LawGrids logoLAWGRIDS.ORG

Appendix, The Tamil Nadu Factories Rules,1950: APPENDIX

The Tamil Nadu Factories Rules,1950 - Appendix

Text of appendix

APPENDIX

APPENDIX (See Paragraph 4) CAUTIONARY NOTICE Insecticides and pesticides. 1. Chemicals handled in this plant are poisonous substances. 2. Smoking, eating food or drinking, chewing tobacco in this area is prohibited. No food stuff or drink shall be brought in this area. 3. Some of these chemicals may be absorbed through skin and may cause poisoning. 4. A good wash shall be taken before meals. 5. A good bath shall be taken at the end of the shift. _ 6. Protective clothing and equipment supplied shall be used while worlong in this area. 7. Containers of pesticides shall not be used for keeping food stuffs. 8. Spillage of the chemicals on any part of the body or on the floor or work bench shall be immediately washed away with water. 9. Clothing contaminated due to splashing shall be removed immediately. 10. Scrupulous cleanliness shall be maintained in this area. 11. Do not handle pesticides with bare hands ; use scoops provided with handle. 12. In case of sickness like nausea, vomitting, giddiness, the manager should be informed who will make necessary arrangements for treatment. 13. All workers shall report for the prescribed m�dical tests regularly to protect their own health.] 1[SCHEDULE XXX: Manufacture of Rayon by viscose process 1. Definitions. -- For the purpose of this schedule -- (a) "approved" means approved for, the time being in writing b the Chief Inspector ; 1 Iris. by G.O. Ms. No. 1717, Labour, dated the 2nd September, 1986. TAMll, NADU FACTORIES RULES, 1950 [R.95 R.95] TAMIL NADU FACTORIES RULES, 1950 (b) ''breathing apparatus" means a helmet or face piece with necessary connections by means of which the person using it in a poisonous, asphyxiating or irritant atmosphere breathes unpolluted air ; or any other approved apparatus ; ( c) "churn" means the vessel in which alkali cellulose pulp is treated with carbon disulphide ; (d) "dumping'' means transfer of cellulose xanthate from a dry churn to a dissolver ; (e) "efficient exhaust draught" means a localised ventilation by meachanical means for the removal of any gas or vapour, so as to prevent it from escaping into the air or any place in which work is carried on. No draught shall be deemed to be efficient if it fails to control effectively any gas or vapour generated at the point where such gas or fume originates ; (f) "fume process" means any process in which carbon disulphide or hydrogen sulphide is produced, used or given off; (g) "life belt" means a belt made of leather or other suitable material which can be securely fastened round the body with a suitable length of rope attached to it, each of which is sufficiently strong to sustain the weight of a man ; (h) "protective equipment" means apron, goggles, face shields, footwear, gloves and overalls made of suitable materials. 2. Ventilation. -- (1) In all workrooms where a fume process is carried on, adequate ventilation by natural or mechanical means shall be provided so as to control, in association with other control measures, the concentration of carbon-disulphide and hydrogen sulphide in the air of every work environment within the permissible limits. (2) Notwithstanding the requirements in sub-paragraph (1), an effi­ cient exhaust draught shall be provided and maintained to control the concentration of carbon-di-sulphide and hydrogen sulphide in the air at the following locations : -- (a) dumping hoppers of dry churns; (d) hydro-extractors for yarn cakes ;, (e) after treatment processes; and (f) spin baths. [R.95 (3) In so far as the spinning machines and trio rollers and cutters used in staple fibre spinning are concerned, they shall be, for the purpose of ensuring the eff ectiveness of the exhaust draught to be provided as required in sub-paragraph (1), enclosed as fully as practicable and provided with suitable shutters in sections to enable the required opera­ tions to be carried out without giving rise to undue quantities of carbon­ di-sulphide and hydrogen sulphide escaping to the work environment. ( 4) No dry churn shall be opened after completion of reaction without initially exhausting the residual vapours of carbon-di- sulphide by operation of a suitable and efficient arrangement for exhausting the vapours which shall be continued to be operated as long as the churn is kept opened. (5) Whenever any ventilation apparatus normally required for the pupose of meeting the requirements in sub-paragraphs (2), (3) and ( 4) is ineffective, fails, or is stopped for any purpose whatsoever, all persons shall be required to leave the work areas where the equipment or proces­ ses specified in the above said sub- paragraphs are in use, as soon as possible, and in any case not later than 15 minutes after such occurrence. ( 6) (i) All ventilating systems provided for the purposes as re­ quired in sub-paragraphs (2), (3) and ( 4) shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examinations of test shall be rectified forthwith. (ii) A register containing particulars of such examinations and tests, and the state of the systems and the repairs or alterations (if any) found to be necessary shall be kept and shall be available for inspection by an Inspector. TAMIL NADU FACTORIES RULES, 1950 (b) spinning machines ; (c) trio rollers and cutters used in staple fibre spinning; 3. Waste from spinning machines. -- Waste yarn from the spinning machines shall be deposited in suitable containers provided with close fitting covers. Such waste shall be disposed off as quickly as possible after decontamination. 4. Linking of dry churns. -- The inside surface of all dry churns shall be coated with a non-sticky paint so that cellulose xanthate will not stick to the surface of the churn, such coating shall be maintained in good condition. '" 5. Air monitoring. -- (1) To ensure the effectiveness of the control measures, monitoring of carbon-di-sulphide and hydrogen sulphide in air shall be carried out once at least in every shift and the record of the results so obtained shall be entered in a register specially maintained for the purposes. (2) For the purpose of the requirement in sub-paragraph (1), instantaneous gas detector tubes shall not be used. Samples shall be collected over a duration of not less than 10 minutes and analysed by an approved method. The locations where such monitoring is to be done shall be as directed by the Inspector. (3) If the concentration of either carbon disulphide or hydrogen sulphide exceeds the permissible limits for such vapour or gas as laid down in Rule 102A suitable steps shall be taken for controlling the concentrations in air of such containers. A report of such occurrences shall be sent to the Chief Inspector forthwith. 6. Prohibition to remain in fume process room. -- No person during his intervals for meal, or rest shall remain in any room wherein fume process is carried on. 7. Prohibition relating to employment of young persons. -- No young person shall be employed or permitted to work in any fume process or in any room in which any such process is carried on. 8. Protective equipment. -- (1) The occupier shall provide and maintain in good condition protective equipment as specified in the Table for use of persons employed in the processes referred lo therein. R.95] TAMIL NADU FACTORIES RULES, 1950 5 1 4 TAMIL NADU FAleuEs Rum, 1950 [R35 THE TABLE Pi-acers PrDIEL‘IDIFrIqmpmz/nl (l) (2] l. Dumping Overalls, face-shields, gloves and font~ wear - all made ofsuitable material. 54 Spmmng Suitable aprons, gloves and footwear. 3. Piocess involving or likely to invnlve contact with viscose solulmn. Suitable gloves and footwear 4. Handling of Sulphur Suitable Chemical goggles. 5). Any orher process Protective equipment as may he involving cunlact With directed by the Chief Inspector by an hazardous chemicals. order in writing. (2) A suitable mom, rooms or lockersshall be provided exclusive- ly for the storage of all the protective equipment supplied to workers and no such equipment shall be stored at any place other than the mom; rooms or lockers so provided. 9. Breathing apparatus. <- (1) There shall be provided in every factory where l‘ume process is carried on, sufficient supply of, (a) hrearhing apparatus ; ()5) oxygen and suitable appliances for its administration ; and (c) life bells. K (2) (i) The breathing apparatus and other appliances referred to in sub-paragraph (1) shall be maintained in good condition audkept in appropriate locations so as to be readily available. (ii) The breathing apparatus and other applicances referred to in clauses (a) and (b) of sub-paragraph (1) shall be cleaned and disin- IF ,_. v. ,.~,,.,W...,... .VMM ._.s_.._ 11.95] TAMIL Nanu FAEromFs RULES, 1950 5 1 5 tested at suitable intervals and thoroughlyinspea‘ed once ewry month bya responsible rim-son. (iii) A record of the maintenance and of the condition of thebreathing apparatus and other appliances referred to in sub- clause (1)shall be entered In a register provided for that purpose which shall be readily available for inspection by an Inspector. (3) Srufficientnumber ofworkers shall be trained and periodicallyretrained in the use of breathing apparatus and administering artificialrespiration so that at least two such trained persons would be availableduring all the working hours in each room in which fume process iscarried on. (4) Breathing apparatuswshall be kept properly labelled in clean,dry. light proof cabinets and,if‘liable to be affected by fumes, shall beprotected by placing them‘in suitable containers. ‘ (5) No person shall be employed to perform any work specifiedin sub-paragraph (1) for which breathing apparatus is necessary to beprovided under that sub-paragraph unless he has been fully instructed inthe proper use of that equipment. ' (6) No breathing apparatus provided in pursuance of sub~para-graph (1) which has been worn by a person shall be worn by another person unless it has been thoroughly cleaned and disinfected since lastbeing worn and the person has been fully instructed in the proper use ofthat eqiupment. rarbon—di-sulphide is produced, used or given off or is likely to be g‘venoff into Ihe work environment, other than a spinning room, shall be of flame—proof construction and all electric conductors shall either beenclosed in metal conduits or be lead sheathed. 11. Prohibition relating to smoking, etc. —- No person shall smoke or tarry matches, fire or naked light or other means of producing a nakedlight or spark in a room in which fume process is carried on. A notice inthe language understood by the majority of the workers shall be posted 5'5 THE TAMIL NADU FACTORIES RULES, ‘950 [R35 in prominent locations in the plant prohibiting smoking and carrying of matches. fire or naked light or other means of producing naked light or spark into such rooms : Provided that fire. naked light or other means of producing a naked light or spark may be carried on in such room only when required for the purpose of the process itself under the direction of a responsible person. 12. Washing and bathing facilities. — (l) There shall be pro- vided and maintained in a clean state and in good repair for the use ofall workers employed in the processes covered by the schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 25 persons employed. (2) The washing places shall have stand pipes placed at intervals of not less than one metre. (3) Not less than one halfof the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable material shall be provided 2 Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply ofsoap and nail brushes shall be provided. 13. Res! roam. — (1) A rest room shall be provided for the wor» kers engaged in doffing operations of filament yam spinning process. (2) Such rest room shall be provided with fresh air supply and adequate seating alrangement. 14. Cautionary notice and instructions * (l) The following cautionary notice shall be prominently displayed in each time process room : — CAUTIONARY NOTICE 1. Carbon disulphide (CS) and Hydrogen Sulphide (1-123) which _ may be present in this room are hazardous to health. 2. Follow safety instructions. required. a. Use protective equipment and breathing apparatus as and when I R.95] THE TAMIL NADU FACTDRIES RULES. 1950 517 4. Smoking is strictly prohibited in this area. This notice shall be in a language understood by the majority of the workers and displayed where it can be easily and conveniently read. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents ofthe notice so displayed. (2) Arrangements shall be made to instruct each worker employed in any room in which a fume process is carried on regarding the health hazards connected with their work and the preventive measures and methods to protect themselves. Such instructions shall be given on his first employment and repeated periodically. (3) Simple and special instrumions shall be framed to ensure that effective measures will be carried out in case of emergency involving escape ofcarbon disulphide and hydrogen sulphide. These instructions shall be displayed in the concerned areas and workers shall be instructed and trained in the actions to be taken in such emergencies. 