Regulation 184, Indian Boiler Regulations, 1950: Longitudinal Seams
Indian Boiler Regulations, 1950 - Regulation 184
Text of regulation 184
Longitudinal Seams
184. Longitudinal Seams.—The longitudinal seams of furnaces may be
either:
(a) Forgo Lap Welded.
(b) Fusion Butt Welded,
(o) Riveted.
Longitudinal seams of furnaces exoeeding 3/8* thickness shall uot be riveted.
125. Fusion Welded Longitudinal Seams.—Where the longihidinal Keam is
fusion welded tho following precautions shall be observed :—
(a) Plates over 5/8 in. in tliicknosH shall be bevolled from both sides of oaoh
abutting edgo, but the bevel need not necessarily be the same on each side (HPO Figs.
1 and 2). Plates less than 5/8 in. in Lhicknesa may be bevelled from ono aide only
of eaoh abutting edge (soe Figs. 3 and 4).
The included angle of the bevel shall be not less than 60° ,nnd the bevelling
may be any one of tho forms shown in Figs. 1—4.
Fig. 6. Fusion Welding oJ Gross Tubes ol Vertical Cross Tube Boilers.
(b) In ordor to obtain full penetration of the weld metal a gap shall be main-
talned between the plates when they are being welded. Joints shall be welded
from both aides, and the dag shall be removed after making eaoh run. Before
044 THE GAZETTE OF INDIA EXTRAORDINARY [PART U
the socond side of the joint is welded tuiy slag 01 defect at the bottom of the first)
run shall be remoxed by grinding, chipping or machining. There shall be no appre-
ciable undercutting of the plate.
(c) Por the purpose of relieving internal stresses the plates adjacent to a fusion,
•weld shall be efficiently annealed after welding, and when the firebox i« forge-welded!
it should be allowed to cool gradually.
126. Furnace Crown.—(a) Tho furnace crown f.eum shall not fa 11 in line with
any circumferential scam of the boiler shell.
(b) the furau.ee crown nmy be riveted to tho vertical portion of tlic fijphox, or
alternatively, the ioint nitty bo fusion hu1t welded by the electric are process, pro-
vided the conditions, as to fusion welding in Regulation 125 are observed. Where
the joint is to be welded the edges of tho furnace crown and the firebox body shall
be bevelled in accordance with Tig. 3 or Fig. 4. The depth of tho flange of the
furnace crown •plate from the commencement of tho curvature of the flanging radius
shall be not lesi« than four times the plate thickness with a minimum of 1̂ inches.
On completion of voiding the fiiebox nh&ll be effectively stress relieved by heat
treatment (net JHO Ke^. 128.)
127. Cross Tubes.—(a) Cross tubes shall b< made from wckllesB .stoel tube or
from plate or strip rolled and forgo water gas welded. Where welded tubes are
used the longitudinal welds shall be so situated that they are not exposed to the
direct impact of the flame.
(b) The minimum thioknees shall be 5/16 in,
(c) Where cross tubes are flanged and riveted to the furnaoe, the flanges shall
bo set to the ourvature and taper of the furnace, and shall be a good fit before rivet-
tog-
(d) Where welded construction is employed the tubes shall be of sufficient
length to enter the furnace plate and be flush with the water side all round or project
not more than 6/8 in. into the water space at any part of the circumference. Where
the tubes are fusion welded in position, the firebox plates shall be suitably ohamfored
and the joints shall be welded externally and internally (see Fig. 5).
128. Uptakes.—(a) Tho uptakes shall be foimed from woldless., forge water gas
welded or fusion butt welded steel tube and shall be securely riveted to the fur«
nace crown plate and riveted to the shell crown plate.
(b) As an alternative to riveting, the uptake may be fusion butt welded by the
electric arc process to the upward flange of the opening in the fire box crown plate
provided the conditions ajs to fusion welding in Regulation 125 are observed. The
edges of the upward flange and the adjacent end of the uptake shall be bevelled in
accordance with Fig. 3 or Fig. 4. The depth of the crown plate opening from the
commencement of the ourvature of tho flanging radius shall be not less than twice
the plate thickness with a minimum of 1 inch. On completion of welding the
uptake and crown plate shall be effectively stress relieved by heat treatment.
Where the firebox crown plate Is also fusion welded to the body of the fire-
box, the firebox complete with uptake shall be effectively stress relieved by heat
treatment on completion of the welding.
(c) Welded uptakes shall be so arranged that tke weld is directly facing the
longitudinal centre line of tbe manhole.
129. Loco Type Fireloxcs.—(n) The foundation M>sm whall be of rivetul con-
atruction but all other seams may be welded subject to the depth of the flange
being such that the welded seams fall between the 1st and 2nd rows of screwed
«taye or between the flange and the adjacent row of sorewed stays.
Sue. 8] THE GAZETTE OF INDIA EXTEAOBDINAEY 645
(b) The firohole mouthpiece may be similarly welded when the firebox and
shell are flanged for the purpose.
(o) The welding shall oomply with Regulation 125.
STAYS
130. Bai Stays.—JSar staya shall not b<i w^Mod at any part. They Hhall pre.
ferably have plus threads, the ends of the stays being upset or the middle portion
being reduced for this purpose. Stay bars -which have been worked in the tire shall
be subsequently annealed.
131. Longitudinal Stays.—(a) Longitudinal and nmnlai solid SUIVMI hta\s
shall be efficiently secured with nuts at euch end and not merely riveted over.
Where they are over 12 feet in length, they shall be supported at intervals of fl ft.
along its length,
(b) Where the stay is screwed through both platos, the stay and h
Previous and next
Questions people ask
Is regulation 184 of Indian Boiler Regulations, 1950 still in force?
No repeal of Indian Boiler Regulations, 1950 is recorded.