LawGrids logoLAWGRIDS.ORG

Rule 9, Tripura Factories Rules, 2007: The following parts of factories

Tripura Factories Rules, 2007 - Rule 9

Text of rule 9

The following parts of factories

9. The following parts of factories:- a) Rooms used only for the storage of articles. b) Rooms in which the walls or ceilings consist of galvanized iron, glazed bricks, glass, slate, asbestos, bamboo or thatch. c) Parts in which dense steam is continuously evolved in the process. d) Parts in which pitch, tar or like material is manufactured or is used to a substantial extent, except in brush works. e) Parts of a glass factory known as glass house. 20 f) Rooms in which graphite is manufactured or is used to a substantial extent in any process. g) Parts in which coal, coke, oxide of iron, ochre, lime or stone is crushed or ground. h) Parts of wall, partitions, ceilings or tops of rooms which are at least 6 meters above the floor. i) Ceilings or tops of rooms in print works, bleach works or dye works, with the exception of finishing rooms or warehouses. j) Inside walls of oil mills below a height of 1.5 meters from the ground floor level. k) Inside walls in tanneries below a height of 1.5 meters from the ground floor level where a wet process is carried on. Part-B 1. Coach and motor body works. 2. Electric generating or transforming stations. 3. Engineering works. 4. Factories in which sugar is refined or manufactured. 5. Foundries other than foundries in which brass casting is carried on. 6. Gun factories. 7. Shipbuilding works. 8. Those parts of factories where unpainted or unvarnished wood is manufactured. Rule 27. Deleted 1 Rule 28. Compound to be kept clean. The compound surrounding every factory shall be maintained in a sanitary and clean condition free of bushes, rubbish, filth or debris. Rule 29. Disposal of trade wastes and affluent [Rules under sub-section (2) of section (12)] 1. In the case of a factory where the drainage system is proposed to be connected to the public sewerage system, prior approval of the arrangements made shall be obtained from local authority. 2. In the case of a factory situated in a place where no public sewerage system exists, prior approval of the arrangements made for proposal of trade wastes and effluent shall be obtained from the Public Health Authorities or the Tripura State Pollution Control Board appointed under the Water (Prevention and Control of Pollution) Act, 1974 and the Air (Prevention and Control of Pollution) Act, 1981. 3. Rubbish, filth or debris shall not be allowed to accumulate or to remain in any part of the premises in a factory for more than 24 hours and shall be disposed in a manner approved by the Public Health Authorities and filth and other decomposing matter shall be kept in covered receptacles. ___________________________________________________________________________ Tenth amendment vide No.7(121)-FB/AM(Vol.-II)/2007/2199-07 dated 27.01.2021 21 4. Wastes and effluent resulting from factory or industrial processes and which may be of injurious or obnoxious substances, shall not be disposed of without being suitably treated to render them unobjectionable to the satisfaction of the Public Health Authorities and of the Inspector. If any objection is raised by the arises between the Public Health Authorities and the Inspector with regard to treatment of wastes and other effluents under this rule, the matter shall be referred to the Chief Inspector whose decision shall be final. 5. All open drains carrying waste or sewage water or sewerage shall be constructed of masonry or other impermeable material and shall be regularly flushed at least twice daily and, where possible connected with some recognized drainage line. Rule 30. Ventilation and temperature (Rule prescribed under section 13) 1. Limits of temperature and air movement :- In any factory the maximum wet-bulb temperature of air in a workroom at a height of 1.5 meters above the floor level shall not exceed 300 centigrade and adequate air movement of at least 30 meters per minute shall be provided ; and in relation to dry-bulb temperature, the wet-bulb temperature in the workroom at the said height shall not exceed that shown in the schedule annexed hereto, or as regards a dry-bulb readings intermediate between the two dry-bulb readings that specified in relation to the higher of these two dry-bulb readings : Schedule Dry-bulb temperature Wet-bulb temperature (Degrees in Centigrade) (Degrees in Centigrade) 30 to 34 29 35 to 39 28.5 40 to 44 28 45 to 47 27.5 Provided that if the temperature measured with a thermometer inserted in a hollow globe of 15 centimeters diameter coated mat black outside and kept in the environment for not less than 20 minutes exceeds the dry -bulb temperature of air, the temperature so recorded by the globe thermometer shall be taken in place of the dry-bulb temperature. Provided further that when the reading of the wet-bulb temperature outside in the shade exceeds 270 C, the value of the wet-bulb temperature allowed in the schedule for a given dry- bulb temperature may be correspondingly exceeded to the same extent. Provided further that this requirement shall not apply in respect of factories covered by Section 15 of the Act and in respect of factories where the nature of work carried on involves production of excessively high temperature referred to in clause (b) of sub-section (1) of Section 13 to which workers are exposed for short periods of time not exceeding one hour followed by an interval of sufficient duration in thermal environments not exceeding those otherwise laid down in this rule. Provided further that the Chief Inspector having due regard to the health of the workers, may in special and exceptional circumstances, by an order in writing exempt any factory or part of a factory from the foregoing requirement, in so far as restricting the thermal 22 conditions within the limits laid down in the schedule are concerned, to the extent that he may consider necessary subject to such conditions as he may specify. 2. Provisions of thermometers – a) If it appears to the Inspector that in any factory, the temperature of air in a workroom is sufficiently high and is likely to exceed the limits prescribed in sub-rule (1), he may serve on the manager of the factory an order requiring him to provide sufficient number of whirling hygrometers or any other type of hygrometers and direct that the dry-bulb and wet-bulb readings in each such workroom shall be recorded at such positions as approved by the Inspector twice during each working shift by a person especially nominated for the purpose by the manager and approved by the Inspector. b) If the Inspector has reason to believe that a substantial amount of heat is added inside the environment of a workroom by radiation from walls, roof or other solid surroundings, he may serve on the manager of the factory an order requiring him to provide one or more globe thermometers referred to in the first provision in sub-rules (1) and further requiring him to place the globe thermometers at places specified by him and keep a record of the temperatures in a suitable register. 3. Ventilation:- a) In every factory the amount of ventilating openings in a workroom below the caves shall, except where mechanical means of ventilation as required by clause (b) below are provided, be of an aggregate area of not less that 15% of the floor area and so located as to afford a continued supply of fresh air: Provided that the Chief Inspector may relax the requirements regarding the amount of ventilating openings if he is satisfied that having regard to the location of the factory, orientation of workroom, prevailing wings, roof height and the nature of manufacturing process carried on, sufficient supply of fresh air into the workroom is afforded during most part of the working time. Provided further that this requirement shall not apply in respect of workrooms of factories – (i) covered by Section 15, or (ii) in which temperature and humidity are controlled by refrigeration. b) Where in any factory owing to special circumstances such as situation with respect to adjacent buildings and height of the building with respect to floor space, the requirements of ventilation openings under clause (a) of this sub-rule cannot be complied with or in the opinion of the Inspector the temperature of air in a workroom is sufficiently high and it is likely to exceed the limits prescribed in sub-rule (1), he may serve on the manager of the factory an order requiring him to provide additional ventilation either by means of roof ventilators or by mechanical means. 