15. Medical facilities and records of examinations and tests. —— (l) The occupier of each factory to which the schedule applies, shalli (a) employ a qualified medical officer for medical survei- llance of the workers employed in the fume process whose employment shall be subject to the approval ofthe Chief Inspector of Factories ; and (b) provide to the said medical officer all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examination and appropriate tests carried out by the said medical officer shall be maintained in a separate register approved by the Chief Inspector “Factories. which shall be kept readily available for inspection by the Inspector. Ifir Medical Examination by the Certifying Surgeon. — (1) Every worker employed in the fume process shall be examined by a Certifying Surgeon within 15 days of his first employmentl Such examination shall include tests for estimation of exposure co-efficient (iodine azide test in urine) and cholesterol, as well as Electrocardiogram (ECG) and Central Nervous System (CNS) tests. No worker shall be allowed to work afier 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the fume process shall be re- examined by a Certifying Surgeon at least once in every twelve calendar 518 THE TAMIL NADU FACTORIES RULES, 1950 [12.95 months Such examination shall wherever the Certifying Surgeon consi- ders appropriate, include all the tests as specified in sub-paragraph (l). (3) The Certifying Surgeon after examining a worker, shall issue a certificate of fitness in Form 27. The record of re-examinations carried out shall he entered in the certificate and the cem'ticate shall he kept in the custody of the Manager of the factory. The record ofeach examination carried out shall he entered in the certificate and the certificate shall he kept in the custody of the Manager of the factory. The records of each examination carried out under sub-paragraphs (l) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17A. (4) lite Certificate or Fitne§ and the health register shall be kept readily available for inspection by the Inspector. (5) [f at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the fume process on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health registen The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the fume process. 1[The persons so suspended from the process shall be provided with alternative placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon in which case the person affected shall be suitably rehabilitated] (6) No person who has been found unfit to work as said in sub- paragraph (5) above shall be re-employed or permitted to work in the fume process unless the Certifying Surgeon, after further examination again certifies him fit for employment in such process. I 7. Emmptinns. ~ If in respect ofany factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief inspector may, by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such omiditions, if any, as he may specify therein Rigs] THE TAMIL NADU FACTORIES RULES, 1950 519 ‘[SCHEDULE XXXI Flammable Liquefied or compressed gases and highly flammable liquids. 1. Application. — Provisions of this Schedule shall apply to all factories where flammable liquefied or compressed gases or highly flammable liquids are manufactured, stored, handled used (sic). 2. Definitions. — For the purposes of this Schedule, h (a) “ bulk storage ” means bullet or horton sphere or mounded vessel used for storage of flammable liquefied or compressed gases or highly flammable liquids, which are having capacity exceeding one thousand litres ofwater capacity ; (b) “ bullet ” means a horiZOntal cylindrical pressure vessel with hemispherical or dished ends used for storage of flammable liquefied or compressed gas ; (c) “ explosive mixture ” means a mixture of combustion agent (oxidising substance in gaseous, liquid or solid state) and a fuel (oxidisable substance in gaseous, liquid or solid state) in such proportions that it could give rise to a very rapid and violent oxidation reaction, liberating more kinetic energy than is dissipated through conduction and convection, ultimately causing practical effect of explosion ; (d) “ fire proof ” means a passive means of protection of a structure or equipment or vessel from exposure to direct fire or flame impingement or prolonged exposure to high intensity radiant thermal flux, by the application of a coating of certain heat-resistant substance or mixture of a specified rating ; (e) “ fire safe ” means a provision of dual seating to control leakage to acceptable level, even afier damage, due to fire, as applied to valves ; (f) “ flammable compressed gas ” means flammable compressed gas as defined in rule 2 of the Static and Mobile Pressure Vessels (Unfired) Rules, 1981 framed under the Explosives Act, 1884 (Central Act [V of 1884) ; ' Subsr by 0.0 Ms. No. ”0, Labour and Employment (M-Z), dated the 16th September, 2008. 520 THE TAMlL NADU FACTORIES RULES, I950 [R35 (g) “ flammable liquefied gas ” means a flammable gas kept in liquefied state by the application of pressure at normal ambient temperature, 13% (thirteen percentage) or less of which by volume with air forms a flammable mixture or which has a flammable range with air of atleast 12% (twelve percentage) points regardless of the lower flammable limits; (h) “ gas free ” means a condition when the concentration of a flammable gas in an equipment or a vessel is well below the threshold limits (lower explosive limit), so, that it is safe for a man to enter into the equipment or vessel or to conduct “ hot work ” there, as the case may be ; (i) “ highly flammable liquid ” means any liquid including its solution, emulsion or suspension which when tested in a manner specified by sections 14 and 15 of the Petroleum Act, 1934 (CentralAct XXX of 1934) gives off flammable vapours at a temperature less than 32 degrees Centigrade ; (j) “ Horton sphere ” means a spherical Pressure Vessel, supported vertically and is used for the storage of flammable liquefied' or compressed gas ; (k) “ hot work ” means an activity which may produce enoughheat or spark to ignite a flammable or explosive mixture ; (l) “ Mounded vessel ” means a pressure vessel for the storage of flammable liquefied or compressed gas, which is sited above ground and is completely covered by a mound of earth or similar inert material except for nozzles, manhole covers, inspection covers fitted onthe top of the vessel ‘, (m) “ purging ” means an act of replacing the atmosphere inside a vessel or a container by an inert gas in such a manner as to prevent theformation ofan explosive mixture. (n) “ purging into service ” means the replacement of air in aclosed system by an inert gas and then replacement of the inert gas bythe flammable gas, vapour or liquid ; (o) “ purging out of service ” means the replacement of normalflammable content of a closed sy ' rcplacement of the inert gas by air and safe for any person to work ; u R.95] THE TAMIL NADU FACTORIES RULES, 1950 (p) "remote operated emergency valve" means a shut-off valve capable of remote operation which closes automatically on loss of the actuatmg power or fite engulfment and which is fire-safe. 3. Storage. - Every highly flammable liquid, flammable liquefied or compressed gas used in every factory shall be stored in bulk in suitable fixed storage tank made of adequate fire-resistant costruction and located in a safe position under the ground or in the open. 4. Location and spacing. - Before siting the location of any storage ves \ risk analysis study shall be carried out. Based on the risk analysis w.i.df, every storage vessel shall be located in the manner specified below : - (a) the location shall not interfere with the movement of vehicles. The Risk Contour shall not intercept the public places such as assembly points, canteen, rest sheds and similar other locations ; (b) before locating any storage vessel, the soil condition shall be assessed for the suitability of the superstructure ; ( c) the storage vessel shall be sited above ground in open air and well-ventilated place ; (d) mounded vessels shall be so located that the manholes and pressure relief valves are in a well-ventilated position; ( e) the minimum safety distance between the storage vessels and from buildings, boundary or fixed ignition source shall be in accordance with the Static and Mobile Pressure Vessels (Unfired) Rules, 1981, as amended from time to time ; (f) the storage vessels shall not be installed one above the other; (g) the bullets shall be so located that their longitudinal axes do not points towards other vessels, vital process equipment, control rooms, loading stations, nearby buildings or storage tanks containing hazardous materials: (h) weeds, long grass, deciduous shrubs and trees and an) combustible materials shall be removed from the storage vessel area withir the licensed premises ; (i) the storage vessels shall not be located within the bunded enclosure of any heat source or other flammable liquids, gases or oxidizers; G) the storage vessels, pumping equipment, loading and unloading facilities and vapourisers shall be located in an exclusive fenced compound of atleast 2 metres high along the perimeter of the safety zone ; such fenced compound shall have atleast two gates for the safe exit of persons and vehicles in case, of any emergency ; (k) the number of storage vessels in one group shall not exceed six; (I) storage vessels within a group shall be so located that their longitudinal axes are parallel to each other ; (m) spheres and bullets shall not be grouped together and shall oe provided with separate piping manifold, so as to avoid overfilling of a vessel due to gravitation from the other ; (n) the top surface of the storage vessels installed in a group shall be on the same plane so that the pressure safety valve blow-out from them do not affect the other ; (o) the flooring of the bullets or spheres shall be sloped in such a way that the spilled liquid or gas from any vessel shall not pass through any other vessel ; (p) the storage vessels shall not be located in such a way that the high tension electrical cables shall not pass through or near the licensed premises ; (q) storage vessels shall not be sited in places which are susceptible to flooding ; (r) the grade for the storage vessels shall be elevated slightly above the surrounding terrain in order to ensure complete drainage of water from beneath the bottom of the vessels ; and (s) every container, vessel or tank used for storing highly flammable liquid or flammable liquefied or compressed gas shall be clearly and in bold letters marked " Danger - Highly Flammable Liquid" or" Danger - Flammable liquefied or Compressed Gas ", as the case may be. THE TAMIL NADU FACTORIES RULES, 1950 [R.95 R.95] THE TAMIL NADU FACTORIES RULES, 1950 5. Design of storage vessels. - (1) General. - Each static vessel for the storage of flammable liquefied or compressed gas shall be provided with the following fittings and instruments which are suitable/or use at pressures not less than the design pressure of the vessel and for the temperatures appropriate to the worst operating conditions namely : - (a) at least two pressure safety valves connected indepen- dently to the vapour space ; (b) two independent liquid level indicators ; ( c) a high level switch with alarm ; (d) a pressure gauge, connected to the vapour space ; and (e) a temperature gauge for measuring the temperature of the contents of the vessel. (2) Vessel connections. - In every flammable liquefied or compressed gas storage vessel - (i) all the connections to the vessel shall be designed and fitted in accordance with the Design Code of Indian Standard-2825 or equivalent duly approved by the Chief Controller of Explosives; (ii) not more than one nozzle shall be provided at its bottom for inlet and outlet purpose, apart from the drainage pipe ; (iii) the nozzle shall be a full-welded pipe and shall extend to a minimum distance of3 (three) metres from the shadow of the vessel. A combination of manual and remote operated shut-down valve shall be provided on this bottom nozzle at a distance of atleast 3 (three) metre beyond the shadow of the vessel. The nozzle shall have a slope of 1.5 degree; (iv) the nozzle shall be stress-relieved along with the vessel; (iv) (sic) there shall not be any flange, instrument tapping or manhole fitted on this nozzle upto the combination of manual and remote operated valve ; and (v) an excess flow valve shall be provided for the nozzle on the body of the vessel. THE TAMIL NADU FACTORIES RULES, 1950 [R.95 (3) Pressure Safety Valve. - In every storage vessel- (i) the pressure safety valves provided shall be of spring­ loaded type (weight-loaded safety valves shall not be used). Each of the pressure safety valves shall have 100% (hundred percent.) relieving capacity; (ii) the pressure safety valves shall be set to discharge at a pressure not more than 1 1 0 (one hundred and ten) per cent. of the design pressure of the vessel and shall have a total relieving capacity adequate for limiting the pressure build-up in the vessel not more than 120 (one hundred and twenty) per cent. of the design 'pressure; (iii) the discharge of the pressure safety valves shall be connected to flare system, if available. In case the flare system is not available, the discharge from the pressure safety valve shall be vented vertically upwards to atmosphere at a minimum elevation of 3 metre above the top of the vessel for effective dispersion of the discharge. A loose-fitting rain cap with a non-sparking chain attached to the vent pipe shall be fitted on top of the pressure safety valve ; (iv) an isolation