowning, screwing, wiring,
foiling, capsuling, sighting 1[,handling] or lab�lling bottles or syphons --
( a) suitable face-guards to protect the face, neck and throat,
and
(b) suitable gauntlets for b�h arms to protect the arm and
atleast half of the palm and the space between the thumb and forefinger.
3. Wearing of face-guards and gauntlets. •• All persons engaged in
any of the processes specified in paragraph (2) shall, while at work in such
1 Ins. by G.O. Ms. No. 1252, Labour and Employment, dated the 19th October,
1978.
TAMIL NADU FACTORIES RULES, 11950' [R.95
processes, wear the faceguards and gauntlets provided under the
provisions of the said paragraph.
1 [Schedule n
Electrolytic plating or oxidation of metal articles by use of ll11
electrolyte containing acids, bases or salts of metals such as chromium,
nickel, cadmium, zinc, copper, silver, gold, etc.
1. Definitions ••• For the purposes of this schedule, -·
(a) "electrolytic process" means the electrolytic plating or oxida
tion of metal articles by the use of an electrolyte containing acids, bases
or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver.
gold, etc.
(b) "bath" means any vessel used for an electrolytic process or for
any subsequent process ; and
( c) "employed" means employed in any process involving contact
with liquid from a bath •
.2. E_xhaust draught ••• An efficient exhaust draught shall be applied
to every vessel in which an electrolytic process is carried on. Such draught
shall be provided by mechanical means and shall operate on the vapour
or spray given off in the process as near as may be at the point of origin.
The exhaust draught appliance shall be so constructed, arranged and
maintained-as to prevent the vapour or spray entering into any room or
place in which work is carried on.
3. Prohibition relating to women and young persons .-- No woman,
adolescent or child shall be employed or permitted to work at a bath.
4. Floor ofworkrooms .-The floor of every workroom containing a
bath shall be impervious to water. The floor shall be maintained in good
and level condition and shall be washed down at least once-a day.
S. Protective devices.- (1) The occupier shall provide and maintain
in good and clean condition the following articles of protective devices
for the use of all persons employed on any process at which tltey are liable
1 Subs. by. G.O. Ms. No. 1852, Labour and Employment, dated 31st August, 1988.
R.95] TAMILNADUFACTORIES RULES, 1950
to come in contact with liquid from a bath and such devices shall be worn
by the persons concerned --
(a) waterproof aprons and bibs ; and
(b) for persons actually working at a bath, loose- fitting rubber
gloves and rubber boots or other waterproof footwear, and chemical
goggles.
(2) The occupier shall provide and maintain for the use of all
persons employed suitable accommodation for the storage and drying of
protective devices.
6. Water facilities ••• (1) There shall be provided and maintained in
good repairs for the use of all persons employed in electrolytic process
and processes incidental to it --
( a) a wash place under cover, with either --
(i) a trough with a smooth impervious surface fitted with a
waste pipe, and of sufficient length to allow at least 60 ems. for evety 5
persons employed at any one time, and having a constant supply. of water
from taps or jets above the trough intervals of not more than 60 ems ; 'or
' (ii) at least one wash basin for every five such persons :.
employed at any one time, fitted with a waste pipe and having a constant
supply of water laid on ;
(b) a sufficient supply of clean towels renewed daily, and soap
or other suitable cleaning material.
(2) In addition to the facility in sub-paragraph (1) an approved
type of emergency shower with eye fountain shall be provided and
maintained in good working order. Wherever necessary, in order to
ensure continuous water supply, storage tank of 1,500 litres capacity shall
be provided as a source of clean water for emergency use.
7. Cautionary pffatard .-A cautionary placard in the form specified
below and printed in the language of the majority of the workers
employed shall be affixed in a prominent place in the factory where it can
be easily and conveniently read by the workers.
;
TAMIL NADU FACTORIES RULES; 1950
CAUTIONARY NOTICE
(R.95
Electrolytic Plating
· 1. Chemicals handled in this plant are corrosive and poisonous.
2. Smoking, chewing tobacco, eating food or drinking, in this area
is prohibited. No food stuff or drink shall be brought in this area. ,
3. Some of these chemicals may be absorbed through the skin and
may cause poisoning.
4. A good wash shall be taken before meals.
5. Protective devices supplied shall be used while working in this
ar ea .-
6. Spillage of the chemicals on any part of the body or on the floor
shall be immediately washed away with water.
7. All workers shall report for the prescribed medical tests
tegularly to protect their own health.
8. Medical facilities and records of examinations and tests.- (1)
The occupier of every factory in which electrolytic processes are carried
on s h all - -
( a) employ a qualified medical practitioner for medical surveil
lance of the workers employed 'therein whose appointment shall be
subject to the approval of the Chief Inspector of Factories ;
(b) provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause ( a ) ; and
(c) maintain a sufficient supply of suitable barrier cream,
ointment and impermeable water proof plaster in a separate box readily
accessible to the workers and used solely for the purpose of keeping these
substances. In case cyanides are used in the bath, the box shall also
contain an emergency cyanide kit. \
(2) The medical practitioner shall examine all workers before they
. are employed in electrolytic processes. Such examination in case of
R.95] TAMILNADUFACTORIESRULFS, i95U
chrome plating shall include inspection of hands, forearms and nose and
will be carried out once at least in every fortnight.
(3) The record of the examinations referred to in sub-paragraph
(2) shall be maintained in a separate register approved by the Chief
Inspector of Factories which shall be kept readily available for inspection
by the Inspector.
9. Medical examination by the Certifying Surgeon ••• (1) Every
worker employed in the electrolytic processes shall be examined by a
certifying surgeon before his first employment. Such examination shall
- include X-!ay of the chest and -
(a) in case of chromium plating, include examination for nasal
septum perforation and test for chromium in urine ;
(b) in case of nickel plating, test for nickel in urine ; and
( c) in case of cadmium plating, test for cadmium in urine and
- 2 microlobulin in urine.
(2) No worker shall be employed in any electrolytic process lfnless
certified fit for such employment by the Certifying Surgeon.
(3) Every worker employed in the electrolytic processes shall be
re-examined by a Certifying Surgeon at least once in every year except in
case of the workers employed in cadmium, chromium and nickel plating
processes for whom this examination shall be carried out once in every
six months. Such re-examination shall, wherever the Certifying Surgeon __
considers appropriate, include tests as specified under sub-paragraph (1)
excluding the X-ray of the chest which shall not be required normally to
be carried out earlier than once in three years.
( 4) The Certifying Surgeon after examining a worker shall issue a
Certificate of Fitness in Form 27. The record of examination and re
examinations carried out shall be kept in the custody of the manager of
the factory. The record of each examinations carried out under sub
paragraphs (1) and (2), including the nature and the results of the tests
shall also be entered by the Certifying Surgeon in a health register in Form
17.
(5) The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
TAMIL NADU FACTORIES RULES, [R.95
( 6) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the electrolytic processes on
the ground that continuance therein would involve danger to the health
of the worker, he shall make a record of his findings in the said certificate
and the health register. The entry of his findings in those documents
should also include the period for which he considers that the said person
is unfit for work in the said processes. The person declared unfit in such,
circumstances shall be provided with alternate placement facility unless
he is fully incapacitated in the opinion of the Certifying Surgeon, in which
case the person affected shall be suitably rehabilitated.
(7) No person who has been found unfit to work as said in
sub-paragraph (6) shall be re-employed or permitted to work in the said
processes unless the Certifying Surgeon, after further examination again
certifies him fit for employment in those processes.]
I
SCHEDULE III
'Manufacture and repair of electric accumulators
_1. Savings.·· This Schedule shall not apply to the manufacture or ·
repair of electric accumulators or parts thereofnot containing lead or any
compound of lead ; or to the repair on the premises, of any accumulator
forming part of a stationary battery.
2. Definitions. ·- For the purposes of this schedule :
(a) "Lead process" means the melting of lead or any materials
containing lead, casting, pasting, lead burning, or any other work, includ
ing trimming, or any other abrading or cutting of pasted plates, involving
the use, movement or manipulation of, or contact with, any oxide of lead.
(b) "Manipulation of raw oxide of lead" means any lead process
involving any manipulation or movement of raw oxides of lead other than
its conveyance in a receptacle or by means of an implement from one
operation to another.
1(c) [* * *] Omitted
3. Prohibition relating to women and young persons. -· No woman
or young person shall be employed or permitted to work in any lead
1 Omitted by G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
R.95] TAMIL NADU:f'.ACTORIES RULES,
process or in any room in wliich the manipulation of raw oxide of lead or
pasting is carried on.
4. Separation of certain processes. -- Each of the following processes
shall be carried on in such a manner under such conditions as to secure
effectual separation from one another, and from any other process : --
(a) Manipulation of raw oxide of lead;
(b) Pasting ;
( c) Drying of pasted plates ;
( d) Formation with lead burning ("tacking") necessarily carried
on in connexion therewith ;
( e) Melting down of pasted plates.
'
5. Air-space. -- In every room in which a lead process is carried on, -
there shall be at-least 14.2 cubic metres of air space for each person
employed therein, and in computing this air space no height over 3.7
metres shall be taken into account.
6. Ventilation. •• Every workroom shall be provided with inlets and
outlets of adequate size as to secure and maintain efficient ventilation in
all parts of the room.
7. lDistance between workers in pasting room. -- In every pasting
room the distance between the centre of the working position of any
paster and that of the paster working nearest to him shall not be less than
1.5·metres.
8. Floor of work-rooms. -- (1) The floor of every room in which a
lead process is carried on shall be --
( a) of cement or similar material so as to be smooth and
impervious to water ;
(b) maintained in sound condition ;
(c) kept free from materials, plant, or other obstruction not
required for, or produced in, the process carried on in the room. .
