LawGrids logoLAWGRIDS.ORG

Rule 50, Central Motor Vehicle Rules, 1989.: Form and manner of display of registration marks on the motor vehicles

Central Motor Vehicle Rules, 1989. - Rule 50

Text of rule 50

Form and manner of display of registration marks on the motor vehicles

79[50. Form and manner of display of registration marks on the motor vehicles.—79 80[(1) On or after commencement of this rule, the registration mark referred to in sub-section (6) of section 41 shall be displayed both at the front and at the rear of all motor vehicles clearly and legibly in the form of security license plate of the following specifications, namely:— 79 Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993). 80 Sub-R. (1) substituted by G.S.R. 221(E), dated 28-3-2001 as amended by S.O. 938(E), dated 24-9-2001, S.O. 499(E), dated 9-5-2002 and S.O. 59(E), dated 21-1-2003 (w.e.f. 1-1-2004). (i) the plate shall be a solid unit made of 1.0 mm aluminium conforming to DIN 1745/DIN 1783 or ISO 7591. Border edges and corners of the plate shall be rounded to avoid injuries to the extent of approx. 10 mm and the plates must have an embossed border. The plate shall be suitable for hot stamping and reflective sheet has to be guaranteed for imperishable nature for minimum five years. The fast colouring of legend and border to be done by hot stamping; (ii) the plate should bear the letters "IND" in blue colour on the extreme left centre of the plate. The letter should be one-fourth of the size of letters mentioned in rule 51 and should be buried into the foil or applied by hot stamping and should be integral part of the plate; (iii) each plate shall be protected against counterfeiting by applying chromium-based hologram, applied by hot stamping. Stickers and adhesive labels are not permitted. The plate shall bear a permanent consecutive identification number of minimum seven digits, to be laser branded into the reflective sheeting and hot stamping film shall bear a verification inscription; (iv) apart from the registration marks on the front and rear, the third registration mark in the form of self-destructive type, chromium based hologram sticker shall be affixed on the left-hand top side of the windshield of the vehicle. The registration details such as registration number, registering authority, etc., shall be printed on the sticker. The third registration mark shall be issued by the registering authorities/approved dealers of the license plates manufacturer alongwith the regular registration marks, and thereafter if such sticker is destroyed it shall be issued by the license plate manufacturer or his dealer; 39 (v) the plate shall be fastened with non-removable/non-reusable snap lock fitting system on rear of the vehicle at the premises of the registering authority; The license plates with all the above specifications and the specified registrations for a vehicle shall be issued by the registering authority or approved the license plates manufacturers or their dealers. The Central Road Research Institute, New Delhi or any of the agency authorized by the Central Government shall approve the license plates manufacturers to the above specification; (vi) the size of the plate for different categories of vehicles shall be as follows:— For two and three-wheelers 200 x 100 mm For Light Motor Vehicles/Passenger cars 340x200mm/500x 120 mm For medium commercial vehicles, heavy 340 x200 mm: commercial vehicles and Trailer/combination Provided that this sub-rule shall apply to already registered vehicles two years from the date of commencement:] 81[Provided further that the size of the registration plates for agricultural tractors shall be as follows:— Front - - 285x45 mm Rear - 200x100 mm]: 82[Provided also that the size of registration plate for power tiller shall be 285x45 mm and shall be exhibited at the front. Further, in case of trailer coupled to power tiller, the size of registration plate shall be 200x100 mm and shall be exhibited on its rear:] 83[Provided also that in case of a motor cycle, the size of 285x45 mm for front registration plate shall also be permitted.] (2) In the case of motor cycles the registration mark in the front shall be displayed parallel to the handle bar or on any part of the vehicle including mudguard facing the front instead of, on a plate in line with the axis of the vehicle:] Provided that— (a) the registration mark exhibited at the rear of a transport vehicle shall be affixed to the vehicle on the right hand side at a distance not exceeding one metre from the ground as may be reasonably possible having regard to the type of the body of the vehicle; (b) the registration mark shall also be painted on the right and left side on the body of the vehicle in the case of a transport vehicle; (c) the registration mark shall also be painted and exhibited on the partition provided between the driver and the passengers, facing the passengers' seats or, where there is 81 Inserted by G.S.R. 720(E),dated 10-9-2003 (w.e.f. 10-10-2003). 82 Third proviso inserted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2006). 83 Fourth proviso inserted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005). 40 no such partition, on the front interior of the vehicle near the roof to the left side of the driver's seat facing the passengers' seats in the case of a stage carriage or a contract carriage and in the case of a motor cab or a taxi cab it shall be sufficient if the registration mark is painted on the dash-board; 84[(d) the letters of the registration mark shall be in English and the figures shall be in Arabic numerals and shall be shown:— (A) in the case of transport vehicles in black colour on yellow background; and (B) in other cases, in black colour on white background, the registration mark on the trailer shall be exhibited on the left hand side in black colour on yellow background. In addition, the registration mark on the drawing vehicle shall be exhibited on the trailer also and this shall be done on the right hand side at the rear of the trailer or the last trailer as the case may be, in black colour on retro-reflective type yellow background: Provided that where provisions of this clause have not been complied with in respect of motor vehicle, on or before the commencement of the Central Motor Vehicles (8th Amendment) Rules, 2001, then the provisions shall be complied with,— (i) in respect of transport vehicle, on or before 1st February, 2002; and (ii) in other cases, on or before 1st July, 2002.] 85[(3) The registration mark shall be exhibited in two lines, the State code and registering authority code forming the first line and the rest forming the second line, one below the other: Provided that the registration mark in the front may be exhibited in one line: Provided further that in models of vehicles having no sufficient provision at the rear to exhibit the registration mark in two lines, it shall be sufficient if in such vehicles registration mark is exhibited hi a single line: Provided further that registration mark on a light motor vehicle may be in the centre with illumination. (4) Every motor vehicle, except motor cab and motor car, manufactured on and from the date of commencement of the Central Motor Vehicles (Amendment) Rules, 1993, shall be provided with sufficient space in the rear for display of registration mark in two lines. (5) In case of agricultural tractors, the registration mark need not be inclined to the 86[vertical plane by more than 45 degrees]. 84 CI. (d) substituted by G.S.R. 901(E), dated 13-12-2001 (w.e.f. 13-12-2001). Earlier CI. (d) was substituted by G.S.R. 221(E), dated 28-3-2001 (w.e.f. 28-3-2001). 85 Added by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993). 41 (6) The registration mark of the drawing agricultural tractor may not be exhibited on the agricultural trailer or trailers.]

Previous and next

All provisions of Central Motor Vehicle Rules, 1989.

Questions people ask

Is rule 50 of Central Motor Vehicle Rules, 1989. still in force?

No repeal of Central Motor Vehicle Rules, 1989. is recorded.