valve shall be provided in between each pressure safety valve and the vessel. The arrangement of such isolation valve shall be so designed as to afford full required capacity flow through atleast one of the pressure safety valves; and (v) each pressure safety valve shall be visibly marked with the "set pressure" in Kg./Sq.Cm. (gauge) at which it will discharge, with its • actual rate of discharge in cubic metre per minute of the gas at a pressure of 120 (one hundred and twenty) per cent. of the design pressure of the vessel. ( 4) Emergency shut-off valve. - In every storage vessel - (i) all liquid and vapour connections, except those for pressure safety valves and the drainage connections of diameter less than 25 (twenty five) mm., shall have an emergency shut-off valve, such as an excess flow check valve or a remote operated valve : Provided that the emergency shut-off valve is not required in cases where the connection to a vessel is not greater than three centimetre in diameter for liquid and eight centimetre in diameter for vapour ; (ii) where the emergency shut-off valve provided is of' excess flow check valve ' type, its closing rate of flow shall be below the rate which is like!" to result due to a fracture of the line which it is protecting, calculated under the worst conditions. Excess flow check valve shall have a flow capacity sufficiently above the normal flow requirements to prevent valve chatter. (5) Bottom water draw-off or drain valve. - In every storage vessel,- (i) there shall be provided two drain valves at the bottom of the vessel between the remote operated valve and the first isolation valve. The length of the pipeline between the two drain valves shall be atleast 0.5 metre to minimise the risk of simultaneous obstruction of both valves due to freezing of any water present in the liquefied gas. The drain connections shall be not more than 50 (fifty) millimetre in diameter; (ii) the first drain valve from the vessel shall be of gate type (throttle type), while the second drain valve shall be of quick shut-off type ; (iii) the material of construction for the drain pipeline and the related connections shall be suitable for cryogenic application. (6) Sampling valve. - In every storage vessel, two valves with suitable distance-pipe of not less than 0.5 metre in length between them shall be fitted at its bottom between the remote operated valve and the first isolation valve for sampling purpose. (The provision of a distance-pipe is for the purpose of avoiding icing problem in the upstream valve). (7) Liquid level gauging device. - In every storage vessel, out of two level indicators provided, one shall be of " float " type and the other shall be of " differential pressure " type in case of Horton Spheres. Magnetic .. float type gauge shall be used for bullets in the place of'" differential pressure " type. " High Level " alarm shall be set on the level indicators to operate at not more than 85% (eighty five percent.) of the volumetric capacity of the vessel. An audio-visual indication as regards the high level alarm shall be provided at the normal place of operator's seat. (8) Pressure gauge. - In every storage vessel, there shall be provided atleast one pressure gauge, duly calibrated and having a dial range R.95] THE TAMIL NADU FACTORIES RULES, 1950 526 THE TAMlL NADU FACTORIES RULES, 1950 [R35 not less than 1.5 times the design pressure, easily visible and‘ designed to show the correct internal pressure at all times. It shall be provided in the vapour space at the top A suitable stop valve shall be provided in between the vessel and the pressure gauge. (9) Gas sensors. 7 In every storage vessel for flammable liquefied or compressed gas, gas sensors with alarm shall be provided at vulnerable areas and in the event of gs leakage, Such sensor shall trip ihe compressor or pump if in operation. (10) Bonding, — Electrical continuity shall be mainmined between the flanges by means of bonding in every storage vessel and its pipe lines. (1]) Pop off valves. — " Pop off” valves shall be provided in between isolation valves on the pipelines carrying flammable liquefied or compressed gases. (12) Capacity of vapor-riser. — The vapourizer, connecred ‘ to the flammable liquefied gas storage vessels shall have adequate capacity to meet the required flow rate of flammable liquefied gas in the process. 6. Prevention of ignition. i In every location where highly flammable liquid or flammable liquefied or compressed gas is stored, conveyed, handled or used or where there is danger of fire or explosion from accumulation of highly flammable liquid or liquefied compressed gas in air, all practicable measures shall be taken to exclude the sources of ignition. Such precautions shall include the following : — (a) all electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition ; (b) effective measures shall be adopted for prevention of astumulalion of static charges to a dangerous extent ; (c) no person shall wear or be allowed to wear any footwear having iron or steel nails or any other erqzosed ferrous materials which IS likely to cause sparks by friction ; (d) smolting, lighting or carrying of matches, lighters or , smoking materials shall be prohibited ; R.95] THE TAMIL NADU FACTORIES RULES, 1950 and (e) transmission bolts with iron fasteners shall not be used ; (f) all other precautions, as are reasonably practicable, shall be taken to prevent initiation of ignition from all other possible sources such as open flames frictional sparks, overheated surfaces of machinery or plant, chemical or physical-chemical reaction and radiant heat. 7. Enclosed system for conveying lziglzly flammable liquids. - Wherever it is reasonably practicable, highly flammable liquids shall be conveyed within a factory in totally enclosed system consisting of pipe lines, pumps and similar appliances from 'the storage tank or vessel to the point of use. Such enclosed system shall be so designed, installed, operated and maintained as to avoid leakage or the risk of spilling. 8. Prohibition of smoking. - No person shall smoke in any place where a highly flammable liquid or flammable liquefied or compressed gas is present in circumstances that smoking would give rise to a risk of fire. The occupier shall take all practicable measures to ensure compliance with this requirement including display of a bola notice indicating prohibition of smoking at every place where this requirement applies. 9. Fire protection. - In every factory, - ( 1 ) no vehicular traffic shall be permitted within the risk area of lower flammable limit of the highly flammable liquid or flammable liquefied or compressed gas stored. When required, vehicles filled with approved spark arrestors shall only be allowed with va!id vehicle entry permit. (2) all the vessels used for bulk storage or handling of highly flammable liquid or flammable liquefied or compressed gases shall be protected against the hazards of fire as follows : - (a) medium velocity water spray system shall be provided for all above ground storage vessels, cylinder storage or filling or repair sheds, pump houses, bulk lorry and tank wagon gantries ; (b) detection of fire for automatic actuation of medium velocity water sprinkler system shall be provided at all critical locations, such as bulk storage, tank truck or tank wagon gantry, pump or compressor house and vapourisers ; 528 THE TAMIL NADU FACTORIES RULES, l950 [K95 (c) medium velocity water sprinkler system shall be based on heat and other detection. (d) Quartzoid Bulb protection designed to blow at 79 (seventy nine) degree centrigrade (maximum) shall he provided in open areas or. in the sheds ; (e) medium velocity water sprinkler system shall function in such a way that the actuation of fire detectors shall initiate the following : i (i) opening ofdeluge valve ; (ii) audio-visual alarm at the fire pump house or control panel ; (iii) fire siren ; and (iv) the diesel pump will get started based an the “ Set pressure ” to supplement or to maintain the fire water pressure in the ring main ; and _ (t) the medium velocity water sprinkler system shall have a minimum spray density of ten litres per minute per square metre in the ease of flammable liquefied or compressed gas and in the case ofhighly flammable liquid it shall have minimum spray density of 3 (three) litres per minute per square metre for the single largest risk area For the purpose of calculation of a single risk area, the following shall be taken into account : i (i) in case of bulk storage, adjoining vessels within the distance of R + 30 (thirty) metre, where R is the radius of the vessel and 30 (thirty) metre shall be measured from the periphery ofthe vessel. (ii) in case of tank lorry gantry. a maximum of 8 (eight) bays shall be taken as a single risk area ; and (iii) in case of tank wagon gantry, a minimum of one gantry (600 (six hundred) Metric Tomes) shall be taken as asingle risk area (3) (a) a fire water ring main shall he provided all around the locations of storage and handling of flammable liquefied or compressed ‘gases with hydrants or monitors spaced at 30 (thirty) metre centre to centre. Fire hydrants and monitors shall be installed outside the licensed premises : (b) the fire water pressure system' shall be designed for a minimum residual pressure of 7 (seven) Kgf/Sq. Cm. (gauge) at the remotest place of application in the plant ; ( c) fire hydrant network shall be provided in closed loops to ensure multi-directional flow in the system. Isolation valves shall be provided to enable isolation of any section of the network without affecting the flow in the rest ; and (d) the fire water system in the plant shall be designed to meet the highest fire-water flow requirement of medium velocity water sprinkler for a single largest risk area at a time plus 288 (two hundred and eighty eight) metre/hour for operating 2 (two) numbers fire water monitor or supplementary hose requirements. (4) (a) water for the hydrant service shall be stored in any easily accessible surface of underground concrete reservoir or above ground tank of steel or concrete ; / (b) the effective fire water storage capacity available for fire­ fighting shall be for four hours ; and ( c) storage tank or reservoir for fire water shall be in two interconnected compartments to facilitate cleaning and repair, _ (5) Portable fire extinguishers as approv.ed by Bureau oflndian Standards shall be located at convenient places as indicated in the Table below :- THE TABLE AREA (1) 1. Flammable liquefied gas or storage vessels ( each) 2. Tank wagon loading or unloading gantries 3. Tank truck loading or unloading gantries. PORTABLE FIRE EXTINGUISHER (2) 2 Numbers 10 Kg. DCP. 1 Number 10 Kg. DCP. extinguisher for every 15/20 metres of gantry I Number IO Kg. DCP. fire extin­ guisher in each Bay and 1 Number 50 Kg. Mobile DCP unit/gantry R.95] THE TAMIL NADU FACTORIES RULES, 1950 The dry chemical powder used in the extinguishers shall be potassium or Urea based or Sodium Bicarbonate as per IS : 4308. The expellent gas i.e., N 2 I C0 2, should be of good quality. 10. Loading and unloading facilities for flammable liquefied or compressed gas. -(1) !Loading. - In every factory, where the loading of flammable liquefied or compressed gas is carried on, the loading station shall consist of the following: - (a) a filling line with an isolation valve and check valve ; (b) a vapour return line with a check valve and an isolation valve to be connected back to the storage vessel from which the loading pump is drawing flammable liquefied gas ; ( c) suitable loading arm or flexible hoses shall be provided at the end of filling line and vapour return line for connecting to the I tank truck vessels or tank wagons ; and _ (d) suitable thermal pressure reliefvalve(s) shall be provided between the shut-off valves to protect against excessive pressure which may develop due to thermal expansion of the trapped liquid . (2) Unloading. - In every factory, where unloading of flammable liquefied or compressed gas is carried oil, the compressor used for unloading of flammable liquefied gases by means of a differential pressure between the receiving and discharging vessels by withdrawing vapour from the receiving vessel and forcing it at high pressure into the discharging vessel shall have the following facilities : - (a) liquid unloading check valve line with isolation valve; and (b) vapour line with isolation valves ; (3) Loading and unloading operations. - In every factory, where the loading or unloading of flammable liquefied or compressed gas is carried on, - (a) written operating procedures for loading or unloading operation, clearly defining the safety checks and precautions to be observed as well as the responsibilities of the personnel involved in such operation, shall be prepared both in English and in Tamil and shall be given to them and also displayed at the site ; (b) flexible hoses used for transfer of flammable liquefied •.1r compressed gas to or from a tank truck or tank wagon shall be, - THE TAMIL NADU FACTORIES RULES, 1950 [R.95 R.95] THE TAMIL NADU FACTORIES RULES, 1950 (i) designed and constructed in accordance with the Static and Mobile Pressure Vessels (Unfired) Rules, 1981 ; (ii) having a means of identification ; and (iii) periodically checked for electrical and mechanical continuity and recorded in the register ; ( c) for connecting and disconnecting hoses, only non­ sparking type of tools shall be used ; (d) the tank truck shall have the starter motor which shall be of non-sparking or flame-proof type; ( e) the tank truck shall be positioned on a levelled ground and blocks (checks) shall be placed at front and rear wheels in order to prevent thp risk of accidental vehicle movement ; (f) the engine of the vehicle shall be stopped and all the electrical equipment shall be switched off, before commencing the loading or unloading operation ; (g) before commencing the loading or unloading operation, static charge shall be effectively discharged by bonding and earthing of the storage vessels and the road tankers or wagons ; (h) the road tanker or wagon shall be electrically bonded at, specified point to the fixed grounding system ; (i) an authorised person shall supervise the transfer operation and respond immediately in the event of an emergency ; G) during loading operation, the pressure within the receiving tank truck vessel shall be observed to ensure that it does not approach the " start-to-discharge " pressure of the relief valve. Filling rate shall be regulated as required ; (k) the receiving vessel which is having an internal pressure of less than l(one) Kg./Sq.Cm. (g) shall not be permitted to be filled, such vessel shall be checked for Oxygen content or explosive mixture and purged, if necessary ; (l) filling or transfer operation shall be done only during day time; (m) filling or transfer operation shall be stopped immediately in the event of - [R.95 (a) uncontrolled leakage occurring ; (b) a fire occurring in the vicinity ; ( c) lightning and thunder-storm ; (n) the " Safe Operating Procedure " for unloading shall be displayed conspicuously in English and Tamil near the unloading area 11. Maintenance and Inspection. - In every factory where highly flammable liquid or flammable liquefied or compressed gas is stored in bulk, - ( 1) the storage vessels and the safety fittings and instruments shall be tested periodically as per the requirements under various statutes as applicable and relevant records with the particulars of such testing shall be maintained ; (2) loading or unloading hoses shall be tested atleast once in every six months ; (3) the earth pits shall be maintained well and the earth resistance shall be measured atleast once in every 12 (twelve) months; and records shall be maintained in this regard ; (4) the foundation and supports of the storage vessels shall be checked once in a year for differential settlement due to disturbance in the sub-soil ; (5) the cathodic protection, if provided, shall be monitored periodically and maintained well for its effectiveness ; (6) the gas detection system shall be checked and calibrated periodically ; and (7) the fire water system which includes fire water pumps, fire hydrant or monitor, piping network and water sprinkler or deluge system shall be checked periodically and maintained well for its fail-safe operation. 12. Training. - The occupier of every factory in which highly flammable liquid or flammable liquefied or compressed gas is stored in bulk shall ensure that - ( 1) the supervisory or managerial personnel are adequately trained in ail aspects of safe storage and handling of highly flammable THE TAMIL NADU FACTORIES RULES, 1950 R.95] THE TAMIL NADU FACTORIES RULES, 1950 liquid or flammable liquefied or compressed gas as well as disaster control or preparedness and response. (2) regular raining programmes are conducted in loading or unloading operation, draining procedure, commissioning and decommissioning procedures," hot work" permit system, fire-fighting or emergency combat operation, health hazards etc., for- (a) regular workers; (b) contract workers ; and ( c) security staff. (3) full-scale emergency mock drill, simulating leakage of flammable gas and the consequent major fire, are conducted in the plant atleast once in every six months in order to assess the level of preparedness and the adequacy of combat measures. Any deviations or defects observed during such mock-drill shall be rectified forthwith. 13. Exemption. - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this Schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion, revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein.) [R.95 1 (Schedule XXXII OPERATIONS IN FOUNDARIES AND FURNACES J. Application. - Provisions of this Schedule shall apply to all parts of factories where any of the following operations or processes are carried on : - (a) the production of iron castings or, as the case may be, steel castings by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by shell moulding or by centrifugal casting and any process incidental to such production ; (b) the production of non-ferrous castings by casting metal in moulds made of sand, loam, metal, moulding composition or other material or mixture of materials, or by shell mouldings, die-casting (including pressure die-casting), centrifugal casting or continuous casting and any process incidental to such production ; ( c) the melting and castmg of non-ferrous metal and I or ferrous metal for the production of ingots, billets, slabs or other similar products and the stripping thereof; but shall not apply with respect to - (i) any process with respect to the smelting and manufacture of lead and the Electric Accumulators ; (ii) any process for the purposes of printing works; (iii) any smelting process in which metal is obtained by a reducing operation, or any process incidental to such operation ; or (iv) the production of steel in the form of ingots; or (v) any process in the course of the manufacture of solder or any process mcidental to such manufacture ; or (vi) the melting and casting of lead or any lead-based alloy for the production of ingots, billets, slabs or other similar products or the stripping thereof any process incidental to such melting, casting or stripping. I Originally inserted by GO. Ms. No. 1852, Labour and Employment, dated the 31 s August, 1988 and subsequently substituted by G.0. Ms. No. 255, Labour an, Employment (M2), dated the 25th October 2013. THE TAMIL NADU FACTORIES RULES, 1950 R.95] THE TAMIL NADU FACTORIES RULES, 1950 2. Definitions. - For the purpose of this Schedule, - (a) " approved respirator " means a respirator of a type approved by the Chief inspector ; (b) " cupola or furnace " includes a receiver associated therewith; ( c) " dressing or fettling operations " includes stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting, and the production of reasonably clean and smooth surface, but does not include, - (i) the removal of metal from a casting when performed incidentally m connection with the machining or assembling of castmgs after they have been dressed or fettled; or (ii) any operation which is knock-out operation within the meaning of this Schedule; ( d) " foundry " means those parts of a factory in which the production of iron or Steel or non-ferrous castmgs (not being the production of pig iron or the production of steel in the form of ingots) is carried on by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by steel moulding or by centrifugal castmg in metal moulds lined with sand or die-casting including pressure die-casting together with any part of the factory in which any of the following processes are carried on as incidental processes in connection with and in the course of such production, namely, the preparation of moulds and cores, knock out operations and dressing or fettling operations ; ( e) " knock-out operations " means all methods ofremoving casting from moulds and the following operations, when done in connection therewith, namely, strippmg, cormg-out and the removal of runners and risers ; (t) " pourmg aisle " means an aisle leadmg from a main gangway or directly from a cupola or furnace to where metal is poured into moulds ; (g) " qualified supervisors " means a person possessmg a Bachelor's Degree in Science or Diploma or Degree in Engineenng with Certificate in ferrous/non-ferrous technology from any institution recognised by the Chief Inspector. 3. Prohibition of use of certain materials as parting materials : - (I) A material shall not be used as a parting material if it is a material containing compounds of sihcon calculated as silica to the extent more than 5 percent by weight of the dry material : Provided that this prohibition shall not prevent the following being used as a parting material, if the material does not contain an admixture of any other silica - (a) Zirconium silicate (zircon). (b) Calcines - China Clay. (c) Calcine Aluminous fireclay (d) Sillimanite (e) Calcined or fused Alumina (f) Olivine (g) Natural sand. (2) Dust or other matter deposited from a fettling or blasting process shall not be used as a parting material or as a constituent m a parting material. 4. Arrangement and Storage. - For the purposes of promoting safety and cleanliness m workrooms, the following requirements shall be observed:- (a) mouldmg boxes, loam plates, ladles, patterns, pattern plates, frames, boards, box weights and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; (b} suitable and conveniently accessible racks, bms, or other receptacles shall be provided and used for the storage of other gear and tools ; ( c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. THE TAMIL NADU FACTORIES RULES, 1950 [R.95 R35] THE TAMIL NADU FAC'lORlES RULES, 1950 53 7 5. Construction. Installation and Operation. —(l) The precinct in which induction furnace is installed shall be of adequate strength and shall be segregated from the other parts of the factory in such a way so that minimum number of workers is exposed in the risk of any fire or explosion at any time ; (2) Furnace shed shall be well ventilared ; (3) All the fittings and attachment oflnduccion furnace shall be of good construction, sound material and adequate strength ; (4) Adequate arrangements shall he made to avoid tilting of the ladles while transportation ; (S) Ladle shall not be filled WILh molten metal more than 3/41h ofits volume to avoid spillage of molten metal while being carried by the crane ; (6) The refractory material of the induction furnace shall be strong at high temperature, resistant to thermal shock, chemically inert. low thermal eanductivny and coefficient of expansion and of adequate uniform thickness ; (7) The lining of Lhe inductlon furnace shall be checked by qualified supervisor every week for any wear and tear and damage as per relevant Bureau of lndian Standards ; (l3) Adequate precautions shall be taken during repair of induction time: as per relevant Bureau of Indian Standards. 6. Construction of floors. — (1) Floors of indoor workplaces in which the processes are carried an, other than parts which are of sand, shall have been surface ofhard mam-la] ; (2) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done ; (3) All parts of the surface of the floor of any such indoor workplace which are of sand shall, so far as practicablefi be maintained in an even and firm condition 7. Means ofeseape. A There shall be atleast two ways of escape with adequate width at opposite ends of the filmace platforms. ‘8. DisplayofNotice 7 Notice regarding non-use of water; etc. near induction furnace shall be displayed THE TAMIL NADU FACTORIES RULES, 1950 [R.95 9. Charging of scrap in Induction Furnace. - (1) No scrap material with close cavities shall be charged in the induction furnace. Scrap to be charged shall be dry and shall not contain oil or any other liquid or moisture. (2) No scrap material shall be fed into induction furnace unless it is thoroughly checked in the presence of qualified Supervisor. (3) No closed container scrap shall be fed into the furnace unless it is cut into pieces. Such container shall be rendered safe by suitable means. (4) No wet scrap material shall be charged into the induction furnace. (5) Scrap received m the form of pressed bundle should be opened, sorted and only then fed mto furnace. 10. Cleanliness of indoor workplaces. - (1) All accessible parts of the walls of every mdoor workplace in which the processes are carried on and of everythmg affixed to those wall shall be effectively cleaned by a suitable method to a height of not less than 4.2 metres from the floor atleast once in every period of fourteen months. A record of the carrymg out of every such effective cleaning in pursuance of this paragraph includmg the date (which shall neither be less than five months nor more than nine months after the last immediately preceding washmg, cleanmg or other treatment). (2) Effective cleaning by a suitable method shall be carried out atleast once every working day of all accessible parts of the floor of every indoor workplace m which the processes are carried on, other than parts which are of sand ; and the parts which are of sand shall be kept in good order. 