LawGrids logoLAWGRIDS.ORG

Rule 19, Tripura Factories Rules, 2007: Exemptions

Tripura Factories Rules, 2007 - Rule 19

Text of rule 19

Exemptions

19. Exemptions. – Paragraphs 12, 14, 15 and 16 shall not apply to any woodworking machine in respect of which it can be proved that other safeguards are provided, maintained and used which render the machine as safe as it would be if guarded in the manner prescribed in this schedule. Schedule V Rubber Mills and Plastic Mills 1. Definition – i) A “Rubber Mill” shall mean machine with rollers used in breaking down, cracking, washing, grating, mixing, refining and warming of rubber or rubber goods. A “Plastic Mill” shall mean machine with rollers used in breaking down, cracking, washing, grating, mixing, refining and warming of plastic or plastic goods. ii) A “Calendar” shall mean machine with rolls used for fractioning, sheeting, coating and breading of rubber compounds and plastic or plastic compounds. 49 2. Installation of machine: Rubber and plastic mills shall be so installed that the top of the front roll is not less than 100 cm above the floor or working level; 3. Safety devices – 1) Rubber and plastic mills shall be equipped with; a) hoppers so constructed or guarded that it is impossible for the operators to come into contact in any manner with the nip of the rolls; or b) horizontal safety-trip rods or tight wire cables across both front and rear, which will, when pushed or pulled, operate instantly to disconnected the power and apply the brakes, or to reverse the rolls. c) Safety-trip rods or tight wire cables on rubber mills shall extend across the entire length of the face of the rolls and shall be located not more than 170 cm above the floor or working level. 2) Calendar machines shall be equipped with a) Horizontal safety-trip or tight wire across both front and rear, which will when pushed or pulled operate instantly disconnect the power and apply the brakes or to reverse the roll; b) Safety-trip rods or tight wire cables on calender machines shall extend across the entire length of the face of the roll and shall be located not more than 170 cms above the floor or working level; c) on each side of all calendars and ;near both ends of the face of the rolls there shall be a vertical tight wire cable connecting with the bar tripping mechanism at the top and fastened to the frame within 30 cm of the floor. These cables should be positioned and a distance of not more than 30 cm from the face of the roll and a distance of not less than 25 mm from the calendar frame. 3. Maintenance and safety devices. – Safety trip rods and tight wire cables on all rubber mills and calendars shall be examined and tested daily in the presence of the Manager or other responsible person and if any defect is disclosed by such examination and test, the mill shall not be used until such defect has been remedied. 4. Injection Moulding Machine. – a) An electrical interlock arrangement shall be provided so that the moulds cannot be closed unless the front safety gate is fully closed and on opening the front safety gate is fully closed and on opening the front safety gate, the moulds will stop automatically. b) In addition to the above arrangement an hydraulic safety shall also be incorporated with the front safety gate. This shall prevent the tail stock mould plate from moving forward on opening of the front safety gate. c) At the rear of the machine, there shall be provided either an efficient fixed guard or a sliding gate which shall be electrically inter-locked with the movement of the mould plates in the manner of the front safety gate as required under a) above so as to prevent access to the danger zone of the moulds in motion from the rear. Schedule VI Centrifugal Machines 1. Definition. – “Centrifugal machines” include centrifugal extractors, separators and driers. 2. Every part of centrifugal machine shall be – a) of good design and construction and of adequate strength; 50 b) properly maintained; and c) examined thoroughly by a competent person at regular intervals. 3. Interlocking guard for drum or basket. – 1) The cage housing the rotating drum or basket of every Centrifugal machine shall be provided with a strong lid. The design and construction of the cage as well as the lid should be such that no access is possible to the drum or basket when the lid is closed. 2) Every centrifugal machine shall be provided with an efficient interlocking device that will effectively prevent the lid referred to in sub-paragraph (i) from being opened while the drum or basket is in motion and prevent the drum or basket being set in motion while the lid is in the open position. 4. Breaking arrangement. – Every centrifugal machine shall be provided with an effective braking arrangement capable of bringing the drum or basket to rest within as short a period of time as reasonably practicable after the power is cut off. 5. Operating speed. – No centrifugal machine shall be operated at a speed in excess of the manufacturer’s rating which shall be legibly stamped at easily visible places both on the inside of the basket and on the outside of the machine casing. 6. Exceptions. – Sub-paragraph (2) of paragraph 3, paragraphs 4 and 5 shall not apply in case of top lung machines or similar machines used in the sugar manufacturing industry. Schedule VII Power press 1. Application:- The schedule shall apply to all types of power presses including press brakes, except when used for working on hot metal. 2. Definition:- For the purpose of this Schedule – a) “approved” means approved by the Chief Inspector:- b) “fixed fencing” means fencing provided for the tools of a power press being fencing which has no moving part associated with or dependent upon the mechanism of a power and includes that part of a closed tool which acts as a guard; c) “Power press” means a machine used in metal or other industries for moulding, pressing, blanking raising drawing and similar purposes; d) “Safety device” means the fencing and any other safeguard provided for the tools of a power press. 3. Starting and stopping mechanism:- The starting and stopping mechanism shall be provided with a safety stop so as to prevent over running of the press or descent of the ram during tool setting, etc. 4. Protection of tool and die:- 1) Each press shall be provided with a fixed guard with a slip plate on the underside enclosing the front and all sides of the tool. 2) Each die shall be provided with a fixed guard surrounding its front and sides, and extending to the back in the form of a tunnel through which the pressed article falls to the rear of the press. 3) The design, construction and mutual position of the guards referred to in (1) and (2) shall be such as to preclude the possibility of the worker’s hand or fingers reaching the danger zone. 4) The machine shall be fed through a small aperture at the bottom of the die guard, but a wider aperture may be permitted for second or subsequent operations if feeding is done through a chute. 51 5) Notwithstanding anything contained in sub-clauses (1) and (2) an automatic or an inter-locked guard may be used in place of a fixed guard, but where such guards are used they shall be maintained in an efficient working condition and if any guard develops a defect, the power press shall not be operated unless the defect of the guard is removed. 5. Appointment of persons to prepare power presses for use:- 1) Except as provided in sub-paragraph (4), no person shall set, re-set, adjust or try out the tools on a power press or install or adjust any safety device thereon, being installation or adjustment preparatory to production of die proving, or carry out an inspection and test of any safety device thereon required by paragraph 8 unless he- a) has attained the age of eighteen; b) has been trained in accordance with the sub-paragraph (2); and c) has been appointed by the occupier of the factory to carry out those duties in respect of the class or description of power press or the class or description of safety device to which the power press or the safety device (as the case may be) belongs; and ; the name of every such person shall be entered in register in Form 14. 2) The training shall include suitable and sufficient practical instruction in the matters in relation to each type of power press and safety device in respect of which it is proposed to appoint the person being trained. 6. Examination and testing of power presses and safety devices:- 1) No power press or safety device shall be taken into use in any factory for the first time in that factory, or in case of a safety device for the first time on any power press, unless it has been thoroughly examined and tested in the case of power press, after installation in the factory, or in the case of a safety device, when in position on the power press in connection with which it is to be used. 2) No power press shall be used unless it has been thoroughly examined and tested by a competent person within the immediately preceding period of twelve months. 3) No power press shall be used unless every safety device (other than fixed fencing) thereon has within the immediately preceding period of six months when in position on that power press, been thoroughly examined and tested by a competent person. 4) The competent person carrying out an examination and test under the foregoing provisions shall make a report of the examination and test containing the following particulars and every such report shall be kept readily available for inspection; a) name of the occupier of the factory; b) address of the factory; c) identification number or mark sufficient to identify the power press or the safety device; d) date on which the power press or the safety device was first taken into use in the factory; e) the date of each periodical thorough examination carried out as per requirements of sub-paragraph (2) above; f) Particulars of any defects effecting the safe working of the power press or the safety device found at any such thorough examination and steps taken to remedy such defects. 7. Defects disclosed during a thorough examination and tests. - 52 1) Where any defect is disclosed in any power press or in any safety device by any examination and test under paragraph 6 and in the opinion of the competent person carrying out the examination and test, either - a) the said defect is a cause of danger to workers and in consequence the power press or safety device (as the case may be) ought not to be used after the expiration of a specified period unless the said defect has been remedied; such defect shall, as soon as possible after the completion of the examination and test, be notified in writing by the competent person to the occupier of the factory and, in the case of a defect falling withing clause (1) of this sub-paragraph such notification shall include the period within which, in the opinion of the competent person, the defect ought to be remedied. 2) In every case where notification has been given under this paragraph, a copy of the report made under paragraph 6(4) shall be sent by the competent person to the inspector for the area within 14 (fourteen) days of the completion of the examination and test. 3) Where any such defect is notified to the occupier in accordance with the foregoing provisions of this paragraph the power press or safety device (as the case may be) having the said defect shall not be used – a) in the case of a defect falling within clause (a) of subparagraph (1) until the said defect has been remedied; and b) in the case of defect falling within clause (b) of subparagraph (1), after the expiration of the said defect has been remedied. 4) As soon as is practicable after any defect of which notification has been given under sub-paragraph (1) has been remedied, a record shall be made by or on behalf of the occupier starting the measures by which and the date on which the defect was remedied. 8. Inspection and test of safety device. – 1) No power press shall be used after the setting , resetting or adjustment of the tools thereon unless a person appointed or authorized for the purpose under Paragraph 5 has inspected and tested every safety device thereon while it is in position on the said power press; Provided that an inspection, test and certificate as aforesaid shall not be required where any adjustment of the tools has not caused or resulted in any alteration to or disturbance of any safety device on the power press and if, after the adjustment of the tools, the safety devices remain, in the opinion of such a person as aforesaid, in efficient working order. 2) Every power press and every safety device thereon while it is in position on the said power press shall be inspected any tested by a trained person every day. 9. Defects disclosed during an inspection and test. – 1) Where it appears to any person as a result of any inspection and test carried out by him under paragraph 8 that any necessary safety device is not in position or is not properly in position on a power press or that any safety device which is in position on a power press is not in his opinion suitable, he shall notify the manager forthwith. 2) Except as provided in sub-paragraph (3) where any defect is disclosed in a safety device by any inspection and test under paragraph 8, the person carrying out the inspection and test shall notify the manager forthwith. 3) Where any defect in a safety device is the subject of a notification in writing under paragraph 7 by virtue of which the use of the safety device may be continued during a specified period without the said defect having 53 been remedied, the requirement in sub-paragraph (2) of this paragraph shall not apply to the said defect until the said period has expired. 10. Identification of power presses and safety devices. – For the purpose of identification every power press and every safety device provided for the same shall be distinctively and plainly marked. 11. Training and instructions to operators. – The operators shall be trained and instructed in the safe method of work before starting work on any power press. 12. Exemption. – 1) If in respect of any factory, the Chief Inspector is satisfied that owing to the circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule are not necessary for the protection of the workers employed on any power press or any class or description of power or in the factory, the Chief Inspector may by a certificate in writing (which he may in his discretion revoke at any time), exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. 2) Where such exemption is granted, a legible copy of the certificate, showing the conditions (if any) subject to which it has been granted, shall be kept posted in the factory in a position where it may be conveniently read by the persons employed. Schedule VIII Shears, Slitters and Guillotine Machines 1. Definition. – For the purpose of this schedule – a) “guillotine” means a machine ordinarily equipped with straight, bevel- edged blade operating vertically against a stationery resisting edge and used for cutting metallic or non-metallic substances; b) “shears” or “shearing machine” means a machine ordinarily equipped with straight, bevel-edged blades operating vertically against resisting edges, or with rotary, overlapping cutting wheels, and used for shearing metals or non-metallic substances; c) “slitter” or “slitting machine” means a machine ordinarily equipped with circular disc-type knives, and used for trimming or cutting into metal or non-metallic substances or for slitting them into narrow strips; for the purpose of this schedule, this term includes bread or other food slicers equipped with rotary knives or cutting discs. 2. Guillotine and Sheers. – 1) Where practicable, a barrier metal guard of adequate strength shall be provided at the front of the knife, fastened to the machine frame and shall be so fixed as would prevent any part of the operator’s body to reach the descending blade from above, below or through the barrier guard or from the sides; Provided that in case of machines used in the paper printing and allied industries; where a fixed barrier metal guard is not suitable on account of the height and volume of the material being fed, there shall be provided suitable starting devices which require simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade. 2) At the back end of such machines, an inclined guard shall be provided over which the slit pieces would slide and be collected at a safe 54 distance in a manner as would prevent a person at the back from reaching the descending blade. 1 Power-driven guillotine cutters, except continuous feed trimmers, shall be equipped with – 1 starting devices which require the simultaneous action of both hands to start the cutting motion and of at least one hand on a control during the complete stroke of the knife; or 2 an automatic guard which will remove the hands of the operator from the danger zone at every descent of the blade, used in conjunction with one-hand starting devices which require two distinct movements of the device to start the cutting motion, and so designed as to return positively to the non starting position after each complete cycle of the knife. 2 Where two or more workers are employed at the same time on the same power-driven guillotine cutter equipped with two-hand control the device shall be so arranged that each worker shall be required to use both hands simultaneously on the safely trip to start the cutting motion, and at least one hand on a control to complete the cut. 3 Power-driven guillotine cutters, other than continuous trimmer, shall be provided, in addition to the brake or other stopping mechanism, with an emergency device which will prevent the machine from operating in the event of failure of the brake when the starting mechanism is in the non- starting position. 3. Slitting Machines : 1) Circular disc-type knives on machines for cutting metal and leather paper, rubber, textiles or other non-metallic substances shall, if within reach of operators standing on the floor or working level, if within reach of operators standing on the floor or working level, be provided with guards enclosing the knife edges at all times as near as practicable to the surface of the material, and which may either – a) automatically adjust themselves to the thickness of the material; or b) be fixed or manually adjusted so that the space between the bottom of the guard and the material will not exceed 6mm(0.25”) at any time. 2) Portion of blades underneath the tables or benches of slitting machines shall be covered by guards. 4. Index cutters and Vertical paper Slotters : Index cutters, and other machines for cutting strips from the ends of book, and for similar operations, shall be provided with fixed guards, so arranged that the fingers of the operators can not come between the blades and the tables. 5. Corner Cutters; Corner cutters,. used in the manufacture of paper boxes, shall be equipped with – a) Suitable guard, fastened to the machines in front of the knives and provided with slots or perforations to afford visibility of the operations; or b) other guards equally efficient for the protection of the fingers of the workers. 6. Band knives : Band Wheels on band knives, and all portions of the blades except the table on vertical machines, or between the sliding guide and the table on vertical machines, or between the wheel guards on horizontal machines, shall be completely enclosed with hinged guards of sheet metal not less than 1 mm (0.04″)in thickness or of other material of equal strength. 55 Schedule IX Agitators and Mixing Machines 1. Definition. – “Agitators and Mixing Machines” means a tank or other container equipped with power-driven mixing arms, blades or paddle wheels fixed to revolvable shafts or other simple mechanical devices for blending stirring liquids with other liquids or with solid substances or combinations of these. 2. When the top of an open agitator tank, beater tank, tank or paddle tank or a similar vessel is less than 1 M above the adjacent floor or working level, adequate standard railings shall be installed on all open sides. 3. Agitators and mixing machines shall be provided with an efficient inter-lock arrangement for the top lid, to prevent access to the agitating, stirring or similar devices, whilst in motion and would prevent restart under power with the lids in open position. 4. When other inspection or examination openings are provided at the top or sides of the containers vessels of the agitator and mixing machines, such openings shall be provided with standard grill guards as would prevent access of any part of operator’s body coming in contact with agitating, stirring or similar devices, whilst in motion inside the vessel. Schedule X Leather, Plastic and Rubber Stripper Machines Strippers for trimming or punching tanned hides, plastic or rubber sheets in leather making footwear manufacturing or in similar industries shall be provided with suitable devices which require simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade, punch or stripper cutter. Schedule XI 1. Special Rule for printing presses. In printing works, every printing machine driven by power shall be fitted with an efficient finger guard and every guillotine machine, driven by power, with an efficient knife-guard. 2. Special rule for tea factories. In tea factories, the roll table shall be fenced to the satisfaction of the Inspector and brushes shall be provided to the workers for the purposes of sweeping the roll table. 3. Special rule for bricks and tiles works. In brick and tiles works, a finger-guard shall be fitted at the feed end to the full length of the mould of every revolving press. 4. Special rule for decorticating factories. In decorticating factories, the beater arms and the feed mouth of the decorticator shall, as far as practicable, be guarded as follows:- A grating of 19 millimeters diameter wrought iron rods spaced 64 millimeters apart and supported by iron stiffeners 5.1 centimeters by 6 millimeters thick shall be fixed at a height of 15.2 centimeters above to the tip of the beater arms. A strong wooden plank 38 millimeters thick and iron plated on the underside shall be clamped with bolts and nuts over this grating, leaving a space of 20.3 centimeters wide for the feeding of groundnuts. A grating of 2.5 centimeters diameter wraught iron rods spaced 38 millimeters apart shall be fixed at a height 56 of 12.7 centimeters just above the feed mouth and another wooden plank 22.9 centimeters wide shall be fixed over the full length of the decorticator platform. 5. Special rules for factories in which polishing and grinding machinery are in use. Safety devices:- a) All collars, set screws, shafts, couplings, clutches, keys and belts in polishing and grinding machinery shall be effectively guarded. b) i) Defect wheels shall not be used. ii) Grinding wheels shall fit freely on their spindles. They shall never be forced on, nor shall they be let loose on spindles. iii) The soft metal bushings at the centre shall not extend beyond the sides of the wheels. iv) Whenever possible, a compressible medium, such as blotting paper, rubber or similar material, at least as large in diameter as that of the flanges, shall be fitted between a wheel and each of its flanges. v) Projecting arbor ends of grinding and polishing wheels shall effectively guarded. c) Except with the written permission of the Chief Inspector no emery or abrasive wheel shall be kept unprovided with a strong iron cover guard that shall enclose the wheel as far as practicable to retain fragments in the event of bursting. The guard shall be securely attached to the frame of the machine or other solid foundation. d) Where workers are employed continuously on dry grinding or polishing wheels, such wheels shall be provided with an efficient exhaust system capable of drawing off dust particles. e) Wheels shall not be operated at a speed in excess of that which is recommended by the manufacturer. Schedule XII All factories a) Wherever practicable and considered necessary by the Inspector, service platforms and gangways shall be provided for overhead shafting and where required by him these shall be securely fenced with guards, rails and toe boards. b) Safe access shall be provided to all bearing clutches, belt shifting levers and all such other appliances which are required to be handled or operated while the machinery is at work. c) All ladders used in replacing belts or in attending similar overhead machinery shall be specially made for that work and provided with hooks or an effective non- skid device. d) No transmission machinery in motion shall be cleaned with cotton waste rags or similar materials held in hand. e) All belts shall be regularly examined to ensure that the joints are safe and the belts are kept in proper tension. f) Each water gauge glass of a boiler shall be fitted with an efficient guard. g) All condenser pipes of steam engines and exhaust pipes of oil engines shall be adequately guarded. Rule 68. Register of workers employed for work on or near machinery in motion:- In every factory a register shall be maintained in Form 12 in which the name and other particulars of every such worker as may be employed for such examination or operation as referred to in the proviso to sub-section (1) of section 21 shall be entered. 57 Rule 69. Tight fitting clothing – A worker required to wear tight fitting clothing under subsection (1) of section 22 shall be provided by the occupier with such clothing which shall consist of at least a pair of closely fitting shorts and a closely fitting half sleeves shirt or vest. Such clothing shall be returned to the occupier on termination of service or when new clothing is provided. Rule 70. All Belts Etc. To Be Examined Regularly: All belts shall be regularly examined to ensure that the joints are safe and the belts are at proper tension. The manager of the factory shall maintained a record of such examination indicating the date of examination and the person by whom examined and his opinion. This register shall be produced before the Inspector when he wants. Rule 71. Employment of young persons on dangerous machines: a) Power presses other than hydraulic presses. b) Milling machines used in the metal trades. c) Shears slitters and Guillotine machines. d) Wood working machines. e) Decorticator machines. f) Platen printing machines. g) Centrifugal machines. Rule 72. Hoists and Lifts:- 1. A register in Form 13 shall be maintained by the manager to record the particulars of examination of hoists and lifts of a factory. 2. Examination of certain hoists and lifts:- In pursuance of the provisions of sub-section (4) of section 28, in respect of any clase or description of hoist or lift specified in the first column of the following schedule, the requirements of section 28 specified in the second column of the said schedule and set opposite to that class or description of hoist or lift shall not apply. SCHEDULE Class or Description of Hoist or Lift Requirement which shall not apply Hoists or Lifts, mainly used for raising Sub-Sec 1(b) in so far as it requires a materials for charging blast furnace or gate at the bottom landing; Sub-Sec lime kilns. 1(d); Sub-Sec 1(e). Hoists not connected with mechanical Sub-Sec 1(b) in so far as it requires the power and which are not used for hoistway or liftway enclosures to be so carrying persons. constructed as to prevent any person or thing from being trapped between any part of the hoist or lift and any fixed structure or moving part; Sub-Sec 1(e). Rule 73. Lifting machines, chains, ropes and lifting tackles:- 1. No lifting machine and no chain, rope or lifting tackle, except a fibre rope or fibre rope sling, shall be taken into use in any factory for the first time in that factory 58 unless it has been tested and all parts have been thoroughly examined by a competent person and a certificate of such a test and examination specifying the safe working load or loads and signed by the person making the test and the examination, has been obtained and is kept available for inspection. 2. Every jib-crane so constructed that the safe working load may be varied by the raising or lowering of the jib, shall have attached thereto either an automatic indicator of safe working loads or an automatic jib angle indicator and a table indicating the safe working loads at corresponding inclinations of the jib or corresponding radii of the road. 3. A table showing the safe working loads of every kind and size of chain, rope or lifting tackle in use, and, in the case of a multiple sling, the safe working loads at different angles of the legs, shall be posted in the store room or place, where or in which the chains, ropes or lifting tackles are kept, and in prominent positions on the promises, and no chain, rope or lifting tackle not shown in the table shall be used: Provided that this sub-rule shall not apply in respect of such lifting tackle of the safe working load thereof, or in the case of a multiple sling, the safe working load at different angles of the legs, is plainly marked upon it. 5. All rails on which a traveling crane moves and every tract on which the carriage of a transporter or runway moves shall be of proper size and adequate strength and have an even running surface; and every such rail or track shall be properly laid, adequately supported and properly maintained. 6. To provide access to rail tracks of overhead traveling cranes suitable passage- ways of at least 50 centimeters width with two boards and double hand rails 90 centimeters high shall be provided alongside, and clear of, the rail tracks of overhead traveling cranes, such that no moving part of the crane can strike persons on the ways, and the passage-way shall be at a lower level than the crane track itself. Safe access ladders shall be provided at suitable intervals to afford access to these passage-ways, and from passage-ways to the rail tracks. Provided that the Chief Inspector may, for reasons to be specified in writing, exempt any factory in respect of any overhead traveling crane from the operation of any provision of this sub-rule subject to such conditions as he may specify. 7. All chains and lifting tackles except a rope sling shall, unless they have been subjected to such other heat treatment as may be approved by the Chief Inspector, be effectively annealed under the supervision of a competent person at the following intervals: a) all chains, slings, rings, hooks, shackles and swivels used in connection with molten metal or molten slag or when they are made of 12.5 millimeters bar or smaller, once at least in every six months; b) all other chains, slings, rings, hooks, shackles and swivels in general use, once at least in every twelve months: Provided that chains and lifting tackle not in frequent use shall, subject to the Chief Inspector’s approval, be annealed only when necessary. Particulars of such annealing shall be entered in a register prescribed under sub-rule (4) which shall be kept available for inspection. 8. Nothing in the foregoing sub-rule (7) shall apply to the following classes of chains and lifting tackles: a) chains made of malleable cast iron; b) plate link chains; c) chains, rings, hooks, shackles and swivels made of steel or of any non- ferrous metal; d) pitched chains, working on sprocket or pocketed wheels; 59 e) rings, hooks, shackles and swivels permanently attached to pitched chains, pulley, blocks or weighing machines; f) hooks and swivels having screw threaded parts or ball bearing or other case hardened parts; g) socket shackles secured to wire ropes by white-metal capping; and h) bordeaux connections; i) any chain or lifting tackle which has been subjected to the heat treatment known as “Normalizing” instead of annealing. Provided that such chains and lifting tackles shall be thoroughly examined by a competent person once atleast in every twelve months, and particulars entered in the register kept in accordance with sub rule (4). 9. No person under 18 years of age and no person who is not sufficiently competent and reliable shall be employed as driver of a lifting machine whether driven by mechanical power or otherwise, or to give signals to a driver. 10. All lifting machines, chains, ropes and lifting tackle except a fibre rope or fibre rope sling, which have been lengthened, altered or repaired by welding or otherwise shall, before being again taken into use, be adequately re-tested and re- examined by a competent person and a certificate of such test and examination be obtained and particulars entered in the register kept in accordance with sub-rule (4). 11. Where the Chief Inspector is satisfied that in a factory due to shut down or for any other persons it is not practicable to maintain a minimum distance of 6 meters between the person employed or working on or near the wheel track of a traveling crane and the crane, he may on the request of the manager reduce the distance to such extent as he may consider necessary and also prescribe further precautions indicating appointment of suitable number of supervisors to ensure the safety of the persons while they ;are employed or working on or near the track. Rule 74. Pressure vessels or plant: 1. Interpretation. – In this rule – a) “pressure vessel” means a vessel that may be used for containing, storing, distributing, transferring, distilling processing or otherwise handling any gas, vapour or liquid under pressure greater than the atmospheric pressure and includes any pipeline fitting or other equipment attached thereto or used in connection therewith; and b) “design pressure” means the maximum pressure that a pressure vessel or plant is designed to withstand safely when operating normally; c) “maximum permissible working pressure” means the maximum pressure at which a pressure vessel or plant is permitted to be operated or used under this rule and is determined by the technical requirement of the process; d) “plant” means a system of piping that is connected to a pressure vessel and is used to contain a gas vapour or liquid under pressure greater than the atmospheric pressure, and includes the pressure vessel; e) “competent person” means a person who is, in the opinion of the Chief Inspector, capable by virtue of his qualification, training and experience, of conducting a thorough examination and pressure tests, as required on a pressure vessel or plant, and of making a full report on its condition. 2. Exceptions. – Nothing in this rule shall apply to – a) vessels made of ferrous materials having an internal operating pressure not exceeding 1 kg per Square cm; 60 b) steam boilers, steam and feed pipes and their fittings coming under the purview of Indian Boilers Act, 1923; c) metal bottles or cylinders used for storage or transport of compressed gases or liquefied or dissolved gases under pressure covered by the Gas Cylinder Rules, 1981 framed under the Indian Explosives Act, 1884; d) vessels in which internal pressure is due solely to the static head of liquid; e) vessels with a nominal water capacity not exceeding 500 litres connected in a water-pumping system containing air that is compressed to serve as a cushion; f) vessels for nuclear energy application; g) refrigeration plant having a capacity of 3 tons or less or refrigeration in 24 hours; and h) working cylinders of steam engines or prime movers, feed pumps and steam traps; turbine casings; compressor cylinders; steam separators or dryers; steam strainers; steam de-super-heaters; oil separators; air receivers for fire sprinkler installations; air receivers of monotype machines provided the maximum working pressure of the air receiver does not exceed 1.33 kilograms per square centimeter and the capacity 85 litres; air receivers of electrical circuit breakers; air receivers of electrical relays; air vessels on pumps pipe coils, accessories of instruments and appliances such as cylinders and piston assemblies used for operating relays and interlocking type of guards; vessels with liquids subjected to static head only; and hydraulically operating cylinders other than any cylinder communicating with an air loaded accumulator. 3. Design and construction. – Every pressure vessel or plant used in a factory- a) shall be properly designed on sound engineering practice; b) shall be of good construction, sound material, adequate strength and free from any patent defects; c) shall be properly maintained in a safe condition; Provided that the pressure vessel or plant in respect of the design ;and construction of which there is an Indian standard or a standard of the country of manufacture or any other low or regulation in force, shall be designed and constructed in accordance with the said standard law or regulation, as the case may be and a certificate thereof shall be obtained from the manufacturer or from the competent person which shall be kept and produced on demand by an Inspector. 4. Safety devices. – Every pressure vessel shall be fitted with. a) a suitable safety valve or other effective pressure relieving device of adequate capacity to ensure that the maximum permissible working pressure of the pressure vessel shall not be exceeded. It shall be set to operate at a pressure not exceeding the maximum permissible working pressure and when more than one protective device is provided, only one of the devices need be set to operate at the maximum permissible working pressure and the additional device shall be set to discharge at a pressure not more than 5 percent in excess of the maximum permissible working pressure; b) a suitable pressure gauge with a dial range not less than 1.5 times the maximum permissible working pressure easily visible and designed to show at all times the correct internal pressure and marked with a prominent red mark at the maximum permissible working pressure of the pressure vessel; 61 c) a suitable nipple and globe valve connected for the exclusive purpose of attaching a test pressure guage for checking the accuracy of the pressure guage referred to in clause (b) of this sub-rule; d) a suitable stop valve or valves by which the pressure vessel may be isolated from other pressure vessels or plant or source of supply of pressure. Such a stop valve or valves shall be located as close to the pressure vessel as possible and shall be easily accessible; and e) a suitable drain cock or valve at the lowest part of the pressure vessel for the discharge of the liquid or other substances that may collect in the pressure vessel; Provided that it shall be sufficient for the purpose of this sub-rule if the safety valve or pressure relieving device, the pressure guage and the stop valve are mounted on a pipeline immediately adjacent to the pressure vessel and where there is a range of two or more similar pressure vessels served by the same pressure lead, only one set of such mountings need be fitted on the pressure lead immediately adjacent to the range of pressure vessels, provided they cannot be isolated. 5. Pressure reducing devices: a) Every pressure vessel which is designed for a working pressure less than the pressure at the source of supply or less than the pressure which can be obtained in the pipe connection the pressure vessel with any other source of supply, shall be fitted with a suitable pressure reducing valve or other suitable automatic device to prevent the maximum permissible working pressure of the pressure vessel being exceeded. b) To further protect the pressure vessel in the event of failure of the reducing valve or device, at least one safety valve having a capacity sufficient to release all the steam, vapour or gas without undue pressure rise as determined by the pressure at the source of supply and the size of the pipe connecting the source of supply, shall be fitted on the low pressure side of the reducing valve. 6. Pressure vessel or plant being taken into use: a) No new pressure vessel or plant shall be taken into force of this rule unless it has been hydrostatically tested by a competent person at a pressure at least 1.3 times the design pressure, and no pressure vessel or plant which has been previously used or has remined isolated of idle for a period exceeding 2 months or which has undergone alterations or repairs shall be taken into use in a factory unless it has been thoroughly examined by a competent person externally and internally, if practicable, and has been hydrostatically tested by the competent person at a pressure which shall be 1.5 times the maximum permissible working pressure ; Provided, however, that the pressure vessel or plant which is so designed and constructed that it cannot be safely filled with water or liquid or is used in service when even some traces of water cannot be tolerated, shall be pneumatically tested at a pressure not less than the design pressure or the maximum permissible working pressure as the case may be. Provided further that the pressure vessel or plant which is lined with glass shall be tested hydrostatically or pneumatically as required at a pressure not less than the design pressure or maximum permissible working pressure as the case may be. Design pressure shall be not less than the maximum permissible working pressure and shall take into account the possible fluctuations of pressure during actual operation. 62 b) No pressure vessel or plant shall be used in a factory unless there has been obtained from the maker of the pressure vessel or plant or froms the competent person a certificate specifying the design pressure or maximum permissible working pressure thereof, and stating the nature of tests to which the pressure vessel or plant and its fittings (if any) have been subjected, and every pressure vessel or plant so used in a factory shall be marked so as to enable it to be identified as to be the pressure vessel or plant to which the certificate relates and the certificate shall be kept available for perusal by the Inspector. c) No pressure vessel or plant shall be permitted to be operated or used at a pressure higher than its design pressure, or the maximum permissible working pressure as shown in the certificate. 