LawGrids logoLAWGRIDS.ORG

Rule 27, Tripura Factories Rules, 2007: Exemption

Tripura Factories Rules, 2007 - Rule 27

Text of rule 27

Exemption

27. Exemption: - If in respect of any factory the Chief Inspector is satisfied that (owing to the exceptional circumstances or infrequency of the process or for any other reason) all or any of the provisions of this Schedule are not necessary for the protection of persons employed in the factory, he may by certificate in writing exempt such factory from all or any of such provisions subject to such conditions 208 as he may specify therein. Such certificates may at any time be revoked by the Chief Inspector. Appendix “A” (See paragraphs 2, 10, 13 and 15) The benzenes, toluenes, xylenes, having undergone nitration once or several times (nitrodininitro and trinitro benzene and its homologues) and their chlorinated compounds, naphthalenes, having undergone nitration once or several times, aniline and its homologues (toludine, xylidine, cumidine), anisidine, phenetidine, and their chlorinated, nitrated and alkylated compounds (dimethylanilin, toluydendiamine, phynylhydrazine, toluylhydrazine). Appendix ‘C’ (See paragraph 3) Cautionary placard Advice to workers: - 1. Nitro and amino compounds or aromatic hydrocarbons are dangerous. In this factory you have to handle them frequently. 2. All items of protective wear provided should be made use of to safeguard your health. 3. Maintain scrupulous cleanliness at all times. Before meal wash hands and feet. A bath before leaving the factory is essential, taking care to wash the head well. 4. If any chemical fails on your body, wash it off immediately with soap and water. Change clothing at once, if (soiled) with a cyanotic nitro or amino compound. Contact the appointed doctor immediately. 5. Do not handle any nitro or amino compound with bare hands. Use a long-handled scoop. 6. Avoid alcoholic drinks as these increase risk of poisoning. 7. In case of illness contact the Factory Manager and the appointed doctor. 8. Do not chew, eat, drink or smoke or smoke in the work-room or with soiled hands. Keep food and drink away from the work-place. 9. If you work with betanapthylamine or benzidine or its salts, alphanaphthylamine or (dianisidine). a) remember that serious effects will follow after a number of years if great care is not taken to observe absolute cleanliness of body clothes, machinery and tools. b) at meal time, wash face and hands twice with soap and water to remove all chemicals, wear a long sleeved clean apron while eating; c) before leaving the factory take a bath using soap and water twice; after this put on your home clothes. Schedule XII Handling and manipulation of corrosive substances. 1. Definition: - For the purposes of this Schedule: - a) “corrosive substance” includes sulphuric acid, nitric acid, hydrochloric acid, hydrofluoric acid, carbonic acid, phosphoric acid, liquid chlorine, liquid chlorine, liquid bromine, ammonia or mixtures thereof or any other substance which the State Government may, by notification in the Official Gazette, specify to corrosive substance. b) “corrosive operation” means an operation of manufacturing, storing, handling, processing, packing or using any corrosive substance in factory; 2) Flooring: -The floor of every work-room of a factory to which this Schedule applies, shall be made of impervious, corrosion and fire resistant material and 209 shall be so constructed as to prevent collection of any corrosive substances. The surface or such flooring shall be smooth and cleaned as often as necessary and maintained in a sound condition. 3) Protective equipment: - a) The occupier shall provide maintain in a good order and keep in a clean condition for the use of all persons employed in any corrosive operation, suitable protective wear for hands and feet, suitable aprons, face shields, chemical safety goggles and suitable respirators. b) The protective equipment provided shall be used by every person engaged in doing any corrosive operation. 4. Water facilities: - Where any corrosive operation is carried on, there shall be provided as close to the place of such operation as possible, a source of water at a height of 2 meters secured from a pipe of 25 mms. diameter fitted with a quick acting value, or safety tank having dimensions not less than 200cms in length129cms. in breadth and 60sms. in depth full of clean water placed at the floor level or such dimension as are approved by the Chief Inspector of Factories, so that in case of injury to the worker by any corrosive substances, the injured part can be thoroughly flooded with water. 5. Cautionary notice: - A cautionary notice in the following form printed in the language which the majority of the workers employed in the factory understand shall be affixed prominently close to the place where any of the corrosive operations is carried out and where it can be easily and conveniently read by the workers. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so affixed: - Cautionary Notice Danger Corrosive substances cause service burns and vapours thereof may be extremely hazardous. Use protective wear. I case of contact, immediately flood the part affected with plenty of water for at least 15 minutes. Get medical attention quickly. 6. Transport:- a) Corrosive substances shall not be filled, moved or carried except in containers, and when they are to be transported, the containers shall be included in crates of sound construction and of sufficient strength. b) Containers having a capacity of 10 or more litres of a corrosive substance shall be placed in a receptacle or crate and then carried by more than one person at a height below the waistline unless a suitable rubber wheeled truck is used for the purpose. c) Containers for corrosive substances shall be clearly labelled as such. 7. Devices for handling corrosive substances: - a) Suitable tilting or lifting device shall be used for employing jars or carboys and other containers of corrosive substances. b) Corrosive substances shall not be handled by bare hands but by means of a suitable scoop. 210 8. Opening of valves: - Valves fitted to containers holding a corrosive substance which do not work freely shall not be forced open. They shall be opened by a worker suitably trained for the purpose. 8. A) Prevention of splashing of corrosive substance leaking: - All flange joints on line s carrying corrosive substance under pressure shall be provided with guards to prevent splashing of corrosive substance leaking through the joints due to gasket failures on workers working nearby. 9. Cleaning tanks, stills, etc: - a) In cleaning out or removing residues from stills or other large chambers used for holding corrosive substances, wooden implements shall be used to prevent production of arseniuretted hydrogen (Arsine) b) Whenever it is necessary for any worker to enter confined spaces, like chambers or tanks which were used to stock corrosive substances, while for the purpose of cleaning or other maintenance shall be taken to ensure the worker’s safety. c) Before repairs are undertaken to any part of equipment in which a corrosive substance was handled, such equipment or part thereof shall be freed of any adhering corrosive substance by adopting suitable methods. 10. Storage: - a) Corrosive substances shall not be stored in the same room with other chemicals which are likely to violently react with them or give rise to poisonous fumes or gases after an accidental mixing, e.g. turpentine, carbides, metallic powders, combustible materials and cyanide salts. b) Pumping or filling overhead tanks, receptacles, vats and other containers shall be so arranged that there is no possibility of any corrosive substance overflowing and causing injury to any person. c) Every container having a storage capacity of twenty litres or more pipe lines, valves and fitting used for storing or carrying corrosive substances shall be examined thoroughly every year for finding out any defect and the defects shall be removed forthwith. A register shall be maintained of every such examination made and it shall be produced before the Inspector, whenever required. 11. Fire extinguishers: - An adequate number of suitable types of fire extinguishers or other fire-fighting equipments, depending on the nature of the chemicals stored in any place in a factory, shall be placed near each such place and such fire-extinguishers or other fire-fighting equipments shall be regularly tested and refilled. Clear instructions as to how the extinguishers or other equipments should be used, printed in the language which the majority of the workers employed in such factory understand, shall be affixed near each extinguisher or other equipment. Sufficient number of workers shall be trained in fire-fighting practices. 12. Exemption: - If in respect of any factory on an application made by the manager, the Chief Inspector is satisfied that owing to the exceptional circumstances or the infrequency of the process or for any other reason to be recorded in writing all or any of the provisions of this Schedule are not to necessary for the protection of the persons employed in such factory, he may by a certificate in writing exempt such factory from all or any of the provisions indicated in such certificate on such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector. 211 Schedule XIII Manufacturing of bangles and other articles from cinematograph film and toxic inflammable solvents 1. Definition: - For the purpose of this Schedule: - a) toxic and inflammable solvents mean: - i) solvents like acetone, tetrachlorethane, alcohol, denatured sprit, phenol, amylacitate, butyle acetate, diacetone, alcohol and such other substances which in the opinion of the Chief Inspector are toxic and inflammable; ii) “bangle polish” and “bangle mixture” and such other solvents by whatever trade name they are known, used in the manufacture of bangles and other articles from cellulose films; b) “suspension” means suspension from employment in any process in which toxic and inflammable solvents are used, by written certificates in the Health Register signed by the Certifying Surgeon, who shall have the power of suspension as regards all persons employed in any such process; c) “approval” means approved by the Chief Inspector. d) “first employment” means first employment in any process referred to in this Schedule and also re-employment in such manufacturing process following any cessation of employment for a continuous period of three calendar months. 2. Application: - This Schedule shall apply in respect of all factories or any part thereof in which the process of manufacture of bangles and other articles from cinematograph film or from toxic and said manufacturing process) is carried on. 3. Prohibition relating to employment of women and young persons: - No women or young persons shall be employed or permitted to work out or in any room in which toxic or inflammable substances or both are stored or treated. 4. Medical examination: - 1) No person shall be employed in any of the said manufacturing processes unless he has been examined by ht Certifying Surgeon within seven days preceding his first employment and certified fit for such employment. 2) No person shall be employed in any of the said manufacturing processes unless he is re-examined by the Certifying Surgeon at least once during each calendar month or at such intervals as may be specified in writing by the Chief Inspector. 3) The Certifying Surgeon shall examine persons employed in any of the said manufacturing process by giving due notice to all concerned. 4) No person after suspension shall be employed without written sanction from the Certifying surgeon entered in or attached to the Health Register. 5) No person after suspension shall be employed without written sanction from the Certifying surgeon entered in or attached to the Health Register. 5. Protective clothing: - Protective clothing shall be provided and maintained in good repair for all workers employed in the factory and such clothing shall be worn by the workers concerned. The protective clothing shall consist of a suitable apron and if so required by the Chief Inspector a head covering provided in that behalf. The head coverings so provided shall be washed daily. 6. Ventilation: - Every workroom in which cinematograph film or toxic and inflammable solvents or both are handled or manipulated or used shall be 212 provided with inlets and outlets of adequate size so as to secure and maintain efficient ventilation in all parts of the room during working hours. Provident that the preparation of “cylinders” from cinematograph film and toxic and inflammable solvents, cutting of such cylinders into bangles and heat treatment of the bangles shall be carried out in an open space under cover, unless specially exempted by the Chief Inspector. 7. Drying of cinematograph film: - 1) Drying of cinematograph film shall not be except under such conditions as will prevent the cinematograph film from coming into contact or proximity with any source of heat or heated surface in such a manner as would render the cinematograph film liable to be ignited or decomposed. 2) Loose unwound cinematograph film shall be enclosed during drying in such a manner that a person in a room will be protected as far as practicable from an outburst of flame. 3) The temperature in any part of drying enclosure for loose unwound cinematograph film other than a safety acetate film shall not at any time exceed 110oF. A thermometer shall be kept available in every room in which such drying is done. 4) Boiling of raw film either alone or in conjunction with other chemicals or heating of bangles and other articles made of film shall be carried out in an open space. 5) A sufficient number of buckets filled with water shall be provided near the places where bangles are subjected to heat treatment. 8. Storage of raw materials: - i) Each roll or package of cinematograph film used in any of the said manufacturing process, shall except when required to be exposed for the purposes of the work carried on, be kept in a separate box, properly closed and constructed of metal or other approved metal. ii) Without prejudice to the Cinematograph Film Rules, 1948, municipal rules and other rules in force, all cinematograph films not being actually used or manipulated shall be kept in a room or camber or similar enclosure approved by the Chief Inspector. Toxic and inflammable solvents stock shall be stored in approved place or containers 9. Disposal of waste films: - i) All waste and scrap of cinematograph film shall be collected at frequent intervals during each day and be placed in strong metal receptacles fitted with self-closing lids and clearly marked with words, “Film Waste”. ii) No material liable to ignite spontaneously nor anything likely to ignite or decompose cinematograph film shall be placed in the receptacle. iii) At the end of each day’s work waste and scrap films shall be either transferred to a store-room or removed from the premises. iv) Waste films and shavings shall be destroyed by burning in an open place under controlled conditions. They shall not be allowed to be thrown or scattered in or about the premises of the factory. 10. Prohibition of smoking: - i) No person shall be allowed to smoke in any room in which cinematography film is manipulated, stored or used. 213 ii) No open fire or light or any smoking materials or matches nor anything likely to ignite or decompose cinematograph film shall or toxic inflammable solvents or both are stored, manipulated or used. Provided that Chief Inspector may permit the use of coal sigree in the heat treatment of bangles subject to such conditions as he may specify in writing. 11. Caution with regard to electrical installation: - All electrical installations and fittings shall be of flame-proof type. 12. Floor of work-rooms: - The floor of every work-room in which any of the said manufacturing process are carried on shall be: - a) of cement or similar material so as to be smooth and impervious to water. b) maintained in sound condition; c) kept free from materials, plant or other obstruction not required for, or produced in, the purpose carried on in the room. d) cleaned daily after being thoroughly sprayed with water at a time when no other work is being carried on in the room. 13. Time to be allowed for washing: - Before meal and before the end of the day’s work at least ten minutes in addition to the regular meal times shall be allowed for washing to washing to each person who has been employed in any of the said manufacturing process. 14. Washing facilities: - There shall be provided and maintained in a cleanly state and in good repair for the use of all persons, a wash place under cover, with either: - i) a trough with a smooth impervious surface fitted with a waste pipe without plug and of sufficient length to allow of at least 60 centimetres for every five such persons employed at one time and having a constant supply of water from taps of jets above the trough at intervals of not more than 60cm. or ii) At least one wash basin for every five such persons employed at any one time fitted with a waste pipe and plug and having a constant supply of water laid on; and iii) a sufficient supply of clean towels made of suitable material which shall be renowed daily, which supply if so required by the Inspector, shall include a separate marked towel for each such worker; and iv) a sufficient supply of soap or other suitable cleansing material and of nail brushes. 15. Facilities for bathing: - The Chief Inspector may require any factory occupier to provide sufficient bath accommodation for all persons engaged in all or in any of the said manufacturing processes and also sufficient supply of soap and clean towels. 16. Cloak-room: - If the Chief Inspector so requires, there shall be provided and maintained for use of persons employed in any of the said manufacturing process: - a) a cloak room for clothing put off during working hours with adequate arrangement for drying the clothing, if wet; b) separate and suitable arrangements for the storage or protective clothing provided under paragraph 5. 214 17. Food, drinks, etc. prohibited in work-rooms: - No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any work-room in which any of the said manufacturing process is carried on. 18. Mess-room: - If the Chief Inspector so requires, there shall be provided and maintained for the use of all persons employed in the factory and remaining of the premises during the meal intervals, a suitable mess-room which shall be furnished with: - a) sufficient tables and benches; b) adequate means for warming food. The mess shall be placed under the charge of a responsible person and shall be kept clean. 19. Fire-fighting appliances: - 1) Adequate mean of extinguishing fires having regard to the amount of celluloid present in the room at any one time shall be kept constantly provided for each work-room and store-room. 2) The fire-fighting appliances shall be maintained in good condition and kept in a position which is easily accessible. 20. Means of escape in case of fire: - Adequate means of escape in case of fire shall be provided in every room in which cinematograph film is manipulated, used or stored and the means of escape shall not be deemed adequate unless - a) at least two separate exists are provided from every such room and two safe ways of escape from the building are available for all persons employed in the factory, and b) all doors and windows provided in connection with the means of escape are constructed to open outwards readily. 21. Cautionary notices: - i) Cautionary notices explaining the dangers to which workers are exposed due to any of the said manufacturing processes being carried on shall be affixed in prominent positions in the factory where they may be easily and conveniently read by the persons employed. The said notice shall be printed in the languages understood by the majority of workers employed in the factory. ii) If any person employed in the factory is illiterate effective steps shall be taken to explain carefully to such illiterate persons the contents of the notices. 22. Exemption: - If in respect of any factory the chief Inspector is satisfied that owing to exceptional circumstances or infrequency of the process or for any other reason, all or any of the provisions of this schedule are not necessary for the protection of the persons this employed in the factory, he may by a certificate in writing exempt such factory from all or any of the provisions on such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector without assigning any reasons. Schedule XIV Processes involving manufacture, use or evolution or carbon disulphide and hydrogen sulphide 1. Definitions: - For the purposes of this Schedule – 215 a) i) “breathing apparatus” means a helmet or face piece with necessary connections by means of which the person using it in a poisonous, asphyxiating or irritant atmosphere breathes ordinary air; ii) any other suitable apparatus approved in writing by the Chief Inspector. b) “churn” means the vessel in which the prepared cellulose pulp is treated with carbon disulphide; c) “dumping” means the drawing off molten sulphur from the sulphur posts in the process of manufacture of carbon disulphide; d) “efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gas or vapour, so as to prevent it as far as practicable from escaping into the air of any occupied room. No draught shall be deemed to be efficient if it fails to remove smoke generated at the point where such gas or vapour originates; e) “fume process” means any process in which carbon disulphide or hydrogen sulphide is produced, used or given off. f) “life belt” means a belt made of leather or other suitable material which can be securely fastened round the body with a suitable length of rope attached to it each of which is sufficiently strong to sustain the weight of a man. g) “suspension” means suspension from employment in any fume process by written certificate in the health register in Form 29 signed by the Certifying Surgeon, who shall have power of suspension as regards all persons employed in any such process. 2. Prohibition relating to employment women and young persons: - No women or young person shall be employed or permitted to work in any fume process or in any room in which any process is carried on. 3. Efficient exhaust draught and supply of fresh air: - 1) No churn shall be opened unless it has been previously subjected to an efficient exhaust draught so that when the churn is opened the concentration of carbon disulphide in the working room does not exceed 20 parts per million and no worker shall be allowed to introduce his head inside the churn or enter it unless the concentration of carbon disulphide fumes inside the churn is 20 parts per million or less, and unless the exhaust draught arrangement is continued so as to reduce the concentration of carbon disulphide to 20 parts per million or less so long as the worker or his head is inside the churn. 2) Hydrogen sulphide or carbon disulphide evolved in any room where any fume process is carried on shall be removed by an efficient exhaust draught. 3) When the ventilation apparatus normally required in connection with the process referred to in clause (2) is ineffective or is stopped for any purpose whatever work in the said room which is not he carried on and the worker shall be made to leave the leave the room as soon as possible but any case not later than 15 minutes after such an occurrence. Provided that any person wearing a breathing apparatus may be allowed to remain in the said work-room. Explanation: - The Chief Inspector may determine what constitutes normal ventilation apparatus in any given case on the representation duly made by the manager. 216 4) In a room where any process is carried on so that irritant of offensive fumes are emitted there shall be provided suitably placed inlets of sufficient area for the supply of fresh air to the room. 4. Air analysis: - 1) Air analysis for the measurement of concentration of carbon disulphide or hydrogen sulphide shall be carried out every eight hours or at such intervals as may be directed by the Chief Inspector at places where fume process is carried on and the result of such analysis shall be recorded in a register specially maintained for the purpose. 2) If the concentration or either carbon disulphide or hydrogen sulphide exceeds 20 parts per million, the manager shall report the concentration reached and the duration of such concentration to the Chief Inspector. The report shall state the reason for such increase. 3) On receipt of such information, the Chief Inspector may direct the manager to take such measures as he may specify in that behalf and it shall be the duty of the manager to comply with such directions. 5. Electric fitting in carbon disulphide fume process-room except the spinning room: - All electric fittings in a room in which a fume process evolving carbon disulphide is carried is carried on, other than a spinning-room, shall be of flame- proof construction and all electric conductors shall either be enclosed in metal conduits or be lead-sheathed. 6. Washing facilities: - The occupier shall provide and maintain in a clean state and in good repair, for the use of all persons employed in fume process, wash place under cover with at least one tap or stand-pipe, having a constant supply of clean water for every five such persons, the taps, or stand-pipe being spaced not less than 120 centimetres apart with a sufficient supply of soap and clean towels. 7. Protective equipment: - 1) The occupier shall provide, maintain in good repair and keep in clean condition protective clothing and other equipment as specified in the table below: - Table Process Protective clothing and other equipment i) Dumping Overalls face-shields, gloves and footwear all made of suitable material. ii) Spinning Suitable aprons and gloves. iii) Process involving or Suitable gloves and footwear. likely to involve contact with viscose solution. iv) Any other process Protective clothing and equipment as may be directed by the Chief Inspector by an order writing. 2) The occupier shall make arrangements for the examination and cleaning of the protective equipment at the close of each day’s work and for the repair or replacement thereof when necessary. 8. Use of protective equipment: - Every person shall use the protective equipment provided to him under paragraph 7. 217 9. Storage of protective equipment: - A suitable room, rooms or lockers shall be provided exclusively for the storage of all the protective equipment supplied to employee and no such equipment shall be stored at any place other than the room, rooms or lockers so provided. 10. Mess-room: - 1) There shall be provided and maintained for the use of all the persons remaining within the premises during the meal intervals, a suitable mess- room providing accommodation of at least 10,000 square centimetres per head furnished with - a) a sufficient number of tables and chairs or benches with back rests. b) an arrangement for washing hands and utensils, and c) adequate means for warming food. 2) The mess-room shall be kept under the charge of a responsible person and shall be kept clean. 11. Prohibition to smoking etc. in carbon disulphide fume process room: - No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in a room in which fume producing carbon disulphide is caused and notice in the language understood by the majority of the workers shall be posted in the factory prohibiting smoking and carrying of matches, fire or naked light or other means of producing light or spark into such room. 12. Prohibition to remain in fume process room: - No person during his intervals for meal or rest shall remain in any room wherein fume process is carried on. 13. Medical examination: - 1) Every person employed in a fume process shall be examined by the Factory Medical Officer once in every six months and by the Certifying Surgeon once in every 12 months or at such other intervals as may be specified in writing by the Chief Inspector on a date or dates of which due notice shall be given to all such persons and such examination shall take place on the factory premises. 2) Every person employed in a fume process shall present himself at the appointed time for such examination. 3) A health Register containing the names of all the persons employed in a fume process shall be kept in Form 29. 4) No person, after suspension, shall be employed in a fume process without the written sanction of the Certifying Surgeon entered in the Health Register. 13 A. Medical Facilities: - 1) The occupier of the factory shall appoint at least a part-time qualified medical practitioner possessing MBBS degree and having post graduate diploma in Industrial Health or possessing MBBS degree and having five years experience in industry in industry as occupational health Physician. The medical Practitioner so appointed shall be required to put in minimum four hours attendance on every working day in the ambulance-room for carrying out the duties specified in the following sub-paragraph (2). Provided that, in case of factories employing less than 500 workers per day the Chief Inspector of Factories may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 218 2) The medical supervision of persons engaged on dangerous operations specified in rule 165 of these rules. a) to maintain Health Register in Form 29. b) to undertake medical supervision of persons engaged on dangerous operations specified in rule 165 of these rules. c) to look after health, education and rehabilitation of sick, injured or affected workers. d) to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. 3) For the purpose of medical supervision by the medical practitioner so appointed, the occupier shall provide for his exclusive use a room in the factory premises which shall be properly cleaned, adequately lightened, ventilated and furnished with a screen, a table with office stationary, chairs and other facilities and instruments including X-Ray arrangements for Schedules IV, X and XVII, for such examinations and such other equipments as may be prescribed by the Chief Inspector of factories from time to time. 14. Breathing apparatus and measures: - 1) There shall be provided in every factory where fume process is carried on, sufficient supply of : - a) a breathing apparatus. b) oxygen and suitable means of its administration, and c) life belts. 2 (i) The breathing apparatus and other appliances shall: - a) be maintain in good condition and kept in an ambulance room or in some other place so as to be readily available, and b) be thoroughly inspected once every month by a competent person, appointed in writing by the occupier. ii) A record of the condition of the breathing apparatus and other appliances shall be entered in a book provided for that purpose which shall be produced when required by an inspector. 3) Sufficient number of workers shall be trained and given a periodic refresher course in the use of breathing apparatus and respirators and artificial respiration so that at least 2 such trained persons would be available in each fume process room during all the working hours of the factory. 4) Respirators shall be kept properly labelled in clean dry, light-proof cabinets and if liable to be affected by fumes, shall be protected by suitable containers. Respirators shall be dried after use and shall be periodically disinfected. 15. Cautionary placard and instructions: - Cautionary placards in the form specified by the Chief Inspector and printed in the language of the majority of the workers employed shall be affixed in prominent places in the factory where they can be easily and conveniently read by the workers and arrangement shall be made by the occupier to instruct periodically all workers employed in a fume process regarding the health hazards connected with their duties and the best preventive measures and method to protect themselves. 219 16. Exemption: - If in respect of any factory, department or departments, the Chief Inspector is satisfied that all or any of the provisions of this Schedule are not necessary for the protection of the persons employed in such department or departments, he may, by certificate in writing, exempt such department or departments for all or any of such provisions subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector without assigning any reasons. Schedule XV Manufacture and manipulation of dangerous pesticides 1. Definition: - For the purpose of this Schedule: - a) “pesticides” means agents used for the purpose of destroying or arresting the growth or increase of harmful organisms; b) “dangerous pesticides” means insecticides as defined in section 3(e) of the Insecticides Act. 1968 (46 of 1968) or any other substance declared as dangerous pesticides by the Chief Inspector of Factories in writing; c) “Suspension” means suspension from employment, in any process in which dangerous pesticides is used by written Certificate in the Health Register of Form 29 signed by the Certifying Surgeon, who shall be competent to suspend all persons employed in such process. d) “first employment” means first employment in any manufacturing process referred to in this Schedule and also re-employment in, such manufacturing process following any cessation of employment for a continuous period exceeding three calendar month; e) “efficient exhaust draught” means localised ventilation effected by mechanical means, for the removal of gas, vapour, dust or fumes so as to prevent them from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fume or dust originates; f) “manipulation” includes mixing, blending, filling, emptying packing, handling or using of a dangerous pesticide. 2. Application: - This schedule shall apply in respect of all factories or any part thereof in which the process of manufacture or manipulation of a dangerous pesticide (hereinafter referred to as the said manufacturing process) is carried on. 3. Cautionary placard: - A cautionary placard in the form specified in Appendix attached to this Schedule and printed in the language of the majority of the workers employed, shall be affixed in prominent place frequently by them in the factory where the placards can be easily and conveniently read by the workers and arrangements shall be made by the occupier to instruct periodically all workers employed in the said manufacturing process regarding the health hazards connected with it and methods to protect themselves. 4. Prohibition relating to employment of women and young persons: - No woman or young person shall be employed or permitted to work in any room in which the said manufacturing process is carried on or in any room in which a dangerous pesticides is stored. 5. Air space: - In every room in which the said manufacturing process is carried on, there shall be atleast 15 cubic metres of air space, excluding any space occupied by machinery equipment or any other articles, for any person employed therein, 220 and in computing this air space, no height over 3.5 metres shall not be taken into account. 6. Prohibition of the said manufacturing process without efficient exhaust draught: - The said manufacturing process shall not be carried on without the use of efficient exhaust draught when: - a) a container holding a dangerous pesticide is emptied, or b) a dangerous pesticide is introduced into container, tank, hopper or machine of filled in small-sized packings, or c) a power or a liquid is prepared from a dangerous pesticide, or d) a dangerous pesticide is blended, unless the process is completely enclosed. 7. Floor of work-room: - The floor or every work-room in which the said manufacturing process is carried on shall be: - a) of cement or similar material so as to be smooth and impervious to water. b) maintained in sound condition. c) sloping and providing with gutters for adequate drainage, and d) thoroughly washed daily by means of hose-pipe. 8. Work-benches: - The work-benches at which a dangerous pesticides manipulated shall: - a) have smooth surface and be of non-absorbent material, preferably of stainless steel, and b) be cleaned daily. 9. Waste: - a) A suitable receptacle with tightly-fitting cover shall be provided and used for depositing waste like cloth, paper or other materials soiled with a dangerous pesticide. b) All such contaminated waste shall be destroyed by burning at least once a week. 10. Empty containers used for dangerous pesticides: - Such containers shall be destroyed or thoroughly cleaned of their contents and treated with an inactivating agent before discarded. 11. Manual handing: - A dangerous pesticide shall not be required or allowed to be manipulated by hand except by means of long-handled scoop. 12. Protective clothing: - 1) Protective clothing shall be provided and maintained in good repair for all workers and such clothing shall be worn by the workers concerned. The protective clothing shall consist of: - a) long pants and shirts or overalls with long sleeves and head coverings. b) rubber gloves, gum boots, rubber aprons, chemical safety goggles and respirators. Where the pesticide contains oil, the rubber gloves, boots and apron shall be of synthetic-rubber. 2) Where the worker has to handle a dangerous pesticide: - a) containing phosphorous or nicotine, the protective clothing shall be daily both inside and outside, and if the protective clothing 221 mentioned in clause (a) of sub-paragraph (1) is soiled with such pesticides it shall be changed immediately, and b) not containing phosphorus or nicotine, the protective clothing mentioned in clause (a) of sub-paragraph (1) shall be washed frequently. 13. Medical examination: - 1) a) No person shall be employed in the said manufacturing process unless he has been examined by the Certifying Surgeon within seven days preceding his first employment and certified fit for such employment. b) No person shall be employed in the said manufacturing process unless he is re-examined by the Certifying Surgeon at least once in every three calendar months. c) The Certifying Surgeon shall examine persons employed in the said manufacturing process by giving due notice to all concerned. d) A Health Register in Form 29 containing the names of all workers employed in the said manufacturing process shall be kept. e) No person after suspension shall be employed without written sanction from the Certifying Surgeon entered in or attached to the Health Register. 2) The Chief Inspector may order any suitable clinical test or tests to be carried out in respect of the workers employed in any factory where the said manufacturing process is carried on at such intervals as he deems fit. 14. Medical facilities: - 1) The occupier of the factory shall appoint atleast a part time qualified medical practitioner, possessing MBBS degree and having a diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner so appointed shall examine and, if necessary, treat on the premises of the factory all workers who handle dangerous pesticides for effects of excessive absorption at least once a week. The occupier shall make necessary arrangements to ensure quick availability of the medical practitioner so appointed or any other qualified medical practitioner in emergency cases. The medical practitioner, so appointed, shall be required to put in minimum four hours attendance on every working day in the ambulance room for carrying out the duties specified in the following sub- paragraph (2). Provided that, in cases of factories employing less than 500 workers per day, the Chief Inspector of Factory may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) The medical practitioners so appointed, shall perform, in addition to the duties specified in sub-paragraph (1) the following duties, that is to say: - a) to maintain Health Register in Form 29. b) to undertake medical supervision of persons engaged in dangerous operations specified in rule 165 of these rules, c) to look after health, education and rehabilitation of sick, injured or affected workers; d) to carry out inspection of work-room where dangerous operations are carried out and the advise the management of the measures to be adopted for protection of health of the worker involved therein. 222 15. Time allowed for washing: - Before each meal and before the end of the day’s work at least ten minutes in addition to the regular rest interval shall be allowed for washing in each person who has been employed in the said manufacturing process. 16. Washing and bathing facilities: - 1) There shall be provided and maintained in cleanly state and in good repair for the use of all persons employed, adequate washing and bathing places having a constant supply having a constant supply of water under cover at the rate of one such place for every 5 persons employed. 2) The washing places shall have stand-pipes placed at intervals of not less than one metre; 3) Not less than one half of the total number of washing place shall be provided with bath-rooms; 4) Sufficient supply of clean towels made of suitable material shall be provided; Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector; 5) Sufficient supply of soap and nail brushes shall be provided. 17. Food, drinks, etc., prohibited in work-room: - No food, drinks, pan, supari or tobacco shall be consumed or brought by any worker into any work room in which the said manufacturing process is carried on. 18. Cloak Room: - There shall be provided and maintained for the use of persons employed in the said manufacturing process: - a) a cloak-room for clothing put off during working hours with adequate arrangements for drying clothing, if wet; b) separate and suitable arrangements for the storage of protective clothing provided under paragraph 12. 19. Mess-room: - There shall be provided and maintained for the use of all persons, employed in the factory and remaining on the premises during the rest intervals, a suitable mess-room which shall be furnished with: - a) sufficient tables and benches and b) adequate means for warming food. The mess-room shall be placed under the charge of a responsible person and shall be kept clean. 