11. Manual operations involving molten metal. - ( 1 ) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation - (a) which is adequate for the performance of the work ; and (b) which, so far as reasonably practicable, is kept free from obstruction. (2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which where any person walks while engaged in the operation shall be on the same level: Provided that where necessary to enable the operation to be performed without undue nsk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 12. Gangways and pouring aisles. - (1) In every workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this schedule, and so far as reasonably practicable, in every other workroom to which this paragraph applies, sufficient and clearly defined mam gangway shall be provided and properly maintamed which - (a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage ; (b) shall be kept, so far as reasonably practicable, free from obstruction ; ( c) if not used for carrymg molten metal ; shall be atleast 920 millimetres m width ; ( d) ifused for carrying molten metal shall be - (i) where truck ladles are used exclusively, atleast 600 milhmetres wider than the overall width of the ladle; (ii) where hand shanks are carried by not more than two men, atleast 920 millimetres in width ; (iii) where hand shanks are carried by more than two men, atleast 1.2 metres in width ; (iv) where used for simultaneous travel in both directions by men carrying hand shanks, atleast 1.8 metres in width ; (2) In workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this R.95] THE TAMIL NADU FACTORIES RULES, 1950 [R.95 (a) shall have an even surface of hard material and shall in particular, not be sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage ; (b) shall be kept so far as reasonably practicable free from obstruction ; ( c) if molten metal is carried in hand ladles or bulk ladles by not more than two men per ladle, shall be atleast 460 millimetres wide, but where any moulds alongside the aisle are more than 5 1 0 millimetres above the floor of the aisle, the aisle shall be not less than 600 millimetres wide; ( d) if molten metal is carried in hand ladles or bull ladles by more than two men per ladle, shall be atleast 760 millimetres w i d e ; ( e) if molten metal is carried in crane, trolley or truck ladles, shall be of a width adequate for the safe performance of the work. (3) Requirements of sub-paragraphs ( 1 ) and (2) shall not apply to any workroom or part of a workroom if, by reason of the nature of the work done therein, the floor of the workroom or, as the case may be, that part of a workroom has to be of sand. ( 4) In this paragraph " workroom to which this paragraph applies" means a part of a ferrous or non-ferrous foundry in which molten metal is transported or used and a workroom to which this paragraph applies shall be deemed for the purposes of this paragraph to have been constructed, reconstructed or converted for use as such after the making of this Schedule if the construction, reconstruction or conversion thereof was begun after the making of this Schedule. 13. Work near cupolas and furnaces. - No perspn shall carry out any work within a distance of 4 metres from a vertical line passing through the delivery end of any spout of a cupola or furnace, being a spout used for delivering molten metal, or within a distance of 2.4 metres from a vertical line. passing through the nearest part of any ladle which is in position at the end of such a spout, except in either case, where it is necessary for the proper use or maintenance of a cupola or furnace that work should be carried out within that distance of that work is being carried out at such a time and under such conditions that there is no danger to the person , THE TAMIL NADU FACTORIES RULES, 1 9 5 0 Schedule, sufficient and clearly defined pouring aisles shall be provided and properly maintained which - R.95] carrying it out from molten metal which is being obtained from the cupola or furnace or is in a ladle in position at the end of the spout. 14. Dust and fumes. - ( 1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. (2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. (3) Mould stoves, core stoves and annealing furnaces shall be so designed, constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. ( 4) All knock-out operations shall be carried out - (a) in a separate part of foundry suitably partitioned off, being a room or part in which, so far as reasonably practicable, effective and suitable local exhaust ventilation and� high standard or general ventilation are provided ; or \ (b) in an area of the foundry m which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. (5) All dressing or fettling operation shall be carried out- (a) in a separate room or in a separate part of foundry suitably partitioned off; or (b) m an area of the foundry set apart for the purpose ; and shall so far as reasonably practicable, be carried out-with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 15. Maintenance and examination of exhaust plant. - ( I ) All ventilation plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be properly maintained. THE TAMIL NADU FACTORIES RULES, 1950 (2) All ventilation plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person at least once in every period of twelve months ; and particulars of the results of every such examination and test shall be entered in an approved register which shall be available for inspection by an Inspector. Any defect found on any such examination and test shall be immediately reported in writing by the person carrying out the examination and test to the occupier or manager of the factory. 16. Protective equipment. - (1) The occupier shall provide and maintain protective equipment specified for the protection of workers, - (a) suitable gloves or other protection for the hands for workers engaged in handling any hot material likely to cause damage to the hands by bum, scald, or scar, or in handling pig iron, rough castings or other articles likely to cause damage to the hands by cut or abrasion ; (b) approved respirators for workers carrying out any operations creating a heavy dust concentration which cannot be dispelled quickly and effectively by the existing ventilation arrangements. (2) No respirator provided for the purpose of clause (b) of sub­ paragraph ( 1) has been worn by a person shall be worn by another person if it has not since, been thoroughly cleaned and disinfected. (3) Persons who for any of their time - (a) work at a spout of or attend to, a cupola or furnace in such circumstances that material there from may come into contact with the body, being material at such a temperature that its contact with the body would cause a born ; or (b) are engaged in, or in assisting with, the pouring of molten metal; or ( c) carry by hand or move by manual power any ladle or mould containing molten metal ; (d) are engaged in knocking-out operations involving material at such a temperature that its contact with the body would cause a bum ; shall be provided with suitable footwear and gaiters which worn by them prevent, so far as reasonably practicable, risk of bums to his feet and ankles. THE TAMIL NADU FACTORIES RULES, 1950 [R.95 (4) Where appropriate, suitable screens shall be provided for protection against flying materials (including splashes of molten metal and sparks and chips thrown off in the course of any process). (5) The Occupier shall provide and maintain suitable accommodation for the storage and make adequate arrangements for cleaning and maintaining of the protective equipment supplied in pursuance of this paragraph. ( 6) Every person shall make full and proper use of the equipment provided for his protection in pursuance of sub-paragraphs ( 1) and ( 4) and shall without delay report to the occupier, manager or other appropriate person any defect in, or loss of, the same. (7) Workers working in the furnace/casting pit area shall be provided with cotton clothes, safety shoes, leg guards; apron, face shield, hand gloves and safely helmet. (8) Workers employed for segregation of scrap shall be provided with safety shoes and hand gloves. (9) Fire retardant and heat retardant clothing shall be provided to all the workers working on platform ofinduction furnace. 17. Training and Supervlslon, - ( I) All operations under this Schedule shall be carried out under the supervision of qualified supervisors at all times. (2) Workers carrying out operations and maintenance activities in foundries and furnaces shall be adequately trained. R 8. Washing and bathing facilities. - (I) There shall be provided and maintained in clean state and good repair for the use of all workers employed in the foundry, - (a) a wash place under cover with either - (i) a trough with impervious surface fitted with a waste pipe without plug and of sufficient length to allow atleast 60 centimetres for every 10 such persons employed at any one time and having a constant supply of clean water from taps or jets above the through at intervals of not more than 60 centimetres ; or (ii) atleast one tap or stand pipe for every IO such persons employed at any one time and having a constant supply R.95] THE TAMIL NADU FACTORIES RULES, 1950 5 44 Tire TAMlL NADU FACTORIES RULES, 1950 [1135 of Clean water, Lhe tap or stand pipe being spaced not less than 1.2 metres apart ; and (b) not less than one half of the total number of washing places provided under clause (a) shall be in form of bathrooms ; (c) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. (2) The facilities provided for the purposes of sub-paragraph (1) shall be placed in charge of a responsible person or persons and maintained in a clean and orderly condition. 19. Disposal of dross and skimming. 7 Dress and skimming removed from molten metal or taken from a fumace shall be placed forthwith in suitable receptacles. 20. Disposal of Waste 7 Apprnrtriate measures shall be taken for the disposal all waste products from shell moulding (including waste burnt sand) as soon as reasonably practicable after the castings have been knocked-out. 21. Material and Equipment lelt out ot doors. 7A“ material and equipment left out of doors (including material and equipment so lefi only temporarily or occasionally) shall be so arranged and placed as to avoid unnecessary nsk. There shall be safe means of access to all such material and equipment and so far as refinnably practicable, such access shall be by roadways or pathways which shall be properly maintained. Such roadways or pathways shall have a firm and even surface and shall so far as reasonably practicable be kept free from obstruction 22. Medical facilities and records of examinations and tests. — (1) The Occupier of every factory to which this Schedule applies, shall — (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval ofthe Chieflnspector ofFactorles ; and (b) Provide to the medical practitioner all the necessary facilities for the purpose referred to in clause (a), (2) The record of such examinations carried out by the medical practitioner shall be maintained. in a separate register approved by the Chief R.95) THE TAMIL NADU FACTORIES RULES, 1950 Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 23. Medical examination by Certifying Surgeon. - (1) Every worker employed in the process specified in paragraph I shall be examined by a Certifying Surgeon within fifteen days of his first employment. Such examinations shall include skin test for dermatitis, Pulmonary function test and Chest X-ray and no worker shall be allowed to work after fifteen days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the processes specified in paragraph l shall be re-examined by a Certifying Surgeon at least once in every three calendar months and such examination shall, wherever the Certifying Surgeon considers appropriate include all the tests in sub­ paragraph (I) except chest x-ray which will be once in three years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of fitness in Form No. 27. The record of examination and re examinations carried out shall be entered in the Certificate and the Certificate sha11 be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs ( I) and (2) including the nature and the results of these tests, shall also be entered by the Certifying Surgeon in Health Register in Form No. I 7. ( 4) The Certificate of fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the Health Register. the entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said process. Such person shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub­ paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon. after further examination again certifies him fit for employment in those processes. [R.95 (7) Workers working in the furnace and casting pit area shall be medically examined by qualified Medical Practitioner once in a year. 24. Exemptions. - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this Schedule is not necessary for the protection of the workers in the factory, I the Chief Inspector may, by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein ) THE TAMIL NADU FACTORIES RULES, 1950 R.96] THE TAMIL NADU FACTORIES RULES, 1950 96. Notification of accidents. - (1) When any accident or dangerous occurrence specified in the Schedule occurs in a factory the manager of the factory shall forthwith send notice thereof by telephone, special messenger or telegram to the Inspector and the chief Inspector: Provided that in respect of any accident or dangerous occurrence specified in sub-item (a) of item l and 2 of the Schedule, notice as aforesaid shall also be sent to : - (a) The District Magistrate or Sub-Divisional Officer; and (b) The Officer-in-charge of the Police Station having jurisdiction over the area : Provided further that in respect of any accident specified in item 1 of the Schedule, notice as aforesaid shall also be sent to the next of kin of the injured or deceased person. (2) The notice so given under sub-rule (1) in respect of an accident shall be confirmed by the manager of the factory by sending to the above-mentioned