Form 39, The kerala Inland Vessels Rules, 2015: FORM No. 39
The kerala Inland Vessels Rules, 2015 - Form 39
Text of form 39
FORM No. 39
FORM No. 39
[See Rule 54 10)]
ROUTE PERMIT
This is to certify that I.......................the Competent Authority have
issued..............(type of permit) to...................(vessel name) having registration
number. .................. on .................
Particulars of vessel
I Name of the owner
of the vessel
2 Address
3 Name of the vessel Owner/Operator/Others (Specify)
4 Type of vessel
5 Registration Number House boat/Passenger vessel!
Speed boat with 013 engine/
Cargo vessel/Dredgers/Others
6 Certificate of Survey
number
7 Date of expiry of validity
of certificate of survey
8 No. of clew assigned
to the vessel
9 Name and place of
Assigned Jetty
10
-
Name and place of
Mooring Point
II Type of Route
Permit _________________________________ 12
Route details
Stag point End point
13 No. of trips required
- ---s -:— ; -
33
14 Trip details (Applicable Departhre Time Arrival Time
only for Passenger
Service route permit)
15 Details of -Insurance
Policy
16 Validity period of Route
Permit 2 years
Port of Registry Name of Competent Authority:
Date of Issue: Signature:
(44) after Annexure IV, the following Annexure shall be added,
namely:— -
ANNEXURE-v
L (a) Procedure for conducting Heel test
The vessel shall be subjected heel test where applicable as per
requirements of rule 134 (6) (a). A total heeling moment of WB/12 shall be
imposed on freely floating vessel by shifting known weights through known
distance, where
W=weight of all persons on board including passengers and crew
@ 75 kgs. per persons.
B'=extreme breadth (m) of the vessel to the outside of hull plating,
excluding any fendering or rubbing strakes.
A step-by-step procedure for conducting the test is given below.
(b) Preparation of the vessel for Heel test
The vessel shall be complete in all respects and freely floating
without grounding.
All extraneous items that-do not belong to the vessel - shall be
removed except those items or equipment required on board for
conducting the heel test. -
33/1370/2015/S-3. - . -
34
All tanks meant for storage of liquids shall be kept 95% full.
Two independent devicesfor measuring the angle of inclination of
the vessel shall be provided. These can consist of pendulum,
calibrated inclinometer, water-tube or pre-marked battens, including
a combination of 2 different devices.
5: Persopson board for conducting the test shall be assigned
positions on the centre line of the vessel and these positions shall
be marked on deck with a suitable marker. All persons on board
shall stand at their assigned positions while the readings of the
angle of inclination are taken. I
Measure the extreme breadth of the ship to the outside of the hull
plating, excluding any fendering or rubbing strakes.
Measure and record density of water by hydrometer or any other
means.
S. The total weight W to be placed on board including person/s on
board conducting the test shall be calculated as follows:
W = 75xN kg.
where N is the total number of persaiis the vessel is intended to
carry, including passengers and crew.
The weights to be placed on board excluding persons is then givel
by W1 = W—Wp.
where Wp is the weight of person/s on board conducting the test.
9. Arrange the weights in batches on port and starboard sides
symmetrically with .respect to the centerline of the vessel. Ensure
- that the vertical centre of gravity (VCG) above the decklplatforrn of
each batch of weights is same as the assumed VCG of standing or
seated passengers. Mark the position of each batch of weights.
Weights to be shifted shall consist of 2 batches on each side
(2 port & 2 stbd.) and shall be marked W and W 2.
Determine the distances d, and d2 through which weights W 4id
will be shifted: .
Total heeling moment to be applied to one side = W.BI
W51.d1+ w. d2 -
Weight shifted during first shift = W 1 (kg)
35 •
Distance through which W51 is shifted = d1
Heeling moment due to first shift = W 1 . d1
Total heeling moment to be applied = W.13/12
Heeling Moment to be applied in second shift = W.B/12 - W 1 . d1
Weigh't shifted in second shiftW52
Distance through W52 which is to be shifted, d2=(W.B/12_W 1 dj/W52
(c) Heel test
12. Take readings of pendulum/inclinometer/water tube as provided in
the upright condition.