20. Exemption: - If it respect of any factory the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the process or for any other reasons all or any of the provisions of this Schedule are not necessary to the protection of the persons employed in the factory, he may by a certificate in writing exempt such factory from all or any of the provisions, on such condition as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector after recording his reasons therefore. 21. Manipulation not to be undertaken :- Manipulation of a pesticide other than those mentioned in clause (b) of this Schedule shall not be undertaken in any factory unless a certificate regarding its dangerous nature or otherwise is obtained from the Chief Inspector. List of dangerous Pesticides. Parthion Chlordane 223 Diazinon Endrine. Hexaethyl tetraphosphate. Aldrin Tetraethyl pyrophophate Dieldrin Tetraethy ditriopyrophosphate Texaphene Demeton (systex) Dinitro-o-cresol Schradan (OMPR) Arsenical Compounds Para-Oxon (E.600) Cryolite Methyl Parathion. Pentachlorophenol Dimeffox Carbojuran Sulphotepp Methyl bromide EPN, Cyanides Nicotine or its compound. Mercury compounds APPENDIX X Cautionary placard 1. Pesticides are generally poisonous substances. 2. Therefore in rooms where these are handled - a) do not chew, eat, drink or smoke; keep food or drink away from pesticides; b) use the protective wear supplied e.g. gloves, aprons, clothes, boots, etc. 3. Before meals or when any part of the body has come in contact with the pesticides, wash with soap and water. 4. Before leaving the factory, take a bath and change your clothing. 5. Do not use any container that has contained a pesticide as a pot for food or drink. 6. Do not handle any pesticide with bare hands; use a handled scoop. 7. Avoid spilling of any pesticide on body, floor or table. 8. Maintain scrupulous cleanliness of body and clothing and of your surroundings. 9. In case of sickness like nauses, vomiting or giddiness, inform the manager who will make necessary arrangement for treatment. SCHEDULE XVI Compression of Oxygen and Hydrogen Produced by Electrolytic Process or by Steam iron process. 1. Definition: For the purpose of this schedule “Compression of Oxygen and Hydrogen” means any process by which oxygen or hydrogen is manufactured or evolved by electrolytic process or by steam iron process. 2. Application: This schedule applies in respect of factories or any part thereof in which the process if compression of oxygen and hydrogen is carried on. 3. Situation of electrolyser plant room etc: The room in which electrolyser plant is installed shall be separate from the plant for storing and compressing oxygen and hydrogen. The room in which electric generator and the distribution panel are installed shall not communicate with any other room in which any process is carried on. 4. Testing the purity of oxygen and hydrogen: 1) The purity of oxygen and hydrogen shall be tested by a competent person at least once in every shift, at the following points: 224 i) in the electrolyser room, ii) at the gas holder inlet, and iii) at the suction end of the compression, Provided that where the electrolyser plant is fitted with automatic recorder of purity of oxygen and hydrogen with alarm lights, the purity of the gases may be tested likewise at the suction end of the compressor only. 2) The purity figures obtained as a result of the test shall be entered and signed by the person carrying out such test in a register, to be kept for the purpose. 5. Compression of oxygen and hydrogen prohibited in certain circumstances: Where the purity of oxygen and hydrogen as tested under paragraph 4 is found to be less than 98%, the oxygen or hydrogen shall not be subjected to the process of compression. 6. Provision of negative pressure switch: In addition to the limit switch, to switch off the compressor motor, to make it impossible to empty the gas holder to the point causing vacuum inside the gas holder, a sensitive negative pressure switch shall be provided in or adjacent to the suction main for hydrogen compressor, to switch off the compressor motor in the event of the gas holder being emptied to the extent as to cause vacuum. 7. Warning Signal: The bell of any holder shall not be permitted to go within 30 cm of its lowest position when empty and a visual and an audible warning signal shall be fitted to the gas holder to indicate that this limit is reached. 8. Purity of Raw Material: The water and caustic soda used for making lye shall be chemically pure within the pharmaceutical limits. 9. Construction of Electrical Connections: Electrical Connection at the electrolyser cells and at the electric generator terminals shall be so constructed as to preclude the possibility of wrong connections leading to the reversal of polarity. An automatic device shall be provided to cut off power in the event of reversal polarity owing to wrong connection either at the switch board or at the electric generator terminals. 10. Maintenance of Gas Pipe, Gas Holder and Compressed Gas Storage Vessels: i) Oxygen and Hydrogen gas pipes shall be painted with distinguishing colours. In the event of leakage at the joints of the hydrogen gas pipe, holder or a storage vessel or in the event of any breakdown, the pipe and storage system after repairs and reconnections carried out as per paragraph 13 of this schedule and in accordance with the requirements of Rule 86 shall be purged of all air and gasses using a suitable inert gas, before drawing in hydrogen gas. ii) Before drawing in hydrogen gas in any new or existing system not in use every pipe, gas holder, compressed gas vessels in the system shall be purged of all air and gases using a suitable inert gas. 11. Electrical Wiring and Other sources if Ignition: Wherever hydrogen gas is generated, compressed, transferred or stored all electrical wiring, apparatus and other installations shall be of flame proof construction. All sources of ignition shall be of prevented from being present in the above areas. A warning notice shall be exhibited to that effect at prominent place in the above areas. 12. Removal of Explosive Substances: No part of the electrolyser plant and the gas holders, and compressor shall be subjected to welding, brazing, soldering or cutting until steps have been taken to remove any explosive substance from that 225 part and it is rendered safe for such operation. After the completion of such operation no explosive substance shall be allowed to enter that part until the metal has cooled sufficiently to prevent risk of explosion. 13. Restriction of Operation, Repair etc. No work of operation, repair or maintenance shall be undertaken except under the direct supervision of a person who, by his training, experience and knowledge of the necessary precautions against risk of explosion is competent to supervise such work. No electric generator after erection or repairs shall be switched on to the electrolyser unless it is certified by any competent person under whose direct supervision, erection or repairs are carried out to be in a safe condition and the terminals have been checked for the polarity as required by these Rules. 14. Examination of the Paint. : Every part of the electrolyser plant and the gas holders and compressor shall be inspected, checked and overhauled in accordance with a regular schedule maintained by the manager complying with the instruction of the competent persons mentioned in paragraph 13. Every defect noticed shall be rectified forthwith. Schedule XVII Handling and processing of Asbestos, Manufacture of any Article of Asbestos and any other process of manufacture or otherwise in which Asbestos is used in any form. 1. Application: - This schedule shall apply to all factories or parts of factories in which any of the following processes is carried on: - a) breaking, crushing, disintegrating, opening, grinding, mixing or sieving of asbestos and any other processes involving handling and manipulation of asbestos incidental thereto; b) all process in the manufacture of asbestos textiles including preparatory and finishing processes; c) making of insulation slabs or sections, composed wholly or partly of asbestos, and processes incidental thereto; d) making or repairing of insulating mattresses, composed wholly or partly of asbestos, and processes incidental thereto; e) manufacture of asbestos cardboard and paper; f) manufacture of asbestos cement goods; g) application of asbestos by spray method; h) sawing, grinding, turning, abrading and polishing in dry state of articles composed wholly or partly of asbestos; i) cleaning of any room, vessel, chamber, fixture of appliance for the collection of asbestos dust; and j) any other processes in which asbestos dust is given off into the work if environment. 2. Definition: - For the purpose of this schedule: - a) “asbestos” means any fibrous silicate mineral and any admixture containing actionolite, amosite, anthophyllite, thrysotile, crocidolite, tremolite or any mixture thereof, whether crude, crushed or opened; b) “asbestos textiles” means yarn or cloth composed of asbestos or asbestos mixed with any other material; c) “approved” means approved for the time being inwriting by the Chief Inspector; 226 d) “breathing apparatus” means a helmet or face piece with necessary connection by means of which a person using it breathes air free from dust, or any other approved apparatus; e) “efficient exhaust draught” means localised ventilation by mechanical means for the removal of dust so as to prevent dust from escaping into air of any place in which work is carried on. No draught shall be deemed to be efficient which fails to control dust produced at the point where such dust originates, f) “preparing” means crushing, disintegrating and any other process in or incidental to the opening of asbestos; g) “protective clothing” means overalls and head covering which (in either case) will when worn exclude asbestos dust. 3. Tools and Equipment: - Any tools or equipment used in processes to which this schedule applied shall be such that they do not create asbestos dust above the permissible limit or are equipped with efficient exhaust draught. 4. Exhaust draught: - 1) An efficient exhaust draught shall be provided and maintained to control dust from the following process and machines; a) manufacture and conveying machinery namely; i) preparing, grinding or dry mixing machines; ii) carding, card waste and ring spinning machines and looms; iii) machines or other plant fed with asbestos and iv) machines used for the sawing, grinding, turning, drilling, abrading or polishing, in the dry state of articles composed wholly or partly of asbestos; b) cleaning and grinding of the cylinders or other parts of a carding machine. c) chambers, hoppers or other structures into which loose asbestos is delivered or passes; d) work-benches for asbestos waste sorting or for other manipulation of asbestos by hand; e) work place at which the filling or emptying of sacks, skips or other portable containers, weighing or other process incidental thereto which is effected by hand, is carried on; f) sack cleaning machines; g) mixing and blending of asbestos by hand; and h) any other process in which dust is given off into the work environment. 2) Exhaust ventilation equipment provided in accordance with sub-paragraph (1) shall while any work of maintenance or repair to the machinery, apparatus or other plant or equipment in connection with which it is provided is being carried on, kept in use so as to produce an exhaust draught which prevents the entry of asbestos dust into the air of any work place. 3) Arrangements shall be made to prevent asbestos dust discharged from exhaust apparatus being drawn into the air of any workroom. 227 4) The asbestos bearing dust removed from any workroom by the exhaust system shall be collected in suitable receptacles or filter bags which shall be isolated from all work areas. 5. Testing and examination of ventilating systems: - 1) All ventilation systems used for the purpose of extracting or suppressing dust as required by this schedule shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examinations or test shall be rectified forthwith. 2) A register containing particulars of such examination and tests and the state of the plant and the repair to the machinery, apparatus or other plant or equipment in connection with which it is provided is being carried on, be kept in use so as to produce an exhaust draught which prevents the entry of asbestos dust into the air of any work place. 3) Arrangements shall be made to prevent asbestos dust discharged from exhaust apparatus being drawn into the air of any workroom. 4) The asbestos bearing dust removed from any workroom by the exhaust system shall be collected in suitable receptacles or filter bags which shall be isolated from all work areas. 5. Testing and examination of ventilating system: - 1) All ventilation systems used for the purpose of extracting or suppressing dust as required by this schedule shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examinations or test shall be rectified forthwith. 2) A register containing particulars of such examination and tests and the state of the plant and repairs or alteration (if any) found to be necessary shall be kept and shall be available for inspection by an inspector. 6. Segregation in case of certain process: - Mixing or blending of asbestos by hand, or making or repairing of insulating mattresses composed wholly or partly of asbestos shall not be carried on in any room in which any other work is done. 7. Storage and distribution of loose asbestos: - All loose asbestos shall while not in use be kept in suitable closed receptacles which prevent the escape of asbestos dust there from such asbestos shall not be distributed within a factory except in such receptacles or in a totally enclosed system of conveyance. 8. Asbestos sacks: - 1) All sacks used as receptacles for the purpose of transport of asbestos within the factory shall be constructed of impermeable materials and shall be kept in good repair. 2) A sack which has contained asbestos shall not be cleaned by hand beating but by a machine, complying with paragraph 3. 9. Maintenance of floors and workplaces: - 1) In every room in which any of the requirements of this scheme apply- a) the floors, work-benches, machinery and plant shall be kept in a clean state and free from asbestos debris and suitable arrangements shall be made for the storage of asbestos not immediately required for use; and 228 b) the floors shall be kept free from any materials, plant or other articles not immediately required for the work carried on in the room, which would obstruct the proper cleaning of the floor. 2) The cleaning as mentioned in sub-rule(1) shall so far as is practicable, be carried out by means of vacuum cleaning equipment so designed and constructed and so used that asbestos dust neither escape nor is discharged into the air of any work-place. 3) when the cleaning is done by any method other than that mentioned in sub- paragraph (2), the persons doing cleaning work and any other person employed in that room, shall be provided with respiratory protective clothing. 4) The vacuum cleaning equipment used in accordance with provisions of sub-paragraph (2), shall be properly maintained and after each cleaning operation, its surface kept in a clean state and free from asbestos waste and dust. 5) Asbestos waste shall not be permitted to remain on the floors or other surfaces at the work place at the end of the working shift and shall be transferred without delay to suitable receptacles. Any spillage of asbestos waste occurring during the course of the work at any time shall be removed and transferred to the receptacles maintained for the purpose without delay. 10. Breathing apparatus and protective Clothing: - 1) An approved breathing apparatus and protective clothing shall be provided and maintained in good conditions for use of every persons employed. a) in chambers containing loose asbestos; b) in cleaning, dust settling or filtering chambers of apparatus; c) in cleaning the cylinders, including the doffer cylinders, or other parts of a carding machine by means of hand-strickles; d) in filling, beating, or levelling in the manufacture or repair of insulating mattress, and e) in any other operation or circumstance in which it is impracticable to adopt technical means to control asbestos dust in the work environment within the permissible limit. 2) Suitable accommodation in conveniently accessible position shall be provided for the use of persons when putting on or taking off breathing apparatus and protective clothing provided in accordance with this rule and for the storage of such apparatus and clothing when not in use. 3) All breathing apparatus and protective clothing when not in used shall be stored in the accommodation provided in accordance with sub-rule (2) above. 4) All protective clothing in use shall be de-dusted under an efficient exhaust draught or by vacuum cleaning and shall be washed at suitable intervals. The cleaning schedule and procedure should be such as to ensure the efficiency in protecting the wearer. 5) All breathing apparatus shall be cleaned and disinfected at suitable intervals and thoroughly inspected once every month by a responsible person. 229 6) A record pf the cleaning and maintenance and of the condition of the breathing apparatus shall be maintained in a register provided for that purpose which shall be readily available for inspection by an Inspector. 7) No persons shall be employed to perform any work specified in sub- paragraph (1) for which breathing apparatus is necessary to be provided under that sub-paragraph unless he has been fully instructed in the proper use of that equipment. 8) No breathing apparatus provided in pursuance of sub-paragraph (1) which has been worn by a person shall be worn by another persons unless it has been thoroughly cleaned and disinfected since use of that equipment. 11. Separate accommodation for personal clothing: - A separate accommodation shall be provided in conveniently accessible position for all persons employed in operations to which this schedule applies for storing of personal clothing. This should be separated from the accommodation provided under sub-paragraph (2) to prevent contamination of personal clothing. 12. Washing and bathing facilities: - 1) There shall be provided and maintained in clean stage and in good repair for the use of all workers employed in the processes covered by the schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 15 persons employed. 2) The washing places shall have standpipes placed at intervals of not less than one metre. 3) Not less than one half of the total number of washing places shall be provided with bathrooms. 4) Sufficient supply of clean towels made of suitable material shall be provided. Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. 5) Sufficient supply of soap and nail brushes shall be provided. 13. Messroom: - 1) There shall be provided and maintained for the use of all workers employed in the factory covered by this schedule, remaining on the premises during the rest intervals, a suitable messroom which shall be furnished with; a) sufficient tables and benches with back rest, and b) adequate means of warming food. 2) The messroom shall be placed under the charge of a responsible person and shall be kept clean. 14. Prohibition of employment of young persons: - No young person shall be employed in any of the process covered by this schedule. 15. Prohibition relating to smoking: - No person shall smoke in any area where processes covered by this schedule are carried on. A notice in the language understood by majority of the workers shall be posted in the plant prohibiting smoking at such areas. 16. Cautionary Notice: - 1) Cautionary notices shall be displayed at the approaches and along per metre of every asbestos processing area to warn all persons regarding: - 230 a) hazaros to health from asbestos dust. b) need to use appropriate protective equipment; c) prohibition of entry to unauthorised persons or authorised persons but without protective equipment. 2) Such notice shall be in the language understood by the majority of the workers. 17. Air monitoring: - To ensure the effectiveness of the control measures, monitoring of asbestos fibre in air shall be carried out once atleast in every shift and the record of the results so obtained shall be entered in a specially maintained for the purpose. 18. Medical examination: - a) No worker shall be employed in any factory on any of the processes specified in clause 1, unless he has been medically examined by the Medical Inspector of Factories/ certifying Surgeon and has been declared fit and granted a certificate of fitness in Form 28. b) Every worker employed on any of the aforesaid processes on the date on which the Schedule comes into force shall be radiologically examined by the qualified radiologist at the cost of the occupier and the standard size- X-ray plate shall be submitted to the Medical Inspector of Factories/ Certifying Surgeon for medical examination within three months of the said date. c) Every worker employed on any of the aforesaid processes shall be medically examined by the Medical Inspector of Factories/ Certifying Surgeon at intervals of twelve months after the first medical examination conducted under sub-clauses (a) and (b). If at any time the Medical Inspector of Factories/ Certifying Surgeon is of the opinion that the person employed in the said process shall be examined radiologically by a qualified radiologist, he may direct the occupier to arrange for such examination at his cost and then to submit the standard size chest-X-ray. Plate of the worker to the Medical Inspector of Factories/ Certifying Surgeon. d) A worker already in employment and declared unfit by the Medical Inspector of Factories/ Certifying Surgeon shall not be allowed to work on any of the processes specified in clause (1), unless he has been examined again along with standard size chest X-ray plate from a qualified radiologist at the cost of the occupier and has been certified to be fit to work on the said processes again. e) A worker declared to be unfit to work on any of the aforesaid processes, a may be employed on such other work on process as may be considered safe and as may be advised by the Medical Inspector of Factories/ Certifying Surgeon; f) The Medical Inspector of Factories/ Certifying Surgeon may direct that a worker may be X-rayed or he may be subjected to further examination by a specialist or to any other examination clinical, pathological or otherwise or that he should undergo a specified treatment, and it shall be the responsibility of the employer (occupier and manager) to arrange for the specified examined and/ or treatment and to bear all expenses thereof or in connected therein. g) The Certifying Surgeon shall after each examination grant a certificate in Form 28. 231 h) The manager shall maintain all the certificates in a proper register or file and shall produce all the certificates before an Inspector whenever demanded. i) The manager shall maintain the detail of every Medical Examination in Form 29 and the register shall be produced before an Inspector whenever demanded. The register shall be maintained upto a minimum period of 40 years from the beginning of the employment whichever is later. 19. Medical facilities: - 1) The occupier of the factory shall appoint at least a part-time qualified medical practitioner, possessing MBBS degree and having post-graduate diploma in Industrial Health or possessing MBBS degree and having five years experience in Industry as occupational health physician. The medical practitioner so appointed shall be required to put in minimum four hours attendance on every working day in the ambulance room for carrying out the duties specified in the following sub-paragraph (2). Provided that, in cases of factories employing less than 500 workers per day, the Chief Inspector of Factories may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) The medical practitioner so appointed shall perform the following duties that is to say; a) to maintain Health Register, in Form 29. b) to undertake medical supervision of persons employed in the factory. c) to look after health, education and rehabilitation of sick, injured or affected workers; d) to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. 3) For the purpose of medical supervision by the medical practitioner so appointed the occupier shall be provided for his exclusive use a room in the factory premises which shall be properly cleaned, adequately lighted, ventilated and furnished with a screen, a table with office stationary, chairs and other facilities and instruments including X-ray arrangement for such examinations and such other equipments as may be prescribed by the Chief Inspector from time to time. 20. Exemptions: - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reasons all or any of the provisions of this schedule is not necessary for protection of the workers, in the factory, the Chief Inspector may by a certificate in writing which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions., if any, as he may specify therein. Schedule XVIII Manufacture or Manipulation of Manganese and its Compound 1. Definition: For the purpose of this schedule: - a) “Manganese Process” means processing, manufacture or manipulation of manganese or any compound of manganese or any ore or any mixture containing manganese. 232 b) “First Employment” means first employment in ay manganese process and includes also re-employment in any manganese process following any cessation of employment for a continuous period exceeding 3 calendar months. c) “Manipulation” means mixing, blending, filling, emptying, grinding, sieving, drying, packing sweeping or otherwise handling of manganese or a compound of manganese, or an ore mixture containing manganese. d) “Efficient Exhaust Draught” means localised ventilation effected by mechanical means for the removal of dust or fume or mist at its source of origin so as to prevent it from it from escaping into the atmosphere of any place where any work is carried on. No draught shall be deemed to be efficient which fails to remove dust or fume or mist at the point where it is generated and fails to prevent it from escaping into and spreading into the atmosphere of a work place. 2. Application: - The schedule shall apply to every factory in which or in an part of which any manganese process is carried on. 3. Exemption: - If in respect of any factory, the Chief Inspector is satisfied that owing to any exceptional circumstances, or infrequency of the process, or for any other reason, application of all or any of the provisions of this schedule is not necessary for the protection of the persons employed in such factory he may by an order in writing which he may at his discretion revoke, exempt such factory from all or any of the provisions on such conditions and for such period as he may specify in the said order. 4. Isolation of process: - Every manganese process which may give rise to dust, vapour or mist containing manganese, shall be carried on in a totally enclosed system or otherwise effectively isolated from other process so that other plants and processes and other parts of the factory and persons employed on other work or process may not be affected by the same. 5. Exhaust draught: - No process in which any dust, vapour or mist containing manganese is generated shall be carried out except under an efficient exhaust draught which shall be applied as near to the point of generation as practicable. 6. Medical facilities: 1) The occupier of the factory shall appoint a qualified Medical Practitioner whose appointment shall be subject to confirmation by the Chief Inspector. The qualified Medical Practitioner so appointed shall be called Appointed Doctor (Appointed Doctor shall be required to put in minimum four hours attendance on every working day in the ambulance room for carrying out the duties specified in the following sub-paragraphs (3) (4) and (5). Provided that, in the case of factories employing less than 500 workers per day, the Chief Inspector of Factories may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) The occupier shall provide for the purpose of Medical Examination a room at the factory premises for exclusive use by appointed doctor. The rooms so provided shall be properly clean, (with writing materials), chairs and facilities shall instruments for examination and investigation. Such facilities shall be subject to approval by the Medical Inspector of Factories. 3) The appointed doctor shall carry out pre-employment examination of every persons intended to be employed in manganese process. All workers employed in manganese process shall be examined by the appointed doctor at an interval not exceeding three months and records of such examination shall be maintained in Form approved by the Chief Inspector shall be made available to any Inspector on demand. 233 4) The occupier and the appointed doctor of the factory shall notify forthwith any case or suspected case of poisoning by manganese to the Chief Inspector and Medical Inspector. 5) In addition to the duties specified in sub paragraph 3 & 4, the appointed doctor shall perform the following duties, that is to say: - a) to maintain Health Register in Form 29. b) to undertake medical supervision of persons engaged in dangerous operations specified in Rule 165 of these Rules; c) to look after health, education and rehabilitation of sick, injured and affected workers; d) to carry out inspection of work rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. 7. Medical Examination: 1) Every person employed in a manganese process shall be medically examined by Medical Inspector of Factories and/ or Certifying Surgeon within14 days of his first employment and thereafter at intervals of not more than six months. 2) If a person medically examined is found fit for employment on manganese process, the Medical Inspector/ Certifying Surgeon shall grant a certificate of fitness in Form 28 which shall be kept in the custody of the Manager of the Factory. The certificate shall be readily produced by the manager whenever required by an Inspector and the person granted such a certificate shall be provided with a token made of metal with the number of the certificate inscribed thereon and said person shall always carry said token on the person while at work. 3) If a person found unfit for work in any manganese process the Medical Inspector of Factories/ Certifying Surgeon shall grant a certificate to that effect and such person shall not be allowed to work in ay manganese process. 4) If the Medical Inspector/ Certifying Surgeon finds that any worker who had been granted a certificate of fitness at a previous medical examination is no longer fit to be employed on any manganese process, he may revoke the previous certificate and no person whose certificate of fitness has been revoked shall be allowed to work on any manganese process. The medical Inspector/ Certifying Surgeon may requires such person to be produced before him for fresh medical examination after such period as he may specify in writing on the revoked certificate and in the Health Register in Form 29. 5) If the Medical Inspector/ Certifying Surgeon is of the opinion that person had become permanently unfit for employment on any manganese process he shall make an entry to that effect in the certificate and in the Health Register and no such person shall be allowed to work in any manganese process. 6) If the Medical Inspector/ Certifying Surgeon is of the opinion that any special expert examination or test is necessary for a proper diagnosis in a doubtful case, he may direct the manager and/ or the Occupier to get the worker examined by such expert, or to get such tests carried out as may be specified by him and the Manager of the Occupier as the case may be shall comply with the direction given within a specified time and produce the report of examination or test as the case may be before the Medical Inspector/ Certifying Surgeon. 234 7) If the Medical Inspector/ Certifying Surgeon is of the opinion that any person is not fit for employment in any manganese process but is fit to be employed on any other work he may advise the Manager or the Occupier to employ the said person on such other job as may be safe for him. The Medical Inspector/ Certifying Surgeon may advise the worker to undergo such treatment as he may consider necessary. 8) If any person has any doubt regarding the diagnosis or decision of the Medical Inspector/ Certifying Surgeon, he may make an appeal to the Chief Inspector of Factories/ and the Chief Inspector may refer the case to the Medical Inspector or to a Medical Committee constituted by him for this purpose of which the Medical Inspector shall be a member. The decision of the Medical Inspector of the Committee as the case may be shall be final in the matter. 8. Personal Protective Equipment: - 1) The Occupier of the factory shall provide and maintain in good and clean condition suitable overalls and coverings for all persons employed in any manganese process and such overalls and head coverings shall be worn by the persons while working on a manganese process. 2) The Occupier of the factory shall suitable respiratory protective equipment for use by workers in emergency to prevent inhalation of dusts, fumes or mists. Sufficient number of complete sets of such equipment shall always be kept near the work place and the same shall be properly maintained and kept always in a condition to be used readily. 3) The occupier shall provide and maintain for the use of all persons employed, suitable accommodation for the storage and make adequate arrangements for cleaning and maintenance of personal protective equipments. 9. Prohibition relating to women and young persons: - No women or young persons shall be employed or permitted to work in any manganese process. 10. Food, drinks prohibited in work-room: - No food, drinks, pan and supari or tobacco shall be allowed to be brought into or consumed by any worker in any work-room in which any manganese process is carried on. 11. Mess room: - There shall be provided and maintained for the use of persons employed in a manganese process a suitable mess room which shall be furnished with sufficient tables and benches and adequate means for warming of food. The mess room shall be placed under the charge of responsible person and shall be kept clean. 12. Washing and bathing facilities: - The following washing and bathing facilities shall be provided and maintained in clean state and in good repair for the use of all persons employed in manganese process: - a) A wash place under cover with clean towels, soap and nail brushes and with at least one stand pipe for every ten such persons having constant supply of water. b) 50 percent of the stand pipes provided under item(s) above may be located in bathroom where water shall be made available during the working hours of the factory and for one hour thereafter. c) Clean towels to be provided individually to each worker and supply hot water of so ordered by an inspector. d) In addition to taps mentioned under item(a) one stand pipe in which warm water is made available to the provided on each floor. 13. Cloak-room: - If the Chief Inspector so requires, there shall be provided and maintained for the use of persons employed in manganese process a cloak room 235 for clothing put of during working hours with adequate arrangement for drying the clothing. 14. Cautionary placard and instructions: - Cautionary notices in the following form and printed in the language of the majority of the workers employed shall be affixed in prominent places in the factory where they can be easily and conveniently read by the workers and arrangement shall be made by the occupier to instruct periodically all workers employed in a manganese process regarding the health hazards connected with their duties and best preventive measures and methods to protect themselves. The Notice shall always be maintained in a legible condition: - Cautionary Notice Manganese and Manganese Compounds 1. Dust, fumes and mists of manganese and compounds are toxic when inhaled or ingested. 2. Do not consume food or drink near the work place. 3. Take a good wash before taking meals. 4. Keep the working area clean. 5. Use the protective clothing and equipments provided. 6. When required to work in situations where dust, fumes or mists are likely to be inhaled, use respiratory protective equipment provided for the purpose. 7. If you get severe headaches, prolonged sleeplessness or abnormal sensations on the body, report to the Manager who would make arrangement for your examination and treatment. Schedule XIX Carbon di-Sulphide Plants 1. Application : This schedule shall apply to all electric furnaces in which carbon di- sulphide is generated and all other plants where carbon di-sulphide after generation, is condensed, refined and stored. This rules are in addition to and not in derogation of any of the provisions of the Act and Rules made there under. 2. Construction, Installation and Operation: a) the buildings in which electric furnaces are installed and carbon di-sulphide after generation is condensed and refined shall be segregated from other parts of the factory and shall be of open type to ensure optimum ventilation and the plant lay out shall be such that only a minimum number of workers are exposed to the risk of any fire or explosion at one time. b) Every electric furnace and every plant in which carbon di-sulphide is condensed, and refined and stored with all their fittings and attachments shall be of good construction, sound material and of adequate strength to sustain the internal pressure to which the furnace or the plant may be subjected and shall be so designed that carbon di-sulphide liquid and gas are in closed system during their normal working. c) The electric furnace supports shall be firmly and adequately grouted in concrete or by other effective means. d) Every electric furnace shall be installed and operated according to manufacturer’s instructions and these instructions shall be clearly imparted to the personnel in charge of construction and operation. e) The instructions regarding observances of correct furnace temperature, sulphur doze, admissible current/power consumption and periodical checking of charcoal level shall be strictly complied with. 236 3. Electrodes: a) Where upper ring electrode(s), made of steel are used in the electric furnace, they shall be seamless tube construction and shall have arrangements for being connected to cooling water system through a siphon built in the electrodes or through a positive pressure water pump. b) The arrangements for cooling water referred to in clause (a) shall be connected with automatic alarm system which will actuate in the event of interruption of cooling water in the electrodes and give visible and audible alarm signals in the control room and simultaneously stop power supply for the furnace operation and to stop the further supply of water. The alarm system and the actuating device shall be checked every day. 4. Maintenance of charcoal level:- It shall be ensured that the electrodes are kept covered with charcoal bed when the furnace is in operation. 5. Charcoal separator:- An effective arrangement shall be provided to prevent entry of pieces of charcoal into the condensers and piping. 6. Rupture discs and safety seal:- a) At least two rupture discs of adequate size which shall blow off at a pressure twice the maximum operating pressure shall be provided on each furnace and shall either be mounted directly on the top of the furnace or each through an independent pipe as close as possible to the furnace. b) A safety water seal shall be provided and tapped from a point between the off take pipe from the electric furnace and sulpher separator. 7. Pyrometers and Manometers: a) Each electric furnace shall be fitted with adequate number of pyrometers to indicate temperature as near to the correct figures as practicable, at various points in the furnace. The dials for reading the temperatures shall be located in the control room. b) Monometer or any other suitable device shall be provided for indicating pressure- i) in the off take pipe before and after the sulphur separator, and ii) in primary and secondary condensers. 8. Prevention of Back flow of Gas: i) All piping carrying carbon di sulphide shall be fitted with check valves, water peals or some other effective devices at suitable position so as to prevent gas from flowing back into any electric furnaces in the event is shutdown. ii) Overhead storage tank(s) of adequate capacity shall be provided to ensure supply of cooling water by direct gravity feed to the condensers in case of emergency such as power shutdown etc. At least for the duration during which it would be possible to initiate and complete procedures for the shutdown of the furnace. 9. Inspection and maintenance of electric furnace: a) Every electric furnace shall be inspected internally by a competent person; i) before being placed in service after installation, ii) before being placed in service after reconstruction or repair, and iii) periodically every time the furnaces are opened for cleaning or dashing or for replacing electrodes. b) When electric furnace is shutdown fro cleaning or deashing: i) the brick lining shall be checked for continuity and any part found defective removed. 237 ii) after removal of any part of the lining, referred to in (a) the conditions of the shell shall be closely inspected; and iii) any places forming shell found corroded to the extent that safety of the furnace is endangered shall be replaced. 10. Maintenance of Records: The following hourly records shall be maintained in log book: i) Manometer readings at the points specified in 7(b)(i) and (ii). ii) Gas temperature indicated by pyrometers and all other vital points near the sulphur separator and primary and secondary condensers. iii) Water temperature and flow of water through the siphon in the electrodes, provided that where there is a system for positively ensuring more than the minimum requirement of water flow through siphon system and where an arrangement is also available for an instaneous cut off of power where ever there is low flow of water, the provisions of the sub clause may not apply, iv) Primary and secondary voltages, current and energy consumed. 