23 c) The amount of fresh air supplied by mechanical means of ventilation in an hour shall be equivalent to at least 6(six) times the cubic capacity of the workroom and shall be distributed evenly throughout the workroom without dead air- pockets or undue draughts caused by high inlet velocities. d) In the regions where in summer (15th March – 15th July) dry-bulb temperatures of outside air in the shade during most part of the day exceed 35 degrees centigrade and simultaneous wet-bulb temperatures are 25 degree centigrade or below and in the opinion of the Inspector the manufacturing process carried on in the workroom of a factory permits thermal environments with relative humidity of 50% or more, the Inspector may serve on the manager of the factory an order to have sufficient supply of outside air for ventilation cooled by passing it through water sprays either by means of unit type of evaporative air coolers (desert coolers) or, where supply of outside air is provided by mechanical means through ducts in a plenum system, by means of central air washing plants. Rule 31. When artificial humidification not allowed [Rules prescribed under sub-section (1) of Section 15)] There shall be no artificial humidification in any room of a cotton spinning or weaving factory – a) By the use of steam during any period when the dry-bulb temperature of that room exceeds 29.5 C; and b) At any time when the wet-bulb reading of the hygrometer is higher than that specified in the following schedule in relation to the dry-bulb reading of the hygrometer at that times; or as regards a dry-bulb reading intermediate between any two dry-bulb readings indicated consecutively in the schedule when the dry- bulb reading does not exceed the wet-bulb reading to the extent indicated in relation to the lower of these two dry-bulb readings: - Schedule Dry-bulb Wet-bulb (Readings in degrees centigrade) Dry-bulb Wet Bulb Dry-bulb Wet-bulb 15.5 14.5 25.0 24.0 34.5 30.0 16.0 15.0 25.5 24.5 35.0 30.5 16.5 15.5 26.0 25.0 35.5 31.0 17.0 16.0 26.5 25.5 36.0 31.0 17.5 16.0 27.0 26.0 36.5 31.5 18.0 16.5 27.5 26.0 37.0 31.5 18.5 17.0 28.0 26.5 37.5 31.5 19.0 18.0 28.5 27.0 38.0 32.0 19.5 18.5 29.0 27.0 38.5 32.0 20.0 19.0 29.5 28.0 39.0 32.0 24 20.5 19.5 30.0 28.0 39.5 32.5 21.0 20.0 30.5 28.5 40.0 32.5 21.5 20.5 31.0 28.5 40.5 33.0 22.0 21.0 31.5 29.0 41.0 33.0 22.5 21.0 32.0 29.0 41.5 33.0 23.0 21.5 32.5 29.0 42.0 33.0 23.5 22.0 33.0 29.5 42.5 33.0 24.0 23.0 33.5 29.5 43.0 33.5 24.5 23.5 34.0 30.0 43.5 33.5 Provided, however, that clause (b) shall not apply when the difference between the wet-bulb temperature as indicated by the hygrometer in the department concerned and the wet-bulb temperature taken with a hygrometer outside in the shade is less than 2 degrees. Rule 32. Provision of hygrometers – In all departments of cotton spinning and weaving mills wherein artificial humidification is adopted, hygrometers shall be provided and maintained in such positions as are approved by the Inspector. The number of hygrometer shall be regulated according to the following scale:- a) Weaving department – One hygrometer for departments with less than 100 looms, and one additional hygrometers for every 100 or part of 100 looms in excess of 100. b) Other departments- One hygrometer for each room of less than 1700 cubic meters capacity and one extra hygrometer for each 1130 cubic meters or part thereof, in excess of this. c) One addition hygrometer shall be provided and maintained outside each cotton spinning and weaving factory wherein artificial humidification is adopted, and in a position approved by the inspector, for taking hygrometer shade readings. Rule 33. Exemption from maintenance of hygrometers When the Inspector is satisfied that the limits of humidity allowed by the schedule to rule 31 are never exceeded, he may, for any department other than the weaving department, grant exemption from the maintenance of the hygrometer. The Inspector shall record such exemption in writing. Rule 34. Copy of schedule to rule 31 to be affixed near every hygrometer – A legible typed copy of the schedule to rule 31, duly authenticated with the Signature of either the occupier or the Manager, shall be affixed near each hygrometer. Rule 35. Temperature to be recorded at each hygrometer – At each hygrometer maintained in accordance with rule 32, correct wet & dry-bulb temperatures shall be checked thrice daily during each working day at a proportional period of interval by competent person nominated by the manager and approved by the Inspector. _______________________________________________________________________ Tenth amendment vide No.7(121)-FB/AM(Vol.-II)/2007/2199-07 dated 27.01.2021 25 Rule 36. Specification of hygrometer – 1) Each hygrometer shall comprise of two mercurial thermometers of wet-bulb and dry- bulb of similar constructions, and equal dimensions, scale and divisions of scale. They shall be mounted on a frame with a suitable reservoir containing water. 2) The wet-bulb shall be closely covered with a single layer of muslin, kept wet by means of a wick attached to it and dropping into the water in the reservoir. The muslin covering and the wick shall be suitable for the purpose, clean and free from size or grease. 3) No part of the wet-bulb shall be within 76 millimeter from the dry-bulb or less than 25 millimeter from the surface of the water in the reservoir and the water reservoir shall be below it, on the side of it away from the dry-bulb. 4) The bulb shall be spherical and or suitable dimensions and shall be freely exposed on all sides to the air of the room. 5) The bores of the stems shall be such that the position of the top of the mercury column shall be readily distinguishable at a distance of 60 centimeters. 6) Each thermometer shall be graduated so that accurate readings may be taken between 10 and 50 degrees centigrade. 7) Every degree from 10 degree upto 50 degrees shall be clearly marked by horizontal lines on the steam, each fifth degree; shall be marked by longer marks that the intermediates degrees and the temperature marked opposite each fifth degree, i.e. 10, 15, 20, 25, 30, 35, 40, 45, 50. 8) The markings as above shall be accurate, that is to say, at no temperature between 10 and 50 degrees, shall the indicated readings be in error by more that one ninth of a degree. 9) A distinctive number shall be indelibly marked upon the thermometer. 10) The accuracy of each thermometer shall be certified by the National Physical Laboratory, Delhi, or some competent authority appointed by the Chief Inspector of Factories and such certificate shall be attached to the humidity register. Rule 37. Thermometers to be maintained in efficient order – 26 Each thermometer shall be maintained at all times during the period of employment in efficient working order, so as to give accurate indications and in particular – a) the wick and the muslin covering of the wet-bulb shall be renewed once a week; b) the reservoir shall be filled with water which shall be completely renewed once a day. The Chief Inspector may direct the use of distilled water or pure rain water in any particular mill or mills in certain localities; and c) no water shall be applied directly to the sick or covering during the period of employment. Rule 38. Inaccurate thermometer not to be used without fresh certificate. If an Inspector gives notice in writing that a thermometer is not accurate, it shall not, after one month from the date of such notice, be deemed to be accurate unless and until it has been reexamined as prescribed and a fresh certificate obtained which shall be kept attached to the humidity register. Rule 39. Hygrometer not to be affixed to wall, etc, unless protected by wood. 1) No hygrometer shall be affixed to a wall, pillar, or other surface unless protected there from by wood or there non-conducting material at least 12 millimeter in thickness and distant at least 25 millimeter from the bulb of each thermometer. 2) No hygrometer shall be fixed at a height of more than 170 cm from the floor to the top of thermometer stem or in the direct draughts from a fan, window, or ventilating opening. Rule 40. No reading shall be taken for record on any hygrometer within 15 minutes of the renewal or water No reading shall be taken for record on any hygrometer within 15 minutes of the renewal or water in the reservoir. Rule 41. How to introduce steam for humidification :- In any room in which steam pipes are used for the introduction of steam for the purpose of artificial humidification of the air the following provisions shall apply: a) the diameter of such pipes shall not exceed 50 mm and in the case of pipes installed after 1st day of Jan.1960 the diameter shall not exceed 25 millimeter; b) such pipes shall be as short as is reasonably practicable. c) all hangers supporting such pipes shall be separated from the bare pipes by an efficient insulator not less than 15 mm in thickness: d) no uncovered jet from such pipe shall project more than 100 mm beyond the outer surface of any cover: e) the steam pressure shall be as low as practicable and shall not exceed 5 kg per square centimeter: and 27 f) the pipe employed for the introduction of steam into the air in a department shall be effectively covered with such non-conducting material, as may be approved by the Inspector in order to minimize the amount of heat radiated by them into the department. Rule 42. Lighting of Interior Parts - 1) The general illumination over those interior parts of a factory where persons are regularly employed shall be not less than 65 lux measures in the horizontal plane at a level of 90 centimeters above the floor: Provided that in any such parts in which the mounting height of the light source for general illumination necessarily exceeds 7.6 meters measured from the floor or where the structure or plant prevents the uniform attainment of this standard, the general illumination at the said level shall be not less than 22 lux and where work is actually being done the illumination shall be not less than 65 lux. 2) The illumination over all other interior parts of the factory over which persons employed pass shall, when and where a person is passing, be not less than 5 lux at floor level. 