authorities within 12 hours of the accident, a separate written report in respect of each person killed or injured in the prescribed Form No. 18 . (3) The notice so given under sub-rule ( l ) in respect of a dangerous occurrence specified in paragraph 2 of the Schedule shall be confirmed by the manager of the factory by sending to the above­ mentioned authorities within 12 hours of the dangerous occurrence a written report in the prescribed 1[Form No. 18-AJ. ( 4) When any accident occurs in a factory which causes suer. bodily injury as prevents the person injured from working for a period of 48 hours immediately following the accident, the Manager of the factory shall send to the Inspector, within 24 hours of the expiry of 48 hours after the occurrence of the accident, a separate report thereof in respect of each person injured, in the prescribed Form No. 18 : Provided that it shall be open to the Chief Inspector of Factories to accept a report in any ·other form if he is satisfied that the form contains all the particulars specified in Form No. 18 aforesaid. I Sub. for" Form 18 ", by G.0. Ms. No. 121 , Labour and Employment (M-2), dated the 31st July, 2012. (5) Wherever the person injured returns to work in the factory without any disablement before the expiry of 21 days after the occurrence of the accident, the Manager of the factory shall send to the Inspector within 7 days of the return to work of the person injured a written report giving the particulars of - (a) the Registration Number of the factory; (b) the relevant serial running number of the accident in the factory for the calendar year and calendar year as reported against item 2 in the report in Form No. 18 ; (c) the name of the person injured; ( d) the date ofaccident ; ( e) the date of return to work ; and (f) the number of days the person injured was away from work. Such reports may also be sent in convenient batches for a number of accidents together at a time within the time prescribed. (6) Wherever the person injured does not return to work in the factory before the expiry of 21 days after the occurrence of the accident with or without disablement and wherever the person mjured returns to work in the factory after sustaining compensable disablement as a result of the accident, the Manager of the factory shall send to the Inspector within 28 days of the occurrence of the accident, a written report in the prescribed Form No. 18-B and follow it up as necessary with further reports in the same Form No. 18-B once every fortnight thereafter, until the final report on the date of return to work of the person injured is made. In the event of the person injured not returning to work of his own accord or otherwise the full circumstances of the same should also be reported to the Inspector by the Manager of the factory within seven days of his name being removed from muster roll of the factory. Even if the person injured were to be covered by the Employees' State Insurance Scheme it shall be the responsibility of the Manager of the factory to obtain the relevant information for the purpose of this rule and Form No. 18-B and report the same to the Inspector as prescribed. THE TAMIL NADU FACTORIES RULES, 1950 [R.96 R.97] TAMILNADU FACTORIES RULES, 1950 TilllE SCHEIDUJLJE 1. (a) An accident which causes death to any person or is of such a serious nature that it is likely to prove fatal. (b) An accident of a serious nature which is likely to result in loss of limbs or vision or permanent disablement to any person. 2. The following classes of dangerous occurrence whether or not they are attended by personal injury or disablement : -- (a) Bursting of a plant used for containing or supplying steam under pressure greater than atmospheric pressure. (b) Collapses or failure of a crane, derrick, winch, hoist or other appliance used in raising or lowering persons or goods, or any part thereof, or the overturning of a crane. (c) Explosion or fire or bursting out, leakage or escape of any hot (molten) metal, liquid or gas causing damage to any person or any room or place in which persons are employed, or fire in rooms of cotton pressing factories when a cotton opener is in use. (d) Explosion of a receiver or container used for the storage at a pressure greater than atmospheric pressure of any gas or gases (including air) or any liquid or solid resulting from the compression of gas. (e) collapse or subsidence of any floor, gallery, roof, bridge, tunnel, chimney, wall, building or any other structure. (f) Bursting of centrifugal machines. 97. Notice of poisoning or disease. --A notice in Form No. 19 should be sent forthwith both to the Chief Inspector and to the Certifying R l Surgeon, by the Manager of a factory in which there occurs a uie prescn- fl d h h · b b d d case o ea , p osp orus, mercury, manganese, arsemc, car - e r un 8 ;r on bisulphide or benzene poisoning ; or poisoning by nitrous sec ion fumes; or by halogen or halogen derivatives of the hydrocar­ bons of the aliphatic series or of chrome ulceration, anthrax, silicosis, toxic anaemia, toxic jaundice, primary opithelomatous cancer of the skin, or pathological manifestations due to radium or other radio-active substan- ces or X-rays. · ' TAMIL NADU FACTORIF.S RUI.ES, 1950 CHAPTERX Supplemental [R.98 98. Pirocedure in appeals. -- (1) 1[An appeal presented under section 107 shall lie to the Chief Inspector, or in cases where the order appealed against is an order passed by the Chieflnspector, to the State Government Rule prescri- and shall be in the form of memorandum setting forth con­ bed under cisely the grounds of objection to the order and bearing court section 107. fee stamp in accordance with Article 11 of Schedule II to the Court-fees Act, 1870, and shall be accompanied by a copy of 14'? order appealed against certified correct and attested by the Inspector concerned and duly stamped under the same Act.] NOTE. --According to the positionon 1st January, 1949, the scale of court-fee stamp to be affixed to an appeal is Rs. 2 and in respect of certified copy of the order, eight annas for every 360 words or part thereof. (2) Appointment or assessors. -- On receipt of the memorandum of appeal, the appellate authority shall, if it thinks fit or if the appellant has requested that the appeal should be heard with the aid of assessors, call upon the body declared under sub-rule (3) to be representative of the industry concerned, to appoint an assessor within a period of 14 days. If an assessor is nominated by such body, the appellate authority shall appoint a second assessor itself. It shall then fix a date for the hearing of the appeal and shall give due notice of such date to the appellant and to the Inspector whose order is appealed against, and shall call upon the two assessors to appear upon such date to assist in the hearing of the appeal. (3) The appellant shall state in the memorandum presented under sub-rule (1) whether he is a member of one or more of the following bodies. The body empowered to appoint the assessor shall -- (a) if toe appellant is a member of one of such bodies, be that body; Subs. by G.O. Ms. No.1479, Labour, 6th July, 1988. R. 98] TAMILNADU FACTORIES RULES, 1950 (b) if he is a member of two such bodies, be the body which the appellant desires should appoint such assessor ; and ( c) if the appellant is not a member of any of the aforesaid bodies or if he does not state in the memorandum which of such bodies he desires should appoint the assessor, be the body which the appellate authority considers as the best fitted to represent the industry concerned: (1) Employers' Federation of Southern India. (2) Tamil Nadu State Board of the All-India Manufacturers' Organi- sation. (3) Tamil Nadu Small Scale Industries Association. (4) The South India Mill Owners' Association. (5) (6) (7) (8) 1[ (9) (10) ( 1 1 ) The Planters' Association of Tamil Nadu. ( 12) The South India Textile Research Association. ( 13) (14) (15) (16) (17) (18) (19) (20) (21) The Hindustan Chamber of Commerce. (22) The Madras Chamber of Commerce. (23) The Coimbatore Chamber of Commerce. (24) The Madura-Ramnad Chamber of Commerce. (25) The Tuticorin Chamber of Commerce. (26) Andhra Chamber of Commerce, Madras- I. 2[(27) Tamil Nadu Spinning Mills Association, Dindigul.] I Subs. by GO. Ms. No 81, Labour and Employment (M-2), dated 19-02-2013. 2 Added by GO. Ms. No 119, Labour and Employment (M-2), dated 9-8-2005. Tamil Nadu Mill Owners' Association. The South India Sugar Mills Association. The South India Tanners' and Dealers' Association. The Southern India Skin and Hide Merchants Association. Confederation of Indian Industry.] The United Planters' Association of Southern India. Cement Service Bureau. Madras Productivity Council. The Coimbatore Productivity Council. Tiruchirappalli Productivity Council. Salem Productivity Council. Madurai Productivity Council. Tirunelveli Productivity Council. The Southern India Chamber of Commerce. [R.99 ( 4) Remuneratlon or assessors. -- An assessor appointed in accordance with the provisions of sub-rules (2) and (3) shall receive for the hearing of the appeal, a fee to be 'fixed by the appellate authority, subject to a maximum of fifty rupees per diem. He shall also receive the actual travelling expenses. The fees and travelling expenses shall be paid to the assessor by Government; but where assessors have been appointed at the request of the appellant and the appeal has been decided wholly or partly against him, the appellate authority may direct that the fees and travelling expenses of the assessor shall be paid in whole or in part by the appellant. 99. Display of notices. -- An abstract of the following provisions of Rule prescri- the Act and Rules shall be displayed in a conspicuous arid bed under convenient place at or near the main entrance in · every section 108. factory : iNTERPRETATRON CLAUSES (l) AND (m) of SECTION 2- lfNTERPREI'ATION Working hours, holidays, intervals for rest, etc. 1. Sections 51 and 54-Hours of work (Adults). 2. Section 52-Weekly holidays (Adults). 3. Sections 55 and 56-Intervals for rest and spread over (Adults). 4. Section 59-Extra wages for overtime. 5. Section 64- (i) Exemption of supervisory staff. /, (ii) Relaxation of hours of work (Adults). 6. Sections 60, 71 and 99-Prohibition of double employment. 7. Section-fie-Restriction on employment of women. 8. Section:67-Prohibition of employment of children under 14 years. 9. Section 71-Working hours for children. Annual leave with wages 10. Sections 79 and 80 and rules 86-A, 87 and 88-Leave with wages. TAMIL NADU FACTORIES RULES, 1950 R.99] TAMIL NADU FACTORIES RULES, 1950 Health 11. Section 11-Cleanliness. 12. Section 12-Disposal of wastes and effuents. 13. Section 13-Ventilation and temperature. 14. Section 16-0vercrowding. 15. Section 17-Lighting. 16. Section 18-Drinking water. 17. Section 19 and Rules 40 to 49-Latrines and Urinals. 18. Section 20-Spittoons. Safety 19. Section 21-Fencing of machinery. 20. Section 22-Work on or near machinery in motion 21. Section 23-Employment of young persons on dangerous machines. 22. Section 26-Casing of new machinery. 23. Section 27-Prohibition of employment of women and children near cotton-openers. 24. Section 34-Excessive weights. 25. Section 35-Protection of eyes. 26. Section 38-Precaution in case of fire. Welfare 27. Section 42-Washing facilities. 28. Section 43 and rule 62-A =Facilities for storing and drying clothes. 29. Section 44-Facilities for sitting. 30. Section 45-First-aid appliances. 31. Section 46 and rules 65 to 71-Canteens TAMIL NADU FACTORIES RULES, 1950 [R. 100-A 32. Section 47-Shelters, rest rooms and lunch rooms 33. Section 48 and rules 73 to 76 - Creches. 34. Section 49 - Welfare Officers. Special provisions 35. Section 9 and rule 13 - Powers of Inspectors. 36 Sections 61, 63, 72, 74,79 and 1 1 0 - Registers, notices and re- turns. 37 Sections 68, 69, 70 and 98 - Certificates of fitness. 38. Section 82-Mode of recovery of unpaid wages. 39. Section 87 and rule 95 - Dangerous operations. 40. Section 88 and rule 96 - Notice of certain accidents. 41. Section 89 and rule 97 - Notices of certain diseases. 42. Sections 97 and 1 1 1 - Offences by, and obligations of workers. 43. Section 1 i 4-No charge for facilities and conveniences. ( 1) A 1[(2) a combined annual return for every calendar year, in dupli­ cate, m Form No. 22 so as to reach the inspector on or before the 31st January of the following year.] 2[* * *] 2[100-A]. In the case of a factory m which work is carried on only during certain penod or penods of the year, the Manager shall, if so required by the State Government or if the State Government so directs, through the Chief Inspector, submit the annual or half-yearly returns mentioned in rule I 00 within fifteen days after the close ot that period or after the close of the last of those periods in the year as the case may be I Subs by G O Ms No 257, Labour and Employment (M-2), dated the 16th August, 2004 2 Om med by G O Ms. No 698, Labour and Employment. dated the 1 1 t h August, 1975 •1 Renumber ed tbul half-yearly return for the first half of every calendar year, in duplicate in Form No. 21 so as to reach the Inspector on or before the 3 1s t July of the year. 100. Returns. - 4 [The Manager of every factory shall furnish to the Inspector through online portal of Directorate of Industrial Safety and Health, the following returns, namely:-,] officers Typewritten text 4Ins.by G.O.Ms.No.15, Labour and Employment (M2), dated 31st January, 2018. Rule pres- IOI. Service of Notice. - The despatch by post cribed under under registered cover of any notice or order shall be section 109. deemed sufficient service on the Occupier, Owner or Manager of a factory of such notice or order. 