Shift first weight .W 1 transversely through the calculated distance d1.
Take readings of pendulunilinclinometer/viater tube.
Shift second weight W 2 in the same direction through the
calculated distance d2. Now bothW1 and W52 are on the other side
and the required total heeling moment=W.8/12 has been applied.
Take readings of pendulum/inclinometer/water tube. At this stage
check to see whether the avenge angle of inclination exceeds 70
(a) If the angle of inclination exceeds 70, the number of
passengers the vessel is intendend to carry can he reduced in
consultation with the owner and the test restarted from step 8.
- (b) If the average angle of inclinition does not exceed 70, proceed
to step 17.
Shift first weight W 1 back to its initial position.
Take readings of pendulum/inclinometer/water tube.
Shift second weight W32 backtó its initial position. Now the vessel
is back in the original upright condition.
Take readings of pendulum/inclinometer/water tube.
Repeat steps 13 through 20, shifting similar weights in the
opposite direction.
The boat passes the heel test if the mean total angle of inclination
to any side corresponding to the applied heeling moment of WB/l2
does not exceed 70
36
(d) Precautions
The vessel shall be freely, floating without grounding and free from
all restrains when readings are taken. Mooring ropes shall be kept
slack when readings are taken. -
The testshall be conducted in calm weather with no significant wind,
waves of current.
Only person/s essential for conducting the test shall be permitted on
board during the test and shall wear life jacket/s. Such person/s shall
stand still at their assigned positions when readings are taken.
If at any stage of the test; the vessel is found to heel dangerously,
the test shall be stopped immediately.
Sounding shall be taken and recorded for all tanks.
H. Heel Test Standard
Condition of Vessel
The heeling test shall be conducted in fully loaded condition with passenger
and crew substituted by equivalent weight having the same assumed vertical
centre of gravity as given in section 3 (1). During heel test fuel and water tanks
95% full. Any ballast present on the vessel, shall be recorded for reference at
future stñbility verifications. Photographs of the vessel should be taken to aid
recording of the condition of the vessel during the test. The heeltest should be
conducted in fresh water, the density of the water shall be measured using a
hydrometer and recorded.
Weights
Any form of weights may be used where the mass is known or can be I
checked using a suitable weighing device. Care shall be taken when using
sandbags or similai where moisture ingress may have a significant effect on their /
weight. The use of people for perfonriing heeling tests is not permitted due to/
safety and accuracy considerations.
37
(e) Movement of weights
The total heeling moment of WB/12 shall be imposed in 2 shifts of
approximately WB/24, with the angle of heel being recorded at each stage. This
staged heeling allows for subsequent analysis in borderline cases, helps avoid
experimental errors and reduces the risk of excessive, heel angles being achieved
on newly considered vessels'The process shall be performed for shifts both to
port and to starboard. It is not necessary to utilise all the weights on board to
produce the required heeling moment; the amount of weight used to provide the
heeling moment will depend upon the distance it is able to be shifted. The type
of weights, distribution and movement shall be agreed with the owner or
representative prior to the test.
Measurement of Angle of Heel
The Angle of heel may bei measured using battens pre-marked with
freeboard corresponding to 5° and 7° of heel. In most cases, however, it is
considered easier to calculate the angle of heel by 'use of a pendulum, calibrated
inclinometer, water tube or by freeboard measurements. The angles of heel shall
be measured by two separate methods where practicable to provide a means of
verification. For example, this could be two pendulums (forward and aft), a
pendulum and freeboard measurements or pendulum and inclinometer. When a
penduluth is used to measure the heel angle the pendulum shall ideally be of
sufficient length to produce a deflection of 35 nun for each weight shift. The
angle of heel shall be recorded in the spaces provided on the proforma. Care
shall be taken to ensure the vessel is floating freely and avoid the influence of
wash from passing vessels, wind heeling and mooring line tension on heel angle
measurements.