3) The standard specified in this rule shall be without prejudice to the provision of any additional illumination required to render the lighting sufficient and suitable for the nature of the work. Rule 43. Prevention of glare 1. Where any source of artificial light in the factory is less than 5 meter above floor level, no part of the light source or of the lighting fitting having a brightness greater than 5 lamberts shall be visible to persons whilst normally employed within 30 meters of the source, except where the angle of elevation from the eye to the source or part of the fitting as the case may be exceeds 20 degrees. 2. Any local light, that is to say an artificial light designed to illuminate particularly the area or part of the area of work of a single operative or small group of operatives working near each other, shall be provided with a suitable shade of opaque material to prevent glare or with other effective means by which the light source is completely screened from the eyes of every person employed at a normal working place, or shall be so placed that no such person is exposed to glare there from. Rule 44. Power of Chief Inspector to exempt- Where the Chief Inspector is satisfied in respect of any particular factory or part thereof or in respect of any description of workroom or process that any requirement of rules 42 and 43 is inappropriate or is not reasonably practicable, he may by order in writing exempt the factory or part thereof, or description of workroom or process from such requirement to such extent and subject to such conditions as he may specify. Rule 45. Exemption from Rule 42 Nothing in rule 42 shall apply to the parts of factories in which light sensitive photographic materials are made or used in an exposed condition or where such exposing portion are carried on. 28 Rule 46. Quantity of drinking water- The quantity of drinking water to be provided for the workers in every factory shall be at least 5 liters a day for each worker employed in the factory and such drinking water shall be readily available at all times during working hours. Rule 47. Source of water supply- The water provided for drinking shall be supplied a) from a public water-supply system, or b) from any other source approved in writing by the Health Officer or any other Officer appointed by the State Government in this regard. Rule 48. Means of supply If drinking water is not supplied directly from tape either connected with public water supply system or any other water supply system of the factory approved by the Health Officer or any other officer appointed by the state Government, it shall be kept in suitable vessels, receptacles or tanks fitted with taps and having dust proof covers, and placed on raised stands or platforms in shade and having suitable arrangement of drainage to carry away the spilled water. Such vessels, receptacles or tanks shall be kept clean and the water renewed at least once every day. All practicable measures shall be taken to ensure that the water is free from contamination. Rule 49. Cleanliness of well or reservoir 1. Drinking water shall not be supplied from any open well or reservoir unless it is so constructed, situated, protected and maintained as to be free from the possibility of pollution by chemical, or bacterial and extraneous impurities. 2. Where drinking water is supplied from such well or reservoir, the water in it shall be sterilized once a week or more frequently if the Inspector by written order so requires, and the date on which sterilizing is carried out shall be recorded; Provided that this requirement shall not apply to any such well or reservoir if the water therein is filtered and treated to the satisfaction of the Health Officer or other officers appointed by the State Government as the case may be. Rule 50. Report of Health Officer or other officers appointed by the State Government for this purpose The Inspector may, by order in writing direct the manager to obtain, at such time or at such intervals as he may direct, a report from the Health Officer or other officers appointed by the State Government as to the fitness for human consumption of the water supplied to the workers, and in every case to submit to the Inspector a copy of such report as soon as it is received from the Health Officer or the other officers appointed by the state Government for this purpose. 29 Rule 51. Cooling of water In every factory wherein more than two hundred and fifty workers are ordinarily employed: a) the drinking water supplied to the workers shall from the Ist April to the 31st September in every year, be cooled by ice or other effective method: Provided that if ice is placed in the drinking water, the ice shall be cleaned and wholesome and shall be obtained only from a source approved in writing by the Health Officer or other officer appointed by the State Government. b) the cooled drinking water shall be supplied in every canteen, lunchroom and rest room and also at conveniently accessible points throughout the factory which for the purpose of these rules shall be called ‘Water Centers’: c) the water centers shall be sheltered from the weather and adequately drained: d) the number of water centers to be provided shall be one “center” for every 150 persons or part thereof employed at any one time in the factory : Provided that in the case of a factory where the number of persons employed exceed 500, it shall be sufficient if there is one such “center” as aforesaid for every 150 person up to the first 500 and one for every 500 persons thereafter: Provided further that the distance between the place of work of any worker shall not be more than 50 meters from the nearest water center or any distance as may be specified by the Inspector. i) every water center shall be maintained in a clean an orderly condition : ii) the means of supply of cooled drinking water shall be either directly through taps connected to water coolers or any other system for cooling of water, or by means of vessels, receptacles or tanks fitted with taps and having dust proof covers and placed on raised stands or platforms in shade, and having suitable arrangement of drainage to carry away the spilt water. Such vessels, receptacles or tanks shall be kept clean and the water renewed at least once every day : and iii) every water center shall be in charge of a suitable person who shall distribute the water. Such person shall be provided with clean cloths while on duty. Provided that the Chief Inspector may exempt any “water center” from the requirements of this clause. Provided further that this clause shall not apply to any factory in which suitable mechanically operated drinking water refrigerating units are installed to the satisfaction of the Chief Inspector. Rule 52. Latrine accommodation Latrine accommodation shall be provided in every factory on the following scale : a) where females are employed, there shall be at least one latrine for every 25 females : b) where males are employed, there shall be at least one latrine for every 25 males. Provided that where the number of males exceeds 100, it shall be sufficient if there is one latrine seat for every 25 males up to the first 100, and one for every 50 thereafter. In calculating the number of latrine required under this rule, any odd number of workers less than 25, or 50, as the case may be, shall be reckoned as 25 or 50. 30 (c) Sanitary Napkins of adequate quantity, conforming to Indian Standards shall be provided and maintained in the female toilets for their use, and the same replenished on daily basis;1 (d) disposable bins with lids shall be provided within the women’s toilets for the collection of the used napkins. The used napkins shall be disposed off as per the procedure approved by the Chief Inspector, by order.1 Rule 53. Latrines to conform to public health requirements- Latrines, other than those connected with an efficient water-borne sewage System, shall comply with the requirements of the public Health authorities. Rule 54. Privacy of latrines- Every latrine shall be under cover and every seat in the latrine shall be so Partitioned off as to secure privacy, and each partitioned shall have a proper door and fastenings. Rule 55. Sign Boards to be displayed- Where workers of both sexes are employed, there shall be displayed outside each latrine block a notice “For Men Only” or “For Women Only” as the case may be, in the language understood by the majority of the workers. The notice shall also bear the figure of a man or of a woman as the case may be. Rule 56. Urinal accommodation- 1. Urinal accommodation shall be provided for the use of workers and shall not be less than 60 centimeters in length for every 50 workers. Provided that, where the number of workers employed exceeds 500, it shall be sufficient if there is one urinal for every 50 workers up to the first 500 employed and one for every 100 thereafter. Where women are employed, separate urinal accommodation shall be provided for them on the same scale as mentioned above : Provided further that the Chief Inspector may by order in writing exempt, subject to such conditions as he may think fit to impose, small factories employing less than 20 workers from the provisions of separate urinal accommodation if he is satisfied that the latrine accommodation in such factories is sufficient and suitable. 