LawGrids logoLAWGRIDS.ORG

Regulation 835, Indian Boiler Regulations, 1950.: General

Indian Boiler Regulations, 1950. - Regulation 835

Text of regulation 835

General

835. General.—(a) Feedoheck valves shall be of the non-roturn type. (b) Where the valve is not of sorew-drown non-return type a separate aorew* down valve shall be provided. (o) The discharge from the feed cheok valve or from the internal feed pipe (if provided) shall be above low water level and in the case of Lancashire and Cornish boilers shall be at least 5ft. beyond the fire bridge. 336. Operating position.-—Feed chock valves or regulating valves shall be so arranged as to enable them to be satisfactorily operated from the boiler floor. CHAPTER VH SUPERHEATERS TUBES 337. Material and Construction.—See Reg. 151. 338. (a) The Working Pressure of tubes shall be determined by the following formula :— W P = ~ (T-C) (Eqn. 87). Where T=Minimum thickness of tube in inohes. W.P.=Boiler drum working pressure in 1b. per sq. in. D=Outside diameter of tube in inches. f= Permissible working stress in lb. per sq. in. at working metal temperature See Table below. C=Constant as follows :— Cold Hot Drawn Drawn Tubes. Tubes. For generating tubos and unprotected furnace wall tubes C—O-OG C—0-08 The working metal temperature shall be taken as : (a) For boiler tubes, the saturation temperature corresponding to pressure W.P. plus 25° F. (6) For convootion superheater tubes, the maximum steam temperature for which the tube is designed plus 50°F. (c) For radiant superheater tubes the designed maximum steam tempera- ture plus more than 50°F, the amount depending upon the super- heater design. i!4 1. .x, GAZETTE OF INDTA EXTRAOEDINAEY [PART H Permissible Working Stresses for Tubes. Table. Working metal temperature Upto flflO'B1 700°F 7fiO°F 800°F 8S0°F 0OO°F 06O°F 975°F 1000°F . . . . 1025°F . . . . 10fl00F Low oarbou stoel tubes t o Kog. 36 and 43 10,000 lbB./sq. iu."l MOO " " " 1 9,000 " " " i. 8,000 " " " 0,800 " " " J 6,600 Molybedenum J% steel tubes 12,000 ] 1,600 8,400 6,100 4,500 1% chrome J% molybdenum ateol tubes 12,000 11,600 9,800 8,400 7,000 5,760 4,500 Intermediate values may be interpolated.— (b) In no case, however, shall the (standard wire gauge) of tube ae supplied be lesa than thoae given in the following table— [Subjeot to the tolerances Regs. 36 (d), 43 (d), 48 (c) and 53 (o).] Table. Outside diameter in inchos TJpto and including 2 . . . . . . Over 2, up to and including 3 Over 3, up to and inoluding 3A . Over Sj> up to and inoluding 4J . Woldleaa tubea Hot nninbed SWG 10 10 10 9 Cold drawn SWG 13 12 10 9 (o) Where tubes are bent the resulting thickness of the tubes at the thinnest part shall be not less than that required for plain tubes. HEADERS AND SIMILAR PRESSURE PARTS 339. Material and Construction.—Soe Rogn. 154 & 244(b). 340. Rectangular Headers Symmetrical in Form.- (a) The Working Pressure shall be determined by the following formula :— f ( t- l )2 W.p. = — ~ Eqn. (88) b* x C Wbere W.P.=The working pressure in lbs. per sq. in. t=The thickness in 1/32 in. b=-The breadth in inohes between the supporting sides of the header less one inside corner radius ' r ', this being the corner radius of the reotangular box from which the header Is pressed or of the header casing, which shall be not leas than 1/4 in. In no case, however, shall' b ' be taken as less than 0 • 9 of the breadth bet- ween the supporting sides. "SEO. 3] THE GAZETTE OP INDIA EXTEAOBDlNAItY' 715' C=300 for wrought stool and 350 for steel oastings : where the sides are corru- gated or otherwise reinforced by substantial supports so that the length of the flat portion between the corrugations or supports does not exceed ' b '. ' C ' shall bo taken as 175 for wrought steel and 200 for steel castings. f=The permissible stress at working metal temperature lbs. per sq. in. see table below. (b) If the faces of the headers are machined locally at the tube holes or hand holes the thickness at that part may be an much as 6/32 in. less than given by Equa- tion 88 but irrespective of the thioknoss obtained by the use of the formula, the thiokness of the headers at tho tube holes in 1/32 in. shall be not less than : t = 3Xy rd+8 Eqn. (89). Where d—The diameter of the hole in inches, and in no case shall the thiok- ness be less than 10/32 in., except that in small patches not exceeding one-half a sq. in. in area, the thickness may be 50 per cent, of the thiokness used in Equation 88. (c) The permissible stress at working metal temperature shall be as given in the table below. TABLM Working metal temperature tTpto saorF . . 800°F 650°F 700°F 750°F 800°F 850°F 900°F FormiBSible stress in lb/sq. in. Wrought steel having an ultimate tensile stress in tons per sq. in. of :— 24-28 12300 12300 12300 J1H0O 10000 9300 7800 (1300 26-30 13300 13300 13300 12800 11600 10000 H300 6300 28-32 14300 14*300 14300 13800 12300 10500 8500 0300 32-36 16300 16300 10300 15800 H000 11800 9200 630O 34-3S 17300 17300 17300 16800 14800 12400 t>000 6300 Oast CIJ. T oteel 28-3fi tona sq. in. 10000 9000 8000 7880 7200 0700 6300 4400 Intormocliato values muy bo interpolated. The working metal temperature shall bo taken as :— (d) "For saturated steam, Mater drums, muddrums and hoaders, the saturation temperature corresponding to the pressure WP plus 50°F. (e) For superheater headers tho designed maximum steam temperature for that header plus 50°F. (f) Where headers are adequately protected from the gases of combustion or swept by such gases in the third or subsequent pass of a boiler, the working metal temperature shall be taken as the saturation or designed maximum steam temper- Aturo as denned above, whichever applies. A oovering of refractory or insulating 71« x, Jfi G A Z E I J . ^ OF INDIA EXTRAORDINARY [EAIW H - material which may be liable to become dislodged shall not be deemed adequate' protection. 341. Headers Irregular in Form-—In oasos where the headers are of sueb, irregular form aa to render impracticable the application of a formula for the determination of thickness, the manufacturer shall show the suitability of tk» headers for the working conditions by indicating practically the maximum internal hydraulio pressure which a header, made to the same design and of similar material,, will withstand without permanent deformation. The maximum working pressure for similar headers may then be determined by the following formula :— Permissible stress at working metal temperature W.P.=PXX Eqn. (90). FxC Where W.P.=iThe working pressure in lbs. per sq. in. P ^ T h e maximum internal hydraulic pressure withstood without permanent deformation. F=l -75 for wrought steel and 2 for cast steel, C=15 500 for wrought steel of 24 tons per sq. in. minimum ultimate tensile stress, = 16 500 for wrought steel of 26 tons per sq. in. minimum ultimate tensile stress, = 18 000 for wrought steel of 28 tons per sq. in. minimum ultimate tensile- stress, =21 000 for wrought steel of 32 tons per sq. in. minimum ultimate tensile stress, =22 000 for wrought steel of 34 tons per sq, in. minimum ultimate tensile stress, and = 15 500 for cast steel of 28 tons per sq. in. minimum ultimate tensile stress. 342. Cylindrical Headers.