[R.95
{2) In all such rooms other than grid casting shops the floor shall
be cleansed daily after being thoroughly sprayed with water at a time
when no other work is being carried on in the room.
{3) In grid casting shop the floor shall be cleansed daily.
( 4) Without prejudice to the requirements of sub-paragraphs (1),
, (2) and (3) where manipulation of raw oxide of lead or pasting is carried
on, the floor shall also be --
( a) kept constantly moist while work is being done;
(b) provided with suitable and adequate ar.rangements for
drainage;
( c) thoroughly washed daily by means of a hose pipe.
9. Work-benches.·· The work benches at which any lead process is
carried on shall --
(a) have a smooth surface and be maintained in sound condition;
(b) be kept free from all materials or plant not required for,:G. __
prod�ced in, the process carried on thereat;
- and all such work-benches other than those in grid casting shops shall -
( c) be cleaned dally either after being thoroughly damped or by
means of a suction cleaning apparatus at a time when no other work is
being carried on thereat ;
and, all such work-benches in grid casting shops shall -
( d) be cleansed daily ;
and every work-bench used for pasting shall --
( e) be covered throughout with sheet lead or other impervious
material;
(t) be provided with raised edges ;
(g) be kept constantly moist while pasting is being carried on.
TAMIL NADU FACTORIES RULES, 1950 l
R.95]
10. Exhaust draught. -- The following processes shall not be carried
on without the use of an efficient exhaust draught ;
(a) Melting of.lead or materials containing lead.
(b) Manipulation of raw oxide of lead, unless done in an enclosed
apparatus so as to prevent the escape of dust into the workroom.
(c) Pasting.
( d) Trimming, brushing, filing or any other abrading or cutting of
pasted plates giving rise to dust.
( e) Lead burning, other than
(i) "tacking" in the formation room ;
(ii) chemical burning for the making of lead linings for cell
cases necessarily carried on in such a manner, that the application of
efficient exhaust is impracticable.
Suchexhaust draught shall be effected by mechanical means and
shall operate on the dust or fume given off as nearly as may be at its point
of origin, so as to prevent itsentering the air of any room in which persons
work.
11. Fumes and gases from melting pots. -- The products of combus
tion produced in the heating of any melting pot shall not be allowed to
escape into a room in which persons work.
12. Container for dross. - A suitable receptacle with tightly fitting
cover shall be provided and used for dross as it is removed from every
melting pot. Such receptacle shall be kept covered while in the workroom,
except when dross is being deposited therein.
13. Container for lead waste. •• A suitable receptacle shall be
provided in every workroom in which old plates and waste material which
may give rise to dust shall be deposited. .,
14. Racks or shelves in drying room. -The racks or shelves provided
in any drying room shall not be more than 2.4 metres from thy floor not
more than 61 centimetres in width : provided that as regards racks or
TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 [R.95
shelves set or drawn from both sides the total width shall not exceed 1.2
metres.
Such racks or shelves shall be cleansed only after being thoroughly
damped unless an efficient suction cleaning apparatus is used for this
· purpose.
1[15. Medical facilities and records of examinations and tests. --(1)
The occupier of every factory in which manufacture and repair of electric
accumulators is carried on shall -
(a) Employ a qualified medical practitioner for medical sur
veillance of the workers employed therein, whose employment shall be
subject to the approval of the Chief Inspector of Factories ; and
(b) Provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The record of medical examination and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector of Factories, which
shall be kept readily available for inspection by the Inspector.
15-A. Medical examination by Certifying Surgeon . •• (1) Every
worker employed in lead processes shall be examined by a Certifying
Surgeon within 15 days of his first employment. Such examination shall
",iclude tests for lead in urine and blood. ALA in urine, haemoglobin
content stippling of cells and steadiness test. No worker shall be allowed
to work after 15 days of his first employment in the factory unless certified
fit for such employment by the Certifying Surgeon.
(2) Every worker �pioyed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every three calendar
months. Such re-examination shall, wherever the Certifying Surgeon
considers appropriate, include tests specified in sub-paragraph (1).
(3) The Certifying Surgeon after examining a worker, shall issue
a Certificate of Fitness in Form 27. The record of examination and re
examinations carded out shall be entered in the certificate and the
1subs. vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
R.95] TAMILNADUFACTORIESRULES, 1950
c�rtificate shall be kept in the custody of the Manager of the factory. The
record of each examination carried out under sub- paragraphs (1) and
(2), including the nature and the results of the tests, shall also be entered
by the Certifying Surgeon in a Health Register in Form 17.
( 4) The Certificate of Fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker he shall make a record of his findings in the said certificate and
the health register. The entry of his findings in those documents should
also include the period for which he considers that the said person is unfit
for work in the said processes. The person so suspended from the process
shall be provided with alternate placement facilities unless he is fully
, incapacitated in the opinion of the Certifying Surgeon, in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in
sub-paragraph (5) above shall be re- employed or permitted to work in
the said processes unless the Certifying Surgeon, after further examina
tion, again certifies him fit for employment in those processes.]
16. Protective clothing. •• Protective clothing shall be provided and
maintained in good repair for all persons employed in --
( a) manipulation of raw oxide of lead ;
(b) pasting ;
( c) the formation room ;
and such clothing shall be worn by the persons concerned. The protective
clothing shall consist of a waterproof apron and waterproof footwear ;
and, also as regards persons employed in the manipulation of raw oxide
of lead or in pasting, head coverings. The head coverings shall be washed
daily.
17. Mess-room. •• There shall be provided and maintained for the
use of all persons employed in a lead process and remaining on the
premises during the meal intervals, a suitable mess-room which shall be
a 7 g TAMIL NADU Factotuas RULES, ‘1950
,
.
[ng5
furnished with (a) sufficient tables and benches, and (b) adequate means
for warming food.
The mess-room shall he placed under the charge of a responsible
person, and shall be kept clean
18. Cluck-room. — Them shall be provided and maintained for the
use of all persons employed in a lead process
»-
‘
(a) A clock-room for clothing put off during working hours with
adequate arrangements for drying the clothing ifwet. Such aecommoda~
Lion shall be separate from any mess-room.
(b) Separate and suitable arrangements for the storage of protec-
tive clothing provided under paragraph 16‘
19. Washing facilities. — There shall be provided and maintained in
a cleanly state and in good repair [or the use of all persons employed in
a‘ lead process
——
(a) A wash place under cover, with either ->
<(i) a trough with a smooth impervious surface fitted with a‘
waste pipe without plug, and of sufficient length to allow of at least 61
centimetres for every five such persons employed at any one time, and
_ having a constant supply of water from taps or jets above the trough at
intervals of not more than 61 centimetres; or
(ii) at least one washbasin for every five such persons employed
at any one time, fitted with a waste pipe and plug and having a constant
supply of water laid on ;
(iii) a sufficient supply of clean towels made of suitable
materials renewed daily,Which supply, in the ease of paslers and persons
employed in the manipulation of raw oxide of lead, shall include a
separate marked towel for each such worker ; and
(iv) a sufficient supply of soap or other suitable cleansing
material and of nail brushes.
(1:) There shall in additionbe provided means ofwashing in élose
proximity to the rooms in which manipulation of raw oxide of lead or
R.95)
pasting is carried on if required by notice in writing from the Chief
Inspector.
20. Time to be allowed for washing. •• Before each meal and before
the end of the day's work, at least ten minutes, in addition to the regular
meal times, shall be allowed for washing to each person who has been
employed in the manipulation of raw oxide of lead or in pasting :
Provided that if there be one basin or 61 centimetres of trough for
each such person this rule shall not apply .
.U. Facilities for bathing. •• Sufficient bath accommodation to the
satisfaction of the Chief Inspector shall be provided for all persons
engaged in the manipulation of raw oxide of lead or in pasting, and a
sufficient supply of soap and clean towels.
22. Food, drinks, etc., prohibited in workrooms. - - No food, drink,
pan and supari or tobacco shall be consumed or brought by any worker
into any workroom in which any lead process is carried on.
SCHEDULE IV
Glass manufacture
1. Exemptions ••• If the Chief Inspector is satisfied in respect of any
factory or any class of process that, owing to the special methods of work
or the special conditions in a factory or otherwise, any of the requirements
of this schedule can be suspended or relaxed, without danger to the
persons employed therein, or that the application of this schedule or any
part thereof is for any reason impracticable, he may by certificate in
writing authorise such suspension or relaxation as may be indicated in the
certificate for such period and on such conditions as he may think fit.
2. Definitions.·· For the purpose of this schedule --
(a) "Efficient exhaust draught" means localised ventilation ef
fected by mechanical means, for the removal of gas, vapour, dust or fumes
so as to prevent them ( as far as practicable under the atmospheric
conditions usually prevailing) from escaping into the air of any place in
which work is carried on. No draught shall be deemed efficient which fails
to remove smoke generated at the point where such gas, vapour, fume,
or dust originate.
TAMIL NADU FACTORIES RULES,• 1950
TAMILNADUFACTORIESRULES, 1950 [R.95
(b) "Lead compound" means any compound of lead other than
galena which, when treated in the manner described below, yields to an
aqueous solution of hydrochloric acid a quantity of soluble lead com
pound exceeding when calculated as lead monoxide, 5 per cent. of the
dry weight of the portion taken for analysis.
The method of treatment shall be as follows : --
A weighed quantity of the material which has been dried at lOOoC
and thoroughly mixed shall be continuously shaken for one hour, at the
common temperature with 1,000 times its weight of an aqueous solution
of hydrochloric acid containing 0.25 per cent. by weight of hydrogen
chloride. This solution shall thereafter be allowed to stand for one hour
and then filtered. The lead salt contained in the clear filtrate shall then
be precipitated as lead sulphide and weighed as lead sulphate.