2. In calculating the urinal accommodation required under sub-rule (1), any odd number of workers less than 50 or 100, as the case may be, shall be reckoned as 50 or 100, and the maximum number of persons working in the factory, at any time and not the total number of persons employed in the factory, shall be taken into account. Rule 57. Urinals to conform to public health requirements- Urinals, other than those connected with an efficient water-borne sewage system, and urinals in a factory wherein more than two hundred and fifty workers are ordinarily employed shall comply with the requirements of the Public Health authorities. 1Sixth Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/595 dtd., 12.06.2019. Rule 58. Certain latrines and urinals to be connected to sewage system- When any general system of underground sewerage with an assured water supply for any particular locality is provided in a municipality, all latrines and urinals other than septic tank latrine and any other type of latrines and urinals to be approved for this purpose by the public Health authority, of a factory situated in such locality shall, if the factory is situated with 30 meters of an existing sewer, be connected with that sewage system. 31 1 Rule 59. Deleted. Rule 60. Construction and maintenance of drains- All drains carrying waste or sullage water shall be constructed in masonry or other impermeable material and shall be regularly flushed and the effluent disposed of by connecting such drains with a suitable drainage line. Provided that where there is no such drainage line, the effluent shall be deodorized and rendered innocuous and then disposed of in a suitable manner to the satisfaction of the Health Officer. Rule 61. Water taps in latrines- 1) Where piped water supply is available, a sufficient number of water taps, conveniently accessible, shall be provided in or near such latrine accommodation. 2) If piped water supply is not available, sufficient quantity of water shall be kept stored in suitable receptacles near the latrines. Rule 61. (A) Number of Sweepers- In every factory employing number of workers in any shifts as shown in column # 2 of the schedule appended hereto, there shall be employed at least a number of full time/part time sweepers as shown in column # 3 of the said schedule in the respective shift to clean the latrines, urinals and wash places provided in the factory for the use of the workers employed in that shift, in order to maintain the same in clean and sanitary condition at all times. Schedule Serial No of workers in the shift No of sweepers to be the shift employed in 1. Up to 100 1 part time 2. Above 100 but not above 250 1 full time 3. Above 250 but not above 500 2 full time 4. Above 500 but not above 1000 3 full time 32 __________________________________________________________________________ 1Eleventh Amendment vide No.F.7(121)-FB/AM(Vol.-II)/2007/1058-68 dtd., 13.09.2022. 5. Above 1000 3 full time plus one full time for every additional 500 or part thereof. Rule 62. Provision of towel and soap in the latrines and urinals- Sufficient number of towels and soaps shall be provided as to the satisfaction of the Inspector. Rule 63. Exemption The Chief Inspector may exempt the factories declared under section 85 form the provisions of Rules 52 to 62 provided he is satisfied that there are alternative arrangements for meeting the requirements of latrines and urinals. Provided further that the Chief Inspector may exempt any other class of factories employing less than 20 workers which are already in existence on the date of application of these rules from the provisions of the rules 52 to 62 on being satisfied about other suitable arrangements. Rule 64. Number and location of spittoons- The number and location of the spittoons to be provided shall be to the satisfaction of the Inspector. Rule 65. Type of spittoons- The spittoons shall be of any of the following types : a) a galvanized iron container with a conical funnel-shaped cover. A layer of suitable disinfectant liquid shall always be maintained in the containers. b) a container filled with dry, clean sand, and covered with a layer of bleaching powder ; or c) any other type approved by the Chief Inspector. Rule 66. Cleaning of spittoons The spittoon mentioned in clause (a) of rule 65 shall be emptied, cleaned and disinfected at least once every day ; and the spittoon mentioned in clause (b) of rule 65 shall be cleaned by scrapping out the top layer of sand as often as necessary or at least once every day. 33 Chapter IV Rule Description Rule 67 Further Safety precautions Schedule I Textile Machinery except Machinery used in Jute Mills. Schedule II Jute Mill Schedule III Cotton Ginning Machinery Schedule IV Wood Working Machinery Schedule V Rubber Mills and Plastic Mills Schedule VI Centrifugal Machines Schedule VII Power press Schedule VIII Shears, Slitters and Guillotine Machines Schedule IX Agitators and Mixing Machines Schedule X Leather, Plastic and Rubber Stripper Machines Schedule XI Special Rule for Printing Presses Schedule XII All factories Rule 68 Register of workers employed for work on or near machinery in motion Rule 69 Tight fitting clothing Rule 70 All Belts etc. to be examined regularly Rule 71 Employment of young persons on dangerous machines Rule 72 Hoists and Lifts Rule 73 Lifting machines, chains, ropes and lifting tackles Rule 74 Pressure vessels or plant Rule 75 Water-sealed gasholder Rule 76 Excessive weights Rule 77 Protection of eyes Schedule I Risk of injury to eyes from particles Schedule II Risk of injury to eyes by reason of exposure to excessive light Rule 78 Minimum dimensions of man-holes Rule 79 Exemptions. The requirements of sub-section (4) of section 37 shall not apply to the following processes carried on in any Factory Rule 80 Fire protection Rule 81 Means of Escape for Cotton Ginning Factories Rule 82 Fire-fighting apparatus and water supply Rule 83 Ladders Rule 84 Protection of workers attending to prime movers Rule 85 Polymerizing or Curing Machine Rule 86 Safety Measure in Factories where Equipments of Pipelines containing Inflammable Materials are Operated Rule 87 Safety Measure in Gas Works Rule 88 Fragile Roofs-provision of Crawling Boards etc. Rule 89 Special Safety Precautions for Certain Highly Hazardous Chemical Process Rule 90 Planting of Trees Rule 91 Hand Protection Rule 92 Head Protection Rule 92A Protective equipment Rule 93 Provision of Safety Belts and Life-lines Rule 94 Ovens and Driers 34 Rule 95 Reaction vessels and kettles Rule 96 Examination of eye sight of certain workers Rule 97 Railways in factories Rule 98 Safety Committee Rule 99 Site Appraisal Committee Rule 100 Health and Safety Policy Rule 101 Collection And Development And Dissemination of Information (Rules made under Sec 41B and 112, Material Safety Date Sheet) Rule 102 Disclosure Of Information Of Workers Rule 103 Disclosure Of Information To The Chief Inspector Rule 104 Information On Industrial Wastes Rule 105 Review Of The Information Furnished To Workers Etc Rule 106 Confidentiality Of Information Rule 107 Medical Examination Rule 108 Occupational Health Centres Rule 109 Ambulance Van Rule 110 Decontamination Facilities Rule 111 Making Available Health Records To Workers Rule 112 Ambulance Van Rule 113 Issue Of Guidelines Rule 114 Quality of personal protective equipment Rule 115 Protective equipment Rule 116 Thermic Fluid Heaters Rule 67. Further Safety precautions. Without prejudice to the provisions of sub-section (i) of section 21 in regard to the fencing of machines, further precautions specified in the schedules annexed hereto shall apply to the machines noted in each schedule. Schedule 1 Textile Machinery except Machinery used in Jute Mills. 1. Application – The requirement of this schedule shall apply to machinery in factories engaged in the manufacture or processing of textiles other than jute textiles. 