- Whom cylindrical headers aro provided their working pressure shall be determined by Equation 72. CHAPTER V m STEAM PIPES AND FITTINGS 343. Steam pipes may bo wrought iron, wrought steel, cast SIOPI and in some- cases of copper. Steel pipes may be solid drawn (cold or hot finished) or lap welded. Wrought iron pipes may be lap welded. Copper pipes shall be solid drawn and no- pipe made from the electrode position of copper on a mandril shall be used for steam delivery. MATERIAL 344. Steel pipes—(a) These pip- H J»>11 lx medo by tho open hoartk or an electrio process acid or basic. Where the material is used for designed steam temperatures above 75©JF, the st"> •! shall be "f non-segroguted or fuller killed tvpe. ffadift} ' Jr. Jfil&A ,1 . 0* 1 DHL-WL.j.Mhk ̂ i . Ai w ' ' ' H i (b) The material from which these pipes are made shall conform to the following requirements :— Set Table 1. TABLE 1 Kind of pipes Ultimate tensile stress in tons per sq. in. Not less than Not more than Min. elongation per oent. On 8 in. i* thiok and over Less than i* thiok On iin. thiok trod over 2 in. Less than i* thiok Sulphur Maxim- mum % Phos- phorus maii- mum % Cold drawn Weldless Steel Pipes Strips out from the pipes and tented in their ourved condi- tion. Tost lengths taken from finished pipes (enda of pipes to be plug- ged for ffripR) 23 23 30 30 20 2G 18 23 30 * * • 05 Hot-finished Weldlesa Steel Pipes Stripe out from MIP pipeH and tustod in thfiir curved condition Teat lengths taken from finished pipes (ends of pipes to be plug. ged for grips). S3 23 Jo 30 20 2S lft 23 W 80 'CO •06 Roll Lapwelded Steel Pipes ^tripa out rroin thn pipes nlnur of tho "welds iui(i tested in thi ir curved nondi- tion. Test lengths tftknn from finished pipew fondrt of pipes to UP pluer- ged for s îps) 22 28 28 20 25 18 23 32 30 * • •06 •Of) •718 THE GAZETTE OF INDIA EXTftAOEDINABY [PAET H Hydraulic (water gas) Lapwefded fileel Pipes Selooted samples cut transversely Ulbimate tensile Htrefw Min. Elongation per oont. on H in tonH per RCJ, in, in. JS'ot lf>«H Infill 22 Not nioro tllHIl 28 {" thick and ovpr 2V l..eiiH than i" thick and not leas than i" Ihiok 20 LGHH than I" think 18 Sulphur ma^i- unim o//o •on Phos- phorus maxi- mum 0/ • 0 5 345. Condition of pipes.—AH Pipes shalJ be commercially straight frco from longitudinal seaming, grooving, blistering or other injurious surface marks. The ends of the pipes shall bo out square. MECHANICAL TEST 346. -Flattening test (For pipes upto and including 4-in. nominal tore).— A ring not less than 2" in length cut from ono end of each selected pipe shall when cold withstand, without showing oither crack or flaw , being flattened between two parallel flat surfaces until when the pressure is released the interior surfaces of the test pieoe remain at the middle a distance apart equal to 4 times the thick- ness of the pipe. 347. Cold bend test (For pipes over 4-in. nominal bore).—(a) A strip 1JT -wide out oiroumferentially from one end of each selected pipe shall when cold withstand, without showing either crack or flaw, being doubled over in the direction of original ourvature round a bar, the diameter of the bar being :— For pipes upto and including 3/8" thick . 3 times the thiokness, For pipes over 3/8" thick . . . 4 times the thickness. Bend Test on the Weld.—(b) A wi rip 1£" wide out eiroumforentially from one end of eaoh selected pipe with the weld near the middle of the strip, shall when cold withstand, without showing either craok or flaw, being doubled over in the direo- tion of original ourvature round a bar, the diameter of the bar being equal to eight times the thickness of the test pieoe, the weld being placed at the point of maxi- mum bending. Additional test.