102. Information required by the Inspector. - The Occupier, Owner or Manager of a factory shall furnish any information that an Inspector may require for the purpose of satisfying himself whether any provision of the Act has been complied with or whether any order of an Inspector has been duly carried out. Any demand by an Inspector for any such information, if made during the course of an inspection, shall be complied with forthwith if the information is available in the factory, or if made in writing, shall be complied with within seven days of receipt thereof. l[J02-A. Permissible levels of certain chemical substances in work environment. - Without prejudice to the requirements in any other provisions in the Act or the rules, requirements specified in this schedule shall apply to all factories. SCHEDULE 1. Definitions. - For the purpose of this schedule, - (a) "mg/ml" means milligrams of a substance per cubic meter of air; (b) " mppcm " means million particles of a substance per cubic meter of air ; ( c) " ppm "means parts of vapour or gas per million parts of air by volume at 250C and 760mm of mercury pressure ; (d) "Time weighted average concentration" means the average concentration of a substance in the air at any work location in a factory computed from evaluation of adequate number of air samples taken at that location spread over the entire shift on any day, after giving weightage to the duration for which each such sample is collected and the concentration prevailing at the time of taking the sample. Rules 102 to 105 pres­ cribed under section 112. Time weighted average concentration = CI TI +c2T2+ CnTn l+T2+ Tn I Ins. by G.O. Ms. No. 366, 'Labour, dated the 23rd February, 1985. R.102A] THE TAMIL NADU FACTORIES RULES, 1950 Where Cl represents the concentration of the substance for duration Tl (in hours); C2 represents the concentration of the substance for duration T2 (in hours); and Cn represents the concentration of the substance for duration Tn (in hours); ( e) " Work location " means a location in a factory at which a worker works or may be required to work at any time during any shift on any day. 2. Limits of concentrations of substance at work locations. - ( 1) The time weighted average concentration of any substance listed in Table 1 or 2 of the schedule, at any work location in a factory during any shift on any day shall not exceed the limit of the permissible time weighted average concentration specified in respect of that substance : Provided that in the case of a substance mentioned in Table 1 in respect of which a limit in terms of short term maximum concentration is indicated, the concentration of such a substance may exceed the permissible limit of the time weighted average concentration for the substance for short periods not exceeding 15 minutes at a time, subject to the condition that- (a) such periods during which the concentration exceeds the prescribed time weighted average concentration are restricted to not more than 4 per shift ; (b) the time interval between any two such periods of higher exposure shall not be less than 60 minutes ; and ( c) at no time the concentration of the substance in the air shall exceed the limit of short term maximum concentration. (2) In the case of any substance given in Table 3, the concentration of the substance at any work location in a factory at any time during any day shall not exceed the limit of exposure for that substance specified in the Table. (3) In the cases where the word" skin" has been indicated against certain substance mentioned in Tables 1 and 3, appropriate measures shall be taken to prevent absorption through cutaneous routes particularly skin, mucous membranes and eyes as the limits specified in these Tables are for conditions where the exposure is only through respiratory tract. THE TAMIL NADU FACTORIES RULES, 1950 [R.102A (4) (a) In case, the air at any work location contains a mixture of such substances mentioned in Tables I , 2 or 3, which have similar toxic properties, the time weighted concentration of each of these subs-tances during the shift should be such, that when these time weighted concentration divided by the respective permissible time weighted average concentration specified in the above mentioned tables, and the fractions obtained are added together, the total shall not exceed unity, i.e. C' + C3 + .. C" should not exceed unity when L' L3 When Cl, C2 Cn are the time weighted concentration of toxic substances l, 2 and in respectively, determined after measurement at work location ; and LI, L2 Ln are the permissible time weighted average concentration of the toxic substances 1, 2 .. . ... ... and in respectively. (b) In case the air at any work location contains a mixture of substances mentioned in Table 1, 2 or 3, and these do not have similar toxic properties, then the time weighted concentration of each of these substances shall not exceed the permissible time weighted average concentration specified in the above mentioned tables, for that particular substance. (c) The requirements in clauses (a) and (b) shall be in addition to the requirements in paragraphs 2 (1) and (2). 3. Sampling and evaluation procedures. - (I) Notwithstanding provisions in any other paragraphs, the sampling and evaluation procedures to be adopted for checking compliance with the provisions in the schedule shall be as per standard procedures in vogue from time to time. (2) Notwithstanding the provisions in paragraph 5, the following conditions regarding the sampling and evaluation procedures relevant to checking compliance with the provision in this schedule are specified. (a) For determination of the number of particles per cubic meter in item 1 (a) (i) (1) in Table 2, samples are to be collected by standard or midget impringer and the counts made by light field technique. (b) The percentage· of quartz in the 3 formulae given in item 1 (A) (i) of Table 2 is to be determined from airborne samples. R.102A] THE TAMIL NADU FACTORIES RULES, 1950 (c) For determination ofnumber of fibres as specified in item 2 (a) of Table 2, the membrance filter method 1[at 430 x magnification (4 mm objective) with phase contrast illumination] should be used., ( d) Both for determination of concentration and percentage of quartz for use of the formula given in item l (a) (i) (2) of Table i, the fraction passing through a size selector with the following characteristics should only be considered. Aerodynamic diametre (Unity density sphere) 2.0 2.5 3.5 5.0 10.0 Percentage allowed by size-selector. 20 '75 50 .25 0 4. Power to require assessment of concentration of substances. - ( l) An Inspector may, by an order in writing, direct the occupier or manager of a factory to get before any specified date the assessment of the time weighted average concentration at any work location of any of the substances mentioned in Tables I, 2 or 3 carried out. (2) The results of such assessment as well as the method followed for air sampling and analysis for such assessment shall be sent to the Inspector within three days from the date of completion of such assessment and also a record of the same kept readily available for inspection by an Inspector. S. Exemption. - If in respect of any factory or a part of a factory, the Chief Inspector is satisfied that, by virtue of the pattern of working time of the workers at different work locations or on account of other circumstances, no worker is exposed, in the air at the work locations, to a substance or substances specified in Tables I, 2 or 3 to such an extent as is likely to be injurious to his health, he (the Chief Inspector) may by an order in writing, exempt the factory or a part of the factory from the requirements in paragraph 2, subject to such conditions, if any, as he may specify therein. I Subs. by GO. Ms. No. 1717, Labour, dated the 2nd September, 1986. THE TAMIL NADU FACTORIES RULES, 1950 [R.102A R.102A] THE TAMIL NADU FACTORIES RULES, 1950 '[TABLE - 1 Permissible limits of exposure. A ( ' SI Substance Time-weighted Short-term No. average exposure limit concentration (STEL) (TWA) (8 hrs). (15 min), * � � ppm mglm3** ppm mg/1113** (I) (2) (3) (4) (5) (6) Acetaldehyde 100 180 150 270 2 Acetic acid 10 25 15 37 3 Acetone 750 1,780 1,000 2;375 4 Acrolein 0.1 0.25 0.3 0.8 5 Acrylonitrile-skin (S.C.) 2 4.5 6 Aldon-Skin 0.25 7 Ally! Chloride 3 2 6 8 Ammonia 25 18 35 27 9 Aniline-skin 2 IO IO Anisidine ( o,p-isomers )-Skin 0.1 0.5 1 1 Arsenic & soluble compounds (as As) 0 2 12 Benzene (HC) 0.5 1.5 25 7.5 13 Beryllium & compounds (as Be) (S.C.) 0002 14 Boron trifluoride-C 3 15 Bromine 0.1 0.7 0.3 2 16 Butane 800 1,900 17 2-Butanone (Methyl ethyl Ketone-MEK) 200 590 300 885 18 n-Butyl acetate 150 710 200 950 19 n-Butyl alcohol-Skin-C 50 150 20 Sec/Tert Butyl acetate 200 950 21 Butyl mercaptan 0.5 1 5 22 Cadmium Dusts and salts (as Cd) 0.05 23 Calcium Oxide 2 24 Carbary! (Sevin) 5 25 Carbofuran (Furadan) O I I Subs. by GO. Ms. No. 196, Labour and Employment (M-2), dated the 22nd August, 2013. ppm mglm3** ppm mglm3** (1) (2) (3) (4) (5) (6) 26 Carbon disulphide-Skin 10 30 27 Carbon Monoxide 50 55 400 440 28 Carbon tetrachloride-Skin (S.C.) 5 30 29. Chlordane-Skin 0.5 2 30 Chlorine 3 3 9 31 Chlorobenzence (Monochlorobenzene) 75 350 32 Chloroform (S.C.) 10 50 33 bis (Chloromethyl) ether (H.C.) 0.001 0.005 34 Chromic acid and chromates (as Cr) 0.05 35 Chromous salts (as Cr) 0.5 36 Copper Fume 0.2 37 Cotton dust, raw 0.2+ 38 Cresol, all isomers- Skin 5 22 39 Cyanides (as CN)- Skin 5 40 Cyanogen 10 10 41 DDT (Dichlorodiphenyl trichloroethane) 42 Demeton- Skin 0.01 0.1 43 Diazinon-Skin 0.1 44 Dibutyl phthalate 5 45 Dlchlorvqs (DDVP)- Skin 0.1 I 46 Dieldrin-Skin- 0.25 47 Dinitrobenzene (all isomers)- Skin 0.15 48 Dinitrotoluene- Skin 1.5 49 Diphenyl (Biphenyl) 0.2 1.5 50 Endosulfan (Thiodan)-Skin 0.1 51 Endrin- Skin 0.1 52 Ethyl acetate 400 1,400 53 Ethyl alcohol 1,000 1,900 54 Ethylamine IO 18 55 Fluorides (as F) 2.5 56 Fluorine 2 2 4 57 Formaldehyde (S.C.) 1.0 1.5 2 3 58 Fonnicacid s 9 59 Gasoline 300. 900 500 !,SC 60 Hydrazine-Skin (S.C.) 0.1 0.1 61 Hydrogen Chloride-C 5 7 THE TAMIL NADU FACTORIES RULES, 1950 [R.102A ppm "mglm 3** ppm mglm 3** (1) (2) (3) (4) (5) (6) 62 Hydrogen cyanide-Skin-C 10 10 63 Hydrogen Fluoride (as F)-C 3 2.5 64 Hydrogenperoxide I 1.5 65 Hydrogen sulphide 10 14 15 21 ss lodine-C . 0.1 I 67 Iron Oxide Fume (Fe2 03) (as Fe) 5 68 Isoamyl acetate 100· 525 69 Isoamyl alcohol 100 360 125 450 70 Isobutyl alcohol 50 ISO 71 Lead, inorg dusts and fumes (as Pb) 0.15 71. Lindane-Skin 0.5 7i Malathion-Skin 10 74 Manganese (as Mn) dust and compounds-C - 5 75 Manganese fume (as Mn) · - )· 3 76 Mercury (as Hg) • Skin (i) Alkyl compounds 0.0) 0.03 (ii) All fonns except alkyl vapour 0.05· (iii) Aryl and inorganic compounds 0.1 77 Methyl alcohol (Methanol)·Skin 200 260 350 310 78 Methyl cellosolve (2-Methoxyethanol)-Skin 5 16 79 Methyl isobutyl ketone SO' 205 75 300 80 Methyl isocyanate - Skin 0.02 0.05 81 Nephthalene 10 50 15 75 82 Nickel Carbonyl (as Ni) 0.05 0.35 83 Nitric acid 2 5 5 JO 84 Nitric oxide 25 30 85 Nitrobenzene-Skin 1 5 86 Nitrogen dioxide 3 6 5 10 87 Oil mist mineral 5 10 88 Ozone 0.1 0.2 0.3 0.6 89 Parathion Skin 0.1 90 Phenol - Skin 5 19 91 Phorate (Thimet)-Skin 0.05 0.2 92 Phosgene (Carbonyl chloride) 0.1 0.4 93 Phosphine 0.3 0.4 94 Phosphoric acid ! 3 95 Phosphorus (yellow) 0.1 R.102A] THE TAMIL NADU FACTORIES RULES, 19.50 ppm mglm3** ppm mglmJ** (1) (2) (3) (4) (5) (6) 96 Phosphorus Pentechloride 0.1 97 Phosphorus trichloride 0.2 1.5 0.5 3 98 Picric acid - Skin 0.1 0.3 99 Phridine 5 15 IOO Silane (Silicon tetrahydride) 5 7 IOI Sodium hydroxide-C 2 102 Styrene, monomer (phenylethylene) 50 215 100 425 103 Sulphur dioxide 2 5 5 10 104 Sulphur hexafluoride 1,000 6,000 105 Sulphuric acid l I06 Tetraethyl lead (as Po)-Skin 0.1 107 Toluene (Toluol) IOO 375 150 560 108 0-Toluidine-Skin (S.C.) 2 9 109 Tributyl Phosphate 0.2 2.5 I IO Trichloroethylene 50 270 200 1,080 1Jl Uranium, natural (as U) 0.2 0.6 112 Vinyl chloride (H.C ) 5 IO 113 Welding fumes 5 114 Xylene (o-, m-, p-isomers) 100 435 150 655 115 Zinc Oxide (i) Fume 5.0 JO (ii) Dust (Total dust) 10.00 116 Zirconium compounds (as Zr) 5 IO ppm mglm3 * ** t Lint c Skin s.c. H.C. Parts of vapour or gas per million parts of contaminated air by volume at 25°C and 760 torr (mm of mercury) milligram of substance per cubic metre of air. Not more than 4 times a day with at least 60 min. interval between successive exposures. mglm3=Molecular weight X ppm 24.45 free dust as measured by the vertical elutriator cotton-dust sampler. denotes ceiling limit denotes potential contribution to the overall exposure by the cutneous route including mucous membrane and eye. denotes suspected human carcinogens. denotes confirmed hwnan carcinogens.] THE TAMIL NADU FACTORIES RULES, 1950 [R.102A 1(TABLE - 2 Substance Permissible-time-weigJ,ted average concentration (TWA) (8 hours], Silica, Si Oz (a) Crystalline mg/m3 30 % Quartz+ 3 10600 mppcm % Quartz+IO JO mg/m3 % respirable Quartz +2 Half the limits given against quartz Half the limits given against quartz Same hmit as for quartz (i) Quartz (/) In terms of dust count (2) In terms ofrespirable dust (3) In terms of total dust (11) Cristobalite (m) Tndymite (zv) Sillica, fused (v) Tripoli Same limit as m formula in item (2) given against quartz. JO mg/m3, Total dust. ( b) Amorphous Silicates [ Asbestos (H.C.) (a) 'Amosite (b) Chrystolite (c) Crocidolite 0.5 fibre/cc *0; 1.0 fibre/cc***; 0.2 fibre/cc*** *** (i) For fibre greater than 5µm in length and less than 5µm in breadth wit! lengh to breadth ratio equal to or greater than 3: I (ii) As determined by the membrane filter method at 400 - 450 magnification (4mm objective) phase contrast illumination] I Subs by GO. Ms. No. 196, Labour and Employment (M-2), dated the 22nd Augus 2013. R.102A] THE TAMIL NADU FACTORIES RULES, 1950 Portland Cement I Omglm3, Total dust containing less than 1 % quartz Coal Dust 2mg{m3, respirable dust fraction containing less than 5% quartz. mppcm = Million particles per cubic mene of air, based on impinger samples by light-field techmques. * As determined by the membrane filter method at 400 - 450 x magnification (4mm objective) phase contrast illumination. Respirable Dust : - Fraction passing a size-selector with the fol lowmg characteristics · Aerodynamic Diameter (µm) (unit) (density sphere) 2 2.5 3 5 5.0 IO % passing selector 90 75 50 25 O.J. THE TAMIL NADU FACTORIES RULES, 1950 [R.102A I 03. Muster roll - The Manager of every factury shall maintain a muster-roll of all the workers employed in the factory in Form No. 25 1[and entries shall be made at the commencement of each period ofwork:] Provided that, if the daily attendance is noted in the Register of Adult Workers in Form No. 12, or the particulars required under this rule are noted in any other register, a separate muster-roll required under this rule need not be maintained. 