Assumed Disposition of Passenger Loading
Passenger numbers are allocated on a basis of 0.36m' per passenger for
the clear deck area. Clear deck area excludes any permailent fixtures that reduce
the deck area available to standing passengers. Where permanently fitted seating
is present, the area taken up by the seating is. subtracted from the clear deck
area, and the number of seats added to the passenger allocation for that deck. If
the seating is in the form of benches, the number of passengers is to be
calculated by dividing the length of the bench in mm by 460 and rounding to the
nearest integer passenger value. However, the total passenger allocation shall not
exceed that permitted by Registering Authority.
FE]
Q7 Assumed Centre of Gravity of Passengers
The vertical centre of gravity of standing passengers shall be asumed to be
760 mm above the deck on which they are standing. VCG of the seated
passengers shall be assumed to be 300 mm above the seat base. During the heel
test, equivalent weight shall be substituted for passengers such that the VCG of
the weights shall confirm to the assumed VCG of the passengers as detailed
above. -
(g) Passenger Heeling Moment
The two thirds-one third passenger distribution equates to the standard
passenger heeling moment of WB/12. w is the weight of passengers (@ 75 kg.
each) and B is the extreme breadth to the outside of the hull plating (excluding
any fendering or rubbing snakes). This heeling moment may be applied usink any
weight and shift distance combination, provided it produces the required heeling
moment (heeling moment = weight x distance moved).
ifi. Classification of water bodies and intact stability requirements
The intact stability requirements are dependent on the area of operation, the
number of passengers onboard and the number of decks. Table A.l below
indicates which requirements apply to each water category and vessel type.
Table A. 1—Applicable Standards
Wa16
category
Maximum Number
of passengers
Number of
Decks
Applicable
Standards
(1) (2) (3) (4)
IWA <=50 Oor I Heel Test
JWA <=50 >1 Righting Lever
Criteria
IWA >50 Any Righting Lever
Criteria
IWS <=50 0 or I Heel Test
S
(1) (2) (3) (4)
rWB c50 >1 Righting kQer
- Criteria
IWO >50 >1 Righting Lever
Criteria
IWC Any >l Righting Lever
Criteria, Heel
on Turn, SWRC
IWD Any >=l - Righting Lever
Criteria, Heel on
Turn, SWRC
Notes:—
In the "Decks" column in the above table, "0" means a vessel which
is completely open, "l",means a partially or fully decked vessel.
Category "IWA" means narrow rivers and canals where the depth of
water is generally less than 1.5 metres. -
Category "IWO" means wider rivers and canals where the depth of
water is generally 1.5 metres or more and where the significant wave
- height could not be expected to exceed 0.6 metres at any time.
Category "IWC" means tidal rivers and estuaries and large, deep lakes
where the significant wave height could not be expected to exceed
1.2 metres at any time.
Category "IWD" means tidal rivers and estuaries where the
significant wave height could not be expected to exceed 2.0 metres at
any time. In the "Decks" column in the above table, "0" means a
vessel which is completely open, as depicted in Annex 7. "I" means
a partially or fully decked vessel.
40
IV. Righting Lever Criteria
The area under the righting lever curve (GZ curve) shall not be less than
0.055 metre-radians up to ç = 300 angle of heel and not less than 0.09
metre- radians' up to p = 400 or the angle of down-flooding p if
this angle is less than 40°. Additionally, the area under the righting lever
curve (GZ curve) between the angleá of heel of 30° and 400 or between
30°and 91 if this angle is less than- 40° shall not be less than 0.03
metre-radian.
The righting lever GZ shall be at least 0.20 rn at an angle of heel equal
to or greater than 30°.
The maximum righting lever shall occur at an angle of heel not less
than 30°. This angle may be permitted to be reduced to 250 having
regard to the design of a particular vessel.
The following shall be applied where a vessel's characteristics render
compliance with .the criterion ofA4.(1) to (3) impracticable:
The area under the curve of righting levers (GZ curve) shall not be
less than 0.070 metre-radians up to an angle of 15° when the maximum
righting lever (GZ) occurs at 15° and 0.055 metre-radians up to an
angle of 30° when the maximum righting lever (GZ) occurs at 30° or
above. Where the maximum righting lever (GZ) occurs at angles of
between 15° and 30°, the corresponding area under the righting lever
curve shall be:
0.055 + 0.001 (300- p) metre-radians'
The initial meta-centric height GM0 shall, not be less than 0.15m.