—(o) Should a pipe selected for testing fail in any one or moro of the tests specified above, two further tests of the same kind may be made from the same or other pipe. Should either of those fail, the pipes represented may be reheat treated and then rotested. If the repeat test aro satisfactory, the pipes shall bo accepted provided they comply with other requirements but if failure again occurs, tho pipes which the tost pieces roprosont shall be rejected. 348. (a) The process of welding lap jointed seams shall be by hammering or rolling the joint. (b) On completion of any work which involves heating, whether for welding the joint, welding on flanges, hot bending the pipe or for any other purpose, the pipe shall be carefully annealed. 349. The pressure and temperature limits within which pipes, tees, branches «to., shall be used shall be in accordance with Table 2. BriCh ft] THE GAZETTE OF INDIA BXTEAOBDINAEY 719 WORKING PRESSURE OF STEAM PIPES 360. Steel and Wrought Iron Pipes.—The maxim'im working pressure allowed on steel or wrought iron pipes shall be determined by the following formula :— 2Se. (f~9) W.P. = Eqn. (91) 100 i) £=minimuin thickness in hundredths of an inch. W.P.=Working pressure in lbs. per sq. inch. D=* Outside diameter of pipes in inches. S=Allowable stress in lbs. per aq. inch as specified in Table 3. e = efficiency factor— 1 for weldless steel pipes, •t for welded steel or iron pipes for values of t up to andinoluding 7/8", •86 for welded steel pipes for values of t over 7/8* and upto and in- cluding 1-1/8*. -8 for welded steel pipes for values of t over 1-1/8". 361. Cast steel Pipes.—(a) Th« material shall comply with Regulation^ 73_to 80, i.e., 28 tons minimum tensile stress. (6) The maximum working pressure allowed on oast steel pipes shall be deter* mined by the following formula :— 2S(«~-015 dt— -25) W.P. = — — - . . . . Eqn. (92) di <=minimum thickness in inches. W.P. =• Working pressure in lbs. per sq. in. d=internal diameter of pipe in inches. dx =oexternal diameter of pipe in inches. S = allowable working stress in lbs. per sq. in. as specified in Table (4). 352. Copper Pipes.-—(a) Tho material whall comply with Regulation 35. (b) Copper pipes may be used for a working pressure not exooodinsj 180 lbs. The external diameter shall not oxceod 5-in. (e) Copper pipes shall not be used for superheated steam. (d) The maximum working pressure on such pipes shall be determined by the following formula :-— fiO(«-3) . Eqn,(93) W.P. -= I) •• minimum thickness in hundredths of an inoh. W. P, •• working pressure in lbs. per sq in. D =• outside diameter of pipe in inches. 720 THE GAZETTE OF INDIA EXTRAORDINARY [PABT J.L TABLE 2 (Maximum permissible W. F. and Temperature) Haterinl Mild etMl WrougTit Iron . Cast Steel Copper Mothod of manufacture Cold drawn weldlese. Hot finished weldlesa. Hydraulio Watergas lap- welded. Roll lap-welded Roll lap-wolded Castings Solid drawn , Maximum permissible pressure in lbs. per aq. in. No restrictions Do. Do. 300 280 No restriction Upto and includ- ing 6*.. 180. Maximum permissible temperature in °F. 900 000 000 COO 425 two Tom L Straight*, bonds or toe*, etc.J Do. Do. Straight*, bends or tees, «to. Straight!, bends or tecs, etc. Straight* and bands. TABLE 8 Maximumipennissilile working Stress In lbs. (Values of S) Pipe* Cold dTawn Weldless Steel, Hot finished l̂ eldleuH^ Steel. Sydraub.0 (Watergon) lap-welded steel- boll lap-welded Steel. Lap-wolded Sfon. / 7600 PenniBaible Working Stress in lbs. per aq. In. for design temperature in "F. 428° 500° 11200 10000 10000 500° 550° 11200 10000 -• •• 650° 600° 10000 9000 •• •• 600° Over 650° 700° Up to and inoluding 680° 8800 8000 700° 8400 7660 750° 8000 7200 Not used foi 750° 800° 7500 8750 800° 850° 7000 6300 850* 875* 6800 6180 these temperatures. Not ua*d for fhwe tempMat«r«*. 