1(c) [* * *] Omitted
3. Exhaust draught. •• The following processes shall not be carried
-oil except under an efficient exhaust draught or under such other condi
tions as may be approved by the Chief Inspector : --
(a) The mixing of raw materials to form a "batch".
(b) The dry grinding, glazing and polishing of glass or any article
of glass.
(c) All processes in which hydrofluoric acid fumes or ammonical
vapours are given off.
( d) All processes in the making of furnace moulds or "pots"
including the grinding or crushing of used "pots"
( e) All processes involving the use of a dry lead compound.
4. Prohibition relating to women and young persons. •• No woman
or young person shall be employed or permitted to work in any of the
operations specified in paragraph 3 or at any place where such operations
are carried on. ·
S. Floors and work-benches. •• The floor and work- benches of every
room in which a dry compound of lead is manipulated or in which any
1
Omitted vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th
October, 1988.
R.95] TAMILNADU FACTORIES RULES, 1950
process is carried on giving off silica dust shall be kept moist and shall
comply with the following requirements : --
The floor shall be --
(a) of cement or similar material so as to be smooth and imper
vious to water ;
(b) maintained in sound conditions ; and
(c) cleansed daily after being thoroughly sprayed with water at a
time when no other work is being carried on in the room.
The work-benches shall --
(a) have a smooth surface and be maintained in sound condition,
and
(b) be cleansed daily either after being thoroughly damped or by
means of a suction cleaning apparatus at a time when no other work is
being carried on thereat.
6. Use of Hydrofluoric Acid. •• The following provisions shall apply
to rooms in which glass is treated with hydrofluoric acid : --
(a) There shall be inlets and outlets of adequate size so as to
secure and maintain efficient ventilation in all parts of the room ;
(b) the floor shall be covered with guttaparacha and be tight and
shall slope gently down to a covered drain ;
(c) the work places shall be so enclosed in projecting hoods that
openings required for bringing in the objects to be treated shall be as
small as practicable ; and
(d) the efficient exhaust draught shallbe so contrived that the
gases are exhausted downwards. ·
7. Storage and transport of Hydrofluoric acid. -- Hydrofluoric acid
shall not be stored or transported except in cylinders or receptacles made
of lead or rubber.
8. Suitable facilities shall be readily available for sterilizing the
blow-pipes. used by the glass blowers and such blow-pipes shall be
sterilized at the beginning of the operations of blowing, each day.
TAMIL NADU FACTORIES RULES, 1950 [R.95
i
' 9. Food, drinks, etc., prohibited in workrooms. -- No food, drink,
pan and supari or tobacco shall be brought into or consumed by any
worker in any room or work· place wherein any process specified in
paragraph 3 is carried on.
10. Protective clothing. -- The occupier shall provide, maintain in
good repair and keep in a clean condition for the use of all persons
employed in the processes specified in paragraph 3 suitable protective
clothing, footwear and goggles according to the nature of the work and
such clothing, footwear, etc., shall be worn by the persons concerned.
11. Washing facilities. -- There shall be provided and maintained in
a cleanly state and in good repair for the use of all persons employed in
the processes specified in paragraph 3 --
(a) a wash place with either --
(i) a trough with a smooth impervious surface fitted with a
waste pipe, without plug and of sufficient length to allow of at least 61
centimetres for every five such persons employed at any one time, and
having a constant supply of water from taps or jets above the trough at
intervals of not more than 61 centimetres ; or
(ii) at least one wash basin for every five such persons employed
at any one time, fitted with a waste pipe and plug and having an adequate
supply of water laid on or always readily available ;
and
a sufficient supply of clean towels made of suitable materials renewed
daily with a sufficient supply of soap or other suitable cleansing material
and of nail brushes ;
and
(b) a sufficient number of stand pipes with taps - - the number
and location of such stand pipes shall be to the satisfaction of the Chief
Inspector.
1[12. Medical facilities and record of examinations and tests. -- (1)
The Occupier of every factory in which glass manufacturing processes are
carried out, shall -
1 Subs. vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
R.95] TAMIL NADU FACTORIES RULES, 1950
(a) employ a qualified medical practitioner for medical surveil
lance of the workers employed therein whose appointment shall be
subject to the approval of the Chief Inspector of Factories ; and ·
(b) Provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The records of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector of Factories, which
shall be kept readily available for inspection by the Inspector.
12-A. Medical Examination by Certifying Surgeon . •• (1) Every
worker employed in processes specified in paragraph 12 shall be ex
amined by a Certifying Surgeon within 15 days of his first employment.
·· Such examination shall include pulmonary function tests and in suspected
cases chest X-ray as well as tests for lead and (sic.) urine. No worker shall
be allowed to work after 15 days of his first employment in the factory
unless certified fit for such employment by the Certifying Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every twelve calendar
months. Such re-examination shall, wherever the Certifying Surgeon
considers appropriate, include tests as specified in sub-paragraph(l).
(3) The Certifying Surgeon after examining a worker shall issue a
certificate of fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and. the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub- paragraphs (1)
and (2), including the nature and the results of the tests, shall also be
entered by the Certifying Surgeon in a Health Register in Form 17.
( 4) The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of
worker, he shall make a record of his findings in the said certificate and
the health register. The entry of his findings inthose documents should
also include the period for which he considers that the said person is unfit
TAMIL NADU FACTORIES RULES, 1950 [R.95
for work in the said processes. The person so suspended from the process,
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as' said in
sub-paragraph (5) shall be re-employed or permitted to work in the said
processes unless the Certifying Surgeon, after further examinations, again
certifies him fit for employment in those processes.]
SCHEDULEV
Grinding or glazing of metals and processes incidental thereto
1. Definitions. -- For the purposes of this schedule --
( a) "Grindstone" means a grindstone composed of natural or
manufactured sandstone but does not include a metal wheel or cylinder
. into which blocks of natural or manufactured sandstone are fitted.
(b) "Abrasive wheel" means a wheel manufactured of bonded
emery or similar abrasive.
(c) "Grinding" means the abrasion, by aid of mechanical power
of metal, by means of a grindstone or abrasive wheel.
( d) "Glazing" means the abrading, polishing or finishing by aid of
mechanical power of metal, by means of any wheel, buff mop or 'similar
appliance to which any abrading or polishing substance is attached or -
applied.
( e) "Racing" means the turning up, cutting or dressing of a
revolving grindstone before it is brought into use for the first time.
(t) "Hacking" means the chipping of the surface of a grindstone
by a hack or similar tool.
(g) "Rodding" means the dressing of the surface of a revolving
grindstone by the application of rod, bar or strip of metal to such surface.
2. Exemptions. -- (1) Nothing in this schedule shall apply to any
factory in which only repairs are carried on except any part thereof in
which one or more persons are wholly or mainly employed in the grinding
or glazing of metals.
R.95]
(2) Nothing in this schedule except paragraph 4 shall apply to any
grinding or glazing of metals carried on intermittently and at which no
person is employed for more than 12 hours in any week.
(3) The Chief Inspector may by certificate in writing, subject to
such condition as he may specify therein, relax or suspend any of the
provisions of this schedule in respect of any factory if owing to the special
methods of work or otherwise such relaxation or suspension is practicable
without danger to the health or safety of the persons employed.
3. Equipment for removal of dust. •• No racing, dry grinding or
glazing shall be performed without --
( a) a hood or other appliance so s.9nstructed, arranged, placed,
and maintained as substantially to interceprthe dust thrown off ;
(b) a duct of adequate size, air-tight and so arranged as to be
capable of carrying away the dust, which dust shall be kept free from
obstruction and shall be provided with proper means of access-for
inspection and cleaning, and where practicable, with a connection at the
end remote from the fan to enable the Inspector to attach thereto any
instrument necessary for ascertaining the pressure of air in the said
duct; and -
( c) a fan or other efficient means of producing a draught sufficient
to extract the dust :
Provided that the Chief Inspector may accept any otlier appliance
that is, in his opinion, as effectual for the interception, removal and
disposal of dust thrown off as a hood, duct and fan would be.
4. Restriction on employment on grinding operations.·· Not more
than one person snail at any time perform the actual process of grinding,
or glazing upon a grindstone, abrasive wheel or glazing appliance :
Provided that this paragraph shall not prohibit the employment of
persons to assist in the manipulation of heavy or bulky articles at any such
grindstone, abrasive wheel or glazing appliance.
S. Glazing. •• Glazing or other processes, except processes incidental
to wet grinding upon a grindstone shall not be carried on in any room in
which wet grinding upon a grindstone is done,
TAMIL NADU FACTORIES RULES, 1950 •
TAMIL NADU FACTORIES RULES, 1950 (R.95
6. Hacking and rodding. - Hacking or rodding shall not be done
unless during the process either (a) an adequate supply of water is laid
on at the upper surface of the grindstone or (b) adequate appliances for
the interception of dust are provided in accordance with the require
ments of paragraph 3.
7. Examination of dust equipment. -- (a) All equipment for the
extraction or suppression of dust shall at least once in every six months
be examined and tested by a competent person, and any defect disclosed
by such examination and test shall be rectified as soon as practicable.
(b) A rer,ster containing particulars of such examination and test
shall be kept in [Form No. 37]
2(7-A. Medical facilities and record of examinations and tests . -
(1) The occupier of every factory in which grinding or glazing of metals
are carried out, shall -
(a) employ a qualified medical practitioner for medical surve
lance of the workers employed therein whose appointment shall b
subject to the approval of the Chief Inspector of Factories ; and
(b) provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The record of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector of Factories, which
shall be kept readily available for inspection by the Inspector.