11. Electrical apparatus, wiring and fittings:- All buildings in which carbon di- sulphide is refined or stored shall be provided with electrical apparatus, wiring and fittings which shall afford adequate protection from the fire and explosion. 12. Prohibition relating to smoking:- No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in buildings in which carbon di-sulphide is refined or stored, and a notice in the language understood by a majority of the workers shall be pasted in the plant prohibiting smoking and carrying of matches, fire or naked light or other means of producing naked light or spark into such rooms. 13. Means of escape:- Adequate means of escape shall be provided and maintained to enable persons to move to sage place as quickly as possible in case of an emergency. At least two independent staircases of adequate width shall be provided in every building housing the furnaces at reasonable intervals at opposite ends. These shall always be kept clear of all obstructions and so designed as to afford easy passage. 14. Warning in case of fire:- There shall be adequate arrangement for giving warnings in case of fire or explosion which shall operate on electricity and in case of failure of electricity by some mechanical means. 15. Fire-fighting equipment:- a) Adequate number of suitable fire extinguisher or other fire-fighting equipment shall be kept in constant readiness for dealing with risks, involving and depending on the amount and nature of materials stored. b) Clear instructions as to how the extinguishers or other equipment should be used printed in the language which the majority of the workers employed understand, shall be affixed to each extinguisher or other equipment and the personnel trained in their use. 16. Bulk-sulphur:- a) Open or semi-enclosed spaces for storage of bulk sulphur shall be sited with due regard to danger which may arise from sparks given off by nearby locomotives etc. and precautions shall be taken to see that flames, smoking and matches and other sources of ignition do not come in contact with the clouds of dust arising during handling of bulk sulphur. b) All enclosures for bulk sulphur shall be of non-combustible construction, adequately ventilated and so designed as to provide a minimum of ledges on which dust may lodge. 238 c) The bulk sulphur in the enclosures shall be handled in such a manner as to minimize the formation of dust clouds and no flame, smoking or matches or other sources of ignition shall be employed during its handling. d) No repairs involving flames, heat or use of hand or power tools shall be made in the enclosure where bulk sulphur is stored. 17. Liquid sulphur:- Open flames, electric sparks and other sources of ignition, including smoking and marches, shall be excluded from the vicinity of molten sulphur. 18. Training and supervision:- a) All electric furnaces and all plants in which carbon di-sulphide is concerned, refined or stored shall be under adequate supervision at all times while the furnaces and plant are in operation. b) Workers in-charge of operation and maintenance of electric-furnaces and the plants shall possess qualifications at least equivalent to High School Leaving Certificate Examination and shall also be adequately trained. 19. Washing facilities:- The occupier shall provide and maintain in a clean state and in good repair, for the use of all persons employed wash place under cover with at least one tap or stand pipe, having a constant supply of clean water for every five such persons, the taps or stand-pipes being spaced not less than 120 centimetres apart with a sufficient supply of soap and clean towels provided that towels shall be supplied individually to each worker if so ordered by Inspector. All the workers employed in the sulphur storage, handling and melting operations shall be provided with a nail brush. 20. Personal protective equipment:- a) Suitable goggles and protective clothing consisting of overalls without pockets, gloves and foot-wear shall be provided for the use of operatives:- i) when operation valves or cocks controlling fluids etc. ii) drawing off of molten sulphur from sulphur pots, and iii) handling charcoal or sulphur. b) Suitable respiratory protective equipment shall be provided and stored in the appropriate place for use during abnormal conditions or in an emergency. c) A arrangement shall be made for the proper and efficient cleaning of all such protective equipment. 21. Cloak-room:- There shall be provided and maintained for the use of all persons employed in the processes a suitable cloak room for clothing put off during work hours and a suitable place separate from the cloak room for the storage of overalls or working clothes. The accommodation so provided shall be placed in the charge of a responsible person and shall be kept clean. 22. Unauthorized persons:- Only maintenance and repair personnel, persons directly connected with the plant operation and those accompanied by authorized persons shall be admitted into the plant. Schedule XX Benzene 1. This schedule is made to provide protection against hazards of poisoning from benzene and shall apply in respect of factories or parts thereof in which benzene or substances containing benzene are manufactured, handled or used. 2. Definitions:- For the purpose of this schedule:- a) “Substances containing benzene” means substances wherein benzene content exceeds 1 per cent by volume. 239 b) “Substitute” means a chemical which is harmless or less harmful than benzene and can be used in place of benzene. c) “Enclosed system” means a system which will not allow escape of benzene vapours to the working atmosphere. d) “Efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gases, vapours and dusts or fumes so as to prevent them from escaping into the air of any work room. No draught shall be deemed to be efficient if it fails to remove smoke generated at the point where such gases, vapour, fumes or dusts originate. 3. Prohibition and substitution a) Benzene or substances containing benzene shall not be used as a solvent or diluents unless the process in which it is used is carried on in an enclosed system or unless the process is carried on in a manner which is considered equally safe as if it were carried out in an enclosed system. Use of benzene and substances containing benzene is prohibited in the following processes, namely; i) manufacture of varnishes, paints and thinners; ii) cleaning and degreasing operations. b) Where suitable substitutes are available, they shall be used instead of benzene or substances containing benzene. This provision, however, shall not apply to the processes specified in Appendix A. c) The Chief Inspector may, subject to confirmation by the State Government, permit exemptions from the percentage laid down in clause 2(a) and also from the provisions of sub-clause(b) temporarily under conditions and within limits of time to be determined after consultation with the employers and workers concerned. 4. Protection against inhalation:- a) The process involving the use of benzene or substances containing benzene shall as far as practicable be carried out in an enclosed system. b) Where, however, it is not practicable to carry out the process in an enclosed system, the workroom in which benzene or substances containing benzene are used shall be equipped with an efficient exhaust draught or other means for the removal of benzene vapours to prevent their escape into the air of the work room so that the concentration of benzene in the air does not exceed 25 parts per million by volume or 80mg/m3. c) Air analysis for the measurement of concentration of benzene vapours in air shall be carried out every 8 hours or at such intervals as may be directed by the Chief Inspector at places where process involving use of benzene is carried on and the result of such analysis shall be recorded in a register specially maintained for this purpose. If the concentration of benzene vapours in air as measured by air analysis, exceeds 25 parts per million by volume or 80 mg/m3 the Manager shall forthwith report the concentration to the Chief Inspector stating the reasons for such increase. d) Workers who for special reasons are likely to be exposed to concentration of benzene in the air of the workroom exceeding the maximum referred to in clause (b) shall be provided with the suitable respirators or face masks. The duration of such exposure shall be limited as far as possible. 5. Measure against skin contact:- a) Workers who are likely to come in contact with liquid benzene or substances containing benzene shall be provided with suitable gloves, aprons, boots and where necessary vapour tight chemical goggles, made of materials not affected by benzene or its vapours. 240 b) The protective wear referred to in sub-clause a) shall be maintained in good condition and inspected regularly. 6. Prohibition relating to employment of women and young persons:- No women or young person shall be employed or permitted to work in any workroom involving exposure to benzene or substances containing benzene. 7. Labelling:- Every container holding benzene of substances containing benzene shall have the word “Benzene” and approved danger symbols clearly visible on it shall also display information on benzene content, warning about toxicity and warning about in flammability of the chemical. 8. Improper use of Benzene:- a) The use of benzene or substance containing benzene by workers for cleaning their hands or their work clothing shall be prohibited. b) Workers shall be instructed on the possible dangers arising from such misuse. 9. Prohibition of consuming food, etc. in work-room:- No workers shall be allowed to store or consume food or drink in the work room in which benzene or substances containing benzene are manufactured, handled or used. Smoking and chewing tobacco or pan shall be prohibited in such work-room. 10. Instructions as regards risk:- Every worker on his first employment shall be fully instructed on the properties of benzene or substances containing benzene which he has to handle and of the dangers involved. Workers shall also be instructed on the measures to be taken to deal with an emergency. 11. Cautionary notices:- Cautionary notices in the form specified in Appendix B and presented in the language easily read and understood by the majority of the workers shall be displayed in prominent places in the workrooms where benzene are manufactured, handled or used. 12. Washing and bathing facilities:- i) The following washing facilities and bathing facilities shall be provided and maintained in cleanly state and in good repair for the use of all persons employed in operations which involves manufacture, handling or use of Benzene or substances containing Benzene:- a) A wash-place under cover with clean towels, soap and nail brushes and with at least one stand pipe for every ten persons having constant supply of water. b) 50 per cent of the stand pipes provided under item (a) above to be located in bathroom. Water shall be made available during the working hours of the factory and for one hour thereafter. c) Clean towels to be provided individually to each worker and supply of hot water if so ordered by an Inspector. d) In addition to taps mentioned under item(a) one stand pipe in which warm water is made available to be provided on each floor. ii) Cloak room:- A cloak room with lockers for each worker, having two compartments one for street-clothing and one for work clothing, shall be provided. iii) Mess room:- A mess room furnished with tables and benches with means for warming food shall be provided and where a canteen or other proper arrangements exist for the workers to take their meals, the requirements of mess room may be dispensed with. 13. Medical examination:- a) Every worker who is to be employed in processes involving use of benzene or substances containing benzene, shall undergo- 241 i) a thorough pre-employment medical examination including a blood test for fitness for employment by a Medical Inspector/Certifying Surgeon. ii) periodical medical examination including blood test and other biological tests at intervals of every 6 months by the factory medical officer with the assistance of a laboratory. b) Certificates of pre-employment medical examination and periodical medical examination including test, shall be entered in a health Register in Form 29 and Medical Inspector of Factories/Certifying Surgeon may grant Certificate in Form 28 which shall be produced on demand by an Inspector. c) If the factory medical officer on examination at any time is of the opinion that any worker has developed signs or symptoms of benzene exposure, he shall make a record of his findings in the said register and inform the Manager in writing. On receipt of the information from the factory medical officer, the Manager of the factory shall send the worker so found exposed, to the Medical Inspector/Certifying Surgeon who shall after satisfying himself with the findings of the factory medical officer and conducting necessary examinations, issue orders of temporary shifting of the worker or suspension of the worker in the process. d) The medical examination shall be arranged by the occupier or manager of the factory and the worker so examined shall not bear any expenses for it. 13A. Medical facilities:- 1) The occupier or the factory shall appoint at least a part-time qualified medical practitioner, possessing MBBS degree and having a diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner so appointed shall be required to put in minimum four hours attendance on every working day in the ambulance-room for carrying out the duties specified in the following sub-paragraph (2). Provided that, in the cases factories employing less than 500 workers per day, the Chief Inspector of Factories may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) In addition to the duties specified in sub-paragraph(1) the medical practitioner so appointed shall perform the following duties, that is to say:- a) to maintain Health Register in Form 29. b) to undertake medical supervision of persons engaged in dangerous operations specified in rule 165 of these rules. c) to look after health, education ad-rehabilitation of sick, injured or affected workers. d) to carry out inspection of work-rooms where dangerous operations are carried out and to advice the management of the measures to be adopted for protection of health of the workers involved therein. 14. Exemption:- If in respect of any factory, the Chief Inspector is satisfied that owing to exceptional circumstances or infrequency of the process or for any other reason all or any of the provisions of this schedule are not necessary for the protection of employees, the State Government or subject to control of State Government the Chief Inspector may by a certificate in writing exempt such factory, from all or any of the provisions on such conditions as he may specify therein. Such certificate may at any time be revoked by Chief Inspector after recording his reason therefore. 242 APPENDIX A (Clause 3(b)) 1. Production of benzene. 2. Process where benzene is used for chemical synthesis. 3. Motor spirits (used as fuel). APPENDIX B (Clause 11) a) The hazards. :- i) Benzene and substances containing benzene are harmful. ii) Prolonged or repeated breathing of benzene vapours may result in act of chronic poisoning. iii) Benzene can also be absorbed through skin which may cause skin and other diseases. b) The preventive measures to be taken:- i) Avoid breathing of benzene vapours. ii) Avoid prolonged or repeated contact of benzene with the skin. iii) Remove benzene soaked or wet clothing promptly. iv) If any time you are exposed to high concentration of benzene vapours and exhibit the sign and symptoms such as dizziness, difficulty in breathing, excessive excitation and losing of consciousness, immediately inform your factory Manager. v) Keep all the containers of benzene closed. vi) Handle, use and process benzene and substances containing benzene carefully in order to prevent their spillage on floor. vii) Maintain good house keeping. c) The protective equipment to be used:- i) Use respitatory protective equipment in places where benzene vapours are present in high concentration. ii) In emergency use self-generating oxygen mask or oxygen or air cylinder masks. iii) Wear hand gloves, aprons, goggles and gum-boots to avoid contact of benzene with your skin and body parts. d) The first aid measures to be taken in case of acute benzene poisoning:- i) Remove the clothing immediately if it is wetted with benzene. ii) If liquid benzene enters eyes, flush thoroughly for at least 15 minutes, with clean running water and immediately secure medical attention. iii) In case of unusual exposure to benzene vapour call a physician immediately. Until he arrives, do the following:- If the exposed person is conscious:- a) Move him to fresh air in open. b) Lay down without a pillow and keep him quiet and warm. If the exposed person in unconscious:- a) Lay him down preferably on the left side with the head low. b) Remove any false teeth, chewing gum, tobacco or other foreign objects which may be in his mouth. c) Provide him artificial respiration in case difficulty is being experienced in breathing. d) In case of shallow breathing or cyanosis (blueness skin, lips, ear, finger, nail, beds) he should be provided with medical oxygen or 243 oxygen carbon dioxide mixture. If needed he should be given artificial respiration. Oxygen should be administered by trained person only. Schedule XXI Process of extracting oils, wax and fats from vegetable and animal sources in Solvent Extraction Plants 1. Application:- This Schedule shall apply to factories in which the process of extraction of oil, wax and fats from oil-cakes, oil-seeds or any other material from vegetable and animal source is carried out in Solvent Extraction Plants. 2. Definition:- In this Schedule, unless the context otherwise requires,- a) ‘Competent person’ means a person who- i) is atleast a member or associate member of the Mechanical or Chemical Engineering Branch of the Institute of Engineers(India), or ii) is a member or associate member of the Indian Institute of Chemical Engineers, or iii) is a graduate of a recognized University in Chemical Engineering, and iv) possess a minimum ten years experience of design or construction of flammable process plants specially the Solvent Extraction Plants. Provided that the State Government or Chief Inspector subject to control of the State Government, may accept any other person as a Competent Person, if it or he is satisfied regarding suitability of qualifications and experience of that person. b) ‘plant’ means the Solvent Extraction Plants; c) ‘Preparatory Process’ means the operations involving the equipment used for the preparation of the material for solvent extraction, d) ‘Solvent’ means an inflammable liquid such as pentane, hexane, heptable, mineral turpentine and the like. e) ‘Solvent Extraction Plant’ means any plant in which ;the process of extraction of oil, wax or fats from oil-cakes, oil seeds or any other material from vegetable and animal sources, by the use of solvents is carried on and includes the plant for recovery of the solvent. 3. Location and Lay-out:- 1) No plant shall be permitted within a distance of 30 metres from any residential locality or site for public utility. 2) The plant shall not be put into commission unless it is certified by a Competent Person that the plant, machinery and its other equipment are designed, fabricated and erected according to the best known practices pertaining to the process and the said certificate is submitted to the Chief Inspector, atleast one month before the commissioning of the plant. 3) A 1.5 metres high continuous wire fencing shall be provided around the plant, upto a minimum distance of 15 metres from the plants. 4) Boilers Houses and other buildings where open flame processes are carried on shall be located at least 30 metres away from the plant. 5) If godowns and buildings where preparatory processes are carried on are located at a distance of less than 30 metres from the plant, these shall be located at least 15 metres away from the plant, and 1.5 metres high continuous barrier wall of non-combustible materials shall be erected at a distance of not less than 15 metres from the plant 244 so that it extends to at least 30 metres of vapour travel around its ends from the plant to the possible source of ignition. Provided that, the existing units may be exempted from any of the provisions of this paragraph on such conditions as the State Government may deem fit. 4. Electrical Installations:- 1) All electrical meters, wirings and other electrical equipments installed or housed in the plant shall be of flame-proof constructions. 2) All metal parts of the plant and building including various tanks and containers where solvents are stored or are present and all parts of electrical equipments not required to be energized shall be properly bonded together and connected to earth so as to avoid accidental rise in the electrical potential of such parts above the earth potential. 5. Prohibition relating to smoking:- Smoking or carrying any source of ignition shall be strictly prohibited within a distance of 30 metres from the plant. For this purpose ‘NO SMOKING’ signs shall be permanently displayed in the area of the plant. 6. Precautions against friction:- 1) All the hand-tools required to be used in the plant shall be of non-sparking type. 2) No machinery or equipment of the plant shall be belt driven. Provided that, the plants existing prior to the date of commencement of these rules may continue with belt drives if the belts are of anti-static type and, in the opinion of a Competent Person, a proper earthing arrangement is made. 3) No person shall be allowed to enter and work in the plant if he is wearing clothes made of nylon or such other fibres which can generate static electrical charge, or if he is wearing footwear which is likely to cause sparks by friction. 7. Fire-fighting apparatus:- 1) Adequate number of portable fire extinguishers suitable for use against flammable liquid shall be provided in the plant. 2) Anautomatic water spray sprinkler system on a wet-pipe or open head defuse system with sufficient supply of storage water shall be provided over the plant area throughout the building in which the plant is housed. 3) This requirement shall be in addition to the requirements under any other provisions of the Tripura Factories Rules, 1997 regarding fire fighting apparatus and water supply. 8. Precautions against power failure:- Provisions shall be made any other provisions of steam in the event of power failure and also for emergency over-head water supply for feeding water by gravity to condensors for atleast half an hour which shall come into the play automatically with the power failure. 9. Magnetic Separators:- Oil cake shall be fed to the extractor by conveyor through a hopper, and magnetic separator shall be provided to remove any pieces of iron during its transfer. 10. Venting:- 1) Tanks containing solvents shall be projected with emergency venting to relieve excessive internal pressure in the event of fire. 2) All emergency relief vents shall terminate atleast 6 metres above the ground and be so located that vapours will be directed away from the plant. 245 11. Waste Water:- process waste water shall be passed through flash evaporator to remove any solvent before it is discharged into a sump which shall be located within the fenced area but shall not be closer than eight metres to such fence. 12. Ventilation:- The shed for the plant shall have adequate natural ventilation and if it is housed in building having ventilation which in the opinion of the Inspector, is inadequate, atleast six air changes per hour shall be ensured by mechanical means. 13. House Keeping: - 1) Solvent shall not be stored in an area covered by the plant except in quantities not exceeding 5 litres, which shall be stored in suitable safety cans. 2) Waste materials such as oily rag, other waste and absorbents used to wipe off solvents, oil and grease in the plant shall be deposited in suitable containers and removed from the premises at least once a day. 3) Premises where the Solvent Extraction process is carried on and the outer area within 15 meters from it shall be kept free from any combustible materials and any spills or oils or solvent shall be cleared up immediately. 14. Examination and repairs:- 1) a) The plant shall be examined by the competent person to determine any weakness or corrosion and wear, once in every twelve months. The Competent Person shall then furnish a report of such examination to the Inspector, with his recommendations as to whether the plant is in safe condition to work and the measures, if any, which in his opinion are necessary to be taken and the time by which such measures shall be taken, so as to ensure that the plant and equipment can be used without any danger to the workers in the factory. b) If any defects which are causing or likely to cause imminent danger to the life or safety of the workers working on such plant are found by the Competent Person, the Competent Person shall immediately submit a report to that effect to the Inspector and chief Inspector of Factories, standing therein the measures which, in his opinion, are necessary to ensure safety to the workers. When the necessary repairs are carried out, a copy of certificate by Competent Person that the plant has been repaired to his satisfaction shall be forwarded to the Inspector. 2) The plant shall be purged with inert gas or steam before opening for cleaning or repairs and before introducing solvent after repairs. 15. Operating Personnel:- 1) The plant shall be under an overall supervision of a qualified person who shall atleast be a graduate of a statutory University of Chemical Engineering or Technology with specialized knowledge of oils and fats with minimum 5 years experience in Solvent or Flammable. 2) The plant machinery or equipment shall be in the charge of operators who have been trained and made thoroughly conversant to operate the plant so certified by the qualified person referred to Clause(1). 16. Employment of young persons:- No women or young persons shall be employed in the plant. 17. Vapour Detection:- A flame-proof and portable combustible gas indicator or any other type of gas indicator as the Chief Inspector of Factories, may, subject to the control of the State Government, approve as safe and suitable for the purpose, shall be provided and maintained in good working order. A schedule of routine 246 sampling of atmosphere at various location as approved by the Competent Person shall be drawn out and entered in a register maintained for the purpose. 18. Additional provisions for batch-extractors:- The following further provisions shall apply to cater type extractor, namely:- a) When the Solvent is removed from batch extractors by vacuum, vacuum gauges shall be provided and tests shall be carried out to ensure that minimum vacuum of 650 mm (26”) mercury is obtained and maintained steadily for a minimum period of 30 minutes before the extractor is allowed to be opened for discharge of cake or for persons to enter. b) When, on opening the doors of a batch extractor, the extracted meal cannot be dislodged from the extractor freely, the doors shall be closed and the material reheated till the meal dislodges freely from the extractor. c) Where solvent is removed by steam heating, the presence of the Solvent shall be tested at the vent provided on the top of the vessel before opening the vessel. d) A log-book of operations with the following particulars shall be maintained and made available on demand to the Inspector:- i) Vacuum gauge reading for each charge. ii) testing of continuity of electrical bonding and earthing system. iii) loss of solvent every 24 hours or loss per tonne of raw materials used. 19. Exemption :- If, in respect of any plant, the Chief Inspector is satisfied that owing to exception circumstances or for any other reasons, all or any of the provisions of this Schedule are not necessary for the protection of the persons employed in the plant, he may by a certificate in writing exempt such factories from all or any of the provisions on such conditions as he may specify therein. Such certificates may at any time be revoked by the Chief Inspector without assigning any reasons. Schedule XXII Manufacture or Manipulation of Carcinogenic Dye Intermediates. 1. Application:- This Schedule shall apply in respect of all factories or any part thereof where processes in which the prohibited substances and controlled substances mentioned in paragraphs 3 and 4 respectively, are used, handled, manufactured, formed or dried, and the processes incidental thereto in the course of which these substances are formed, are carried on. The processes indicated in this paragraph shall hereinafter be referred to as “the said processes” and such a reference shall mean any or all the processes described in this paragraph. 2. Definitions:- For the purpose of this Schedule unless the context otherwise requires:- a) “Controlled Substances” means chemical substances mentioned in paragraph 4 of this Schedule. b) “Efficient Exhaust Draught” means localized ventilation effected by mechanical means for the removal of gas, vapour, dust or fume so as to prevent them from escaping into the air of any place in which fails to remove smoke generated at the point where such gas, vapour, fume or dust originate. c) “First Employment” means first employment in the said processes and also reemployment in such processes following any cessation of employment for a continuous period exceeding three calendar months; d) “Prohibited Substances” means chemical substances mentioned in paragraph 3 of the Schedule. 247 3. Prohibited substances:- For the purpose of this Schedule, the following chemical substances shall be classified as “Prohibited substances” except when these substances are present or are formed as a by-product of a chemical reaction in a total concentration not exceeding one per cent; a) Beta-naphthylamina and its salts. b) Benzidine and its salts. c) 4-amino diphenyl and its salts, d) 4-nitro diphenyl and its salts, and e) any substance containing any of these compounds. 4. Controlled Substances:- For the purpose of this Schedule, the following chemical substances shall be classified as controlled substances namely :- a) Alpha naphthylamine or alphanaphthylamine containing not more than one percent of betanaphthylamine either as by-product of chemical reaction or otherwise, and its salts. b) Ortho-tolidine and its salts. c) Dianisidine and its salts. d) Dichlorobenzidine and its salts. e) Auramine. f) Magneta. 5. Prohibition of employment:- No person shall be employed in the said process in any factory in which any prohibited substance is formed, manufactured, processes, handled or used except as exempted by the Chief Inspector as stipulated in paragraph 26. 6. Requirements for processing or handling controlled substances:- 1) Wherever any of the controlled substances referred to in paragraph 4 are formed, manufactured, processed, handled, or used, all practical steps shall be taken to prevent inhalation, ingestion or absorption of the said controlled substance, by the workers while engaged in processing that substance and its storage or transport within the plant, or in cleaning or maintenance of the concerned equipment, plant, machinery and storage areas. 2) As far as possible all operations shall be carried out in a totally enclosed system. Wherever such enclosure is not possible, efficient exhaust draught shall be applied at the point where the controlled substances are likely to escape into the atmosphere during the process. 3) The controlled substances shall be received in the factory in tightly closed containers and shall be kept so except when those substances are in process or in use. The controlled substances shall leave the factory only in tightly closed containers of appropriate type. All the containers shall be plainly labeled to indicate the contents. 7. Efficient exhaust draught:- Unless the manufacturing process is completely enclosed so as not to give off dust or fume it shall be carried on without the use of an efficient exhaust draught when any controlled substance, :- a) is introduced into a tank hopper machine or container or filled into cartridge; or b) is ground, crushed, mixed, sieved or blended. 8. Personal protective equipment:- 1) The following items of personal protective equipment shall be provided and issued to every worker employed in the said processes:- a) long trousers and shirts or overalls with full sleeves and head coverings. The shirt or overall shall cover the neck completely. b) Rubber-gum-boots. 248 2) The following items of personal protective equipment, shall be provided in sufficient numbers for use by workers employed in the said processes when there is danger of injury during the performance of normal duties or in the event of emergency; a) Rubber hand-gloves. b) Rubber aprons. c) Airlines respirators or other suitable respiratory protective equipment. 3) It shall be the responsibility of the manager to maintain all items of personal protective equipment in a clean and hygienic condition and in good state of repair. 9. Prohibition relating to employment of women and young persons:- No women or young persons shall be employed or permitted to work in any room in which the said processes are carried on. 10. Floors of work room.:- The floor of every work room in which the said processes are carried on shall be:- a) smooth and impervious to water without using asphalt or tar in the composition of the floor. b) maintained in a good state of repair. c) with a suitable slope for easy draining and provided with gutters, and d) thoroughly washed daily with the drain water being led into a sewer through a closed channel. 11. Disposal of empty container:- 1) Empty containers used for holding or staring controlled substances shall be thoroughly cleaned of their contents and treated with an inactivating agent before being discarded. 2) Empty non-metallic containers used for holding controlled substances shall be burnt. 12. Manual handling:- controlled substances shall not be allowed to be mixed, filled, emptied or handled except by means of a scoop with a handle. Such scoop shall be thoroughly cleaned daily. 13. Instructions regarding risk.:- Every worker on his first employment in the said processes shall be fully instructed on the properties of the toxic chemicals to which he is likely to be exposed and of the dangers involved and the precautions to be taken. Workers shall also be instructed on the measures to be taken to deal with an emergency. 14. Cautionary placards:- Cautionary placards in the form specified in the Appendix to this Schedule and printed in the language of the majority of the workers employed in the said processes shall be affixed in prominent places frequented by them in the factory, where the placards can be easily and conveniently read. Arrangements shall be made by the manager to instruct periodically all such workers regarding the precautions contained in the cautionary placards. 15. Medical Examinations:- 1) Every worker employed in the said processes shall be examined by a Medical Inspector of Factories or a Certifying Surgeon within 14 days of his first employment. Such examination shall include tests which the Medical Inspector of Factories or Certifying Surgeon may consider appropriate and shall include exfoliative cytology of the urine. No worker shall be allowed to work after 14 days of his first employment in the factory unless certified fit for such employment by the Medical Inspector of Factories or Certifying Surgeon. 249 2) Every worker employed in the said processes shall be reexamined by a Medical Inspector or Certifying Surgeon at least once in every six calendar months. Such examination shall include tests which the Medical Inspector or Certifying Surgeon may consider appropriate but shall include exfoliative cytology of the urine. 3) A person medically examined under sub-paragraph (1) shall be granted by the Medical Inspector or Certifying Surgeon a certificate of fitness in Form 28. Record of each re-examination carried out under sub-paragraph (2) shall be entered in the certificate. The certificates shall be kept in the custody of the manager of the factory. 4) The record of each examination carried out as referred to in sub-paragraph (1) and (2) including the nature and the results of the tests shall be entered by the Medical Inspector or Certifying Surgeon in the health register in Form 29. 5) The certificates of fitness and the health register shall be kept readily available for inspection by an Inspector. 6) If at any time the Medical Inspector or Certifying Surgeon is of the opinion that a person is no longer fit for employment in the said processes or in any other work on the ground that continuance therein would involve damage to his health, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in these documents shall also include the period for which he considers that the said person is unfit for work in the said processes or in any other work, as the case may be. 7) No person who has been found unfit to work as said in sub-paragraph(6) shall be re-employed or permitted to work unless the Medical Inspector of Factories or Certifying Surgeon after further examination, again certifies him to be fit for employment. 8) No worker shall be required to pay the charges or fees for the medical examination, re-examination or tests required to be done under this paragraph. Such charges or fees shall be paid by the occupier of the factory. 16. Medical facilities:- 1) The occupier of the factory shall appoint a qualified medical practitioner whose appointment shall be subject to confirmation by the Chief Inspector. The qualified medical practitioner so appointed shall be known as the appointed doctor. 2) The occupier shall provide:- a) for the purpose of medical examination which the appointed doctor wishes to conduct at the factory premises for his exclusive use, a room which shall be properly cleaned, adequately ventilated, lighted and furnished with a screen, a table (with writing material), chairs and facilities and instruments for such examination, and b) Oxygen gas cylinder with qualified personnel for its administration. 3) A record of medical examination and appropriate tests carried out by appointed doctor shall be maintained in a form approved by the Chief Inspector. 4) No person shall be employed in the said process unless he has been examined by using appropriate tests and found fit for the said process by the appointed doctor. 250 5) Persons examined in compliance with sub-paragraph(4) shall be re- examined by the appointed doctor at intervals of not more than 3 months or at such other intervals as may be directed in writing by the Chief Inspector and records of such examination shall be entered in the register provided under sub-paragraph(3). 6) If at any time, the appointed doctor is of opinion that any person is no longer fit for employment in the said process on the ground that continuance thereat would involve special danger to health, he shall make a record of his findings in the said register and intimate the manager in writing that the said person is unfit to work in the said process. 7) A person so found unfit by the appointed doctor shall be sent by the manager to the Medical Inspector of Factories or the Certifying surgeon with a report from the appointed doctor. The Medical Inspector of Factories or Certifying Surgeon after examination may suspend the said person from work in the said process. 8) No workers shall be required to pay the charges or fees for the medical examination, re-examination or tests required to be done under this paragraph. Such charges or fees shall be paid by the occupier of the factory. 17. Obligations of the workers:- It shall be the duty of the persons employed in the said processes to submit themselves for the medical examination including expoliative cytology of urine by the Medical Inspector of Factories or Certifying Surgeon or the appointed doctor as provided for under these rules. 18. Washing and bathing facilities:- i) The following washing and bathing shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the said processes, namely:- a) A wash place under cover having constant supply of water and provided with clean towels, soap and nail brush and with at least one stand pipe for every five such workers. b) 50 per cent of the stand pipes provided under clause(a) shall be located in bathrooms where both hot and cold water shall be made available during the working hours of the factory and for one hour thereafter. c) The washing and bathing facilities shall be in close proximity of the area housing the said processes but the same shall not be at a distance longer than 15 meters. Before the end of each shift one hour shall be allowed for bathing for each worker who is employed in the said processes and at least 10 minutes shall be allowed for washing before each meal in addition to the regular time allowed for meals. d) Clean towels shall be provided individually to each worker. e) In addition to the taps mentioned under clause(a), one stand pipe, in which warm water is made available, shall be provided on each floor. 2) Arrangement shall be made to wash factory uniforms and other work clothes every day. 19. Food, drinks, etc. prohibited in work-room:- No worker shall consume food, drink, pan, supari or tobacco or shall smoke on any premises in which the said processes are carried on and no worker shall remain in any such room during intervals of meals or rest. 251 20. Cloak room:- There shall be provided and maintained in a clean state and in good repair for the use of the workers employed in the said processes:- a) a cloak room with lockers having two compartments - one for street clothes and the other for work clothes, and b) a place separate from the locker room and the mess room for the storage of protective equipments provided under paragraph 7. The accommodation so provided shall be under the care of a responsible person and shall be kept clean. 21. Mess room:- There shall be provided and maintained for the use of workers employed in the said processes who remain on the premises during the meal intervals, a mess room which shall be furnished with tables and benches and provided with suitable means for warming food. Mess shall be placed under the charge of a responsible person and shall be kept clean. 