875° 900° 4880 4400 JWiC. V\ THE GAZETTE OF JNDIA BXTJIAOEDXWAJIY 721 TABLE 4 Mazimnm permissible working stress in lbs. for cast steel (Values of S) Permissible working stress in lbs. per sq. in. for design temperature in "F Over 550° 900° 650° 700° 780° 800° 850" 875° Up to and inoluding C80° 10000 600° 9000 650° 8000 700° 7560 7 G0° 7200 800° 67B0 8B0° 8300 870" 5280 000* 4400 ATTACHMENT OF FLANGES 353. Flanges of Iron and Steel Pipes.—(a) Flanges of iron and steel pipes may- be made of oast steel wrought iron or wrought steel made -without a weld. They may be seoured to the pipes by screwing, riveting or welding. (5) No flange or blank flange of oast iron shall be attaohed direotly to main steam pipes or form part of main steam piping. (o) Blank flanges shall be of mild steel or oast steel and shall be not less in thickness than the flanges to whioh they are attaohed. 354. Screwed on flanges.—The pipes may be sorewod into flanges with a disappearing thread and expanded. Suoh sorewed and expanded flanges may b« twed for steam for a maximum pressure of 450 lbs. per sq. in. and/or a maximum temperature of 750°F and for feed pipes for pressures up to 600 lbs/sq. in. Sorewed and expanded flanges may in addition be seal welded. 355. Loose Flanges.-—Looao flanges may bo used whore the joints are made by metal to metal faces integral with the ends of the pipes. Alternatively these joints may be welded or seal welded. The loose flange shall oonfonn to th© table given in Appondix E. Where the joint is formed by integral flanges, these after maohining shall be not less in thickness than the designed thickness of the pipe as calculated by Equ- ation (91). 356. Riveted on flanges.—(a) Riveted on flanges shall only be used for pipes of 7* bore and above and for a maximum pressure of 850 lba. per sq. in. and/or a maximum temperature of 750°F. (6) The shear stress in the rivets sbp.ll not exoeed 6000 lbs. per sq. in. when oaloulated by the following formula :— ( AoxP X I F.qn. (84) AN / /** i~BE -GAEEiW OF INDIA EXTRAOBDINARY fPAETH Where Sr = the shear stress in the rivets in lbs. per aq. in. A, = cross sectional area, calculated on outside diametor of pipe in sq. inches. P = working pressure in lbs. per sq. in. N = number of rivets. A = Area of one rivet hole in sq. in. (c) The stress in the pipe shall not exceed that specified in Table 3 when cal- culated by the following formula:— (AoxP) Sp = . . . . Bqn. (95) (Ao—Al)—(Nxdxt) Where Sp = the stress in the pipe in lb. per sq. in., Ao, P and N have the values given above, and AI = crosss sectional area, calculated on inside diameter of pipe in sq. inohes. d = diameter of rivet hole in inohes. t = minimum thickness of pipe in inohes. (d) The flange hub thioknees shall not be less than 0-2 in. thicker than the minimum thickness of the pipe. (e) The distanoe from the edge of the hub to the centre line of the rivets shall be not less than one and a half times the diameter of the rivet hole. (/) The pipes shall first be properly expanded into the flanges or alternatively the flanges shrunk on to the pipes the rivet holes shall then be drilled through the pipe and hub, and the holes afterwards countersunk to remove burrs. (g) After riveting the flango hub shall be fullerod at the back. 367. Weldfd on flanges.