7-B. Medical examination by Certifying Surgeon. -- (1) Every
worker employed in grinding or glazing of metal and processes incidental
thereto shall be examined by a Certifying Surgeon within 15 days of his
first employment. Such examination shall include pulmonary function
tests and in suspected cases chest X-rays. No worker shall be allowed to
work after 15 days, of his first employment in the factory unless certified
fit for such employment by the Certifying Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every 12 calendar months.
1 Subs. by G.O. Ms. No. 365, Labour and Employment, dated the 10th May, 1977. ,
2 Ins. vide G.O. Ms. No.2223, Labour and Employment, dated the 6th October,
1988.
Such re· examination shall wherever the Certifying Surgeon considers
appropriate, include tests as specified in sub-paragraph (1).
(3) The Certifying Surgeon after examining a worker, shall issue
a Certificate of Fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub· paragraphs ( 1)
and (2) including the nature and the results of the tests, shall also be
entered by the Certifying Surgeon in a Health Register in Form 17.
( 4) The Certificate of Fitness and the Health Register shall be
kept readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker he shall make a record of his findings in the said Certificate and
the Health Register. The entry of his findings in those documents should
also include the period for which he considers that the said person is unfit
for work in the said processes. The person so suspended from the process
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in
sub-paragraph (5) shall be re-employed or permitted to work in the said
processes unless the Certifying Surgeon, after further examination, again
certifies him fit for employment in those processes.]
ScHEDULEVI
Manufacture and treatment of lead and certain compounds of lead
1. Exemptions. -- Where the Chief Inspector is satisfied that all or
any of the provisions of this schedule are not necessary for the protection .
of the persons employed he may by certificate in writing exempt any
factory from all or any of such provisions, subject to such conditions as
he may specify therein.
2. Definitions. •• For the purposes of this schedule •·
R.95] TAMIL NADU FACTORIES RULES, 1950
[R.95
(a) "Lead compound" means l!DY compound of lead other than
galena which, when treated in the manner described below, yields to an
aqueous solution of hydrochloric acid, a quantity of soluble lead com
pound exceeding, when calculated as lead monoxide, five per cent. of the
dry weight of the portion taken for analysis. In the case of paints and
similar products and other mixtures containing oil or fat the "dry weight"
means the dry weight of the material remaining after the substance has
been thoroughly mixed and treated with suitable solvents to remove oil,
fats, varnish or other media.
The method of treatment shall be as follows : --
A weighed quantity of the material which has been dried at 100°C
and thoroughly mixed shall be continuously shaken for one hour, at the
common temperature with 1,000 times its weight of an aqueous solution
of hydrochloric acid containing 0.25 per cent. by weight of hydrogen
chloride. This solution shall thereafter be allowed to stand for one hour
and then filtered. The lead salt contained in the clear filterate shall then
be precipitated as lead sulphide and weighed as lead sulphate.
(b) "Efficient exhaust draught" means localized ventilation ef
fected by heat or mechanical means, for the removal of gas, vapour, dust
or fumes so as to prevent them (as practicable under the atmospheric
conditions usually prevailing) from escaping into the air of any place in
which work is carried on. No draught shall be deemed efficient which fails
to remove smoke generated at the point where such gas, vapour, fumes
or dust originate.
3. Application. •• This schedule shall apply to all factories or parts
of factories in which any of the following operations are carried on : --
( a) Work at a furnace where the reduction or treatment of zinc or
lead ores is carried on.
(b) The manipulation, treatment or reduction of ashes containing
lead, the desilverising of lead or the melting of scrap lead or zinc.
{ c) The manufacture of solder or alloys containing more than ten
per cent. of lead.
. ( d) The manufacture of any oxide, carbonate, sulphate, chromate,
acetate, nitrate, or silicate of lead.
( e) Handling or mixing of lead tetra-ethyl.
TAMIL NADU FACTORIES RULES, 1950
R.95)
(f) Any other operation involving the use of a lead compound.
(g) The cleaning of workroom where any of the operations
aforesaid are carried on.
4. Prohibition relating to women and young persons. - No woman
or young persons shall be employed or permitted to work in any of the
operations specified in paragraph 3.
S. Requirements to be observed. -- No person shall be employed or
permitted to work in any process involving the use of lead compounds if
the process is such that dust or fume from a lead compound is produced
therein, or the persons employed therein are liable to be splashed with
any lead compound in the course of their employment unless the
provisions of paragraphs 6 to 14 are complied with.
6. Exhaust draught. -- Where dust, fume, gas or vapour is produced
in the process, provision shall be made for removing them by means of
any efficient exhaust draught so contrived as to operate on the dust, fume,
gas or vapour as closely as possible to the point of origin.
1 [7. Medical facilities and records of examinations and tests • -- ( 1)
The occupier of every factory to which the schedule applies shall --
( a) employ a qualified medical practitioner for medical surveil
lance of the workers employed therein whose appointment shall be
subject to the approval of the Chief Inspector of Factories ; and
(b) Provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The record of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector "of Factories, which
sha:11 be kept readily available for inspection by the Inspector.]
2 [8. Medical Examination by Certifying Surgeon • - - (1) Every
worker employed in the processes ref erred to in paragraph 1 shall be
1 Subs. vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
1988
? Subs. vide G.O. Ms. No. 2223., Labour and Employment, dated the 6th October,
TAMIL NADU FACTORIFS RULFS, 1950
A.CTORIES RULES, 1950 [R.95
examined by a Certifying Surgeon within 15 days of his first employment.
Such examination shall include tests for lead in blood and urine, ALA in
urine; haemoglobin content, stippling of cells and steadiness tests. No
worker shall be allowed to work after 15 days of his first employment in
the factory unless certified fit for such employment by the Certifying
Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every three calendar
months. Such re-examination shall, wherever the Certifying Surgeon
considers appropriate, include tests specified in sub-paragraph (1).
(3) The Certifying Surgeon after examining a worker, shall issue
a certificate of fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub- paragraphs (1)
and (2), including the nature and the results of the tests, shall also be
entered by the Certifying Surgeon in a Health Register in Form 17.
( 4) The certificate of fitness and the health register shall be kept
readily available for. inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker, he shall make a record of his findings in the said certificate and
the health register. The entry of his findings in those documents should
also include the period for which he considers that the said person is unfit
for work in the said processes. The person so suspended from the process
"shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon, in which case the
-person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in
sub-paragraph (5) above shall be re- employed or permitted to work in
the said process unless the Certifying Surgeon, after further examination,
again certifies him fit for employment in those processes.]
9. Food, drinks, etc., prohibited in workrooms.·- No food, drink,
pan and supari or tobacco shall be brought into or consu�ed by any
TAMIL NADU F
R. 95] '
worker in any workroom in which the process is carried on and no person
shall remain in any such room during intervals for meals or rest.
10. Protective clothing. -- Suitable protective overalls and head
coverings shall be provided, maintained and kept clean by the factory
occupier and such overalls and head coverings shall be worn by the
persons employed.
11. Cleanliness of workrooms, tools, etc. --The rooms in which the
persons are employed and all tools and apparatus used by them shall be
kept in a clean state.
12. Washing facilities. -- ( 1) The occupier shall provide and maintain
for the use of all persons employed, suitable washing facilities consisting
of--
(a) a trough with a smooth impervious surface fitted with a
waste pipe without plug and of sufficient length to allow at least 61
centimetres for every ten persons employed at any one time, and having
a constant supply of clean water from taps or jets above the trough at
intervals of not more than 61 centimetres ; or
(b) atleast one wash-basin for every ten persons employed at
any one time, fitted with a waste pipe and plug and having a constant
supply of clean water, together with, in either case, a sufficient supply of
nail brushes, soap or other suitable cleansing material and clean towels.
(2) The facilities so provided shall be placed under the charge of
a responsible person and shall be kept clean.
13. Mess-room or Canteen. -- The occupier shall provide and main
tain for the use of the persons employed suitable and adequate arrange
ments for taking their meals. The arrangement shall consist of the use of
a room separate from any workroom which shall be furnished with
sufficient tables and benches and unless a canteen serving hot meals is
provided, adequate means for warming food. The room shall be ade
quately ventilated by the circulation of fresh air shall be placed under the
charge of a responsible person �nd shall be kept clean.
14. Cloak-room. -- The occupier shall provide and maintain for the
use of persons employed, suitable accommodation for clothing not worn
during working hours, and for the drying of wet clothing.
TAMIL.NADU FACTORIES RULES, 1950
·. TAMIL NADU FACTORIES RULES, 1950
SCHEDULE VII
[R.95
Generation of gas from dangerous petroleum
1. Prohibition relating to women and young persons. •• No woman
or young person shall be employed or permitted to work in or shall be
allowed to enter any building in which the generation of gas from
dangerous petroleum is carried on.
2. Flame traps. •• The plant for generation of gas from dangerous
petroleum and associated piping and fittings shall be fitted with atleast
two efficient flame traps so designed and maintained as to prevent a flash
back from any burner to the plant. One of these traps shall be fitted as
close to the plant as possible. The plant and all pipes and valves shall be
installed and maintained free from leaks.
3. Generating building or room. - All plants for generation of gas
from dangerous petroleum erected after the coming into force of the
provisions specified in this schedule, shall be erected outside the factory
building proper in a separate well ventilated building (hereinafter
referred to as the "generating building"). In the case of such plant erected
before the coming into force of the provisions specified in this schedule
there shall be no direct communication between the room where such·
plants are erected (hereinafter referred to as the "generating room"), and
the remainder of the factory building. So far as practicable, all such
generating rooms shall be constructed of fire-resisting materials.
4. Fire Extinguishers. •• An efficient means of extinguishing petrol
fires shall be maintained in an easily accessible position near the plant for
generation of gas from dangerous petroleum.