2[The Manager shall make it readily available for inspection to the inspector at all times during working hours, or when any work is being carried on in the factory and such muster roll shall be preserved for a period of three years after the last entry.] * I 03-A. In every factory in which all or any class of adult workers are exempted from all or any of the provisions of sections 5 1 , 52, 54, 55 and 56 of the Act, a muster-roll shall be maintained inForm No. 25-A. This roll shall show the time of beginning and ending of each period of work during the day or night or both and shall be entered at the commencement of each period of work. Further in the case of urgent repairs full particulars should be given of work done by each worker on each day of such repairs including periods of normal work, if any. The Manager shall make it readily available for inspection during al working hours of the factory and such muster-roll shall be preserved for l period of three years after the last entry. 3(103-B. Service Card]. - (I) The Manager of every factor: shall maintain, in addition to maintaining a Muster-Roll in Form No 25, a 3[service card] for each worker employed in the factory in F.orn No.25B. (2) The 3[service card] after all entries are made therein for calendar month, shall be issued to the worker concerned within a week afte I Subs. GO. Ms. No. 24, Labour and Employment (M-2), dated the 12th Februai 1993. 2 Subs. GO. Ms. No. 1906, Labour, dated the 6th September, 1985. * Ins. by notification. 3 Subs. for" Time card", by GO. Ms. No. 127, Labour and Employment (M-� dated the 31st August, 2005. THE TAMIL NADU FACTORIES RULES, 1950 R.103-B] the expiry of the calendar month to which the 1[service card] pertains and his acknowledgement obtained therefor. It shall be the property of the worker thereafter : Provided that the Chief Inspector ofFactories may, by order in writing exempt any factory or class of factories from the provisions of this rule, subject to such conditions as he may impose if he is satisfied that any alternative system followed therein is adequate to meet the requirements of this rule. 2((3) The acknowledgements obtained from the workers for the issue of 1[service card] should be produced on demand to the Inspectors at the time of inspection.) 3(103-C. Identity Card. - (1) The Manager of every factory shall issue Photo Identity Card to each worker employed in the (sic.) Form No. 25-C. (2) The Photo Identity Card shall be issued to the worker within one month from the date of entry into service and acknowlegement obtained therefor. (3) The validity of the Photo Identity (sic.) shall be of permanent nature. ( 4) The acknowlegements obtained from the workers for having issued the photo identity card shall be produced on demand by the Inspector.]. 4(104. Register of accidents and Dangerous Occurrences. - ***] ' 1 Subs. by GO. Ms. No. 127, Labour and Employment (M-2), dated the 31st August, 2005, for" Time card". 2 Ins. by GO. Ms. No 291, Labour, dated the 3rd February, 1984. 3 Ins. by GO. Ms. No. 205, Labour and Employment (M-2), dated the 4th October, 2010. 4Rule 104, omitted by GO. Ms. No. 121, Labour and Employment (M-2), dated the 31st July, 2012. Prior to this Rule 104 was substituted by GO. Ms. No. 698, Labour and Employment, dated the 11th August, 1975. R.103-C] THE TAMIL NADU FACTORIES RULES, 1950 105. Maintenance of Inspection Book. - The Manager o(every factory shall maintain a bound inspection book containing the following particulars and shall produce it when so required by the Inspector or Certifying Surgeon : - (a) the exemptions granted or availed ofby the factory in Form / No.28; (b) the particulars of rooms in the factory in Form No. 29 ; and ( c) the particulars of lime-washing, colour-washing, painting, varnishing or tarring, as the case may be, in Form No. 7. The book referred to in this rule shall be readily available for inspection during all working hours of the factory and such book shall be preserved for a period of three years after the last entry. 106. The particulars of measurements of each room in the factory in which workers are employed shall be entered in Form No. 29. 107. (I) The maximum number of workers who may be employed in each workroom or work hall shall be posted prominently by means of a notice painted on the internal wall in each such room or hall. When determining the maximum number of persons permissible in addition to the breathing space required to be provided by section 16 (2), floor space of 1[2.3 square metres] in the case of existing factories and 1[3.3 square metres] in factories built after the commencement of the Act, shall also be provided for each worker working at any one time in the room, but such floor space shall be exclusive of the space occupied by machinery, fixtures and the materials in the room. (2) The Chief Inspector may, for reasons to be recorded in writing, relax the provisions of this rule to such extent as he may consider necessary, where in his opinion, such relaxation can be made having regard to the health of the persons employed in any room. *(108. Intimation of intended closure of factory. - (1) The occupier or manager of every factory shall report to the Inspector any intended closure of the factory or any section or department thereof fifteen days before such closure : 1 Subs. for " 25 square feet " and " 36 square feet " respectively, by G.O. Ms. No. 6751, Industry, Labour and Co-operation (Labour), dated the 30th November, 1961. * For Rule 108, Rules 108 and 109, substituted by G.O. Ms. No. 866, Industry, Labour and Co-operation, dated the 13th February, 1961. THE TAMIL NADU FACTORIES RULES, 1950 R.108] [R.109 Provided that in the event of a factory or any section or department thereof being forced to be closed for reasons beyond the control of the Occupier or the Manager, the report shall be sent as early as possible and at any rate within twenty-four hours of the closure . • (2) '(a) The report shall contain the following particulars, namely:- (i) the date of closure of the factory, department or section; • (ii) tJ.� reasons for the closure; (iii) the number of workers on the register on the date of the report; (iv) the number of workers likely to be affected by the closure ; and (v) the probable period of the closure; 1[(vi) .information as to the particulars and quantity of stored chemicals and action taken or proposed to be taken to ensure safety from these chemi�als while in storage during such closure.] (b) In the event of a factory closing permanently and ceasing to exist or closing for over two months, such report shall be accompanied by the licence granted or renewed under the provisions of these rules. (3) In the event of the closure referred to in sub-rule (1) being in respect of a section or department of a factory, if that section or department should start working again, the Occupier or the Manager shall submit a report within 24 hours of its re-opening furnishing the following particulars, namely : - (i) the date of resumption of work ; (ii) the number of workers on the register on the date of resumption of work; and (iii) the number of workers on the register on the date of closure now re-employed. 109. Power to cancel the licence and registration upon receipt of report. - The Chief Inspector may, on the receipt of a report in respect of any factory under sub-rule (1) of rule l 08, and after making such enquiry as he thinks fit, by order, cancel the licence and registration in respect of such factory with effect from such date as may be specified in the order.] I Ins. by G.O. Ms. No. 1852, Labour and Employment, dated the 3 Ist August, 1988. THE TAMIL NADU FACTORIES RULES, 1950 THE TAMIL NADU FACTORIES RULES, 1950 R.113] t[JIO. Preservation of records. -The records specified in column ( 1) of the Table below shall be preserved in the office of the Chief Inspector of Factories, Madras, for the periods specified in the corresponding entries in column (2) thereof: - - THE TABLE Records Period of retention Applications presented under rules 4 and 7 of the Tamil Nadu Factories Rules, 1950. Counterfoils and licences issued under the said rules Chalans. Five years from the date of disposals of the applications. Five years from the date of issue of licences. Five years from the date of issue of licences. ' 111. Manner of destruction of records. -After the period of retention specified in rule 110, the records shall be destroyed either by tearing or by burning in the presence of the head of the office.]. ·., 1[112. Language in the registers and records. -The registers and records required to be maintained in a factory under the provisions of the Act and these rules shall be either in English or in a language understood by the majority of the workers working in the factory.] 1[1�3. Exlzibition of name board. -The name board of a factory shall be displayed conspicuously at the entrance of the factory premises. The name board shall be in Tamil and wherever other languages are also used, the version in such other languages shall be below the Tamil version.]. 1 Rules 110 and 111, added by G.O. Ms. No. 6586, Industries, Labour and Co-operation (Labour), dated the 18th November, 1961. 2 Rule 112, added by G.O. Ms. No. 2385, Industries, Labour and Co-operation (Labour), dated the 27th April, 1964. 3 Rule 113, added by G.O. Ms. No. 1310, Labour and Employment, dated the 22nd June, 1981. THE TAMIL NADU FACTORIES RULES, 1950 I '[FORMNo.1 [Prescribed under rule 3] APPLICATION FOR PERMISSION TO CONTRACT, EXTEND OR TAKEN INTO U�E ANY BUILDING AS A FACTORY \(I) Particulars of the Applicant: -- (a) Name Self attested l Passport size (b) Father's Name Photograph of the (c) Designation \ Applicant (d) Age. (e) Permanent Residential Address, E-Mail ID : (f) Phone Number : (g) Mobile Number: (2) Particulars ofthe owner of the building/premises: -- (a) Name: (b) Father's Name : (c) Age: (d) Permanent Residential Address, E-Mail ID : I (f) Phone Number (g) Mobile Number =I (3) Particulars of factory : -- (a) Full Name and postal address of the factory : I (b) E-Mail ID : I (c) I Mobile Number: I (d) Web site address, If any· I (4) Situation of the Factory and Survey Numbers I Door Number of the factory with relevant documentary proof for the occupancy I ownership of the factory (a) State: I (b) District: (c) Town or Village · I (d) Nearest Police Station : I I Subs by GO. Ms No 10, Labour& Employment(M-2) dated 27th January, 2014. (e) Nearest Railway Station or Steamer Ghat : (5) Purpose for which plans are submitted : -- State whether initial approval I additional installation/additional construction I changes in installation, etc ; (6) If the plans have been approved earlier, give the number and date of approval of previous plans relevant to the present plans except in the case ofinitial approval (7) Details of present proposals with reference to item number 5 (8) Total installed capacity in Horse Power (including the present plans) (a+c-b) : (a) Approved Horse Power in the earlier plans : (b) Deletion, if any : (c) Addition: (9) Maximum Number of workers proposed to be employed in the factory : (10) Brief description of the manufacturing process with flow chart (II) Details of chemicals with storage quality, if any: Serial Name of the Type of Maximum quantity Number chemical. storage Stored in tonnes (I) (2) (3) (4) NOTE : Court fee stamp to the value of Rs.2/· (Rupees two only) to be affi: the first copy only. Place: Date: Signature of Appl THE TAMILNADU FACTORIES RULES, 1950 TAMD... NADU FACTOFIES RL'l.ES, 1950

Previous and next

All provisions of The Tamil Nadu Factories Rules,1950

Questions people ask

Is appendix of the Tamil Nadu Factories Rules,1950 still in force?

No repeal of the Tamil Nadu Factories Rules,1950 is recorded.