22. Drying oven or stoves: 1) Every drying stove shall be efficiently ventilated to the out side air in such manner that hot air from the stove shall not be drawn into any work-room. 2) No person shall enter stove to remove the contents until a free current of air has been passed through it by mechanical means. 23. Restriction on age of persons employed:- No worker under the age of 40 years shall be engaged in the factory in the said processes for the first time after the date on which the Schedule comes into force. 24. Separation of processes: - The said process shall be carried on in a room or room which shall not directly communicate with any other room or rooms not having the said process except through a passage open entirely to outside atmosphere. 25. Testing of atmosphere etc.:- The prohibited substances in the atmosphere of the work-room where the manufacturing process is carried on shall be estimated once in every week and records of results of such estimation shall be made available when required by the Inspector. 26. Exemptions: - 1) The Chief Inspector may by a certificate in writing (which he may at his discretion revoke at any time) and subject to such conditions, if any, at may be specified therein, exempt any process in the course of which any of the prohibited substances is formed processed, manufactured, handled or used, from the provisions of paragraph 5 if he is satisfied that the process is carried out in a totally enclosed and hermetically sealed system in such a manner that the prohibited substance is not removed from the system except in quantities no greater then that required for the purposes of control of the process or such purposes as is necessary to ensure that the product is free from any of the prohibited substances. 2) The Chief Inspector may allow the manufacture, handling or use of benzidine hydrochloride, if he is satisfied that all the processes in connection with it are carried out in a totally enclosed system in such a manner that no prohibited substance other than benzidine hydrochloride is removed there from except in quantities no greater than that required for the purposes of control of the processes or such purposes as is necessary to ensure that the product is free from prohibited substances and that adequate steps are taken to ensure that benzidine hydrochloride is, except while not in a totally enclosed system, kept wet with not less than one part of water to two parts of benzidine hydrochloride at all times. 27. Exemptions-General:- If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this Schedule are not necessary for 252 the protection of the workers in the factory, the Chief Inspector may, by a certificate in writing (which he may at his discretion revoke at any time), exempt such factory of all or any of such provisions subject to such conditions, if any, as he may specify therein. APPENDIX Cautionary Placard/Notice 1. Dye intermedicates which are nitro or amino derivatives or aromatic hydrocarbons are toxic. You have to handle these chemicals frequently in this factory. 2. Use the various items of protective wear to safeguard your health. 3. Maintain scrupulous cleanliness at all times, thoroughly wash hands and feet before taking meals. It is essential to take a bath before leaving the factory. 4. Wash off any chemical falling on your body with soap and water. If splashed with a solution of the chemical remove the contaminated clothing immediately. These chemicals are absorbed through skin and are known to produce cyanosis. Contact the medical officer or appointed doctor immediately and get his advice. 5. Handle the dye intermediates only with long handled scoops, never with bare hands, 6. Alcoholic drinks should be avoided as they enhance the risk of poisoning by the chemicals. 7. Keep your food and drinks away from the place of work. Consuming food, drinks or tobacco in any from at the place of work is prohibited. 8. Serious effects from work with toxic chemicals may follow after many years. Great care must be taken to maintain absolute cleanliness of body, clothes, machinery and equipment. Schedule XXIII Highly Flammable Liquids and Flammable compressed Gases 1. Application:- These rules shall be applicable to all factories where highly flammable liquids or flammable compressed gases are manufacture, stored, handled or used. 2. Definition:- For the purpose of this schedule:- a) “highly flammable liquid” means any liquid including its solution, emulsion or suspension which when tested in a manner specified by sections 14 and 15 of the petroleum Act, 1934 (30 of 1934) gives off flammable vapours at a temperature less than 32 degree centigrade: b) “Flammable compressed gas” means flammable compressed gas as defined in section 2 of the Static and Mobile Pressure Vessels (Unfired) Rules, 1981 framed under the Explosive Act 1884. 3. Storage. 1) Every flammable liquid or flammable compressed gas used in every factory shall be stored in suitable fixed storage tank, or in suitable closed vessel located in a safe position under the ground, in the open or in a storeroom of adequate fire resistant construction. 2) Except as necessary for use, operation or maintenance, every vessels or tank which contains or had contained a highly flammable liquids or flammable compressed gas shall be always kept closed and all reasonably practicable steps shall be taken to contain or immediately drain off to suitable container any spill or leak that may occur. 253 3) Every container vessels, tank, cylinder, or store room used for storing highly flammable liquid or flammable compressed gas shall be clearly and in bold letters marked “ Danger- Highly flammable liquid” or “Danger-Flammable Compressed Gas.” 4. Enclosed System for conveying Highly Flammable Liquids:- Whenever it is reasonably practicable, highly flammable liquids shall be conveyed within a factory in totally enclosed system consisting of pipe lines, pumps and similar appliances from the storage tank or vessel to the point of use. Such enclosed systems shall be so designed installed, operated and maintained as to avoid leakage or the risk of spilling. 5. Preventing formation of flammable mixture with Air:- Wherever there is possibility for leakage or spill of highly flammable liquid or flammable compressed gas from an equipment, pipe line, valve, joint or other part of a system all practicable measures shall be taken to contain, drain off or dilute such spills or leakage as to prevent formation of flammable mixture with air. 6. Prevention of Ignition:- 1) In every room, work place or other location where highly flammable liquid or flammable combustible gas is stored, conveyed, handled or used or where there is danger of fire or explosion from accumulation of highly flammable liquid or flammable compressed gas in air, all practicable measures shall be taken to exclude the sources of ignition. Such precautions shall include the following:- a) All electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition; b) Effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent; c) No person shall wear or be allowed to wear any foot wear having iron or steel nails or any other exposed ferrous materials which is likely to cause sparks by friction; d) Smoking, lighting of matches, lighters or smoking materials shall be prohibited; e) transmission belts with iron fasteners shall not be used; and f) all other precautions, as are reasonably practicable, shall be taken to prevent initiation of ignition from all other possible sources such as open flames, frictional sparks, overheated surfaces of machinery or plant, chemical or physical- chemical reaction and radiant heat. 7. Prohibition of smoking:- No person shall smoke in any place where highly flammable liquid or flammable compressed gas is present in circumstances that smoking would give rise to a risk of fire. The occupier shall take all practicable measures to ensure compliance with this requirement including display of a bold notice indicating prohibition of smoking at every place where this requirement applies. 8. Fire Fighting:- In every factory where highly flammable liquid or flammable compressed gas is manufactures, stored, handled or used, appropriate and adequate means of fighting a fire shall be provided. The adequacy and suitability of such means which expression includes the fixed and portable fire extinguishing systems, extinguishing materials, procedures and the process of fire fighting, shall be to the standards and levels prescribed by the Indian Standards applicable, and in any case not inferior to the stipulations under Rule 82. 9. Exemptions:- If in respect or any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reasons all or any of the provisions of this schedule is not necessary for protection of the workers in the factory the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time exempt such ;factory from all or any of such provisions subject to such conditions, if any , as he may specify therein. 254 Schedule XXIV Operations involving High Noise Level 1. Application:- This schedule shall apply to all operations in any manufacturing process having high noise level. 2. Definitions:- For the purpose of this schedule:- a) “Noise” means any unwanted sound. b) “High Noise level” means any noise level measured on the A-weighted scale is 90 dB or above. c) “Decibel” means one-tenth of “Bel” which is the fundamental division of a logarithmic scale used to express the ratio of two specified or implied quantities, the number of “Bels” denoting such a ratio being the logarithmic to the base of 10 of this ratio. The noise level (or the sound pressure level) corresponds to a reference pressure of 2B ×10 neutons per square meter. 00002 or dynes per square centimeter which is the threshold of hearing, that is, the lowest sound pressure level necessary to produce the sensation of hearing in average healthy listeners. The decibel in abbreviated form is dB. d) “Frequency” is the rate of pressure variations expressed in cycles per second or hertz. e) “DBA” refers to sound level in decibels as measured on a sound level meter operating on the A-weighting net work with slow meter response. f) “A-weighting” means making graded adjustments in the intensities of sound of various frequencies for the purpose of noise measurement, so that the sound pressure level measured by an instrument reflects the actual response of the human ear to the sound measured. 3. Protection against noise:- 1) In every factory, suitable engineering control or administrative measures shall be taken to ensure, so far as is reasonably practicable, that no worker is exposed to sound levels exceeding the maximum permissible noise exposure levels specified in Tables 1 and 2. TABLE 1 Permissible Exposure in cases of continuous Noise Total time of exposure (continuous or a number Sound pressure Of short term exposures) per day, in hours Level in dBA 8 90 6 92 4 95 3 97 2 100 1½ 102 1 105 ¾ 107 ½ 110 ¼ 115 Notes:- 1) No. exposure in excess of 115 dBA is to be permitted. 2) For any period of exposure falling in between any figure and the next higher or lower figure as indicated in column 1, the permissible sound pressure level is to be determined by extrapolation on a proportionate basis. 255 TABLE 2 Permissible Exposure levels of Impulsive or Impact Noise. Peak sound pressure level in Db Permitted number of impulses or impact per day. ____________________________________________________________ 140 100 135 315 130 1,000 125 3160 120 10,000 Notes:- 1) No exposure in excess of 140 dB peak sound pressure level is permitted. 2) For any peak sound pressure level falling in between any figure and the next higher or lower figure indicated in column1, the permitted number of impulses or impacts per day is to be determined by extrapolation on a proportionate basis. 3) For any purposes of this schedule, if the variations in the noise level involve makima at intervals of one second or less, the noise is to be considered as continuous one and the criteria given in Table 1 would apply. In other cases, the noise is to be considered as impulsive or impact noise and the criteria given in Table 2 would apply. 4) When the daily noise exposure is composed of two or more periods of noise exposure at different levels their combined effect should be considered, rather than the individual effect of each. The mixed exposure should be considered to exceed the limit value if the Sum of the fractions C1 = C2 .................. C n exceeds unity. T1 T2 Tn Where the C1, C2, etc. indicate the total time of actual exposure at a specified noise level and T1,T2 etc, denote the time of exposure permissible at that level. Noise exposure of less than 90 dBA may be ignored in the above circulation. 5) Where it is not possible to reduce the noise exposure specified in sub-rule (i) by reasonably practicable engineering control or administrative measures, the noise exposure shall be reduced to the greater extent feasible by such control measures, and each worker so exposed shall be provided with suitable protectors so as to reduce the exposure to noise to the levels specified in sub-clause (i). 6) Where the ear protectors provided in accordance with sub-clause (2) and worn by a worker cannot still attenuate the noise reaching near his ear, as determined by subtracting the attenuation value in dBA of the ear protectors, concerned from the measured sound pressure level, to a level permissible under Table 1 or Table 2 as the case may be, the noise exposure period shall be suitable reduced to correspond to the permissible noise exposure specified in sub-clause (1). 7) a) In all cases where the prevailing sound level exceed for permissible levels specified sub-clause (1) there shall be administered an effective hearing conservation programme which shall include among other hearing conservation measures, pre-employment and periodical auditory surveys conducted on workers exposed to noise exceeding the permissible levels, and rehabilitation of such worker 256 either by reducing the exposure to the noise levels or by transferring then to places where noise levels are relatively less or by any other suitable means. 7) b) Every worker employed in areas where the noise exceeds the maximum permissible exposure levels specified in sub-clause (1) shall be subjected to an auditory examination by a Certifying Surgeon/medical Inspector of Factories within 14 days of his first employment and thereafter, shall be re-examined atleast once in every 12 months. Such initial and periodical examinations shall include tests which the Certifying Surgeon/Medical Inspector of Factories may consider appropriate, and shall include determination of auditory thresholds for pure tons of 125, 250, 500, 1000, 2000, 4000 and 8000 cycles per second. Schedule XXV Chemical Works Part I 1. Application: This schedule shall apply to all manufacture and processes incidental thereto carried on in chemical works. 2. Definition: For the purpose of this schedule- a) “Chemical Works” means any factory or such parts of any factory as are listed in appendix “A” to this schedule, b) “Efficient exhaust draught” means localised ventilation effected by mechanical or other means for the removal of gas, vapour, fume or dust to prevent it from escaping into the air of any place in which work is carried on. c) “Bleaching Powder” means the bleaching powder commonly called chloride of line; d) “chlorate” means chlorate or per chlorate; e) “caustic” MEANS HYDROXIDE OF POTASSIUM OR SODIUM; f) “Chrome Process” means the manufacture of chromate or bichromate of potassium or sodium, or the manipulation, movement or other treatment of these substances; g) “nitro” or amino process” means the manufacture of nitro or amino derivatives of phenol and of benzene or its homologues, and the making of explosives with the use of any of these substances; h) the term ‘permit to work’ system means the compliance with the procedures laid down under para 20 of part II. i) “toxic substances” means all those substances which when they enter into the human body, through inhalation or ingestion or absorption through skin, in sufficient quantities cause fatality or exert serious affliction of health, or chronic harmful effects on the health of persons exposed to it due to its inherent chemical or biological effects. In respect of substances whose TLV is specified in Rule 173, exceeding the concentration specified therein would make the substance toxic; j) “emergency” means a situation or condition leading to a circumstance or set of circumstances in which there is danger to the life or health of persons or which could result in big fire or explosion or pollution to the work and outside environment, affecting the workers or neighbourhood in a serious manner, demanding immediate action; k) “dangerous chemical reactions” means high speed reactions, run-away reactions, delayed reactions, etc. and are characterized by evolution of 257 large quantities of heat, intense release of toxic or flammable gases or vapours, sudden pressure build-up etc., 1) “manipulation” means mixing, blending, filling, emptying, grinding, sieving, drying, packing, sweeping, handling, using, etc.; m) “approved personal protective equipment” means items of personal protective equipment conforming to the relevant ISI specifications or in the absence of it, personal protective equipment, approved by the Chief Inspector. n) “appropriate personal protective equipment” means that when the protective equipment is used by the worker, he shall have no risk to his life or health or body; and o) “confined space” means any space by reason of its construction as well as in relation to the nature of the work carried therein and where hazards to the persons entering into or working inside exist or are likely to develop during working. PART II General Requirements Applying to all the works in Appendix A 1. Housekeeping:- 1) Any spillage of materials shall be cleaned up before further processing. 2) Floors, platforms, stairways, passages and gangways shall be kept free of any obstructions. 3) There shall be provided easy means of access to all parts of the plant to facilitate cleaning. 2. Improper use of chemicals:- No chemicals or solvents or empty containers containing chemicals or solvents shall be permitted to be used by workers for any purposes other than in the processes for which they are supplied. 3. Prohibition on the use of food, etc.:- No food, drink, tobacco, pan or any edible, item shall be stored or heated or consumed on or near any part of the plant or equipment. 4. Cautionary Notices and Instructions:- 1) Cautionary notices in a language understood by the majority of workers shall be prominently displayed in all hazardous areas drawing the attention of all workers about the hazards to health, hazards involving fire and explosion and any other hazard such as consequences of testing of material or substances used in the process or using any contaminated container for drinking or eating, to which the workers attention should be drawn for ensuring their safety & health. 2) In addition to the above cautionary notice, arrangement shall be made to instruct and educate all the workers including illiterate workers about the hazards in the process including the specific hazards to which they may be exposed to, in the normal course of their work. Such instructions and education should also deal with the hazards involved in unauthorized and unsafe practices including the properties of substances used in the process under normal conditions as well as abnormal conditions and the 258 precautions to be observed against each and every hazard. Further, an undertaking from the workers shall be obtained within 1 month of their employment and for old workers employed, within one month of coming into operation of the rules, to the effect that they have read the contents of the cautionary notices and instructions, understood them and would abide by them. The training and instructions to all workers and all supervisory personnel shall include the significance of different types of symbols and colours used on the labels stuck or painted on the various types of containers and pipe lines. 5. Evaluation and provision of safeguards before the commencement of process:- 1) Before commencing any process or any experimental work, or any new manufacture covered under Appendix ‘A’ the occupier shall take all possible steps to ascertain definitely all the hazards involved both from the actual operations and the chemical reactions including the dangerous chemical reactions. The properties of the raw materials used, the final products to be made, and any by-products derived during manufacture, shall be carefully studied and provisions shall be made for dealing with any hazards including effects on workers, which may occur during manufacture. 2) Information in writing giving details of the process, its hazards and the steps taken or proposed to be taken from the design stage to disposal stage for ensuring the safety as in sub-para (1) above should be sent to the Chief Inspector at the earliest but in no case less than 15 days before commencing manufacture, handling, or storage of any of items covered under Appendix ‘A’ whether on experimental basis, or as pilot plant or as trial production, or as large scale manufacture. 3) The design, construction, installation, operation, maintenance and disposal of the buildings, plant and facilities shall take into consideration effective safeguards against all the safety and health hazards so evaluated. 4) The requirements under the sub-para(1) to (3) shall not act in lieu of or in derogation to, any other provisions contained in any Act governing the work. 6. Authorised entry:- Authorised persons only shall be permitted to enter any section of the factory or plant where any dangerous operations or processes are being carried on or where dangerous chemical reactions are taking place or where hazardous chemicals are stored. 7. Examination of instruments are safety devices:- 1) All instruments and safety devices used in the process shall be tested before taking into use and after carrying out any repair to them and examined once in a month, by a competent person. Records of such tests and examinations shall be maintained in a register. 2) All instruments and safety devices used in the process shall be operated daily or as often as it is necessary to ensure its effective and efficient working at all times. 8. Electrical installations:- All electrical installations used in the process covered in Appendix ‘A’ shall be of an appropriate type to ensure safety against the hazard prevalent in that area such as suitability against dust, dampness, corrosion, flammability and explosivity etc. and shall conform to the relevant ISI specifications governing their construction and use for that area. 9. Handling and storage of chemicals:- 1) The containers for handling and storage of chemicals shall be of adequate strength taking into consideration the hazardous nature of the contents. 259 They shall also be provided with adequate labelling and colour coding arrangements to enable identification of the containers and their contents indicating the hazards and safe handling methods and shall conform to the respective ISI standards. The instructions given in the label shall be strictly adhered to. Damaged containers shall be handled only under supervision of a knowledgeable and responsible person and spillage shall be rendered innocuous in a safe manner using appropriate means. 2) The arrangements for the storage of chemicals including charging of chemicals in reaction vessels and containers shall be such as to prevent any risk of fire or explosion or formation of toxic concentration of substances above the limits specified in Rule 173. 3) Without prejudice to the generality of the requirements in sub-para (2) above, the arrangements shall have suitable ventilation facilities and shall enable the maintenance of safe levels in vessels and containers. Such arrangements shall also take into consideration, the type of flooring and the capacity of flooring and the compatibility requirements of substances with other chemicals stored nearby. 4) a) Storage of chemicals and intermediate products, which are highly unstable or reactive or explosive shall be limited to the quantities required for two months use. b) Whenever the quantities laid down in the above clause (a) are to be exceeded, the permission of the Chief Inspector shall be obtained. c) Notwithstanding anything contained in clause (a) and (b) above, the Chief Inspector may direct any factory carrying out processes covered in Appendix ‘A’ to further limit the storage of hazardous substances to quantities less than two months on considerations of safety. 5) Standby arrangements equal to the biggest container shall always be available to transfer the toxic substances quickly into the standby storage facility if any defect develops in any of the container resulting in the release of toxic substances. 6) Any storage facility constructed using non-metallic material such as Fibreglass Reinforced Plastics (FRP), all glass vessels etc., shall have adequate strength to withstand the stress, if any, exerted by the contents and shall be properly anchored, working platforms, access ladders, pipe lines etc. used in such storage facility shall be independently supported. 10. Facility for isolation:- The plant and equipment shall be so constructed and maintained as to enable quick isolation of plant or part of plant or equipment, with appropriate indication. One copy of the layout plan indicating the isolation facilities shall always be available with the security personnel, the maintenance and the health and safety personnel and these isolation facilities shall be checked for its effectiveness once in a month. 11. Personal protective equipment:- 1) All workers exposed to the hazards in the processes covered by this Schedule shall be provided with appropriate and approved type of personal protective equipment. Such equipment shall be in a clean, sterile and hygienic condition before issue. 2) The occupier shall arrange to inform, educate and supervise all the workers in the use of personal protective equipment while carrying out the job. 3) As regards any doubt regarding the appropriateness of any personal protective equipment, the decision of the Chief Inspector will be final. 12. Alarm Systems:- 260 1) Suitable and effective alarm systems giving audible and visible indications, shall be installed at the control room as well as in all strategic locations where process control arrangements are available so as to enable corrective action to be taken before the operational parameters exceed the predetermined safe levels or lead to conditions conductive for an outbreak of fire or explosion to occur. Such alarm systems shall be checked daily and tested every month at least once to ensure its performance efficiency at all times. 2) The Chief Inspector may direct such system to be installed in case of plants or processes where toxic materials are being used and spillage or leakage of which may cause wide spread poisoning in or around the plant. 13. Control of escape of substances into the work atmosphere:- 1) Effective arrangements such as, enclosure, or by pass, or efficient exhaust draught, maintenance of negative pressure etc., shall be provided in all plants, containers, vessels, sewers, drains, flues, ducts, culverts, and buried pipes and equipment, to control the escape and spread of substances which are likely to give rise to fire or explosion or toxic hazards during normal working and in the event of accident or emergency. 2) In the event of the failure of the arrangements for control resulting in the escape of substances in the work atmosphere immediate steps shall be taken to control the process in such a manner, that further escape is brought down to the safe level. 3) The substance that would have escaped into the work atmosphere before taking immediate steps as required in sub-para (2), shall be rendered innocuous by diluting with air or water or any other suitable agent or by suitably treating the substances. 14. Control of dangerous chemical reactions:- Suitable provision, such as automatic and or remote control arrangements, shall be made for controlling the effects of dangerous chemical reactions. In the event of failure of control arrangements automatic flooding or blanketing or other effective arrangements shall come into operation. 15. Testing, examination and repair of plant & equipment :- 1) All parts of plant, equipment and machinery used in the process which in the likely event of their failure may give rise to an emergent situation shall be tested by a competent person before commencing process and retested at an interval or two years or after carrying out repairs to it. The competent person shall identify the parts of the plant, equipment and machinery required to be tested as aforesaid and evolve a suitable testing procedures. In carrying out the test as mentioned above in respect of pressure vessels or reaction vessels the following precautions shall be observed, namely- a) before the test is carried out, each vessel shall be thoroughly cleaned and examined externally, and as far as practicable, internally also for surface defects, corrosion and foreign matter. Burning the process of cleaning and removal of sludge, if any, all due precautions shall be taken against fire or explosion, if such sludge is of pyropheric nature or contains spontaneously combustible chemicals; b) as soon as the test is completed, the vessel shall be thoroughly dried internally and shall be clearly stamped with the marks and figures indicating the person by whom testing has been done, and the date of test; and; 261 c) any vessel which fails to pass the test or which for any other reason is found to be unsafe for use shall be destroyed or rendered unusable under intimation to the Chief Inspector. 2) All parts of plant, equipment, machinery which in the likely event of failure may give rise to an emergent situation shall be examined once in a month by the competent person. 3) Records of testing and examination referred to in paragraphs (1) and (2) shall be maintained as long as that part of the plant, equipment and machinery are in use. 4) All repair work including alteration, modification and addition to be carried out to the plant, equipment and machinery shall be done under the supervision of a responsible person who shall evolve a procedure to ensure safety and health of persons doing the work. When repairs or modification is done on pipelines, and joints are required to be welded, butt welding of joints shall be preferred. Wherever necessary, the responsible person shall regulate the aforesaid work through a ‘permit to work system’. 16. Staging:- 1) All staging that is erected for the purpose of maintenance work or repair work or for work connected with entry into confined spaces and used in the processes included in Appendix ‘A’ shall be stable, rigid and constructed out of substantial material of adequate strength. Such staging shall conform to the respective Indian Standard specifications. 2) Staging shall not be erected over any closed or open vessel unless the vessel is so constructed and ventilated to prevent exposure of persons working on the stages. 3) All the staging constructed for the purpose of this para shall have appropriate access which are safe and shall be fitted with proper hand rails to a height of one metre and toe board. 17. Seating Arrangements:- The seating arrangements provided for the operating personnel working in processes covered in Appendix ‘A’ shall be located in a safe manner as to prevent the risk of exposure to toxic, flammable and explosive substances evolved in the work environment in the course of manufacture or repair or maintenance, either due to failure of plant and equipment or due to the substances which are under pressure, escaping into the atmosphere. 18. Entry into or work in confined spaces:- 1) The occupier of every factory to which the provisions of this schedule apply, shall ensure the observance of the following precautions before permitting any person to enter or work inside the confined spaces:- a) identify all confined spaces and the nature of hazards that are encountered in such spaces, normally or abnormally, and arrange to develop the most appropriate safeguards for ensuring the safety and health of persons entering into or working inside, the confined spaces; b) regulate the entry or work inside the confined spaces through a ‘permit to work system’ which should include the safeguards so developed as required under sub-clause (a) above; c) before testing the confined space for entry into or work, the place shall be rendered safe by washing or cleaning with neutralising agents; or purging with steam or inert gases and making adequate forced ventilation arrangements or such measure which will render the confined space safe; 262 d) shall arrange to carry out such tests as are necessary for the purpose by a competent person and ensure that the confined space is safe for the persons to enter or work. Such testing shall be carried out as often as is necessary during the course of work to ensure its continued safety; e) shall arrange to educate and train the personnel who would be required to work in confined spaces about the hazards involved in the work. He shall also keep in readiness the appropriate and approved personal protoctive equipment including arrangements for rescue, resurrection and first aid, and shall arrange supervision of the work at all times by a responsible and knowledgeable person. 2) The manager shall maintain a log of all entry into or work in, confined spaces and such record shall contain the details of persons assigned for the work, the location of the work and such other details that would have a bearing on the safety and health of the persons assigned for this work. The log book so maintained shall be retained as long as the concerned workers are in service and produced to the Inspector when demanded. 19. Maintenance work etc.:- 1) All the work connected with the maintenance of plants and equipment including cleaning of empty containers which have held hazardous substances used in the processes covered in this schedule, shall be carried out under ‘permit to work system’ employing trained personnel and under the supervision of responsible person, having knowledge of the hazards and precautions required to deal with them. 2) Maintenance work shall be carried out in such a manner that there is no risk to persons in the vicinity or to persons to pass by. If necessary, the place of such work shall be cordoned off or the presence of unconnected persons effectively controlled. 20. Permit to Work System: The permit to work system shall interalia includes the observance of the following precautions while carring out any specified work to be subjected to the permit to work system. a) All works subject to the permit to work system shall be carried out under the supervision of a knowledgeable and responsible person, b) all parts of plant or machinery or equipment on which permit to work system is carried out, shall remain isolated from other parts throughout the period of permit to work and the place of work including the parts of plant, machinery shall be rendered safe by cleaning, purging, washing etc. c) All work subject to the permit to work system shall have pre-determined work procedures which integrate safety with the work. Such procedures shall be reviewed whenever any change occurs in materials or equipments so that continued safety is ensured. d) Persons who are assigned to carry out the permit to work system shall be physically fit in all respects taking into consideration the demands and nature, of the work before entering into the confined space. Such person shall be adequately informed about the correct work procedures as well as the precautions to be observed while carrying out the permit to work system, e) Adequate rescue arrangements wherever considered necessary and adequate first aid, rescue and resurrection arrangements shall be available in good working condition near the place of work while carrying out the permit to work system for use in emergency. 263 f) Appropriate and approved personal protective equipment shall be used while carrying out the ‘permit to work system’. g) After completion of work subject to the ‘permit to work system’ the person responsible shall remove all the equipment and tools and restore to the original condition so as to prevent any danger while carrying out regular process. 21. Safety sampling personnel.:- The occupier shall ensure the safety of persons assigned for collecting samples by instructing them on the safe procedures. Such personnel shall be provided with proper and approved personal protective equipment, if required. 22. Ventilation:- Adequate ventilation arrangements shall be provided and maintained at all times in the process area where dangerous or toxic or flammable or explosive substances could be evolved. These arrangements shall ensure that concentrations, which are either harmful or could result in explosion, are not permitted to be built up in the work environment. 23. Procedures for meeting emergencies:- 1) The occupier of every factory carrying out the works covered in Appendix ‘A’, shall arrange to identify all types of possible emergencies that could occur in the processes during the course of work or while carrying out maintenance work or repair work. The emergencies so identified shall be reviewed every year. 2) The occupier shall formulated a detailed plan to meet all such identified emergencies including arrangements for summoning outside help for rescue and fire fighting and arrangements for making available urgent medical facilities. 3) The occupier shall send the list of emergencies and the details of procedures and plans formulated to meet the emergencies, to the Chief Inspector. 4) The occupier shall arrange to install distinctive and recognizable warning arrangements to caution all persons inside the plant as well as the neighbouring community, if necessary, to enable evacuation of persons and to enable the observance of emergency procedures by the persons who are assigned emergency duties. All concerned must be well informed about the warning arrangements and their meaning. The arrangements must be checked for its effectiveness every month. 5) Alternate power supply arrangements shall be made and interlocked with the normal power supply system so as to ensure constant supply of power to the facilities and equipment meant for compliance with requirements of paragraphs 10,11,12,13,14,18,22, and this paragraph of part II, part III, part IV and part V of this Schedule. 6) The occupier shall arrange to suspend the further process work in a place where emergency is established and shall forthwith evacuate all persons in that area except workers who have been assigned emergency duties. 7) All the employees of the factory shall be trained about the action to be taken by them including evacuation procedures during emergencies. 8) All emergency procedures must be rehearsed every three months and deficiencies, if any, in the achievement of the objectives shall suitably be corrected. 9) The occupier shall arrange to have ten percent of the workers trained in the use of First Aid Fire Fighting appliances and in the rendering of specific First Aid measures taking into consideration the special hazards of the particular process. 264 10) The occupier shall furnish immediately on request the specific chemical identity of the hazardous substance to the treating physician when the information is needed to administer proper emergency of first-aid treatment to exposed persons. 24. Danger due to effluents:- 1) Adequate precautions shall be taken to prevent the mixing of effluents from different processes and operations which may cause dangerous or poisonous gases to be evolved. 2) Effluents which contain or give rise in the presence of other effluents to poisonous gases shall be provided with independent drainage systems to ensure that they may be trapped and rendered safe. Part III Fire and Explosive Risks 1. Source of ignition including lighting installation: 1) No internal combustion engine and no electric motor or other electric equipment, and fittings and fixures capable of generating sparks or otherwise causing combustion or any other source of ignition or any naked light shall be installed or permitted to be used in the process area where there could be fire and explosion hazards. 2) All hot exhaust pipes shall be installed outside a building and other hot pipes or hot surface or surfaces likely to become hot shall be suitably protected. 3) The classification of work areas in terms of its hazard potential and the selection of electrical equipment or other equipment that could constitute a source of ignition shall be in accordance with the respective Indian Standard. 4) Where a flammable atmosphere may be prevalent or could occur, the soles of footwear worn by workers shall have no metal on them, and the wheels of trucks or conveyors shall be conductive type. 5) All tools and appliances used for work in this area shall be of non-sparking type. 6) Smoking in process areas where there are risks of fire and explosion shall be prohibited, and warning notices in the language understood by majority of workers shall be posted in the factory prohibiting smoking into specified areas. 2. Static Electricity: 1) All machinery and plant, particularly, pipe lines and belt drives, on which static charge is likely to accumulate, shall be effectively earthed. Receptacles for flammable liquids shall have metallic connections to the earthed supply tanks to prevent static sparking. Where necessary, humidity shall be regulated. 2) Mobile tanker wagons shall be earthed during filling and discharge, and precautions shall be taken to ensure that earthing is effective before such filling or discharge takes place. 3. Lightning Protection: Lightning Protection arrangement shall be fitted where necessary, and shall be maintained. 