— (a) W w i flanges arc wolded on, the welding shall be oarried out by tho oxy-acetylene or electric process. (b) The proportions of the welds in the case of metallic arc welding shall be as indicated in Figs. 28-32, tho respective working condition for each type being as follows : Figs. 28, 29 and 32: for all pressure and temperature conditions Fig. 30: for pressure condition up to 250 lbs. and temperature not exceeding 700°F. Fig 31 : for pressure conditions up to lfiO lbs. and temperature not exoeed- ing 500°F. (c) (i) Eleotrio Welds made in accordance wilh figure 32 shall be etreaa- reheved. (U) Similar wolds mado in accordance with Fig. 28 or 29 shall be stress relieved when practicable. (Hi) Flanges for use at temperatures over 700°F. which are welded by the oxj- aoetylene process shall be normalised. (d) For sizes up to and including 12" bore bossed or hubbed flanges may be used in Figs. 30 & 31. (e) Welded on flanges may be screwed on to the pipes prior to welding. #& \.;fr I£2&I 6 A X B T * B OF INDIA m.T$A<m&m2&¥ 723 Fig. 28. For all pressure and temperature conditions. A B 0 D E a t but not lesa thfm J in anr]-nnt more thfm 3/4 in. t t but not less tlinn 3/8 in. 1J t but not IOBH than 3/8 in. 1J t but not loss than 3/8 in. t but not loss than 3/8 in. and not more than 3/4 in. t but not leaa than 1/4 in. ,Xt JL, Jfl (HiSTTE OF INDIA BteAOHDINARY [PAET n Fig. 20. For all pressure and temperature conditions. A B C D E F Q 1/2 t but not less than 3/18 in. 1/4 in. Min. for Tubeu up to and Including 8/16 in. thick, t— 1/18 in. for Tubes over 8/16 in. thick and up to and inoluding 9/10 in. t— 1/8 in. for Tubes over ft/16 in. thick and up to and inoluding 7/8 in. t— 1/4 ia. for Tubes over 7/8 in. thick and up to and including 1 in. t but not leaa than 3/8 in. H t but not less than 3/8 in. H t but not leas than 3/8 in. t but not leBB than 3/8 in. and not more than 3/4 in. t but not leas than 1/4 in. &W. **J 1 , i ( AZ, ,l4.JJi UJ! JL 1UA . AA^. A t JO. .. A B C D 1J t but nnt lesa than 3/8 in. 1^ t but not leas than 3/8 in. t t but not less than i in. Fig. 30, For preesnie conditions^up to 260 lbs. and temperature not exceeding 700° F. A B C D J t but not loai than 1/16 in. 2 t i t Fig. SI. For prewnie conditions upto 160 lbs. and temperature not exceeding 600°F- , , x, JB o, JIJAJ.. p Or -L DIA jaXfcRA.O&i)ltfAlt* [&JLX* 11 Fig. 32. For all pressure and temperature conditions. A B Q t-1-1/10 in, 1/10 in. inm, 1/16 in. mm. 1 >wh(*rv t IN not greater than 1/2 in. j Where t is greater lhan 1/2 inch. ' U ' ahapea groove as shown may be used. r h g B 15° min. 1/8 in. 1/8 in. mrvx. 1/8 in. mm. J in. max. 1/18 in. mm. 368. Flanges of copper pipes.—Flanges of copper pipes may be made of brass or bronze. When flanges tiro attaohed to oopper pipes by brazing they shall be BGourod in such additional way (e.g. by riveting the onds or forming a oonioal end so ae to fit into a ooruoal bora in the flange that the resistance to withdra-wal from the flange doos not depend wholly on the brazing). 359. Standard Flanges.—Tho size and thiokness of flanges and the number and Biz© of their bolts should be as shown in Appendix E. 360. Joints— (a) Those* Regulations provide for ordinary bolted flange joints. Speoial types of joints may be used, subjoct to tho approral of the Chief Inspector. Bao. 4] ' M f t ' & A & B i T B d F I r tDIA EXTBA0.ILL».L1?A_ ,1 <*< (6) All steam pipes with butt welded circumferential joints having a wall thick- ness of 3/8* and above or oarrying a pressure of over 50 lbs. shall bo effectively stress relieye. (c) Such butt welded joint shall conform to standard specification. STEAM PIPE FITTINGS AND CONNECTIONS 361. Wrought Bends.—(a) Wherever practicable tho radii of bends (on centre lino) shall be not loss than those given below :— Bore up to and including 6 in. R—3xd „ ovor 6 in. Tip to and including 9' R = - 3 5 x d „ over 9 in. up to and inoluding 12" R=3*5xd „ over 12 in. up to and including 15" R=»4'5xd „ over 15 in up to and including 18' 11=5yd „ over 18 in. up to and including 20" R=5"5xd Where d=the boro of the pipe, R=Radius of bend to oontre line of pipe. (&) Tho thickness of pipos from which such bends are made shall be not less than 12\ per oont. granter than the minimum thicknoss required by Equation 91. Where smaller radii are neoossarv further allowances shall be made for thinning at Iho bank of the bend. Alternatively some speciu) form of construction shall be adopted to provent undue thinning. 