7. In-service test and examinations: a) Every pressure vessel or plant in service shall be thoroughly examined by a competent person- i) Externally, once in every period of six months; ii) Internally, once in every period of twelve months; Provided that if by reason of the construction of a pressure vessel or plant, a thorough internal examination is not possible, this examination may by replaced by a hydrostatic test which shall be carried out once in every period of two years. Provided further that for a pressure vessel or plant in continuous process which cannot be frequently opened, the period of internal examination may be extended to four years; and iii) hydrostatically tested once in every period of four years. Provided that in respect of a pressure vessel or plant with thin walls, such as sizing cylinder made of copper or any other nonferrous metal, periodic hydrostatic test may be dispensed with subject to the condition that the requirements laid down in sub-rule (8) are fulfilled. Provided further that when it is impracticable to carry out thorough external examination of any pressure vessel or plant every six months as required in sub-clause (i) of this clause, or if owing to its construction and use a pressure vessel or plant cannot be hydrostatically tested as required in sub-clause (ii) and (iii) of this clause, a thorough external examination of the pressure vessel or plant shall be carried out at least once in every period of two years, and at least once in every period of four years, a thorough systematic non-destructive test like ultrasonic test for metal thickness or other defects of all parts the failure of which might lead to eventual rupture of the pressure vessel or plant shall be carried out. b) The pressure for the hydrostatic test to be carried out for the purpose of this sub-rule shall be 1.25 times the design pressure or 1.5 times the maximum permissible working pressure, whichever is less. 8. Thin walled pressure vessel or plant. – a) In respect of any pressure vessel or plant of thin walls such as sizing cylinder made of copper or any other non-ferrous metal, the maximum permissible working pressure shall be reduced at the rate of 5 percent of the original maximum permissible working pressure for every year of its use after the first five years and no such cylinder shall be allowed to continue to be used for more than twenty years after it was first taken into use. 63 b) If any information as to the date of construction, thickness of walls, or maximum permissible working pressure is not available, the age of such pressure vessel or plant shall be determined by the competent person in consultation with the Chief Inspector from the other particulars available with the manager. c) Every new and second hand pressure vessel or plant of thin walls to which repairs likely to affect its strength or safety have been carried out, shall be tested before use to at least 1.5 times its maximum permissible working pressure. 9. Report by competent person. – a) If during any examination any doubt arises as to the ability of the pressure vessel or plant to work safely until the next prescribed examination, the competent person shall enter in the prescribed register his observations, findings and conclusions with other relevant remarks with reasons and may authorize the pressure vessel or plant to be used and kept in operation subject to a lowering of maximum permissible working pressure, or to more frequent or special examination or test, or subject to both of these conditions. b) A report of every examination or test carried out shall be completed in Form 15 and shall be signed by the person making the examination or test, and shall be kept available for perusal by the Inspector at all hours when the factory or any part thereof is working. c) Where the report of any examination under this rule specified any condition for securing the safe working of any pressure vessel or plant, the pressure vessel or plant shall not be used unless the specified condition is fulfilled. d) The competent person making report of any examination under this rule, shall within seven days of the completion of the examination, send to the Inspector a copy of the report in every case where the maximum permissible working pressure is reduced or the examination shows that the pressure vessel or plant or any part thereof cannot continue to be used with safety unless certain repairs are carried out or unless any other safety measure is taken. 10. Application of other laws. – a) The requirements of this rule shall be in addition to and without any prejudice to and not in derogation of the requirements of any other law in force. b) Certificate or reports of any examination, or test of any pressure vessel or plant to which sub-rules (7) to (9) do not apply, conducted or required to be conducted under any other law in force and other relevant record relating to such pressure vessel or plant, shall be properly maintained as required under the said law and shall be produced on demand by the Inspector. Rule 75. Water-sealed gasholder: 1. The expression “gasholder” means a water-sealed gasholder which has a storage capacity of not less than 141.5 cubic meters. 2. Every gasholder shall be of adequate material and strength, sound construction and properly maintained. 64 3. Where there is more than one gasholder in a factory, every gasholder shall be marked in a conspicuous position with a distinguishing number or letter. 4. Every gasholder shall be thoroughly examined externally by a competent person at least once in a period of 12 months. 5. In the case of gasholder of which any lift has been in use for more than 10 years, the internal state of the sheeting shall, within one year of the coming into operation of these rules and thereafter at least once in every period of four years, be examined by a competent person by means of electronic or other accurate devices. Provided that if the Chief Inspector is satisfied that such electronic or other accurate devices are not available, he may permit the cutting of samples from the crown and the sides of the holder. Provided further that if the above examination raises a doubt, an internal visual examination shall be made. 6. All possible steps shall be taken to prevent or minimize ingress of impurities in the gasholder. 7. No gasholder shall be repaired or demolished except under the direct supervision of a person who, by his training experience and knowledge of the necessary precautions against risks of explosion and of persons being overcome by gas, is competent to supervise such work. 8. a) All sample discs cut under sub-rule (5) above shall be kept readily available for inspection. b) A permanent register in Form 16 duly signed by the occupier or manager shall be maintained. c) The result of examinations by the competent person carried out as required under sub-rules (4) and (5) shall be recorded in Form 17. d) A copy of the report in Form 17 shall be kept in the register in Form 16 and both the register and the report shall be readily available for inspection. 9. The Inspector shall inspect the gasholder at least once in a period of 12 months. Rule 76. Excessive weights:- 1. No man, woman, or young person shall unaided by another person, lift, carry or move by hand or on head any material article, tool or appliance exceeding the maximum limit in weight set out in the following schedule. SCHEDULE Persons. Maximum weight of material, article, tool or appliance. a) Adult male 50 kg. b) Adult female 25 kg. c) Adolescent male 20 kg. d) Adolescent female 20 kg. e) Male child 15 kg. f) Female child 10 kg. 2. No man, Women young person shall engage, in conjunction with others, in lifting, carrying or moving by hand or on head any material article, tool or appliance, if the weight thereof exceeds the lowest weight fixed by the Schedule to sub-rule(1) for any of the persons engaged, multiplied by the number of the persons engaged. 65 Rule 77. Protection of eyes:- Effective screens or suitable goggles shall be provided for the protection of persons employed in or in the immediate vicinity of the following processes:- a) The processes specified in schedule I annexed hereto, being processes which involve risk of injury to eyes from particles or fragments thrown of in the course of the processes. b) The processes specified in Schedule II annexed hereto, being processes which involve risk of injury to eyes by reason of exposure to excessive light or infra-red or ultraviolet radiations. Schedule I 1. Breaking, cutting, dressing or carrying of bricks, stone, concrete, slag or similar materials by means of a hammer, chisel, pick or similar hand tool, or by means of a portable tool driven by mechanical power, and the dry grinding of surfaces of any such materials by means of a wheel or disc driven by mechanical power, where, in any of the foregoing causes, particles or fragments are liable to be thrown off towards the face of the operator in the course of the process. 2. Dry grinding of surfaces of metal by applying them by hand to a wheel, disc or band driven by mechanical power, and of surfaces of metal by means of a portable tool driven by mechanical power. 3. Dividing into separate parts of metal, bricks, stone, concrete or similar materials by means of a high speed saw driven by mechanical power or by means of an abrasive cutting-off wheel or disc driven by mechanical power, where particles or fragments are liable to be thrown off towards the face of the operator in the course of process. 4. Turning of metals or articles of metal, where particles or fragments are liable to be thrown off towards the face of the operator in the course of the process. 5. Drilling by means of portable tools, where particles or fragments are liable to be thrown off towards the face of the operator in the course of the process. 6. Welding and cutting of metals by means of an electric, oxy-acetylene or similar process. 7. Hot fettling of steel castings by means of a flux-injected burner or air torch, and de-seaming of metal. 8. Fettling of metal castings involving the removal of metal, including runners, gates and risers, and removal of any other material during the course of such fettling. 9. Chipping of metal, and chipping, knocking out, cutting out or cutting off of cold rivets, bolts, nuts, lugs, pins, collars or similar articles from any structure or plant, or from part of any structure or plant, by means of a hammer, chisel, punch or similar hand tool, or by means of a portable tool driven by mechanical power. 10. Chipping or scurffing of paint, scale, slag, rust or other corrosion from the surface of metal and other hard materials by means of a hand tool or by a portable tool driven by mechanical power. 11. Breaking of scrap metal by means of a hammer or by means of a tool driven by mechanical power. 12. Routing of metal, where particles or fragments are liable to be thrown off towards the face of the operator in the course of the process. 13. Work with drop hammers and power hammers used in either case for the manufacture of forgings, and work by any person not working with such 66 hammers, whose work is carried on in such circumstances and in such a position that particles or fragments are liable to be thrown off towards his face during work with drop hammers or power hammers. 14. Work at a furnace where there is risk to the eyes from molten metal. 15. Pouring or skimming of molten metal. 16. Work involving risk to the eyes from hot sand being thrown off. 17. Turning or dressing of an abrasive wheel. 18. Handling in open vessels or manipulation of strong acids or dangerous corrosive liquids or materials, and operation, maintenance or dismantling of plant or any part of plant, being plant or part of plant which contains or has contained such acids, liquids or materials, unless the plant or part of plant has been so prepared (by isolation reduction of pressure, or otherwise), treated, or designed and constructed as to prevent risk of injury. 19. Any other process wherein there is a risk of injury to eyes from particles or fragments thrown off during the course of the process. Schedule II 1. Welding or cutting of metals by means of an electrical, oxy-acetylene or similar process. 2. All work on furnaces where there is risk of exposure to excessive light or infra-red radiations. 3. Process such as rolling, casting or forging of metals, where there is risk of exposure to excessive light or infra-red radiations. 4. Any other process wherein there is a risk of injury to eyes from exposure to excessive light or infra-red or ultraviolet radiations. Rule 78. Minimum dimensions of man-holes:- In any factory no person shall be allowed or required to enter in any chamber, tank, vat, pipe flue or other confined space, which persons may have to enter unless the said chamber, tank, vat, pope flue or other confined space, is provided with a man-hole which may be rectangular, oval or circular in shape unless there is other effective means of egress and - a) in the case of rectangular or oval shape, be not less than shoulder width of the person concerned plus 8 cm. in length and 30 cm. wide; b) in the case of a circular shape be not less than shoulder width of the person concerned plus 8 cm. in diameter. Exemption under sub-section (5) of section (37) Rule 79. Exemptions. The requirements of sub-section (4) of section 37 shall not apply to the following processes carried on in any Factory:- a) The operation of repairing a water-sealed gas-holder by the electric welding process, subject to the following conditions:- i) The gas-holder shall contain only the following gases, separately or mixed at a pressure greater than atmospheric pressure, namely, town gas, coke- oven gas, producer gas, blast furnace gas, or gases, other then air, used in their manufacture: Provided that, this exemption shall not apply to any gasholder containing acetylene or mixture of gases, to which acetylene has been added intentionally; and 67 ii) Welding shall be done by the electric welding process and shall be carried out by experienced operatives under the constant supervision of a competent person. b) The operations of cutting or welding steel or wrought iron gas mains and services by the application of heat, subject to the following conditions: i) The main or service shall be situated in the open air, and it shall contain only the following gases, separately or mixed at a pressure greater than atmospheric pressure, namely, town gas, coke-oven gas, producer gas, producer gas, blast furnace gas, or gases other than air, used in their manufacture. ii) The main or service shall not contain acetylene or any gas or mixture of gases to which acetylene has been added intentionally; iii) The operation shall be carried out by an experienced person or persons and at least two persons (including those carrying out the operations) experienced in work on gas mains and over 18 years of age shall be present during the operation; iv) The site of the operation shall be free from any inflammable or explosive gas or vapour; v) Where acetylene gas is used as a source of heat in connection with an operation, it shall be compressed and contained in a porous substance in a cylinder; and vi) Prior to the application of any flame to the gas main or service, this shall be pierced or drilled and the escaping gas ignited. c) The operation of repairing an oil tank on any ship by the electric welding process, subject to the following conditions:- i) The only oil, contained in the tank shall have a flash point of not less than 150 of (close test) and a certificate to this effect shall be obtained from 2 competent analysts; ii) The analyst’s certificate shall be kept available for inspection by an Inspector, or by any person employed or working on the ship; iii) The Welding operation shall be carried out only on the exterior surface of the tank at a place (a) which is free from oil or oil leakage in inflammable quantities and (b) which is not less than 30 centimeters below the nearest part of the surface of the oil within the tank; and iv) Welding shall be done only by the electric welding and shall be carried out by experienced operatives under the constant supervision of a competent person. Rule 80. Fire protection - 1) Processes, equipment, plant, involving serious explosion and serious fire hazards:- a) All processes, storages, equipments, plants, etc. involving serious explosion and flash fire hazard shall be located in segregated buildings where the equipment shall be so arranged that only a minimum number of employees are exposed to such hazards at any one time. b) All industrial processes involving serious fire hazard should be located in buildings or work places separated from one another by walls of fire- resistant construction. c) Equipment and plant involving serious fire or flash fire hazard shall, wherever possible be so constructed and installed that in case of fire, they can be easily isolated. 68 d) Ventilation ducts, pneumatic conveyors and similar equipment involving a serious fire risk should be provided with flame arresting or automatic fire extinguishing appliance of fire resisting dampers electrically interlocked with heat sensitive/smoke detectors and the air-conditioning plant system. e) In all workplaces having serious fire or flash fire hazard, passages between machines, installations or piles of material should be at least 90 cm. wide. For storage pile the clearance between the ceiling and Top of the pile should not be less than 2 meter. 2) Access for fire fighting:- a) Buildings and plants shall be so laid out and roads, passageways etc. so maintained as to permit unobstructed access for fire fighting. b) Doors, and window openings shall be located in suitable positions on all external walls of the building to provide easy access to the entire area within the building for fire fighting. 3) Protection against lightning:- protection from lightning shall be provided for:- a) building in which explosive or highly flammable substance are manufactured, used handle or stored. b) storage tanks containing oils, paints, or other flammable liquids. c) grain elevation; d) buildings, tall chimneys or stacks where flammable gases, fumes, dust, or lint are likely to be present; e) sub-station buildings and out door transformers and switch yards. 4) Explosive : All explosive shall be handled, transported, stored and used in accordance with the provisions of the Indian Explosive Act, 1884 (4 of 1894). 5) Precautions against ignition. - Wherever there is danger of fire or explosion from accumulation of flammable of explosive substances in air - a) all electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition; b) effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent; c) workers shall wear shoes without iron or steel nails or any other exposed ferrous materials which is likely to cause sparks by friction; d) smoking, lighting or carrying of matches, lighters or smoking materials shall be prohibited. e) transmission belts with iron fasteners shall not be used; and f) all other precautions, as are reasonably practicable, shall be taken to prevent initiation of ignition from all other possible sources such as open flames, frictional sparks, overheated surfaces of machinery or plant, chemical or physical-chemical reaction and radiant heat. 6) Spontaneous ignition:- Where materials are likely to induce spontaneous ignition, care shall be taken to avoid formation of air pocket and to ensure adequate ventilation. The material susceptible to spontaneous ignition should be stored in dry condition and should be in heaps of such capacity and separated by such passage which will prevent fire. The materials susceptible to ignition and stored in the open shall be at a distance not less than 10 meters away from process or storage buildings. 7) Cylinders containing compressed gas:- Cylinders containing compressed gas may only be stored in open if they are protected against excessive variation of temperature, direct rays of sun, or continuous dampness. Such cylinders shall never be stored near highly flammable substances, furnaces or hot processes. The room where such cylinders are stored shall have adequate ventilation. 69 8) Storage of flammable liquids:- a) The quantity of flammable liquids in any work room shall be the minimum required for the process or processes carried on in such room. Flammable liquids shall be stored in suitable containers with close fitting covers: provided that not more than 20 litres of flammable liquids having a flash point of 210C or less shall be kept or stored in any work room. b) Flammable liquids shall be stored in closed containers and in limited quantities in well ventilated rooms of fire resisting construction which are isolated from the remainder of the building by fire walls and self closing fire doors. c) Large quantities of such liquids shall be stored in isolated adequately ventilated building of fire resisting construction or in storage tanks, preferably underground and at a distance from any building as required in the Petroleum Rules,1976. d) Effective steps shall be taken to prevent leakage of such liquids into basements, sumps or drains and to confine any escaping liquid within safe limits. 9) Accumulation of flammable dust, gas, fume or vapour in air or flammable waste material on the floors:- a) Effective steps shall be taken for removal or prevention of the accumulation in the air of flammable dust, gas, fume or vapour to an extent which is likely to be dangerous. b) No waste material of a flammable nature shall be permitted to accumulate on the floors and shall be removed at least once in a day or shift, and more often, when possible. Such materials shall be placed in suitable metal containers with covers wherever possible. 10) Fire exits:- a) In this rule:- i) “horizontal” exits” means an arrangement which allows alternative egress from a floor area to another floor at or near the same level in an adjoining building or an adjoining part of the same building with adequate separation and ii) “travel distance” means the distance an occupant has to travel to reach an exit. b) An exit may be doorway, corridor, passageway to an external stairway or to a verandah or to an internal stairway segregated from the rest of building by fire resisting walls which shall provide continuous and protected means or egress to the exterior of a building or to an exterior open space. An exit may also include a horizontal exit leading to an adjoining building at the same level. c) Lifts, escalators and revolving doors shall not be considered as exits for the purpose of this sub-rule. d) In every room of a factory exits sufficient to permit safe escape of the occupants in case of fire or other emergency shall be provided which shall be free of any obstruction. e) The exits shall be clearly visible and suitably illuminated with suitable arrangement, whatever artificial lighting is to be adopted for this purpose, to maintain the required illumination in case of failure of the normal source of electric supply. f) The exits shall be marked in a language understood by the majority of the workers. g) Iron rung ladders or spiral staircases shall not be used as exit staircases. 70 h) Fire resisting doors or roller shutters shall be provided at appropriate places along the escape routes to prevent spread of fire and smoke, particularly at the entrance of lifts or stair where funnel or flue effect may be cleared inducing an upward spread of fire. i) All exits shall provide continuous means of egress to the exterior of a building or to an exterior open space leading to a street. j) Exits shall be so located that the travel distance to reach at least one of them on the floor shall not exceed 30 meters. k) In case of those factories where high hazard materials are stored or used, the travel distance to the exit shall not exceed 22.5 metres and there shall be at least two ways of escape from every room, however small, except toilet rooms, so located that the points of access thereto are out of or suitable shielded from areas of high hazard. l) Whenever more than one exit is required for any room space of floor, exits shall be placed as remote from each other as possible and shall be arranged to provide direct access in separate directions from any point in the area served. m) The unit of exit width used to measure capacity of any exit shall be 50 cm. A clear width of 25 cm. shall be counted as an additional half unit. Clear width of less than 25 cm. shall not be counted for exit width. n) Occupants per unit width shall be 50 for stairs and 75 for doors. o) For determining the exits required, the occupant load shall be reckoned on the basis of actual number of occupants within any floor area or 10 square metres per person, whichever is more. p) There shall not be less than two exits serving every floor area above and below the ground floor, and at least one of them shall be an internal enclosed stairway. q) For every building or structure used for storage only, and every section thereof considered separately, shall have access to at least one exit so arranged and located as to provide a suitable means of escape for any persons may be normally present, at least two separate means of exit shall employ therein and in any such room wherein more than 10 persons be available, as remote from each other as practicable. r) Every storage area shall have access to at least one means of exit which can be readily opened. s) Every exit doorway shall open into an enclosed stairway, a horizontal exit on a corridor or passageway providing continuous and protected means of egress. t) No exit doorway shall be less than 100 cm in width, Doorways shall be not less than 200 cm, in height. u) Exit doorways shall open outwards, that is, away from the room but shall not obstruct the travel along any exit. No door when opened, shall reduce the required width of stairway or landing to less that 90 cm. Over head or sliding doors shall not be installed for this purpose. v) An exit door shall not open immediately upon a flight of stairs. A landing at least 1.5m ×1.5m in size shall be provided in the stairway at each doorway. The level of landing shall be the same as that of the floor which it serves. w) The exit doorways shall be open able from the side which they serve without the use of a key. x) Exit, corridors and passageways shall be of a width not less than the aggregate required width of exit doorways leading the side. 71 y) Where stairways discharge through corridors and passageways, the height of the corridors and passageways shall not be less than 2.4 metres. aa) Internal stairs shall be constructed of non-combustible materials throughout. bb) Internal stairs shall be constructed as a self-contained unit with at least one side adjacent to external wall and shall be completely enclosed. cc) A stair case shall not be arranged round a lift shaft unless the latter is totally enclosed by a material having a fire resistance rating not lower than that of the type of construction of the former. dd) Hollow combustible construction shall not be permitted. ee) The minimum width of an internal staircase shall be 100 cm. ff) The minimum width of treads without nosing shall be 25 cm, for an internal staircase. The Treads shall be constructed and maintained in a manner to prevent slipping. gg) The maximum height of a riser shall be 19 cm, and the number of risers shall be limited to 12 per flight. hh) Hand rails shall be provided with a minimum height of 100 cm. and shall be firmly supported. ii) To use of spiral staircase shall be limited to low occupant load and to building of height of 9 metres, unless they are connected to platforms such as balconies and terraces to allow escapees to pause. A spiral staircase shall be not less than 300 cm. in diameter and have adequate head room. jj) The width of a horizontal exit shall be same as for the exit doorways. kk) The horizontal exit shall be equipped with at least one fire door of self closing type. ll) The floor area on the opposite or refuge side of a horizontal exit shall be sufficient to accommodate occupants of the floor areas served allowing not less than 0.3 square metre per person. The refuge area shall be provided with exits adequate to meet the requirements of this sub-rule. At least one of the exits shall lead directly to the exterior or street. mm) Where there is difference in level between connected areas for horizontal exit, ramps not more than 1 in 8 slope be provided, for this purpose steps shall not be used. nn) Doors in horizontal exits shall be openable at all times. oo) Ramps with a slope of not more than 1 in 10 may be substituted for the requirements of staircase. For all slopes exceeding 1 in 10 and wherever the use is such as to involve danger of slipping, the ramp shall be surfaced with non-slipping material. pp) In any building not provided with automatic fire alarm, a manual fire alarm system shall be provided if the total capacity of the building is over 500 persons, or if more than 25 persons are employed above or below the ground floor, except that no manual fire alarm shall be required in one- storey buildings where the entire area is undivided and all parts thereof are clearly visible to all occupants. qq) The Chief Inspector may by an order in writing exempt any factory or part of it from all or any of the provisions of this rule to such extent and on such conditions as may be deemed necessary. Rule 81. Means of Escape for Cotton Ginning Factories:- 72 Notwithstanding anything contained in rule 80 cotton ginning factories shall be provided with at least two suitable ramps or two flights of stairs made of brick work or other fire- resisting material. Rule 82. Fire-fighting apparatus and water supply:- 1. First-aid fighting equipment - In every factory there shall be provided and maintained adequate and suitable fire fighting equipment for fighting fires in the early stages, those being referred to as first-aid fire fighting equipment in this rule. The types of first-aid fire fighting equipment to be provided shall be determined by considering the different types of fire risks which are classified as follows:- “Class A fire” - Fire due to combustible materials such as wood, textiles, paper, rubbish and the like. “Light hazard” - Occupancies like offices, assembly halls, canteens, rest-rooms, ambulance rooms and the like; “Ordinary hazard” - Occupancies like saw mills, carpentry shop, shall timber yards, book binding shops, engineering workshop and the like; “Extra hazard” - Occupancies like large timber yards, godowns storing fibrous materials, flour mills, cotton mills, jute mills, large wood working factories and the like; “Class B fire” - Fire in flammable liquids like oil, petroleum products, solvents, grease, paint, etc. “Class C fire” - Fire arising out of gaseous substances. “Class D fire” - Fire from reactive chemicals, active metals and the like. “Class E fire” - Fire involving electrical equipment and delicate machinery and the like. 2. In every factory adequate provision of water-supply for fire fighting shall be made and where the amount of water required in liters per minute is 550 liters or more as calculated from the formula mentioned below, power-driven trailer pumps of adequate capacity shall be provided and maintained:- A + B + C + D Water required in liters per minute = 20 A = the total area in square meters of all floors including galleries in all buildings of the factory. B = the total area in square meters of all floors and galleries including open spaces in which combustible materials are handled or stored. C = the total area in square meters of all floors and over 15 meter above ground level and D = the total area in square meters of all floors of buildings other than those of fire resisting construction provided fire-resisting constructions of various floors is so certified by any Fire Association of Fire Insurance Company; Provided that, in areas where the fire risk involved does not require use of water such areas under B,C, or D may, for the purpose of calculation be halved; Provided further that, where the areas under B,C,D are protected by permanent automatic fire-fighting installations approved by any Fire Association or Fire Insurance Company, such area/areas may, for the purpose of calculation be halved; 73 Provided also that, where the factory is situated at not more than 3 kilometers from an established city or town fire service, the pumping capacity based on the amount of water arrived at by the formula above may be reduce by 25 percent but no account shall be taken of this reduction in calculating water supply required under sub-rule (2) 3) Each trailer pump shall be provided with equipments as given schedule A. such equipment shall conform to Indian Standard specifications whenever they exist. 4) Trailer pump shall be housed in a separate shed which shall be sited close to a principal source of water supplies in the vicinity of the main risks of the factory. 5) In factories where the area is such as can not be reached by man hauling of trailer pumps within reasonable time, vehicles with towing attachment shall be provided at the scale of one for every four trailer pumps with a minimum of one such vehicle kept available at all times. 6) Water-supply shall be provided to give flow of water as required under sub-rule (2) for at least 100 minutes. At least 50 percent of this water-supply or 4.50,000 litres which ever is less shall be in the form of overhead tanks of adequate capacities(not less than 45,000 litres each) distributed round the factory with due regard to the potential fire risks in the factory, (where piped supply is provided, the size of the main shall not be less than 15 cm. diameter and it shall be capable of supplying minimum of 4,500 litres per minute at a pressure of not less than 7kg/sq cm. Every type of portable fire extinguisher shall be kept mounted in a position approved by the Inspector. Provided that where the Chief Inspector is of the opinion that other adequate fire- fighting apparatus or permanent automatic fire-fighting installation approved by any recognized Fire Association or Fire Insurance Company are provided in the factory building or room, he may issue a certificate in writing (which he may at his discretion revoke) specifying the extent to which the above requirements are relaxed in respect of that building or room. a) Every portable fire extinguisher to be provided shall - i) conform to the appropriate Indian standards specifications; ii) be kept charged ready for use properly mounted in a position approved by the Inspector and in accordance with the makers recommendation. iii) be examined, tested or discharged periodically in accordance with the makers recommendation. b) The manager of every factory shall keep and maintain, sufficient number of spare charges for each type of extinguisher provided in the factory with minimum of 12 spare charges always in stock and readily available. 7) Each factory shall detail a trained officer who shall be responsible for the proper maintenance and upkeep of all fire-fighting equipments. 8) If the Chief Inspector is satisfied in respect of any part of the factory that owing to the exceptional circumstances such as inadequacy of water supply or for infrequency of the manufacturing process or for any other reason, to be recorded in writing all or any of the requirements of the rules are impracticable or not necessary for the protection of workers, he may by order in writing (which he may at his discretion revoke) exempt such factory or part of that factory from all or any of the provisions of the rules subject to conditions as he may by such order prescribe. Schedule – A 74 Equipment of trailer Pumps. ---------------------------------- A. For light trailer pump (680 litres/min) Nine metres length of armoured suction hose, with wrenches. 1 Metal suction strainer 1 Basket strainer 1 Two-way suction collecting-head 1 Suction adaptor. 10 Twenty-five metres lengths of unlined 75 mm delivery hose complete with quick-release couplings. 1 Dividing breeching-piece 2 Branch-piece with 15 mm nozzles. 1 Diffuser nozzle 1 Standpipe with blank cap 1 Hydrant key. 4 Collapsible canvas buckets. 4 Fire hook (preventor) with cutting edge. 1 C.T. Co extinguisher one litre capacity. 1 Thirty metres length ofl 25 mm manila rope. 1 Nine metres extension ladder (where necessary). 1 Heavy axe. 1 Spade. 1 Pick, axe. 1 Crowbar. 1 Saw. 1 Hurricane lamp. 1 Electric torch. 1 Pair rubber gloves. B. For large trailer Pump (1,800 litres /min) - Nine metres length of armoures suction hose, with wrenches. 1 Metal strainer. 1 Basket strainer. 1 Three way suction collecting head. 1 Suction adaptor. 14 Twenty-five metres length of unlined canvas 75 mm. delivery horses complete with quick-release coupeings. 1 Dividing breech-piece. 1 Collecting breaching-piece. 4 Branch pipes with one 25 mm, two 20 mm and one diffuser nozzles. 2 Standpipe with blank caps. 2 Hydrant keys. 6 Collapsible canvas buckets. 1 Ceiling hook (preventor) with cutting edge. 1 C.T.C. extinguisher one litre capacity. 1 Thirty metres length of 50 mm. manila rope. 1 Mine metres extension ladder (where necessary) 1 Pair rubber gloves. 1 Heavy ake. 1 Spade. 1 Pick-axe. 1 Crowbar. 1 Saw. 75 1 Hurricane lamp. 1 Electric, torch. Notes:- If it appears to the Chief Inspector of Factories that in any factory the provisions of breathing apparatus is necessary, he may by order in writing require the occupier to provide suitable breathing apparatus in additing to the equipment for light trailer pump or large trailer pump, as the case may be. Rule 83. Ladders.- The ladder should be suitable for the job, of adequate length and of sound construction. Ladder should be provided with nonskid device at both ends. The ladder should be firmly secured at top and should have at least 1 metre extension above the platform or working point. When used, there should be not less than 750 angle of the vertical rise and the base. Rule 84. Protection of workers attending to prime movers.- 1. In every factory the work of oiling or attending to prime movers shall be done only by a specially trained adult male worker authorized to do such work whose name has been recorded in a register separately maintained for the purpose. 2. Every such worker while oiling or attending to prime mover shall wear tight- fitting clothing. 3. A worker required to wear tight-fitting clothing under sub rule(2) shall be provided by the occupier with clothing which shall consist of at least a pair of closely fitting shorts and a closely fitting half-sleeve shirt or vest. Such clothing shall be returned to the occupier on termination of service or when new clothing is provided. Rule 85. Polymerizing or Curing Machine. - 1. The following precautions shall be taken when fabrics are processed in polymerizing or curing machine for fixing prints by the Emulsion Technique namely:- i) Printed fabrics shall be thoroughly dried by passing them over drying cans or through a hot fuel or other equally effective means, before the same are allowed to pass through the polymerizing machine. ii) The exhaust flap or damper shall be provided with a hole or opening so that at least two-third of it is always open. iii) Infra-red ray heaters of the machines shall be cut off while running the prints. iv) The electrical heater shall be connected to a separate circuit and shall be provided with an isolation switch so as to ensure that it is completely cut of in an emergency. v) The drive of the exhaust fan shall be interlocked with the main drive of the machine in such a way that if the exhaust motor stops, the machine including all heating devices, shall also stop. vi) The electrical heaters shall have thermostat to regulate the temperature, so that the heaters shall be automatically cut off if the temperature rises above the pre-set value. 76 vii) Adequate flap shall be provided on top of the machine, which can open and let off the fumes in the case of an explosion. viii) Filter guaze shall be cleaned at least once a week. ix) Exhaust duct shall be clean at least once a week. x) Tension of the V belt drive of the fans shall be checked every week. 2. The machine shall be examined, under the direct supervision of a responsible person designated by the occupier or manager, who by his experience and knowledge of necessary precautions against risk of explosion, is fit to supervise such work. 3. A register shall be maintained in which the details of various checks carried under sub-rule (2) shall be entered and every entry made therein shall be signed by the person making the checks. Rule 86. Safety Measure in Factories where Equipments of Pipelines Containing Inflammable Materials are Operated. - I) The system of work-permits shall be introduced and unless the equipment or the pipeline is certified to be free of inflammable gas or liquid, no person shall be allowed to enter or open the same. II) The work of opening such equipment or pipe line shall not be commenced unless the following operations are carried out and checked by the Supervisor in-charge of the Process Department of the Factory:- i) Blanking operation.- The equipment or pipeline to be opened for repairs or maintenance shall be effectively blanked so as to ensure that no inflammable gas or liquid can enter the same under any circumstances during the operation or repairs or maintenance. The Supervisor of the process Department shall check personally these operations and shall certify accordingly. ii) Flushing operation.- The Supervisor of the Process Department shall carry out the steaming or flushing out with water of the equipment or pipeline to ensure that all inflammable material is removed from the equipment or pipeline and shall certify to that effect. III) i) Opening of the equipment.- The Supervisor of the Engineering Department of the factory in-charge of the work of opening of such equipment of pipeline, or getting clearance from the Supervisor in charge of the Process Department, shall satisfy himself that the above operations are complete and shall sign the work permits issued by the Supervisor of the process Department. ii) It shall be the joint responsibility of the Supervisor of the Process Department and the Supervisor of the Engineering Department to check and ensure that hot lines, if any, in ;the vicinity of such works are properly screenced, in accordance with the safety instructions of the factory management. The work permit shall have as specific entry for this operation which shall be signed by both the Supervisors. IV) No part of the running equipment or pipeline shall be opened unless a gas test is conducted by a responsible person to ensure that the equipment or pipeline is safe for opening. 