4. Process heating: The method of providing heat for a process likely to result in fire and explosion shall be as safe as possible and where the use of naked flame is necessary, the plant shall be so constructed as to prevent any escaping flammable gas, vapour, or dust coming into contact with the flame, or exhaust gases, or other sources likely to cause ignition. Wherever possible, the heating arrangement shall 265 be automatically controlled at a pre-determined temperature below the danger temperature. 5. Leakage of flammable Liquids: 1) Provision shall be made to confine by means of bund walls, dykes, sumps etc. possible leakage from storage vessels containing flammable liquids. 2) Waste material in contact with flammable substances shall be disposed off suitably under the supervision of knowledgeable and responsible person. 3) Adequate and suitable fire-fighting appliances shall be installed in the vicinity of such vessels. 6. Safety valves:- Every still and every closed vessel in which gas is evolved or into which gas is passed, and in which the pressure is liable to rise above the atmospheric pressure, shall have attached to it a pressure gauge, and a proper safety valve or other equally efficient means to relieve the pressure. These appliances shall be maintained in good condition. 7. Installation of pipe line etc.:- All pipelines carrying flammable or explosive substances shall be protected from mechanical damage and shall be examined by a responsible person once in a week to detect any deterioration or defects, or accumulation of flammable or explosive substances, and record kept of any defects found and repairs made. 8. Fire fighting systems:- 1) Every factory employing 500 or more persons and carrying out processes listed in Appendix ‘A’ shall provide:- a) Trained and responsible fire fighting squad so as to effectively handle the fire fighting and life saving equipment in the event of fire or other emergency. Number of persons in this squad will necessarily depend upon the size of risk involved, but in no case shall be less than 8 such trained persons to be available at any time. The squad shall consist of watch & ward personnel, fire pump-man and departmental supervisors and operators trained in the operation of fire & emergency services. b) Squad leaders shall preferably be trained in a recognized government institution and their usefulness enhanced by providing residence on the premises. c) Squad personnel shall be provided with clothing and equipment including helmets, boots and belts. 2) A muster roll showing the duties allocated to each member of the squad shall be prepared and copies supplied to each leader as well as displayed in prominent places so as to be easily available for reference in case of emergency. 3) The pumpman shall be thoroughly conversant with the location of all appliances. He shall be responsible for maintaining all fire fighting equipment in proper working order. Any defect coming to his notice shall be immediately be brought to the notice of squad leader. 4) As far as is practicable, the fire pump room and the main gate(s) of the factory be connected to all manufacturing or storing areas through telephone interlinked and placed in a convenient location near such areas. PART IV Risks of Toxic Substances 1. Leakage:- 266 1) All plants shall be so designed and constructed as to prevent the escape of toxic substance. Where necessary, separate buildings, rooms, or protective structures shall be used for the dangerous stages of the process and the buildings shall be so designed as to localize any escape of toxic substances. 2) Catch pits, bund walls, dykes, or other suitable safeguards shall be provided to restrict the serious effects of such leakages. Catch pits shall be placed below joints in pipelines where there is danger involved to maintenance and other workers from such leakage. 2. Drainage:- Adequate drainage shall be provided and shall lead to collection tanks specifically provided for this purpose wherein deleterious material shall be neutralised, treated or otherwise rendered safe before it is discharged into public drains or sewers. 3. Covering of vessels:- 1) Every fixed vessel or structure containing any toxic substance and not so covered as to eliminate all reasonable risk of accidental contact of any portion of the body of a worker, shall be so constructed as to avoid physical contact. 2) Such vessel shall, unless its edge is atleast 90 centimeters above the adjoining ground or platform, be securely fenced to a height of atleast 90 centimeters above such adjoining ground or platform. 3) Where such vessels adjoin and the space between them, clear of any surrounding brick or other work is either less than 45 centimeters in width or is 45 or more centimeters in width, but is not securely fenced in both sides to a height of atleast 90 centimeters, secure barriers shall be so placed as to prevent passage between them; Provided that sub-paragraph (2) of this paragraph shall not apply to - a) saturators used in the manufacture of sulphate of ammonia; and b) that part of the sides of brine evaporating pans which require raking, drawing or filling. 4. Continuous exhaust arrangement:- 1) Any process evolving toxic vapour, gas, fume and substance shall have efficient continuous exhaust draught. Such arrangement shall be interlocked in the process control wherever possible. 2) In the event of failure of continuous exhaust arrangement means shall be provided to automatically stop the process. 5. Work bench:- All the work benches used in processes involving the manipulation of toxic substances, shall be graded properly and shall be made of smooth impervious surface which shall be washed daily after the completion of work. 6. Waste disposal:- 1) There shall be provided a suitable receptacle made of non-absorbable material with tightly fitting cover for depositing waste material soiled with toxic substances and the contents of such receptacle shall be destroyed by burning or using other suitable methods under the supervision of a responsible person. 2) During the course of manufacture, whenever any batch or intermediate products having toxicity is rejected on considerations of quality, sufficient precautions shall be taken to render them innocuous or otherwise treat them or inactive them, before disposal. 3) The empty containers of toxic substances shall be cleaned thoroughly before disposal under the supervision of a responsible person. 267 PART V Special provisions 1) Special precautions for Nitro or Amino Processes:- 1) Unless the crystallised nitro or amino substances or any of its liquor is broken or agitated in a completely enclosed process so as not to give rise to dust or fume, such process shall be carried on under an efficient exhaust draught or by adopting any other suitable means in such a manner as to prevent the escape of dust or fume in the working atmosphere. 2) No part of the plant or equipment or implements which was in contact with nitro or amino compounds shall be repaired, or handled unless they have been emptied and thoroughly cleaned and decontaminated. 3) Filling of containers with nitro or amino compounds shall be done only by using a suitable scoop to avoid physical contact and the drying of the containers in the stove shall be done in such a manner that the hot and contaminated air from the stove is not drawn into the work room. 4) Processes involving the steaming into or around any vessel containing nitro or amino compounds or its raw materials shall be carried out in such a manner that the steam or vapour is effectively prevented to be blown back into the working atmosphere. 5) Suitable antidotes such as methylene blue injections shall always be available at designated places of work for the use during emergency involving the poisoning with nitro or amino compounds. 2. Special precautions for ‘chrome processes’:- 1) Grinding and sieving of raw materials in chrome processes shall be carried on in such a manner and under such condition as to secure effective separation from any other processes and under an efficient exhaust draught. 2) There shall be washing facilities located very near to places where wet chrome processes such as leaching, acidification, sulphate settling, evaporation, crystallisation, centrifugation or packing are carried out, to enable quick washing of affected parts of body with running water. 3) Weekly inspection of hand and feet of all persons employed in chrome process shall be done by a qualified nurse and record of such inspections shall be maintained in a form approved by the Chief Inspector. 4) There shall be always available at designated places of work suitable ointment such as glycerine, vaseline, etc. and water proof plaster in a separate box readily accessible to the workers so as to protect against perforation of nasal septum. 3) Special precautions for processes carried out in all glass vessels:- 1) Processes and Chemical reactions such as manufacture of vinyl chloride, benzyl chloride etc. which are required to be carried out in all glasses vessels shall have suitable means like substantial wire mesh covering to protect persons working nearby in the event of breakage of glass vessel. 2) Any spillage or emission of vapour from the all glass vessel due to breakage, shall be immediately inactivated or rendered innocuous by suitable means such as dilution with water or suitable solvents so as to avoid the risks of fire or explosion or health hazards. 4. Special precautions for processes involving chlorate manufacture:- 1) Crystallisation, grinding or packing of chlorate shall not be done in a place used for any other purpose and such places shall have hard, smooth and impervious surface made of non-combustible material. The place shall be thoroughly cleaned daily. 268 2) The personal protective equipment like overall, etc. provided for the chlorate workers shall not be taken from the place of work and they shall be thoroughly cleaned daily. 3) Adequate quantity of water shall be available near the place of chlorate process for use during fire emergency. 4) Wooden vessels shall not be used for the crystallization or chlorate or to contain crystallised ground chlorate. 1) Special precautions in the use of plant and equipments made from reinforced plastics:- a) All plant and equipments shall conform to appropriate Indian or any other National Standard. b) Care shall be taken during storage, transport, handling and installation of plant and equipments to avoid accidental damage. c) All plant and equipments shall be installed in such a way as to ensure that loads are dis_____________________ or as per the recommendations of the manufacturers. d) All pipe work shall be supported so that total loads local to the branches on the vessel or tank do not exceed their design values. e) After erection all plant and equipments shall be subjected to a pressure test followed by a thorough examination by a competent person. The test and examination shall be as per relevant standard. A certificate of test and examination by competent person shall be obtained and kept available at site. f) All plant and equipments shall be subjected to periodical test and examination and record maintained as per paragraph 15 in Part II of this Schedule. g) Plant and equipments during their use shall not be subjected to over filling or over loading beyond rated capacity. PART VI Medical Requirements 1. Decontamination facilities:- In all places where toxic substances are used in processes listed in Appendix ‘A’ the following provisions shall be made to meet an emergency:- a) fully equipped first aid box. b) readily accessible means of drenching with water persons, parts of body of persons, and clothing of persons who have been contaminated with such toxic and corrosive substances, and such means shall be as shown in the Table below:- No of persons No of drenching employed at any showers any time Upto 50 persons 2 51 to 100 3 101 to 200 3 + 1 for every 50 persons thereafter 201 to 400 5 + 1 for every 100 persons thereafter 401 and above 7 + 1 for every 200 persons thereafter c) a sufficient number of eye wash bottles filled with distilled water or 269 suitable liquid, kept in boxes or cupboards conveniently situated and clearly indicated by a distinctive sign which shall be visible at all times. 2. Occupational health centre: In all the factories carrying out processes covered in Appendix “A” there shall be provided and maintained in good order an occupational health centre with facilities as per scale laid down hereunder: 1) For factories employing upto 50 workers: a) the services of a qualified medical practitioner hereinafter known as Factory Medical Officer, available on a retainership basis, in his notified clinic near to the factory for seeking medical help during emergency. He will also carry out the pre- employment and periodical medical examinations as stipulated in paragraph 4 of this part. b) a minimum of five persons trained in first aid procedures, amongst whom at least one shall always be available during the working period. c) a fully equipped first aid box. 2) For factories employing 51 to 200 workers: a) The occupational health centre shall have a room having a minimum floor area of 15 sq.m., with floors and walls made of smooth, hard and impervious surface and shall be adequately illuminated, ventilated and equipped. b) A part-time factory Medical Officer will be in over all charge of the Centre who shall visit the factory minimum twice in a week and whose services shall be readily available during emergency. c) There shall be one qualified and trained dresser cum compounder on duty throughout the working period. d) A fully equipped first aid box. 3) For factories employing above 200 workers; i) There shall be one full-time Factory Medical Officer for factories employing upto 500 workers and one more medical Officer for every additional 1000 workers or part thereof; ii) an Occupational Health Centre having at least 2 rooms each with a minimum floor area or 15 sq. metre with floors and walls made of smooth and impervious surface and adequate illumination and ventilation as well as equipment as per the schedule annexed to the Rule. iii) there shall be one nurse, one dresser-cum-compounder and one sweeper-cum-ward boy through-out the working period. iv) the Occupational Health Centre shall be suitably equipped to manage medical emergencies. 3. Ambulance Van: 1) In every factory carrying out processes covered in Appendix ‘A’, there shall be provided and maintained in good condition, a suitably constructed and fully equipped ambulance van as per Appendix ‘C’ manned by a full- time driver-cum-mechanic and a helper, trained in first aid for the purposes of transportation of serious cases of accidents or sickness unless arrangements for procuring such facility at short notice during emergencies have been made with the nearby hospital or other places. The ambulance van shall not be used for any purpose other than the purpose stipulated herein and will always be available near the occupational Health Centre. 2) The relaxation to procure Ambulance Van from nearby places provided for in sub-para (1) above will not be applicable to factories employing more than 500 workers. 4. Medical Examination: 270 1) Workers employed in process covered in Appendix “A” shall be medically examined by a qualified medical practitioner in the following manner:- a) Once before employment, to ascertain physical fitness of the person to the particular job; b) Once in a period of 6 months, to ascertain the health status of all the workers in respect of occupational health hazards to which they are exposed; and in cases where in the opinion of the Factory Medical Officer it is necessary to do so at a shorter interval in respect of any workers. c) The details of per-employment and periodical medical examinations carried out as aforesaid shall be recorded in the Health Register in Form 29. 2) No person shall be employed for the first time without a certificate of fitness in Form 28 granted by the Factory Medical Officer. If the Factory Medical Officer declares a person unfit for being employed in any process covered in Appendix “A”, such a person shall have the right to appeal to the Inspector who shall refer the matter to the Certifying surgeon whose opinion shall be final in this regard. If the Inspector is also a Certifying Surgeon, he may dispose of the application himself. 3) Any findings of the Factory Medical Officer revealing any abnormality or unsuitability of any person employed in the process shall immediately be reported to the Certifying Surgeon who shall inturn, examine the concerned worker and communicate his findings to the occupier within 30 days. If the Certifying Surgeon is of the opinion that the worker so examined is required to be taken away from the process for health protection, he will direct the occupier accordingly, who shall not employ the said worker in the same process. However, the worker so taken away shall be provided with alternate placement unless he is in the opinion of the Certifying Surgeon, fully incapacitated in which case the worker affected shall be suitably rehabilitated. 4) A certifying Surgeon on his own motion or on a reference from an Inspector may conduct medical examination of a worker to ascertain the suitability of his employment in a hazardous process or for ascertaining his health status. The opinion of the Certifying Surgeon in such a case shall be final. The fee required for this medical examination shall be paid by the occupier. 5) The worker taken away from employment in any process covered in Appendix “A” may be employed again in the same process only after obtaining the Fitness Certificate from the Certifying Surgeon and after making entries to that effect in the Health Register. 6) The worker required to undergo medical examination under these rules and for any medical survey conducted by or on behalf of the Central or the State Government shall not refuse to undergo such medical examination. PART VII Additional Welfare Amenities 1. Washing facilities: 1) There shall be provided and maintained in every factory for the use of all the workers taps for washing, at the rate of one tap for every 115 persons including liquid soap in a container with tilting arrangements and nail brushes or other suitable means for effective cleaning. Such facilities shall be conveniently accessible and shall be kept in a clean and hygienic condition. 271 2) If washing facilities as required above are provided for women, such facilities shall be separate for them and adequate privacy at all times shall be ensured in such facilities. 2 Mess Room facilities: 1) The occupier of all the factories carrying out processes covered in Appendix “A” and employing 50 workers or more, shall provide for all the workers working in a shift mess room facilities which are well ventilated and provided with tables and sitting facilities alongwith the provisions of cold and hygienic drinking water facilities. 2) Such facilities shall include suitable arrangements for cleaning and washing and shall be maintained in a clean and hygienic conditions. 3. Cloakroom facilities:- 1) The occupier of every factory carrying out any process covered in Appendix ‘A’ shall provide for all the workers employed in the process cloak room facilities with lockers. Each workers shall be provided with two lockers, one for work clothing and another separately for personal clothing and the lockers should be such as to enable the keeping of the clothing in a hanging position. 2) The cloak room facilities so provided in pursuance of sub-para (1) shall be located as far as possible near to the facilities provided for washing in pursuance of para1(1). If it is not possible to locate the washing facilities the cloak room facilities shall have adequate and suitable arrangements for cleaning & washing. 4. Special Bathing Facilities: 1) The occupier of any factory carrying out the process covered under Appendix “B” shall provide special bathing facilities for all the workers employed and such facilities shall be provided at the rate of 1 for 25 workers and part thereof, and shall be maintained in a clean and hygienic condition. 2) The occupier shall insist all the workers employed in the processes covered in Appendix ‘B’ to take bath after the completion of the day’s or shift work using the bathing facilities so provided and shall also effectively prevent such of these workers taking bath in any place other than the bathing facilities. 3) Notwithstanding anything contained in sub-para (1) above, the Chief Inspector may require in writing the occupier of any factory carrying out any other process for which in his opinion bathing facilities are essential from the health point of view, to provide special bathing facilities. PART VIII 1. Duties of workers 1) Every worker employed in processes covered in Appendix ‘A’ and Appendix ‘B’ shall not make any safety device or appliance or any guarding or fencing arrangement, inoperative or defective and shall report the defective condition of the aforesaid arrangements as soon as he is aware of any such defect. 2) Before commencing any work, all workers employed in processes covered in Appendix ‘A’ shall check their workplace as well as the machinery, equipment or appliance used in the processes and report any mal-function or defect immediately to the supervisor of any responsible person of the management. 3) All workers shall co-operate in all respects with the management while carrying out any work or any emergency duty assigned to them in pursuance of this 272 schedule and shall always use all the personal protective equipments issued to them in a careful manner. 4) All workers employed in the processes covered in Appendix ‘A’ or Appendix ‘B’ shall not smoke in the process area or storage area. If special facilities are provided by the management only such facilities should be used. 5) All workers employed in the processes covered in Appendix ‘A’ shall not remain in unauthorised place or carry out unauthorised work or improvise any arrangements or adopt short cut method of misuse any of the facilities provided in pursuance of the Schedule, in such a manner as to cause risk to themselves as well as or to others employed. 6) The workers shall not refuse undergoing medical examination as required under these rules. PART IX Restrictions on the employment of young persons under 18 years of age and women. 1. The Chief Inspector may by an order in writing, restrict or prohibit the employment of women and young persons under the age of 18, in any of the processes covered in Appendix ‘A’ of this schedule on considerations of health and safety of women and young persons. 2. Such persons who are restricted or prohibited from working in the process due to the order issued in pursuance of sub-para (1) above shall be provided with alternate work which is not detrimental to their health or safety. PART X Exemptions 1. Power of exemption:- The State Government or subject to the control of the State government, the Chief Inspector may exempt from the compliance with any of the requirements of this Schedule partly or fully, any factory carrying out processes covered in Appendix ‘A’, if it is clearly and satisfactorily established by the occupier that the compliance with any of the requirement is not necessary to ensure the safety and health of persons employed suitable and effective alternate arrangements are available to any of the requirements covered in this schedule. Appendix ‘A’ Any work or that part of works in which- a) the manufacture, manipulation or recovery of any of the following is carried on:- i) sodium, potassium, iron, aluminium, cobalt, nickel, copper, arsenic, antimony, chromium, zinc, selenium, magnesium, cadmium, mercury, beryllium, and their organic and inorganic salts, alloys, oxidies and hydroxides; ii) Ammonia, ammonium hydroxide and salts of ammonium; iii) the organic or inorganic compounds of sulphurous, sulphuric, nitric, nitrous, hydrochloric, hydrofluoric, hydriodic, hydrosulphuric, hydrobromic, boric; iv) cyanogen compounds, cyanide compounds, cyanate compounds; v) phosphorous and its compounds other than organo phosphorous insecticides; vi) chlorine. b) hydrogen sulphide is evolved by the decomposition of metallic sulphides, or hydrogen sulphide is used in the production of such sulphides; 273 c) bleaching powder is manufactured or chlorine gas is produced in chlor-alkali plants; d) i) gas tar or coal tar or bitumen or shale oil esphalt or any residue of such tar is distilled or is used in any process of chemicals manufacture; ii) tar based synthetic colouring matters or their intermediates are produced; e) nitric acid is used in the manufacture of nitro compounds; f) explosives are produced with the use of nitro compounds ; g) aliphatic or aromatic compounds or their metallic and non metallic derivaties or substituted derivatives, such as chloroform, ethylene glycol, formaldehyde, benzyls chloride, phenol, methyl ethyl keytone peroxide, cobalt carbonyl, tungsten carbide etc, are manufactured or recovered. Appendix ‘B’ Concerning Special Bathing Accommodation in pursuance of para 4 of part IV. 3. Nitro or amino processes. 4. All chrome processes. 5. Processes of distilling gas or coal tar or processes of chemical manufacture in which tar is used. 6. Processes involving manufacture, manipulation, handling or recovery of cyanogen compound, cyanide compound, cyanate compounds. 7. Processes involving manufacture of bleaching powder or production of chlorine gas in chlor-alkali plants. 8. Manufacture, manipulation or recovery of nickel and its compounds. 9. All processes involving the manufacture, manipulation or recovery of aliphatic or aromatic compounds or their derivatives or substituted derivatives. Appendix ‘C’ Ambulance Ambulance should have the following equipments:- General - An wheeled stretcher with folding and adjusting devices; - Head of the stretcher must be capable of being tilted upward, - Fixed suction unit with equipments; - Fixed oxygen supply with equipments; - Pillow with case; - Sheets; - Blankets; - Towels; - Emesis bag; - Bed pan; - Urinal; - Glass. Safety equipment - Flares with life or 30 minutes; - Flood lights; - Flash lights; - Fire extinguisher dry powder type; 274 - Insulated gauntlets. Emergency care equipments Resuscitation - Portable suction - Portable oxygen unit; - Bag-valve-mask, hand operated artificial ventilation unit; - Airways; - Mouth bags; - Tracheotomy adaptors; - Short spine board; - I.V. Fluids with administration unit; - B.P. manometer; - Chug; - Stethoscope. - Immobilization;- - Long & short spine boards. Dressings - Cauze pads - 4” ×4”; - Universal dressing 10” ×36”; - Roll of aluminium foils; - Soft roller bandages 6” ×5” yards; - Adhesive tape in 3” roll; - Safety pins; - Bandage sheets; - Burn sheet. Poisoning - Syrup of Ipecac; - Activated charcoal; - Snake bite kit; pre-packeted in doses. - Drinking water. Emergency Medicines - As per requirement (under the advice of Medical Officer only) Schedule XXVI Manipulation of stone or any other material containing free silica. 1. Application:- This Schedule shall apply to all factories or parts of factories in which manipulation of stone or any other material containing free silica is carried on. 2. Definitions:- For the purpose of this schedule:- a) “manipulation” means crushing, breaking, chipping, dressing, grinding, sieving, mixing, grading or handling of stone or any other material containing free silica or any other operation involving such stone or material; b) “Stone or any other material containing free silica” means a stone or any other solid material containing not less than 5(five) percent by weight of free silica. 275 3. Precautions in manipulations:- No manipulation shall be carried out in a factory or part of a factory unless one or more of the following measures, namely:- a) damping the stone or other material being processed, b) providing water spray, c) enclosing the process, d) isolating the process, and e) providing localised exhaust ventilation. are adopted so as to effectively control the dust in any place in the factory where any person is employed, at a level equal to, or below the maximum permissible level for silica dust as laid down in ‘Table 2 appended to Rule 173. Provided that such measures as abovesaid are not necessary if the process or operation itself is such that the level of dust created and prevailing does not exceed the permissible level referred to. 4. Maintenance of floors:- 1) All floors or places where fine dust is likely to settle on and whereon any person has to work or pass shall be of impervious material and maintained in such condition that they can be thoroughly cleaned by a moist method or any other method which would prevent dust being airborne in the process of cleaning. 2) The surface of every floor of every work room or place where any work is carried on or where any person has to pass during the course of his work, shall be cleaned of dust once at least during each shift after being sprayed with water or by any other suitable method so as to prevent dust being airborne in the process of cleaning. 5. Prohibition relating to young persons:- No young person shall be employed or permitted to work in any of the operations, involving manipulation or at any place where such operations are carried on. 6. Medical facilities and records of examination and tests:- 1) The occupier of every factory to which the schedule applies shall:- a) employ a qualified medical officer for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector and b) Provide to the said medical officer all the necessary facilities for the purpose referred to in clause (a) 2) The record of medical examination and appropriate tests carried out by the said Medical Officer shall be maintained in a separate register approved by the Chief Inspector, which shall be kept readily available for inspection by the Inspector. 7. Medical examination by Certifying Surgeon:- 1) Every worker employed in the processes specified in paragraph 1, shall be examined by a Certifying Surgeon within 15(fifteen) days of his first employment. Such medical examination shall include pulmonary function tests and chest x-ray. No worker shall be allowed to work after (15) (fifteen) days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. 2) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every 12(twelve) months. Such examination shall, wherever the Certifying Surgeon considers appropriate, inclusive all tests as specified in sub-paragraph (1) except chest X-Ray which will be once in three years. 276 3) The Certifying Surgeon after examining a worker, shall issue a certificate of fitness in Form 28. The record of examination and re-examinations carried out shall be entered in the certificate and the certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under subparagraphs (1) & (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 4) The certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. 5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in subparagraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 8. Exemptions:- If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief Inspector may issue a certificate in writing, which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Schedule XXVII Fire Works Manufacture and Match Factories 1. Application: The provisions of this schedule shall apply to all manufactories and processes incidental thereto carried on in any fire works manufactory or a match works and shall be in addition to and not in derogation of any provisions of the Factories Act. 1948 and the Tripura Factories Rules, 1996 or of any other Act or Rules that are applicable to fire works manufactories and match factories. 2. Definition: a) “Fire Works Manufactory” means any factory or such part of any factory wherein the following chemicals or combination of chemicals and materials are being used for the manufacture of crackers, sparklers, caps, fuses, blasting powder and fire works: Salpetre; Pyrotechnic Alluminium Powder Barium Nitrate Charcoal Potassium Chloride Red Phosphorous Gum Dextrine Stronium Nitrate Magnesium Powder 277 Copper Coated Wires Steel fillings or Iron fillings G I Wire Gun Powder (Black Powder) b) “Match Works” means any establishment which manufactures safety matches or colour matches by the use of chemicals mentioned in clause (a). c) “Breathing Apparatus” means a device covering mouth or nose with necessary connections by means of which a person using it in a poisonous asphyxiating or irritant atmosphere breaths ordinary air or any other suitable apparatus approved in writing by the Chief Inspector in this behalf. 3. Buildings: a) The building of any fire works manufactory or match factory shall conform to the standards prescribed under the Indian Explosive Act, 1884. b) No building inside a fire works manufactory shall have a first floor at any time. c) In match works, provided with a first floor, there shall be 2 staircases leading from the first floor to the ground irrespective of the number of persons employed in the first floor and one of the staircases shall be of masonry construction or of non- inflammable materials; d) All doors shall open outwards and all the doorways shall be kept free from obstructions; e) All doors of workrooms shall not be less than 1.2 metres in width or less than 2 metres in height; f) The floors of all work rooms including mixing sheds shall be completely covered by a rubber sheet having a smooth surface and having a thickness of atleast 3 mm. If the floor cannot be covered by a single rubber sheet, more than one rubber sheet may be used, so that each sheet is overlapped by the other atleast 150 mm; and g) Mixing sheds shall be 30.5 metres away from all other sheds and be separated by baffle walls opposite each exit of the mixing shed. 4. House-keeping:- a) Every part of ways, works, machinery and plant shall be maintained in a clean and tidy condition; b) Any spillage of materials shall be cleaned without delay; c) Close platforms, passages and gangways shall be kept free of temporary obstructions. 5. Electrical Equipment:- a) If at any time, use of electricity is allowed in the factory, all leads, etc, shall be in conduits with flame-proof junctions; b) Electrical supply shall never be through a lamp even with a non- conducting handle. 6. Protective clothing:- a) Under no circumstances clothes made of artificial fibre like terelene, etc, be allowed inside the factory; b) All workers shall be supplied with asbestos aprons especially to cover the chest, gonads and thighs; c) Breathing apparatus shall be used in mixing sheds to avoid workers inhaling poisonous fumes in the event of an untoward reaction. 278 d) In mixing sheds where aluminium and magnesium powders are used “anti- stat” foot-wear to combat static electricity shall be supplied. e) All protective equipments shall be maintained in an efficient condition and also shall be maintained in a clean and hygienic condition. 7. Match Factory:- In match factories:- i) the residue of the head composition shall not in any way be mixed with the residue of the friction composition; ii) the rooms comprising the two mixing departments, namely, (a) head composition and (b) friction composition shall be entirely separated from each other and the drains from these two departments shall be kept entirely separate; iii) rubbish containing the residues of the head composition and friction composition shall be kept and burnt separately; iv) department in which completed matches (matches with heads on) are stored shall be separated from all other departments by means of fire-proof walls and doors providing adequate means of escape in case of fire; Provided that the Chief Inspector may, subject to such conditions, as he may deem necessary, exempt any factory in existence on the first January 1935, from the provisions of this clause; exempt any factory in existence on the first January 1935, from the provisions of this clause; v) Splints, veneers and other materials in excess of the quantity required for the day’s manufacture shall be kept in separate rooms of the factory where no manufacturing process is carried on. No manufactured material shall be stored anywhere in the factory compound for more than 5(five) days after the manufacture except in the storage godowns; Provided that nothing contained in this clause shall apply to splints and veneers in cases stored in peeling and box making departments; vi) Store room for matches shall be entirely separated by fire proof walls from the buildings used for manufacture; and vii) The racks in the dipped splints room shall have sides, top and the rear part provided with non-inflammable materials. 8. Precautions to be taken in connection with manufacture of fuses used in crackers, etc:- a) Bundles of fuses shall be handled by carrying and not dragging them on the floor; b) Drying of fuses after wrapping shall be carried out on platforms away from workrooms; c) Cutting shall be done by experienced workers employed only for this purpose and under proper supervision; d) Cutting shall be done on a large masonry platform covered with a tarpaulin and kept free from grit and pebbles; e) Cutting shall be done on a raised platform so that workers can work standing, Cutting must be done by placing the fuse on wooden sleepers kept over blocks of wood. Brick shall not be used beneath the wooden reapers; and f) Workers, while on dangerous operations, shall not wear clothing seqn with ferrous or steel buttons, buckles or attachments. They shall not carry on their persons, iron knives, keys, etc. 9. Employment of women and children:- Women workers and young persons below 18 (eighteen) years of age shall not be employed on operations where chemicals are mixed and where fuses are cut. 10. General: 279 a) No person other than a factory worker and/or an inspecting officer or others connected with the manufacturing process shall be allowed to enter the working area. b) Cardboard containers and trays without steel nails shall be used for storage and day to day working purposes. c) During the manufacture of fuses only brass or non ferrous knives shall be used and drying of fuses shall be away from all workrooms. d) Door mats shall be provided outside the workrooms and near all drying platforms and where fuses are cut for the workers to clean their feet. e) At no time, mixing materials shall exceed the quantity that is required for the manufacture of mixing for half an hour operation only. f) For filling up chemicals in the inner tube of crackers, only aluminium or plastic rings shall be used and not galvanized iron rings. g) Buckets, containers, hoops, locks, nails, screws bolts, nuts, knives, scissors, etc made up of iron shall not be used within the factory premises. h) Wooden racks without iron nails shall be used for drying paper cap sheets, in amorcess factories. i) Wooden racks used for drying paper sheets shall be provided with asbestos or other fire resistant sheets on the three sides leaving the front side open. j) Dried paper cap sheets shall be carried in wooden trays with four compartments (partitioned) each compartment (partition) carrying a single sheet. k) Each manufacturing shed of a fire works shall have atleast two doors facing each other. The doors provided to the worksheds of adjacent rows shall not face each other. l) Not more than four persons shall be employed or allowed at any one time in any one building in which explosive is being manufactured. 11. Display of Notices: The following notices in the local language understood by the majority of workers shall be displayed at a conspicuous place in the factory. Smoking is strictly prohibited. 1) No one shall carry matches or other igniting materials into the factory. 2) No worker shall be in a workroom or area where no work has been assigned to him. 3) If anything untoward happens in any shed all workers shall dash to the gates which serve as outgates of the factory and in no circumstances be curious to see what has happened in the affected shed. 4) Any spillage of materials should be cleaned without any delay. 5) Wearing of clothes made of artificial fibre like terene, terelene etc is prohibited. Clothing sewn with ferrous or steel buttons or buckles or attachments should not be worn. 6) Foot wears with iron nails should not be used. 7) Workers should not carry with themselves iron knives and iron keys etc. 12. First Aid Boxes: a) The materials required under Rule 124 shall be kept in the First Aid Box. In addition , four stretchers shall be available for every 20 (twenty) persons employed in the premises. b) Adequate amount of burn dressings and 24 ounces of coconut oil be used as the first remedy for burns shall be kept in the First Aid Box. c) Persons who are in charge of First Aid Boxes shall be those who possess the certificate granted by the St. John’s Ambulance Association for rendering first aid. 13. Exemption: If the Chief Inspector is satisfied in respect of any factory or any process that, owing to the special conditions or special methods of work or by 280 reason of the Frequency of the process or for other reason the application of all or any of the provisions of the schedule to the Factory or process, or for the persons employed in such factory or process is not necessary, he may by order in writing exempt such factory or part of the factory or process or any part of the factory or person from all or any of these provisions subject to such conditions as he may deem expedient to ensure safety and health of the workers. The chief Inspector may at any time in his discretion revoke such order without assigning any reason. Schedule XXVIII Composing, Printing, Binding and Processes and/or Operations incidental thereto 1. Application: This schedule shall supply to all factories with any or all of the types of facilities available for Composing, Printing, Binding and Processes and/or Operations incidental thereto. 2. Definitions: “Video Display Terminal (VOT)” means an alphanumeric or graphic display screen regardless of display process employed. 3. .VDT’s check/inspection: The occupier shall ensure that: a) every VDT installed carry a certificate from the manufacturer that this model has been approved by the competent authority for radiation protection and the emission level at 5 cm from the surface is below 0.5 mrem/h. b) shielding of scan transformers are effective. c) the VDT is maintained in such a way that its use is safe and without risk to health; and d) wherever a number of VDTs are in use, they shall be so distributed and located that their combined effect is not hazardous and their emission levels are monitored to keep the levels within permissible limits. 