5. Plant to be approved by the Chief Inspector. •• Gas from
dangerous petroleum shall not be manufactured except in a plant for
generating gas from dangerous petroleum, the design and construction
of which has been approved by the Chief Inspector.
6. Escape -,r dangerous petroleum. -- Effective steps shall be taken
to prevent dangerous petroleum from escaping into any drain or sewer.
, 7. Prohibition relating to smoking, etc. -· No person shall smoke or
carry matches, fire or naked light or other means of producing a naked
light or spark in the generating room or generating building or in the
R.95] TAMILNADU FACTORIES RULES, 1950
vicinity thereof and a warning notice in the language understood by the
majority of the workers shall be pasted in the factory prohibiting smoking
and the carrying of matches, fire or naked light or other means of
producing a naked light or spark into such room or building.
8. Access to dangerous petroleum or centatner,» No unauthorised
person shall have access to any dangerous petroleum or to vessel contain
ing or having actually contained ( dangerous) petroleum.
9. Electric fittings. -- All electric fittings shall be of flame-proof
construction and all electric conductors shall either be enclosed in inetal
conduits or be lead sheathed.
10. Construction of doors. •• All doors in generating room or
generating building shall be constructed to open outwards or to slide and
no door shall be locked or obstructed or fastened in such a manner that
it cannot be easily and immediately opened from the inside while gas is
being generated and any person is working in the generating room or
generating building.
11. IRepair of containers. -· No vessel that has contained petroleum
shall be repaired in a generating room or generating building and no
repairs to any such vessel shall be undertaken unless live-steam has been
blown into the vessel and until the interior is thoroughly steamed out or
other equally effective steps have been taken to ensure that it has been
rendered free from dangerous petroleum or inflammable vapour.
1
[SCHEDULE VIII
Cleaning, smoothing, roughening, etc; of articles by a jet
of sand, metal shot or grit or other abrasive propelled by a
blast of compressed air or steam.
1. Definitions. -· For the purposes of this schedule --
"Blasting" means cleaning, smoothing, roughening or removing
of any part of the surface of any article by the use as an abrasive of a jet
of sand, metal shot, or grit or other material, propelled by a blast, ol
compressed air or steam.
"Blast enclosures" means a chamber, barrel cabinet or any othei
enclosure designed for the performance of blasting therein.
1 Subs. byG.O. Ms. No.1195, Labour and Employment, dated the 27thNovembe1
1974.
[R.95
"Blasting chamber" means a blasting enclosure in whicli any
· person may enter at any time in connection with any work or otherw.ise.
"Cleaning of castings", where done as an incidental or sup
plemental process in connection with the making of metal castings,
means, the freeing of the casting from adherent sand or other substance
and includes the removal of dross and the general smoothing of a casting,
but does not include the free treatment.
2. Prohibition of sand blasting. •• Sand or any other substance
containing free silica shall not be introduced as an abrasive into any
blasting apparatus and shall not be used for blasting :
Provided that this clause shall come into force two years after the
coming into operation of this Schedule.
3. Precautions in connection with blasting operations. -- ( 1) Blasting
to be done in blasting enclosure. - Blasting shall not be done except in a
blasting enclosure and no work other than blasting and any work imme
diately incidental thereto and cleaning and. repairing of the enclosure
including the plants and appliances situated therein, shall be performed
in a blasting enclosure. Every door, aperture and joint of blasting
enclosure, shall be kept closed and air- tight, while blasting is being done
therein.
(2) Maintenance of blasting enclosure. -- Blasting enclosure shall
always be maintained in good condition and effective measures shall be
taken to prevent dust escaping from such enclosures and from any
apparatus connected therewith, into the air of any room.
(3) Provision of separating apparatus. -- There shall be provided
and maintained for and in connection with every blasting enclosure,
efficient apparatus for separating, so far as practicable, abrasive which
has been used for blasting and which is to be used again as an abrasive,
from dust or particles or other materials arising from blasting ; and no
such abrasive shall be introduced into any blasting apparatus and used
for blasting until it has been so separated :
Provided that this clause shall not apply, except in the case of blasting
chambers, to blasting enclosures constructed or installed before the
coming into force of this Schedule, if the Chieflnspector is of the opinion
that it is not reasonably practicable to provide such separating apparatus.
---TAMILNADU FACTqRIESRULES, 1950
TAMIL NADU FACTORIES RULES, 1950
( 4) Provision of ventilating plant. -- There shall be provided and
maintained in connection with every blasting enclosure efficient ventilat
ing plant to extract, by exhaust draught effected by mechanical means,
dust produced in the enclosure. The dust extracted and removed shall be
disposed of by such method and in such a manner that it shall not escape
into the air of any room ; and every other filtering or settling device
situated in a room in which persons are employed, other than persons
attending to such bag or other filtering or settling device, shall be com
pletely separated from the general air of that room in an enclosure
ventilated to the open air.
( 5) Operation of ventilating plant. -- The ventilating plant provided
for the purpose of sub- clause ( 4) shall be kept in continuous operation
wherever the blasting enclosure is in use whether or not blasting is actually
taking place therein, and in the case of a blasting chamber, it shall be in
operation even when any person is inside the chamber for the purpose of
cleaning.
4. Inspection and examination. -- (1) Every blasting enclosure shall
be specially inspected by a competent person atleast once in every week
in which it is used for blasting. Every blasting enclosure, the apparatus
connected therewith and the ventilating plant shall be thoroughly ex
amined and in the case of ventilating plant.tested by a competent person
atleast once in every month.
(2) Particulars of the result of every such inspection, examination
and test shall forthwith be entered in a register, which shall be kept in a
form approved by the chieflnspector and shall be available for inspection
by any workman employed in, or in connection with, blasting in the
factory. Any defect found on any such inspection, examination or test
shall be immediately reported by the person carrying out the inspection,
examination or test to the occupier, Manager or other appropriate person
and without prejudice to the foregoing requirements of this Schedule,
shall be removed without avoidable delay.
5. Provision of protective helmets, gauntlets and overalls. -· (1)
There shall be provided and maintained for the use of all persons who
are employed in a blasting chamber, whether in blasting or in any work
connected therewith or in cleaning such a chamber, protective helmets
of a type approved by a certificate of the Chief Inspector ; and every such
person shall wear the helmet provided for this use whilst he is in the
chamber and shall not remove it until he is outside the chamber.
R.95]
TAMIL NADU FACTORIES RULES, 1950 (R.95
(2) Each protective helmet shall carry a distinguishing mark
indicating the person by whom it is intended to be used and no person
shall be allowed or required to wear a helmet not carrying his mark or a
helmet which has been worn by another person and has not since be
thoroughly disinfected.
(3) Each protective helmet when in use shall be supplied wi�h
clean and not unreasonably cold air at a rate of not less than 0.17 cubic
metre per minute.
( 4) Suitable gauntlets and overalls shall be provided for the use
of all persons while performing blasting or assisting at blasting and every
such person shall, while so engaged, wear the gauntlet and overall
provided.
1[6. Precautions in connection with cleaning and other work.·· (1)
Where any person is engaged upon cleaning of any blasting apparatus or
blasting enclosure or of any apparatus or ventilating plant connected
therewith or the surroundings thereof or upon any other work in connec
tion with any blasting apparatus or blasting enclosure or with any ap
paratus or ventilating plant connected therewith so that he is exposed to
the risk of inhaling dust which has arisen from blasting, all practicabfe ·
me_)!sures shall be taken to prevent such inhalation.
(2) In connection with any cleaning operation referred to in clause
5 and the removal of dust from filtering or settling devices all practicable
measures shall be taken to dispose of the dust in such manner that it does
not enter the air of any room. Vacuum cleaners shall be provided and
used wherever practicable for such cleaning operations.]
7. Storage accommodation for protective wear. •• Adequate and
suitable storage accommodation for the helmets, gauntlets and overalls
required to be provided by clause 5 shall be provided outside, and
conveniently near to, every blasting enclosure and such accommodation
shall be kept clean. Helmets, gauntlets and overalls when not in actual
use shall be kept in this accommodation.
8. Maintenance and cleaning of protective wear. •• All helmets,
gauntlets, overalls, and other protective devices or clothings provided and
worn for the purpose of this Schedule, shall be kept in good condition
1
Subs. by G.O. Ms. No. 579, Labour and Employment, dated the 24th June, 1976.
R.95]
and so far as is reasonably practicable shall be cleaned on every week day
in which they are used. Where dust arising from the cleaning of such
protective clothing or devices is likely to be inhaled, all practicable
measures shall be taken to prevent such inhalation. Vacuum cleaners
shall, wherever practicable, be used for removing dust from such clothing
and compressed air shall not be used for removing dust from any clothing.
9. Maintenance ofvacuum cleaning plant. •• Vacuum cleaning plant
used for the purpose of this Schedule shall be properly maintained.
1[9-A. Medical facilities and records of examinations and tests • ••
(1) The occupier of every factory to which the schedule applies, shall -
(a) employ a qualified medical practitioner for medical surveil
lance of the workers employed therein whose employment shall be
subject to the approval of the Chief Inspector of Factories ; and
(b) Provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The record of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector of Factories, which
shall be kept readily available for inspection by the Inspector.
9-B. Medical Examination by Certifying Surgeon • - - (1) Every
worker employed in any of the processes to which this Schedule applies
shall be examined by a Certifying Surgeon within 15 days of his first
employment. Such examination shall include pulmonary function test and
chest X-ray. No worker shall be allowed to work after 15 days of his first
employment in the factory unless certified fit for such employment by the
Certifying Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every 12 calendar months
and such re-examination shall,' wherever the Certifying Surgeon considers
appropriate, include pulmonary function test and chest X-ray once in
every three years.