77 V) No workers whose clothes have been contaminated with inflammable material shall be allowed to work where any such running equipment or pipeline is being opened. VI) The Safety Officer or any officer authorized by him, shall have system of random checking on the work permits issued and he shall report any serious deficiencies to the Works Manager directly. VII) All drains of such equipments or pipeline shall be laid into the drains to prevent any splashing of the draining inflammable liquids or gases. VIII) Before commencing the opening operation, it shall be ensured that a specific person trained in fire-fighting operations is kept available and his presence shall be ensured throughout the operation of the opening of the equipment. Rule 87. Safety Measure in Gas Works. - In respect of any factory where inflammable gas is produced by carbonization of a coal, oil or any other similar substance, the following provisions shall be complied with, namely:- i) No pipe, valve or any cover of any equipment into which gas is normally allowed to flow shall be opened unless it is ensured that the equipment is no more supplied with any inflammable or explosive gas at a pressure greater than atmospheric pressure. ii) Before undertaking repairs of every sort to any pipe, valve or any other equipment connected with any part in the plant or machinery of any gas works (not being a gas-holder) it shall be ensured that the gas under pressure does not reach the point where such pipe, valve or equipment is being opened by the removal of any bolts and nuts or by cutting either by mechanical means or by application of heat and that such pipe, valve or equipment is so isolated from the gas-holder or any other equipment generating gas that no gas under the pressure reaches the point of repair. iii) Before loosening the bolts and nuts or before undertaking the cutting or any pipe, valve or equipment in any gas works, a definite test shall be carried out by a competent person that no gas under pressure is fed to the point of repair. Details of the test carried out shall be mentioned in a certificate which shall be signed by the competent person. A copy of such certificate shall be displayed prominently near the plane of repair and shall be made available on demand to every worker employed in connection with such repairs for his perusal. iv) Every worker employed in connection with such repairs and working near any pope, valve or other equipment while it is being opened shall be supplied with a mask and a respirator fed by air fresh from a point away from the point of repair. It shall be ensured that the worker shall wear the respirator while working near the point of repair. v) Electrical wiring, or any electrical equipment (not being electrical or welding equipment) used near the point of repair shall be so arranged that there are no trailing cables along the floor. All electrical equipment shall be of flame-proof type: Provided that the provisions of this rule shall not apply to mains and services, plant or machinery installed in the open air subject to the following conditions: 78 a) The main or service shall be situated in the open air, and it shall contain only the following gases, separately or mixed at a pressure greater than atmospheric pressure, namely, town gas, coke oven gas , producer gas, blast furnace gas or gases other than air, used in their manufacture; b) The main or service shall not contain acetylene or any gas or mixture of gases to which acetylene has been intentionally added,; c) The operation shall be carried out by an experienced person or persons and at least two persons (including those carrying out the operations) experienced in work on gas mains and over 18 years of age shall be present during the operation; d) The site of the operation shall be free from any inflammable or explosive gas or vapour; e) Where acetylene gas is used as a source of heat in connection with an operation, it shall be compressed and contained in a porous substance in a cylinder; and f) Prior to the application of any flame to the gas main or service, this shall be pierced or drilled and the escaping gas ignited. Explanation – 1) It shall not be considered effective measure to stop the gas under pressure from reaching the point of repair if only an inflated bladder causes the obstruction between the source of gas under pressure and the point of repair; Provided that where gas valves cannot be provided, it shall be considered an effective measure to stop the gas pressure from reaching the point of repairs if inflated bags alone are inserted against gas pressure not in excess of those indicated below:- Diameter of gas main Pressure in inches of water guage Upto and including 4 10 5 to 10 8 11 to 17 6 18 to 24 5 over 24 3 and a competent person is kept constantly during the operation to watch and control the pressures within the limits specified as above and that - Such bags must be tested on site for soundness and at least two spare bags are available onsite. 2) The competent person for the purpose of this rule shall be the Chief Engineer of the factory or a person certified by the Chief Engineer in writing to be the competent person. Rule 88. Fragile Roofs-provision of Crawling Boards etc. - In any factory, no person shall be required to stand or pass over or work on or near any roof or ceiling covered with fragile material like A.C. sheets or similar material through which he is liable to fall in case it breaks or gives way, a distance of more than three metres unless- a) suitable and sufficient ladders, duck ladders or crawling boards, which shall be securely supported, are provided and used; and b) a permit to work on the fragile roof is issued to him each time he is required to work thereon by a responsible person of the factory concerned. 79 Explanation.- Fragile material means sheets made of asbestos cement or made from similar materials such as Perspex, polyester or other types of plastic fibres. Rule 89. Special Safety Precautions for Certain Highly Hazardous Chemical Process.- In respect of any factory engaged in carrying out any hazardous chemical processes or such parts of any processes as are specified in the Schedule annexed hereto the following provisions shall be complied with viz.- 1) Process Hazards.- a) Before commencing any large scale experimental works or any new manufacture, all possible steps shall be taken to ascertain definitely all the hazards involved both from the actual operations and also from the point of view of the chemical reactions. The properties of the raw materials used, the final products to be made and any by products arising during manufacture shall be carefully studied and adequate and suitable provisions shall be made in advance for dealing with any hazards including effects on workers which may be inherent in the process or which may arise during the process of manufacture. b) The plant, machinery or equipment concerned with the hazardous process shall be in-charge of such operators only who have been trained and made thoroughly conversant to be fit persons to be incharge thereof and no other persons shall be allowed to operate the plant, machinery or equipment. The operators shall be regular employees of the occupier and shall in no case be persons who are employed as contract workers. c) The work of the operators shall be supervised on an overall basis by at least one competent person, who for the purpose of this sub rule shall at least be a graduate in Chemical Engineering of Chemical Technology with specialized knowledge in respect of the processes given in the schedule; Provided that the Chief Inspector may accept a graduate in chemistry having adequate knowledge of the processes given in the schedule and also adequate experience and training or any other qualifications, if in his opinion they are equivalent to the qualifications aforesaid. 2) Emergency Instructions.- Simple and special instructions shall be framed to ensure that effective measures will be carried out in cases of emergency, to deal with possible escapes of inflammable explosive, toxic or deleterious gases, vapours, liquid or dusts. These instructions shall be in the language understood by the majority of the workers and shall be displayed in bold letters at prominent places in the different sections concerned. All concerned workers shall be suitably trained and fully instructed in the prompt action to be taken in such emergencies and also in the general hazards encountered in this process. 3) Fire and Explosion Risks. - In any part of the factory where there is a danger due to fire or explosion from inflammable gas, vapour or dust. i) No internal combustion engine and no electric motor or other electrical equipment or instrument capable of generating sparks or otherwise causing combustion shall be installed or used in a building engaged in the processes. All electrical fitting shall be of suitable flame-proof construction. 80 ii) All pipes carrying hot exhaust or chemicals shall be installed outside the plant building and where this is not possible, these pipes including the flanged portion shall be effectively lagged. iii) Where an inflammable atmosphere is likely to occur the soles of footwear worn by workers shall have no metal on them and the wheels of trucks or conveyors shall be constructed of non-sparking materials. Adequate precautions shall be taken to prevent the ignition of explosive or inflammable atmosphere by sparks emitted from locomotives or other vehicles operating in the vicinity. iv) Portable electric hand lamps shall not be used unless of an intrinsically safe type and all portable electric tools and appliances connected by flexible wires shall not be used, unless these are of suitable flame-proof construction. v) No electric arc lamp, no naked light fixed or portable, shall be used and no person shall have in his possession any match or any apparatus of any type for producing a naked light or spark and all incandescent electric lights shall be in double airtight covers. vi) Prominent notices in the language understood by the majority of the workers and legible by day and by night, prohibiting smoking, the use of naked lights and the carrying of matches or any apparatus for producing a naked light or spark shall be affixed at the entrance of every room or place where there is the risk of fire or explosion from inflammable liquid gas, vapour or dust. In the case of illiterate workers, the contents of the notices shall be fully and carefully explained to them when they commence work in the factory for the first time and again when they have completed one week of services. vii) A sufficient supply of spades, scrapers and pails made from suitable non- sparking material shall be provided for the use of persons employed in cleaning out and or removing residues from any chamber, still, tank or other vessels where any inflammable or explosive danger may occur. viii) All machinery and plant, particularly pipe lines, belt drives, stirrer on which static electricity is likely to accumulate shall be effectively earthed. Receptacles for inflammable liquids shall have metallic connections to earthen supply tanks to prevent sparking due to static charge built up. d) Additional Special Precautions. i) The heating of the process, if required, shall not be carried out by immersion or other types of heaters deriving energy from electricity. ii) The steam heating coils placed in the lower part of the vessel shall never be kept uncovered or allowed to be heated dry. A substantial amount of the liquid shall be ensured in the vessel after each operation to ensure this; Provided that in case employing out of vessels filled with high melting products, the steam shall be stopped/disconnected to the heating coils, before draining process is started to ensure that the heating coils are free of steam before they are uncovered. iii) Steam shall be supplied through a pressure reducing valve and a safety valve correctly set to ensure that the critical temperature of the process is not exceeded. iv) A suitable rapture disc shall be provided on the vessel in addition to the usual spring loaded safety valve. The pipe duct leading away from the rupture dise shall be taken out of the work-room shall be straight and without any bends in order to minimize resistance at the time of blowing and to avoid any chance of a secondary vapour/air explosion. v) The vent line of the vessel shall carry a flame arrestor. 81 vi) Breaking of vacuum, if the process is done under vacuum, on account of consideration of special hazards inherent in the process, shall be done only with nitrogen, other suitable inert gas or steam. Compressed air connection to the manifolds of the vessel equipment shall be avoided. vii) There shall be an automatic cut-off device of steam supply or other heating devices as well as of further feed to the vessel set to operate, no sooner the critical temperature is reached, beyond which the reaction, if any, in the vessels is likely to get out of control or reach run-away state. viii) There shall be arrangement such that it would be possible to introduce quickly, preferably chilled water or atleast ordinary cool water circulation in the steam or other heating coils, no sooner the heating element is cut-off or separate coils or jackets for this purpose shall be ;provided for the vessel. ix) An alarm system shall be provided linked to the pressure indicator of the vessel, so that automatically an audible warning will be given as soon as the pressure exceeds the present safe limit. x) There shall be provided at automatic arrangements such that if the mechanical agitation, where so provided, fails on account of failure of motive power or due to broken shaft, broken blades, failing of blades or such other contingencies, the supply of steam or other heating devices as well as further feed of material would stop automatically. 5) Exemptions - If the Chief Inspector is satisfied in respect of any factory or any process that owing to the special conditions or special methods of work adopted or by reason of the infrequency of the process or for other reasons, all or any of the requirement of this rule are not necessary for the protection of persons employed in any factory or any process, he may by order in writing (which he may in his discretion revoke at any time) exempt such factory or such process from all or any of the provisions of this rule, subject to such condition as he may by such order prescribe and he may, in his discretion add, substract or modify each conditions as deemed fit by him at any time. SCHEDULE 1) Nitro or Amino processes meaning the manufacture of nitro or amino derivative of Phenol Toluene and of Benzene or its Comologus and the making of explosives with the aid of any of these substances. 2) Halogenation process meaning the addition or substitution reaction with a wide variety of : a) Chlorination agents and systems such as Chlorine gas, Hydrochloric Acid, Sodium/hypochlorite, Phosgene, Thionyl Chloride (Soc 12) Phosphorus and such others. b) Fluorination agents such as fluorine. c) Bromination agents such as a Bromine. d) Iodination agents such as iodine, in liquid or gas phases. 3) Aromatization and Isomerization process. Rule 90. Planting of Trees. 82 In every factory wherein more than one hundred workers are ordinary employed, the occupier of a factory shall plant and maintain trees within the precints of the factory after the approval of the number, type and layout of trees by the District Forest Officer concerned or any qualified horticulturist. Rule 91. Hand Protection. Adequate protection for the hands shall be available for all workers when using cutting or welding apparatus to which oxygen or any flammable gas or vapour is supplied at a pressure greater than atmospheric pressure or when engaged in machine reveting or in transporting or stacking plates or in handling plates at machines. Rule 92. Head Protection.- When workers are employed in areas where there is danger of falling objects they shall be provided with suitable safety helmets. Rule 92 A. Protective equipment. The Inspector may, having regard to the nature of the hazards involved in work and process carried out, order the Occupier or the Manager in writing to supply to the workers exposed to particular hazard any personal protective equipment as may be found necessary. Rule 93. Provision of Safety Belts and Life-lines. i) Whenever any worker is engaged on work at a place from which he is liable to fail through a distance of more than 2 (two)meters he shall be provided with safety belts equipped with lifelines which are secured with a minimum of slack, to a fixed structure unless any other effective means such as provision of guard rails or ropes are taken to prevent his falling. ii) All safety belts and lifelines shall be examined once in six months by a competent person to ensure that no belt or lifeline which is not in good condition is used and entered in a register which shall be produced before the inspector on demand. Rule 94. Ovens and Driers. 1) Application. - This rule shall apply to ovens and driors, except those used in laboratories or kitchens of any establishment and those which have a capacity below 325 litres. 2) Definition. - For the purpose of this Rule, oven or drier means any enclosed structure receptacle, compartment or box which is used for baking, drying or otherwise processing of any article or substance at a temperature higher than the ambient temperature of the air in the room or space in which the oven or drier is situated, and in which a flammable of explosive mixture of air and a flammable substance is likely to be evolved within the enclosed structure, receptacle, compartment or box or part thereof on account of the article or substance which is baked, dried or otherwise processed within it. 83 3) Separate electrical connection.- Electrical power supplied to every oven or drier shall be by means of a separate circuit provided with an isolation switch. 4) Design, construction, examination and testing.- a) Every oven or drier shall be properly designed on sound engineering practice and be of good construction, sound materials and adequate strength, free from any patent defects and safe if properly used. b) No oven or drier shall be taken into use in a factory for the first time unless a competent person has thoroughly examined all its parts and carried out the tests as are required to establish that the necessary safe systems and controls provided for safety in operation for the processes for which it is to be used and a certificate of such examination and tests signed by that competent person has been obtained and is kept available for inspection. c) All parts of an oven or drier which has undergone any alteration or repair which has the effect of modifying any of the design characteristics, shall not be used unless a thorough examination and tests as have been mentioned in clause (b) has been carried out by a competent person and a certificate of such examination and tests signed by that competent person has been obtained and is kept available for inspection. 5) Safety Ventilation- a) Every oven or drier shall be provided with a positive and effective safety ventilation system using one or more motor-driven centrifugal fans so as to dilute any mixture of air and any flammable substance that may be formed within the oven or drier and maintain the concentration of the flammable substance in air at a safe level of dilution. b) The safe level of dilution referred to in clause (a) shall be so as to achieve a concentration of the concerned flammable substance in air of not more than 25 percent of its lower explosive limit. Provided that a level of concentration in air upto 50 percent of the lower explosive limit of the concerned flammable substance may be permitted to exist subject to installation and maintenance of an automatic device which- i) shows continuously the concentration of the flammable substances in air present in the oven or drier at any instant; ii) sounds an alarm when the concentration of the flammable substance in air in any part of the oven or drier reaches a level of 50 percent of its lower explosive limit; and iii) shuts down the heating system of the oven or drier automatically when the concentration in air of the flammable substance in any part of the oven or drier reaches a level of 60 percent of its lower explosive limit, is provided to the oven or drier and maintained in efficient working condition. c) No oven or drier shall be operated without its safety ventilation system working in an efficient manner. d) No oven or drier shall be operated with a level of dilution less than what is referred to in clause (b). e) Exhaust ducts of safety ventilation systems should be so designed and placed that their ducts discharge the mixture of air and flammable substance away from the workrooms and not near windows or doors or other openings from where the mixture could re-enter the workrooms. f) The fresh air admitted into the oven or drier by means of the safety ventilation system shall be circulated adequately by means of circulating fan or fans through all parts of the oven or drier so as to ensure that there 84 are no locations where the flammable substance can accumulate in the air or become pocketed to any dangerous degree. g) Throttling dampers in any safety ventilation system should be so designed by cutting away a portion of the damper or otherwise, that the system will handle atleast the minimum ventilation rate required for safety when they are set in their maximum throttling position. 6) Explosion panels.- a) Every oven or drier having an internal total space of not less than half cubic metre shall be provided with suitably designed explosion panels so as to allow release of the pressure of any possible explosion within the oven of drier through explosion vents. The area of openings to be provided by means of such vents together with the area of openings of any access doors which are provided with suitable arrangements for their release in case of an explosion, shall be not less than 2200 square centimeter for every one cubic metre of volume of the oven or drier. The design of the explosion panels and doors as above said shall be such as to secure their complete release under an internal pressure of 0.25 kg per square centimeter. b) The explosion releasing panels, shall, as far as practicable, be situated at the roof of the oven or drier or at those portions of the walls where persons do not remain in connection with operation of the oven or drier. 7) Interlocking arrangements.- a) In each oven or drier efficient inter-locking arrangement shall be provided and maintained to ensure that- i) all ventilating fans and circulating fans whose failures would adversely effect the ventilation rate of flow pattern, are in operation before any mechanical conveyor that may be provided for feeding the articles or substances to be processed in the oven or drier is put into operation; ii) failure of any of the ventilating or circulating fans will automatically stop any conveyor as referred to in clause(i) as may be provided, as well as stop the fuel supply by closing the shut off valve and shut off the ignition in the case of gas or oil fired ovens, and in the case of electrically heated ovens switch off the electrical supply to the heaters; iii) the above said mechanical conveyor is set in operation before the above said shut off valve can be energized; and iv) the failure of the above said conveyor will automatically close the above said shut off valve in the case of ovens and driers heated by gas, oil or steam and deactivate the ignition system, or cut off the electrical heaters in the case of electrically heated ovens or furnaces. 8) Automatic preventilation. Every oven or drier heated by oil, gas, steam or electricity shall be provided with an efficient aggangement for automatic preventilation consisting of atleast 3 volume changes with fresh air by operation of safety ventilation fans and the circulating fans (if used) so as to effect purging of the oven or drier of any mixture of air and a flammable substance before the heating system can be activated and before the conveyor can be placed in position. 9) Temperature control.- Every oven or drier shall be provided with an automatic arrangement to ensure that the temperature within does not exceed a safe upper present limit to be decided in respect of the particular processing being carried on. 85 10) Multistage processes.- Wherever materials are to be processed in ovens or driers in successive operations, suitable arrangement should be provided to ensure that the operating temperature necessary for safe operation at each stage are maintained within the design limits. 11) Combustible substances not to drip on electrical heaters or burners flame.- Effective arrangements shall be provided in every oven or drier to prevent dripping of combustible substances on electric heaters or burner flame used for heating. 12) Periodical examination, testing and maintenance.- a) All parts of every oven and drier shall be properly maintained and thoroughly examined and the various controls as mentioned in this rule and the working of the oven or drier tested at frequent intervals to ensure its safe operation by a responsible person designated by the occupier or manager, who by his experience and knowledge of necessary precautions against risks of explosion, is fit to undertake such work. b) A register shall be maintained in which the details of the various tests carried out from time to time under clause (a) shall be entered and every entry made shall be signed by the person making the tests. 13) Training of operators. No person shall be assigned any task connected with operation of any oven or drier unless he has completed 18 years of age and he is properly trained. 14) Polymerising machine.- a) Printed fabric shall be thoroughly dried by passing them oven drying cans or through hot flue or other equally effective means, before the same is allowed to pass through polymerising machines. b) Infrared ray heators of polymerizing machines shall be cut off while running the prints. Rule 95. Reaction vessels and kettles.- 1) This rule applies to reaction vessels and kettles, hereinafter referred to as reaction vessels, which normally work at a pressure not above the atmospheric pressure but in which there is likelihood of pressure being created above the atmospheric pressure due to reaction getting out of contral or any other circumstances. 2) In the event of the vessel being heated by electrical means, a suitable thermostatic control device shall be provided to prevent the temperature exceeding the safe limit. 3) Where steam is used for heating purposes in a reaction vessel, it shall be supplied through a suitable pressure reducing valve or any other suitable automatic device to prevent the maximum permissible steam pressure being exceeded, unless the pressure of the steam in the supply line itself cannot exceed the said maximum permissible pressure. 4) A suitable safety valve or rupture disc of adequate size and capacity shall be provided to effectively prevent the pressure being built up in the reaction vessel beyond the safe limit. Effective arrangements shall be made to ensure that the released gases, fumes, vapours, liquids, or dusts, as the case may be, are led away and disposed of through suitable pipes without causing any hazard. Where flammable gases or vapours are likely to be vented out from the vessel, the discharge end shall be provided with a flame arrestor. 5) Every reaction vessel shall be provided with a pressure gauge having the appropriate range. 6) In addition to the devices as mentioned in the foregoing provisions, means shall be provided for automatically stopping the feed into the vessel as soon as process 86 conditions deviate from the normal limits to an extent which can be considered as dangerous. 1 Wherever necessary, an effective system for cooling, flooding or blanketing shall be provided, for the purpose of controlling the reaction and process conditions within the safe limits of temperature and pressure. 2 An automatic auditory and visual warning device shall be provided for clear warning whenever process conditions exceed the present limits. This device, wherever possible, shall be integrated with automatic process correction systems. 3 A notice pointing out the possible circumstances in which pressures above atmospheric pressure may be built up in the reaction, the dangers involved and the precautions to be taken by the operators shall be displayed at a conspicuous place near the vessel. Rule 96. Examination of eye sight of certain workers.- 1) No person shall be employed to operate a crane, locomative or forklift truck, or to give signals to a crane or locomotive operator unless his eye sight and colour vision have been examined and declared fit by a qualified ophthalmologist to work whether with or without the use of corrective glasses. 2) The eye sight and colour vision of the person employed as reffered to in clause (1) shall be examined at least once in every period of 12 months upto the age of 45 years and once in every 6 months beyond that age. 3) Any free payable for an examination of a person under this sub-rule shall be paid by the occupier and shall not be recoverable from that person. 4) The record of examination or re-examination carried out as required under sub- rule (1) shall be maintained in Form 18. Rule 97. Railways in factories. 1) This shall apply to railways in the precints of a factory which are not subject to Indian Railways Act. 1890 (Central Act IX of 1890). 2) Gateways.- A Gateway through which a railway track passes shall not be used for the general passage of workers into or out of a factory. 3) Barriers and turngates.- a) Where building or walls contain doors or gates which open to a railway track, a barrier about 1 metre high shall be fixed parallel to and about 60 cm. away from the building or wall outside the opening and extending several feet beyond it at either end, so that any person passing out may become aware of an approaching train when his pace is checked at the barrier. If the traffic of the nearest track is all in one direction, the barrier shall be in the form of a ‘L’ with the end of the short leg abutting on to the wall and the other end opening towards the approaching train. b) If the distance between wall and track cannot be made to accommodate such a barrier, the barrier or a turngate shall be placed at the inside of the opening. c) Where a footway passes close to a building or other obstruction as it approaches a railway track, a barrier or a turngate shall be fixed in such a manner that a person approaching the track is compelled to move away from the building or obstruction and thus obtain timely sight of an approaching locomotive or wagon. 4) Crowd.- a) Workers pay-window, first-aid stations and other points where a crowd may collect shall not be placed near a railway track. 87 b) At any time of the day when workers are starting or ending work, all railways traffic shall cease for not less than five minutes. 5) Locomotives.- a) No locomotives shall be used in shunting operations unless it is in good working order. b) Every locomotive and tender shall be provided with efficient brakes, all of which shall be maintained in good working order. Brake shoes shall be examined at suitably fixed interval and those that are worn out replaced at once. c) Water-gauge glasses of every locomotive, whatever its boiler pressure, shall be protected with substantial glass or metal screens. d) Suitable steps and hand-holds shall be provided at the corners of the locomotive for the use of shunters. e) Every locomotive crane shall be provided with lifting and jacking pads at the four corners of the locomotive for assisting in re-railing operations. f) It shall be clearly indicated on every locomotive crane in English and in language understood by the majority of the workers in the factory, for what weight of load and at what radius the crane is safe. 6) Wagons.- a) Every wagon (and passenger coach, if any) shall be provided either with self-acting brakes capable of being applied continuously or with efficient hand brakes which shall be maintained, in good working order. The hand brakes shall be capable of being applied by a person on the ground and fitted with a device for retaining them in the applied position. b) No wagon shall be kept standing within 3 metres of any authorized crossing. c) No wagon shall be moved with the help of crow bars or pinch bars. 7) Riding on locomotive, wagon or other rolling stock.- No person shall be permitted to be upon (whether inside or outside) any locomotive wagon or other rolling stock except where secure foot hold and hand hold are provided. 8) Attention to brakes and doors.- a) No locomotive, wagon or other rolling stock shall be kept standing unless its brakes are firmly applied and, where it is on a gradient, without sufficient number of properly constructed scotches placed firmly in position. b) No train shall be set in motion until shunting jamadar has satisfied himself that all wagon doors are securely fastened. 9) Projecting loads and cranes.- a) If the load on a wagon projects beyond its length, a guard or dumm-truck shall be used beneath the projection. b) No locu-crane shall travel without load unless the jib is completely lowered and positioned in line with the track. c) When it is necessary for a loco-crane to travel with a load, the jib shall not be swung until the loco-crane has come to rest. 10) Loose shunting.- Loose shunting shall be permitted only when it cannot be avoided. It shall never be performed on a wagon not accompanied by a man capable of applying and pinning down the brakes. A wagon not provided with brakes in good working order and capable of being easily pinned down shall not be loose shunted, unless there is attached to it at least another wagon with such 88 brakes. Loose shunting shall not be performed with, or against a wagon containing passengers, live-stock or explosives. 11) Fly-shunting.- Fly shunting shall not be permitted on any factory railway. 12) The shunting jamader.- a) Every locomotive or wagon in motion in a factory shall be in charge of a properly trained jamadar. b) Before authorizing a locomotive or wagons to be moved, the shunting jamadar shall satisfy himself that no person is under or in between or in front of the locomotive or wagons. 13) Hand signals.- The hand signals used by the shunting jamadar by day and night shall be those prescribed by the shunting rules of railways, working under the Indian Railways Act, 1890(Central Act IX of 1890). 14) Night work and for.- a) In factories where persons work at night, no movement of locomotive, wagon or other rolling stock otherwise than by hand shall be permitted between sunset and sunrise unless the tracks and their vicinity are lighted on a scale of not less than 10 lux as measured at the horizontal plane at the ground level. b) In no circumstances shall any locomotive or train be moved between sunset and sunrise or at any time when there is fog, unless it carries a white head light and a red rear light. 15) Speed control.- a) A locomotive or train shall not be permitted to move at a speed greater than seven kilometers per hour. b) A train, locomotive, wagon or other rolling stock shall not be moved by mechanical or electrical power unless it is preceded at a distance of not less than 10 metres during the whole of its journey by a shunting jamadar. He shall be provided with signaling flags of lamp and whistle necessary for calling the attention of the driver. 16) Tracks.- a) The distance (i) between tracks and (ii) between tracks and building, blind walls or other structures and (iii) tracks and materials deposited on the ground shall be respectively not less than:- aa) from centre to centre of parallel tracks, the overall width of the widest wagon of that guage plus twice the width of the door of such a wagon when opened directly outwards plus 1 metre. bb) from a building or structure other than loading platform to the centre of the nearest track, half the overall width of the widest wagon of that gauge, plus the width of its door when opened outwards plus 1.5 metres. cc) from material stocked or deposited alongside the track, on the ground or on a loading platforms, to the centre of the nearest track, half the overall width of the widest wagon of that gauge, plus half the width of its door when opened directly outward, plus 1 metre. b) Sleepers of a track shall be in level with ground and at all crossings of the track width a road or walkway, the surface of the road or walkway shall be in level with the top of the rails. c) All track ends shall be equipped with buffer stops of adequate strength. d) Barriers of substantial construction shall be securely and permanently fixed across any doorway or gateway in a building or in a wall which 89 conceals an approaching train from view, between the building and the track as prescribed in clause (a) of sub-rule (3). e) Where tracks are carried on a gantry, or other elevation, a safe footway or footways with hand rails and toeboards shall be provided at all positions where persons work or pass on foot; and where there is an opening in the stage of an elevated track for dropping of material to a lower level, the position shall be adequately fenced or the opening itself provided with a grill through which a person cannot fall. f) All point leverds shall have their movements parralled to, not across, the direction of the track. g) All loading platforms which are more than 60 c.m. above the level of the ground on which the track is laid and more than 15 metres in length shall be provided with steps at intervals not greater than 15 metres apart to enable the platform to be easily mounted from the track. h) Turn tables on plant railways shall be provided with locking devices which will prevent the tables from turning while locomotives or wagons are being run on or off the tables. i) Workers shall be prohibited from passing under, between or above railway wagons. 17) Crossings.- a) At all crossings of a track with a road or walkway, danger or crossing signs and wherever reasonably practicable, blinking lights or alarm lights shall be provided. At all important crossings, gates or barriers manned by watchman shall be provided. Swinging gates and barriers shall be secured against inadvertent opening or closing. b) All crossing, warning, signs, gates and barriers shall be illuminated during hours of darkness. 18) Duties of drivers and shunters.- It shall be the duty of every driver of a locomotive or a shunter including a shunting jamadar, to report without delay to their superior any defect in permanent way locomotive or rolling stock. 19) Young persons not to be employed as drivers of locomotive or as shunters.- No person who is under 18 years of age and no person who is not sufficiently competent and reliable shall be employed as a driver of locomotive or as a shunter. 20) The Chief Inspector may by an order in writing exempt a factory or part of it from all or any of the provisions of this rule to such extent and on such conditions as he deems necessary. Rule 98. Safety Committee. 1) In every factory- a) Wherein 250 or more workers are ordinarily employed, or b) Which carries on any process or operation declared to be dangerous under Section 87 of the Act; or c) Which carries on ‘hazardous process’ as defined under section 2(cb) of the Act; There shall be a Safety Committee. 2) The representatives of the management on Safety Committee shall include- a) A senior official, who by his position in the organization can contribute effectively to the functioning of the Committee, shall be the Chairman; b) A Safety Officer and a Factory Medical Officer wherever available and the Safety Officer in such a case shall be the Secretary of the Committee; 90 c) A representative each from the production, maintenance and purchase departments. 3) The workers representatives on this Committee shall be elected by the workers. 4) The tenure of the Committee shall be two years. 5) Safety Committee shall meet as often as necessary but at least once in every quarter. The minutes of the meeting shall be recorded and produced to the Inspector on demand. 6) Safety Committee shall have not right to be adequately and suitably informed of- a) potential safety and health hazards to which the workers may be exposed at work-place; b) data on accidents as well as data resulting from surveillance of the working environment and of the health of workers exposed to hazardous substances so far as the factory is concerned, provided that the committee undertakes to use data on a confidential basis and solely to provide guidance and advice on measures to improve the working environment and the health and safety of the workers. 7) Function and duties of the Safety Committee shall include- a) assisting and cooperating with the management in achieving the aims and objectives outlined in the ‘Health and Safety Policy’ of the occupier; b) dealing with all matters concerning health, safety and environment and to arrive at practicable solutions to problems encountered; c) creating safety awareness amongst all workers; d) undertaking educational, training and promotional activities. e) discussing reports on safety, environmental and occupational health surveys, safety audits, risk assessment, emergency and disaster management plans and implementation of the recommendations made in the reports; f) carrying out health and safety surveys and identifying causes of accidents; g) looking into any complaint made on the likelihood of an imminent danger to the safety and health of the and workers and suggesting corrective measures; and h) reviewing the implementation of the recommendations made by it. 8) Where owing to the size of the factory, or any other reason, the functions referred to in sub-rule (7) cannot be effectively carried out by the Safety Committee, it may establish sub-committee as may be required to assist it. Rule 99. Site Appraisal Committee (Rules prescribed under sec 4A sub-section (i) read with sec 112) 1) constitution: The following provisions shall govern the functioning of the Site Appraisal Committee, herein-after, be referred to as the “Committee”, in these rules:- a) The State Government may constitute a Site Appraisal Committee and reconstitute the Committee as and when necessary; b) The State Government may appoint a senior official of the Factories Inspectorate to be the Secretary of the Committee; c) The State Government may appoint the following as members of the committee:- i) a representative of the Fire Service Organization of the State Government; ii) A representative of the State Department of Industries; iii) A representative of the Director General of Factory Advice Service and Labour Institutes, Bombay. 91 2) No member, unless required to do so by a Court of Law, shall disclose otherwise than in connection with the purpose of the Act, at any time any information relating to manufacturing or commercial business or any working process which may come to his knowledge during his tenure as a Member of this Committee. 3) Application for appraisal of sites. a) Application for appraisal of sites in respect of the factories covered under section 2(cb) of the Act shall be submitted to the Chairman of the Site Appraisal Committee. b) The application for site appraisal alongwith 15 copies thereof shall be submitted in the Form 18A. The committee may dispense with furnishing information on any particular item in the Application Form 18A if it considers the same to be not relevant to the application under consideration. 