4. Provision for correction glasses: The occupier shall provide at his cost correction glasses of the appropriate power to workers employed on VDTs who are using power glasses for vision. 5. Special Provisions for pregnant women: Necessary measures like provision for proper work station shall be made so that pregnant women employees perform duties without excessive discomfort and fatigue. 6. Control of Ultraviolet Rays, Ozone and fumes in work atmosphere: Whatever ultraviolet rays are used, such as for drying, they shall be properly shielded by interlock guards and the units are well ventilated. 7. Collection, Development, Dissemination, Disclosure etc, for information: No chemical shall be stored or used in any process or operation unless full information regarding the hazards involved and the required safety measures are collected ar developed and made known to Chief Inspector and disseminated to workers. 8. Medical Examination: a) Medical examination of workers shall be carried out as prescribed under Rule 165 (4). b) Pre-employment: Optahalmological examination shall be carried out for each worker before initial employment on VDT operation to identify any 281 diseases of the eye which pre-disposes the individual to visual disorders including photo sensitive epilepsy while using VDT. c) Necessary annual opthalmological examination shall be carried out for each worker employed on VDT. d) Any worker who complains of visual discomfort or visual disorder shall be opthalmologically re-examined immediately. Schedule XXIX Processing of Cashew nut 1. Application:- This schedule shall apply to all factories in which roasting, scrubbing and shelling of cashewnuts or extracting oil from cashewnuts or cashewnut shells are carried on. 2. Prohibition of employment of women and young persons:- No women or young person shall be employed in any of the processes specified in paragraph 1 except in shelling of roasted cashewnuts. 3. Protective clothing and equipment:- The Occupier shall provide and maintain for the use of all persons employed in reasting and scrubbing of cashewnuts or extracting oil from cashewnuts or cashewnut shells- a) a suitable rubber or washable leather gloves: b) suitable type of impervious aprons with sleeves to cover body down to knees and shoulders; and c) suitable type of footwear to afford protection to feet and legs against cashewnut oil; and for the workers employed in cashewnut shelling, either d) a protective ointment containing 10% of shellac, 55% of alcohol, 10% of sodium perrborate, 5% of carbitol and 20% talc; or e) sufficient quantity of kaolin and coconut oil; and f) any other material or equipment which the Chief Inspector may deem to be necessary for the protection of the workers. 4. Use of protective clothing and equipment:- Every person employed in processes specified in paragraph 1 shall make use of protective clothing and equipment supplied and arrangements shall be made by the occupier to supervise its use, maintenance and cleanliness. 5. Disposal of shells, ashes, or oil of cashewnut:- 1) Shells, ashes or oil of cashewnut shall not be stored in any room in which workers are employed and shall be removed at least twice a day to any pit or enclosed place in the case of shells and ashes and to closed containers kept in a separate room in the case of oil. 2) No worker shall be allowed to handle shells or oil of cashewnuts without using the protective clothing or equipment provided under paragraph 3 above. 6. Floors of workrooms:- The floor of every workroom in which processes specified in paragraph 1 are carried on, shall be of a hard material so as to be smooth and impervious and of even surface and shall be cleaned daily, and spillage of any cashewnut oil in any workroom shall be washed with soap and cleaned immediately. 7. Seating accommodation:- Workers engaged in shelling of cashewnuts shall be provided with adequate seats or work benches which shall be cleaned daily. 8. Messrooms:- 1) There shall be provided and maintained for the use of all persons employed in processes specified in paragraph 1, a suitable restroom furnished with sufficient tables and chairs or benches. 282 2) Separate lockers shall be provided where food, etc. shall be stored by workers before it is consumed in the restroom. 9. Food, drinks, etc, prohibited in workrooms:- No food, drink, pan, supari or tobacco shall be brought or consumed by any worker in any room in which processes specified in paragraph 1 are carried out and no person shall remain in any such room during intervals for meals or rest. 10. Washing facilities:- Where roasting, scrubbing and shelling of cashewnuts or extracting oil from cashewnuts or cashewnut shells is carried on, there shall be provided and maintained in a clean state and good repair washing facilities, with a sufficient supply of soap, coconut oil, nail brushes and towels at the scale of one tap or stand pipe for every 10 workers, and the taps or stand pipes shall be spaced not less than 1.2 meters apart. 11. Time allowed for washing:- Before each meal and before the end of the day’s work, at least ten minutes, in addition to the regular meal times, shall be allowed for washing, to each person employed in processes specified in paragraph 1. 12. Smoke or gas produced by roasting cashewnuts. Where smoke or gas is produced in the operation of roasting, provision shall be made for removing the smoke or gas through a chimney of sufficient height and capacity or by such other arrangements as may be necessary to prevent the gas or smoke escaping into the air or any place in which workers are employed. 13. Storage of protective equipment:- A suitable room or a portion of the factory suitably partitioned off, shall be provided exclusively for the storage of all the protective equipment supplied to the workers and no such equipment shall be stored in any place other than the room or places so provided. 14. Medical facilities and records of examinations and tests:- 1) The Occupier of every factory to which this schedule applies, shall:- a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector; and b) provide to the medical practitioner all the necessary facilities for the purpose referred to in clause (a). 2) The said medical practitioner shall inspect daily the hands and feet of all the persons employed in the processes specified in paragraph 1. 3) The record of such examinations carried out by the medical practitioner shall be maintained in a separate register approved by the Chief Inspector, which shall be kept readily available for inspection by the Inspector. 4) The first-aid box maintained shall also contain Burrough’s Solution (1:20) and aqueous solution of tannic acid (10%) for treatment of cases of dermatitis. 15. Medical examination by Certifying Surgeon:- 1) Every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examinations shall include skin test for dermatitis and no worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. 2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every three calendar months. Such examinations shall, wherever the Certifying Surgeon considers appropriate, include asking test for dermatitis. 3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 28. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be 283 kept in the custody of the manager of the factory. The record of each examination carried out under subparagraph (1) and (2), including the nature and the results of these tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. 5) If at any time the Certifying Surgeon, is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance there in would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in subparagraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 16. Exemption:- The Chief Inspector may grant exemptions from the operation of any of these where he is satisfied that their observance is not necessary for safeguarding the health of the workers. Schedule XXX Printing presses and type foundries and certain lead processes carried therein. 1. Definitions:- For the purposes of this schedule:- a) “lead material” means material containing not less than five percent of lead; b) “lead process” means- i) the melting of lead or any lead material for casting and mechanical compressing; ii) the recharging of machines with used lead material; iii) any other work including removal of dress from melting pots and cleaning of plungers; and iv) manipulation, movement or other treatment of lead material. c) “efficient exhaust draught” means localised ventilation effected by heat or mechanical means, for the removal of gas, vapour, dust or fumes so as to prevent them from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove gas, vapour, fume or dust at the point where they originate. 2. Exhaust draught:- 1) None of the following processes shall be Carried on except with an efficient exhaust draught unless carried on in such a manner as to prevent free escape of gas, vapour, fumes or dust into any place in which work is carried on, or unless carried on in electrically heated and thermostatically controlled melting pots:- a) melting lead material or slugs; and b) heating lead material so that vapour containing lead is given off. 284 2) Such exhaust draught shall be effected by mechanical means and so contrived as to operate on the dust, fume, gas or vapour given off as closely as may be at its point of origin. 3) Prohibition relating to women and young persons:- No woman or young person shall be employed or permitted to work in any lead process. 4. Separation of certain processes:- Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another and from any other processes:- a) melting of lead or any lead material; b) casting of lead ingots; and c) mechanical composing. 5. Container for dress:- A suitable receptacle with tightly fitting cover shall be provided and used for dress as it is provided from every melting pot, such receptacle shall be kept covered while in the workroom near the machine except when the dress is being deposit therein. 6. Floor of workroom:- The floor of every workroom where lead process is carried on shall be- a) of cement or similar material so as to be smooth and impervious to water; b) maintained in sound condition; and c) shall be cleansed throughout daily after being thoroughly damped with water at a time when no other work is being carried on at the place. 7. Messroom:- There shall be provided and maintained for the use of all persons employed in a lead process and remaining on the premises during the meal intervals, a suitable messroom which shall be furnished with sufficient tables and benches. 8. Washing facilities:- There shall be provided and maintained in a clean state and in good repair for the use of all persons employed in a lead process:- a) a wash place with either:- i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every five such persons employed at anyone time and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or ii) at least one wash basin for every five such persons employed at any one time fitted with a waste pipe and plug and having an adequate supply of water laid on or always readily available; and b) a sufficient supply of clean towels made of suitable material, renewed daily with a sufficient supply of soap or other suitable cleansing material. 9. Food, drinks, etc. prohibited in workrooms:- No food, drink, pan and supari or tobacco shall be consumed or brought by any workers into any workroom in which any lead process is carried on. 10. Medical facilities and records of examinations and tests:- 1) The occupier of every factory to which the schedule applies, shall:- a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector; and b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause(a). 2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector, which shall be kept readily available for inspection by the Inspector. 285 11. Medical examination by Certifying Surgeon:- 1) Every worker employed in a lead process shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for lead in urine and blood, ALA in urine, haemoglobin, stippling of cells and steadiness test. No worker, shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. 2) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every six calendar months. Such re- examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub-paragraph(1). 3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 28. The record of examination and re-examination carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under subparagraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. 5) If any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said process on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in these documents should include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 12. Exemption:- Where the Chief Inspector is satisfied that all or any of the provisions of this schedule are not necessary for the protection of persons employed, he may by certificate in writing exempt any factory from all or any of such provisions subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector. Schedule XXXI Manufacture of pottery 1. Savings:- These provisions shall not apply to a factory in which any of the following articles, but no other pottery, are made a) unglazed or salt glazed bricks and tiles; and b) architectural terra-cotta made from plastic clay and either unglazed or glazed with a leadless glaze only, 2. Definitions:- For the purposes of this schedule:- a) pottery” includes earthenware, stoneware, porcelain, china tiles, any other articles made from such clay or from a mixture containing clay and other materials such as quartz, flint, feldspar, and gypsum; 286 b) “efficient exhaust draught” means localised ventilation ventilation effected by mechanical or other means for removal of dust or fume so as to prevent it from escaping into air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove effectively dust or fume generated at the point where dust of fume originates; c) “fettling” includes scalloping, towing, sand papering, sand sticking, brushing or any other process of cleaning of potteryware in which dust in given off; d) “leadless glaze” means a glaze which does not contain more than one per cent of its dry weight; of a lead compound calculated as lead monoxide; e) “low solubility glaze” means a glaze which does not yield to dilute hydrochloric acid more than five per cent of its dry weight, of a soluble lead compound calculated as lead monoxide when determined in the manner described below; A weighed quantity of the material which has been dried at 100 degrees centigrade and thoroughly mixed shall be continuously shaken for one hour at the common temperature with 1000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filtrate shall then be precipitated as lead sulphide and weighed as lead sulphate; f) “ground or powdered flint or quartz” does not include natural sands; and g) “potter’s shop” includes all places where pottery is formed by pressing or by any other process and all places where shaping, fettling or other treatment of pottery articles prior to placing for the biscuit fire is carried on. 3. Efficient exhaust draught:- The following processed shall not be carried on without the use of an efficient exhaust draught:- a) all processes involving the manipulation or use of a dry and unfritted lead compound; b) fettling operations of any kind, whether on greenware or biscuit, provided that this shall not apply to the wet fettling, and to the occasional finishing of pottery articles without the aid of mechanical power; c) sifting of clay dust or any other material for making tiles or other articles by pressure, except where- i) this is done in a machine so enclosed as to effectually prevent the escape of dust; or ii) the material to be shifted is an damp that no dust can be given off; d) pressing of tiles from clay dust, an exhaust opening being connected with each press, and pressing from clay dust of articles other than tiles, unless the material is so damp that no dust is given off; e) fitting of tiles made from clay dust by pressure, except where the fetting is done wholly on, or with, damp material, and fetting of other articles made from clay dust, unless the material is so damp that no dust is given off; f) process of loading unloading of sugars where handling and manipulation of ground and powdered flint, quarts, aluminin or other materials are involved; g) brushing of earthern wars biscuit, unless the process is carried on in a room provided with efficient general mechanical ventilation or other ventilation which is certified by the Inspector as adequate having regard to all the circumstances of the case; 287 h) fetting of biscuitware which has been fired in powdered flint or quarts except where this is done in machines so enclosed as to effectually prevent the escape of dust; i) where cleaning after the application of glaze by dipping or other process; j) crushing and dry grinding of materials for pottery bodies and saggars, unless carried on in machines so enclosed as to effectively prevent the escape of dust or is so damp that no dust can be given off; k) sieving or manipulation of powdered flint, quartz, clay grog or mixture of these materials unless it is so damp that no dust can be given off; l) grinding of tiles on a power driven wheel unless an efficient water spray is used on the wheel; m) lifting and conveying of materials by elevators and conveyors unless they are effectively enclosed and so arranged as to prevent escape of dust into the air in or near to any place in which persons are employed; n) preparation or weighing out of flow material, lawning of dry colours, colour dusting and colour blowing; o) mould making unless the bins or similar receptacles used for holding plaster of paris are provided with suitable covers; and p) manipulation of calcined material unless the material has been made and remains so wet that no dust is given off. 4. Separation of processes:- Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another, and from other wet processes:- a) crushing and dry grinding or sieving of materials, fettling, pressing of tiles, drying of clay and greenware, loading and unloading of saggars; and b) all processes involving the use of a dry lead compound. 5. Prohibition on use of glaze:- No glaze which is not a leadless glaze or a low solubility glaze shall be used in a factory in which pottery is manufactured. 6. Prohibition relating to women and young persons:- No woman or young person shall be employed or permitted to work in any of the operations specified in paragraph 4, or at any place where such operations are carried on. 7. Provision of screen to potter’s wheel:- The potter’s wheel (Jolly and Jigger) shall be provided with screens or so constructed as to prevent clay scrapings being thrown of beyond the wheel. 8. Control of dust during cleaning:- 1) All practical measures shall be taken by damping or otherwise to prevent dust arising during cleaning of floors. 2) Damp saw-dust or other suitable material shall be used to render the moist method effective in preventing dust rising into the air during the cleaning process which shall be carried out after work has ceased. 9. Floor of certain workrooms:- The floors of potter’s shops, slip houses, dipping houses and ware cleaning rooms shall be hard, smooth and impervious and shall be thoroughly cleaned daily by an adult male using a moist method. 10. Protective equipment:- 1) The occupier shall provide and maintain suitable overalls and head coverings for all persons employed in process included under paragraph 3. 2) The occupier shall provide and maintain suitable aprons of a waterproof or similar material, which can be sponged daily, for the use of the dippers, dippers assistants, throwers, jolly workers, casters, mould makers and filter press and pug mill workers. 3) Aprons provided in pursuance of paragraph 10(2) shall be thoroughly cleaned daily by the wearers by sponging or other wet process. All overalls 288 and head coverings shall be washed, cleaned and mended at least once a week, and this washing, cleaning or mending shall be provided for by the occupier. 4) No person shall be allowed to work in emptying sacks of dust materials, weighing out and mixing of dusty materials and charging of ball mills and plungers without wearing a suitable and efficient dust respirator. 11. Washing facilities:- 1) The occupier shall provide and maintain, in a clean state and in good repair for the use of all persons employed in any of the processes specified in paragraph 3 - a) a wash place under cover with either - i) a trough with smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimeters for every five such persons employed at any one time, and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 centimeters; or ii) at least one tap or stand pipe for every five such persons employed at any one time, and having a constant supply of clean water, the tap or stand pipe being spaced not less than 120 centimeters apart; and b) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. 12. Time allowed for washing:- Before each meal and before the end of the day’s work, at least ten minutes, in addition to the regular meal times, shall be allowed for washing to each person employed in any of the processes mentioned in paragraph 3. 13. Messroom:- 1) There shall be provided and maintained for use of all persons remaining within the premises during the rest intervals, a suitable messroom providing accommodation of 0.93 square meter per head and furnished with:- a) a sufficient number of tables and chairs or benches with back rest; b) arrangements for washing utensils; c) adequate means for warming food; and d) adequate quantity of drinking water, 2) The room shall be adequately ventilated by the circulation of fresh air and placed under the charge of a responsible person and shall be kept clean. 14. Food, drinks, etc, prohibited in workrooms:- No food, drink, pan and supari or tobacco shall be brought into, or consumed by any worker in any workroom in which any of the processes mentioned in paragraph 3 are carried on and no person shall remain in any such room during intervals for meals or rest, 15. Cloakrooms etc, :- There shall be provided and maintained for the use of all persons employed in any of the processes mentioned in paragraph 3; a) a cloakroom for clothing put off during working hours and such accommodation shall be separate from any mess room; and b) separate and suitable arrangements for the storage of protective equipment provided under paragraph 10, 289 16. Medical facilities and records of examinations and tests:- 1) The occupier of every factory in which manufacture of pottery is carried on, shall a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause(a) 2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector, which shall be kept readily available for inspection by the Inspector. 17. Medical examination by Certifying Surgeon:- 1) Every worker employed in any process mentioned under paragraph 3, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for lead in urine and blood, ALA in urine, haemoglobin content, stippling of cells and pulmonary function tests and chest x-ray for workers engaged in processes mentioned in clauses (a) and (n) of paragraph 3 and pulmonary function tests and chest x-rays for the others. No worker shall be allowed to work after 15 days of his first employment in the factory unless certifies fit for such employment by the Certifying Surgeon. 2) All persons employed in any of the processes included under sub- paragraphs 3(a) and 3(n) shall be examined by a certifying Surgeon once in every 3 calendar months. Those employed in any other processes mentioned in the remaining sub-paragraphs of paragraph 3 shall be examined by a Certifying surgeon once in every twelve calendar months. Such examinations in respect of all the workers shall include all the tests as specified in sub-paragraph (1) except chest x-ray which will be once in 3 years. 3) The Certifying Surgeon after examining a worker, shall issue Certificate of Fitness in Form No. 28. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of such examination carried out under sub-paragraph(1) and (2) including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form No. 29. 4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector, 5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said Certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in subparagraph (5) above shall be re-employed or permitted to work in the said processes 290 unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 18. Exemption:- If in respect of any factory the Chief Inspector is satisfied that all or any of the provisions of this schedule are not necessary for the protection of the persons employed in such factory, he may by a certificate in writing exempt such factory from all or any of such provisions, subject to such conditions as he any specify therein. Such certificate may at any time be revoked by the Chief Inspector without assigning any reasons. Schedule XXXII Operation in Foundry 1. Application:- Provisions of this schedule shall apply to all parts of factories where any of the following operations or processes are carried on; a) the production of iron castings or, as the case may be, steel castings by in moulds made of sand, loam, moulding composition or other mixture of materials, or by shell moulding, or by centrifugal casting and any process incidental to such production; b) the production of non-ferrous castings by casting metal in moulds made of sand, loam, metal, moulding composition of other material or mixture of materials, or by shell mouldings, die-casting (including pressure diecasting), centrifugal casting or continuous casting and any process incidental to such production; and c) the melting and casting of non-ferrous metal for the production of ingots, billets, slabs or other similar products, and the stripping thereof; but shall not apply with respect to:- a) any process in which metal is obtained by a reducing operation or any process incidental to such operation; or b) the production of steel in the form of ingots; or c) any process in the course of the manufacture of solder or any process incidental to such manufacture; or f) the melting and casting of lead or any lead-based alloy for the production of ingots, billets; slabs or other similar products or the stripping thereof, or any process incidental to such melting, casting or stripping. 2. Definition:- For the purpose of this schedule:- a) “approved respirator” means a respirator of a type approved by the Chief Inspector; b) “cupola or furnace” includes a receiver associated therewith; c) “dressing or fettling operations” includes stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not include (a) the removal of metal from a casting when performed incidentally in connection with the machinering or assembling of castings after they have dressed or fettled, or (b) any operation which is knock-out operation within the meaning of this schedule; d) “foundry” means those parts of a factory in which the production of iron or steel or non-ferrous casting (not being the production of pig iron or the production of steel in the form of ingots) is carried on by casting in moulds made of sand, loan, moulding composition or other mixture of materials, or by shell moulding or by centrifugal casting 291 in metal moulds lined with sand, or die casting including pressure die castings, together with any part of the factory in which any of the following processes are carried on as incidental processes in connection with and in the course of, such production, namely, the preparation and mixing of materials used in foundry process, the preparation of moulds and cores, knock out operations and dressing or fettling operations; e) “knock-out operations” means all methods of removing castings from moulds and the following operations, when done in connection therewith, namely, stripping, coring-out and the removal of runners and risers; f) “pouring aisle” means an aisle leading from a main gangway or directly from a cupola or furnace to where metal is poured into mould. 3. Prohibition of use of certain materials as parting materials:- 1) A material shall not be used as a parting material if it is a material containing compounds of silicon calculated as silica to the extent more than 5 per cent by weight of the dry material; Provided that this prohibition shall not prevent the following being used as a parting material if the material does not contain an admixture of any other silica - a) Zirconium silicate (zircon) b) Calcined china clay c) Calcined aluminous fireclay d) Sillimanite e) Calcined or fused alumina f) Olivine g) Natural sand 2) Dust or other matter deposited from a fettling or blasting process shall not be used as a parting material or as a constituent in a parting material. 4. Arrangement and storage:- For the purposes of promoting safety and cleanliness in workrooms the following requirements shall be observed:- a) moulding boxes, loam plates, ladles, patterns, pattern plates, frames, boards, box weights, and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; b) suitable and conveniently accessible racks, bins or other receptacles shall be provided and used for the storage of other gear and tools; c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. 5. Construction of floors:- 1) Floors of indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have an even surface of hard material. 2) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. 3) All parts of the surface of the floor of any such indoor workplace which are of sand shall, so far as practicable, be maintained in an even and firm condition. 6. Cleanliness of indoor workplaces: 1) All accessible parts of the walls of every indoor workplace in which the processes are carried on and of everything affixed to those wall shall be 292 effectively cleaned by a suitable method to a height of not less than 4.2 metres from the floor at least once in every period of fourteen months. A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date (which shall be not less than five months nor more than nine months after the last immediately preceding washing, cleaning or other treatment). 2) Effective cleaning by a suitable method shall be carried out at least once every working day of all accessible parts of the floor of every indoor workplace in which the processes are carried on, other than parts which are of sand; and the parts which are of sand shall be kept in good order. 7. Manual operations involving molten metal:- 1) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation:- a) which is adequate for the safe performance of the work and b) which, so far as reasonably practicable, is kept free from obstruction. 2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which where any person walks while engaged in the operation shall be on the same level; Provided that, where necessary to enable the operation to be performed without undue risk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 8. Gangways and pouring aisles:- 1) In every workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this schedule and, so far as reasonably practicable, in every other workroom to which this paragraph applies, sufficient and clearly defined main gangways shall be provided and properly maintained which:- a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; b) shall be kept, so far as reasonably practicable, free from obstruction; c) if not used for carrying molten metal, shall be at least 920 millimetres in width; d) if used for carrying molten metal shall be- i) where truck ladles are used exclusively, at least 600 millimeters wider than the overall width of the ladle; ii) where hand shanks are carried by not more than two men, at least 920 millimeters in width; iii) where hand shanks are carried by more than two men, at least 1.2 metres in width; and iv) where used for simultaneous travel in both directions by men carrying hand shanks, at least 1.8 metres in width. 2) In workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule, sufficient and clearly defined pouring aisles shall be provided and properly maintained which- a) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; 293 b) shall be kept so far as reasonable practicable free from obstruction; c) if molten metal is carried in hand ladles or bull ladles by not more than two men per ladle, shall be at least 460 millimeters wide, but where any moulds alongside the aisle are more than 510 millimeters above the floor of the aisle, the aisle shall be not less than 600 millimeters wide; d) if molten metal is carried in hand ladles or bull ladles by more than two men per ladle, shall be at least 760 millimeters wide; e) if molten metal is carried in crane, trolley or truck ladles, shall be of a width adequate for the safe performance of the work. 3) Requirements of sub-paragraph (1) and (2) shall not apply to any workroom or part of a workroom if, by reason of the nature of the work done therein, the floor of that workroom or, as the case may be, that part of a workroom has to be of sand. 4) In this paragraph “workroom to which this paragraph applies” means a part of a ferrous or non-ferrous foundry in which molten metal is transported or used, and a workroom to which this paragraph applies shall be deemed for the purposes of this paragraph to have been constructed, reconstructed or converted for use as such after the making of this schedule if the construction, reconstruction or conversion thereof was begun after the making of this schedule. 9. Work near cupolas and furnaces:- No person shall carry out any work within a distance of 4 metres from a vertical line passing through the delivery end of any spout of cupola or furnace, being a spout used for delivering molten metal, or within a distance of 2.4 metres from a vertical line passing through the nearest part of any ladle which is in position at the end of such a spout, except, in either case, where it is necessary for the proper use of maintenance of a cupola or furnace that work should be carried out with in that distance of that work is being carried out at such time and under such conditions that there is no danger to the person carrying it out from molten metal which is being obtained from the cupola or furnace or is in a ladle in position at the end of the spout. 10. Dust and fumes:- 1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. 2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. 3) Mould stoves, core stoves and annealing furnaces shall be so designed constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. 4) All knock-out operations shall be carried out- a) in a separate part of the foundry suitably partitioned off, being a room or part in which, so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard or general ventilation are provided; or b) in an area of the foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. 294 5) All dressing or fettling operations shall be carried out:- a) in a separate room or in a separate part of the foundry suitably partitioned off; or b) in an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 11. Maintenance and examination of exhaust plant:- 1) All ventilation plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be properly maintained. 2) All ventilating plant used for the purpose of extracting, suppressing or controlling dust or fumes shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person at least once in every period of twelve months; and particulars of the results of every such examination and test shall be entered in an approved register which shall be available for inspection by an Inspector. Any defect found on any such examination and test shall be immediately reported in writing by the person carrying out the examination and test to the occupier or manager of the factory. 12. Protective equipment- 1) The occupier shall provide and maintain suitable protective equipment specified for the protection of workers; a) Suitable gloves or other protection for the hands for workers engaged in handling any hot material likely to cause damage to the hands by burn, scald or scar, or in handling pig iron, rough castings or other articles likely to cause damage to the hands by cut or abrasion; b) approved respirators for workers carrying out any operations creating a heavy dust concentration which cannot be dispelled quickly and effectively by the existing ventilation arrangements. 2) No respirator provided for the purposes of clause 1(b) has been worn by a person shall be worn by another person if it has not since been thoroughly cleaned and disinfected. 3) persons who for any of their time- a) work at a spout of or attend to, a cupola or furnace in such circumstances that material there from may come into contact with the body, being material at such a temperature that its contact with the body would cause a burn; or b) are engaged in, or in assisting with, the pouring of molten metal; or c) carry by hand or move by manual power any ladle or mould containing molten metal; or d) are engaged in knocking out at operations involving material at such a temperature that its contact with body would cause a burn; Shall be provided with suitable footwear and gaiters which worn by them prevent, so far as reasonably practicable, risk of burns to his feet and ankles. 4) Where appropriate, suitably screens shall be provided for protection against flying materials (including splashes of molten metal and sparks and chips thrown off in the course of any process). 5) The occupier shall provide and maintain suitable accommodation for the storage and make adequate arrangements for cleaning and maintaining of the protective equipment supplied in pursuance of this paragraph. 295 6) Every person shall make full and proper use of the equipment provided for his protection in pursuance of sub-paragraph (1) and (4) and shall without delay report to the occupier, manager or other appropriate person any defect in, or less of, the same. 13. Washing and bathing facilities:- 1) There shall be provided and maintained in clean state and good repair for the use of all workers employed in the foundry- a) a wash place under cover with either- i) a trough with impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every 10 such persons employed at any one time and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 centimetres or ii) at least one tap or stand pipe for every 10 such persons employed at any one time, and having a constant supply of clean water, the tap or stand pipe being spaced not less than 1.2 metres apart and b) not less than one half of the total number of washing places provided under clause (a) shall be in the form of bath room. c) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. 2) The facilities provided for the purposes of sub-paragraph (1) shall be placed in charge of a responsible person or persons and maintained in a clean and orderly condition. 14. Disposal of dross and skimmings:- Dross and skimmings removed from molten metal or taken from furnace shall be placed forthwith in suitable receptacles. 15. Disposal of waste:- Appropriate measures shall be taken for the disposal of all waste products from shell moulding (including waste burnt sand) as soon as reasonably practicable after the castings have been knocked-out. 16. Material and equipment left out of doors:- All material and equipment left out of doors (including material and equipment so left only temporarily or occasionally) shall be so arranged and placed as to avoid unnecessary risk. There shall be safe means of access to all such material and equipment and, so far as reasonably practicable, such access shall be by road ways or pathways which shall be properly maintained. Such roadways or pathways shall have a fire and even surface and shall, so far as reasonably practicable be kept free from obstruction. 17. Medical facilities and records of examinations and tests:- 1) The occupier of every factory to which the Schedule applies, shall - a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector; and b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a) 2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector, which shall be kept readily available for inspection by the Inspector. 18. Medical examination by Certifying Surgeon:- 1) Every worker employed in foundry shall be examined by a Certifying Surgeon within 15 days of his first employment. Such medical examination shall include pulmonary function tests and chest X-ray. No 296 worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. 2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every twelve months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub-paragraph (1) except chest X-ray which will be once in 3 years. 3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 28. The record of examination and re-examination carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under subparagraphs (1) and (2), including the nature and the results off the tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 4) The certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. 5) If at any time the Certifying Surgeon is of the opinion that a worker is no linger fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said process. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying surgeon, after further examination, again certifies him fit for employment in those processes. 19. Exemption:- If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Rule 161. Notification of accidents or dangerous occurrences: 2) When any accident specified in sub-clause (a) of clause 1 of the Schedule hereto appended or any dangerous occurrence specified in clause 2 of the said schedule takes place in a factory, the manager of the factory shall, within 4 hours of the happening of such accident or occurrence, send notice thereof by telephone, special messenger or telegram to the Inspector and where the accident is fatal or of such a serious nature that it is likely to prove fatal, notice as aforesaid shall also be sent to: a) the District Magistrate or Sub-Divisional Officer, b) the Officer-in-Charge of the nearest police station, and c) the nearest relatives of the injured or deceased person. 