1
Ins. vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
TAMIL NADU FACTORIES k.ULES, 1950
TAMIL NADU FACTORIES RULES, 1950 [R.95
(3) The Certifying Surgeon after examining a worker, shall issue
a certificate of fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub- paragraphs (1)
and (2), including the nature and the results of the tests, shall also be
entered by the Certifying Surgeon in the Health Register in Form 17.
( 4) The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker, he shall make a record of his findings in the said certificate and
the health register. The entry of his findings in those documents should
also include the period for which he considers that the said person is unfit
for work in the said processes, The person so suspended from the process,
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon, in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work in the processes
as said in sub-paragraph (5) above shall be re-employed or permitted to
work unless the Certifying Surgeon, after further examination, again
certifies him fit for employment in those processes.]
10. Restriction in employment of young persons and prohibition of
employment of women. -- No woman or person under 18 years of age shall
be employed or permitted to work at blasting or assist at blasting or in
any blasting chamber or in the cleaning of any blasting apparatus or any
blasting enclosure or any apparatus or ventilating plant connected there
with or be employed on maintenance or repair work at such apparatus,
enclosure or plant.
11. Power to exempt or relax.» (1) If the Chief Inspector is satisfied
that in any factory or any class of factories, the use of sand or other
substance containing free silica as an abrasive in blasting is necessary for
a particular manufacture or process ( other than the process incidental or
supplemental to making of metal castings) and that the manufacture or
process cannot be carried on without the use of such abrasive ; or that
R.95)
owing to the special conditions or special method of work or otherwise
any requirement of this Schedule can be suspended either temporarily or
permanently, or can be relaxed without endangering the health of the
persons employed ; or that application of any such requirements is for
any reason impracticable or inappropriate, he may, with the previous
sanction of the State Government, by an order in writing exempt the said
factory or class of factories from such provisions of this Schedule, to such
an extent and subject to such conditions and for such period as he niay
specify in the said order.
(2) Where an exemption has been granted under sub- clause (1)
a copy of the order shall be displayed at a notice board at a prominent
place at the main entrance or entrances to the factory and also at the place
where the blasting is carried on.]
SCHEDULE IX
Liming and Tanning of Raw Hides and skins and
Processes incidental thereto
1. Cautionery notices. -- (1) Cautionary notices as to anthrax in the
form specified by the Chief Inspector shall be affixed in prominent
positions in the factory where they may be easily and conveniently read
by the persons employed.
(2) A copy of a warning notice as to anthrax in the form specified
by the Chief Inspector shall be given to each person employed when he
is engaged, and subsequently if still employed, on the first day of each
calendar year.
(3) Cautionary notices as to the effects of chrome on the skin shall
be affixed in prominent positions in every factory in which chrome
solutions are used and such notices shall be so placed as to be easily and
conveniently read by the persons employed.
(4) Notices shall be affixed in prominent places in the factory
stating the position of the "First-aid" box or cupbord and the name of the
person in charge of such box or cupboard.
(5) If any person employed in the factory is illiterate , effective
steps shall be taken to explain carefully to such illiterate person the
contents of the notices specified in paragraphs 1, 2, and 4 and if chrome
TAMIL NADU FACTORIES RULES, 1950
TAMILNADU FACTORIES RULES, 1950 [R.95
solutions are used in the factory the contents of the notice specified in
paragraph 3.
1(2. Proteenve clothing ••• The occupier shall provide and maintain
in good condition the following articles of protective clothing : --
(a) water-proof foot-wear, leg coverings, aprons and gloves for
persons employed in process involving contact with chrome solutions,
including the preparation of such solution ;
(b) gloves and boots for persons employed in lime- yard ; and
( c) protective foot-wear, aprons and gloves for persons employed
in P!Ocesses involving the handling of hides or skins, other than in
processes specified in clauses ( a) and (b) :
Provided that --
(i) the gloves, aprons, leg coverings or boots may be of rubber
or leather, but the gloves and boots to be provided under sub-clauses (a)
and (b) shall be of rubber ;
(ii) the gloves may not be provided to persons fleshing by hand
or employed in processes in which there is no risk of contact with lime,
sodium sulphide or other caustic Iiquor.]
3. Washing facilities, mess-room and eloak-reom.v- There shall be
provided and maintained in a cleanly state and in good repair for the use
of all persons employed --
( a) a trough with a smooth impervious surface fitted with a waste
pipe without plug, and of sufficient length to allow at leasH5.1 centimetres
for every ten persons employed at any one time, and having a constant
supply of water from taps or jets above the trough at intervas of not more
than 61 centimetres ; or
(b) at least one wash-basin for every ten such persons employed
at any one time, fitted with a waste pipe and plug and having a constant
supply of water together with, in either case, a sufficient supply of nail
brushes, soap or other suitable cleansing material, and clean towels ;
1 Subs. by G.O. Ms. No. 1069, dated the 29th October, 1974.
( c) a suitable mess-room, adequate for the number remaining O!}
ae premises during the meal intervals, which shall be furnished with {1)
ufficient tables and benches and {2) adequate means for warming food
nd for boiling water.
The mess-room shall (1) be separate from any room or shed in which
iides or skins are stored, treated or manipulated, (2) be separated from
he cloak-room and (3) be placed under the charge of a responsible
aerson ;
1[(d) The occupier shall provide and maintain for the use of all
persons employed, suitable accommodation for clothing put off during
working hours and another accommodation for protective clothing and
shall also make adequate arrangements for drying up the clothing in both
the cases, if wet. The accommodation so provided shall be kept clean at
all times and placed under the charge of a responsible person.]
4. Food, drinks, etc., prohibited in work-rooms. - - No food, drink,
pan and supari or tobacco shall be brought into or consumed by any
worker in any work room or shed in which hides or skins are stored,
treated or manipulated.
2[5. Medical facilities and records of examination and tests . -- (1)
The occupier of every factory to which the schedule applies, shall --
( a) employ a qualified medical practitioner for medical surveil
lance of the workers employed therein whose employment shall be
subject to the approval of the Chief Inspector of Factories ;
(b) Provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a);
(c) arrange for inspection of the hands of all the persons
keeping in contact with the Chromium substances to be made twice a
week; and
( d) provide and maintain and supply suitable ointment and
plaster in a box readily accessible to the workers and solely used for the
purpose of keeping the ointment and the plaster.
1 Subs. by G. 0. Ms. No. 1069, dated the 29th October, 1974
2
Subs. vide G.O. Ms. No. 2223, Labour and Employment, dated the 6th October,
1988.
R.95] T�L NADU FACTORJE.5 RULE.5, 1950
(2) The record of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chief Inspector of Factories, which
shall be kept readily available for inspection by the Inspector.
6. Medical Examination by Certifying Surgeon.·· (1) Every worker
employed in any of the processes to which this Schedule applies shall be
examined by a Certifying Surgeon within 15 days of his first employment.
Such examination shall include skin test for dermatoses and detection of
anthrax bacillus from local lesion by gram stain. No worker shall be
allowed to work after 15 days of his first employment in the factory unless
certified fit for such employment by the Certifying Surgeon.
, (2) Every worker employed in the said process shall be re-ex
amined by a Certifying Surgeon at least once in every 12 calendar months
and such re-examination shall, wherever the Certifying Surgeon considers
appropriate, include tests as specified in sub-paragraph (1).
(3) The Certifying Surgeon after examining a worker, shall issue
a certificate of fitness in Form 27. The record of examination and re-ex
aminations carried out shall be entered in the Certificate and the Certifi
cate shall be kept in the custody of the Manager of the Factory. The record
of each examination carried out under sub-paragraphs (1) and (2),
including the nature and the results of the tests, shall also be entered by
the Certifying Surgeon in a Health Register in Form 17.
( 4) The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker, he shall make a record of his findings in the said certificate and
the health register. The entry of his findings in those documents should
also include the period for which he considers that the said person is unfit
for work in the said processes. The person so suspended from the process
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon, in which case the
person affected shall be suitably rehabilitated. /'
(6) No person who has been found unfit to work as said in
sub-paragraph (5) above shall be re- employed or permitted to work ir
TAMILNADU FACTORIES RULES, 1950
the said processes unless the Certifying Surgeon, after further examina
tion, again certifies him fit for employment in those processes.)
SCIIEDULEX
Cellulose Spraying
1. Application • -- The provisions of this schedule shall apply to all
factories or parts of factories in which the spraying of cellulose ester
. paints, or lacquers is carried on.
2. Prohibition of the employment of children and adolescents. -- No
child or adolescent shall be employed in any factory on the operation
specified in paragraph 1 above.
3. Exhaust draughts. -- An efficient exhaust draught shall be
provided by mechanical means for the process specified in paragraph 1.
The draught Shall operate on the vapour given off in the process as near
as may be at the point of origin so as to prevent it (as far as practicable
under the atmospheric conditions usually prevailing) from escaping into
the air of any place in which work is carried on. The draught shall be
maintained working for a period of at least five minutes after the cessation
of the operation : \
Provided that the Chief Inspector may grant exemption from these
provisions if he is satisfied that due to the casual nature of the operation
they are not necessary to secure the health of the workers. _ _ .
4. Position of spary operators. - Arrangement shall, as far as
practicable, be made so as to render it unnecessary for the person
operating the spray to be in a position between a ventilating outfit and
the article being sprayed.
SCHEDULE XI
Graphite Powdering
1. Application. -- The provisions of this schedule shall apply to all
factories or parts of factories in which the grinding and sieving of graphite
and the processes incidental thereto are carried on.
2. Prohibition of employment of women, children and adolescents.
-- No woman, child or adolescent shall be employed in any factory upon
any of the operations specified in paragraph 1 above.