2. Definitions – For the purposes of this schedule- a) “Calendar” means a set of heavy rollers mounted on vertical side frames and arranged to pass cloth between them. Calendars may have two to ten rollers, or howls, some of which can be heated. b) “Embossing calendar” means a calendar with two or more rolls, one of which is engraved for producing figure effects of various kinds on a fabric. c) “Card” means a machine consisting of cylinders of various sizes – and in certain cases flats – covered with card clothing and set in relation to each so that fibers in staple form may be separated into individual relationship. The speed of the cylinders and their direction of rotation varies. The finished product is delivered as a silver. Cards of different types are : the revolving flat card, the roller and clearer card, etc. d) “Card Clothing” means the material with which the surfaces of the cylinder, doffer, flats, etc. of a card are covered and consists of a thick 35 foundation material made of, either textile fabrics through which are pressed many fine closely spaced, specially bent wires, or mounted saw toothed wire. e) “Comber” means a machine for combining fibers of cotton, wool, etc. The essential parts are device for feeding forward a fringe of fibers at regular intervals and an arrangement of combs or pins, which, at the right time, pass through the fringe. All tangled fibres, ahort fibres, and nips are removed and the long fibres are laid parallel. f) “combing machinery” means a general classification of machinery including combers, sliver lap machines, ribbon lap machines, and gill boxes, but excluding cards. g) “Rotary staple Cutter” means a machine consisting of one or more rotary blades used for the purpose of cutting textile fibres into staple lengths. h) “Garnett machine” means any of a number of types of machines for opening hard twisted waste of wool, cotton, silk, etc. Essentially, such machines consist of a licker-in ; one or more cylinders, each having a competent worker and stripper rolls; and a fency roll and doffer. The action of such machines is somewhat like that a wool card, but it is much more severe in that the various rolls are covered with garnett wire instead of card clothing. i) “Gill Box” means a machine used in the worsted system of system of manufacturing yarns. Its function is to arrange fibres in parallel order. Essentially, it consists of a pair of freed rolls and a series of followers where the followers move at a faster surface speed and perform a combing action. j) “In-funning rolls” means any pair of rolls or drums between which there is a “nip”. k) “Interlocking arrangement” means a device that prevents the setting in motion of a dangerous part of a machine or the machine itself while the guard cover or door provided to safeguard against danger is open or unlocked, and which will also hold the guard, cover or door closed and locked while the machine or the dangerous part is in motion. l) “kier” means a large metal vat, usually a pressure type, in which fabrics may be boiled out, bleached, etc. m) “Ribbon lapper” means a machine or a part of a machine used to prepare laps for feeding a cotton comb ; its purpose is to provide a uniform lap in which the fibres have straightened as much as possible. n) “Silver lapper” means a machine or a part of a machine in which a number of parallel card slivers are drafted slightly, laid side by side in a compact sheet, and wound into a cylindrical package. o) “Loom” means a machine for effecting the interlocking of two series of yarns crossing one another at right angles. The warp yarns are wound on a warp beam and pass through headless and reeds. The filling is shot across in a shuttle and settled in place by reeds and slay and the fabric is wound on a cloth beam. p) “Starch mangle” means a mangle that is used specifically for starching cotton goods. It commonly consists of two large rolls and a shallow open vat with several immersion rolls. The vat contains the starch solution. q) “Water mangle” means a calendar having two or more rolls used for squeezing water from fabrics before drying. Water mangles also may be used in other ways during the finishing of various fabrics. 36 r) “Mule” means a type of spinning frame having a head stock and a carriage as its two main sections. The head stock is stationary. The carriage is movable and it carries the spindles which draft and spin the roving into yarn. The carriage extends over the whole width of the machine and moves slowly toward and away from the head stock during the spinning operation. s) “Nip” is the danger zone between two rolls or drums which by virtue of their positioning and movement create a nipping hazard. t) “Openers and Pickers” means a general classification of machinery which includes breaker pickers, intermediate pickers, finisher pickers, single process pickers, multiple process pickers, willow machines, card and picker waste cleaners, thread extractors, shredding machines, roving waste openers, shoddy pickers, bale breakers, feeders, vertical openers, lattice cleaners, horizontal cleaners, and any similar machinery equipped with either cylinders, screen section, calendar section, rolls, or beaters used for the preparation of stock for further processing. u) “Paddler” means a through for a solution and two or more squeeze rolls between which cloth passes after being passed through a mordant or dye bath. v) “Plaiting machine” means a machine used to lay cloth into folds of regular length for convenience of subsequent process or use. w) “Roller printing machine” means a machine consisting of large central cylinder, or pressure bowl, around the lower part of the perimeter of which is placed a series of engraved color rollers (each having a color through), a furnisher roller, doctor blades, etc. The machine is used for printing fabrics. x) “Continuous bleaching range” means a machine for bleaching of cloth in rope or open-width form with the following arrangement. The cloth, after wetting out, pass through a squeeze roll into a saturator containing a solution of caustic soda and then to and enclosed J-Box. A V-shaped arrangement is attached to the front part of the J. Box for uniform and rapid saturation of the cloth with steam before it is packed down in the J- Box. The cloth, in a single strand rope form, passes over a guide roll down the first arm of the “V” and up the second. Steam is injected into the “V” at the upper end of the second arm so that the cloth is rapidly saturated with steam, at this point. The J-Box capacity is such that cloth will remain hot for a sufficient time to complete the scouring action. It then passes series of washers with a squeeze roll in between. The cloth then passes through a second set of saturator, J-Box and washer, where it is treated with the peroxide solution. By slight modification of the form of the unit, the same process can be applied to open-width cloth. y) “Mercerizing range” means a 3-bowl mangle, a tenter frame, and a number of boxes for washing a scouring. The whole set up is in a straight line and all parts operate continuously. The combination is used to saturate the cloth with sodium hydroxide, stretch it while saturated, and washing out most of the caustic before releasing tension. z) “Sanforizing machine” means a machine consisting of a large steam- heated cylinder, and endless, thick, wollen felt blanket which is in close contact with the cylinder for most of its perimeter, and an electrically heated shoe which presses the cloth against the blanket while the latter is in a stretched condition as it curves around feed-in roll. 37 aa) “Shearing machine” means a machine used for shearing cloth. Cutting action is provided by a number of steel blades spirally mounted on a roller. The roller rotates in close contact with a fixed ledger blade. There may be form one to six such rollers on a machine. bb) “Singeing machine” means a machine which comprises of a heated roller, plate, or an open gas flame. The cloth or yarn is rapidly passed over the roller or the plate or through the open gas flame to remove fuzz or hairiness by burning. cc) “Slasher” means a machine used for applying a size mixture to wrap yarns. Essentially, it consists of a stand for holding section beams, a size box, one or more cylindrical dryers or an enclosed hot air dryer, and a beaming end for winding the yarn on the loom beams. dd) “Tenter frame” means a machine for drying cloth under tension. It essentially consists of a pair of endless traveling chains fitted with clips of fine pins and carried on tracks. The cloth is firmly held at the salvages by the two chains which diverge as they move forward so that the cloth is brought to the desired width. ee) “Warper” means a machine for preparing and arranging the yarns intended for the warp of a fabric, specifically, a beam warper. 3. General safety requirements. 1) Every textile machine shall be provided with individual mechanical or electrical means for starting and stopping such machines. Belt shifter on machines driven by belts and shafting should be provided with a belt shifter lock of an equivalent positive locking device. 2) Stopping and starting handles or other controls shall be of such design and so positioned as to prevent the operator’s hand or fingers from striking against any moving part of any other part of the machine. 3) All belts, pulleys, gears, chains, sprocket wheels, and other dangerous moving parts of machinery which either form part of the machinery or are used in association with it, shall be securely guarded. 4. Openers and pickers. 1) In all opening or picker machinery, beaters and other dangerous parts shall be securely fenced to suitable guards so as to prevent contact with them. Such guards and doors or covers or openings giving access to any dangerous part of the machinery shall be provided with interlocking arrangement. Provided that in the case of doors or covers of openings givings access to any dangerous part, other than beater covers, instead of the interlocking arrangement, such openings may be so fenced by guards which prevent access to any such dangerous part and which is either kept positively locked in position or fixed in such a manner that it cannot be removed without the use of hand tools. 2) The feed rolls on all opening and picking machinery shall be covered with a guard designed to prevent the operator from reaching the nip while the machinery is in operation. 3) The lap forming rollers shall be fitted with a guard or cover which shall prevent access to the nip at the intake of the lap roller and fluted roller as long as the weighted rack is down. The Guard or cover shall be so locked that it cannot be raised until the machine is stopped, and the machine cannot be started until the cover or guard is closed. 