Regulation 18, Indian Boiler Regulations, 1950.: Testing and Inspecting
Indian Boiler Regulations, 1950. - Regulation 18
Text of regulation 18
Testing and Inspecting
18. Testing and Inspecting.—The following tests and inspections shall be made
at the place of manufacture prior to despatch ; but, in the event of any of the material
[1«12 THE 0iM5?fi3BPtfffl ffl3?SA EXTKAOBDINARY [£A»T II
proving unsatisfactory in. t,lxe opqrfie of, being worker! into boilers, suoh material
nh.aH be rejected, notwithstanding any previous certificate of satisfactory testing,
«nd suoh further tests of the material from the same charge shall bo made as the
Trtwpsiotitig1 Qffieef in- attendkhice1 may f-onsider desirable,
j ' f i | i ' i
14. Selection oi test pieces.—All ttst pieces shall bo seleotod by tho Inspecting
Offioor and tested in his presence, and he shfill satisfy himself that the conditions
'flWiii described are fulfilled. '
16. (a) Tensile test pieces.—The tensile strength and ductility shall be deter-
mined from standard test pieces (see App. "R) cut lengthwise or crosswise from tho
rolled material. When material is annoaled or otherwise treated before despatch,
tho test pieces shall be similarly and simultimeously tieatod with the material before
testing.
(b) (I) Plates, Angles and Tees.—Wherev^t practicable, the rolled surface shall
be retained on two opposite sides of tho test piece. Tho tensile stress and elongation
shall bo determined on standard test piece A (see App. B).
(ii) Bound Ban.- -Round bars may be tested fall size tm rolled or they may be
turned down to a convenient size
If tested 1 inch djamettjr or under, test piece B (see App. B) shall be used. The
sectional area of the tosi piece shall not be less than J squaro inch.
Where fhe te,a,t piece is over 1 inch diameter, test piece Bx (see App. B) may b»
usod.
Any straightening of the test pieces which may be required shall be done oold.
, J6r Tensile Testff.^-The ultimate tensile stress and elongation of the various
ojasmos qf ,ma;terials phall be between tho limits shown in the table below but a range
, of not mppo t h w 4 tons in'each olass of material shall be permitted.
Should a tensile tost piece break outside the middle half of the test gauge length
the test may be discarded and another test be made of tho same plate or bar.
1 i
J)nH(Tiption
Pluten for shells butt utrrtp^,
PltitfV) for IlanKiiip or woklinK
Flutes for fiii'iiacoH
Sttty anftlfi nnd ten bftjN
Rivot burn
Ulhnidto
toilflllo
t̂roRn
in
26—:t(l
24—.10
2(1—Ifl
11—.10
Minimum elonKotion per oeut.
Tre t̂ piono A
23 iur 2fl- 30
20 for 28 -32
20 for 3 2 - 36
23 for 2 4 ^ 3 0
20 for 28—32
23
23 for 2fi- 30
20 for 28—32
20 for 32—3fi
TOHL pinw R
23 for 26—10
20 for 28—32
20 for 32 --30
25 for 24^-2.S
23 for 26—30
Tost piHOfi f
28 for 20- -30
24 for 28- - 32
24 for 32—38
30 for 2<1—2S
28 for 20- 30
17. Number of Tensile Tests.—(a) Plates.—For sholl platca, butt straps and
gusset plates one tensile tost pieoo shall bo cut from oach end of every plato as roll-
ed.
(b) For other plates such as end plates, furnace and flanging plates etc., on«
tensile tost pieco shall bo cut from one ond of every plate as rolled.
(c) Angle, tee, rivet and stay bars.-—One tensile test shall be made from oaoh 15 or
part of 15 bars rolled of oach seotion or diameter from tho same oharge, but not lesa
than two tensile tests shall be made unloss the total number of bars rolled from tho
^arae charg-e is1 8 or less than 8 and the bars are of the same section or diameter, in
J ^hfeh! odm brie tensile teat shall suffice. For round bars of 1} inches diameter and
13H0. 8] 1. .jn WA^UWLI-EJ U.E J.JNLUA iiijl.1.
under, the numbers 50 and 20 shall be substituted for 15 and 8 respectively for
determining the numbm of tests required.
18. Dump Testa.—Short lengths equal to twine, thoir diameter out from tho
rivet bars shall, when rold, withstand -without fraoture being compressed to half
their length. A dump test shall be made for eaoh Tensile Test.
Previous and next
Questions people ask
Is regulation 18 of Indian Boiler Regulations, 1950. still in force?
No repeal of Indian Boiler Regulations, 1950. is recorded.