LawGrids logoLAWGRIDS.ORG

Rule 35, Atomic Energy (Factories) Rules, 1996: LIFTING MACHINES, CHAINS, ROPES AND LIFTING TACKLES

Atomic Energy (Factories) Rules, 1996 - Rule 35

Text of rule 35

LIFTING MACHINES, CHAINS, ROPES AND LIFTING TACKLES

35. LIFTING MACHINES, CHAINS, ROPES AND LIFTING TACKLES.- (1) No lifting machine and no chain, rope or lifting tackle, except a fibre rope or fibre rope sling, shall be taken into use in any factory for the first time in that factory unless it has been tested and all parts have been thoroughly examined by a competent person and a certificate of such a test and examination specifying the safe working load or loads and signed by the person making the test and the examination, has been obtained and is kept available for inspection. (2) Every jib-crane so constructed that the safe working load may be varied by the raising or lowering of the jib, shall have attached there to either an automatic indicator of safe working loads or an automatic jib angle indicator and a table indicating the safe working load at corresponding inclinations of the jib or corresponding radii of the load. An audio-visual alarm be preferably provided in addition, to give alarm wherever the limits given in table are exceeded. (3) A table showing the safe working loads of every kind and Atomic Energy Factory Rules, 1996 35 Rule 35 size of chain, rope or lifting tackle in use, and, in the case of a multiple sling, the safe working loads at different angles of the legs, shall be pasted in the store in which the chains, ropes or lifting tackles are kept, and in prominent positions on the premises, and no chain, rope or lifting tackle not shown in the table shall be used: Provided that this sub-rule shall not apply in respect of such lifting tackle if the safe working load thereof, or in the case of a multiple sling, the safe working load at different angles of the legs, is plainly marked upon it. (4) The register to be maintained under clause (a)(iii) of sub-section (1) of Section 29 of the Act shall contain the report as given in Form - 4, giving following particulars and shall be kept readily available for inspection:- (a) Name of occupier of factory. (b) Address of factory. (c) Distinguishing number or mark, if any, and description sufficient to identify the lifting machine, chain, rope, or the lifting tackle. (d) Date when the lifting machine, chain, rope or lifting tackle was first taken into use in the factory. (e) Date and number of the certificate relating to any test and examination made under sub-rules (1) and (15) together with the name and address of the person who issued the certificate. (f) Date of each periodical thorough examination made under clause (a) (iii) of sub- section(1) of Section 29 of the Act and sub-section (3) and by whom it was carried out. (g) Date of annealing or other heat treatment of the chain and other lifting tackle made under sub-rule (7) and by whom it was carried out. (h) Particulars of any defects affecting the safe working load found at any such thorough examination or after annealing and of the steps taken to remedy such defects. (5) All rails on which a travelling crane moves and every track on which the carriage of a transporter or runway moves shall be of proper size and adequate strength and have an even running surface; and every such rail or track shall be properly laid, adequately supported and properly maintained. Atomic Energy Factory Rules, 1996 36 Rule 35 (6) To provide access to rail tracks of overhead travelling cranes suitable passage-ways of at least 50 centimeters width with toeboards and double hand rails 90 centimeters high shall be provided alongside, and clear of, the rail tracks of overhead travelling cranes, such that no moving part of the crane can strike persons on the ways, and the passage-way shall be at a lower level than the crane track itself. Safe access ladders shall be provided at suitable intervals to afford access to these passage-ways, and from passage-ways to the rail tracks: Provided that the Competent Authority may, for reasons to be specified in writing, exempt any factory in respect of any overhead travelling crane from the operation of any provision of this sub-rule subject to such conditions as it may specify. (7) All chains and lifting tackles except a rope sling shall, unless they have been subjected to such other heat treatment as may be approved by the Competent Authority of Factories, be effectively annealed under the supervision of a competent person at the following intervals:- (a) all chains, slings, rings, hooks, shackles and swivels used in connection with molten metal or molten slag or when they are