R. 95] TAMILNADU FACTORIES RULES, 1950
3. Medical certificates and examinations. -- (1) No person shall be
employed in any factory for more than fifteen days in the year upon any
of the operations specified in paragraph 1 above unless a special certifi
cate of fitness in Form No. 27, granted tohim by a Certifying Surgeon
appointed under section 10, is in the custody of the man�ger of the factory.
(2) The Inspector of Factories may require that any person in
respect of whom a certificate referred to in sub-paragraph (1) has been
granted shall carry with him while at work a token giving reference to such
certificate.
{3)Every person so employed shall be medically examined by a
Certifying Surgeon at intervals of not more than six months and a record
of such examination shall be entered in the special certificate granted
under sub-paragraph (1).
( 4) If at any time a Certifying Surgeon is of opinion that any person
is no longer fit for employment upon any of the operations specified in
paragraph 1 above he shall cancel the, special certificate of fitness granted
to that person.
(5) No person whose special certificate of fitness has been can
celled shall be employed upon any of the operations specified in para
graph 1 above unless a Certifying Surgeon again certifies him to be fit.
4. Exhaust draught. -· Provisions shall be made for removing the
dust produced in any of the operations specified in paragraph 1 above by
means of an efficient exhaust draught so contrived as to operate on the
dust as closely to the point of origin as possible :
Provided that where the provision of an exhaust draught is not
reasonably practicable the Inspector may require --
( a) respirators of a type approved by him to be provided and
maintained in a clean and efficient condition by the occupier and worn
by every person working under such conditions ; and
. (b) the damping of floors, apparatus and material to prevent the
raising of dust.
S. Floor and work benches. •• (1) The floor of every room in which
any person is employed upon any of the operations specified in para
graph 1 above shall be of cement or other impervious material.
TAMIL NADU FACTORIES RULES, 1950 [R.95
(2) The top of every work-bench in every such room shall be of
impervious material.
(3) The said floors and work-benches shall be kept clean and in
good condition.
( 4) The Inspector may, by order in writing, require the said floors
and work-benches to be kept wet in such manner as he may deem suitable,
in order to reduce dust.
6. Washing facilities. •• The occupier shall provide and maintain in
a clean state and in good repair for the use of persons employed upon
any of the operations specified in paragraph 1 above either ( a) a trough
with smooth impervious surface fitted with a waste-pipe without plug, and
of sufficient length to allow at least 61 centimetres for every five such
persons employed at any one time and having a constant supply of water,
from taps or jets above the trough at intervals of not more than 61
centimetres, or (b) at least one lavatory basin for every five such persons
employed at any one time, fitted with a waste pipe and plug having a
constant supply of water, together with, in either case a sufficient supply
of nail brushes, soap or other suitable cleaning material and clean towels.
7. Food, drink, and tobacco. -· No food, drink, pan \nd supari or
tobacco shall be brought into, or consumed, in any room in which any
person is employed upon any of the operations specified in paragraph 1
above.
8. Protective clothing. --Adequate protective clothing such as over
alls in a clean condition shall be provided by the occupier to every person
employed upon any of the operations specified in paragraph 1 above.
9, Exemptions. •• The Chief Inspector may exempt any factory or
part of a factory from the provisions of paragraphs 4 to 7 to the extent he
deems suitable, if he is satisfied that their observance is not necessary for
safeguarding the health of the operatives.
SCHEDULE XII
Printing Press and Type Foundries - Cettain lead
process carried on therein
1. Exemptions. •• Where the Chief Inspector is satisfied that all
or any/of the provisions of this schedule are not necessary for the
R.95] TAMILNADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 [R.95
protection of persons employed he may by certificate in writing exempt
any factory from all or any of such provisions subject to such conditions
as he may specify therein. Such certificate may at any time be revoked by
the Chieflnspector.
2. Definitions. -- In these regulations --
'Lead material' means material containing not less than 5 per cent.
of lead.
'Lead process' means --
(a) the melting of lead or any lead material for casting and
mechanical composing ;
(b) the recharging of machines with used lead material ; or
(c) any other work including removal of dross from melting
pots, cleaning of plungers ; and
(d) manipulation, movement or other treatment of lead
material.
'Efficient exhaust draught' means localized ventilation effected
by heat or mechanical means for the removal of gas, vapour, dust or fumes
so as to prevent them from escaping into the air of any place in which
work is carried on. No draught shall be· deemed efficient which fails to
remove gas, vapour, fume or dust at the point where they originate.
3. Exhaust draught. -- None of the following processes shall be
carried on except with an efficient exhaust draught : -
(a) melting lead material or slugs;
(b) heating lead material so that vapour containing lead is given
off; or
unless carried on in such a manner as to prevent free escape of gas,
vapour, fumes or dust into any place in which work is carried on ; or
unless carried on in electrically heated and thermostatically control
led melting pots.
Such exhaust draught shall be effected by mechanical means and so
contrived as to operate on the dust, fume, gas or vapour given off as closely
as may be at its point of origin.
4. Prohibition relating to women andyoung persons. •• No woman
or young person shall be employed or permitted to work in any lead
process.
5. Separation of certain processes.» Each of the following processes
shall be carried on in such a manner and under such conditions as to
secure effectual separation from one another and from any other
process: --
(a) melting of lead or any lead material;
(b) casting of lead ingots ;
(c) mechanical composing.
6. Container for dross. -- A suitable receptacle-with tightly fitting
cover shall be provided and used for dross as it is removed from every
melting pot. Such receptacle shall be kept covered while in the work-room
near the machine except when the dross is being deposited therein.
7. Floor of workroom. --The floor of every work- room where lead
process is carried on shall be --
(a) of cement or similar material so as to be smooth and imper
vious to water ;
(b) maintained in sound condition ; and
(c) shall be cleansed throughout daily after being thoroughly
damped with water at a time when no other work is being carried on at
the place.
8. Mess room. -- There shall be provided and maintained for the use
of all persons employed in a lead process and remaining on the premises
during the meal intervals, a suitable mess -room which shall be furnished
with sufficient tables and benches.
9. Washing facilities. •• There shall be provided and maintained in
a cleanly state and in good repair for the use of all persons employed in
a lead process,
R.95] TAMIL NADU FACTORIES RULES, 1950
TAMILNADUFACTORIESRULES, 1950 [R.95
(a) a wash place with either -
(i) a trough �ith smooth impervious surface fitted with a waste
pipe without plug, and of sufficient length to allow at least 61 centimetres
for every five such persons employed at any one time and having a
constant supply of water from taps or jets above the trough at intervals of
not more than 61 centimetres ; or
(ii) at least one wash basin for every five such persons employed
at any one time, fitted with a waste pipe and plug and having an adequate
supply of water laid on or always readily available ; and
(b) a sufficient supply of clean towels made of suitable material
renewed daily with a sufficient supply of soap or other suitable cleaning
material.
1(10. Medical facilities and records of examination and tests. -- (1)
The occupier of every factory to which the schedule applies, shall --
( a) employ a qualified medical practitioner for medical surveil
lance of the workers employed therein whose employment shall be
subject to the approval of the Chief Inspector of Factories ; and
(b) provide to the said medical practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The record of medical examinations and appropriate tests
carried out by the said medical practitioner shall be maintained in a
separate register approved by the Chieflnspector ofF actories which shall
be kept readily available for inspection by the Inspector.
10-A. Medical Examination by Certifying Surgeon • -- (1) Every
worker employed in a lead process shall be examined by a Certifying
Surgeon within 15 days of his first employment. Such examination shall
include tests for lead in urine and blood, ALA in urine, haemoglobin,
stippling of cells and steadliness tests. No worker shall be allowed to work
after 15 days of his first employment in the factory unless certified fit for
such employment by the Certifying Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every six calendar months.
1 Subs. vide G.O. Ms. No. 2223, L & E, dated the 6th October, 1988.
Such re- examination shall, wherever the Certifying Surgeon considers
appropriate, include tests as specified in sub-paragraph (1).
(3) The Certifying Surgeon after examining a worker, shall issue
certificate of fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub- paragraphs (1)
and (2), including the nature and the results of the tests, shall also be
entered by the Certifying Surgeon in a Health Register in Form 17.
( 4) The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of the
worker, lie shall make a record of his findings in the said certificate and
the health register. The entry of his findings in those documents should
include the period for which he considers that the said person is unfit for
work in the said processes. The person so suspended from the process
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon, in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in
sub-paragraph (5) above shall be re- employed or permitted to work in
the said process unless the Certifying Surgeon, after further examination,
again certifies him fit for employment in those processes.]
11. Food, drinks, etc., prohibited in work rooms. -- No food, drink,
pan and supari or tobacco shall be consumed or brought by any worker
into any work-room in which any lead process is carried on.
SCHEDULE XIII
Cashew-nut processing
. 1. Application. •• The provisions of this schedule shall apply to all
factories in which roasting, scrubbing or shelling of cashew-nuts or ex
tracting oil from cashew- nuts or cashew-nuts shells is carried on.
R.95] TAMIL NADU FACTORIES RULES, 1950
TAMIL NADU FACTORIES RULES, 1950 (R.95
2. Prohibition of employment of women and young persons. -- No
woman or young person shall be employed in any of the processes
specified in paragraph 1 except in shelling of roasted cashew-nuts.