297 2) The notice so given shall be confirmed by the manager of the factory to the authorities mentioned in sub-rule (1) by sending to them a written report in the case of an accident in Form 30 and in the case of dangerous occurrence, in Form 31 within 12 hours of the taking place of any such accident or occurrence referred to in that sub-rule. 3) If in the case of an accident, the injured person subsequently dies due to such accident, information of his death whenever known shall be sent by the manager by telephone, special messenger or telegram within 24 hours of the occurrence to: a) the Inspector b) the District Magistrate or Sub Divisional Officer c) the Officer-in Charge of the nearest police station. Explanation: For the purpose of this rule “accident of a serious nature” means an accident which results in: i) immediate loss of any part of the body or any limb or part thereof ii) crushed or serious injury to any part of the body due to which loss of the same is obvious or any injury which is likely to prove fatal. iii) unconsciousness, or iv) severe burns or scalds due to chemicals, steam or any other cause. 4) Wherever the person injured does not return to work in the factory before the expiry of 21 days after the occurrence of the accident with or without disablement and wherever the person injured returns to work in the factory after sustaining compassable disablement as a result of the accident, the Manager of the factory shall send to the Inspector within 28 days of the occurrence of the accident, a written report in the prescribed Form 32 and follow it up a necessary with further reports in the same Form 32 once every fortnight thereafter, until the final report on the date of return to work of the person injured is made. In the event of the person injured not returning to work of his own accord or otherwise the full circumstances of the same should also be reported to the Inspector by the Manager of the factory within seven days of his name being removed from muster roll of the factory. Schedule 1 a) Accidents which cause death to any person or are of a serious nature. b) Accidents which cause such bodily injury as will prevent or will probably prevent the person injured from working for a period of 48 hours or more immediately following the accident. 2. The following classes of dangerous occurrences, whether or not they are attended by personal injury or disablement: a) Bursting of a vessel used for containing steam under pressure greater than atmospheric pressure, other than plant which comes within the scope of the Indian Boilers Act. b) Collapse of failure of a crane, derrick, winch, lift, hoist or other appliances used in raising or lowering persons or goods or any part thereof or the overturning of a crane. c) Explosion, fire, bursting out, leakage or escape of any molten metal, hot liquor or gas causing bodily injury to the person or damage to any part or portion of the factory in which persons are employed or damage to any plant machinery or material. d) Explosion of a receiver or container used in any process or for storage at a pressure greater than atmospheric pressure, of any gas or any gases (including air) or any liquid or any solid. 298 e) Collapse or subsidence of any floor, gallery, roof, bridge, tunnel, chimney, wall or building forming part of a factory or within the compound or cartilages of factory. Rule 162. Notice of Poisoning or Disease: A notice in Form 33 should be sent forthwith both to the Chief Inspector and to the Certifying Surgeon, by the manager of a factory in which there occurs a case of lead, phosphorous, mercury, manganese, arsenic, carbon bisulphide or benzene poisoning; or of poisoning by nitrous fumes or by halogen derivatives of the hydrocarbons of aliphatic series; or of chrome ulceration, anthrax, silicosis, toxic anaemia, toxic jaundice, primary epitheliomatous cancer of skin, or of pathological manifestations due to radium or other radio-active substances or x-rays. Rule 163. Procedures in appeals: 1) An appeal presented under section 107 shall lie to the Chief Inspector or in cases where the order appealed against is an order passed by that officer to the State Govt. or to such authority as the State Government may appoint in this behalf and shall in the form of memorandum setting forth concisely the grounds of objection to the order and bearing court fees stamps in accordance with the Article 11 of Schedule II of the court Fees Act, 1870 and shall be accompanied by a copy of the order appealed against. 2) Appointment of Assessors: On receipt of the memorandum of appeal, the appellate authority shall, if it thinks fit or if the appellant has requested that the appeal should be heard with the aid of assessors, call upon the body declared under sub-rule (3) to be representative of the industry concerned, to appoint an assessor within a period of 14 days. If the assessor is nominated by such body, the appellate authority shall appoint a second assessor itself. It shall then fix a date for the hearing of the appeal and shall give due notice of such date to the appellant and to the inspector whose order is appealed against, and shall call upon the two assessors to appear upon such date to assist in the hearing of the appeal. 3) The appellant shall state in the memorandum presented under sub-rule(1) whether he is a member of one or more of the following bodies. The body empowered to appoint the assessor shall:- a) if the appellant is a member of one such bodies, be that body; b) if he is a member of two such bodies, be the body which the appellant desires should appoint such assessor; and c) if the appellant is not a member of any of the aforesaid bodies or if he does not state in the memorandum which of such bodies he desires should appoint the assessor, be the body which the appellate authority considers as the best fitted to represent the industry concerned. 4) Remuneration of assessors:- An assessor appointed in accordance with provisions of sub-rules (2) and (3) shall receive for the hearing of the appeal, a fee to be fixed by the appellate authority, subject a maximum of fifty rupees per diem. He shall also receive the actual travelling expenses. The fees and travelling expenses. The fees and travelling expenses shall be paid to the assessor by Government; but where assessors have been appointed at the request of the appellant and the appeal has been decided wholly or partly against him, the appellate authority may direct that the fees and travelling expenses of the assessor shall be paid in whole or in part by the appellant. Rule 164. Display of notices: 299 The abstract of the Act and of the Rules required to be displayed in every factory shall be in Form 34 Rule 165. Returns: The manager of every factory shall furnish to the Inspector or other officer appointed by the State Government in this behalf, the following returns in the form and within the due dates specified below:- a) annual return in Form 35 in duplicate, on or before the 31st January of each year; and b) Deleted. Rule 166. Service of notices: The dispatch by post under registered cover of any notice or order shall be deemed sufficient service on the occupier, owner or manager of a factory of such notice or order. Rule 167. Information required by the Inspector: The occupier, owner, or manager of a factory shall furnish any information that an Inspector may require for the purpose of satisfying himself whether any provision of the Act and Rule have been complied with or whether any order of an Inspector has been duly carried out. Any demand by an Inspector for any such information, if made, during the courses of any inspection, shall be complied forthwith if the information is available in the factory, or if made in writing, shall be complied with, within seven days of receipt thereof. Rule 168. Registers / records to be produced on demand to the Inspector. The registers, records and notices maintained and exhibited under the provisions of these rules shall always be available at or as near as practicable to the site of employment and shall be produced or caused to be produced for inspection at all reasonable hours by any Inspector having jurisdiction over the factory. Rule 169. Permissible levels of certain chemical substances in work environment: Without prejudice to the requirements in any other provisions in the Act or the Rules, the requirements specified in this Schedule shall apply to all factories. Schedule 1. Definition: For the purpose of this schedule- a) “mg/m3” means milligrams of a substance per cubic meter of air. b) “mppcm” means million particles of a substance per cubic meter of air. c) “pmm” means parts of vapour or gas per million parts of air by volume at 250 C and 7600 mm of mercury pressure. d) “Time Weighted Average Concentration” means the average concentration of a substance in the air at any work location in a factory computed from evaluation of adequate number of air samples taken at that location spread over the entire shift on any day, after giving weightage to the duration for ____________________________________________________________________ 1Tenth Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/2199 dtd., 27.01.2021. 300 which each such sample is collected and the concentration prevailing at the time of talking the sample. Time Weighted Average Concentration: = C1T1 +C2 T2 +... +Cn Tn T1 +T2 +......Tn Where C1 represents the concentration of the substance for duration T1 hours; C2 represents the concentration of the substance for duration T2 hours; and Cn represents the concentration of the substance for duration Tn hours e) “Work Location” means a location in a factory at which a worker works or may be required to work at any time during any shift on any day. 2. Limits of Concentrations of Substance at Work Locations: 1) The time weighted average concentration of any substance listed in Table 1 or 2 of the schedule, at any work location in a factory during any shift on any day shall not exceed the limit of permissible time weighted average concentration specified in respect of that substance: Provided that in the case of a substance mentioned in Table 1 in respect of which a limit in terms of short term maximum concentration is indicated, the concentration of such a substance may exceed the permissible limit of the time weighted average concentration for the substance for short periods not exceeding 15 minutes at a time, subject to the condition that- a) such periods during which the concentration exceeds the prescribed time weighted average concentration are restricted to not more than 4 per shift. b) the time interval between any two such periods of higher exposure shall not be less than 60 minutes; and c) at no time the concentration of the substance in the air shall exceed the limit of short term maximum concentration. 2) In the case of any substance given in Table 3, the concentration of the substance at any work location in a factory at any time during any day shall not exceed the limit of exposure for that substance specified in the table. 3) In the cases where the word “skin” has been indicated against certain substance mentioned in Tables 1 and 3, appropriate measures shall be taken to prevent absorption through cutaneous routes particularly skin, mucous membranes, and eyes as the limits specified in these Tables are for conditions where the exposure is only thorough respiratory tract. 4) a) In case, the air at any work location contains a mixture of such substance mentioned in Table 1, 2, or 3, which have similar toxic properties, the time weighted concentration of each of these substances during the shift should be such, that when these time weighted concentration divided by the respective permissible time weighted average concentration specified in the above mentioned tables, and the fractions obtained are added together, the total shall not exceed unity. i.e. C1 + C2 +..... Cn Should not exceed unity L1 L2 Ln When C1, C2 ………… Cn are the time weighted concentration of toxic substances 1,2 ………… and n respectively, determined after measurement of work location; 301 and L1, L2 ………… Ln are the permissible time weighted average concentration of the toxic substances 1, 2, ………… and in respectively. b) In case the air at any work location contains a mixture of substances, mentioned in Table 1, 2, or 3, and those do not have similar toxic properties, then the time weighted concentration of each of these substances shall not exceed the permissible time weighted average concentration specified in the above mentioned tables, for that particular substance. c) The requirement in clauses (a) and (b) shall be in addition to the requirements in paragraphs 2(1) and 2(2). 3. Sampling and evaluation procedures:- 1) Notwithstanding provisions in any other paragraphs, the sampling and evaluation procedures to the adopted for checking compliance with the provisions in the schedule shall be as per standard procedures in vogue from time to time. 2) Notwithstanding the provisions in paragraph 5, the following conditions regarding the sampling and evaluation procedures relevant to checking compliance with the provisions in this schedule are specified. a) For determination of the number of particles per cubic metre in item 1(a) i (1) in Table 2, samples are to be collected by standard or midget impinger and the counts made by light-field technique. b) The percentage of quartz in the 3 formulate given in item 1 (a) i) of Table 2 is to be determined from air borne samples. c) For determination of number of fibres as specified in item 2(a) of Table 2, the membrane filter method at 430 % magnification 14mm objectives with phase contrast illumination should be used. d) Both for determination of concentration and percentage of quartz for use of the formula given in item 1(a) (i) (2) of Table 2, the fraction passing through a size-selector with the following characteristics should only be considered. Aerodynamic diameter Percentage allowed (unit density sphere) by size-selecter 2.0 90 2.5 75 3.5 50 5.0 25 10.0 0 4. Power to require assessment of concentration of substances.- 1) An Inspector may, by an order in writing, direct the occupier or manager of a factory to get before any specified date, the assessment of the time weighted average concentration at any work location of any of the substances mentioned in Table 1, 2 or 3 carried out. 2) The results of such assessment as well as the method followed for air sampling and analysis for such assessment shall be sent to the Inspector with 3 days from the date of completion of such assessment and also a record of the same kept readily available for inspection by an Inspector. 5. Exemption:- If in respect of any factory or a part of a factory, the Chief Inspector is satisfied that, by virtue of the pattern or working time of the workers at different work locations or an account of other circumstances, no worker is exposed, in the air at the work locations, to a substance or substances specified in Tables 1, 2, or 3 to such an extent as is likely to be injurious to his health , he (the Chief Inspector) may by an order in writing, exempt the factory or a part of the factory from the 302 requirements in paragraph 2, subject to such conditions, if any as he may specify therein. Substance Permissible limits of exposure Time-weighted average Short-term maximum Concentration concentration ppm Mg/m3 ppm Mg/m3 Acetic acid 10 25 15 37 Acrolein 0.1 0.25 0.3 0.8 Aldrin-skin - 0.25 - 0.75 Ammonia 25 18 35 27 Aniline-skin 2 10 5 20 Anisidine (O-poisomers)- 0.1 0.5 - - skin Arsenic & Compounds (as - 0.2 - - As) Benzene 10 30 - - Bromine 0.1 0.7 0.3 2 2 Butanene Methylothyl 200 590 300 885 (ketone-MEK) n-Butyl acetate 150 710 200 950 Sec/tert. Butyl acetate 200 950 250 1190 Cadmium-dust and salts(as - 0.05 - 0.2 Cd) Calcium oxide - 2 - - Carbaryl (Sovin) - 5 - 10 Carbofuran (Furadan) - 0.1 - - Carbon disulfide-skin 2 60 30 90 Carbon monoxide 50 55 400 440 Carbon tetrachloride-skin 10 65 20 130 Carbonyl chloride 0.1 0.4 - - (phosgene) Chlordane-skin - 0.5 - 2 Chlorobenzene (mono 75 350 - - chlorobenzene) Chlorine 1 3 3 9 bis-Chloromethyl either 0.001 - - - Chromic acid and - 0.05 - - chromates(as, Cr) Chromium, Sel-chramic - 0.5 - - Chromous salts (as Cr) Copper fume - 0.2 - - Cotton dust, raw - 0.2 - 0.6 Cresol, all isomers-skin 5 22 - - Cyanides, as CN) skin - 5 - - Cyanegen 10 20 - - DDT (Dichlorodiphenyl- - 1 - - trichlore-ethane) Demeton-skin 0.01 0.1 0.03 0.3 303 Diazion-skin - 0.1 - 0.3 Dibutyl phthalate - 5 - 10 Dichlorves(DDVP) -skin 0.1 1 0.3 3 Dieldrin-skin - 0.25 - 0.75 Dinitrobenzene(all 0.15 1 0.5 3 isomers)-skin Dinitrotoluene-skin - 1.5 - 5 Diphenyl 0.2 1.5 0.6 4 Endosulfan (Thiodan)-skin - 0.1 - 0.3 Endrin-skin - 0.1 - 0.3 Ethyl acetate 400 1000 - - Ethyl alcohol 1000 1900 - - Ethyl amine 10 18 - - Flourides (as F) - 2.5 - - Flourine 1 2 2 4 Hydrogen Cyanide-skin 10 11 15 16 Hydrogen sulfide 10 15 15 27 Iron oxide fume (Fe203 as - 5 - 10 Fe) Iscamyl acetate 100 525 125 655 Isoamyl alcohol 100 525 125 655 Isobutyloalcohol 50 150 75 225 Lead, inorg, fumes and - 0.15 - - dusts (as Pb) Lindane-skin - 0.5 - 1.5 Mala thien-skin - 10 - - Manganese fume (as Mo) - 1 - 3 Mercury (as Hg) - 0.00 - 0.15 Mercury (alkyl 0.001 0.01 0.003 0.03 compounds)-skin (as Hg) Methyl alcohol (methanol)- 200 260 250 310 skin Methyl cellosolve-skin (2- 25 80 35 120 methoxy ethanol) Methyl isobutyl ketone-skin 100 410 125 510 Napthalene 10 50 15 175 Nickel carbonyl (as Ni) 0.05 0.35 - - Nitric acid 2 5 4 10 Nitric oxide 25 30 35 45 Nitrobenzene-skin 1 5 2 10 Oil mist-mineral - 5 - 10 Parathion-skin - 0.1 - 0.3 Phenel-skin 5 19 10 30 Phorate (Thimet)-skin - 0.05 - 0.2 Phosgene (Carbonyl 0.1 0.4 - - chloride) Phosphine 0.3 0.4 1 1 Phosphorous (yellow) - 0.1 - 0.3 Phosphorous pentachloride - 1 - 3 Phosphorous trichloride 0.5 3 - - Picric acid-skin - 0.1 - 0.3 304 Pyridine 5 15 10 30 Silane (Silicon tetrahydride) 0.5 0.7 1 1.5 Styrene, Menemer 100 420 125 525 (phenylethylene) Sulfur dioxide 5 13 - - Sulfuric acid - 1 - - Toluene (teluel)-skin 100 375 150 560 o-Toludine 5 22 10 44 Trichloroethylene 100 535 150 800 Vinyl chloride 5 10 - - Welding fumes (Noc) - 5 - - Xylene (o-m--p-isomers)- 100 435 150 655 skin TABLE 2 Substance Permissible time weighted average Concentration ________________________________________________________________________ 1. Silica (a) Crystallin e i) Quartz 1060 1) In terms of dust count : ----------------------------------- mpp cm % Quartz + 10 10 2) In terms of respirable : ----------------------------------- mg/m3 dust % respirable quartz +2 30 3) In terms of total dust : ------------------------------------ mg/m3 % quartz + 3 ii) Cristobalite Half the limits given against quartz iii) Tridymite Half the limits given against quartz iv) Silica fused Same limit as for quartz v) Tripoli Same limit as in formula in item 2 given against quartz b) Amorphous 705 mpp cm 2. Silicate having less than 1% free silica by weight a) Asbestos (fibres longer than 5 microne) 2 fibres/cubic centimeter b) Mica 705 mppcm c) Mineral wool fibre 10mg/m3 d) Porlite 1060 mppcm e) Portland cement 1060 mppcm f) Soap stone 705 mppcm g) Talc (monobostiform) 705 mppcm h) Talc (fibrous) same limit as for asbestos i) Tromolite same limit as for asbestos 3. Coal dust 305 1) For airborne dust having less than 5% silicon dioxide by weight 2) For airborne dust having over 5% silicon dioxide : 2 mg/m3 : Same limit as prescribed by formula in item (2) against quartz. TABLE 3 Substance Permissible limit of exposure ppm mg/m3 Acetic anhydride 5 20 O-Dichlorobenzene 50 300 Formaldehyde 2 3 Hydrogen Chloride 5 7 Manganese & Compounds (As Mn) - 5 Nitrogen dioxide 5 9 Nitroglycerin-skin 0.2 2 Potassium hydroxide - 2 Sodium hydroxide - 2 2,4,6 - Trinitrotoluene (TNT) - 0.5 Rule 170 Deleted. Rule 171. Register of Accidents and Dangerous Occurrences: The manager of every factory shall maintain a register of all accidents and dangerous occurrences which occur in the factory in Form 38. Rule-172. Maintenance of Inspection Book: The manager of every factory shall maintain a bound inspection book and shall produce it when so required by the Inspection or Certifying Surgeon. Rule-173. Information regarding closure of factories: (1) The occupier and the manager shall be jointly or severally responsible for sending information in duplicate to the Inspector, of any intended closure to the factory or any shift, section or department thereof, immediately after it is decided to do so, and before the closure takes place, stating- a) the reasons for closure; b) the reasons for closure; c) the number of workers on the muster-roll of the factory ofn the day the information is sent; d) the number of workers likely to be affected by the closure; ________________________________________________________________________ 1Tenth Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/2199 dtd., 27.01.2021. 306 e) the probable period of closure; Provided further that it shall not be necessary for the occupier or manager to send information of intended closure if the closure is rendered inevitable on account of fire, breakdown of machinery, stoppage of power or water supply or any other cause beyond his control. 2) The Occupier and the Manager shall be jointly or severally responsible for sending also information in duplicate to the Inspector as soon as the factory or any shift, section or department thereof, is actually closed in the Form 39. 3) The Occupier and the Manager shall be jointly or severally responsible for sending also information in duplicate to the Inspector as soon as the factory or any shift, section or department thereof, is reopened in Form 40. Explanation 1: For the purpose of this rule, “closure” means the closing the factory, or any shift, section or department thereof or the total or partial suspension of work (other than work of a temporary nature) by the occupier or manager of the factory, or total or partial refusal by the occupier or manager of the factory to continue to employ persons employed by him where such refusal does not amount to the discharge, dismissal or suspension of worker or workers by way of punishment. Explanation 2: This rule shall not apply in the case of any section or department of a factory if such closure does not affect the total number of workers employed in the factory. Rule 174. Power to Cancel the Licence and Registration upon receipt of report: The Chief Inspector may, on receipt of a report in respect of any factory under sub-rule (1) of 173, and after making such enquiry as he thinks fit, by order, cancel the licence and registration in respect of such factory with effect from such date as may be specified in this order. Rule 175. Preservation of Records The records specified in column 1 of the table below shall be preserved in the office of the Chief Inspector for the periods specified in the corresponding entries in column 2 thereof:- Records Period of Retention Applications presented under Rule7 to 9 of Five Yrs from the date of disposals of the the Tripura Factories Rules 2007 applications Counterfoils and licences issued under the Five Yrs form the date of issue of licences. said Rules. Challans Five yrs from the date of issue of Licences. Rule 176. Manner of Destruction for Records After the period of retention specified in rule 180, the record shall be destroyed either by tearing or burning in the presence of the head of the office. Rule 177. Language in the Registers and records The registers and records required to be maintained in the factory under the provisions of the Act and these rules shall be either in English or in a Bengali. 307 Rule 178. Exhibition of Name Board The name board of a factory shall be displayed conspicuously at the entrance of the factory premises. The name board shall be in English or Bengali. Rule 179. Power of Exemption The State Government may, be notification in the official Gazette, exempt subject to other to such conditions as it may be consider necessary, any workshop or workspace where a manufacturing process carried on and which is attached to a public institution maintaining for the process of education, training or reformation, from all or any provisions of those rules. Rule-179A(1) Additional wages for works during holidays Where a worker is required to work in a factory on a paid holiday, he shall, if the total period of working hours in the respective week does not exceed forty eight hours be entitled to additional wages for that holiday at the following rates :- (i) Two – times the normal daily wages for eight hours of work. (ii) For works less than eight hours the wages shall be one eighth of two times of normal daily wages for every hours or part of an hour of work. (2) Notwithstanding anything contained in these rules the State Government may by order to be published in the official gazette direct that the provisions of sub-rule (I) shall apply to any factory in respect of any past period. Explanation – For the purpose of this rule “paid holiday” (i) In relation to a factory of the Government means a day declared by the Government as closed. (ii) In relation to a factory under the private sector or the Government undertaking means a day declared as closed by the management of such factory but does not include weekly holiday.1 Rule 180. Repeal and saving On the commencement of these rules, the Tripura Factories Rules, 1952, shall stand repealed. Notwithstanding such repeal, anything done or any action taken under the said Rule shall be deemed to have been done or taken under the corresponding provisions of this Rules. 1 First Amendment vide No.F.7(121)-FB/AM/2007/225 dtd., 22.04.2008 308 FORM 1 (APPLICATION FOR GRANT OF CERTIFICATE OF COMPETENCE TO A PERSON) 1. Name 2. Father’s Name 3. Date of Birth 4. Address i) Permanent ii) Present 5. Name & Address of the Organization :- 6. Designation :- 7. Education Qualification ( Copies of testimonials to be attested) 8. Details of professional experience ( in chronological order) Name of the Organization Period of service Designation Area of Responsibility 1 2 3 4 9. Membership, if any, of the professional bodies. 10. (i) Details of facilities (examination, testing etc.) at his disposal. (ii) Arrangements for calibrating and maintaining the accuracy of those facilities. 11. Purpose for which competency certificate is sought (Section or Sections of the Act should be stated). 12. Whether the applicant has been declared as a competent person under any statute ( If so the details). 13. Any other relevant information Declaration by the applicant. I, ………………………………………….. hereby declare that the information furnished above is true. I undertake a) that in the event of any change in the facilities at my disposal ( either addition or deletion ) or my leaving the aforesaid organization, I will promptly inform the chief Inspector of Factories b) to maintain the facilities in good working order, calibrated periodically as per manufacturers instructions or as per National Standards; and c) to fulfill and abide by all the conditions stipulated in the certification of competency and instructions issued by the Chief Inspector of Factories from time to time Place ………… Date …………. Signature of the applicant Declaration by the Institution ( if employ*********) I, ……………………………….. . certify that Shri ……………………….is in our employment and we nominate him on behalf of the organization for the purpose of being declared as a competent person under the Act. I also under take that I will -- a) notify the Chief Inspector in case the competent person leaves our employment; b) provide and maintain in good order all facilities at his disposal as mentioned above. c) notify the Chief Inspector of Factories any change in the facilities ( either addition or deletion ). Dated : ………… Signature Designation Telephone No . Official Seal Form 2 [See rule 3(3)] (APPLICATION FOR GRANT OF CERTIFICATE OF COMPETENCE TO AN ORGANISATION) 1). Name and full Address of the organization 2). Organization’s Status (specify whether Government, autonomous, Co-Operative 3). Purpose for which Competency Certificate is sought (specify Section(s) of the Act) 4). Whether the organization has been declared as a competent person under this or any other statute. If so give details. 5). Particulars of persons employed and possessing qualification and experience as set out in schedule annexed Sl. No. Name and Designation Qualifications. Experience Section(s) and the rules under which competency is sought for 1 2 3 4 5 6). Details of facilities (relevant to item 3 above) and arrangements made for their maintenance and periodic calibration. 7). Any other relevant information. 8). Declaration : I, ……………………………. hereby on behalf of ........................................... certify that the details furnished above are correct to the best of my knowledge. I undertake to – (i) maintain the facilities in good working order, calibrated periodically as per manufacturers instructions or as per National Standard; and (j) to fulfil and abide by all the conditions stipulated in the certificate of competency and instructions issued by the Chief Inspector of Factories from time to time. Signature of head of the Institution or of the persons authorized to sign on his behalf. Designation Place & Date : Form 3 See rule 3(3) CERTIFICATE OF COMPETENCY ISSUED TO PERSON OR AN INSTITUTION IN PURSUANCE TO SECTION 2(CA) OF THE FACTORIES ACT AND RULES MADE THERE UNDER I, ………………………………………………………, in exercise of the powers conferred on me under Section 2(ca) of the Factories Act, 1948 and rules made there under, hereby recognize ………………………………………………………………..(Name of the Institution) or Shri …………………………...(Name of the Person) employed in ……..……………………... (Name of the Organization) to be a competent person for the purpose of carrying out tests, examinations, inspections and certification for such buildings, dangerous machinery, lifts and hoists, lifting machines and lifting tackles, pressure plants, confined space, ventilation system and process or plant and equipment as the case may be, used in the factory located in …………………………………………………. under section …………………………………………..and the rules made there under. …………………………………………………………………………………………… … Strike out the words not applicable. This certificate is valid from …………………………. to ………………………. This certificate is issued subject to the conditions stipulated hereunder: i) Test Examination and inspections shall be carried out in accordance with the provisions of the Act and the rules made there under; j) Test examination and inspections shall be carried out under direct supervision of the competent person or by a person so authorized by an Institute recognized to be a competent person. k) The certificate of competency issued in favour of a person shall stand cancelled if the person leaves the organization mentioned in his application; l) The Institution recognized as a competent person shall keep the Chief Inspector of Factories informed of the names, designations and qualifications of the person authorized by it to carry out test, examination and inspection. Station Official Seal Signature of the Chief Inspector of Factories Note :- A separated certification should be issued under each relevant Section . A person or an institution may be recognized competent for the purpose of more than one section of the Act. Form 4 ( See rules 6) CERTIFICATE OF STABILITY 1. Name of the factory 2. Full Postal address of the factory 3. Name of the Occupier 4. Nature of the manufacturing process to be carried on the factory 5. Number of the floors on which workers will employed I certify that I have inspected the premises, the plants of which have been approved by the Chief Inspector of Factories in his letter no .......................................................................................................................... date d ………….and examined the various parts including the foundations with special reference to the machinery, plant, etc that have been installed. I am of the opinion that all the works of Engineering construction in the premises is/are structurally sound and that its/their stability will not be endangered by its/their use as a factory/part of a factory for the manufacture of ……….. or for which the machinery, plant etc., installed are intended. Signature Qualificatio n Address Date (If employed by a company or Association, name and address of the company or Association). Form 5 (See rules 5(2)) APPLICATION FOR PERMISSION TO CONSTRUCT, EXTEND OR TAKE INTO USE ANY BUILDING AS A FACTORY 1) Applicant’s name 2) Applicant’s profession 3) Applicant’s Address 4) Name of the Factory 5) Full Postal address of the factory 6) Situation of the factory a) Town / Village b) Subdivision c) District d) Nearest police station 7) Particulars of the plant to be installed :- 8) Particulars for which Plan-drawing are submitted :- (State whether initial approval/additional installation / additional construction /changes in installation etc) 9) If the plans have been approved earlier give the number and date of approval of previous plans relevant to the present plans except in the case of initial approval. 10) Total installed capacity in Horse Power. 11) Maximum number of workers proposed to be employed in the factory. Signature of the applicant with date & Seal Note: This application should be accompanied by the following documents:- (a) A flow-chart of the manufacturing process supplemented by a brief description of the process in its various stages, list of raw materials used, intermediate products including emission of toxic gases, etc., finished products, by-products, their quantities, methods of storage and handling, loading and transport and details of the arrangements for the disposal of trade waste and effluents, the likely hazards and the methods to control or eliminate them. (b) Plans, in duplicate, drawn to scale, showing – (i) the site of the factory and immediate surroundings including adjacent buildings and other structures, roads, drains etc., and (ii) the plan, elevation and necessary cross-sections of various buildings including all relevant details, relating to natural lighting, ventilation and means of escapes in case of fire. The plans shall also clearly indicate the position of the plant and machinery, aisles and passages; and (iii) such other particulars as the Chief Inspector may require. Form 6 (See rules 7) APPLICATION FOR REGISTRATION AND GRANT OR RENEWAL OF FACTORY LICENCE AND NOTICE OF OCCUPATION (FOR THE YEAR… ................................................................................................................................................ ) ( to be submitted in triplicate) 1) Name of the Factory 2) Factory Licence number, if already registered 3) Full Postal address of the factory 4) Postal Address to which communication relating to the factory should be sent 5) Names of items manufactured / to be manufactured (principal product & other product) a) in the factory in the last twelve months (in case of factories already in existence); and b) in the factory during next twelve months (in case of all factories) 6) a) Maximum number of workers proposed to be employed on any one day during the year. b) Numbers of workers to be ordinarily employed in the factory. 7) Nature and amount of power to be used (in KW or H.P) i) Installed or ii) Proposed to be installed 8) Full Name and residential address of the person who shall be the Manager of the factory for the purpose of the Act & Rules. 9) Full name and residential address of the Occupier - a) the proprietor of the factory in case of a private firm of proprietary concern. b) the partners in case of partnership firm. c) the Directors in case of public limited company or firm. d). the Directors in case of private limited company or firm. e). the Shareholders in case of a private company f). the Chief Administrative Head in case of Government factory or a factory run by local authority or by any statutory corporation or by body. g) president / secretary and other shareholders in case of Co-op. society. 10). Full name and Address of the owner of the premises or building including the precincts thereof referred to in Section 93. 11). a) Reference number and date of approval of the plans for site whether for old or new building or for construction or extension of factory by the Chief Inspector; and b). Reference number and date of approval of the arrangements, if any, made for disposal of trade wastes and effluents and the name of authority granting such approval. 12). a). Amount of fee paid : Rs. …………………………. b).Challan Number & date of payment in Treasury ( Original copy of Challan to be enclosed) Signature of Manager Signature of Occupier Date Date Note :- 1). This form should be completed in Ink in Block letters or typed. 2). If any of the persons named against item no.9 is minor, the fact should be clearly stated. Form 7 ( Prescribed under Rule – 8,9,11) GOVERNMENT OF TRIPURA FACTORIES & BOILERS ORGANIZATION LICENCE TO WORK A FACTORY Registration No. …………….. Date of Reg. …………… Licence is hereby granted to for the premises known as situated at for use as a factory within the limits stated hereinafter, subject to provisions of the Factories Act, 1948, and the rules made there under. The ……………….20…. Chief Inspector of Factories (Issuing authority) Calendar Year Valid For Fee Date of Payment Excess fee for late payment Date of payment Signature of the Issuing Authority Maximum number of workers on any one day Maximum Installed Power / Capacity in KW or HP or KVA Granted Under Rule 7 Renewed Under Rule9 TRANSFERS To whom transferred Year of transfer Date of payment of Transfer fee Signature of the Issuing Authority AMENDMENTS Year when Amended Amended Date of payment of amendment fee Additional fee Date of Payment Signature of the Issuing Authority Workers Installed Power Capacity in Kilowatts Form 8 ( See Rule 19) NOTICE OF CHANGE OF MANAGER 1) Full Name of the Factory 2) License No 3) Full Postal Address 4) Name of Outgoing Manager 5) a) Full name of New Manager b) Age c) Details of immediate previous Employment (State name of the Employer , Place of Work, period of employment, nature of work) d) Permanents Address with Telephone no, if installed e) Present address with Telephone no, if installed. f) Date of Appointment of the New Manager Specimen Signature of the New Manager Date Place Signature of the Occupier Form 10 [See rule 25(2)] CERTIFICATE OF FITNESS 1 (a) Serial no (b) date 2. Name of the Person examined 3. Father’s Name 4. Sex 5. Residence 6. Date of Birth 7. Physical fitness 8. Descriptive marks 9. Reason for a) refusal of Certificate b) Certificate being Signature or left hand thumb impression of the person examined Initials of Certifying Surgeon Serial No Date I Certify that I have personally examined Sri/Smt ………………………………………... Son/daughter of …………………………… residing at …………………………………… ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… who is desirous of being employed in a factory, and that his /her age, as nearly as can be ascertained from my examination is .............. yrs, and that he/she is fit for employment in factory as an adult/child. His/Her descriptive marks are ……………….. ……………………………………………… ……………………………………………… ……………………………………………… ……………………………………………… Signature or left hand thumb impression of the person examined Signature of Certifying surgeon Form 12 (See rule 67, 68) REGISTER OF WORKERS EMPLOYED FOR WORK ON OR NEAR MACHINERY IN MOTION 1). Name of worker 2). Serial no as in the register of workers under section 62 3). Father’s Name 4). Date of Birth 5). Department 6). Nature of work 7). Qualification or period of service on similar work 8). Date when tight fitting clothing was provided 9). Remarks I certify that above mentioned worker whose signature or left thumb impression is given below is a properly trained male adult worker who is competent to mount or slip belts, lubricate and other adjusting operations on the machinery installed in my factory while they are in motion. Signature of left hand thumb impression of worker Signature of Occupier / Manager Form 13 (See Rule 72) REPORT OF EXAMINATION OF HOISTS AND LIFTS 1. Name of Occupier with Address 2. Name of Manager 3. (a)Type of hoist or lift identification number or description (b)Date of Construction or re- construction (if ascertainable) 4. Are all parts of the hoist or lift of good mechanical construction, sound material and adequate strength (so far as ascertainable). 5. Are the following parts of the hoists or lift properly maintained and in good working order ? If not, state what defects have been found. (a) Enclosure of hoist-way or lift-way (b) Landing gates and cage gates (c) Interlocks and the landing gates and cage gate(s) (d) Other gate fastenings (e) Cage and platform and fittings, guides, buffers, interior of the hoist way or life– way. (f) Overrunning devices (g) Suspension ropes or chain and their attachments (h) Safety gears i.e., arrangements for preventing fall of platform or cage breaks (i) Brakes (j) Worm or Spur gearing (k) Other electrical equipment (l) Other parts 4). What parts (if any) where inaccessible? 5). Repairs, renewals or alternation (if any) required and period within which they should be executed. 6). Maximum safe working load subject to repairs, renewals or alterations ( If any ) specified in item (5). 7). Other particulars I/we certify that on (date) ................................ I/We thoroughly examined this hoist or lift and that the above is a correct report of result. Signature Qualification Address Date (If employed by a company or association, name and address of the company or association). Form 15 [See Rule 74(9) (b)] REPORT OF EXAMINATION OR TEST OF PRESSURE VESSELS OR PLANT 1. Name and address of factory :- 2. Name, description and distinctive number of Pressure Vessel or Plant :- 3. Name and address of manufacturer and reference to their test certificate or certificate of competent person 4. Nature of process in which pressure vessel or plant is used 5. Particulars of Pressure Vessel or Plant a). Date of Construction b). Thickness of walls c). Date on which the pressure vessel or plant was first taken into use d). Maximum possible working pressure recommended by the manufacturer e). Safe working pressure recommended by the manufacturer 7). Date of last – (i) external examination (ii) internal examination (iii) hydraulic examination (iv) ultrasonic test 8). Whether lagging was removed for purposes of examination 9). What parts ( if any) were inaccessible? 