made of 12.5 millimeters bar or smaller, once at least in every six months; and (b) all other chains, rings, hooks, shackles and swivels in general use, once at least in every twelve months: Provided that chains and lifting tackle not in frequent use shall, subject to the Competent Authority's approval, be annealed only when necessary. Particulars of such annealing shall be entered in a register prescribed under sub-rule (4). (c) Slinging- (i) Chains shall not be joined by bolting or wiring links together. They shall not be shortened by tying knots. A chain in which the links are locked, stretched or do not move freely shall not be used. The chain shall be free of kinks and twists. Proper eye splices shall be used to attach the chain hooks. (ii) Pulley blocks of the proper size shall be used to allow the rope free play in the sheave grooves and to protect the wire rope from sharp bends under load. Idle sling shall not be carried on the crane hook along with a loaded sling. When idle slings are carried they shall be hooked. Atomic Energy Factory Rules, 1996 37 Rule 35 (iii) While using multileged slings, each sling or leg shall be loaded evenly and the slings shall be of sufficient length to avoid a wide angle between the legs. (iv) Sling hitches on loads shall be made under the supervision of experienced persons. (8) Nothing in the foregoing sub-rule (7) shall apply to the following classes of chains and lifting tackles, namely:- (a) chains made of malleable cast iron; (b) plate link chains; (c) chains, rings, hooks, shackles and swivels made of steel or of any non-ferrous metal; (d) pitched chains, working on sprocket or pocketed wheels; (e) rings, hooks, shackles and swivels permanently attached to pitched chains, pulley blocks or weighing machines; (f) hooks and swivels having screw threaded parts or ball bearing or other case hardened parts; (g) socket shackles secured to wire ropes by white-metal capping; and (h) bordeaux connections: Provided that such chains and lifting tackles shall be thoroughly examined by a competent person once at least in every twelve months, and particulars entered in the register kept in accordance with sub-rule (4). (9) Cranes shall be operated only by authorised persons who are well trained and experienced, operators shall ensure that all safety devices are functioning properly before crane is put into operation. (10) A mobile crane shall be operated so that none of its parts can approach live electric lines closer than 3 m. While lifting loads such a crane shall be located on level ground. (11) Standard signals shall be used and operators shall recognise signals from only one person during crane operation. Signal men shall direct equipment movement at fills, quarries, pits, intersections or any other place where necessary to prevent possible accidents. (12) No person shall be permitted to work or walk under a load. Atomic Energy Factory Rules, 1996 38 Rules 35-36 (13) Thorough inspection and load testing of a crane shall be done by a competent person at least once every 12 months. The load to be used for the purpose of testing shall be as follows: Safe working load Test load Up to 20 tons 25% in excess 20 - 50 tons 5 tons in excess Over 50 tons 10% in excess (14) All lifting machines, ropes, chains and lifting tackles, except a fibre rope or fibre sling, which have been lengthened, altered or repaired by welding or otherwise, shall, before being again taken into use, be adequately re-tested and re-examined by a competent person and certificate of such test and examination be obtained, and particulars entered in the register kept in accordance with sub-rule (4). (15) No person under 18 years of age and no person who is not sufficiently competent and reliable shall be employed as driver of a lifting machine whether driven by mechanical power or otherwise, or to give signals to a driver. (16) Where the Competent Authority is satisfied that in a factory due to shutdown or for any other reasons it is not practicable to maintain a minimum distance of 6 metres between the person employed or working on or near the wheel track of a travelling crane and the crane, it may on the request of the manager reduce the distance to such extent as it may consider necessary and also prescribe further precautions indicating appointment of suitable number of supervisors to ensure the safety of the persons while they are employed or working on or near the track.

Previous and next

All provisions of Atomic Energy (Factories) Rules, 1996

Questions people ask

Is rule 35 of Atomic Energy (Factories) Rules, 1996 still in force?

No repeal of Atomic Energy (Factories) Rules, 1996 is recorded.