38 Provided that the foregoing provision shall not apply to the machines equipped with automatic lap forming devices. Provided further any such machine equipped with an automatic lap forming device shall not be used unless the automatic lap forming device is in efficient working order. 5. Cotton cards. 1) All cylinder doors shall be secured by interlocking arrangement which shall prevent the door being opened until the cylinder has ceased to revolve and shall render it impossible to restart the machine until the door has been closed. Provided that the latter requirement in respect of the automatic locking device shall not apply while stripping or grinding operations are carried out; Provided further that stripping or grinding operations shall be carried out only by specially trained adult workers wearing tight fitting clothing whose names have been recorded in the register in Form 12 prescribed in this behalf as required in subsection (1) of section 22. 2) The licker-in shall be guarded so as to prevent access to the dangerous parts. 3) Every card shall be equipped with an arrangement that would enable the card cylinder to be driven by power during stripping/grinding operations without having to either shift the main belt to the fast pulley of the machine or to dismantle the interlocking mechanism. Such an arrangement shall be used only for stripping or grinding operations. 6. Garnett machines. 1) Garnett licker-ins shall be enclosed. 2) Garnett fancy rolls shall be enclosed by guards. Those shall be installed in a way that keeps worker rolls reasonably accessible for removal or adjustment. 3) The underside of the garnett shall be guarded by a screen mesh or other form of enclosures to prevent access. 7. Gill boxes. 1) The feed end shall be guarded so as to prevent fingers being caught in the pins of the intersecting fallers. 2) All nips of in-running rolls shall be guarded by suitable nip guards conforming to the following specifications:- Any opening which the guard may permit when fitted in position shall be so restricted with respect to the distance of the opening from any nip point through that opening and in any circumstances the maximum width of the opening shall not exceed the following: Distance of opening from nip point Maximum width of opening 0 to 30 mm 6 mm 39 to 63 mm 10 mm 64 to 88 mm 13 mm 89 to 140 mm 15 mm 141 to 165 mm 19 mm 166 to 190 mm 22 mm 191 to 215 mm 32 mm 8. Silver and ribbon lappers (cotton). The calendar drums and the lap spool shall be provided with a guard to prevent access to the nip between the in-running rolls. 39 9. Speed frames. Jack box wheels at the head stock shall be guarded and the guard shall Have interlocking arrangement. 10. Spinning mules. Wheels on spinning mule carriages shall be provided with substantial wheel guards, extending to within 6 mm of the rails. 11. Warpers. Swiveled double-bar gates shall be installed on all warpers operating in excess of 410 meters/min. These gates shall have interlocking arrangement, except for the purpose of inching or jogging. Provided that the top and bottom bars of the gate shall be at least 1.05 and 0.53 meters high from the floor or working platform, and the gate shall be located 38 mm from the vertical tangement to the beam head. 12. Slashers. 1) Cylinder dryers. a) All open nips of in-running rolls shall be guarded by nip guards conforming to the requirements in paragraph 7. b) When slashers are operated by control levers, therse levers, shall be connected to a horizontal bar or treadle located not more than 170 cm. above the floor to control the operation from any point. c) Slashers operated by push-button control shall have stop and start buttons located at each end of the machine and additional stop and start buttons located on both sides of the machines at intervals spaced not more than 1.83 meters on centers. 13. Looms. 1) Each loom shall be equipped with suitable guards designed to minimize the danger from flying shuttles. 2) Beam weights for tension in beam shall be of such construction so as to prevent it falling during its adjustment. 14. Valves of kiers, tanks, and other containers. 1) Each valve controlling the flow of steam, injurious gases or liquids into a kier or any other tank or container into which a person in likely to enter in connection with a precess, operation, maintenance or for any other purpose, shall be provided with a suitable locking arrangement to enable the said person to lock the valve securely in the closed position and retain the key with him before entering the kier, tank or container. 2) Wherever boiling tanks, caustic tanks and any other containers from which liquids which are hot, corrosive or toxic may overflow of splash, are so located that the operator cannot see the contents from the floor or working area emergency shut off valves which can be controlled from a point not subject to danger of splash shall be provided to prevent danger. 15. Shearing machines: All revolving blades on shearing machines shall be guarded so that the opening between the cloth surface and the bottom of the guard will not exceed 10 mm. 16. Continuous bleaching range (cotton and rayon). The nip of all in-running rolls on open-width bleaching machine rolls shall be protected with a guard to prevent the worker from being caught at the nip. The guard shall extend across the entire length of the nip. 17. Mercerizing range (piece goods). 1) A stopping device shall be provided at each end of the machine. 2) A guard shall be provided at each end of the frame between the in-running chain and the clip opener. 40 3) A nip guard shall be provided for the in-running rolls of the mangle and washers and the guard shall conform to the requirements in paragraph 7 (2). 18. Tender frames. 1) A stopping device shall be provided at each end of the machine. 2) A guard shall be provided at each end of the machine frame at the in- running chain and clip opener. 19. Paddlers. Suitable nip guards conforming to the requirement in paragraph 7(2) shall be provided to all dangerous in-running rolls. 20. Centrifugal extractors. 1) Each extractor shall be provided with a guard for the basket, and the guard shall have inter-locking arrangement. 2) Each extractor shall be equipped with a mechanically or electrically operated brake to quickly stop the basket when the power driving the basket is shut off. 21. Squeezer or wringer extractor, water mangle, strach mangle, back washer (worsted yarn), crabbing machines and decating machine-All in-running rolls shall be guarded with nip guards conforming to the requirements in paragraph 7(2). 22. Sanforizing and palmer machine. 1) Nip guards shall be provided on all accessible in-running rolls and these shall conform to the requirements in paragraph 7(2). 2) Access from the sides to the nips of in-running rolls should be fenced by suitable side guards. 3) A safety trip rod, cable or wire center cord shall be provided across the front and back of all palmer cylinders extending the length of the face of the cylinder. It shall operate readily whether pushed or pulled. The safety trip shall not be more than 170 cm above the level at which the operator stands and shall be readily accessible. 23. Rope washers. 1) Splash guards shall be installed on all rope washers unless the machine is so designed as to prevent the water or liquid from splashing the operator, the floor, or working surface. 2) A safety trip rod, cable or wire centre cord shall be provided across the front and back of all rope washers extending the length of the face of the washer. It shall operate readily whether pushed or pulled. This safety trip shall be not more than 170 cm. above the level on which the operator stands and shall be readily accessible. 24. Laundry washer tumbler or shaker. 1) Each drying tumbler, each double cylinder shaker or clothes tumbler and each washing machine shall be equipped with an inter-locking arrangement which will prevent the power operation of the inside cylinder when the outer door on the case or shell is open, and which will also prevent the outer door on the case or shell from being opened without shutting off the power and the cylinder coming to a stop. This should not prevent the movement of the inner cylinder by means of a hand operated mechanism or an inching device. 2) Each closed barrel shall also be equipped with adequate means for holding open doors or covers of the inner and outer cylinders of shells while it is being loaded or unloaded. 41 25. Printing machine (roller type). 1) All in-running rolls shall be guarded by nip guards conforming to the requirement in paragraph 7(2). 2) The engraved roller gears and the large crown wheel shall be guarded. 26. Calenders. The nip at the in-running side of the rolls shall be provided with a guard extending across the entire length of the nip and arranged to prevent the fingers of the workers from being pulled in between the rolls or between the guard and the rolls, and so constructed that the cloth can be fed into the rolls safely. 27. Rotary staple cutters. The cutter shall be protected by a guard to prevent hands reaching the cutting zone. 28. Plaiting machines. Access to the trap between the knife and card bar shall be prevented by a guard. 