362. Branches, Tees, etc.—!>• ' dies, bowses and drain poolwvta shall be welded to the pipes. WheiM a branoh i'i v tal size to the mail pipe an approved type of re- inforaement shall bo employed. JTor proasures ovor 350 lb./sq. in. and/or temperatures of 750°F or ovor, branches of 0 in. bore and largor shall bo woldod inside as woll as outflido. Alternatively to tho wolding on tho inn.do of tho pipe, an approved type or ro-inforcemont or moohaniral look may bo providod. 383. Blow-iown pipea.—-(«) Blow-down pipos which enn bo subjected to full boiler ])roHBuro shall be co'iwidorod as saturated stoam pi]jcs at that pressure. (6) "BloAV-down pipos wlii-'h cannot Lo subjected to fall boiler pressure shall be considered as saturated steam pipos at half the working pressure of tho boiler." 364. Valve Chests.—(a) Cheats of stop-valvos, iaoloting valves, reducing valves steam traps etc;., forming parti* of wrought iron or wrought steol main stoam piping •when for uso with saturated fttoum up to a gaua;o pr< ssuro of 100 Ibo. per square inch or a temperature of 400°J\ may be mo do of oast iron, oast steel or wrought steel in accordance, with the requirements of Regulation 290. (5) When superheated steam is used abovo 400°F. or whon pressures are above 160 lbs, per sq. in. gaugo, such chests shall bo made of oast or wrought steel or other approved material in accordance with the requirement of Regulation 200. 365. Steam Receivers, separators, etc., lor temperature exceeding 5C0T.—(a) If suoh vossels aro fusion woldod tho manufu/ turo and tests shall conform to Chapter V- (6) The working pressure of all parts shall be determined by the appropriate formulae givon in Chapter V. (c) All mountings for the above and for connected steam pipe ranges shall be of oast steol or other approved material. 366. Steam Receivers, separators, etc. for temperature not exceeding 600°F.—(a) The shells of steam receivers, steam separators, steam driers, catoh waters, drop legs, interceptors, etc. may be made of steel plates or steel castings. IJfclJB Oflja. 1XJ5 Ur JUNULA Ja^J-XiAU. JiJNA. ,J. [ i i l l f ±J (b) (i) When fabrioated of steel plates the Beams may be riveted or welded. (ii) When riveted the working pressure for the parts shall be determined by the formulae prescribed for corresponding parts of boilers and the- hydraulio tost pressure to which the vessel shall be subjected on com- pletion shall be that proscribed for boilers. (Hi) Exoept where such vessels are fusion welded in aooordance with Chapter V the longitudinal weld of vessels exceeding 15* internal diameter shall be oovered by a butt strapi (iv) For such welded seams tho standard co-offieient 0 of Regulation 176 to be used in determining the working pressure shall be 3-0 for both welded and Wolded and strappod seams. The strength porcentage to be allow- ed for the wold shall be 50 and J, the strength percentage to bo allowed for welded and strapped soarns shall be determined in accordance with Regulation 180. (v) • Branches for attachment of steam piping shall be flanged and be either flanged and riveted or wolded to the vessel. When welded this shall be done inside as well as outside where practicable. Alternatively to tho welding on the inside of the vessel an approved type of reinforcement or meoharjeal lock may be provided. Whore a branoh is of equal size to the vessel the opening shall be reinforced. (vi) All welded