4) Function of the Committee- a) The Secretary shall arrange to register the application received for appraisal of site in a separate register and acknowledge the same within a period of 7 days. b) The Secretary shall fix up meeting in such a manner that all the applications received and registered are referred to the Committee within a period of one month from the date of their receipt. c) The Committee may adopt a procedure for its working, keeping in view the need for expeditious disposal of applications. d) The Committee shall examine the application for appraisal of a site with reference to the prohibitions and restrictions on the location of industry and the carrying on of processes and operations in different areas as per the provisions of Rule 5 of the Environment (Protection) Rules, 1986 framed under the Environment (Protection) Act, 1986. e) The Committee may call for documents, examine experts, inspect the site if necessary and take other steps for formulating its views in regard to the suitability of the site. f) Where the proposed site requires clearance by the Ministry of Industry or the Ministry of Environment and Forests, the application for Site Appraisal will be considered by the Site Appraisal Committee only after such clearance has been received. Rule 100. Health and Safety Policy 1) The occupier of every factory, except as provided for in sub-rule (2), shall prepare a written statement of his policy in respect of health and safety of workers at work. 2) All factories- a) covered under Section 2(m) (i) but employing less than 50 workers; b) covered under Section 2 (m) (ii) but employing less than 100 workers; are exempted from requirement of sub-rule (1); Provided that they are not covered under the First Schedule under Section 2 (cb) or carrying out processes or operations declared to be dangerous under Section 87 of the Act. 3) Notwithstanding anything contained in sub-rule (2), the Chief Inspector may require the occupiers of any of the factories or class or description of factories to comply with the requirements of sub rule (1), if, in his opinion, it is expedient to do so. 4) The Health and Safety Policy should contain or deal with; 92 a) declared intention and commitment of the top management to health, safety and environment and compliance with all the relevant statutory requirements; b) organizational set-up to carry out the declared policy clearly assigning the responsibility at different levels; and c) arrangements for making the policy effective. 5) In particular, the Policy should specify the following; a) arrangements for involving the workers; b) intention of taking into account the health and safety performance of individuals at different levels while considering their career advancement; c) fixing the responsibility of the contractors, subcontractors transporters and other agencies entering the premises; d) providing a resume of health and safety performance of the factory in its Annual Report; e) relevant technique and methods, such as safety audits and risk assessment for periodical assessment of the status on health, safety and environment and taking all the remedial measures; f) stating its intentions to integrate health and safety, in all decisions including those dealing with purchase of plant, equipment, machinery and material as well as selection and placement of personnel; g) arrangements for informing, educating and training and retraining its own employees at different levels and the public, wherever required. 6) A copy of the declared Health and Safety Policy signed by the occupier shall be made available to the Inspector having jurisdiction over the factory and to the Chief Inspector; 7) The policy shall be made widely known by- a) making copies available to all workers including contract workers, apprentices, transport workers, suppliers, etc. b) displaying copies of the policy at conspicuous places; and c) any other means of communication; in a language understood by majority of workers. 8) The occupier shall revise the Safety Policy as often as may be appropriate, but it shall necessarily be revised under the following circumstances:- a) whenever any expansion or modification having implications on safety and health of persons at work is made; or b) whenever new substance(s) or articles are introduced in the manufacturing process having implications on health and safety of persons exposed to such substances. Rule 101. Collection and Development And Dissemination of Information (Rules made under Sec 41B and 112, Material Safety Data Sheet) 1) The occupier of every factory carrying on a hazardous process shall arrange to obtain or develop information in the form of Material Safety Date Sheet (MSDS) in respect of every hazardous substance or material handled in the manufacture, transportation and storage in the factory. It shall be accessible upon request to a worker for reference. a) Every such Material Safety Data Sheet shall include the following information:- i) The identity used on the label; ii) Hazardous ingredients of the substance; iii) Physical and chemical characteristics of the hazardous substance; iv) The physical hazards of the hazardous substance including the 93 potential for fire, explosion and reactivity. v) The health hazards of the hazardous substance, including the potential for fire, explosion and reactivity; vi) The primary route(s) of entry; vii) The permissible limits of exposure prescribed in the Second Schedule under Section 41-F of the Act, and in respect of a Chemical not covered by the said Schedule, any exposure limit used or recommended by the manufacturer, importer or occupier; viii) Any generally applicable precautions for safe handling and use of the hazardous substance, which are known, including appropriate hygienic practices, protective measures during repairs and maintenance of contaminated equipment, procedures for clean-up of spills and leaks; ix) Any generally applicable control measures, such as appropriate engineering controls, work practices, or use of personal protective equipment; x) Emergency and first aid procedures; xi) The date of preparation of the Material Safety Data Sheet, or the last change to it; and xii) The name, address and telephone number of the manufacturer, importer, occupier or other responsible party preparing or distributing and Material Safety Data Sheet, who can provide additional information on the hazardous substance and appropriate emergency procedures, if necessary. b) The occupier while obtaining or developing a Material Safety Data sheet in respect of a hazardous substance shall ensure that the information recorded accurately reflects the scientific evidence used in making the hazard determination. If he becomes newly aware of any significant information regarding the hazards of a substance, or ways to protect against the hazards, this new information shall be added to the Material Safety Data Sheet as soon as practicable. Labelling 2) Every container of a hazardous substance shall be clearly labeled or marked to identify; a) the contents of the container; b) the name and address of the manufacturer or importer of the hazardous substances; c) the physical and health hazards; and d) the recommended personal protective equipment needed to work safely with the hazardous substance. SCHEDULE MATERIAL SAFETY DATA SHEET SAMPLE MODEL SECTION I : MATERIAL IDENTIFICATION Material Name/Identifier 94 Manufacturer’s Name Supplier’s Name Street Address Street Address City State City State Postal Code Emergency Telephone No. Chemical Name Chemical Identity Trade Name and Product use Synonyms Section II HAZARDOUS INGREDIENTS OF MATERIAL Hazardous Approximate CASor LD 50 LC 50 (Specify Ingredients Concentration % UN (Specify species and Numbers species and Route) Route) SECTION III - PHYSICAL DATA FOR MATERIAL Physical State -Gas - Odour and Odour Threshold Specific Gravity Liquid - Solid Appearance, (p.p.m.) Freezing (oC) Vapour Pressure Vapour Evaporation Rate Boiling F (mm) density Point (Air=1) (oC) Solubility in Water PH Density (g/ml) Coefficient of (20C) water/oil distribution SECTION IV FIRE AND EXPLOSION HAZARD OF MATERIAL Flammability _____________ yes _______________ No. If yes, under what conditions _______________________________________________________________ Means of Extinction _______________________________________________________________ Special Procedure Flash point (0 C) and Under Explosion Limit Lower Explosion Limit 95 Method (%by Volume) (%by Volume) Auto-ignition TDG Flammability Hazardous Combustion Temperature90C) Classification Products Explosion Date-Sensitivity Chemical Sensitivity to Static Discharge. Impact SECTION V - REACTIVITY DATA _______________________________________________________________ Chemical Stability -----------yes -------------- No If no under what conditions _______________________________________________________________ Incompatibility to other substances ----------------yes ---------------- No. If yes, which ones _______________________________________________________________ Reactivity and under what conditions _______________________________________________________________ Hazardous Decomposition Products _______________________________________________________________ Material Name/Identifier _______________________________________________________________ SECTION VI - TOXICOLOGICAL PROPERTIES OF MATERIAL _______________________________________________________________ Route of Entry _________ Skin Contact _________ Skin Absorption _______ Eye Contact _________ inhalation Acute ________ Inhalation Chronic _______ Ingestion _______________________________________________________________ Effect of Acute Exposure to Material _______________________________________________________________ Effect of Chronic Exposure to Material Exposure Irritancy of Limit(s) Material Sensitisation to Material Carchinogenicity, Reproductive Effects, Teratogenicity, Mutagenicity SECTION VII - PREVENTIVE MEASURES _______________________________________________________________ Personal Protective Equipment Gloves (Specify) Respiratory (Specify) Eyes (Specify) Footwear (Specify) Clothing (Specify) Other (Specify) Engineering Controls (e.g. ventilation, enclosed process, etc) please Specify. _______________________________________________________________ Leak and Spill Procedures _______________________________________________________________ Waste Disposal _______________________________________________________________ Handling Procedures and Equipment _______________________________________________________________ Storage Requirements _______________________________________________________________ Special Shipping Information 96 _______________________________________________________________ SECTION VIII - FIRST AID MEASURE _______________________________________________________________ Sources used _______________________________________________________________ Additional information _______________________________________________________________ SECTION IX - PREPARATION DATE OF M S D S _______________________________________________________________ Prepared by (Group, Department, etc) (Phone No.) Date _______________________________________________________________ _______________________________________________________________ Rule 102. Disclosure Of Information Of Workers 1) The occupier of a factory carrying on a ‘hazardous process’ shall supply to all workers the following information in relation to handling of hazardous materials or substances in the manufacture, transportation, storage and other processes; a) Requirements of Sections 41B, 41C and 41H of the Act. b) A list of ‘hazardous process’ carried on in the factory; c) Location and availability of all Material Safety Data Sheets as per Rule 101. d) Physical and health hazards arising from the exposure to or handling of substances; e) Measures taken by ;the occupier to ensure safety and control of physical and health hazards; f) Measures to be taken by the workers to ensure safe handling, storage and transportation of hazardous substances; g) Personal Protective Equipment required to be used by workers employed in ‘hazardous process’ or ‘dangerous operations’; h) Meaning of various labels and markings used on the containers of hazardous substances as provided under Rule 101; i) Signs and symptoms likely to be manifested on exposure to hazardous substances and to whom to report; j) Measures to be taken by the workers in case of any spillage or leakage of a hazardous substance; k) Role of workers vis-à-vis the emergency plan of the factory, in particular the evacuation procedures. 1) Any other information considered necessary by the occupier to ensure safety and health of workers. 2) The information required by sub-rule (1) shall be compiled and made known to workers individually through supply of booklets or leaflets and display of cautionary notices at the work places. 3) The booklets, leaflets and the cautionary notices displayed in the factory shall be in the language understood by the majority of the workers and also explained to them. 4) The Chief Inspector may direct the occupier to supply further information to the workers as deemed necessary. 97 Rule 103. Disclosure of Information to the Chief Inspector 1) The occupier of every factory carrying on ‘hazardous process’ shall furnish, in writing, to the Chief Inspector, a copy of all the information furnished to the workers. 2) A copy of compilation of Material Safety Data Sheets in respect of hazardous substances used, produced or stored in the factory shall be furnished to the Chief Inspector, and the local inspector. 3) The occupier shall also furnish any other information asked for by the Chief Inspector from time to time for the purpose of the Act and Rules made thereunder. Rule 104. Information on Industrial Wastes 1) The information furnished under Rule 102 and 103 shall include the quantity of the solid and liquid wastes generated per day, their characteristics and the method of treatment such as incineration of solid wastes, chemical and biological treatment of liquid wastes, and arrangements for their final disposal. 2) It shall also include information on the quality and quantity of gaseous waste discharged through the stacks or other openings, and arrangements such as provision of scrubbers, cyclone separators, electro-static precipitators or similar such arrangements made for controlling pollution of the environment. 3) The occupier shall also furnish the information prescribed in the sub-rules (1) and (2) to the State Pollution Control Board. Rule 105. Review Of The Information Furnished To Workers Etc. 1) The occupier shall review once in every calendar year and modify, if necessary, the information furnished under Rule 102 and 103 to the workers and the Chief Inspector. 2) In the event of any change in the process or operations or methods of work or hen any new substance is introduced in the process or in the event of a serious accident taking place, the information so furnished shall be reviewed and modified to the extent necessary. Rule 106. Confidentiality of Information The occupier of a factory carrying on ‘hazardous process’ shall disclose all information needed for protecting safety and health of the workers to- a) his workers and b) Chief Inspector. as required under Rule 102 and 103. If the occupier is of the opinion that the disclosure of details regarding the process and formulations will adversely affect his business interests, he may make a representation to the Chief Inspector shall give an opportunity to the occupier of being heard and pass an order to the representation. An occupier aggrieved by an order of Chief Inspector may prefer an appeal before the State Government within a period of 30 days. The State Government shall give an opportunity to the occupier of being heard and pass an order. The order of the State Government shall be final. Rule 107. Medical Examination Rules framed under Section 41-B, 41-C and 112-Specified responsibility of the occupier in relation to hazardous process. 1) Workers employed in “hazardous process” shall be medically examined by a qualified medical practitioner hereinafter referred to as Factory Medical Officer, in the following manner:- a) Once before employment, to ascertain physical fitness of the person to the particular job; 98 b) Once in a period of 6 months, to ascertain the health status of all the workers in respect of occupational health hazards to which they are exposed; and in cases where in the opinion of the Factory Medical Officer it is necessary to do so at a shorter interval in respect of any workers. c) The details of pre-employment and periodical medical examination carried out as aforesaid shall be recorded in the Health Register in Form 29. 2) No person shall be employed for the first time without a certificate of Fitness in Form 28 granted by the Factory Medical Officer. If the Factory Medical Officer declares a person unfit for being employed in any process covered under sub- rule(1), such a person shall have the right to appeal to the Inspector who shall refer the matter to the Certifying Surgeon whose opinion shall be final in this regard. If the Inspector is also a Certifying surgeon, he may dispose of the application himself. 3) Any findings of the Factory Medical Officer revealing any abnormality or unsuitability of any person employed in the process shall immediately be reported to the Certifying surgeon who shall in turn, examine the concerned worker and communicate his findings to the occupier within 30 days. If the Certifying Surgeon is of the opinion that the worker so examined is required to be taken away from the process for health protection, he will direct the occupier accordingly, who shall not employ the said worker in the same process. However, the worker so taken away shall be provided with alternate placement unless he is in the opinion of the Certifying Surgeon, fully incapacitated in which case the worker affected shall be suitably rehabilitated. 4) A certifying Surgeon on his own motion or on a reference from an Inspector may conduct medical examination of a worker to ascertain the suitability of his employment in a hazardous process or for ascertaining his health status. The opinion of the Certifying Surgeon in such a case shall be final. The fee required for this medical examination shall be paid by the occupier. 5) The worker taken away from employment in any process under sub- rule (2) may be employed again in the same process only after obtaining the Fitness Certificate from the Certifying Surgeon and after making entries to that effect in the Health Register. 6) The worker required to undergo medical examination under these rules and for any medical survey conducted by or on behalf of the Central or the State Government shall not refuse to undergo such medical examination. Rule 108. Occupational Health Centres 1) In respect of any factory carrying on ‘hazardous process’ there shall be provided and maintained in good order and Occupational Health Centre with the services and facilities as per scale laid down hereunder:- a) For factories employing upto 50 workers - i) the services of a Factory Medical Officer on retainer-ship basis, in his clinic to be notified by the occupier. He will carry out the pre- employment and periodical medical examination as stipulated in rule 107 and render medical assistance during any emergency. ii) a minimum of 5 persons trained in first-aid procedures amongst whom at least one shall always be available during the working period; iii) a fully equipped first-aid box. b) For factories employing 51 to 200 workers - i) An Occupational Health Centre having a room with a minimum floor area of 15 sq.m. with floors and walls made of smooth and 99 impervious surface and with adequate illumination and ventilation as well as equipment as per the schedule annexed to this Rule. ii) a part-time Factory Medical Officer shall be in over all charge of the Centre who shall visit the factory at least twice in a week and whose services shall be readily available during medical emergencies; iii) one qualified and trained dresser-cum-compounder on duty throughout the working period; iv) a fully equipped first aid box in all the departments; c) For factories employing above 200 workers; i) One full-time Factory Medical Officer for factories employing upto 500 workers and one more Medical Officer for every additional 1000 workers or part thereof; ii) an Occupational Health Centre having at least 2 rooms each with a minimum floor area of 15 sq. metre with floors and walls made of smooth and impervious surface and adequate illumination and ventilation as well as equipment as per the schedule annexed to this Rule. iii) there shall be one nurse, one dresser-cum-compounder and one sweeper-cum-ward boy through-out the working period. iv) the Occupational Health Centre shall be suitably equipped to manage medical emergencies. 2) The Factory Medical Officer required to be appointed under sub-rule (1) shall have qualifications included in Schedule to the Indian Medical Degree Act of 1916 or in the Schedules to the Indian Medical Council Act, 1956 and posses a Certificate of Training in Industrial Health of minimum three months duration recognised by the State Government; Provided that- i) person possessing a Diploma in Industrial Health or equivalent shall not be required to possess the certificate of training as aforesaid; ii) the Chief Inspector may, subject to such conditions as he may specify, grant exemption from the requirement of this sub-rule, if in his opinion a suitable person possessing the necessary qualification is not available for appointment; iii) in case of a person who has been working as a Factory Medical Officer for a period of not less than 3 years on the date of commencement of this rule, the Chief Inspector may, subject to the condition that the said person shall obtain the aforesaid certificate of training within a period of three years, relax the qualification. 3) The syllabus of the course leading to the above certificate, and the organisations conducting the Course shall be approved by the Directorate General of Factory Advice Service and Labour Institutes or the State Government in accordance with the guidelines issued by the DGFASLI. 4) Within one month of the appointment of Factory Medical Officer, the occupier of the Factory shall furnish to the Chief Inspector the following particulars- a) Name and address of the Factory Medical Officer; b) Qualifications c) Experience, if any, and d) the sub-rule under which appointed. SCHEDULE Equipment for Occupational Health Centre in Factories 1. A glazed sink with hot and cold water always available. 100 2. A table with a smooth top at least 180 cm ×105 cm. 3. Means for sterlizing instruments 4. A couch 5. Two buckets or containers with close fitting lids 6. A kettle and sprit stove or other suitable means of boiling water. 7. One bottle of spiritus ammoniac aromaticus (120ml.) 8. Two medium size sponges 9. Two ‘kidney’ trays 10. Four cakes of toilet preferably antiseptic soap 11. Two glass tumblers and two wine glasses 12. Two clinical thermometers 13. Two tea spoons 14. Two graduated (120 ml) measuring glasses 15. One wash bottle (1000 cc) for washing eyes 16. One bottle (one litre) carbolic lotion 1 to 20 17. Three chairs 18. One screen 19. One electric heater. 20. An adequate supply of tetanus toxide 21. Coramine liquid (60 ml) 22. Tablets-antihistaminic, antispasmodic (25 each) 23. Syringes with needles - 2 cc, 5 cc and 10 cc 24. Two needle holders, big and small 25. Suturing needles and materials 26. One dissecting forceps 27. One dressing forceps 28. One scalpels 29. One stethoscope 30. Rubber bandage-pressure bandage 31. Oxygen cylinder with necessary attachments 32. One blood pressure apparatus 33. One patellar Hammer 34. One peak-flow meter for lung function measurement 35. One Stomach wash set 36. Any other equipment recommended by the Factory Medical Officer according to specific need relating to manufacturing process 37. In addition- 1) For factories employing 51 to 200 workers- 1. Four plain wooden splints 900 mm ×100 mm ×6 mm. 2. Four plain wooden splints 350 mm ×75 mm ×6 mm. 3. Two plain wooden splints 250 mm ×50 mm ×12 mm. 4. One pair artery forceps 5. Injections- morphia, pethidine, atronine, adrenaline, coramine, novacan (2 each) 6. One surgical scissors 2) For factories employing above 200 workers 1. Eight plain wooden splints 900 mm ×100 mm ×6mm. 2. Eight plain wooden splints 350 mm ×75 mm ×6mm. 3. Four plain wooden splints 250 mm ×50 mm 12 mm 4. Two pairs artery forceps 5. Injections - morphia, pethidine, atropine, adrenaline, coramine, novacan (4 each) 101 6. Two surgical scissors Rule 109. Ambulance Van 1) In any factory carrying on ‘hazardous process’ there shall be provided and maintained in good condition, a suitably constructed ambulance van equipped with items as per sub-rule (2) and manned by a full-time Driver-cum-Mechanic and a Helper trained in first-aid, for the purpose of transportation of serious cases of accidents or sickness. The ambulance van shall not be used for any purpose other that the purpose stipulated herein and will normally be stationed at or near to the Occupational Health Centre; Provided that a factory employing less than 200 workers may make arrangements for procuring such facility at short notice from a nearby hospital or other places, to meet any emergency. 2) The Ambulance should have the following equipment a) General - A wheeled stretcher with folding and adjusting devices; with the head of the stretcher capable of being tilted upward; - Fixed suction unit with equipment; - Fixed oxygen supply with equipment; - Pillow with case; -Sheets; -Blankets; -Towels; - Emesis bag; -Bed pan; -Urinal pan; -Glass b) Safety equipment - Flares with life of 30 minutes; - Flood lights; - Flash lights; -Fire extinguisher dry powder type; - Insulated gauntlets c) Emergency Care Equipment i) Resuscitation - Portable suction unit; Portable oxygen units; - Bag-valve-mask, hand operated artificial ventilation unit; - Airways; -Mouth gags; -Tracheestomy adapters; - Short spine board; -I.V. Fluids with administration unit; - B.P. Manometer; -Cugg; -Stethoscope ii) Immobilization - Long and short padded boards; - wire ladder splints; - Triangular bandage; - Long and short spine boards iii) Dressings - Gauze pads -4” ×4” ; -Universal dressing 10” ×36”; - Roll of aluminium foils; - Soft roller bandages 6” ×5 yards; - Adhesive tape in 3” roll; - Safety pins: - Bandage sheets; -Burn sheet; iv) Poisoning - Syrup of Ipecac; -Activated Charcoal Pre packeted in dozes; snake bite kit; v) Emergency Medicines - As per requirement (under the advice of Medical Officer only) Rule 110. Decontamination Facilities In every factory, carrying out ‘hazardous process’ , the following provisions shall be made to meet emergency:- a) fully equipped first aid box; b) readily accessible means of water for washing by workers as well as for drenching the clothing of workers who have been contaminated with hazardous and 102 corrosive substance; and such means shall be as per the scale shown in the Table below- TABLE No. of persons employed at any time i) Upto 50 workers ii) Between 51 to 200 Workers iii) Between 201 to 500 workers iv) 501 workers and above. No. of drenching showers 2 2 + 1 for every additional 50 or part thereof. 5 + 1 for every additional 100 or part thereof 8 + 1 for every additional 200 or part thereof. c) a sufficient number of eye wash bottles filled with distilled water or suitable liquid, kept in boxes or cupboards conveniently situated and clearly indicated by a distinctive sign which shall be visible at all times. Rule 111. Making Available Health Records To Workers 1) The occupier of every factory carrying out a ‘hazardous process’ shall make accessible the health records including the record of worker’s exposure to hazardous process or, as the case may be, the medical records of any worker for his perusal under the following conditions:- a) Once in every six months or immediately after the medical examination whichever is earlier; b) If the Factory Medical Officer or the Certifying Surgeon as the case may be, is of the opinion that the worker has manifested signs and symptoms of any notificable disease as manifested signs and symptoms of any notificable disease as specified in the Third Schedule of the Act; c) If the worker leaves the employment; d) If any one of the following authorities so direct - the Chief Inspector of Factories; - the Health Authority of the Central or State Government; - Commissioner of Workmen’s Compensation; - the Director General, Employees State Insurance Corporation; - the Director General, Factory Advice Service and Labour Institutes. 2) A copy of the upto date health records including the record of worker’s exposure to hazardous process or, as the case may, the medical records shall be supplied to the worker on receipt of an application from him. X-ray plates and other medical diagnostic reports may also be made available for reference to his medical practitioner. Rule 112. Qualifications etc. of Supervisors 1) All persons who are required to supervise the handling of hazardous substances shall possess the following qualifications and experience: a) i) A degree in Chemistry or Diploma in Chemical Engineering or Technology with 5 years experience; or ii) A Master’s Degree in Chemistry or a Degree in Chemical Engineering or Technology with 2 years experience. The experience stipulated above shall be in process operation and maintenance in the Chemical Industry. 103 b) The Chief Inspector may require the supervisor to undergo training in Health and Safety. 2) The syllabus and duration of the above training and the organisations conducting the training shall be approved by the DSFASLI or the State Government in accordance with the guidelines issued by the DGFASLI. Rule 113. Issue Of Guidelines For the purpose of compliance with the requirements of sub-sections (1) (4) and (7) of Section 41-B or 41-C the Chief Inspector may, if deemed necessary, issue guidelines from time to time to the occupiers of factories carrying on ‘hazardous process’. Such guidelines may be based on National Standards, Codes of Practice, or recommendations of International Bodies such as ILO and WHO. Rule 114. Quality of personal protective equipment. All personal protective equipments provided to workers as required under any of the provisions of the Act, or the rules shall have certification by Indian Standard Institute. Rule 115. Protective equipment.1 & 2 (1) All workers should be mandatorily provided with Personal Protective Equipments (PPEs) as required under any of the provisions of the Act or the Rules and such PPEs shall conform to the relevant National Standards. The occupiers shall require the workers to use such PPEs and the same shall be maintained in proper working conditions by the occupier. No charge what so ever shall be charged by the occupier from the workers for provision of such PPEs. (2) Without prejudice to the generality of the provisions of sub-rule(1), the various types of PPEs to which this rule shall extend for use in factories shall be as prescribed below. i. Safety Helmet - All workers who are likely to be exposed to any hazard which may cause head injury shall be provided with safety helmets conforming to relevant National Standards. All the workers shall be adequately trained on proper use of such PPEs. When work at height is being carried out such safety helmet shall be provided with a nape strap. No safety helmet which has resisted an impact shall be reused. Periodic cleaning and visual inspection to check any deformation in size or shape shall be carried out. ii. Protective Footwear - Protective footwear should be provided to workers who are exposed to hazards which are likely to cause injury to them by way of materials being dropped on their feet or nail or other sharp objects penetrating their sole. The type and nature of foot wear to be used at workplaces shall be decided by the occupier based on nature of work being carried at such work places. Proper disinfection shall be carried out to prevent contagious fungal infection of the skin that causes scaling, flaking, and itching of the affected areas. Proper medical care shall be carried out to prevent workers from suffering from ingrown nails, metalarsalgia, heel spur, hammer toes and never damage after wearing safety shoe. 1Sixth Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/1841 dtd., 29.11.2019. 2Tenth Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/2199-07 dtd., 27.01.2021 iii. Safety Goggles and Spectacles – The relevant National Standard shall be applicable for eye-protection intended for use in industrial undertakings to provide protection for the eyes of the workers against hazards such as flying particles and fragments, splashing materials and molten metal’s harmful dust, gases or vapours, aerosols and radiations which are likely to impair vision or damage the eyes. Additional eye-protection over their prescription lenses shall be used ensuring that the protective eyewear does not disturb the proper positioning of the prescription lenses. iv. Equipment for eye and face protection during welding – Relevant National Standard shall be followed for the requirements of goggles, hand shield and helmet intended to protect an operator above the shoulder from harmful radiation, spark and particles of hot metal during welding, cutting and similar operations employing a gas flame or electric arc. v. Gloves and Protective Clothing - Suitable gloves, leather gauntlets and mittens conforming to relevant National Standard shall be used for protection of hand of the workers from getting injured. Such protective gloves shall be provided where the hands are exposed to hazards such as those from skin absorption of harmful substances; severe cuts or lacerations; severe abrasions; punctures; chemical burns; thermal burns; and harmful temperature extremes. Suitable protective clothing as per relevant National Standard available for apron (Rubberized, acid and alkali resistant) shall be used for protection of workers who are likely to be exposed to any hazard which may cause injury to their skin. vi. Ear Protection when exposed to noise - Protection against the effects of noise exposure shall be provided when the sound levels exceed the prescribed standards. The relevant National standard shall be followed while selection of suitable ear protection. Periodic disinfection of reusable ear protectors shall be carried out to eliminate hearing loss caused by infection, discharge, pain etc. in the ear. vii. Respiratory Protection - Respiratory Protective equipment based on the nature of hazard as per the relevant National Standard shall be provided by the occupier of the factory to the workers for their respiratory protection against dust, fumes, gases, particulates etc. Clinical examination and appropriate medical tested shall be undertaken to avoid Irritant dermatitis, nose bridge sores, etc. because of prolong use of respiratory personal protective equipment. viii. Other Protective Equipment - Appropriate personal protective equipment based on the nature of hazards as per the relevant National Standard shall be provided by the occupier to the workers. These shall include the following:- a. Safety harnesses with independently secured lifelines where protection against falls cannot be provided by other appropriate means. b. Life vests and life preservers where there is a danger of falling into water. c. Distinguishing clothing or reflective devices or otherwise conspicuously visible material when there is regular exposure to danger from moving vehicles. (3) The Inspector may, having regard to the nature of the hazards involved in work and process being carried out, order the occupier or the manager in writing to supply to the workers exposed to particular hazard any personal protective equipment conforming to relevant National Standard and if no such National standard is available, they shall confirm to international standards. (4) The personal Protective Equipment not having relevant National standard shall be: a. Compliant with EN (European Standard) or ANSI American National standards Institute) or ISO (International Organization for Standardization) as modified from time to time till the relevant National Standard(s) is made available. b. Certified by DGFASLI, if such personal protective equipment are compliant with international standard other than those standards specified under sub rule (a) c. Used after only thorough testing by NABL accredited test facility adhering to such test procedure, prescribed under the relevant international standard(s) as modified from time to time by the Ministry of Labour & Employment, Government of India. Provided that the Personal Protective Equipment not having relevant National Standard & conforming to International Standard specified under sub-rules(a) and (b) of rule 4 shall be permitted to be used notwithstanding the requirements specified under sub-rule(c) of rule 4 up to 31.12.2021 after production of testing certificates issued under corresponding international standard for ensuring conformity assessment. Rule 116. Thermic Fluid Heaters:- 1) All heaters shall be of such construction that coils are removable for periodic cleaning, visual inspection and hydraulic test. 2) Suitable arrangements shall be made for cooling the furnace effectively in case of power failure. 3) Before restarting the furnace, it shall be effectively purged. 4) Velocity of flow of the thermic fluid shall not be allowed to fail below the minimum recommended by the manufacturers while the heater is in operation. 5) The thermic fluid shall be circulated in closed circuit formation with an expansion-cum-deairator tank. This tank shall be located outside the shed where the heater is installed. 6) Every heater shall be provided with a photo-register actuated audio-visual alarm to indicate flame failure and automatic burner cut off. 7) The stack temperature monitor-cum-controller with audiovisual alarm shall be provided so as to warn the operator in case the outlet temperature exceeds the specified minimum. 8) Where inspection doors are provided on the furnace they shall be inter-locked with the burner itself so that they cannot be opened until burner is shut off and furnace is cooled sufficiently. 9) All heaters shall also be provided with the following safety devices:- i) Level control in the expansion tank; ii) Temperature control of thermic fluid; iii) differential pressure switch on the outlet line of the heater tubes; and iv) temperature control device for the fuel oil supply to the burner. 104 10) All devices mentioned in paragraph (9) shall have interlocking arrangement with burner so that in case of any predetermined limits being crossed the supply of fuel and air to burner shall automatically be cut-off. 11) All safety interlocks when operated shall be indicated on the control panel of the heater by a suitable audio-visual alarm. 12) Every heater unit shall be provided as a standard accessory and arrangement for sniffing with low pressure steam or nitrogen for putting out the fire. 13) Electric panel for the heater shall be located near the heater but not so close as to be exposed to spilling or leakage oil. 14) The heater shall be located in a place partitioned off with fire proof material from other manufacturing activities. 15) Explosion vent shall be so installed that release takes place at safe location. 16) The heater coil shall be subjected to pressure test by competent person once atleast in every 12 months. The test pressure shall not be less than twice the operating pressure. 17) If repairs are carried out to the coil, it shall be tested before taking it into use. 18) The thermic fluid shall conform to the specifications prescribed by the manufacturers and shall be tested by competent person for suitability atleast once in every three months period. Such test shall include test for acidity, suspended matter, ash contents, viscosity and flash point. 19) Cleaning of internal surface of the heater or soot and check up of refractory surface on the inside shall be carried out every month or as often as required depending upon working conditions. The coils shall be removed and surface of the coils cleaned thoroughly once at least in a period of six months. The burner, nozzles oil filters and pumps shall be cleaned once a week during the periods of use. 20) A separate register containing the following information shall be maintained:- i) weekly checks carried out confirming the effectiveness of the interlock, ii) weekly checks confirming that all accessories are in good state of repairs, and iii) information regarding fuel oil temperature, pressure, thermic fluid inlet/outlet pressure and temperature, fuel gas temperature, recorded at four hourly interval. 21) The heater when in operation shall always be kept in charge of a trained operator. 105 Chapter V WELFARE Rule Description 117 Washing facilities 118 Facilities for keeping clothing 119 First -Aid Appliances 120 Notice regarding first-aid 121 Ambulance Room 122 Canteens 123 Dining Hall 124 Equipment 125 Prices to be charged 126 Accounts 127 Managing Committee 128 Annual Medical Examination 129 Shelters, Rest Rooms And Lunch Rooms 130 Creches 131 Wash room 132 Supply of Milk & Refreshment 133 Creche staff and clothes for crèche staff 134 Qualification of women-in-charge 135 Exemption From The Provision Of Creche Rule 117. Washing facilities 1. There shall be provided and maintained in every factory for the use of employed persons adequate and suitable facilities for washing which shall include soap and nail brushes or other suitable means of cleaning and the facilities shall be conveniently accessible and shall be kept in a clean and orderly condition. 2. Without prejudice to the generality of the forgoing provisions, the washing facilities shall include- a) a trough with taps or jets at intervals of not less than 60 centimeters; or b) wash basins with taps attached thereto; or c) taps on stand-pipes; or d) showers controlled by taps; or e) circular through of fountain type; Provided that the Inspector may, having regard to the needs and habits of the workers, fix the proportion in which the aforementioned types of facilities shall, be installed. 3. a) Every trough and basin shall have a smooth, impervious surface and shall be fitted with a waste-pipe end plug. b) The floor or ground under and in the immediate vicinity of every through, tap, jet, wash-basin, stand-pipe and shower shall be so laid or finished as to provide a smooth impervious surface and shall be adequately drained. 4. For persons whose work involves contact with any injurious or noxious substance there shall be at least one tap for every fifteen persons, and for persons whose 106 work does not involve such contact the number of taps shall be as prescribed in the schedule annexed hereto. Schedule Number of Workers Number of taps Upto 20 1 21 to 35 2 36 to 50 3 51 to 150 4 151 to 200 5 Exceeding 200 but not 5 plus one tap for every exceeding 500 50 or fraction of 50.0Exceeding 11 plus one tap for every100 or fraction of 100 5. If female workers are employed, separate washing facilities shall be provided and so enclosed or screened that the interiors are not visible from any place where persons of the other sex work or pass. The entrance to such facilities shall bear conspicuous notice “For Women Only” in the language understood by the majority of the workers and shall also be indicated pictorially. 