10) Description of examination carried out and findings— (i) External examination (give reasons if it is not carried out six monthly) (ii) Internal examination (give reasons if it is not carried out annually) (iii) Hydraulic test (give reasons if it is not carried out at interval of 2 years or 4 years) (iv) Ultrasonic test ( please quote number and date of the certificate issued by Chief Inspector, permitting ultrasonic test in lieu of internal examination and hydraulic test). 11) Safe working pressure calculated as per methods given in sub-rule 5©(ii) for sizing cylinders - 12). Condition of pressure vessel or Plant – (a) Vessel (b) Piping 13). Condition of fittings and appliances (i) Pressure Gauges (ii) Safety Valve (iii) Stop Valve (iv) Reducing valve (give reasons if not necessary) (v) Additional safety valve (required in case reducing valve is necessary) (vi) Other devices (please specify particularly in case of jacketed vessels). 14) Safe working pressure recommended by after examination 15) Specify repairs, if any, and periods within which they should be executed. 16) Specify reduced working pressure pending repairs. 17. Other observations / conditions subject to which the plant is to be operated I certify that on (date) .......................... the pressure vessel or plant described above was thoroughly cleaned and ( sor far as its construction permits) made accessible for through examination and for such tests as were necessary for the rough examination and that on the said date, I thoroughly examined this pressure vessel or plant, including its fittings, and that the above is a true report of my examination. Signature :- Qualification :- Address :- Date :- (If employed by a company or association, name and address of the company or association). Form 16 (See Rule 75(8)(b)) REGISTER OF EXAMINATION OF GASHOLDERS Signature of the occupier /Manager Distingu ishing number or letter of gas holder Particulars of Manufacture Particulars of examination carried out under sub-rules 75(4) and (5) Particulars of repair Remarks Maker’s Name Date of Manufa cture Number of lifts Maximum Capacity in cubic meters Pressure thrown by gas holder when full of gas Method of examin ation used Date of examin ation Name and designati on of the person making this examina tion Nature of repairs Date of repairs and painting By when repairs are carried out 1 2 3 4 5 6 7 8 9 10 11 12 13 Form 17 [See Rule 75(8)(c)] REPORT OF EXAMINATION OF WATER-SEALED GAS HOLDER 1. Name of occupier and factory : 2. Situation and address of factory : 3. Name, description, distinguishing number or letter and type of gas holder. 4. Name and address of the manufacturer 5. (a) Number of lifts (b) Maximum capacity in cubic meters. (c) Pressure thrown by holder when full of gas 6. Particulars of gas to be stored in the holder 7. Particulars as to the condition of (A) Crown (B) Side shooting, including grips and cups (C) Guiding Mechanism (Roller carriages, rollers, pins, guide rails or ropes) (D) Tank and (E) Other structure, if any (columns, framing and bracing) 8. Particulars as to the position of the lifts at the time of examination 9. Particulars as to whether the tank and lifts were found sufficiently level for safe working and if not, as to the steps taken to remedy the defect 10. Date of examination and by whom it was carried out 11) Condition of Vessel a) External b) Internal 12) a) Are all fitting and appliances properly maintained and in good condition ? b) Repairs if any, required and period within which they should be executed (c) Any other condition which the person making the examination thinks it necessary for securing safe working 13) Other observations I certify that on ( date) .................... the gasholder described above was thoroughly examined and such of the tests as were necessary made on the same day and that the above is a true report of any examination Signature : Qualification Address Date (If employed by company or association, name and address of the association) Form 18 (See rule 96) RECORD OF EYE EXAMINATION Serial Numb er Departme nt/ works Nam e of the work er Se x Age (on last birthda y) Occupation Examinatio n of eyesight Signature of ophthalmolo gist Remar ks Natu re Date of employm ent Dat e Resu lt 1 2 3 4 5 6 7 8 9 10 11 Form 18A (Prescribed under rule –99) FORMAT OF APPLICATION TO THE SITE APPRAISAL COMMITTEE 1. Name and address of the applicant 2. Site Ownership Data Revenue details of site such as Server No. Plot No. etc Whether the site is classified as forest and of so, whether approval of the Central Government under section 5 of the Indian Forests Act, 1927 has been taken. whether the proposed site attracts the provisions of section 3(2) (v) of the E.P Act, 1986. If so , the nature of the restrictions. Local authority under whose jurisdiction the site is located. 3. Site Plan Site plane with clear identification of boundaries and total area proposed to be occupied and showing the following details nearby the proposed site. a) Historical monument, if any, in vicinity. b) Name of neighboring manufacturing units and human habitats educational and training institutions, petrol installations, storage of LPG and other hazardous substance in the vicinity and their distance from the proposed unit. c) Water sources (river streams, canals, dams, water filtration plants, etc.) in the vicinity. d) Nearest Hospitals, Fire-station, civil defence station and police stations and their distances. e) High tension electrical transmission lines, pipe line for water, oil, gas or sewerage; railway lines, Roads, stations, jetties and other similar installations. 3.2 Details of soil conditions and depth at which hard strata obtained. 3.3 Contour map of the area showing nearby hillocks and difference in levels. 3.4 Plot plan of the factory showing the entry and the exit points, roads within, water drains etc. 4. Project Report 4.1 A summery of the salient features of the project. 4.2 Status of the organization ( Govt., Semi-Govt, Public or Private etc.) 4.3 Maximum number of persons likely to be working on the factory. 4.4 Maximum amount of power and water requirements and source of their supply. 4.5 Block diagram of the buildings and installations for the proposed supply. 4.6 Details of housing colony, hospital, school and other structural facilities proposed. 5. Organisation structure of the proposed manufacturing unit/factory 5.1Organisation diagrams of - Proposed enterprise in general. - Health, Safety and Environment protection departments and their linkage to operation and technical departments. 5.2 Proposed Health and Safety policy. 5.3 Area allocation for treatment of Wastes and Effluent. 5.4 Percentage outlay on safety, health and environment protection measures. 6. Meteorological data relating to the site. 6.1 Average, minimum and maximum of - Temperature - Humidity - Wind velocities, during the previous ten years. 6.2 Seasonal variations of wind direction 6.3 Highest water level reached during the floods in the area recorded so far. 6.4 Lightening and seismic data of the area. 7. Communication links 7.1 Availability of telephone/ telex/ wireless and other communication facilities for outside communication. 8. Manufacturing Process Information 8.1 Process flow diagram 8.2 Brief write-up on process and technology. 8.3 Critical process parameters such as pressure build-up, temperature rise and run-away reactions. 8.4 Other external effects critical to the process having safety implications, such as ingress of moisture or water. 8.5 Highlights of the build-in safety/ pollution control devices or measures/ incorporated in the manufacturing technology. 9. Information of Hazardous Materials 9.1 Raw materials, intermediates, products and by-products and their quantities. Enclose Material Safety Data Sheet (MSDS) in respect of each hazardous substance. 9.2 Main and intermediate storages proposed for raw materials/ intermediates/ products/ by- products (maximum quantities to be stored at any time). 9.3 Transportation methods to be used for materials inflow and outflow, their quantities and likely routes to be followed. 9.4 Safety measures proposed for: - handling of materials. - internal and external transportation; and - disposal (packing & forwarding of finished products) 10. Information on Dispersal/ Disposal of Wastes and pollutants 10.1 Major pollutants (gas, liquid, solid) their characteristics and quantities (average and at peak loads) 10.2 Quality and quantity of solid pollution problems anticipated and the proposed measures to control the same, including treatment and disposal of effluent. 11. Process Hazards Information 11.1 Enclose a copy of the report on environmental impact assessment. 11.2 Enclose a copy of the report on Risk Assessment study. 11.3 Published (open or classified) reports, if any, on accident situations/ occupational health hazards or similar plants elsewhere (within or outside the country). 12. Information of proposed Safety and Occupational Health Measures 12.1 Details of fire fighting facilities and minimum quantity of water, CO2 and or other fire fighting measures needed to meet the emergencies. 12.2 Details of in-house medical facilities proposed 13. Information on Emergency Preparedness 13.1 On site emergency plan 13.4 Proposed arrangements, if any, for mutual aid scheme with the group of neighboring factories. 14. Any other relevant information I certify that the information furnished above is correct to best of my knowledge and nothing of importance has been concealed while furnishing it. Name and signature of applicant FORM 19 [See rule 136 (4) (a)] REGISTER OF COMPENSATORY HOLIDAYS Signature of Manager of the factory Sl. No. Number in the register of workers Name Group or relay number Number and date of exempting order Year Weekly rest days lost due to the exempting order in Date of compensatory holiday given in Lost rest days carried to the next year Rema- rks January to March April to June July to September October to Decemb er January to March April to June July to Septemb er October to Decemb er 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FORM 20 (See Rule 137) OVERTIME MUSTER ROLL FOR EXEMPTED WORKERS Month ending ………………………….20……… Number in the register of adult workers Name of exempted worker Department Dates on which overtime has been worked Extent of overtime on each occasion Total overtime hours worked or production in case of piece workers Normal hours Normal rate of pay for piece work or rate or pay per hour Over time rate of pay Normal earnings Overtime earning earnings Total earnings Date on which overtime payments made. 1 2 3 4 5 6 7 8 9 10 11 12 13 FORM 21 (Prescribed under Rule 140) NOTICE OF PERIODS OF WORK FOR ADULT Name of factory …………………….. Place ......................................... District------------- …………………………… Periods of works group Men Women Description of groups Remarks Total number of men employed Total number of Women employed Relays A B C D A B C D Group letter Nature of work 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 On Working From – To – From – To – From – To On partial working days From – To - From – To - Date on which this notice is first exhibited: …………… (Signature of Manager) FORM 22 (Prescribed under Rule 141) REGISTER OF ADULT WORKERS Serial Numb er Na me Resident ial address Father ’s Name Natu re of work Letter of group as in Form_ 21 Numb er of relay if worki ng in shifts Number and date of certificate if an adolescent Remar ks Number of Certific ate and date Token Numbe r giving referen ce 1 2 3 4 5 6 7 8 9 10 ----------------- (Signature of Manager) FORM 23 (see Rule 146) NOTICE OF PERIODS OF WORK FOR CHILD WORKERS Name of Factory Place District_____ Period of Work Children Total number of Children employed Description of group Remarks Groups A B C Group Letter Nature of work Relays 1 2 1 2 1 2 From To Date on which this notice is first exhibited Signature of Manager Date: - FORM 24 (see Rule 147) REGISTER OF CHILD WORKERS Seri al No. Na me Resident ial Address Father ’s Name Date of first employm ent Numbe r of certific ate and its date Token number giving referen ce to certific ate Lett er of grou p as in For m 23 Numb er of relay, if worki ng in shifts Remar ks 1 2 3 4 5 6 7 8 9 10 Signature of Manager Date: - FORM 25 (see Rule 148) REGISTER OF LEAVE WITH WAGES Part I Part II - Adults - Children Factory :- Department:- Name of Worker Father’s Name : - : - Sl. No. Serial Number in the register of adult/ child workers Date of entry into service Interruptions Leave due with effect from Whether leave not desired during the next 12 months Date from which the worker is allowed leave Wages for leave paid in Discharged worker Rem- arks Sickness and accident Authori- sed leave Lockout or legal strike Involun tary unempl oyment Others Date of discharge Date and amount of payment made in lieu of leave 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Note :- Separate page shall be allotted to each worker. ___________________ (Signature of Manager) FORM 26 (See Rule 149) Leave book Factory: - Name of Worker: - Department: - Father’s Name: - Sl. No. Serial Number in the register of adult/ child workers Date of entry into service Interruptions Leave due with effect from Whether leave not desired during the nest 12 months Date from which the worker is allowed leave Wages for leave paid in Discharged worker Rem- arks Sickness and accident Authori -sed leave Locko ut or legal strike Involunt- ary unemp- loyment Others Date of discharge Date and amount of payment made in lieu of leave 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Note :- The leave book shall be made out separately for each worker on thick bonds sheets. Signature of Manager FORM 27 (see Rule 155) NOMINATION FOR PAYMENT OF PAY DUE FOR PERIOD OF HOLIDAYS IN THE EVENT OF DEATH OF WORKER I hereby require that in the event of my death before resuming work, the balance of my pay due for the period of holidays shall be paid to who is my and resides at Witnesses: Attested Signature Signature or left hand Designation thumb impression of worker : - Address Signature Particulars or worker such as serial number Name in the register of adult/ child Designation workers Section or address Department, etc. Date : FORM 28 (Prescribed under various schedules to Rule 160) CERTIFICATE OF FITNESS Serial No…………………… I certify that I have personally examined (name) son of residing at who is desirous of being employed as (designation) in (process, department and factory) and that his age, as nearly as can be ascertained from my examination, is years, and that he is, in my opinion, fit / unfit for employment in the above mentioned factory as mentioned above. 2. He may be produced for further examination after a period of . 3. The serial number of the previous certificate is . Signature or left hand thumb impression of person examined Signature of Certifying Surgeon Date I certify that I examined the person mentioned above on I extend this certificate until (if certificate is not extended, the period for which the worker is considered unfit for work is to be mentioned) Signs and symptoms observed during examination Signature of the certifying surgeon 1 2 3 4 FORM 29 (Prescribed under various Schedule to 160) HEALTH REGISTER 1 Sl.No 2 Deptt/ Works 3 Name of Workers 4 Sex 5 Age at last birth day 6 Date of employment on present work 7 Date of leaving or transfer to other work 8 Reasons for discharge or transfer 9 Nature of job or occupation 10 Raw materials products or by- products likely to be exposed to 11 D ates D ates of m edical exam ination and the results thereof 12 R es ult Fit or U nf it 13 Signs and symptoms observed during examination 14 Nature of tests and results thereof 15 If declared unfir for work,sate period of suspension with reasons in details 16 Whether certificate of unfitness issued to the worker 17 Re-certified fit to resume duty on 18 Signature of the Certifying Surgeon with date FORM 30 [see Rule 161 (2)] REPORT OF ACCIDENT OR DANGEROUS OCCURRENCE RESULTING IN DEATH OR BODILY INJURY 1. Name of occupier (or factory)/ employer : 2. Address of works/ premises where the accident or dangerous occurrence took place : 3. Nature of industry : 4. Branch or department and exact place where the accident or dangerous occurrence took place : 5. Name and address of the injured person : 6. a) Sex : b) Age (at the last birthday) : c) Occupation of the injured person : 7. Local E.S.I.C. office to which the injured person is attached : 8. Date, shift and hour of Accident or dangerous occurrence : 9. a) Hour at which the injured person started work on the day of accident or dangerous occurrence : b) Whether wages in full or part are payable to him for the day of the Accident or dangerous occurrence. : 10. a) Cause or nature of accident or dangerous occurrence : b) If caused by machinery – i) give the name of machine and the part causing the accident of dangerous occurrence. : ii) state whether it was moved by mechanical power at the time of accident or dangerous occurrence : c) State exactly what the injured person was doing at the time of accident or dangerous occurrence : d) In your opinion, was the injured person at the time of accident or dangerous occurrence. i) acting in contravention of provisions of any law applicable to him : or ii) acting in contravention of any orders given by or on behalf of his employer : or iii) acting without instructions from his employer. e) In case reply to (d) (i), (ii) or (iii) is in the affirmative, state whether the act was done for the purpose of and in connection with the employer’s trade or business. 11. In case the accident of dangerous occurrence took place while traveling in the employer’s transport, state whether – a) the injured person was traveling as a passenger to or from his place of work : b) the injured person was traveling with the express or implied permission of his employer; c) the transport is being operated by or on behalf of the employer or some other person by whom it is provided in pursuance of arrangements made with the employer; : and d) the vehicle is being/ not being operated in ordinary course of public transport service : 12. In case the accident or dangerous occurrence took place while meeting emergency, state a)its nature; and b)whether the injured person at the time of accident or dangerous occurrence was employed for the purpose of his employer’s trade or business in or about the premises at which the accident or dangerous occurrence took place. 13. Describe briefly how the accident or dangerous occurrence took place : 14. Name and address of witnesses : (1) (2) 15. a) Nature and extent or injury (e.g. fatal, loss of finger, facture of leg, scald, scratch followed by sepsis, etc.) : b) Location of injury (e.g., right leg, left hand, left eye, etc.) : 16. a) If the accident or dangerous occurrence not fatal,. State whether the injured person was disabled for more than 48 hrs: b) Date and hour of return of work : 17. a) Physician, dispensary or hospital from whom or in which the injured person received or is receiving treatment : b) Name of dispensary/ panel doctor elec- ted by the injured person : 18. a) Has the injured person died? : b) If so, date of death : I certify that to the best of my knowledge and belief the above particulars are correct in every respect. Signature of Manager/ Employer : Name, Designa tion and address of manager/ employer : Date of dispatch of report : …………………………………………………………………………………………… . (This space is to completed by the Inspector of Factories) District …………………………………………… : Date or receipt : Name of the accident Causation : or dangerous occurrence : Other particulars (e.g. fatal, leg injury, arm injury, etc) : Date of investigation : Result of investigation : FORM 31 [see Rule 161 (2)] REPORT OF DANGEROUS OCCURRENCE WHICH DOES NOT RESULT IN DEATH OR BODILY INJURY 1. Name and address of factory : 2. Name of Occupier : 3. Name of Manager : 4. Nature of industry : 5. Branch or department and exact place where the dangerous occurrence took place : 6. Date and hour of dangerous occurrence : 7. Nature of dangerous occurrence (State exactly what happened) : I certify that to the best of my knowledge and belief the above particulars are correct in every respect. Signature of manager : Name, designation and address of manager : Date of dispatch of report : (To be completed by the Inspector of Factories) District …………………………………………… : Date or receipt : Name of the accident Causation : or dangerous occurrence : Other particulars (e.g. fatal, leg injury, arm injury, etc) : Date of investigation : Result of investigation : FORM 32 [see Rule 161(4)] REPORT OF FURTHER DETAILS OF ACCIDENT (To be sent to the Inspector of Factories within 28 days of the occurrence of the accident and once every fortnight thereafter as necessary until the final report on the date of return to work of the person injured is made.) 1. Registration number of the factory : - 2. Name & address of the Factory : - 3. Name of the person injured : - 4. Date and hour of accident : - 5. Date of return to work : - 6. Number of days the person injured was away from work : - 7. Details of disablement, if any : - 8. Percentage loss of earning capacity if any (give reference to the medical certificate and enclose copy of the same) : - 9. Details of payment of disablement benefit where such payment is made by the employer himself : - 10. If the person is still undergoing treatment, state present position, where he is undergoing treatment, when he is likely to be fit to resume work, etc. : - 11. Any other relevant information : - I certify that to the best of my knowledge and belief the above particulars are correct in every respect. Signature of Manager (Name in Block letters) FORM 33 (see Rule 162) NOTICE OF POISONING OR DISEASE (See instructions on reverse) 1. Name of factory with address : - 2. Factory Registration Number : - 3. Occupiers’ Office address : - 4. Occupiers’ residential address : - 5. Nature of Industry : - 6. Name and works number of patient : - 7. Residential address of patient : - 8. Sex and Age of Patient : - 9. Precise occupation of patient : - 10. Nature of poisoning or disease from which patient is suffering : - 11. Has the case been reported to the Inspector of Factories and the Certifying Surgeon? : - Full Signature of Manager/ Occupier with seal and Date : …………………………………………………………………………………………… …………………… (To be filled in by the Chief Inspector) Number of the case : Remarks : …………………………………………………………………………………………… …………………… Notice of Poisoning or Disease (Extract from the Factories Act, 1948 (Section 89) Where any worker in a factory contracts any disease specified in the schedule, the manager of the factory shall send a notice thereof to such authorities, and in such form and within such time, as may be prescribed. SCHEDULE LIST OF NOTIFIABLE DISEASES 1. Lead poisoning, including poisoning by any preparation of lead or their sequelae. 2. Lead tetra-ethyl poisoning. 3. Phosphorous poisoning or its sequelae. 4. Mercury poisoning or its sequelae. 5. Manganese poisoning of its sequelae. 6. Arsenic poisoning or its sequelae. 7. Poisoning by nitrous fumes. 8. Carbon disulphide poisoning. 9. Benzene poisoning, including poisoning by any of its homologues, their nitro or amide derivatives or its sequel. 10. Chrome ulceration or its sequelae. 11. Anthrax. 12. Silicosis. 13. Poisoning by halogen derivatives of the hydrocarbons of the aliphatic series. 14. Pathological manifestations due to – a) radium or other radio-active substances; and b) x-rays 15. Primary epitheliomatous cancer of skin. 16. Toxic anemia. 17. Toxic jaundice due to poisonous substances. 18. Oil acne or dermatitis due to mineral oils and compounds containing mineral oil base. 19. Byssinosis 20. Asbestosis 21. Occupational or contract dermatitis caused by direct contract with chemicals and paints. These are of two types that is, primary irritants and allergic sensitizers. Extract from the Tripura Factories Rules, 2007 (Rule 162) A notice in Form 33 should be sent forthwith both to the Chief Inspector and to the Certifying Surgeon, by the manager of a factory if factory in which there occurs a case of lead, phosphorous, mercury, manganese, arsenic, carbon bi-sulphide or benzene poisoning; or of poisoning by nitrous fumes or by halogens or hologen derivatives of the hydrocarbons of aliphatic series; or of chrome ulceration, anthrax, silicosis, toxic anemia, toxic jaundice, primary epitheliomatous cancer of skin, or of pathological manifestations due to radium or other radio-active substances or x-rays. FORM 34 (see Rule 164) ABSTRACT OF THE FACTORIES ACT, 1948 AND THE TRIPURA FACTORIES RULES, 2007 (To be affixed in a conspicuous and convenient place at or near the main entrance to the factory) Interpretation 1. “Factory” means any premises including the precincts thereof – i) Wherein ten or more workers are working, or were working on any day of the proceeding twelve months, and in any part of which a manufacturing process is being carried on with the aid of power, or is ordinarily so carried on, or ii) Wherein twenty or more workers are working, or were working on any day of the proceeding twelve months, and in any part of which manufacturing process is being carried on without the aid of power, or is ordinarily so carried on. but does not include a mine subject to the operation of the Mines Act, 1952 (35 of 1952), or a mobile unit belonging to the Armed Forces of Union, a railway running shed or hotel restaurant or eating place. Explanation: - For computing the number of workers for the purposes of this clause all the workers in different relays in a day shall be taken into account. 2. “Worker” means a person employed, directly or through any agency (including a contractor) with or without the knowledge of the principal employer, whether for remuneration or not, in any manufacturing process, or in cleaning any part of the machinery or premises used for a manufacturing process, or in any other kind of work incidental to, or connected with, the manufacturing process, or the subject of the manufacturing process; but does not include any member of the armed forces of the Union. 3. “Manufacturing Process” means any process for – i) making, altering, repairing, ornamenting, finishing, packing, oiling, washing, cleaning, breaking up, demolishing, or otherwise treating or adapting any article of substance with a view to its use, sale, transport, delivery or disposal, or ii) pumping oil, water, sewage or any other substances; iii) generating, transforming or transmitting power; or iv) composing types of printing, printing by letter press, lithography, photogravure or other similar process or bookbinding; or v) constructing, reconstructing, repairing, refitting, finishing or breaking up ships or vessels; or vi) preserving or storing any article in cold storage. Working hours, holidays, intervals after rest, etc. 4. Hours of work for adults (Sections 51 and 54). – No adult worker shall be required or allowed to work in a factory for more than 48 hours in any week and for more than 9 hours in any day. 5. Relaxation of hours of work for adults (Section 64). – The ordinary limits on working hours may be relaxed in certain special cases, e.g., workers engaged on urgent repairs; in work in the nature or preparatory or complementary work which must necessarily be carried on outside the limits laid down for the general working of the factory; in work which is necessarily so intermittent that the intervals during which they do not work while on duty ordinarily amount to more than intervals for rest; in any work which for technical reasons must be carried on continuously; in making or supplying articles of prime necessity which must be made or supplied every day; in a manufacturing process which cannot be carried on except during fixed seasons, or at times dependent on the irregular action of natural forces; in engine rooms or boiler houses or in attending to power plant or transmission machinery; in the printing of news papers, who are held up on account of the breakdown of machinery; in the loading or unloading of railway wagons or lorries or trucks; and in any work which is notified by the State Government in the Official Gazette as a work of national importance. Except in the case of urgent repairs, the relaxation shall not exceed the following limits of work inclusive of overtime: - i) the total number of hours of work in any day shall not exceed ten. ii) the spread over inclusive of intervals for rest, shall not exceed 12 hours in any one day; iii) the total number of hours of work in a week including overtime, shall not exceed sixty; iv) the total number of hours of overtime work shall not exceed fifty for any one quarter. 6. Payment for overtime (section 59): Where a worker works in a factory for more than 9 hours in any day or for more than 48 hours in any week, he shall, in respect of overtime work, be entitled to wages at the rate of twice his ordinary rate if wages. 7. Exemption of supervisory staff (section 64): - Chapter IV, other than the provisions of clause (b) of sub section (1) of section 66 and the proviso to that sub-section, of the Act -- working hours of adults does not apply to persons holding position in a factory-management or are employed in confidential position in a factory management provided that where the ordinary rate of wages of such person does not exceed rupees seven hundred and fifty per month, they are entitled to extra wages in respect of overtime work under Section 59. 8. Weekly holiday (Adults) (Section 52). – No adult worker shall be required or allowed to work in a factory on the first day of the week, unless – a) he has, or will have, a holiday for a whole day on one of the three days immediately before or after the said day, and b) the manager of the factory has, before the said day or the substituted day under clause (a) which is earlier. i) delivered a notice at the office of the Inspector of his intention to require the worker to work on the said day and of the day which is to be substituted; and ii) displayed a notice to that effect in the factory; Provided that no substitution shall be made which will result in any worker working for more than ten days consecutively without a holiday for a whole day. 9. Compensatory holidays (Section 53). – Where a worker in a factory, as a result of exemption from the ordinary provision relating to weekly holidays, is deprived of any of the weekly holidays, he shall be allowed, within the month in which the holidays were due to him or within the two months immediately following that month, compensatory holidays of equal number of the holidays so lost. 10. Intervals for rest for adults (Section 55 and 56).- The periods of work of adult workers in a factory each day shall so fixed that no period shall exceed 5 hours before he has had an interval for rest of at least half an hour and that inclusive of his intervals for rest they shall not spread over more than ten and a half hours in any day or, with the permission of the Chief Inspector of Factories in writing, 12 hours. 11. Prohibition of double employment (Section 60, 71 & 99) – No child or, except in certain circumstances, an adult worker, shall be required or allowed to work in any factory on any day on which he has already been working in any other factory. If a child works in a factory on any day on which he has already been working in another factory, the parent or guardian of the child or the person having custody of or control over him or obtaining any direct benefit from his wages, shall be punishable with fine, which may extend to Rs. 50 unless it appears to the court that the child so worked without the consent of connivance of such parents, guardian or person. 12. Prohibition of employment of children under 14 (Section 67). – No child who has not completed his fourteenth year shall be required or allowed to work in any factors. 13. Hours of work for children (Section 71) – No child shall be employed or permitted to work in any factory for more than four and a half hours in any day and during the period of at least twelve consecutive hours which shall include the interval between 10 P.M. and 6 A.M. The periods of work of all children employed in a factory shall be limited to two shifts which shall not overlap or spread over more than 5 hours each and each child shall be employed in only one of the relays. The provision relating to weekly holidays shall also apply to child workers and no exemption from this provision may be granted in respect of any child. 14. Prohibition of employment of women (Section 66) – No woman shall be required or allowed to work in any factory except between the hours of 6 A.M. and 7 A.M. The State Government may vary these limits or exempt this restriction in case of women working in fish-curing or fish-canning factories. Leave with Wages 15. Leave with wages (Section 79, 80 and 83 and Rules). – Every worker who has worker for a period of 240 days or more in a factory during a calendar year shall be allowed during the subsequent calendar year leave with wages for a number of days calculated at the rate of - i) if an adult, one day for every twenty days of work performed by him during the previous calendar year; and ii) if a child, one day for every 15 days of work performed by him during the previous calendar year. Explanation. 1. – For the purpose of this sub-section – a) any days of lay off, by agreement or contract or as permissible under the standing orders; b) in the case of female worker, maternity leave for any number of days not exceeding twelve weeks; and c) the leave earned in the year prior to that in which the leave is enjoyed; shall be deemed to be days on which the worker has worked in a factory for the purpose of computation of the period of 240 days or more, but he shall not earn leave for these days. Explanation 2 – The leave admissible under this sub-section shall be exclusive of all holidays whether occurring during or at either end of the period of leave. For the leave allowed to him, a worker shall be paid at a rate equal to the daily average of his total full-time earnings, for the days on which he actually worked during the month immediately preceding the leave exclusive of any overtime and bonus, but inclusive of dearness allowance and the cash equivalent of the advantage accruing through the concessional sale to the worker of food grains and other articles. A worker whose service commences otherwise than on the first day of January shall be entitled to leave at the rate indicated above, if he has worked for two–thirds of the total number of days in the remainder of the calendar year If a worker is discharged or dismissed from service or quits his employment or is superannuated or dies while in service, during the course of the calendar year, he or his heir or nominee as the case may be, shall be entitled to wages in lieu of the quantum of leave to which he was entitled immediately before his discharge, dismissal, quitting of employment, superannuation or death, calculated at the rates specified above, even if he had not worked for the entire period specified above. Such payment shall be made – i) Whether the worker is discharged or dismissed or quits employment, before the expiry of the second working day from the day of such discharge, dismissal or quitting; and ii) Where the worker is superannuated or dies while in service, before the expiry of two months from the date of such superannuation or death. If the employment of a worker who is entitled to leave with wages is terminated by the occupier before he has taken the entire leave to which he is entitled, or if having applied for and having not been granted such leave, the worker quits his employment before he has granted such leave, the occupier of the factory shall pay him the amount payable in respect of the leave not taken, and such payment shall be made before the expiry of the second working day after the day on which his employment is terminated and a worker who quits his employment, on or before the next pay day. The manager shall maintain a register of leave with wages in the prescribed Form 20 and shall provide each worker with a book called the ‘Leave Book’ in the prescribed From 21. The leave book shall be the property of the worker and the manager or his agent shall not demand it except to make entries of the dates of holidays or interruptions in service, and shall mot keep it for more than a week at a time. If a worker loses his leave book, the manager shall provide him with another copy on leave book on payment of Rs.2/= and shall complete it from his record. Health 16. Cleanliness (Section 11). – Except in cases specially exempted, all inside walls and partitions, all ceilings or tops of rooms and all walls, sides and taps of passages and stair- cases in a factory shall be kept whitewashed or colour-washed. The whitewashing or colourwashing shall be carried out at least once in every period of fourteen months. The floor of every workroom shall be cleaned at least once in every week by washing, using shall be cleaned at least once in every week by washing, using shall be cleaned at least once in every week by washing, using disinfectant, where necessary, or by some other effective method. 17. Disposal of wastes and offluents (Section 12). – Effective arrangements shall be made in every factory for the treatment of wastes and effluents due to the manufacturing process carried on therein, so as to render then innocuous, and for their disposal. 18. Ventilation and temperature (Section 13) – Effective and suitable provision shall be made in every factory for securing and maintained in every workroom adequate ventilation by the circulation of fresh air and such a temperature as will secure to workers therein reasonable conditions of comfort and prevent injury to health. 19. Overcrowding (Section 16). – Unless exemption has been granted, there shall be in every workroom of a factory in existence on the date of commencement of this Act at least 350 cubic feet and of a factory built after the commencement of this Act at least 500 cubic feet of space for every worker employed therein, and for this purpose no account shall be taken of any space which is more than 14 feet above the level of the floor of the room. 20. Lighting (Section 17): - In every factory effective arrangements shall be made to provide and maintain at suitable points conveniently situated for all workers employed therein, a sufficient supply of wholesome drinking water. 21. In every factory wherein more than 250 workers are ordinarily employed the drinking water shall, during hot weather, be cooled by ice or other effective methods. The cooled drinking water shall be supplied in every canteen, lunchroom and restroom and also at conveniently accessible points throughout the factory. 22. Latrines and urinals (Section 19 and Rules). – In every factory sufficient latrine and urinal accommodation of the prescribed types (separate enclosed accommodation for male and female workers) shall be provided conveniently situated and accessible to workers at all times while they are at the factory. Every latrine shall be under cover and so partitioned off as to secure privacy and shall have a proper door and fastenings. Sweepers shall be employed whose primary duty it would be to keep clean latrines, urinals and washing places. 23. Spittoons (Section 20). – In every factory, there shall be provided a sufficient number of spittoons of the type prescribed in convenient places and they shall be maintained in a clean and hygienic condition. No person shall spit within the ‘premises of a factory except in the spittoons provided for the purpose. Whoever spits in contravention of this provision shall be punishable with fine not exceeding five rupees. Safety 24. Fencing of machinery (Section 21): - In every factory dangerous parts of machinery e.g., every moving part of a prime mover and every flywheel connected to a prime mover, etc. shall be securely fenced by safeguards of substantial construction which shall be constantly maintained and kept in position while the parts of machinery they are fencing are in motion or in use. 25. Work on or near machinery in motion (Section 22). – No woman or young person shall be allowed in any factory to clean, lubricate or adjust any part of a prime mover or any transmission machinery while the prime mover or the transmission machinery is in motion, or to clean, lubricate or adjust any part of any machine if the cleaning, lubrication or adjustment thereof would expose the woman or young person to risk of injury from any moving part either of that machine or of any adjustment machinery. 26. Employment of young persons on dangerous machines (Section 23). – No young persons shall work at any machine declared to be dangerous unless he has been fully instructed as to the dangerous arising in connection with the machine and the precautions to be observed and has received sufficient training in work at the machine or is under adequate supervision by a person who has thorough knowledge and experience of the machine. 27. Casing of new machinery (Section 26). – In all machinery driven by power and installed in any factory after the commencement of this Act. Every set screw, bolt or key on any revolving shaft, spindle, wheel or pinion shall be so sunk, encased or otherwise effectively guarded as to prevent danger; all spur, worm and other toothed or friction gearing which does not require frequent adjustment while in motion shall be completely encased, unless it is so situated as to be as safe as it would be if it were completely encased. Whoever sells or lets on hire or, as agent of a seller or hirer, causes or procedures to be sold or let on hire, in a factory any machinery driven by power which does not comply with these provisions or any rules made under this section, shall be punishable with imprisonment for a term which may extend to three months or with fine which may extend to five hundred rupees or with both. 28. Prohibition of employment of women and children near cotton openers (Section 27) – No woman or child shall be employed in any part of a factory for pressing cotton in which a cotton opener is at work.

Previous and next

All provisions of Tripura Factories Rules, 2007

Questions people ask

Is rule 27 of Tripura Factories Rules, 2007 still in force?

No repeal of Tripura Factories Rules, 2007 is recorded.