The angle of heel on account of crowding of passengers to one side as
defined below shall not exceed 10°
Note:—l. p1 is an angle of heel at which openingsin the hull, superstructures
or deckhouses which cannot be closed weather tight immerse.
in aj,plying this criterion, small openings through which
progressive flooding cannot take place need not be considered
as open.
Note:-2. p,,,, is the angle of heel in degrees at which the righting lever curve
reaches its maximum.
UI
Heel on Turn Criterion
the angle of heel on account of turning shall not exceed 100 when
calculated using the following formula:
M4=0.2
- where:
MA = heeling moment (kNm)
V0 = service speed (mis)
LWL = length of vessel at waterline (m)
A = displacement (t)
d = mean draught (m)
KG = tieight of centre of gravity above baseline (m)
Severe Wind and Rolling Criterion (Weather Criterion)
(1) The ability of a vessel to withstand the combined effects of
beam wind and rolling shall be demonstrated, with reference to
the figure A. I as follows:
-
(a) the vessel is subjected to a steady wind pressure acting.
perpendicular to the vessel's centreline which results in a
steady wind heeling lever (11).
33/1370/201 5/s-2o:
42
from the Iesultant angle of equilibriuth (p), the vessel is
assumed to roll owing to wave action to an angle of roll
(91) to windward. The angle of heel under action of steady
wind ((p0 ) shall not exceed 16° or 80% of the angle of
deck edge immersion, whichever is less.
the vessel is then subjected to a gust wind pressure which
results in a gust wind heeling lever (12); -
d) under these circumstances, area b shall be equal to or
greater than area a
The angles in the above figure A. I are defined as follows:
p0 = angle of heel under action of steady wind
p1 =. angle of roll to windward due to wave action (The
angle of roll for vessels with anti-rolling devices should be
determined without taking into account the operation of
these devices unless the authority is satisfied with the proof
that, the devices are effective even with sudden shutdown of
their supplied power.)
(p2 = angle of down-flooding ((Pr) or 500 or p, whichever
is less
where
(p1 = angle of heel at which openings in the hull,
superstructures or deckhouses which cannot be closed
weather tight immese. In applying this criterion, small
openings through which progressive flooding cannot take
place need not be considered as open.
= angle of second intercept between wind heeling lever
'w2 and GZ curve.
(2) The wind heeling levers 1, and 1.2 referred to in A.6.(l) are
constant values'at all angles of inclination and shall be calculated
as follows:
PAZ
1= (in)
i000g A
1=1.5 1,(m)
43
where:
P = wind pressure of 168 Pa (N/rn2);
A = projected lateral area of the portion of the vessel and
deck cargo above the waterline (m2);
Z = vertical distance from the centre of Am the centie of
the underwater lateral area or approximately to a point
at one half the mean draught (m);
A = displacement (t);
g = gravitational acceleration of 9.81 rn/s2.
Alternative means for determining the wind heeling levei (1w)
may be acdepted, to the satisfaction the authority, as an
equivalent to calculation in A.6.(2). Here the wind velocity used
in the tests shall be IS m/s in full scale with uniform velocity
profile. -
The angle of roll ((p1) referred to in A.6.(l) shall be calculated
as follows: -
4)1 =l09kXX2-4Th
Where: -
-- X, X2 are factors obtained from Tables A.2 and A.3
respectively. -
k is a factor defined as follows:
k = 1.0 for round-bilged vessel -having no bilge or bar
keels -
k = 0.7 for a vessel having sharp bilges (See nOte below)
k = as shown in Table A.! for a vessel having bilge keels a
bar keel or both, where
= length of the vessel at waterline (m) -
B = moulded breadth of the vessel (m)
A1 = total overall area of bilge keels, or area of
the lateral projection of the bar keel, or sum of
these areas (in').