6. The water supply to the washing facilities shall be capable of yielding at least 27 liters a day for each person employed in the factory shall be from a source approved in writing by the Health Officer: Provided that where the Chief Inspector is satisfied that such an yield is not practicable he may by certificate in writing permit the supply of a smaller quantity not being less than 5 liters per day for every person employed in the factory. Rule 118. Facilities for keeping clothing All classes of factories mentioned in the schedule annexed hereto shall provide facilities for keeping clothing not worn during working hours and for the drying of wet clothing. Such facilities shall include the provision of arrangements approved by the Chief Inspector of Factories. SCHEDULE Glass works. Engineering workshops. Iron and steel works. Oil mills. Chemical works. Automobile workshops. Dyeing works. Tanneries. Rule 119. First -Aid Appliances : The first-aid boxes or cup-boards shall be distinctively marked with a red cross on white background and shall contain the following equipments - 107 a) For factories in which the number of persons employed does not exceed ten or (in the case of factories in which mechanical power is not used) does not exceed fifty persons, each first aid box or cup-board shall contain the following equipment:- 1. Six small size sterilized dressings in separate sealed packets. 2. Six medium size sterilized dressings in separate sealed packets. 3. Six large size sterilized dressings in separate sealed packets. 4. Six large size sterilized burn dressings in separate sealed packets. 5. One (60 ml) bottle of 1% cetrimide solution or equivalent antiseptic solution. 6. One (60 ml) bottle of mercurochrome solution (2%) in water. 7. One (30 ml) bottle of liquid ammonia aromatics having the dose and mode of administration indicated on the label. 8. One (60 ml) bottle of tincture of iodine (5%) 9. One pair of surgical scissors (blunt ended) 10. One roll or adhesive plaster (7.5 cm ×1 metre) 11. Six pieces of sterilized eye pads in separate sealed packets 12. Two strips containing 20 tablets of paracetamol (500 mg) or any other substitute. 13. One Undyne eye wash (100 ml) for eye washing or polythene wash bottles with sterile distilled water 500 ml. 14. A M B U Bag - 1 15. Rubber air-ways - 2 16. Splints of suitable sizes 17. One tube of iodoform (topical) ointment. 18. One (30 ml) dark coloured bottle containing potassium permanganate crystals. 19. One cotton wool rolls (100 gm) 20. Tourniquet. 21. Safety Pins -1 dozen 22. Roller bandages 910 cm wide) -12 23. Triangular bandages -1 24. Kidney trays (stainless steel) 25. Artery forceps - 1 pair 26. Dressing forceps - 1 pair 27. Antiseptic soap cake (with case) - 1 28. Torch-light with dry cells - 1 29. Copy of the First aid leaflet issued by the DGFASLI, Govt. of India, Bombay (properly laminated). b) For factories in which mechanical power is used and in which the number of persons employed exceeds ten but does not exceed fifty, each first aid box or cupboard shall contain the following equipment:- 1. Six small size sterilized dressings in separate sealed packets. 2. Six medium size sterilized dressing in separate sealed packets. 3. Six large size sterilized dressing in separate sealed packets. 4. Six large size sterilized burn dressings in separate sealed packets. 5. One (120 ml) bottle of 1% cetrimide solution or equivalent antiseptic solution. 6. One (120 ml) bottle of mercurochrome solution 2% in water. 7. One (60 ml) bottle of liquid ammonia, aromaticus having the dose and mode of administration indicated on the label. 108 8. One (120 ml) bottle containing tincture of iodine (5%) . 9. One pair of surgical scissors (blunt ended). 10. One roll of adhesive plaster (7.5 ×1 metre). 11. Six pieces of sterilized eye pads in separate sealed packets. 12. Two strips containing 20 tablets of paracetamol (500 mg) or any other substitute. 13. Undyne eye wash (100 ml) for eye washing or polythene wash bottle with sterile distilled water 500 ml. 14. A M B U bag - 1 15. Rubber air-ways - 2 16. Splints of suitable sizes. 17. One tube of iodoform (topical) oinment 18. One (30 ml) dark coloured bottle containing potassium permanganate Crystals. 19. Cotton wool rolls (100 gm) each -2 20. Touniquet -1 21. Safety pins -1 dozen 22. Roller bandages (10 cm wide) - 12 23. Triangular bandages - 1 24. Kidney trays (stainless steel) - 1 25. Artery forceps - 1 pair 26. Dressing forceps - 1 pair 27. Antiseptic soap cake (with case) - 1 28. Torch light with dry cells - 1 29. Copy of the first aid leaflet issued by DGFASLI, Govt. of India, Bombay (properly laminated) c) For factories employing more than fifty persons, each first aid box or cupboard shall contain the following equipments:- 1. Twelve small size sterilized dressings in separate sealed packets. 2. Twelve medium size sterilized dressings in separate sealed packets. 3. Twelve large size sterilized dressings in separate sealed packets. 4. Twelve large size sterilized burn dressings in separate sealed packets. 5. Two (120 ml) bottle of 1% cetrimide solution or equivalent antiseptic solution. 6. One (120 ml) bottle of loquor ammonia aromaticus having the dose and mode of administration indicated on the label. 7. One (120 ml) bottle of mercurochrome solution 2% in water. 8. One (120 ml) bottle containing tincture of iodine (5%) 9. Two pairs of surgical scissors (blunt ended) 10. Two rolls of adhesive plaster (7.5 cm ×1) 11. Twelve pieces of sterilized eye pads in separate sealed packets. 12. Four strips containing 40 tabs of paracetamol (500 mg) or any other substance. 13. One Undyne eye wash (100 ml) for eye washing or polythene wash bottles with sterile distilled water 500 ml. 14. A M B U bag - 1 15. Rubber air-ways - 4 16. Splints of suitable sizes 17. Two tubes of Iodoform (topical) oinment 18. One (30 ml) dark coloured bottle containing potassium permanganate crystals. 19. Two cotton wool rolls (100 gm) each. 109 20. Tourniquet - 2 21. Safety pins - 2 dozens 22. Roller bandages (10 cm wide) - 24 23. Traingular bandages - 2 24. Kidney trays (stainless steel) - 2 25. Artery forceps - 2 26. Dressing forceps - 1 pair 27. Antiseptic soap cake with case - 2 28. Torch light with dry cells - 1 29. Copy of the first-aid leaflet issued by the DGFASLI, Govt. of India, Bombay (properly laminated). Rule 120. Notice regarding first-aid. A notice containing the names of the persons working within the precincts of the factory who are trained in first-aid treatment and who are in charge of the first-aid boxes or cupboards shall be posted in every factory at a conspicuous place and near each such box or cupboard. The notice shall also indicate workroom where the said person shall be available. The name of the nearest hospital and its telephone number shall also be mentioned prominently in the same notice. Rule 121. Ambulance Room. 1. Every ambulance room shall be under the charge of at least one whole-time qualified medical practitioner (hereinafter referred to as medical officer) assisted by at least one qualified nurse or dresser-cum-compounder and one nursing attendant in each shift. Provided that where a factory works in more than one shift the Chief Inspector, if he is satisfied that on account of the size of the factory, nature of hazards or frequency of accidents, it is not necessary to employ a whole- time medical officer for each shift separately, may, with the previous approval of the State Government, grant exemption from the provisions of this sub-rule and permit employment of only one whole-time medical officer for more than one or all shifts, subject to the conditions that- a) there shall be no relaxation in respect of nursing staff; and b) the medical officer is readily available on call during the working hours of the factory. 2. There shall be displayed in the ambulance room a notice giving the name, address and telephone number of the medical practitioner in charge. The name of the nearest hospital and its telephone number shall also be mentioned prominently in the said notice. 3. No medical officer shall be required or permitted to do any work which is inconsistent with or detrimental to the responsibility under this rule. 4. The ambulance room shall be separate from the rest of the factory and shall be used only for the purpose of first-aid treatment and rest. It shall have floor area of at least 24 square metres and smooth, hard and impervious walls and floors, and shall be adequately ventilated and lighted by both natural and artificial means. There shall be attached to it at least one latrine and urinal of sanitary type. An adequate supply of wholesome drinking water shall be laid on and the room shall contain at least- i) A glazed sink with hot and cold water always available. ii) A table with a smooth top at least 180 cm ×105 cm. iii) Means for sterilizing instruments iv) A touch 110 v) Two stretchers vi) Two buckets or containers with close fitting lids vii) Two rubber hot water bags viii) A Kettle and spirit stove or other suitable means of boiling water ix) Twelve plain wooden splints 900 mm ×100 mm ×6 mm x) Twelve plain wooden splints 350 mm ×75 mm ×6 mm xi) Six plain wooden splints 250 mm ×50 mm ×12 mm xii) Six woollen blankets. xiii) Three pairs artery forceps xiv) One bottle of spiritus ammoniac aromaticus (120 ml). xv) Smelling salts (60 gm) xvi) Two medium size sponges xvii) Six hand towels xviii) Four “kidney” trays xix) Four cakes of toilet, preferably antiseptic soap. xx) Two glass tumblers and two wine glasses. xxi) Two clinical thermometers xxii) Two tea spoons xxiii) Two granduated (120ml) measuring glasses xxiv) Two mini measuring glasses xxv) One wash bottle (1000 cc) for washing eyes xxvi) One bottle (one litre) carbolic lotion 1 in 20 xxvii) Three chairs xxviii) One screen xxix) One electric hand terch xxx) Four first-aid boxes or cupboards stocked to the standards prescribed under (c) of rule 01 xxxi) An adequate supply of anti-tetanus toxied xxxii) Injections - morphia, pethidine, atropine, adrenaline, coramine, novacan (6 each) xxxiii) Coramine liquid (60 ml). xxxiv) Tablets- antihistaminic, antispasmodic (25 each). xxxv) Syringes with needles - 2 cc, 5 cc, 10 cc and 50 cc xxxvi) Three surgical scissors xxxvii) Two needle holders, big and small xxxviii) Suturing needles and materials xxxix) Three dissecting forceps xl) Three dressing forceps xli) Three scapels xlii) One stethescope xliii) Rubber bandage - pressure bandage. xliv) Oxygen cylinder with necessary attachments. 5. The occupier of every factory to which these rules apply shall for the purpose of removing serious cases of accident or sickness, provide in the premises and maintain in good condition a suitable conveyance unless he has made arrangements for obtaining such a conveyance from a hospital. 6. The Chief Inspector of Factories may, by an order in writing, exempt any factory from the requirements of this rule, subject to such conditions as he may specify in that order, if a hospital, ambulance room or dispensary is maintained at or within 200 metres of the precincts of the factory and such arrangements are made as to 111 ensure the immediate treatment of all injuries sustained by workers within the factory and for providing rest to the workers so injured. Explanation.- For the purpose of this rule, “qualified medical practitioner” means a person holding a qualification granted by an authority specified in the schedule to the Indian Medical Degrees Act, 1916, or in the schedules to the Indian Medical Council Act, 1956. Rule 122. Canteens – 1. The Occupier of every factory wherein more than 250 workers are ordinarily employed and which is specified by the State Government by a notification in this behalf shall provide, in or near the factory, an adequate canteen according to the standards prescribed in the Rules. The canteen shall be available for the use of the workers, within six months from the date of such notification: Provided that the State Government may for sufficient reasons, from time to time by an order in writing, extend the said period in respect of any specified factory. 2. The manager of a factory shall submit for the approval of the Chief Inspector plans and site plan, in duplicate, of the building to be constructed or adapted for use as a canteen. 3. The canteen building shall be situated not less than 15 metres from the latrine, urinal, boiler house, coal stacks, ash dumps and any other source of dust, smoke or obnoxious fumes: Provided that the Chief Inspector may in any particular factory relax the provisions of this sub-rule to such extent as may be reasonable in the circumstances and may require measures to be adopted to secure the essential purpose of this sub-rule. 4. The canteen building shall be constructed in accordance with the plans approved by the Chief Inspector and shall accommodate at least a dining hall, kitchen, store room, pantry and washing places separately for workers and for utensils. 5. In a canteen the floor and inside walls up to a height of 120 centimetres from the floor shall be made of smooth and impervious material; the remaining portion of the inside walls shall be made smooth by cement plaster or in any other manner approved by the Chief Inspector. 6. The doors and windows of canteen building shall be of fly-proof construction and shall allow adequate ventilation. 7. The canteen shall be sufficiently lighted at all times when any person has access to it. a) In every canteen- i) all inside walls of rooms and all ceilings and passages and staircases shall be lime-washed or colour-washed at least one in each year or painted once in three years dating from the period when last lime- washed, colour washed or painted, as the case may be; ii) all wood work shall be varnished or painted once in three years dating from the period when last varnished or painted; iii) all internal structural iron or steel work shall be varnished or painted once in three years dating from the period when last varnished or painted; Provided that inside walls of the kitchen shall be lime washed once every four months. b) Deleted. 9. Precincts of the canteen shall be maintained in a clean and sanitary condition. Waste water shall be carried away in suitable covered drains and shall not be _____________________________________________________________________ 1Tenth Amendment vide No.F.7 (121)-FB/AM (Vol.-II)/2007/2199 dtd. 27.01.2021. 112 allowed to accumulate so as to cause a nuisance. Suitable arrangements shall be made for the collection and disposal of garbage. Rule 123. Dining Hall – 1. The dining hall shall accommodate at a time at least 30 percent of the workers working at a time. Provided that , in any particular factory or in any particular class of factories the State Government may, by a notification in this behalf, alter the percentage of workers to be accommodated. 2. The floor area of the dining hall, excluding the area occupied by the service counter and any furniture except tables and chairs, shall be not less than one square metre per dinner to be accommodated as prescribed in sub-rule (1). Provided that in the case of factories in existence at the date of the commencement of the Act, where it is impracticable, owing to the lack of space, to provide one square metre of floor area for each person, such reduced floor area per person shall be provided as may be approved in writing by the Chief Inspector. 3. A portion of the dining hall and service counter shall be partitioned off and reserved for women-workers, in proportion to their number. Washing place for women shall be separate and screened to secure privacy. 4. Sufficient tables, stools, chairs or benches shall be available for the number of dinners to be accommodated as prescribed in sub-rule (1). Rule 124. Equipment 1. There shall be provided and maintained sufficient utensils, crockery, cutlery, furniture and any other equipment necessary for the efficient running of the canteen suitable clean clothes for the employees serving in the canteen shall also be provided and maintained. 2. The furniture, utensils and other equipment shall be maintained in a clean and hygienic condition. A service counter, if provided, shall have a top of smooth and impervious material. Suitable facilities including and adequate supply of hot water shall be provided for the cleaning of utensils and equipment. Rule 125. Prices to be charged. – 1. Food, drink and other items served in the canteen shall be sold on a non-profit basis and the prices charged shall be subject to the approval of the Canteen Managing Committee: Provided that where a canteen is managed by workers Co-operative society, the prices to be charged may include a margin of profit upto a maximum of 5 per cent of its working capital. 2. In computing the prices referred to in sub-rule (1) the following items of expenditure shall not be taken into consideration, but will be borne by the occupier:- a) the rent for the land and building; b) the depreciation and maintenance charges of the building and equipment provided for the canteen; c) the cost of purchase, repairs and replacement of equipment including furniture, crockery, cutlery and utensils. d) the water charges and expenses for providing lighting and ventilation; e) the interest on the amount spent on the provision and maintenance of the building, furniture and equipment provided for the canteen. f) the cost of fuel required for cooking or heating foodstuffs or water; and 113 g) the wages of the employees serving in the canteen and the cost of uniform, if any, provided to them. 3. The charges per portion of foodstuffs, beverages and any other items served in the canteen shall be conspicuously displayed in the canteen. Rule 126. Accounts 1. All books of account, registers and any other documents used in connection with the running of the canteen shall be produced on demand to an Inspector. 2. The accounts pertaining to the canteen shall be audited, once every twelve months, by registered accountants and auditors. The balance sheet prepared by the said auditors shall be submitted to the Canteen Managing Committee not later than two months after the closing of the audited accounts: Provided that the accounts pertaining to the canteen is a Government Factory having its own accounts department, may be audited in such department. Provided further that where the canteen is managed by a cooperative society registered under the Co-operative Societies Act, the accounts pertaining to such canteen may be audited in accordance with the provisions of the Co- operative Societies Act. Rule 127. Managing Committee – 1. The manager shall appoint a Canteen Managing Committee which shall be consulted from time to time as to - a) the quality and quantity of food stuffs to be served in the canteen; b) the arrangement of the menus c) the times of meals in the canteen; and d) any other matter as may be directed by the Committee; Provided that where the canteen is managed by a co-operative society registered under the Co-operative Societies Act, it shall not be necessary to appoint a Canteen Managing Committee. 2. The Canteen Managing Committee shall consist of an equal number of persons nominated by the occupier and elected by the workers. The number of elected workers shall be in the proportion of 1 for every 1000 workers employed in the factory, provided that in no case shall there be more than 5 or less than 2 workers on the Committee. 3. The manager shall determine and supervise the procedure for elections to the Canteen Managing Committee. 4. A Canteen Managing Committee shall be dissolved by the manager two years after the last election, no account being taken of a bye-election. Rule 128. Annual Medical Examination 1. Annual medical examination for fitness of each member of the canteen staff who handles foodstuffs shall be carried out by the factory medical officer or the Certifying Surgeon, which should include the following - a) routine blood examination at intervals of not more than twelve months. b) routine and bacteriological testing of faeces and urine for germs of dysentery and typhoid fever at intervals of not more than six months; and c) any other examination including chest x-ray that may be considered necessary by the factory medical officer or the Certifying Surgeon. 114 2. Any person who in the opinion of the factory medical officer or the Certifying Surgeon is unsuitable for employment on account of possible risk to the health of others, shall not be employed as canteen staff. 3. The fee for such routine clinical examination of each member of the canteen staff by the certifying surgeons shall be Rs. 25 (twenty five) only which fee is exclusive of any charges incurred for conducting any kind of Laboratory tests etc. 4. Such charges shall be paid by the occupier into the local treasury and receipt attached with the application. Rule 129. shelters, rest rooms and lunch rooms – 1. The shelters or rest rooms and lunch rooms shall conform to the following standards: a) the building shall be soundly constructed and all the walls and roof shall be of suitable heat resisting materials and shall be water proof. The floor and walls to a height of 90 centimeters shall be so laid or finished as to provide a smooth, hard and impervious surface; b) the height of every room in the building shall be not less than 3.65 meters from floor level to the lowest part of the roof and there shall be at least 1.12 square meters of floor area for every person employed; Provided that workers who habitually go home for their meals during the rest periods may be excluded in calculating the number of workers to be accommodated. Provided further that, in the case of rooms in buildings in existence at the date of coming into force of this rule which have been or are intended to be adapted for use as shelters, rest rooms or lunch rooms, as the case may be, the Chief Inspector may approve the rooms having such reduced height as may in his opinion be reasonable in the circumstances of the case on such conditions as may be deemed expedient. c) effected and suitable provision shall be made in every room for securing and maintaining adequate ventilation by the circulation of fresh air and there shall also be provided and maintained sufficient and suitable natural or artificial lighting; d) Every room shall be adequately furnished with chairs or benches with back- rest; e) sweepers shall be employed whose primary duty is to keep the rooms, building and precincts thereof in a clean and tidy condition; and f) suitable provision shall be made in every room for supply of drinking water and facilities for washing. 1) The lunch rooms shall: a) comply with the requirements laid down in clauses (a) to (f) of sub rule (1) ; and b) be provided with adequate number of table with impervious tops for the use of workers for taking food. Rule 130. Creches a) The crèches shall conform to the following standards and the (Occupier or Manager of the factory) shall submit for approval of the Chief Inspector of Factories, detailed plans in triplicate of the building to be constructed or adapted. b) The crèche shall be conveniently accessible to the mothers of the children accommodated therein and so far as is reasonably practicable it shall not be situated in the close proximity to any part of the factory where obnoxious fumes, 115 dust or odours are given off or in which excessively noisy processes are carried on. c) The building in which the crèche is situated shall be soundly constructed and all the walls and roof shall be of suitable heat-resisting materials and shall be water- proof. The floor and internal walls of the crèche to a height of 1.2 metres all-round shall be so laid or finished as to provide a smooth impervious surface. d) The height of the rooms in the building shall be not less than 3.7 metres from the floor to the lowest part of the roof and there shall be not less than 2 square metres or floor area for each child to be accommodated. Provided that in the case of rooms in buildings in existence at the date of the coming into force of this rule which have been or are intended to be adapter for use as a crèche, the Chief Inspector may approve the rooms having such reduced height as may in his opinion be reasonable in the circumstances of the case on such conditions as may be deemed expedient. e) Effective and suitable provision shall be made in every part of the crèche for securing and maintaining adequate ventilation by the circulation of fresh air. f) The crèche shall be adequately furnished and equipped and in particular there shall be one suitable cot or cradle with the necessary bedding for each child (provided that for children over two years of age it will be sufficient if suitable bedding is made available) at least one chair or equivalent seating accommodation for the use of each mother while she is feeding or attending to her child and sufficient supply of suitable toys for the older children. g) A suitably fenced and shady open air playground shall be provided for the older children. Provided that the Chief Inspector of Factories may by order in writing exempt any factory from compliance with this sub-rule if he is satisfied that there is not sufficient space available for the provision of such a playground. Rule 131. Wash room There shall be in or adjoining the crèche a suitable wash room for the washing of the children and their clothing. The wash room shall conform to the following standards:- a) The floor and internal walls of the room to a height of 91.4 centimetres shall be so laid or finished as to provide a smooth impervious surface. The room shall be adequately lighted and ventilated and the floor shall be effectively drained and maintained in a clean and tidy condition. b) There shall be at least one basin or similar vessel for every four children accommodated in the crèche at any one time together with a supply of water provided, if practicable, through taps from a source approved by the Health Officer. Such source shall be capable of yielding for each child a supply of at least 23 litres of water a day. c) An adequate supply of clean clothes, soap and clean towels shall be made available for each child while it is in the creche. d) Adjoining the washing room referred to above, a septic type latrine shall be provided for the sole use of the children in the crèche. The design of this latrine and the scale of accommodation to be provided shall be determined by the Health Officer. The crèche latrine shall always be kept clean and in a sanitary condition by a sweeper specially employed for the purpose. Rule 132. Supply of Milk & Refreshment 116 At least 250 ml of clean pure milk shall be available for each child on every day it is accommodated in the crèche and the mother of such a child shall be allowed in the course of her daily work two intervals of atleast 15 minutes duration each (other than intervals for rest under section 55) to feed the child. For children above two years of age there shall be provided in addition an adequate supply of wholesome refreshment. In case of any dispute regarding wholesome refreshment (item quantity, quality etc) the decision of the Chief Inspector is final. Rule 133. Creche staff and clothes for crèche staff: 1) For each crèche there shall be appointed women in-charge and female attendant at the rate of one attendant for every thirty children or as part thereof exceeding ten to help the women-in-charge. 2) the crèche staff shall be provided with suitable clean clothes for use while on duty. Rule 134. Qualification of women-in-charge: The women-in-charge shall be either a qualified nurse or midwife. Provided that the occupier may appoint nurse as midwife who is not qualified if the Chief Inspector in consultation with the Director of Health Services that the nurse or midwife is suitable for appointment. Rule 135. Exemption from the provision of creche: 1. The provision of section 48 and rules 135-139 shall not apply to any factory which works for less than 190 days in a calendar year or to a factory wherein the number of married women or widows employed does not exceed 15 or the total number of children below the age of 6 years of all the women workers in the factory does not exceed 4, subject to the condition that the alternative arrangements as hereinafter mentioned in sub-rule(2), are provided in the factory. 2. The alternative arrangements required to be provided under sub-rule (1) shall be as follows, namely;- a) A crèche-room which has an area of not less than 10 square metres shall be constructed or adapted for use in accordance with the plans approved by the Chief Inspector. b) The crèche-room shall have suitable wash place for washing of the children and their clothes and adequate supply of clean water, soap and, towels shall always be provided and maintained. c) The crèche-room shall be provided with suitable bedding for the use of the children. d) At least one female attendant shall be employed to lookafter the children in the crèche-room. The female attendant shall be provided with clean clothes for use while on duty. 3. The mother of each child in the crèche-room shall be allowed two intervals of not less than 15 minutes each (such intervals being other than those allowed under section 55) during her working hours to feed the child. 4. The exemption granted under this rule may at any time be withdrawn by the Chief Inspector if he finds, after such enquiry as he may deem fit, that the factory has committed a breach of this rule. 117 Chapter VI Working Hours of Adult Rule Description 136 Compensatory Holidays 137 Muster Roll for Exempted Factories 138 Cash Equivalent 139 Restriction of Double Employments 140 Notice of Periods of work for Adult 141 Register for Adult Workers 142 Persons defined to Hold Positions of Supervision or management 143 Persons Defined to Hold Confidential Position 144 List to be maintained of Persons holding Position of Supervision of management or holding confidential position 145 Exemption of certain Adult Workers Rules prescribed under section 53 (2) Rule 136. Compensatory Holidays 1) Except in the case of workers engaged in any work which for technical reasons must be carried on engaged in any work which for technical reasons must be carried continuously throughout the day, the compensatory holidays to be allowed under sub section (1) of section 53 of the Act shall be so spaced that not more than 2 (two) holidays are given in one week. 2) The manager of the factory shall display, on or before the end of the month which holidays are lost, notice in respect of workers allowed compensatory holidays are lost, notice in respect of workers allowed compensatory holidays during the following month and of the dates thereof, at the place at which the Notice of Periods of Work prescribed under section 61 is displayed. Any subsequent change in the notice in respect of any compensatory holiday shall be made not less than 3 days in advance of the date of holiday. 3) Any compensatory holiday or holidays to which a worker is entitled shall be given to him before he is discharged or dismissed and shall not be reckoned as part of any period of notice required to be given before discharge or dismissal. 4) a) The manager shall maintain a register in Form 19. Provided that, if the Chief Inspector is of the opinion that any master roll or register maintained as part of the routine of the workers in the factory the particulars required for the enforcement of section 53, he may by order in writing direct that such master roll or register or return shall, to the corresponding extent, be maintained in place of and be treated as the register or return required under this rule for that factory. b) This register maintained under clauses (a) shall be preserved for a period of five years after the last entry made in it and shall be produced before the Inspector on demand. Prescribed under section 59(5) Rule 137. Muster Roll for Exempted Factories The manager of every factory: - a) which is exempted under section 5, or 118 b) in which workers are exempted under section 64 or section 65, from the provisions of section 51 ore section 54, shall keep a muster roll in Form 20 showing the normal piece-work rate of play, or the rate of pay per hour, of all the exempted workers in the factories. In this master roll shall be correctly entered the extent of overtime worked by each worker together with the overtime earnings in respect thereof and the dates of the payment of such earnings. The muster roll in Form 20 shall always be available, produced for inspection whenever required by an Inspector. Prescribed under section 59(5) Rule 138. Cash Equivalent The cash equivalent of the advantage through the concessional sale to a worker of food grains and other articles shall be computed at the end of every wage period fixed under provisions of the Payment of Wages Act, 1936. For the purpose of computing the cash equivalent of the advantage accruing through the concessional sale to a worker of food grains and other articles, the difference between the value of food grains and other articles at the average market rates prevailing during the wage period in which there was overtime work, and the value of food grains and other articles supplied at concessional rates shall be calculated and allowed for the overtime hour worked. Provided that in the case of factories which are already following a different procedures for calculating the cash equivalent of the advantage accruing through the concessional sale of food grain and other articles at the time of commencement of this rule the Chief Inspector may be order in writing permit them to adopt such different procedure if it is not less favourable than the one prescribed in this rule. Prescribed under section 60 Rule 139. Restriction of Double Employments An adult worker may be employed, in more than one factory on the same day, with the previous approval of the Inspector, subject to the following conditions: 1) He shall not be employed for more than nine hours in all on any one day. 2) He shall receive a weekly holiday in accordance with the provision of section 52. 3) Every worker who is required to work in another factory on the same day shall carry with him a card in which the following particulars shall be entered by the manager of the first factory: a) his normal periods of work as the notice of periods of work, the day; b) the period or periods he has worked in the first factory for the day. The manager of the second factory in which he is to work for the rest of the day shall enter in the card the period or periods he has worked for the day in his factory. The managers of both the factories in which the worker has worked on the same day shall send to the Inspector an extract of the card mentioned above not later than three days from the date on which the workers has not worked in the two factories on the same day. Prescribed under section 61 (B) Rule 140. Notice of Periods of work for Adult The Notice of Periods of Work for Adult Workers shall be in Form 21. Prescribed under section 62 (2) 119 Rule 141. Register for Adult Workers The register of Adult Workers shall be in Form 22. This register shall be written up a fresh each year and shall be preserved for a period of five years after the date of last entry in it and shall be produced before the Inspector on demand. Prescribed under section 64 Rule 142. Persons defined to Hold Positions of Supervision or management In a factory the following person shall be deemed to hold positions of supervision or management within the meaning of subsection (1) of Section 64, provided they are not required to perform manual labour or clerical work as a regular part of their duties namely: - 1) Asst. Engineer, Jr. Engineer. 2) Labour (Welfare) Officer. 3) Safety Officer. 4) Fire Officer. 5) Foreman, Asst. Foreman, Overseer, Supervisor, Head Supervisor, Shift Supervisor, Chargeman, Chief Draughtsman. 6) Boiler Operation Engineer 7) Head Electrician 8) Weaving Master, Spinning Master. 9) Heads of various department/ Section in a factory in any other designation. 10) Any other person who in the opinion of the Chief Inspector holds a position of supervision or management in the factory and is so declared in writing by him. Rule 143. Persons Defined to Hold Confidential Position In a factory, the following persons shall be deemed to be employed in a confidential position within the wearing of Sub-section (1) of Section 64: - i) Private Secretary, Asst. Private Secretary, Personal Assistant, Stenographer. ii) Telephone Operator, Telex Operator. iii) Time Keeper, Store Keeper, iv) Office Superintendent, Head Clerk, v) Any other person who, in the opinion of the Chief Inspector, holds position of confidential and is so declared in writing by him. Rule 144. List to be maintained of Persons holding Position of Supervision of management or holding confidential position 1) A list showing the Name & Designations of all persons defined in Rule 147 & 148 shall be maintained in every factory and it shall be made available for inspection to the Inspector at all times where work is being carried on in any factory. 2) Where the ordinary rate of wages of any of the persons whose name is shown in the list maintained under sub rule (1) of this rule does not exceed the wage limit specified in Sub-section (6) of Section –1 of the Payment of wage Act, 1936, as amended from time to time the Manager of the factory shall maintain a muster roll in Form 20 as prescribed under Rule 142 in respect of such persons. Rule 145. Exemption of certain Adult Workers Adult workers engaged in factories specified in column 2 of the Schedule here to annexed, on the work specified in column 4 of the said schedule shall be exempt from the provisions of the sections specified in column 5 thereof, subject to the conditions, if any, specified in column 6 of the said schedule; and also subject to the following conditions, namely: - 120 i) No women workers shall be required or allowed to work for more than nine hours in any day; ii) except in respect of exemption under clause (a) of sub-section (2) of section 64, the following limits of work inclusive of overtime shall be observed, namely: - a) the total number of hours of work in any day shall not exceed tens; b) the spread over, inclusive of intervals for rest, shall not exceed twelve hours in any one day. c) the total number of hours in a week, including overtime shall not exceed sixty; and d) the total number of hours of overtime shall not exceed fifty for any one quarter; Provided that, the limits imposed by sub- clauses (a) and (b) of this clause shall not apply in the case of a shift workers engaged in the factories specified against category and No. X (1) to (39) in the Schedule if the said worker is allowed to work the whole or part of the immediate subsequent shift in the absence of a worker who has failed to report for duty. Category Class of Exemption Nature of Exemption Conditions Factory under section Exempted from Work I All factories 64(2)(a) and Urgent, repairs 51,52,54,5 i) The occupier 64(3) for Explanation, 5, 56 and or manager of consequential Urgent repairs 61. the factory shall exemption for the send to the, from the purposes of this Inspector a provisions of exemption shall notice within 24 section 61. mean hours of the (a) repairs to commencement any part of of the work, machinery, starting therein Plant or the precise structure of a nature of urgent factory, which repairs the exact are of such a time of the nature that commencement delay in their of work. A copy execution of such notice would involve shall be danger to displayed in the human life or a factory as safety or the provided under stoppage of the section 108 (2) manufacturing of the Act. process. within 24 hours b) repairs to of completion of deep-sea-ships the work of and repair to urgent repairs a commercial notice to that aircrafts which effects shall be are essential to sent to the enable such Inspector ships or alongwith the aircrafts to copy of entries leave port at made in Form proper time or No. 21 in 121 conditions as respect of every the case may worker be, and mentioned in c) repairs in the earlier connection notice. with a change ii) No worker of motive shall be allowed power e.g. or required to from steam to work on such electricity or repairs for more vice versa, than 15 hours when such on any one day, work cannot 39 hours during possibly be any 3 done without consecutive stoppage of the days or 66 hours normal during each manufacturing period of seven process. consecutive Provided that days urgent repairs commencing shall not from his first include employment on periodical such work cleaning and iii) If the maintenance Inspector is of work. the opinion that any work being carried on in a factory as ‘Urgent Repairs is not Urgent Repairs the Inspector shall serve on the manager an order to that effect and the manager shall in respect of such work, require any worker to work in contravention of the provision of section 51, 52, 54, 55,56 and shall comply with section 61 of the Act. iv) No worker shall be required or allowed to work for the period of more than six hours before has had 122 an interval of rest or food of at least half an hour. v) Provisions of section 53 of the Act and 142 rules shall be compiled with. II All factories 64 (2) for work a) Maintenance 51, 54, 55 i) No worker except those on in the nature of work in and 56 shall be required continuous preparatory or connection or allowed to process. complementary with the mill work on shifts gearing, the of longer than 8 electric driving hours duration. of lighting ii) Intervals for apparatus, the food and rest mechanical or shall be given to electrical lifts all workers or hoists and allowed to work steam or water on such work. pipes or pumps iii) provisions of of the factory; rules 142 shall b) Departmental be compiled boiler and with. c) Workers attending to the starting, stopping and maintaining electrical motors and connected switch gears. III. All factories 64(2) for work 1. a) Work 51,54,55 i) No worker which is performed by and 56 shall be required necessary drivers on or allowed to Intermittent in lighting work on shifts nature. ventilating on of longer than 8 and hours duration. humidifying ii) Intervals for apparatus food and rest b) Work shall be given to performed by all workers firepumpmen allowed to work and all on such work. personnel on iii) Provision of the fire-fighting Rul3 95 and 96 staff shall be 2. Telephone complied with. Operators and Telex Operators. IV All Factories 64(2) (h) for Workers 51, 52 Provisions of work in the engaged in section 53 and Engine room, engine rooms rules 142 shall boiler house or boiler house be complied attending to attending to with. 123 power plant or power plant or transmission transmission machinery or machinery or the prime the prime movers. movers. V. All factories 64(2) (i) work Workers 51, 52, 54, i) No worker of loading and engaged in the 55, 56, 61 shall be required unloading loading or or allowed to unloading of work on shifts railway wagons of longer than 8 or lorries, hours duration. trucks and ii) Intervals for tankers or the food and rest loading and shall be given to unloading at all workers jetties. allowed to work on such work. iii) provisions of rules 142 shall be compiled with. VI Carbonic Acid 64(2) (b) work Work of 51, 54, 55 i) This Gas factories in the nature of firemen to light exemption shall preparation lye-boiler be availed of complementary only on the day work on which the plant is restarted after a closure. ii) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. iii) Intervals for food and rest shall be given to all workers allowed to work on such work. iv) provisions of rules 142 shall be compiled with. VII 1) Cloth 64(2) (b) work Work in the 51, 54 and provisions of printing in the nature of nature of 56 rules 142 shall factories or preparation preparatory or be compiled departments complementary complementary with. work to main operations of printing sanforizng, finishing and mercarsing of cloth. 