29. Hand baling machine. An angle iron handle-stop guard shall be installed at right angle to the frame of the machine. The stop guard shall be so designed and so located that it will prevent the handle from traveling beyond the vertical position should the handle slip from the operator’s hand when the pawl has been released from the teeth of the take-up gear. 30. Flat-work ironer. Each flat-work or collar ironer shall be equipped with a safety bar or other guard across the entire front of the feed or first pressure rolls so arranged that the striking of the bar or guard by the hand of the operator or other person will stop the machine. The guard shall be such that the operator or other person cannot reach into the rolls without removing the guard. This may be either a vertical guard on all sides or a complete cover. If a vertical guard is used, the distance from the floor or working platform to the top of guard shall be not less than 1.83 meters. Schedule – II JUTE MILL 1. Fencing of Machinery. Fencings, guards or safety devices in respect of each individual machine as prescribed shall be provided and maintained in good order. 2. Softening Machine. a) A safety stopping device comprising or a breast plate in front of the feed table shall be provided to operate the belt striking gear by releasing an unbalanced weight. No device departing from the unbalanced weight principle will be deemed to conform to this rule unless it has been approved in writing by the inspector. In the case of machines provided with an individual electric drive the device shall be arranged to act on a switch inserted in the no-volt release circuit. b) The feed table shall not be less than 1.83 meters in length, measured from the centre of the first cloth roller to the centre of the first pair of cast iron rollers. The table shall be provided with side guards reaching a height of not less than 1.37 meters from the floor, and extending at that height, not less than 1.07 meters from the centre of the first pair of rollers; the height of the rest of the side guards shall not be less than 1.22 meters from the floor. c) The starting and stopping gear shall be arranged to comply with the following :- i) Provision for stopping the machine at both the feed and delivery ends. 42 ii) Provision for starting the machine at the feed end only, the design shall be such that an operator at the feed and cannot start the machine without the co-operation of an operator at the delivery end. iii) When a machine is stopped for clearing a jam or attention otherwise, the starting gear shall be secured in the “Off” position at least by a lock operated by a removable key in possession of the person attending the machine. iv) The lever operating the unbalanced weight shall be securely fenced. d) Sheet steel casings completely enclosing the side shafts, i.e. , the shafts and gears shall not be exposed on the underside. The casings shall be locked or secured by a device which will ensure i) that they cannot be opened while the machine is in motion and ii) that it will not be possible to start the machine unless they are closed. 3. Carding machines: a) The underframe shall be guarded in such a manner that it will not be possible for operators to obtain access underneath the machine until the cylinder has ceased to revolve. The lowest cross member of the frame shall come down to point not more than 25.4 cm from the floor and all openings above this, large enough to permit of access underneath, shall be filled in with sheet steel or fitted with bars or rods spaced not more than 15.24 cm apart, any part of this controlled by a device which will ensure they can not be opened until the cylinder has come to rest and that the machine cannot be restarted until the doors are closed : Provided that in the case of machines installed before 1st January 1950, rigidly secured panels filling the under-frame will be deemed to comply with it. b) A guard with panels and sliding doors of sheet steel or closely spaced bars or rods enclosing the side gears; there shall be no opening at the underside of this protection for access to the gears. The sliding doors shall be controlled by a device which will ensure that they cannot be opened until the cylinder has come to rest, and that the machine cannot be started up until the doors are closed. c) A sheet steel guard extending upto the centre line of the cylinder, enclosing the stripper belts and pulleys shall be provided on all machines installed after 1st January, 1950. d) An adequately strong and rigid set of bars or rods over the doffer roller, shall be securely bolted in position. This guard must follow the radius of the roller; the space between the rods not to exceed 5.08 cm; the distance from the doffer pin points to the underside of the rods to be 10.16 cm; the space between the drawing pressing roller and the first rod not to exceed 5.08 cm; and the width of the guard from the first to the last rod to be not less than 30.5 cm. e) A hard or guard rail extending the full width of the Drawing pressing roller, fitted in a convenient position in front of and higher than the roller. f) Effective side guards to prevent operator’s fingers being caught between the delivery roller and the pressing ball. g) When a machine is stopped for clearing a jam or attention otherwise, the starting gear shall be secured in the “Off” position atleast by a lock operated by a removable key in possession of the person attending the machine. 4. Drawing machine. 43 a) A sheet steel guard completely closing the space between the bend rail and the bottom of the retaining roller, the opening and closing of which shall be controlled by the starting gear, and the design such that the guard cannot be opened while the machine is running. The guard plate shall swivel more or less about the centre of its height, and the top edge shall swing inwards towards the gill bars as guard opens, and outwards as the guard closes : Provided further that in the case of machines with individual electric drive it will be sufficient if the guard is of the swiveling type and interlinked with the driving mechanism so that silver cannot be fed into the gills, or the guard opened, before the machine is stopped , and that the machine cannot be started up unless the guard is closed. b) Sheet steel or cast iron guards completely enclosing the end gears, the design to be such that access to the gears is possible only by removing the guard in its entirety. If doors or movable panels are provided they shall be controlled by a locking device, operated by the starting gear, which will ensure that the machine cannot be started unless the guard is completely closed and that no movable part cannot be opened whilst the machine is in motion; Provided that in the case of machines installed before Ist Jan., 1950, a guard securely held in position by automatic catches to prevent opening by vibration but without the interlocking arrangement will be deemed to comply with it. c) An efficient guard shall be provided which will prevent operator fingers or hands being caught between the delivery roller and the pressing ball. d) Starting and stopping gear so designed that the machine can be stopped by operatives on the feed and delivery sides; can be started only by an operative on the feed side but with the cooperation of the operative on the delivery side and cannot be started by an operative on the delivery side. The device necessitating cooperation shall be engaged before the machine stops. e) Shear pins driving the individual carriages shall be fitted to the pinion on the main back shaft and not to the pinion on the carriage back shaft. 5. Roving machine. a) Starting and stopping gear shall be designed to embody the following : i) Provision for stopping the machine on both the feed and delivery side. ii) Provision for starting the machine on the delivery side only. iii) A device on the delivery side which will automatically lock the belt striking gear in the “Off” position. This device shall be such that the machine will not stop before the lock is engaged nor start before it is disengaged by a worker on the delivery side. b) Sheet steel or cast iron guards completely enclosing the end gears, the design to be such that access to the gears is possible only by removing the guard in its entirety. If doors or movable panels are provided, they shall be controlled by a locking device, operated by the starting gear, which will ensure that the machine cannot be started unless the guard is completely closed land that no movable part can be opened whilst the machine is in motion : Provided that in the case of machines installed before Ist Jan., 1950, a guard securely held in position by automatic catches to prevent opening by 44 vibration, but without the interlocking arrangement will be deemed to comply with it. c) Shear pins driving individual carriages shall be fitted to the pinion on the main back shaft and not to the pinion on the carriage back shaft. 