4
ME
Note:—"Sharp bilge" shall be oonàidered a bilge radius < 0.018 and an angle
between piecewise lines representing the bilge smaller than 120
degrees.
ris a factor given by
r = 0.73 + 0.606/d
where:
OG = KG-d
d = mean. moulded draught of the vessel (m)
s is a factor as shown in table A. 4 as a function of T, the 'essel's
natural roll period. In the absence of sufficient information, the
following approximate formula can be used to calculate T
2CB
Where:
B
C = 0.373 + 0.023 - 0.043 100
GM = metacentric height corrected for free surface
effect (m).
Table A.2—Values of factor k
(A1 x 100)/(LWL x B)
0 1.0
1.0 0.98
1.5 . . 0:95
2.0 0.89
2.5 0.79
3.0 0.74
3.5 0.72
~4.0 0.70
A1 = total overall area of bilge keels, or area of the lateral
projection of the bar keel, or sum of these areas (m').
.45
Table AS-Values of factor X,
Bids
(
:52.4 1.0
2.5 0.9$
2.6 0.96
2.7 0.95
2.8 0.93
2.9 0.91
3.0 0.90
3.1 0.88
3.2 0.86
3.4 . 0.82
- r
H 3.5 0.80
3.6 0.79
4.0 0.78
4.5 0.76
5.0 0.72
5.5 0.68
6.0 :
- 0.64
6.5 0.62
*B is the breadth of the vessel and dis the draft.
..
. 46 -
Table A.4—Values of factor X2
CB S I 24
~ 0.45 . . 0.75
-. 0.50 0.82
0.55 0.89
0.60 0.95
0.65 0.97
2:0.70 ..
*
1.00
C. is the block coefficient of the vessel
Table A.5—Values of factOr s
TO
3.5 0.100
4.0 0.099
4.5 . 0.096
.5.0 0.090
7.0 0.064
9.0 0.042
9.5 - - 0.038
10.0 - 0.037
10.5 0.035
* To is the natural roll period of the vessel.
47
VII. Standard Loading Conditions
Wherever applicable, Righting Lever Criteria, I-/eel on Turn
Criterion and Severe Wind and Rolling Criterion shall be applied
to the following loading conditions:
Vessels with I deck only
(I) Light ship
(2) Fully loaded departure with all persons standing pn one side
I
(3) Fully loaded arrival with all persons standing on one side.
Vessels with 2 decks
Light ship
Fully loaded departure with all persons standing
Fully loaded arrival with all persons standing
Partially loaded departure with passengers on upper deck
only at the rated capacity of upper deck, all persons
standing.
Partially loaded arrival with passengers on upper deck
only at the rated capacity of upper deck, all persons
standing.
Note:—Additional loading conditions can be specified by the authority when it
is deemed that such conditions are critical with regard to the intact
stability of the vessel.
Weight and Centre of Gravity of Passengers and Crew.
The weight of a person shall be taken as 75 kgs. The vertical centre of
gravity of i standing person shall be taken as I or above the deck on
which the person is standing and that of a seated person shall be taken as
0.5rn above the deck on which the person is seated.".
By order of the Governor,
. - V. J. KURIAN,
Additional Chief Secretary to Government.
EEl
I
Explanatory Note
(This does not form part of the notification, but is intended to indicate its
general purport.)
As per notification issued under G. 0. (P) No. 5/2010ICSIND, dated 30th
April, 2010 and published as S.R.O. No. 424/2010 in the Kerala Gazette
Extraordinary No. 1055 dated 30th April, 2010 Government have issued the
Kerãla Inland Vessels Rules, 2010. Vide G. 0. (Rt.) 'Not 1293/2013/Tourism, . F
dated 15th February, 2013 a nine member Committee was constituted for
making recommendations to Government of Kerala to foster backwater tourism F
without compromising on safety, efficiency and pollution aspects through a
consultative process. Based on the report of the Committee, Government have
decided to amend the Kerala Inland Vessels Rules, 2010 by incorporating
provisions for safety, security, pollution control and quality serVice.
This notification is intended to achieve the above object.
Previous and next
Questions people ask
Is form 39 of the kerala Inland Vessels Rules, 2015 still in force?
No repeal of the kerala Inland Vessels Rules, 2015 is recorded.