2) Cotton 64(2) (b) work Work involved 51, 54 and provisions of 124 spinning and in the nature of in clearing 56 rules 142 shall weaving Mills. preparation blow room be compiled complementary flues. with. work 3) Film Studios 64(2) (b) work All work in the 51, 54 and provisions of in the nature of nature of the 56 rules 142 shall preparation preparatory or be compiled complementary complementary with. work work which is necessary for the shooting of files. VIII Dyeing or 64(2) (b) work Work 51, 54, 55 i) No worker beaching in the nature of performed by and 56 shall be required factories or preparation Kiermen or allowed to department. complementary work on shifts work of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) provisions of rules 142 shall be compiled with. IX. 1) Brick 64(2) (b) for Work of 55 i) No worker Factories. work which for Firemen on shall be required technical reason Kilns or allowed to must be carried work on shifts on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 2) Cashew Nut 64(2) (b) for Oil Extraction 55 i) No worker factories work which for work. shall be required technical reason or allowed to must be carried work on shifts on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 3) Cloth 64(2) (d) for Work of cloth 55 i) No worker Printing and work which for printing, shall be required 125 processing technical reason bleaching, factories. must be carried furnishing on mercerising, continuously. raising, dyeing, singeing and sanforizing. 4) Collapsible 64(2) (d) for Work of 55 tube work which for painting manufacturing technical reason coating, drying factories. must be carried of collapsible on tubes if carried continuously. on in a continuous process. 5) Cycle 64(2) (d) for Work of 55 manufacturing work which for painting and Automobile technical reason enamelling manufacturing must be carried section and and on service manufacturing continuously. automatic of Steel planting plant. furniture. 6) Enamelled 64(2) (d) for Work of 55 wire work which for enamelling of manufacturing technical reason wires. factories. must be carried on continuously. 7) Ferrous and 64(2) (d)for Work on Hot 55 Non-ferrous work which Rolling. metal factories. for technical reason must be carried on continuously. or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. i) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. i) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. i) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. i) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for 126 food and rest shall be given to all workers allowed to work on such work. 8) Flour Mills 64(2) (d) for All work. 55 i) No worker work which shall be required for technical or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 9) Gum 64(2) (d) for Work 55 i) No worker Industry work which performed in shall be required for technical connection or allowed to reason must be with sliting, work on shifts carried on dehusking, of longer than 8 continuously. grinding and hours duration. packing. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 10) India 64(2) (d)for Melting 55 i) No worker Government work which Department shall be required Mint. for technical including dress or allowed to reason must be washing. work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 11) Leather 64(2) (d)for Working of 55 i) No worker Cloth factories work which continuous shall be required for technical coating of PVC or allowed to reason must be drying, fusing work on shifts carried on in hot air oven of longer than 8 continuously. and embossing. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 127 12) Line 64(2) (d)for Workers 55 i) No worker Bhatties work which employed on shall be required for technical Bhatties. or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 13) Oil Mills. 64(2) (d)for All continuous 55 i) No worker work which process work. shall be required for technical or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 14) Ordnance 64(2) (d)for Work in 55 i) No worker factories work which melting shop shall be required for technical swarfaneal in or allowed to reason must be furnace gas work on shifts carried on producers, of longer than 8 continuously. electrical sub- hours duration. stations and ii) Intervals for water and food and rest electrical shall be given to distribution all workers departments. allowed to work on such work. 15) Pharmaceutical 64(2) (d)for All continuous 55 i) No worker work which process work. shall be required for technical or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 16) Plastic factories 64(2) (d)for Work on 55 i) No worker work which plastic injection shall be required for technical moulding or allowed to 128 reason must be machine and carried on extrusion continuously. machine. work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 17) Pottery works 64(2) (d)for Work of 55 i) No worker work which fireman on shall be required for technical kilns or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 18)Shellac 64(2) (d)for Workers 55 i) No worker factories. work which employed on shall be required for technical kilns. or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 19) Smelting and 64(2) (d)for 1) Work on the 55 i) No worker Refining factories. work which reducing shall be required for technical furnace. or allowed to reason must be 2) All work on shifts carried on continuous of longer than 8 continuously. process work in hours duration. connection ii) Intervals for with food and rest electrolytic shall be given to refining. all workers allowed to work on such work. 20) Soap factories. 64(2) (d)for Work on soap 55 i) No worker work which boiling pans shall be required for technical and soap or allowed to reason must be drying pans. work on shifts 129 carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. 21) Sodium and 64(2) (d)for All works 55 i) No worker potassium work which shall be required bicarbonate for technical or allowed to factories reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. i) No worker 22) Spinning and 64(2) (d)for Work on hot air 55 shall be required weaving Mills. work which sizing machine. or allowed to for technical work on shifts reason must be of longer than 8 carried on hours duration. continuously. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. X. 1) Acetylene 64(2) (d)for Generation of 51, 52, 54, i) No worker factories work which for gas and filling 55 and 56. shall be required technical reason of cylinders. or allowed to must be carried work on shifts on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker 130 2) Carbonic 64(2) (d)for Work of Acid gas works work which for firemen, technical reason pumpmen, must be carried plant driver, on oilers and the continuously. filling of cylinders. shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period 131 covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 3) Carbonic 64(2) (d)for 51, 52, 54, i) No worker Acid work which for All works 55 and 56. shall be required solidification technical reason except packing or allowed to works must be carried blocks. work on shifts on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under 132 section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 4) Cement 64(2) (d)for 51, 52, 54, i) No worker factories and work which All continuous 55 and 56. shall be required asbestos for technical process work. or allowed to cement reason must be work on shifts factories. carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has 133 failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 5) Chemical 64(2) (d)for 51, 52, 54, i) No worker factories. work which All continuous 55 and 56. shall be required for technical process work. or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work 134 the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 6) Chemical 64(2) (d)for 51, 52, 54, i) No worker Product work which Process of 55 and 56. shall be required factories. for technical manufacturing or allowed to reason must be activated work on shifts carried on carbon. of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that 135 next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 7) Cinematographic 64(2) (d)for 51, 52, 54, i) No worker films processing work which Work on 55 and 56. shall be required factories. for technical developing and or allowed to reason must be washing work on shifts carried on process. of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period 136 of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 8) Coal gas 64(2) (d)for 51, 52, 54, i) No worker factories work which All work in the 55 and 56. shall be required for technical retort house or allowed to reason must be and on the work on shifts carried on water gas plant. of longer than 8 continuously. Work of the hours duration. male yard ii) Intervals for labour staff in food and rest unloading coal, shall be given to feeding hopper all workers and removing allowed to work cake, work on on such work. the siphons, iii) Provisions boilers station of rules 142 metres and shall be governors. compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of 137 the shift to which he belongs. 9) Computer 64(2) (d)for 51, 52, 54, i) No worker installation. work which All works. 55 and 56. shall be required for technical or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 138 10) Confectionary 64(2) (d)for 51, 52, 54, i) No worker Manufacturing work which Manufacturing 55 and 56. shall be required Deptt. Of for technical of malted or allowed to factories. reason must be chocolate work on shifts carried on flavoured food of longer than 8 continuously. and chocolate hours duration. making. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 11) Crude 64(2) (d)for 51, 52, 54, i) No worker Mineral Oil & work which a) All 55 and 56. shall be required Petro-chemical for technical continuous or allowed to refining factory. reason must be process work work on shifts 139 carried on performed by of longer than 8 continuously. the plant hours duration. operators, fire ii) Intervals for operators food and rest laboratory shall be given to testers and all workers analysts, allowed to work maintenance on such work. and instrument iii) Provisions personnel of rules 142 connected with shall be continuous compiled with. process work, iv) Compliance dressers and with section 53 sample carriers. shall be made in b) Work such way that performed by such worker safety shall be allowed operators. not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 12) Dextrine 64(2) (d)for 51, 52, 54, i) No worker Manufacturing work which All continuous 55 and 56. shall be required factories. for technical process work. or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest 140 shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 13) Distilleries 64(2) (d)for 51, 52, 54, i) No worker work which Work on the 55 and 56. shall be required for technical extraction of or allowed to reason must be sugar from work on shifts carried on various bases, of longer than 8 continuously. fermentation of hours duration. sugar cane ii) Intervals for juice and food and rest distillation of shall be given to fermented all workers wash. allowed to work on such work. 141 14) Electrical 64(2) (d)for work which Operations in accumulators, for technical connection charging deptt. reason must be with charging Of factories. carried on electrical continuously. accumulators. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. 142 iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 15) Electrical 64(2) (e) for 51, 52, 54, i) No worker work which Operations & 55 and 56. shall be required receiving for technical maintenance of or allowed to Stations & Sub- reason must be transformers & work on shifts stations. carried on it auxiliaries of longer than 8 continuously. including hours duration. receiving and ii) Intervals for distribution, food and rest switchgears, shall be given to lightning all workers arrester, allowed to work synchronous on such work. and other iii) Provisions condensers and of rules 142 rotatory and shall be static compiled with. condensers. iv) Compliance with section 53 shall be made in such way that 143 such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 16) Electronic 64(2) (e) for 51, 52, 54, i) No worker work which Welding 55 and 56. shall be required components for technical lacquering and or allowed to factory reason must be colour work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in 144 each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 17) Ferrous and 64(2) (e) for 51, 52, 54, i) No worker work which Hot rolling 55 and 56. shall be required non-ferrous for technical or allowed to metal factories. reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory 145 holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 18) Glass 64(2) (e) for 51, 52, 54, i) No worker work which All continuous 55 and 56. shall be required factories for technical process work or allowed to reason must be including work on shifts carried on cartoning and of longer than 8 continuously. packing carried hours duration. out in ii) Intervals for continuous food and rest chain. shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a 146 worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 19) Glycerine 64(2) (e) for 51, 52, 54, i) No worker work which All continuous 55 and 56. shall be required factories for technical process work or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be 147 allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 20) Hydraulic 64(2) (e) for 51, 52, 54, i) No worker work which All work 55 and 56. shall be required pumping for technical or allowed to Stations. reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift 148 64(2) (e) for 21) Ice factories work which Work of the for technical engine and reason must be compressors carried on drivers and continuously. assistants and oilers. provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence 149 before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 22) Magnesium 64(2) (e) for 51, 52, 54, i) No worker work which The work on 55 and 56. shall be required Chloride for technical concentrating or allowed to Factories. reason must be process. work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified 150 stopping time of the shift to which he belongs. 64(2) (e) for 51, 52, 54, i) No worker 23) Milk Diaries work which All work of 55 and 56. shall be required for technical receiving or allowed to reason must be chilling process work on shifts carried on of milk by of longer than 8 continuously. pasturisation, hours duration. storage, storage ii) Intervals for bottling and food and rest packing of shall be given to milk. all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 151 24) Oil tank 64(2) (e) for 51, 52, 54, i) No worker work which a) Work 55 and 56. shall be required installations for technical performed by or allowed to reason must be workers in work on shifts carried on connection of longer than 8 continuously. with pumping hours duration. operations. ii) Intervals for b) Work food and rest performed by shall be given to furnacemen all workers and firemen. allowed to work c) Work on such work. performed by iii) Provisions safety of rules 142 operators. shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 25) Oxygen 64(2) (e) for 51, 52, 54, i) No worker work which Engine and 55 and 56. shall be required factories. for technical plant drives, or allowed to 152 reason must be oilers the carried on filling the continuously. cylinders. 26) Paper, card- 64(2) (e) for work which Work board and for technical performed on strawboard reason must be choppers factories. carried on digestor, continuously. kneeders, stainers, and work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for 153 washers, food and rest beaters, paper shall be given to making all workers machines, allowed to work pumping plants on such work. reelers and iii) Provisions cutters. of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 64(2) (e) for 51, 52, 54, i) No worker 27)Pharmaceutical work which All continuous 55 and 56. shall be required factories for technical process or allowed to reason must be operations in work on shifts carried on chemical of longer than 8 continuously. plants. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work 154 on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 64(2) (e) for 51, 52, 54, i) No worker 28) Phonograph work which Work 55 and 56. shall be required Disc manufacturing for technical performed in or allowed to factories reason must be matrix work on shifts carried on Department. of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be 155 compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 29) Potassium 64(2) (e) for 51, 52, 54, i) No worker work which Work in the 55 and 56. shall be required Chlorate for technical cell room. or allowed to factories. reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in 156 30) Public 64(2) (e) for work which Operation and electricity supply for technical maintenance of factories reason must be prime mover generating carried on and auxiliaries electricity in any continuously. generators, manner and those transformers engine rooms and and switch boiler gears, also departments engines and generating boilers and electricity in any their manner. auxiliaries. such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than 157 two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 31) Public 64(2) (d) for 51, 52, 54, i) No worker work which 55 and 56. shall be required pumping and for technical or allowed to compressor reason must be work on shifts stations. carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive 158 32) Rubber Tyre 64(2) (e) for 51, 52, 54, work which All work on 55 and 56. and Rubber for technical curing process factories. reason must be of rubber carried on continuously. statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. i) No worker shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the 159 absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 33) Silver 64(2) (d) for 51, 52, 54, i) No worker work which All work 55 and 56. shall be required refineries for technical or allowed to reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift 160 worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 34) Soap 64(2) (e) for 51, 52, 54, i) No worker work which a) All 55 and 56. shall be required factories. for technical continuous or allowed to reason must be process work in work on shifts carried on continuous of longer than 8 continuously. soap making hours duration. plants. ii) Intervals for b) All food and rest continuous shall be given to process work in all workers synthetic allowed to work detergent plants on such work. including iii) Provisions cartoning and of rules 142 packing carried shall be out in a compiled with. continuous iv) Compliance chain. with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the 161 35) Sodium and 64(2) (d) for work which Work in Potassium for technical furnace and bicarbonate reason must be crystallisers factories. carried on continuously. subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 51, 52, 54, i) No worker 55 and 56. shall be required or allowed to work on shifts of longer than 8 hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not 162 commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 36) Starch 64(2) (e) for 51, 52, 54, i) No worker work which All work 55 and 56. shall be required Factories. for technical except the or allowed to reason must be engineering work on shifts carried on Department of longer than 8 continuously. and workshops. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the 163 specified stopping time of the shift to which he belongs. 37) Sugar 64(2) (d) for 51, 52, 54, i) No worker work which Operations 55 and 56. shall be required Factories. for technical beginning with or allowed to reason must be receiving and work on shifts carried on weighment of of longer than 8 continuously. sugarcane and hours duration. ending with ii) Intervals for bagging of food and rest sugar. shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he 164 belongs. 38) Vegetable 64(2) (e) for 51, 52, 54, i) No worker work which The work, viz. 55 and 56. shall be required Oil for technical refining, or allowed to hydrogenation reason must be bleaching, work on shifts factories. carried on filtering, of longer than 8 continuously. generation in of hours duration. hydrogenating ii) Intervals for and deodorisng food and rest processes, also shall be given to compression of all workers oxygen and the allowed to work cylinder filling. on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. 39) Factories 64(2) (d) for 51, 52, 54, i) No worker work which All continuous 55 and 56. shall be required 165 having effluent for technical process work. or allowed to Treatment plant reason must be work on shifts carried on of longer than 8 continuously. hours duration. ii) Intervals for food and rest shall be given to all workers allowed to work on such work. iii) Provisions of rules 142 shall be compiled with. iv) Compliance with section 53 shall be made in such way that such worker shall be allowed not less than two holidays in each period covered by four consecutive statutory holidays under section 52(1). v) In the absence of a worker who has failed to report for duty a shift worker may be allowed to work the whole or part of the subsequent shift provided that next shift of that worker shall not commence before a period of 16 hours has elapsed after the specified stopping time of the shift to which he belongs. XI 1) All Cotton 64(2) (b) for Work 51, 52, 54, All the five ginning work in the performed by 55, 56 and conditions in factories. nature of Gin Fitters 61. X(i). Register or preparatory of Machines and Muster Roll complementar Oilers. required to be y work and maintained 166 64(2) (f) for under section 62 work carried shall show out during correctly full fixed seasons particulars of and section periods within 64(3) for which each such consequential worker may be exemption required to from section work; Entries in 61. the register or Muster roll shall be up-to-date. XII 1) Pottery woks 64 (2) (d) for Work 52 and 55 All the work of performed by conditions as in continuous Sin Fitters, VII nature. Machine and Oilers. XIII 1) Gur(Jaggery) 64 (2) (b) for All work 51, 54,55 All the Factories work in the an 56 conditions as in nature of VIII Preparatory or complimentary work and 64(2) XIV 1) News printing 64(2) (1) for a) All works on 51, 54, 55 a) No worker Process work in daily/ weekly and 56 shall be allowed printing of News papers to work for Newspaper more than 56 which is held hours in any up due to week. breakdown of b) No overtime machinery. shall be carried on except for two days prior to the date of publication of the weekly newspaper. c) The exemption under this entry shall be availed of only in that section of the press where there is breakdown of machinery and d) Intervals for food and rest shall be given to all workers allowed to work on such work. XV i) All factories 64(2) (K) for Workers 51,52, 54, All the work notified engaged in any 55 and 56 conditions as in by the state work which is X (1) except 167 Government noticed by the condition No. as work of state (V) National Government in importance. the Official Gazette, as work of National Importance. Explanation: - 1. The Following shall be considered to be urgent repairs: - a) repairs to any part of the machinery, plant or structure of a factory which are of such a nature that delay in their execution would involve danger to human life or safety or the stoppage of manufacturing process; b) breakdown repairs to the motive power, transmission or other essential plant of other factories, collieries, railways, dockyards, harbours, tramways, motor transport, gas electrical generating and transmission, pumping or similar essential or public utility services carried out in general engineering works and foundries and which are necessary to enable such concerns to maintain their main manufacturing process, production or services during normal working hours; c) repairs to deep-sea ships and repairs to commercial aircraft done in a factory which are essential to enable such ships or aircraft to leave port at proper time or continue their normal operations in a sea-worthy or air- worthy condition, as case may be; and d) repairs in connection with a charge of motive power, for example, from steam to electricity or vice versa, when such work cannot possibly be done without stoppage of the normal manufacturing process. 2) Periodical cleaning is not included in the terms “examining” or “repairing”. 168 Chapter VII Employment of Young Persons Rule Description 146 Exemption of Certain Adult Workers 147 The Register of Child Worker Prescribed under Sec 72(3) Rule 146. Notice of Periods of Work for Children The notice of periods of work for child workers shall be in Form 23. Prescribed under Sec 73(2) Rule 147. The Register of Child Worker The Register of Child Workers shall be in Form 24. This register shall be written up afresh each year and shall be preserved for a period of five years. 169 Chapter VIII Annual Leave with Wages Rule Description 148 Leave with Wages Register 149 Leave Book 150 Medical Certificate 151 Notice of Inspector of Involuntary Unemployment 152 Notice by Worker 153 Grant of Leave with Wages 154 Mode of Computation of Cash Value of Wages 155 Payment of wages if the Worker Dies 156 Notice to Inspector of Lay Off 157 Notice by Manager 158 Register to be maintained in case of Exemption under Section 84 159 Exemption of Certain Factories Chapter VIII Annual Leave with Wages Prescribed under Sec Rule 148. Leave with Wages Register 1) The manager shall keep a Register in Form 25 herein after called the Leave with Wages Register: Provided that if the Chief Inspector is of opinion that any muster roll or register maintained as part of the routine of the factory, or return made by the manager, gives in respect of any or all of the workers in the factory, the particulars required for the enforcement of Chapter VIII of the Act, he may, by order in writing, corresponding extent, be maintained in place of and be treated as the register or return required under this Rule in respect of that factory. 2) Leave with Wages Register shall be preserved for a period a period of five years after the last entry in it and shall be produced before the Inspector on demand. Rule 149. Leave Book 1) The manager shall provide each worker who has become entitled to leave during calendar year, with a book in Form 26 (hereinafter called the leave book) not later than 31st January of the following year. The leave book shall be the property of the worker and the manager or his agent shall not demand it, except to make entries of the dates of holidays or interruptions in service, and shall not keep it for more than a week at a time: Provided that, in case of a worker who is discharged or dismissed from service during the course of the year, i.e. who is covered by subsection (3) of sec 79 of the Act, the manager shall issue an abstract from the “Register of Leave with Wages” ( Form 25) within a week from the date of discharge pr dismissal as the case may be. 2) If a worker loses his leave Book, the manager shall provide him with another copy on payment of fifty paise within fifteen days, and shall complete it from his record. Rule 150. Medical Certificate 170 If any worker is absent from work due to his illness and he wants to avail himself of the leave with wages due to him to cover the period of illness as provided under sub-section (7) of Section 79, he shall, if so required by the manager produce a medical certificate signed by a registered medical practitioner or by a registered or recognised Vaid or Hakim stating the cause of the absence and the period for which the worker is, in the opinion of such medical practitioner, Vaid or Hakim, unable to attend to his work. Rule 151. Notice of Inspector of Involuntary Unemployment The manager shall give, as soon as possible, a notice to the Inspector of every case of involuntary unemployment of workers, giving numbers of unemployed and the reasons for their unemployment. Entries to this effect shall be made in the register of leave with wages and the leave book in respect of each worker concerned. Rule 152. Notice by Worker Before or end of the calendar year, a worker may give notice to the manager of his intention not to avail himself of the leave with wages due during the following calendar year. The manager shall make an entry to that effect in the leave with wages register and in the leave book of the worker concerned. Rule 153. Grant of Leave with Wages 1) Whenever leave with wages is given to any worker, necessary entries shall be made in the leave with wages register and the leave book of the worker concerned. 2) As far as circumstances permit, members of the same family comprising husband, wife and children shall be allowed leave at the same time. 3) A worker may exchange the period of his leave with another workers subject to the approval of the manager. Rule 154. Mode of Computation of Cash Value of Wages 1) The cash equivalent of the advantage accruing through the concessional sale of food grains and other articles payable to workers proceeding on leave shall be the difference between the value of the average market rate prevailing during the month immediately preceding his leave and the value at the concessional rates allowed of foodgrains and other article he is entitled to. 2) For the purpose of the cash equivalent, monthly average marker rate of food grains and other articles shall be computed at the end of every month. Rule 155. Payment of wages if the Worker Dies If a worker dies before he resumes work, the balance of his pay, due for the period of leave, shall be paid to his nominee within the week of the receipt of intimation of death of the worker. For this purpose each worker shall submit a nomination in Form 27 duly signed by himself and attested by two witness. The nomination shall remain in force until it is cancelled or revised by another nomination. Rule 156. Notice to Inspector of Lay Off The manager shall give, as soon as possible, a notice to the Inspector of every case of lay off of workers by agreement or contract or as permissible under the standing orders, giving the number of such workers and the reasons for the lay off. Entries to this effect shall be made in the leave with wages register and the leave book in respect of each worker concerned. Rule 157. Notice by Manager 171 The manager shall cause a notice to be displayed giving the names of all workers whose leave, which has been carried forward has reached the maximum limit allowed under the first proviso to subsection (5) of section 79, as soon as possible in the first quarter of each calendar year the notice shall state that no further leave carried forward and that application for leave shall be made with one month from the date of the notice. A copy of the notice shall be given to each worker concerned. A copy shall also be delivered at the office of the Inspector. Rule 158. Register to be maintained in case of Exemption under Section 84 1) Where an exemption is granted under Section 84, the manager shall maintain a register showing the position of each worker as regard leave due, leave taken and wages granted. 2) He shall display at the main entrance of the factory, a notice giving full details of the system established in the factory for leave with wages and send a copy of it to the Inspector. 3) No alteration shall be made in the scheme approved by the State Government at the time of granting exemption under section 84 without its previous sanction. Rule 159. Exemption of Certain Factories The Chief Inspector may grant exemption from all or any of the provisions of Rule 153 to 162 in respect of all or any of the workers in any factory subject to such conditions as he may impose. 172 Chapter IX SPECIAL PROVISION Rules Description Rule 160 Dangerous operation Schedule I Manufacture of aerated water and processes incidental thereto Schedule II Electrolytic plating or oxidation of metal articles Schedule III Manufacture and repair of electric accumulators Schedule IV Glass Manufactures Schedule V Grinding or Glazing of materials and processes incidental thereto Schedule VI Manufacture and treatment or lead and certain lead Compounds of Lead Schedule VII Generation of gas from Dangerous Petroleum as defined in the Petroleum Act, 1934 Schedule VIII Cleaning or smoothening, roughening etc of articles Schedule IX Liming and tanning of raw hides and skins and processes incidental thereto Schedule X Manufacture of chromic acid or manufacture or recovery of the bichromate of sodium potassium or ammonium Schedule XI Manufacture or manipulation of Nitro or Amino compounds Schedule XII Handling and manipulation of corrosive substances. Schedule XIII Manufacturing of bangles and other articles from cinematograph film and toxic inflammable solvents Schedule XIV Processes involving manufacture, use or evolution or carbon disulphide and hydrogen sulphide Schedule XV Manufacture and manipulation of dangerous pesticides Schedule XVI Compression of Oxygen and Hydrogen Produced by Electrolytic Process or by Steam iron process. Schedule XVII Handling and processing of Asbestos, Manufacture of any Article of Asbestos and any other process of manufacture or otherwise in which Asbestos is used in any form. Schedule XVIII Manufacture or Manipulation of Manganese and its Compound Schedule XIX Carbon di-Sulphide Plants Schedule XX Benzene Schedule XXI Process of extracting oils, wax and fats from vegetable and animal sources in Solvent Extraction Plants Schedule XXII Manufacture or Manipulation of Carcinogenic Dye Intermediates Schedule XXIII Highly Flammable Liquids and Flammable compressed Gases Schedule XXIV Operations involving High Noise Level Schedule XXV Manufacture and manipulation of dangerous pesticides 173 Schedule XXVI Manipulation of stone or any other material containing free silica Schedule XXVII Fire Works Manufacture and Match Factories Schedule Composing, Printing, Binding and Processes and/or XXVIII Operations incidental thereto Schedule XXIX Processing of Cashew nut Schedule XXX Printing presses and type foundries and certain lead processes carried therein Schedule XXXI Manufacture of pottery Schedule XXXII Operation in Foundry Rule 161 Notification of accidents or dangerous occurrences Rule 162 Notice of Poisoning or Disease Rule 163 Procedures in appeals Rule 164 Display of notices Rule 165 Returns Rule 166 Service of notices Rule 167 Information required by the Inspector Rule 168 Registers/records to be produced on demand to the Inspector. Rule 169 Permissible levels of certain chemical substances in work environment Rule 170 Muster roll Rule 171 Register of accidents and dangerous occurrences Rule 172 Maintenance of inspection book: Rule 173 Information regarding closure of factories Rule 174 Power to Cancel the Licence and Registration upon receipt of report: Rule 175 Preservation of Records Rule 176 Manner of Destruction for Records Rule 177 Language in the Registers and records Rule 178 Exhibition of Name Board Rule 179 Power of Exemption Rules prescribed under Section 87 Rule 160. Dangerous operation 1) The following operations when carried on in any factory are declared to be dangerous operations under Section 87 1) Manufacture of aerated water and processes incidental thereto. 2) Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. 3) Manufacture and repair of electric accumulators. 4) Glass manufacture. 5) Grinding or glazing or metals. 174 6) Manufacture and treatment of lead and certain compounds of lead. 7) Generation of gas from dangerous petroleum as defined in clause (b) of section 2 of the Petroleum Act, 1934. 8) Cleaning or smoothing of articles by a jet of sand, metal shot or grit or other abrasive propelled by a blast of compressed air or steam. 9) Liming and tanning of raw hides and skins and processes incidental thereto. 10) Manufacture of chromic acid or manufacture or recovery of the bicromate of sodium, potassium or ammonium. 11) Manufacture or manipulation of nitro or amino compounds. 12) Handling and manipulation of corrosive substances. 13) Manufacture of bangles and other articles from cinematograph film and toxic and inflammable solvents. 14) Process involving manufacture use or evolution of carbon disulphate and hydrogen sulphide. 15) Manufacture and manipulation of dangerous pesticides. 16) Compression of oxygen and hydrogen produced by electrolytic. 17) Manufacture and manipulation of asbestos. 18) Manufacture and manipulation of manganese and its compounds. 19) Carbon-di-sulphide plants. 20) Benzene. 21) Process of extracting oils, wax and fats from vegetable and animal sources in Solvent Extraction Plant. 22) Manufacture or manipulation of Carcinogenic Dye Intermediates. 23) Highly Flammable liquids and Flammable compressed Gases 24) Operations Involving High Noise levels. 25) Chemical Involving High Noise Levels. 26) Manipulation of Stone or any other Material containing free Silica. 27) Fire Works factories and Match Factories. 28) Composting, Printing, Binding and Processes and/or Operations Incidental thereto. 29) Processing of Cashew nut 30) Printing process and type foundries and certain lead processes carried therein. 31) Manufacture of Pottery. 32) Operation in Foundries. 2) The provision specified in the Schedules annexed hereto shall apply to any class or description of factories wherein dangerous operations specified in each Schedule are carried. 3) “First Employment” means employment for the first time in a hazardous process or operation so notified under Section 87, or reemployment therein after cessation of employment in such process or operation for a period exceeding 3 (three) calendar months. 4) a) For the medical examination of workers to be carried out by the certifying surgeon as required by the schedule annexed to this rule, the occupier of 175 the factory shall pay fees at the rate of Rs. 25/- per examination of each worker every time he is examined. b) The fees prescribed in sub-rule (4) (a) shall be exclusive of any charges for biological, radiological or other tests which may have to be carried out in connection with the medical examinations. Such charges shall be paid by the occupier. c) The fees to be paid for medical examination shall be paid under head of account “0230 Labour & Employments – 104 - fees realised under the Factories Act” and submit original treasury challan to the office of the respective Inspector of factories. 5) Notwithstanding the provision specified in the schedule annexed to this Rule, the Inspector may by issue of orders in writing to the manager or occupier or both, direct them to carry out such measures, and within such time, as may be specified in such order with a view to removing conditions dangerous to the health of the workers, or to suspend any process, where such process constitutes, in the opinion of the Inspector, imminent danger of poisoning or toxicity. 6) Any register or record of medical examinations and tests connected therewith required to be carried out under any of the schedules annexed hereto in respect of any worker shall be kept readily available to the Inspector and shall be preserved till the expiry of one year after the worker ceases to be in employment of the factory. Schedule I Manufacture of aerated of water and processes incidental thereto 1) Fencing of machines – All machines for filling bottles or siphons shall be so constructed, placed or fenced as to prevent, as far as may be practicable, a fragment of a bursting bottle or siphon from striking any person employed in the factory. 2) Face guards and gauntlet - 1) The occupier shall provide and maintain in good condition for the use of all person engaged in filling bottles or siphon – a) suitable face-guards to protect the face, neck and throat, and b) suitable gauntlets for both arms to protect the whole hand and arms; Provided that i) paragraph 2(1) shall not apply where bottles are filled by means of an automatic machine so constructed that no fragment of a bursting bottle can escape, and ii) where a machine is so constructed that only one arm on the bottle at work upon ir is exposed to danger, a gauntlet need not be provided for the arm which is not exposed to danger. 3) The occupier shall provide and maintain in good condition for the use of all persons engaged in corking, crowning, and screwing, wiring, foiling, capsuling, sighting or labelling bottles or siphon - a) suitable face-guards to protect the face, neck and throat, and b) suitable gauntlets for both arms to protect the arms and at least half of the palm and the space between the thumb and forefinger. 176 4) Wearing of face guards and gauntlets – All persons engaged in any of the processes specified in paragraph 2 of this schedule shall, at work in such process, wear the face-guards and gauntlets provided under the provisions of the said paragraph. Schedule II Electrolytic plating or oxidation of metal articles by use of an electrolytes containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. 1) Definitions: - For the purpose of this schedule – a) “Electrolytic process” means the electrolytic planting or oxidation of metal article by the use of an electrolyte containing acids, bases or salts of metal such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. b) “Bath” means any vessel used for an electrolytic chromium process or for any subsequent process, c) “Employed” means any process involving contact with liquid from a bath. d) “Suspension” means suspension from employment in any process involving contract with liquid from any bath by written certificates in the Health Register, signed by the certifying surgeon, who shall have power of suspension as regards all persons employed in any such process. 2) Exhaust draught: -An efficient exhaust draught shall be applied to every vessel in which an electrolytic process is carried on. Such draught shall be provided by mechanical means and operate on the vapour or spray given off in the process as near as may be at the point of origin. The exhaust draught appliance shall be so constructed, arranged and maintained as to prevent the vapour or spray entering into any room or place in which work is carried on. 3) Prohibition relating to women and young persons: - No woman, adolescent or child shall be employed or permitted to work at a bath. 4) Floor of work rooms: - The floor of every room containing a bath shall be impervious to water. The floor shall be maintained in good and level condition and shall be washed down at least once a day. 5) Protective clothing: - 1) The occupier of the factory shall provide and maintain in good and clean condition the following articles of protective clothing for the use or all persons employed on any process at which they are liable to come in contact with liquid from a bath and such clothing shall be worn by the person concerned: - a) water-proof aprons and bibs, and b) for persons actually working at bath, loose-fitting rubber gloves and rubber boots or other water-proof footwear and chemical goggles. 