vossels shall be stross relieved. (c) (*') Where made of cast steel the shell shall oomply with the requirementa of Regs. 73 to 80. (ii) The working pressure for flat end platos of oast steel shall be determined by the formulae for flat end plates T wrought steel. (d) Suitable arrangements for drainage sha±i oe fitted to all vessels intonded for use in the separation of condensed stoam. Whore automatic drainage is not provided a glass water gango of sribfitanlial make to indicato the wator levo] in the vessel and a substantial drain cock or valvo shall be fitted. 367. Screwed and socketed Joints.— Couplings or Rockets inny bo uwtd on pipe up to 4 in. internal diameter vriih pronnuros up 1o 120 lbs. por square inch gauge and up to 5 in. diamitKr with prubHinxs up to 100 lbs. por square inch gauge. In all other oasos, flanges \\Ah bolts and nuts shall bo used. 368. Other fittings and Mountings.— (a) Vfllvo diesis of bronze for Mop valves up to 3 m. diameter of boro may ho attached directly to iron and stool steam pipes when pressures do not exoood 120 lbs?. Tier wq.in. gauge and ttttnporature not exceed- ing 425* 1\ Tho attachmont may bo by direct screwing to tho steam pipe or by means of flangeg. (b) Drain codes and valves may be attached to stoam pipes either by flange and bolts or be screwed into a bows formod on tho pipe. 369. Reducing Valve.- Wlwn a reducing valve is install. <d in a piptf lino, the pipe line and accessor-ion on tho low pressure side of the reducing valvo shall be protected by a suitable safety valve or valves HO adjusted as to permit tho steam to escape as soon »s th« safe Working pressure is oxooodod or by u, suitable appliance for cutting off automatically the supply of steam as soon as tho safe working pressure is exceeded. 370. Flexibility.—(a) Tho use of sliding expansion joints is prohibited. The nooessary degree of flexibility shall be obtajnod by the use of special expansion joints, or tho pipes shall bo pra-stressed initially when cold by loaving gaps at appropriate oints and pulling these up when erecting the piping. The amount of tho cold spring ago. .9] THE GAZETTE OP INDIA BXTEAORDINA!R^ 11& shall bo not less than 50% of the total expansion of the length under consideration and may be groater than this in easos where it is necessary in order to koop within the permissible stress value shown in tables 3 and 4. (6) Tho allowanoe for expansion per 100 ft. of piping at various temperatures shall be based on Table 5. TABLE 5 EXPANSION ALLOWANCE Ktmgo of temperHLuTH Dctfreei Fahronhmt 00-250 60-300 00-350 80-400 80-450 60-500 60-550 00-600 60-650 00-700 60-750 00-SOO 60-850 60-000 Kxpaimioii Iaohos p<ir 100 ft. 1-56 L-99 2-43 2-SO 3-35 3-83 4- 31 4'H1 S-31 5-83 6-38 6'SO 7-44 7-00 371. Pipe work supports.—All pipe work shall bo adequately supported in ordor to permit free movement for expansion and contraction, and the amount of such movement shall bo proportioned throughout tho wholo of any main by the provision of anchors at suitable points. Whore pipes may be subject to vortical movement, spring supports denignod to carry tho load under all conditions shall be provided. It is desirable that points of supports should, as far as practicable, be arranged adja- cent to the pipe joints. Slings aro in general preferable to roller supports, and these latter should bo used only whoro necessary. All pipe supports should, as far an practicable, be of mild stool and pipe anchors oither of mild steel or oast steel.

Previous and next

All provisions of Indian Boiler Regulations, 1950.

Questions people ask

Is regulation 835 of Indian Boiler Regulations, 1950. still in force?

No repeal of Indian Boiler Regulations, 1950. is recorded.