6. Spinning frames. a) Access between the driving cylinders whilst in motion shall be prevented by providing a door at the pass end, so interconnected with the starting gear that neither side of the frame can be set in motion whilst the door is open and conversely the door cannot be opened whilst either or both sides of the frame is or are running. Provided that in the case of machines installed before Ist Jan.,1950, hinged and will secured doors will be deemed to comply with it. b) Sheet steel or cast iron guards completely enclosing the end gear, the design to be such that access to the gears is possible only by removing the guard in its entirely; If doors or movable panels are provided they shall be controlled by a locking device, operated by the starting gear, which will ensure that the machine cannot be started unless the guard is completely closed and that no movable part can be open whilst the machine is in motion : Provided that in the case of machine installed before 1st Jan., 1950, a guard securely held in position by automatic catches to prevent opening by vibration but without the interlocking arrangement will be deemed to comply with it. 7. Cop Winding machines : a) Effective guards covering the driving end gears. Hinged doors or panels will not be deemed to comply with this rule unless securely held in the closed position by automatic catches to prevent opening by vibration. b) Guards covering the spindle driving gears of such designs that it will not be possible to remove them from position whilst the machine is in motion :Provided that in the case of machines installed before Ist Jan., 1950, guards rigidly secured by bolts or screws will be deemed to comply with it. 8. Roll winding machines : Effective guards for traverse or other gears and cams. Hinged doors or panels will not be deemed to comply with this rule unless securely held in the closed position by automatic catches to prevent opening by vibration. 9. Beaming machines : a) The flywheel shall be of the disc type. b) Cross and side shafts driving the starch rollers shall be enclosed in protecting tubes. c) A guard securely anchored in position and protecting the nip between the top and bottom starch rollers. It shall have an aperture large enough to pass the yarn through but not the operator’s hand. A hinged guard will not be deemed to be compliance with this rule. d) A guard protecting the nip between the yarn beam pressing roller and the outer top weight roller, i.e. the top weight roller on the side at which the beam is inserted and removed. e) The space between an yarn guide roller and its adjacent steam cylinder must be not less than 7.62 cm. 10. Looms : a) Sheet steel or cast iron for guards protecting the crank and wiper shaft spur gears shall be provided. 45 b) The minimum clearance between the sley and breast beam shall be not less than 5.08 cm. c) Yarn beams shall be placed on looms by mechanical or other means. Lifting into position by hand alone will not be deemed to comply with this rule. 11. Cropping machines : Sheet steel guards protecting the spirals shall be provided. 12. Calendaring machines : a) A strong and rigid guard securely fixed in position, in front of the nip between the bottom cast iron roller and the paper roller on top of same. This guard shall be constructed in such a manner that it will be impossible for the fingers of an operator to reach the nip through the aperture in the guard. b) Safety rollers protecting the nip of the upper rollers : These rollers must be made of steel or wrought iron tube, as light as possible and not more than 6.35 cm in external diameter. The safety roller shall ride on the under roller and be free to lift. It shall be set in such a manner that the peripheral clearance between it and the upper roller, and between it and the under roller when the safety roller is fully raised, will not permit of an operator’s fingers reaching the nip. c) Sheet steel panels shall be fitted on the machine gable to prevent access through same to the large wheel. d) Lever weights shall be lowered into strong and rigid guards. 13. Cloth cutting machines: A guard preventing access to the knife from the front, top or sides shall be provided. On the underside the knife shall be protected up to the maximum limit without interfering with the machine operation. 14. Lapping machines : a) Provision for starting the machine at the feed end only : the design shall be such that an operator at the feed end cannot start the machine without the co-operation of an operator at the delivery end and that he cannot interfere with the device necessitating co-operation. b) A “sight panel” fitted to the feed table in such position that operators on either side of the machine can see through to the other side. c) The hand wheel on the driving shaft shall be of the disc type and it shall be located at sufficient distance from the machine gable to permit of fencing being constructed between it and the lever mechanism operating the folder. d) The treadle mechanism shall be such as to allow extraction of the maximum cloth lapped and no worker shall be required to go up on the machine table to force it down. 15. Sewing machines: An apron plate shall be fitted in front of the feed chain and the plate shall be without holes or openings except for slots for the jocky pulleys. 16. Press pits : When the press table is level with the floor the clearance between it and the floor shall not be less than 10.16 cm. Schedule III Cotton Ginning Machinery 1. The line shaft or second motion in cotton ginning factories when below floor level, shall be completely enclosed by a continuous wall or unclimbable fencing with only so many openings as are necessary for access to the shaft for removing 46 cotton seed, cleaning and oiling, and such openings shall be provided with gates or doors, which shall be kept closed and locked. 2. The bars portions of the line shaft between the bearings and also of the projection at the ends of the line shaft shall be provided with adequate inverted “U” or sleeve type of guards of substantial construction. Schedule IV Wood Working Machinery 1. Definitions.- For the purposes of this schedule- a) “Wood working machine” means a circular saw, band saw, planning machine, chain mortising machine or vertical spindle moulding machine operating on wood or cork : b) “Circular saw” means a circular saw working in a bench (including a rack bench), but does not include a pendulum or similar saw which is moved towards the wood for the purpose of cutting operations : c) “band saw” means a band saw, the cutting portion of which runs in a vertical direction but does not include a log saw or band re-sawing machine; and d) “Planning machine” means a machine for overhand planning or for thicknessing or for both operations. 2. Stopping and starting device. – An efficient stopping and starting device shall be provided on every woodworking machine. The control of this device shall be in such a position as to be readily and conveniently operated by the person in charge of the machine. For every electrical motor driven woodworking machine, “on and off” position in respect of every switch shall be marked prominently. The starting switches and devices shall be so guarded as to prevent accidental and inadvertent starting of the machine. 3. Space around machine. - The space surrounding every woodworking machine in motion shall be kept free from obstruction. There should be ample space around each machines to enable the operator to handle pieces of timber without interfering with other machines. Sufficient room for stacking of material and passages for movement of persons to be adequate. Accumulation of scrap and shavings should be avoided to eliminate fire hazard. Finished and un-finished timber should be piled safely and neatly and attention to good house keeping should be given. 4. Floors. – The floor surrounding every woodworking machine shall be maintained in good and level condition and shall not be allowed to become slippery and as far as practicable shall be kept free from chips or other loose materials. 5. Lighting. – The machine should be located in relation to natural and artificial lighting so that the point of operation is adequately illuminated. Reflected glare and shadows shall be avoided. 6. Earth Connection. – The metal frame work of all machines having electric motors attached to them shall be effectively electrically grounded which shall be maintained in good condition. 7. Working surfaces. – The working surfaces of all machines shall be of a height which would contribute a minimum of fatigue for the operator and shall provide for easiness of operation. If necessary, a substantial platform securely fastened to the floor and of compensating height be provided, if the operator is of less than average stature and the working table can not be lowered to adjust. The height of auxiliary tables and supports should also be the same height as of the machine as far as practicable. Recommended average height from working floor to working surfaces are 36”for hand feed circular saws, 32” for power feed circular saws, 42” 47 for band saws, and 36” for shaper sand jointers. The working surface shall be kept entirely free from chips, scraps and wastes. 8. Exhaust system. – Local exhaust system shall be provided for removal of saw dust and chips at the source. 9. Stacking and Storing of Materials. – Finished, semi-finished, un-finished materials in a wood-working factory shall be neatly arranged and safely stacked providing enough space for free movement of men and materials.

Previous and next

All provisions of Tripura Factories Rules, 2007

Questions people ask

Is rule 9 of Tripura Factories Rules, 2007 still in force?

No repeal of Tripura Factories Rules, 2007 is recorded.