2) The occupier shall provide and maintain for the use of all persons employed suitable accommodation for the storage and adequate arrangements for the drying of the protective clothing. 6) Medical requisites: - The occupier shall provide and maintain a sufficient supply of suitable ointment and impermeable water-proof plaster in a separate box readily 177 accessible to the workers and used solely for the purpose of keeping the ointments and plaster. 7) Medical Examination: - 1) Every person employed in electrolytic process, shall be examined by a certifying surgeon within 30 days of his first employment in the said process and if found fit, shall be granted by the certifying surgeon a certificate of fitness in Form 28. Such examination shall include X-ray of the chest and - a) in case of chromium plating include examination for nasal septum perforation and test for chromium in urine; b) in case of nickel plating, test for nickel in urine; and c) in case of cadmium plating, test for cadmium in urine and micro globulin in urine. 2) No worker shall be employed in any electrolytic process unless certified fit for such employment by the Certifying Surgeon. 3) Every worker employed in the electrolytic process shall be re-examined by a Certifying Surgeon at least once in every year, except in case of the workers employed in cadmium, chromium and nickel plating processes for whom this examination shall be carried out once in every six months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified under sub-paragraph 1 excluding the X-ray of the chest which shall not be required normally to be carried out earlier than once in three years. 4) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 28. The record of examination and re-examinations carried out shall be kept in the custody of the manager of the factory. The record of each examination carried out including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 5) The certificate of fitness and the health register shall be kept readily available for inspection by the Inspector. 6) If at any time the Certifying Surgeon is of the opinion that a worker is no longer for employment in the electrolytic process on the ground that continuance therein would involve danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of the his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person declared unfit in such circumstances shall be provided with alternate placement facility unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitate. 7) No person who has been found unfit to work as said sub-paragraphs (6) shall be re-employed or permitted to work in the said process unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 8) Chief Inspector of Factories is of the opinion that conditions of work in the said process are unsatisfactory, he may, by order in writing, require the manager of the factory to have the person employed in the said process medically examined by a certifying surgeon at more frequent intervals. 178 8) Cautionary placard: - A cautionary placard in the form specified below and printed in the language of the majority of the workers employed shall be affixed in a prominent place in the factory where it can be easily and conveniently read by the workers. Cautionary Notice Electrolyting process 1) Chemicals handled in this plant are corrosive and poisonous. 2) Smoking, chewing tobacco, eating food or drinking, in this area is prohibited. No food stuff or drink shall be brought in this area. 3) Some of these chemicals may be absorbed through the skin and may cause poisoning. 4) A good wash shall be taken before meals. 5) Protective devices supplied shall be used while working in this area. 6) Spillage of the chemicals on any part of the body or on the floor shall be immediately washed away with water. 7) All workers shall report for the prescribed medical tests regularly to protect their own health. 8) Weekly examination: - a) The occupier of every factory shall appoint a qualified medical practitioner, whose appointment shall be subject to confirmation by the Chief Inspector. b) No person shall be employed in electrolytic process unless he has been examined and found fit for employment in the said process by the qualified medical practitioner. Such examination shall include inspection of hands, forearms and nose and will be carried out at intervals, of not more than one week. The results of such examination shall be maintained in a Health Register in Form 29. The register shall be kept by the manager and shall contain the names of all the persons employed in the said process and the certificate of fitness in respect of each person issued by the certifying surgeon and the certificates shall be attached thereto. c) If at any time, the registered medical practitioner is of opinion that nay person is no longer fit for employment in the electrolytic process, he shall make a record of his findings in the health register and intimate the manager in writing that the said person is unfit for work in the said process. d) A person so found unfit by the registered medical practitioner shall be sent by the manager to the certifying surgeon with report from the registered medical practitioner. The certifying Surgeon, after examination may suspend the said person from working in the said process. No person, after suspension shall be employed without written sanction from the certifying surgeon nor his name entered in or the certificate attached to the health register. 9) Water facilities: 1) There shall provided and maintained in good repairs for the use of all persons employed in electrolytic process and processes incidental to it – a) a wash place under cover, with either – 179 i) a through with a smooth impervious surface filled with a waste pipe, and of sufficient length to allow at least 60 cms for every 5 persons employed at any one time, and having a constant supply of water from taps or jets above the trough at interval of not more than 60 cms., or ii) at least one wash basin for every five such persons employed at one time, fitted with a waste pipe and having a constant supply of water laid on. b) a sufficient supply of clean towels renewed daily, and soap or other suitable cleaning material. 2) In addition to the facility in sub-paragraphs (1), an approved type of emergency shower with eye fountain shall be provided and maintained in good working order. Whenever necessary, in order to ensure continuous water supply, storage tank of 1500 litres capacity shall be provided as a source of clean water for emergency use. Schedule III Manufacture and Repair of Electric Accumulators 1) Savings: - This schedule shall not apply to the manufacture or repair of electric accumulators or parts thereof not containing lead or any compound of lead, or to the repair on the premises, of any accumulator forming part of a stationary battery. 2) Definitions: - For the purposes of this schedule - a) “Lead process” means the melting of lead or any material containing lead casting, pasting, lead burning, or any other work, including trimming or any other abrading or cutting of pasted plates, involving the use, movement or manipulation of, contact with any oxide of lead. b) “Manipulation of raw oxide of lead” means any lead process involving any manipulation or movement of raw oxides of lead other than its conveyance in a receptacle or by means of an implement from one operation to another. c) “Suspension” means suspension form employment in any lead process by writing certificates in the Health Register, From 29 signed by the Certifying Surgeon, who shall have power of suspension as regards all persons employed in any such process. 3) Prohibition relating to women and young persons: - No women or young person shall be employed or permitted to work in any lead or pasting is carried on. 4) Separation of certain processes: - Each of the following process shall be carried on in such a manner and under such conditions as to secure effectual separation from one another and other process: - a) Manipulation of raw oxide of lead. b) Pasting; c) Drying of pasted plates; d) For with lead burning (“tacking”) necessary carried on in connection therewith; e) Melting down or pasted plates; f) The grid casting shop. 180 5) Air Space: - In every room in which a lead process is carried on, there shall be at least 15 cubic metres of air for each person employed therein, and in computing this air space no height over 3.5 metres shall be taken into account. 6) Ventilation: - Every workroom shall be provided with inlets and outlets of adequate size as to secure and maintain efficient ventilation in all parts of the room. 7) Distance between workers in pasting room: - In every pasting room the distance between centre of the working position of any plaster and that of the plaster working nearest to him shall not be less than 150 centimetres. 8) Floor of work-rooms: - 1) The floor of every room in which a lead process in carried on shall be– a) of cement or similar material so as to be smooth and impervious to water; b) maintain in sound condition; c) kept free from material, plant, or other obstruction not required for, or produced in, the process carried on in the room. 2) In all such rooms other than grid casting shops the floor shall be – d) cleansed daily after being thoroughly sprayed with water at a time when no other work is being carried on in the room. 3) In grid casting shops the floor shall be cleaned daily. 4) Without prejudice to the requirements of sub-paragraphs (1), (2) and (3) where manipulation of raw oxide of lead or pasting in carried on, the floor shall also be – a) kept constantly moist while work is being done; b) provided with suitable and adequate arrangements for drainage; c) thoroughly washed daily by means of a hose pipe. 9) Work-benches: - The work-benches at which any lead process is carried on shall: - a) have a smooth surface and be maintained in sound condition; b) be kept free from all materials or plant not required for a produced in, the process carried on thereat; and all such work-benches other than those in grid casting shops shall – c) be cleaned daily either after being a thoroughly damped or by means of a suction cleaning apparatus at a time when no other work is being carried on thereat; and, all such work-benches in grid casting shops shall – d) be cleansed daily; and every work bench used for pasting shall- e) be covered throughout with sheet lead or other impervious material; f) be provided with raised edges; g) be kept constantly moist while pasting is being carried on; and every work-bench used for trimming, brushing, filing or any other abrading or cutting or pasting containing water. h) be fitted with a top having opening or grill which shall allow any clippings, filling, or dust produced to fall into a collecting trough containing water. 181 10) Exhaust draught: - The following processes shall not be carried on without the use of efficient exhaust draught: - a) Melting of lead or materials lead; b) Manipulation of raw oxide of lead, unless done in an enclosed apparatus so as to prevent the escape of dust into the work-room; c) Pasting; d) Trimming, brushing, filing or any other abrading or cutting of pasted plates giving rise to dust; e) Lead burning other than - i) “tacking” in the formation room; ii) chemical burning for the making of lead linings for cell cases necessarily carried on in such a manner that the application of efficient exhaust is impracticable. Such exhaust draught shall be effected mechanical means and shall operate on the dust or fume given off as nearly as may be at its point of origin, so as to prevent it from entering the air of any room in which persons work. 11) Fumes and gases from melting pots: - The products of combustion produced in the heating of any melting pot shall not be a allowed to escape into a room in which persons work. 12) Container for dross: - A suitable receptacle with tightly fitting cover shall be provided and used for dross as it is removed from every melting pt. Such receptacle shall be kept covered while in the work room, except when dross is being deposited therein. 13) Container for lead waste: - A suitable receptacle shall be provided in every work- room in which old plates and waste material which may give rise to dust shall be deposited. 14) Racks and shelves in drying room: - The racks or shelves provided in any drying room shall not be more than 240 centimetres from the floor not more than 60 centimetres in width; provided that as regards racks or selves set or drawn from both sides, the total width shall not exceed 12 centimetres. Such racks or selves shall be cleaned only after being thoroughly damped unless an efficient suction cleaning apparatus is used for this purpose. 15) Medical examination: - a) Every person employed in a lead process shall be examined by the Certifying Surgeon within seven days preceding or following the date of his first employment in such process and thereafter shall be examined by the Certifying Surgeon once in every calendar month, or at such other intervals as may be specified in writing by the Chief Inspector, on a day of which the notice shall be given to all concerned. “First employment” means first employment in a lead process in the factory or workshop and also re-employment therein in a lead process following any cessation of employment in such process for a period exceeding three calendar months. b) A Health Register in Form 29 containing the names of all persons employed in a lead process shall be kept. c) No person after suspension shall be employed in a lead process without written sanction from the Certifying Surgeon entered in or attached to the Health Register. 182 15-A. Medical Facilities: - 1) The occupier of the factory shall appoint at least a part-time qualified medical practitioner, possessing MBBS degree and having a post-graduate Diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner so appointed shall be required to put in minimum four hours attendance on every working day in the ambulance room for carrying out the duties specified in the following sub-paragraph (2). Provided that, in cases of factories employing less than 500 workers per day, the Chief Inspector of factories may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) The medical practitioner, so appointed, shall perform the following duties that is to say – a) to maintain health Register in Form 29. b) to undertake medical supervision of persons engaged on dangerous operations specified in Rule 165 of these rules; c) to look after health, education and rehabilitation of sick, injured or affected workers. d) to carry out inspection of work-rooms where dangerous operation are carried out and to advise the management in respect of the measures to be adopted for protection of workers involved therein. 3) For the purpose of medical supervision by the medical practitioner so appointed, the occupier shall provide for the former’s exclusive use at the factory premises a room which shall be properly cleaned, adequately lighted, ventilated and furnished with a screen, a table and office stationery, chairs and other facilities and instruments including X-raying arrangement for schedules IV, X, XVII for such examinations and such other equipments as may be prescribed by the Chief Inspector of Factories from time to time. 16) Protective clothing: - Protective clothing shall be provided and maintained in good repair for all persons employed in – a) manipulation of raw oxide of lead; b) pasting; c) the formation room; and such clothing shall be worn by the persons concerned. The protective clothing shall consist of a water-proof apron and manipulation of raw oxide of lead or in pasting head covering. The head coverings shall be washed daily. 17) Mess-room: - There shall be provided and maintained for the use of all persons employed in a lead process and remaining on the premises during the meal intervals, a suitable mess-room, which shall be furnished with (a) sufficient tables and benches, and (b) adequate means for warming food, 18) Cloak-room: - There shall be provided and maintained for the use of all persons employed in a lead process: - a) a cloak-room for clothing put off during work hours with adequate arrangement, for drying the clothing if wet. Such accommodation shall be separate from any mess-room; b) separate and suitable arrangements for the storage of protective clothing provided under paragraph 16. 183 19) Washing facilities: - There shall be provided and maintained in a cleanly state and in good repair for the use of persons employed in a lead process – a) a wash-place under cover, with either – i) trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow of atleast 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from tape or jets above the trough at intervals of not more than 60 centimetres; or ii) a sufficient supply of clean towels made of suitable material renewed daily, which supply, in the case of pasters and persons employed in the manipulation of raw oxide of lead, shall include a separate marked towel for each workers; and iii) a sufficient supply of soap or other suitable cleansing material and of nailbrushes. b) There shall, I addition, he provided means of washing in close proximity to the rooms in which manipulation of raw oxide of lead or pasting carried on if required by notice in writing from the Chief Inspector. 20) Time to be allowed for washing: - Before each meal and before the end of the day’s work at least 10 minutes, in addition to the regular meal time off shall be allowed for washing to each person who has been employed in the manipulation of raw oxide of lead or in pasting; provided that if there be one basin or 60 centimetres of trough for each such person this rule shall not apply. 21) Facilities for bathing: - Sufficient bath accommodation to the satisfaction of the Chief Inspector shall be provided for all persons engaged in the manipulation of raw oxide of lead or in pasting, and a sufficient supply of soap and clean towels. 22) Foods, drinks etc. prohibited in workrooms: - No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any work-room on. 23) Storage of lead oxides: - All bags containing or having contained oxide of lead shall be kept in a closed room used only for this purpose. 24) Re-use of paper or cloth restricted: - a) Paper once used for backing or drying pasted plates shall not be use again in the factory. b) Cloth once used for baking or drying pasted plates shall not be stored or handled unless it is moist so as not to give off dust. Schedule IV Glass Manufactures 1) Exemption: - If the Chief Inspector is satisfied in respect of any factory or any class or process that, owing to the special methods of work or the special conditions in a factory or otherwise, any of the requirements of this Schedule can be suspended or relaxed without danger to the persons employed therein or that the application of this schedule or any part thereof is for any reason, impracticable, he may by certificate in writing authorise such suspension or relaxation as may be indicated in the certificate for such period and on such conditions as he may think fit. 2) Definitions: - For the purpose of this Schedule – 184 a) “Efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fumes so as to prevent them (as far as practicable) under the atmospheric conditions usually prevailing from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fume or dust originate; b) “Lead Compound” means any compound of lead other than galena which, when treated in the manner described below, yields to an aqueous solution of hydrochloric acid a quantity of soluble lead compound exceeding when calculated as lead monoxide, five percent of the dry weight of the portion taken for analysis. The method of treatment shall be as follows: - A weighed quality of the material which has been dried at 100oC and thoroughly mixed shall be continuously shaken for one hour, at the common temperature with 1,000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filtrate, shall then be precipitated as lead sulphide and weighed as lead sulphate. c) “Suspension” means suspension from employment in any process specified in paragraph 3 by written certificate in the Health Register in Form 7 signed by the Certifying Surgeon who shall have power of suspension as regards all persons employed in any such process. 3) Exhaust draught: - The following processes shall not be carried on except under an efficient exhaust draught or under such other conditions as may be approved by the Chief Inspector: - a) The mixing of raw materials to form a “bath”. b) The dry grinding, glazing and polishing of glass or any article of glass; c) All processes in which hydrofluoric acid fumes or ammoniacal vapours are given off; d) All processes in the making of furnace moulds or “pots” including the grinding or crushing of used “pots”; e) All processes involving the use of a dry lead compound. 4) Prohibition relating to women and young persons: - No woman or young person shall be employed or permitted to work in any of the operations specified in paragraph 3 or at any place where such operations are carried on. 5) Floor and work-benches: - The floor and work-benches of every room in which a dry compound of lead is manipulated or in which any process is carried on giving off silica dust shall be kept moist and shall comply with the following requirements: - The floors shall be – a) of cement or similar materials so as to be smooth and impervious to water. b) maintained in sound conditions; and c) cleaned daily after being thoroughly sprayed with water at a time when no other work is being carried on in the room The work-benches shall: - a) have a smooth surface and be maintained in sound conditions; and 185 b) be cleaned daily either being thoroughly damped or by means of a suction cleaning apparatus at a time when no other work is being carried on thereat 6) Use of hydrofluoric acid: - The following provisions shall apply to rooms in which glass is treated with hydrofluoric acid: - a) There shall be inlets and outlets of adequate size so as to secure and maintain efficient ventilation in all parts of the rooms; b) The floor shall be covered with gutta-percha and be tight and shall slope gently down to a covered drain; c) The work-places shall be so enclosed in projecting holes that opening required for bringing in the objects to be created shall be as small as practicable; and d) The efficient exhaust draught shall be so contrived that the gases are exhausted downwards. 7) Storage and transport or hydrofluoric acid: - Hydrofluoric acid shall not be stored or transported except in cylinders or receptacles made of lead or gutta-percha. 8) Blow-pipes: - Suitable facilities shall be readily available for sterilizing the blowpipes used by the glass-blowers and such blow-pipes shall be sterilized at the beginning of the operation of blowing, each day. 9) Food, drinks, etc., prohibited in work-room: - No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any room or work place wherein any process specified in paragraph 3 is carried on. 10) Protective clothing: - The occupier shall provide, maintain in good repair and keep in a clean condition for the use of all persons employed in the processes specified in paragraph 3 suitable protective clothing, footwear, and goggles according to the nature of the work and such clothing, footwear, etc, shall be worn by the persons concerned. 11. Washing facilities: - There shall be provided and maintained in a cleanly state and in good repair for the use of all persons employed in the processes specified in paragraph 3 – a) a wash-place with either – i) a trough with a smooth impervious surface fitted with a waste pipe without plug and of sufficient length to allow of at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at interval of not more than 60 centimetres; or ii) at least one wash basin for every five such persons employed at any one time fitted with a waste pipe and plug and having an adequate supply of water laid on or always readily available; and a sufficient supply or clean towels made of suitable materials renewed duly with a sufficient supply of soap or other suitable cleaning material and of nail brushes; and a sufficient number of stand pipes with taps – the number and location of such stand pipes shall be to he satisfaction of the Chief Inspector. 12) Medical examination: - 186 a) Every person employed in any process specified in paragraph 3 shall be examined by the Certifying Surgeon, within seven days preceeding or following the date of his first employment in such process and thereafter shall be examined by the Certifying Surgeon once in every calendar month or at such other intervals as may be specified in writing by the Chief Inspector on a day of which due notice shall be given to all concerned. b) A Health Register in Form 29 containing the names of all persons employed in any process specified in paragraph 3 shall be kept. c) No person after suspension shall be employed in any process specified in paragraph 3 without written sanction from the Certifying Surgeon entered in or attached to the Health Register. 13. Medical facilities: - 1) The occupier of the factory shall appoint at least a part time qualified medical practitioner, possessing MBBS degree and having post-graduate diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner so appointed shall be required to put in minimum four hours attendance on every working day in the ambulance room for carrying out the duties specified in the following sub-paragraph (2) Provided that, in cases of factories employing less than 500 workers per day, the Chief Inspector of Factories may allow attendance for shorter duration taking into consideration all the relevant facts of each case. 2) The medical practitioner so appointed, shall perform the following duties that is to say: - a) to maintain Health Register in Form 29. b) to undertake medical supervision of persons engaged on dangerous operations are carried out and to advice the management in respect of the measures to be adopted for protection of health of the workers involved therein. c) to look after health , education and rehabilitation of sick, injured or affected workers; d) to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management in respect of the measures to be adopted for protection of health of the workers involved therein. 3) For the purpose of medical supervision by the medical practitioner so appointed, the occupier shall provide for the former’s exclusive use at the factory premises a room which shall be properly cleaned, adequately lightened, ventilated and furnished with a screen, a table with office stationary, chairs and other facilities and instrument including X-ray arrangements also for Schedule X and XVII for such examinations and such other equipments as may be prescribed by the Chief Inspector from time to time. Schedule V Grinding or Glazing of materials and processes incidental thereto 1. Definitions: - For the purpose of this schedule: - a) “Grindstone” means a grindstone composed of natural or manufactured stand stone but does not include a metal wheel or cylinder into which blocks of natural or manufactured sandstone are fitted. 187 b) “Abrasive wheel” means a wheel manufactured of blended emery or similar abrasive. c) “Grinding” means the abrasion, by aid of mechanical power, of metal, by means of grindstone or abrasive wheel. d) “Glazing” means the abrading, polishing or finishing by aid or mechanical power of metal, by means of any wheel, buff, mop or similar appliance to which any abrading or polishing substance is attached or applied. e) “Racing means turning up, cutting or dressing or a revolving grindstone before it is brought into use for the first time. f) “Hacking” means the chipping of the surface of revolving grindstone by the application of a rod, bar or strip of metal to such surface. g) “Rodding” means the dressing of the surface of a revolving grindstone by the application of a rod, bar or strip of metal to such surface. 2) Exception: - 1) Nothing in this schedule shall apply to any factory in which only repairs are carried on except any part thereof in which one or more persons are wholly or mainly employed in the grinding or glazing of metals. 2) Nothing in this schedule except paragraph 4 shall apply to any grinding or glazing of metals carried on intermittently and at which no person is employed for more than 12 hours in any week. 3) The Chief Inspector may by certificate in writing, subject to such conditions as he may specify therein, relax or suspend any of the provisions of this schedule in respect of any factory if owing to the special methods of work or otherwise such relaxation or suspension is practicable without danger to the health or safety of the persons employed. 3) Equipment for removal of dust: - No racing, dry grinding or glazing shall be performed without: - a) a hood or other appliance so constructed, arranged, placed, and maintained as substantially to intercept the dust thrown off; b) a duct of adequate size, air tight and so arranged as to be capable of carrying away the dust, which duct shall be kept free from obstruction and shall be provided with proper means of access for inspection and cleaning and where practicable, with a connection at the end remote from the fan to enable the Inspector to attach thereto any instrument necessary for ascertaining the pressure of air in the said duct; and c) a fan or other efficient means of producing a draught sufficient to extract the dust; Provided that the Chief Inspector may accept any other appliances, i.e., the opinion, as effectual for interception, removal and disposal of dust thrown off as a hood, dust and fan would be. 4) Restriction on employment on grinding operations: Not more than one person shall be at any time perform the actual process of grinding, or glazing upon a grindstone, abrasive wheel or glazing appliances. Provided that this paragraph shall not prohibit the employment of persons to assists in the manipulation of heavy or bulky articles at any such grindstone, abrasive wheel or glazing appliances. 188 5) Glazing: Glazing or other processes, except processes incidental to wet grinding upon a grindstone shall not be carried on in any room in which wet grinding upon a grindstone is done. 6) Hacking & Rodding: Hacking & Rodding shall not be done unless during the process either (a) and adequate supply of water is laid on at the upper surface of the grindstone or (b) adequate appliances for the interception of dust are provided in accordance with the requirements of paragraph 3. 7) Examination of Dust Equipment: a) All equipment for the extraction or suppression of dust shall at-least once in every six months be examined and tested by a competent person, and any defect disclosed by such examination and test shall be rectified as soon as practicable. b) A register containing particulars of such examination and tests shall be kept in a Form approved by the Chief Inspector. 8) Medical facilities and record of examinations and tests: - 1) The occupier of every factory in which grinding or glazing of metals are carried out, shall – a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector; and b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). 2) The record of medical examinations are appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 9) Medical examination by Certifying Surgeon: - 1) Every worker employed in grinding or glazing of metal and processes incidental thereto shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and in suspected cases chest X rays. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified for such employment by Certifying Surgeon. 2) Every worker employed in the said processes shall re-examined by a Certifying Surgeon at least once in every 12 calendar months. Such re- examintion shall, wherever the Certifying Surgeon considers approximate, include tests as specified in sub-paragraph (1). 3) The Certifying Surgeon after examining a worker, shall issue & Certificates of Fitness in Form 28. The record of examination and re- examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 29. 4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. 5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fir for employment in the said processes on the ground that continuance therein would involve special danger to the health of the 189 worker, he shall make a record of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapiciated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. 6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 10) Exemption: - The Chief Inspector may by certificate in writing, subject to such conditions as he may specify therein, relax or suspend any of the provisions of this schedule in respect of any factory if owing to the special methods of work or otherwise such relaxation or suspension is practicable without danger to the health or safety of the persons employed. Schedule VI Manufacture and treatment or lead and certain lead Compounds of Lead 1) Examination: Where the chief Inspector is satisfied that all or any of the provision of this schedule are not necessary for the protection of the persons employed he may by certificate in writing exempt any factory from all or any f such provision, subject to such conditions as he may specify therein. 2) Definition: - For the purpose of this schedule: - a) “Lead Compound” means any compound of lead other than galena which, when treated in the manner described below, yields to an aqueous solution of hydrochloric acid, quantity of soluble lead compound exceeding when calculated as lead monoxide, five percent of the dry weight of the portion taken for analysis, in the case of paints and similar products and other mixtures containing oils or fat the “dry weight” means the dry weight of the material remaining after the substance has been thoroughly mixed and treated with suitable solvents to remove oil, fats, varnish or other media. The method of treatment shall be as follows: - A weighted quantity of the material which has been dried at 100oC and thoroughly mixed shall be continuously shaken for one hour, at the common temperature with 1,000 times its weight of an aqueous solution of hydrochloric acid containing 0.25% by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The Lead salt contained in the clear filtrate shall then be precipitated as lead sulphide and weighed as lead sulphate. b) “Efficient exhaust draught” means localized ventilation affected by heat or mechanical means, for the removal of gas, vapour, dust or fumes so as to prevent them (as far as practicable under the atmosphere conditions usually prevailing) from the escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fumes or dust originate. 3) Application: - This schedule shall apply to all factories of parts of factories in which any of the following operations are carried on: - a) Work at a furnace where the reduction or treatment of zinc of lead ones is carried on. 190 b) The manipulation, treatment or reduction of ashes containing lead the desilerising of lead or the melting of scrap lead or zinc. c) The manufacture of solder or alloys containing more than ten per cent of lead. d) The manufacture of any oxide, carbonate, sulphate, chromate, acetate, nitrate or silicate of lead. e) Handling or mixing of lead-tetraethyl. f) Any other operation involving the use of a lead compound. g) The cleaning of work-rooms where any of the operations aforesaid and carried on. 4) Prohibited relating to women and young persons: - No woman or young person shall be employed or permitted to work in any of the operations specified in paragraph 3. 5) Requirements to be observed: - No person shall be employed or permitted to work in any process involving the use of lead compound is produced therein, or the persons employed therein ate liable to be splashed with any lead compound in the course of their employment unless the prohibitions of paragraphs 6 to 14 are compiled with. 6) Exhaust draught: - Where dust, fume, gas or vapour is produced in the process, provisions shall be made removing them by means of an efficient exhaust draught so contrived as to operate on the dust, fume, gas or vapour as closely as possible to the point of origin. 7) Certificate of fitness: - A person medically examined under paragraph B and found fit for employment shall be granted by a Certifying Surgeon a certificate of fitness in Form 28 and such certificate shall be in the custody of the manager of the factory. The certificate shall be kept readily available for inspection by any inspector and the person granted such a certificate shall carry with him, while at work, a token giving reference to such certificate. 8) Medical examination: - 1) The person so employed shall be medically examined by a Certifying Surgeon within fourteen days of his first employment in such process and thereafter shall be examined by the Certifying Surgeon at intervals of not more than three months, and a record of such examinations shall be entered by the Certifying Surgeon in the special certificate of fitness granted under paragraph 7. 2) If at any time the Certifying Surgeon is of opinion that any person is no longer fit for employment on the grounds that continuance therein should involve special danger to health he shall cancel the special certificate of fitness of that person. 3) No person whose special certificate of fitness has been cancelled shall be employed unless the Certifying Surgeon, after re-examination, again certifies him to be fit for employment. 8) A. Medical facilities: - 1) The occupier of the factory shall appoint at least a part-time qualified medical practitioner possessing MBBS degree and having post-graduate Diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner, so appointed, shall be required to put in minimum four hours 191 attendance on every working day in the ambulance room for carrying out the duties specified in the following sub-paragraph (2). Provided that in cases of factories employing less than 500 workers per day, the Chief Inspector of Factories, may allow attendance for shorter duration after taking into consideration all the relevant facts of each case. 2) The medical practitioner so appointed shall perform the following duties, that is to say: - a) to maintain Health Register. b) to undertake medical supervision of persons engaged on dangerous operations specified in these rules. c) to look after health, education and rehabilitation or sick, injured or affected workers. d) to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. e) For the purpose of medical supervision by the medical practitioner so appointed, the occupier shall provide for the former’s exclusive use at the factory premises a room which shall be properly cleaned, adequately lighted, ventilated and furnished with a screen, a table with office stationary, chairs and other facilities and instruments including X-ray arrangement for Schedules IV, X, XVII for such examination and such other equipments as may be prescribed by the Chief Inspector of Factories from time to time. 9) Food drinks, etc, prohibited in work-rooms: - No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any work-room in which the process is carried on and no person shall remain in such room during intervals for meals or rest. 10) Protective clothing: - Suitable protective overalls and head coverings shall be provided, maintained and kept clean by the factory occupier and such overalls and head coverings shall be worn by the persons employed. 11) Cleanliness of work-room, tools, etc. – The rooms in which the persons are employed and all tools and apparatus used by them shall be kept in a clean state. 12) Washing facilities: - 1) The occupier shall provide and maintain for the use of all persons employed suitable washing facilities consisting of – a) a trough with a smooth impervious surface fitted with a vaste pipe without plug and of sufficient length to allow at least two feet for every ten persons employed at my one time, and having a constant supply of clean water from tape or jet above the trough at intervals of not more than tow feet; or b) at least one wash-basin for every ten persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of clean water together with, in either case, a sufficient supply of nail brushes soap or other suitable cleaning material and clean towels. 2) The facilities so provided shall be placed under the charge of a responsible person and be kept clean; 13) Mess-room or canteen: - The occupier shall provide and maintain for the use of the persons employed suitable and adequate arrangements for taking their meals. The arrangement shall consists of the use of a room separate from any work-room 192 which shall be furnished with sufficient table and benches, and unless canteen serving hot meals is provided, adequate means for warming food. The room shall be adequately ventilated by the circulation of fresh air, shall be placed under the charge of a responsible person and shall be kept clean. 14) Clock-Room:- The occupier shall provide and maintain for the use of persons employed, suitable accommodation for clothing not worn during working hours, and for the drying of wet clothing. Schedule VII Generation of gas from Dangerous Petroleum as defined in the Petroleum Act, 1934. 1) Prohibition relating to women and young persons: No women or young person shall be employed or permitted to work in or shall be allowed to enter any building in which the generation of gas from dangerous petroleum as defined in clause (b) of section 2 of the Petroleum Act, 1934, is carried on. 2) Flame traps: The plant for generation of gas from dangerous petroleum as defined in clause (b) of section 2 of the Petroleum Act, 1934 and associated piping and fitting shall be fitted with at least two efficient flame traps so designed and maintained as to prevent a flash back from any burner to the plant. One of these traps shall be fitted as close to the plant as possible. The plant and all pipes and valves shall be installed and maintained free from leaks. 