3. Protective clothing and equipment. - The occupier shall provide
and maintain --
(i) for the use of all persons employed in roasting or scrubbing of
cashew-nuts or extracting oil from cashew-nuts or cashew- nuts shells --
(a) suitable rubber or washable leather gloves,
(b) suitable impervious aprons with sleeves to cover the body
down to the knees and shoulders, and
(c) suitable foot-wear to afford protection to the feet and legs
against cashew-nut oil ;
(ii) for the workers employed in cashew- nut shelling, either, -
(a) protective ointment containing 10 per cent. of shellac, 55
per cent. of alcohol, 10 per cent. of sodium perborate, 5 per cent. of
carbitol and 20 per cent. of talc, or
(b) a sufficient quantity of kaolin and coconut oil ; and
(iii) any other material or equipment which the Chief Inspector
of Factories may deem to be necessary for the protection of the workers.
4. Use of protective clothing and equipment. -- Every person
employed in the processes specified in paragraph 1, shall make use of the
protective clothing and equipment supplied and arrangement shall be
made by the occupier to supervise their maintenance and cleanliness.
S. Disposal of shells, a'shes or oil of cashew-nut.,» (i) Shells, ashes
or oil of cashew-our· shall not be stored in any room in which workers are
employed and shall be removed atleast twice a day to any pit or enclosed
place in the case of shells and ashes and to closed containers kept in a
separate room in the case of oil. ·
(ii) No worker shall be allowed to handle shells or oil of cashew·
nut without using the protective measures provided in paragraph 3.
' I
6. Floors of work-rooms. •• The floor of every work-room in which
the processes specified in paragraph 1 are carried on shall be of a hard
material so as to be smooth and impervious and of even surface and shall
be cleaned daily ; and spillage of any cashew- nut oil in any work-room
shall be washed with soap and cleaned immediately.
7. Seating..accommodation. -- Workers engaged in shelling of
cashew-nuts.shall be provided with adequate seats of work benches which
shall be cleaned daily.
8. Mess-room. -- (a) There shall be provided and maintained for the
use of all persons employed in the processes specified in paragraph 1, a
suitable rest room furnished with a sufficient number of tables and chairs
or benches;
(b) Separate lockers shall be provided where food, etc., shall be
stored by workers before it is consumed in the rest room.
9. Food, drinks, etc., prohibited in work-rooms.·· No food, drink,
pan, supari or tobacco shall be brought or consumed by any worker in
any room in which the processes specified in paragraph 1 are carried out
and no person shall remain in any such room during intervals for meals
or rest.
10. Washing facilities. -· Where roasting, scrubbing and shelling of
cashew- nuts or extracting oil from cashew-nuts or cashew-nuts shells is
carried on, there shall be provided and maintained, in clean and good
'repair, washing facilities, at the scale of one tap or stand pipe for every
ten workers the taps or stand pipes being spaced not less than 4 feet apart
and also a sufficient supply of soap, coconut oil, nail brushes and towels.
11. Time allowed for washing. •• Before each meal and before the
end of the day's work at least ten minutes, in addition to the regular meal
times, shall be allowed to any person employed in the process specified
in paragraph 1, for the purpose of washing.
12. Smoke or gas produced by roasting cashew-nuts. -- Where
smoke or gas is produced in the operation of roasting, provision shall be
made for removing the smoke or gas through a chimney of sufficient
height and capacity or by such other arrangements as may be necessary
to prevent the gas or smoke from escaping into the air or any place in
which workers are employed.
R.95] TAMILNADUFACTORIESRULES, 1950
[R.95
13. Storage of protective equipment. --A suitable room or a portion
of the factory suitably partitioned off, shall be provided exclusively for the
storage of all the protective equipment supplied to the workers and no
such equipment shall be stored in any place other than the room or place
so provided.
1[14. Medical facilities and records of examinations and tests. - (1)
The occupier of every factory to which the schedule applies, shall --
( a) employ a qualified Medical Practitioner for medical sur
veillance of the workers employed therein whose employment shall be
subject to the approval of the Chief Inspector of Factories ; and
(b) provide to the Medical Practitioner all the necessary
facilities for the purpose referred to in clause (a).
(2) The said Medical Practitioner shall inspect daily the hands
and feet of all the persons employed in the processes specified in para
graph 1.
· (3) The record of such examinations carried out by the Medical
Practitioner shall be maintained in a separate register approved by the
Chief Inspector of Factories, which shall be kept readily available for
inspection by the Inspector.
(4) The first-aid box maintained. shall also containBurrough's
Solution (1 : 20) and aqueous solution of tannic acid (10%) for treatment
of cases of dermatitis.
14A. Medical Examination by Certifying Surgeon • -- (1) Every
worker employed in the processes specified in paragraph (1) shall be
examined _py a Certifying Surgeon within 15 days of his first employment.
Such examinations shall include skin test for dermatitis and no worker
shall be allowed to work after 15 days of his first employment in the factory
unless certified fit for such employment by the Certifying Surgeon.
(2) Every worker employed in the said processes shall be re-ex
amined by a Certifying Surgeon at least once in every three calendar
months. Such examinations shall, wherever the Certifying Surgeon con
siders appropriate, include asking test for dermatitis.
1Subs. vide G.O. Ms. No. 2223, L & E, dated the 6th Oc!ober, 1988.
TAMILNADUFACTORIESRULES, 1950
R.95] TAMIL NADU FACTORIES RULES, 1950
(3) The Certifying Surgeon after examining a worker, shall issue
a certificate of fitness in Form 27. The record of examination and re
examinations carried out shall be entered in the Certificate and the
Certificate shall be kept in the custody of the Manager of the Factory.
The record of each examination carried out under sub-paragraphs (1)
and (2), including the nature and the results of these tests, shall also be
entered by the Certifying Surgeon in a Health Register in Form 17.
( 4)The certificate of fitness and the health register shall be kept
readily available for inspection by the Inspector.
(5) If at any time the Certifying Surgeon is of the opinion that a
worker is no longer fit for employment in the said processes on the ground
that continuance therein would involve special danger to the health of
worker, he shall make a record of his findings in the said certificate and
the Health Register. The entry of his findings in those documents should
.also include the period for which he considers that the said person is unfit
to work in the said processes. The person so suspended from the process
shall be provided with alternate placement facilities unless he is fully
incapacitated in the opinion of the Certifying Surgeon, in which case the
person affected shall be suitably rehabilitated.
(6) No person who has been found unfit to work as said in
sub-paragraph (5) shall be re-employed or permitted to work in the said
processes unless the Certifying Surgeon, after further examination, again
certifies him fit for employment in those processes.]
15. Exemption. --The Chieflnspector of Factories may grant exemp
tion from the operation of any of these provisions where he is satisfied
that their observance is not necessary for safeguarding the health of
workers.
SCHEDULE XIV
Dyeing, stencilling and painting of mats, mattings and
carpets in coir and fibre factories.
1. Application. -- These provisions shall apply to all coir factories in
which stencilling or painting of mats or mattings or carpets is carried on,
and to all coir and fibre factories in which dyeing of yarn ( other than
cotton yarn) and fibre is carried on.
[R.95
2. Prohibition of employment of women and young persons.·· No
woman or young person shall be employed or permitted to work in any
of the operations specified in clause 1.
3. Protective measures. •• The occupier shall provide free of cost and
maintain in a good condition for use of all persons engaged in the
operations specified in clause 1 --
(a) suitable rubber gloves of durable quality for both hands ;
/
(b) rubber boots of durable quality for both legs ;
(c) goggles; and
(d) any other material or appliance which in the opinion of the
Chief Inspector shall be necessary for the protection of workers.
4. Wearing of gloves, boots and goggles. •• All persons engaged in
any of the operations specified in clause 1, shall while at work in those
processes, make use of the materials and appliances provided under
clause 3.
5. JFood and drink. •• No food or drink shall be brought into or
consumed in, in any room in which any of the operations specified in
clause 1 is carried on.
' 6. lFloor of work-rooms. a. The floor of every room in which any of
the operations specified in clause 1 is carried on shall be --
(a) of cement or similar material so as to be smooth and imper
vious to water ;
(b) maintained in sound condition ; and
(c) provided with suitable and adequate arrangement for
drainage.
7. Washing facilities. •• (i) The occupier shall provide and maintain
for the use of all persons employed in operations specified in clause 1,
suitable washing facilities consisting of : --
(a) a masonry or steel water tank capable of holding sufficient
water and having taps at the rate of one tap for every ten persons
employed at any one time, the floor around the tank and below the taps
being cement plastered and maintained in sound and clean condition and
TAMIL NADU FACTORIES RULES, 1950
R.95] TAMILNADUFACTORIESRULES, 1950
suitable and adequate arrangements for drainage being provided around
the tanks and the taps ;
(b) sufficient supply of nail brushes, non-irritable soap or other
suitable cleansing materials and clean towels.
(ii) The facilities so provided shall be placed under the charge of
a responsible person and shall be kept clean.
(iii) The following method shall be adopted in removing dye from
the hands of employees and the occupier shall make readily available in
the premises of the factory all the chemicals required for the purpose in
the specified proportion : --
(a) wash with sulphonated oil followed by water ;
(b) wash in 1 to 2000 solution of potassium permanganate ;
(c) wash in two per cent. solution of sodium hydrosulphite or
in two per cent. solution of sodium bisulphite ;
(d) wash in water ; and
(e) application oflanolim cream.
Note : No person shall be allowed to use turpentine, petroleum,
distillates, bleaching powder and other bleaches for removing dirt and
dye from his hands.
8. Medical examination. •• (1) Every person employed in any of the
operations specified in clause 1 shall be medically examined by a Certify
ing Surgeon within fourteen days of his first employment in such opera
tions and thereafter shall be examined by the Certifying Surgeon at
intervals of not more than twelve months and a record of such examina
tions shall be entered by the Certifying Surgeon in the Health Register in
Previous and next
Questions people ask
Is form OF CERTIFICATE OF COMPETENCY ISSUED TO A of the Tamil Nadu Factories Rules,1950 still in force?
No repeal of the Tamil Nadu Factories Rules,1950 is recorded.