3) Generating Building or Room: All plants for generation of gas from dangerous petroleum as defined in clause (b) of section 2 of the Petroleum Act., 1934 erected after the coming into force of the provisions specified in the Schedule, shall be erected outside the factory building proper in a separate well ventilated building (hereinafter referred to as the “generating building”). In the case of such plant erected before the coming into force of the provisions specified in this Schedule there shall be no direct communication between the room where such plants are erected (herein after referred to as “the generating room”) and the remainder of the factory building. So far as practicable, all such generating rooms shall be constructed of fire-resisting materials. Provided that where the State Government is satisfied in respect of any factory that the plant for generation of gas from dangerous petroleum as defined in clause (b) of section 2 of the petroleum Act, 1934, is on account of the special precautions adopted or contrivances used for such plant, not likely to expose any persons employed in such factory to any serious risk of bodily injury, the State Government may, by notification on the Official Gazette, exempt such factory wholly or partially from the provisions of this clause for such period and on such conditions as it may specify. 4) Fire Extinguisher: An efficient means of extinguishing petrol fires shall be maintained in a easily accessible position near the plant for generating of gas from dangerous petroleum as defined in the Petroleum Act, 1934. 5) Plant to be approved by Chief Inspector: Petrol gas shall not be manufactured except in a plant for generating petrol gas, the design and construction of which has been approved by the Chief Inspector. 6) Escape of Petrol: Effective steps shall be taken to prevent petrol from escaping into any drain or sewer. 7) Prohibition relating to smoking etc.: No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in the generating room or building or in the vicinity thereof and a warning notice in the language understood by the majority of the workers shall be pasted in the factory 193 prohibiting smoking and the carrying of matches fire or naked light or other means of producing, naked light or spark in such room building. 8) Access to Petrol or Container: No unauthorised person shall be of flame-proof construction and all electric conductors shall either be enclosed in metal conducts or be lead-sheathed. 9) Electric Fittings: All electric fitting shall be of flame-proof construction and all electric conductors shall either be enclosed in metal conduits or be lead-sheathed. 10) Construction: All doors in the generating room of building shall be constructed to open outwards or to slide and no doors shall be locked or obstructed or fastened in such manner that it can not be easily and immediately opened from the inside while gas is being generated and any persons is working in the generating room or building. 11) Repair of Containers: No vessel that has contained petrol shall be repaired in a generating room or building and no repairs to any such vessel shall be undertaken unless live steam has been blown into the vessel and until the interior is thoroughly steamed out or other equally effective steps have been taken to ensure that it has been rendered free from petrol or inflammable vapour. Schedule VIII Cleaning or smoothening, roughening etc of articles by a jet sand, metal shot or grit or other abrasive propelled by a blast of Compressed Air or steam blasting regulations. 1) Definitions: “Blasting” means cleaning, smoothening, roughening, or removing of any part of the surface of any article by the use of an abrasive as a jet of sand, metal shot, or grit or other material, propelled by a blast or compressed air or steam. 1) “Blasting Enclosure” means a chamber, barrel, cabinet or any other enclosure designed for the performance of blasting therein. 2) “Blasting Chamber” means a blasting enclosure in which any person may enter at any time in connection with work or otherwise. 3) “Cleaning of Castings” where done as an incidental or supplemental process in connection with the makings of metal casting, means the freeing of the casting from adherent sand or other substance and includes the removal of cores and the general smoothening of a casting where freeing is done but does not include the freeing of casting from scale formed during annealing or heat treatment. 2) Prohibition of sand blasting: - Sand or any other substance containing free silica shall not be introduced as an abrasive into any blasting apparatus and shall not be used for blasting. Provided that this clause shall be brought into operation after two years from the date of commencement of these regulations. 3) Precautions in connection with blasting operations:- 1) Blasting to be done in blasting enclosure – Blasting shall not be done except in a blasting enclosure and no work other than blasting and any work immediately incidental thereto and clearing and repairing of the enclosure including the plants and appliances situated therein, shall be performed in a blasting enclosure. Every door, apparatus and joint of blasting enclosure shall be kept closed and airtight while basting is being done therein. 194 2) Maintenance of blasting enclosure: - Blasting enclosure shall always be maintained in good condition and effective measures shall be taken to prevent dust escaping from such enclosures, and from any blasting apparatus and used for blasting until it has been so separated. 3) Provision of separating apparatus: There shall be provided and maintained for and in connection with every blasting enclosure, efficient apparatus for separating, so far as practicable, abrasive, which has been used for blasting and which is to be used again as an abrasive, from dust or particles of other materials arising from blasting, and no such abrasive shall be introduced into any blasting apparatus and used for blasting until it has been so separated. Separating apparatus shall be provided with exhaust draught arrangement to extract and remove the dust by special methods and in such manner so that it shall not escape into air of any rooms in which person are employed. Provided that this clause shall not apply, except in the case blasting chambers, to basting enclosure constructed or installed before the coming into force of this Schedule, if the Chief Inspector is of the opinion that it is nor reasonably practicable to provide such separating apparatus. 4) Inspection and examination: - 1) Every blasting enclosure and/ or chamber shall be specially inspected for detecting leakages by a competent person at least once in every week in which it is used for blasting. Every blasting enclosure, the apparatus connected therewith and the ventilating plant shall be thoroughly examined and in the case of ventilating plant, tested by a competent person at least once in every three months. 2) Particulars of the result of every such inspection, examination and test shall forthwith be entered in a register, which shall be kept in a form approved by the Chief Inspector and shall be available for inspection by any workman employed in or in connection with blasting in the factory. Any defect found on any such inspection, examination or test shall be immediately reported by the person carrying out the inspection, examination or test to the occupier, manager or other appropriate person and without prejudice to the manager or other appropriate person and without prejudice to the foregoing requirements of this schedule, shall be removed without avoidable delay. 3) Every blasting chamber, separating apparatus, and ventilation plant shall be thoroughly inspected at an interval of 6 months for detecting any defect in their efficient operations, and the defects so noticed shall be rectified forthwith. 5) Provision of protective helmets gauntlets and overalls: - 1) There shall be provided and maintained for the use of all persons who are employed in a blasting chamber, whether in blasting or in any work connected therewith or in cleaning such a chamber, protective helmets of a type approved by a certificate of the Chief inspector, and every such person shall wear the helmet provided for his use while he is in the chamber and shall not remove it until he is outside the chamber. 2) Each protective helmet shall carry a distinguishing mark indicating the person by whom it is intended to be used and no person shall be allowed or required to wear a helmet not carrying his mark or a helmet which has been worn by another person unless it has been thoroughly disinfected. 195 3) Each protective helmet when in use shall be supplied with air at a rate of not less than six cubic feet per minute. The air supplied shall be cool and free from fumes or mist of mineral oil. 4) Suitable gauntlets, overalls, dust-proof goggles and boots shall be provided for the use of all persons while performing blasting or assisting blasting, and every such person shall, while so engaged, wear gauntlets and overalls provided. 6) Precautions in connection with cleaning and other work: - 1) Where any person is engaged upon cleaning of any blasting apparatus or blasting enclosure or separating apparatus or of any apparatus or ventilation plant connecting therewith of the surrounding thereof or upon any other work in connection with any blasting apparatus or with any blasting enclosure or with any apparatus or ventilating plant connected therewith so that he is exposed to the risk in inhaling dust which has arisen from blasting, all practicable measures shall be taken to prevent such inhalation. All the workers exposed to dust shall be provided with protective helmets with fresh air supply and overalls to prevent inhalation of dust. 2) In connection with any cleaning operation referred to in regulation 5, and with the removal of dust from filtering or settling devices all practicable measures shall be taken to dispose of the dust in such a manner that it does not enter the air of any room. Vacuum cleaners shall be provided and used for such cleaning operations. 7) Storage accommodations for protective wear: - Adequate and suitable storage accommodation for the helmets, gauntlets and overalls required to be provided under regulation 5 shall be provided outside and conveniently near to every blasting enclosure and such accommodation shall be kept clean. Helmets, gauntlets and overalls, when not in actual use, shall be kept in this accommodation. 8) Maintenance and cleaning of protective wear: - All members, gauntlets, overalls and other protective devices or clothing provided and worn for the purpose of this Schedule shall be kept in good condition and shall be cleaned on every week-day in which they are used. Where dust arising from the cleaning of such protective clothing or devices is likely to be inhaled all measures shall be taken to prevent such clothing and compressed air shall not be used for removing dust from any clothing. 9) Maintenance of vacuum cleaning plant: - Vacuum cleaning plant used for the purpose of this Schedule shall be properly maintained. 10) Prohibition relating to employment of women and young persons: - 1) No woman or young person under 18 years of age shall be employed in blasting or assisting at blasting or in any blasting chamber or in the cleaning of any blasting apparatus or any blasting enclosure or any maintenance or repair work at such apparatus, enclosure or plant. 2) No women or young person under 18 years of age shall be employed to work regularity within 20 feet of any blasting enclosure unless the enclosure is in a room and he or she is outside the room where he or she is effectively separated from any dust coming from the enclosure. 11) Medical Examination: 1) Every person employed in blasting or assisting at blasting or in any blasting chamber or in the cleaning of any blasting apparatus or any 196 blasting enclosure or any apparatus or ventilating plant connected therewith or be employed on maintenance or repair work at such apparatus, enclosure or plant shall be medically examined by the Medical Inspector of Factories/ Certifying Surgeon within 30 days of his first employment, the record of which shall be entered in Form 29 and if found fit for employment in the said process, he shall be granted by the Medical Inspector of Factories or Certifying Surgeon , a certificate of fitness in Form 28. 2) After the first examination, the persons so examined shall be examined by the Certifying Surgeon at intervals of twelve months and a records of such examination shall be entered by the Certifying Surgeon in Form 29. 3) If at any time the Medical Inspector of Factories/ Certifying Surgeon is of the opinion that the person employed in the said process shall be examined radiologically by a qualified radiologist, he may direct the occupier to arrange for such examination at his cost and then to submit standard size chest X-Ray plate of the worker to the Medical Inspector of Factories/ Certifying Surgeon. 4) If at any time Certifying Surgeon/ Medical Inspector of Factories is of the opinion that any person is no longer fit for employment on the grounds that continuance therein would involve special danger to health, he shall cancel the special certificate of fitness in Form 28 of that person and record in Form 29. 5) No person whose special certificate of fitness in Form 28 has been cancelled, shall be employed or permitted to work unless the Certifying Surgeon after re-examination, again certifies him to be fit for employment in the operations. 6) The register of the special certificates in Form-28 granted by the Certifying Surgeon and the record made in Form No 29 by him shall be in the custody of the manager of the factory and shall be kept readily available for inspection by an Inspector. 12) Medical facilities & records: - Medical facilities and records of examinations and tests - 1) The occupier of every factory to which the schedule applies, shall – a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment small be subject to the approval of the Chief Inspector of Factories; b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). 2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 13) Power to exempt or relax: - 1) If the Chief Inspector is satisfied that in any factory or any class of factories the use of sand or other substance containing free silica as an abrasive in blasting is necessary for a particular manufacture of process (other than the process incidental or supplemental to making of metal castings) and that the manufacture of process cannot be carried on without the use of such abrasive or that owing to the special conditions or special method of work or otherwise any requirement of this schedule can be 197 suspended either temporarily or permanently, or can be relaxed without endangering the health of the persons employed or that application of any of such requirements is for any reason impracticable or inappropriate, he may, with the previous sanction of the State Government by an order in writing exempt the said factory or class or factories from such provisions of this Schedule, to such extent and subject to such conditions and for such period as may be specified in the said order. 2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separated register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 13. Power to exempt or relax: - 1) If the Chief Inspector is satisfied that in any factory or any class of factories the use of sand or other substance containing free silica as an abrasive in blasting is necessary for a particular manufacture of process (other than the process incidental or supplemental to making of metal castings) and that the manufacture or process cannot be carried on without the use of such abrasive or that owing to the special conditions or special method of work or otherwise any requirement or this schedule can be suspended either temporarily or permanently, or can be relaxed without endangered the health of the persons employed or that application of any of such requirements is for any reason impracticable or inappropriate, he may, with the previous sanction of the State Government by an order in writing exempt the said factory or the State Government by an order in writing exempt the said factory or class or factories from such provisions of this Schedule, to such extent and subject to such conditions and for such period as may be specified in the said order. 2) Where an exemption has been granted under paragraph (1) a copy of the order shall be displayed on a notice-board at a prominent place at the main entrance or entrance to the factory and also at the place where the blasting is carried on. Schedule IX Liming and tanning of the raw hides and skins and processes incidental thereto 1) Cautionary notices: - 1) Cautionary notice as to anthrax in the from specified by the Chief Inspector shall be affixed in prominent positions in the factory where they may easily and conveniently read by the persons employed. 2) A copy of a warning notice as to anthrax in the form specified by the Chief Inspector shall be given to each person employed when he is engaged and subsequently if still employed on the first day of each calendar year. 3) Cautionary notices as to the effects of chrome on the skin shall be affixed in prominent positions in every factory in which chrome solutions are used and such notices shall be so placed as to be easily and conveniently read by the persons employed. 4) Notices shall be affixed in prominent places in the factory stating the position of the “First Aid” box or cupboard and the name of the person in charge of such box or cupboard. 198 5) If any person employed in the factory is illiterate, effective steps shall be taken to explain carefully to such illiterate person the contents of the notices specified in paragraphs 1, 2, and 4 and if chrome solution are used in the factory, the contents of the notice specified in paragraph 3. 2) Protective Clothing: The occupier shall provide and maintain in good conditions the following articles of protective clothing: - a) Water proof foot-wear, leg coverings, aprons and gloves for persons employed in process involving contact with chrome solutions including preparation of such solutions. b) gloves, boots and chemical safety goggles for persons employed in lime- yard, and c) protective foot-wear, aprons and gloves for persons employed in processes involving the handling of hides or skins, other than in processes specified in clauses (a) and (b). Provided that: i) the gloves, aprons, leg coverings or boots may be of rubber or leather, but the gloves and boots to be provided to persons fleshing by hand or employed in processes in which there is no risk of contact with lime. ii) the gloves may not be provided to persons fleshing by hand or employed in processes in which there is no risk of contact with lime, sodium sulphide or other caustic liquor. 3) Washing facilities, Mess room and cloak room: The occupier shall provide and maintain in a clean state and in goof repair for the use of all persons employed: a) a trough with a smooth impervious surface fitted with a washed pipe without plug and of sufficient length to allow at least 60 cm for every 10 persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 cm or b) atleast wash basin for every 10 such persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of water together with in either case, a sufficient supply of nail brushes, soap or other suitable cleansing material and clean towels. c) a suitable mess room, adequate for the number remaining on the premises during the meal intervals, which shall be furnished with (1) sufficient tables and benches and (2) adequate means for warming food and for boiling water. The mess room shall (1) be separated from any room or shed in which hides or skins are stored, treated or manipulated, (2) be separated from the cloak room and (3) be placed under the charge of a responsible. d) suitable accommodation for clothing put off during working hours and separate accommodation for protective clothing and adequate arrangement for drying up the clothing in both the cases, if wet. The accommodation so provided shall be kept clean at all times and placed under the charge of responsible person. 4) Food, drink, etc. prohibited in work-rooms – No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any work-room or shed in which hides or skins are stored, treated or manipulated. 5) First-aid arrangement – The occupier shall – 199 a) arrange for an inspection of the hands of all persons coming into contact solutions to be made twice a week by reasonable persons. b) provide and maintain a sufficient supply of supply of suitable ointment and impermeable water proof plaster in a box readily accessible to the worker and used solely for the purpose of keeping the ointment and plaster. Schedule X Manufacture of chromic acid or manufacture or recovery of the bichromate of sodium potassium or ammonium 1. Definitions: - For the purpose of this Schedule – a) “Chrome Process” means the manufacture of chromic acid or bichromate of sodium or potassium or ammonium or the manipulation, movement or other treatment or these substances in connection with their manufacture; b) “Efficient exhaust draught” means localised ventilations effected by mechanical or other means for the removal of gas, vapour, dust or fumes, so as to prevent from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated to the point where such gas, vapour, fumes or dust originate; c) “Suspension” means suspension form employment in any of the chrome processes specified by written certificate in the Health Register in Form 29 signed by the Certifying Surgeon who shall have power of suspension as regards all persons employed in any such process. 2. Prohibition relating to women and young persons: - No woman or young person shall be employed or permitted to work on any chrome process. 3. Efficient exhaust draught: - The following chrome processes shall not be carried on without the use of an efficient exhaust draught, namely: - a) grinding; b) sieving; c) batch mixing; d) concentration; 4. Separation of certain process: - The following chrome processes, name: - a) grinding of raw materials and b) sieving of raw materials. shall be carried on in such manner and under such conditions as to secure effectual separation from any other processes. 5. Washing facilities: - 1. Where acidification, sulphate settling or washing concentration crystallisation, centrifugation or packing is carried out, there shall be provided close to each worker’s station: - a) wash places installed for washing hands and feet frequently in running water, and b) a container holding at least 500 millilitres of 10 percent solution of sodium bisulphate or any other suitable reducing agent. 2. There shall also be provided and maintained in a cleanly state and good repair washing accommodation under cover with a sufficient supply of soap and towels on the scale indicated below: - 200 At least one tap or stand pipe for every 10 employees and the tap or pipe shall be spaced not less than 120 centimetre apart. Note: - In computing the total number of tape required for the purposes of this rule, the taps or stand pipes as required under clause 5(1) (a) shall be included. 6. Time to be allowed for washing: - Before each meal and before the end of the day’s work at least ten minutes, in addition to the regular meals time, shall be allowed for washing to each person employed in a chromic process. 7. Flooring: - The floor of every work-room shall be – a) of cement or similar other material so as to be smooth and impervious to water and provided with suitable gradient and drainage; b) maintained in sound condition and cleaned daily; 8. Medical facilities: - 1. The occupier of the factory shall appoint at least a part-time qualified medical practitioner, possessing MBBS degree and having post-graduate Diploma in Industrial Health of processing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner, so appointed, shall be examine and treat all workers, for chrome ulcerations and occupational diseases, on the premises at least at thrice a week. The medical practitioner so appointed, shall be required to put in minimum four hours attendance on every working day in the ambulance-room for carrying out the duties specified in the following sub paragraph (2). Provided that, in the case of factories employing less than 500 workers per day, the chief Inspector of Factories may allow attendance for shorter duration, after taking into consideration all the relevant facts of each case. 2. The medical practitioner so appointed shall perform in addition to the duties specified in sub-paragraph (1) the following duties that is to say: - a. to maintain Health Register in Form 29. b. to undertake medical supervision of persons engaged on dangerous operations specified in rule 165 of these rules. c. to look after health, education and rehabilitation of sick, injured or affected worker; d. to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. 3. The occupier shall in addition appoint a person trained in First Aid who shall inspect daily the hands and feet of all persons employed and shall keep a record of such inspection may register maintained for the purpose in a Form approved by the Chief Inspector of factories; 4. The occupier shall also provide and maintain a sufficient supply of suitable antidotes, ointment and impermeable water-proof plaster in a separate box readily accessible to the workers and used solely for the purpose of keeping the antidotes, ointment and plaster. 9. Protective equipment: - 1. The occupier shall provide and maintain for the use pf the persons employed: - 201 a) in grinding, sieving, or mixing raw materials, sufficient and suitable respirators (issued separately for each individual) the filtering materials of which shall be renewed daily; b) in roasting process, suitable footwear; c) in acidification, settling, concentration, crystallisation, centrifugation packing, suitable aprons and protective coverings for hands and feet. 2. Arrangements shall be made by the occupier for the examination and cleaning of all the protective equipment at the close of each day’s work and for the renewal thereof when necessary. 10. Use of protective equipment: - Every person employed in a chrome process shall make use of the protective equipment provided under paragraph 9 above. 11. Cloak room: - There shall be provided and maintained in a clean and in good repair for the use of all persons employed in any chrome process: - a) a cloak-room for street clothing put off during working hours, including adequate arrangements for drying such clothing, when wet; such accommodation shall be separate form any mess-room; b) separate and suitable arrangements for the storage of protective clothing provided under paragraph 9. 12. Mess-room: - 1. There shall be provided and maintained for the use of all persons remaining within the premises during the meal intervals a suitable mess- room providing accommodation of at least one square metre per head and furnished with - i) a sufficient number of tables and chairs or benches; ii) arrangements for washing utensils; iii) adequate means for washing food. 2. The mess-room shall be placed under the charge of a responsible person and shall be kept clean 13. Food, drinks, etc, prohibited in workrooms: - No food, drink, pan, supari or tobacco shall be brought or carried on and no person shall remain in any such room during intervals for meals or rest. 14. Medical examination: - 1. Every person employed in a chrome process, shall be examined by the Certifying Surgeon once in every calendar month or at such other intervals as may be specified in writing by the Chief Inspector on a day of which due notice shall be given to all concerned and such examination shall take place on the factory premises. 2. A Health Register in Form 29 containing the names of all persons employed in a chrome process shall be kept. 3. No person after suspension shall be employed in chrome process without a written sanction from the Certifying Surgeon entered in the Health Register. 15. Fencing of vessels: - Every fixed vessel, whether pot, pan, vat or other structure, containing any dangerous materials, and not so covered as to eliminate all reasonable risk of accidental immersion of any portion of the body of a person employed shall be fenced as follows: - 202 a) Each such vessel shall, unless its edge is at least one metre above the adjoining ground or platform, be securely fenced to a height of at least 90 centimetres above such adjoining ground or platform. b) No plank or gang-way shall be placed across or inside any such vessel unless such plank or gang-way is: - i) at least 45 centimetres wide, and ii) securely fenced on both sides, either by upper and lower rails, to a height of 90 centimetres or by other equally efficient means; c) If any two such vessels are near each other and the space between them clear of any surrounding brick-work or other work, is either - i) less than 45 centimetres in width, or ii) is 45 or more centimetres in width, but is not accurately fenced on both sides to a height of at least 90 centimetres secure barrier shall be placed so as to prevent any passage between them. 16. Cautionary notice: - A cautionary notice in the form specified by the Chief Inspector and printed in the language of the majority of the workers employed shall be affixed in a prominent place in the factory where it can be easily and conveniently read by the workers. 17. Exemption: -If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or the in frequency of the process, or for any other reason, all or any of the provisions of this Schedule are not necessary for the protection of the persons employed in such factory, he may by certificate in writing exempt such factory from all or any of the provisions indicated in such certificate on each conditions as he may specify therein, such certificate may at any time be revoked by the Chief Inspector, without assigning any reasons. Schedule XI Manufacture or manipulation of Nitro or Amino compounds 1. Application: - This Schedule shall apply in respect of all factories or any park thereof in which process of manufacturing of a nitro or amino compound (therein after referred to as the said manufacturing process) is carried on; Provided that clause paragraphs 25 and 26 shall only apply to a process involving manufacture or manipulation of compound in Appendix B (hereinafter referred to as the said manufacturing process B). Part I 2. Definitions: - a) For the purpose of this Schedule a nitro or amino compound means a nitrated or aminated compound of aromatic hydrocarbons mentioned in Appendix ‘A’ or ‘B’ attached thereto. b) “Approved” means approved by the Chief Inspector. c) “First Employment” means first employment in the said manufacturing process and also re-employment in such manufacturing process following any cessation of employment for continuous period exceeding three calendar months. d) “Efficient Exhaust Draught” means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fume so as to, prevent them from escaping into the air or any place in which work is 203 carried on. No draught shall be deemed to be efficient which fails to remove smoke generated at the point where such gas, vapour, fumes or dust originates. e) Manipulation shall include mixing, blending, filling, emptying, grinding, sleving, drying, packing, sweeping, handling, using or chemical processing of a nitro amino compound. f) “Air Line respiration” means a helmet or face piece with necessary connections by means of which a person using it in a poisonous or irritant atmosphere breathe ordinary air or any other suitable apparatus approved in writing by the Chief Inspector. 3) Cautionary Placard: - Cautionary placard in the form specified in Appendix ‘C’ attached to this Schedule and printed in the language of the majority of the workers employed shall be affixed in prominent places frequented by them in the factory where the placards can be easily and conveniently read by the workers; and arrangement shall be made by the occupier to instruct periodically all workers employed in the said manufacturing process regarding the precautions contained in the cautionary placard. 3.A) Instructions as regards risk: -Every worker on his first employment shall be fully instructed about the properties of the chemicals he has to handle and the dangers involved in his work. He shall also be instructed about the measures required to be taken to deal with any emergency arising in the said manufacturing process. 4. Prohibition relating to employment of women and young persons: -No woman or young person shall be employed or permitted to work in any room in which the said manufacturing process is carried on or in which a nitro or amino compound is stored. 5. Air Space: - In every room in which the said manufacturing process is carried on there shall be at least 15 Cubic metre of air space excluding any space occupied by machinery equipment or any other article, for each person employed therein and in computing this air space no height over 4.25 metres shall be taken into account. 6. Efficient exhaust draught: - Unless the said manufacturing process is completely enclosed so as not to give rise to dust or fume it shall not be carried on without the use of an efficient exhaust draught when a nitro or amino compound - a) is introduced into a tank, hopper, machine or container or filled into cartridge; or b) is ground , crushed, mixed, sieved or blended. 7. Floor of workrooms: - The floor of every work-room in which the said manufacturing process is carried on shall be (a) smooth and impervious to water provided that asphalt or tar shall not be used in the composition of the floor (b) maintained in sound condition, (c) sloping and provided with gutters and (d) thoroughly washed daily by means of hose-pipe and drain water shall be led into a sewer through a closed channel. 8. Work-benches: - Work-benches on which a nitro or amino compound is manipulated shall (a) have a smooth impervious surface (of stainless steel) and (b) shall be washed daily with hose-pipe of cleaned by means of a suction cleaning apparatus at a time when no other work is being carried on thereat. 9. Waste: - 204 1) A suitable receptacle made of non-absorbable material with a tightly fitting cover, shall be provided and used for depositing waste, like cloth, paper or other materials soiled with a nitro or amino compound. 2) All such contaminated waste material shall be destroyed by burning at least once a week. 10. Empty containers: - Empty containers used for holding compound included under Appendix “A” shall be thoroughly cleaned of their contents and treated with an inactivating agent before being discarded. Empty non-metallic container used for holding compounds included under Appendix ‘B’ shall be burnt. Residual content of the metallic container shall be burnt out. 11. Decontamination of pit tank etc.: - a) Before a worker enters a tank, pit, kettle or any other confined space which contained a nitro or amino compound it shall be thoroughly washed and decontaminated. b) No part of the plant which has contained a nitro or amino compound shall be repaired or opened for repairs unless it has been emptied of such compound, thoroughly washed and decontaminated. c) Records of such treatment shall be maintained in a Register approved by the Chief Inspector and the register shall be made available for inspection when required by an inspector. 12. Manual handling: - A nitro or amino compound shall not be required or allowed to be mixed, filled, emptied or handled except by means of a scoop with a handle which shall be thoroughly cleaned daily. 13. Protective wear: - The occupier shall provide, maintain clean and in good repair protective clothing and other equipment as specified in the table below: - Process Protective clothing and other equipment For manipulation of compounds a) Long pants and shirts or overall mentioned in Appendices ‘A’ and ‘B’ with long-sleeves and head covering. The shirt of overalls shall cover the neck completely. b) Rubber gloves, rubber gum boots, rubber aprons and air line respirator. For manipulation of compounds a) White clean clothing mentioned in mentioned in Appendix ‘B’ (a) above in addition to white clean shirts singlet and protective equipment as in (b) above. b) White long-sleeved apron. 14. Medical Facilities: - 1) The occupier of the occupier of the factory shall appoint at least a part- time qualified medical practitioner, possessing MBBS degree and having post-graduate Diploma in Industrial Health or possessing MBBS degree and having five years experience in industry as occupational health physician. The medical practitioner, so appointed, shall be required to put in minimum four hours attendance on every working day in the ambulance 205 room for carrying out the duties specified in the following sub-paragraph (2). Provided that, in cases of factories employing less than 500 workers per day, the Chief Inspector of Factories may allow attendance for shorter duration, after taking into consideration all the relevant facts of each case. 2) The medical practitioner so appointed shall perform the following duties, that is to say: - a) to maintain Health Register in Forms 29. b) to undertake medical supervision of persons engaged engaged on dangerous operations specified in rule 163 of these rules; c) to took after health education and rehabilitation of sick, injured or affected workers; d) to carry out inspection of work-rooms where dangerous operations are carried out and to advise the management of the measures to be adopted for protection of health of the workers involved therein. 3) For the purpose of medical supervision by the medical practitioner so appointed the occupier shall provide for his exclusive use a room in the factory premises which shall be properly cleaned, adequately lighted, ventilated, and furnished with a screen, a table with office stationary, chairs and other facilities and instruments including X-Ray arrangements for Schedules IV, X and XVII, for such examination and such other equipments as may be prescribed by the Chief Inspector of Factories from time to time. 15. Medical examination: - 1. a) No person shall be employed in the said manufacturing process unless he has been examined by using appropriate tests, and found fit for the said process by the appointed doctor. Results of such examination shall be entered in a register approved by the Chief Inspector. The register shall contain the names of workers employed in the said manufacturing processes ‘A’ and ‘B’ separately. b) The person examined in compliance with sub-paragraph (1) (a) shall be re- examined by the appointed doctor at intervals of not more than three months or at such interval as may be directed in writing by the Chief Inspector, and records or such examination shall be entered in the register provided under the said sub-paragraph. c) If at any time, the appointed doctor is of opinion that any person is no longer fit for employment in the said manufacturing process on the ground that continuance thereat would involve special danger to health he shall make a record of his findings in the said register and intimate the manager in writing that the said person is unfit to work in the said manufacturing process. d) A person so found unfit by the appointed doctor shall be sent by the manager to the Certifying Surgeon with a report from the appointed doctor. The Certifying Surgeon after examination may suspend the said person from work in the said manufacturing process. 2. a) A person employed in the said manufacturing process shall be medically examined by a Certifying Surgeon within thirty days of his first employment in such process and if found fit for employment in the said process he shall be granted by the Certifying Surgeon a certificate if 206 fitness in Form No. 28. The person granted such a certificate shall carry with him, while at work, a token giving reference to such certificate. b) After the first examination the person so examined shall be examined by the Certifying Surgeon at intervals of not more than twelve months and a record of such examination shall be entered by the Certifying Surgeon in the special certificate of fitness in Form No. 28. c) If any time the Certifying Surgeon is of the opinion that any person is no- longer fit for employment on the ground that continuance therein would involve special danger to health he shall cancel the special certificate of fitness in Form No. 28 of that person. d) No person whose special certificate of fitness in Form No. 28 has been cancelled shall be employed or permitted to work unless the Certifying Surgeon after re-examination, again certificates him to be fit for employment in the said process. 3. The register of results of examination maintained by appointed doctor referred to in sub-paragraph (1) (a) and the special certificates in Form No. ______ granted by the Certifying Surgeon be in the custody of the manager of the factory and shall be kept readily available for Inspection by an Inspector. 4. No person other than the person granted a certificate of fitness in Form 28 by the Certifying Surgeon and carrying a token referred to in Sub- paragraph (2) (a) above shall be allowed to work in any work-room in which the said manufacturing process is carried on. 16. Washing and bathing facilities: - 1) The following washing and bathing facilities shall be provided and maintained in cleanly state and in good repair for the use of all persons employed in the said manufacturing process: - a) A wash place under cover with clean towels, soap and nail brushes and with at least one stand pipe for every five such persons having constant supply of water. b) 50 percent of the stand pipes provided under item (1) above shall be located in bathroom where both hot and cold water shall be made available during the working hours of the factory and for one hour thereafter. c) The washing and bathing facilities shall be within a radius of 15 metres from the area housing the said manufacturing process. d) Clean towels shall be provided individually to each worker if so ordered by an Inspector. e) In addition to taps mentioned under item (a), one stand pipe in which warm water is made available shall be provided on each floor. 2) Arrangements shall be made to wash factory uniforms/ clothing compulsory every day. 17. Washing and bathing: - a) All workers employed in the said manufacturing process shall carefully wash their hands and face before partaking of food of leaving the factory. b) Bath register: - Workers employed in the said manufacturing process shall take a bath daily at the factory premises and enter their names in the bath register in token of having done so. 207 18. Food, drinks etc. prohibited in work-room: - No worker shall consume food, drink, pan, supari or tobacco or shall smoke in any work-room in which the said manufacturing process its carried on and no worker shall remain in any such room during intervals for meal or rest. 19. Cloakroom: - There shall be provided and maintained in clean state and in good repair for the use of the persons employed in the said manufacturing process (a) a cloak room with lockers having two compartments one for street clothes and the other for factory clothes, (b) a place, separate from locker room and from the mess-room, for the storage of protective equipment provided under paragraph 13. The accommodation provided shall be under the care of a responsible person and shall be kept clean.

Previous and next

All provisions of Tripura Factories Rules, 2007

Questions people ask

Is rule 19 of Tripura Factories Rules, 2007 still in force?

No repeal of Tripura Factories Rules, 2007 is recorded.