LawGrids logoLAWGRIDS.ORG

Rule 57, The Maharashtra Factories Rules, 1963: Further safety precautions

The Maharashtra Factories Rules, 1963 - Rule 57

Text of rule 57

Further safety precautions

1[57. Further safety precautions.-Without prejudice to the provisions of sub- section (1) of section 21 in regard to the fencing of machines, the further precautions specified in the schedules annexed hereto, shall apply to the machines noted in each schedule. SCHEDULE 1 Textile including Cotton, Silk, Asbestos, Staple Fibre or any Artificial Fibre and Jute 1. All openers, scutchers, combined openers and scutchers, lap machines, hard waste breakers, cleaners, blenders, hopper feeders and similar machines.-(a) All Openers, Scutchers, Combined Openers and Scutchers, Scutcher Lap Machines, Hard Waste Breakers, Cleaners, Blenders, Hopper Feeders and similiar machines shall be driven by separate motors or from separate counter shafts provided with the fast and loose pulleys and efficient belt shifting devices. (b) In all openers, scutchers, combined openers and scutchers, scutcher lap machines, Hard Waste Breakers, Cleaners, Blenders, Hopper Feeders and similar Machines, the beater covers and doors which give access to any dangerous part of the machine shall be fitted with effective interlocking arrangements, which shall prevent the covers and doors being opened till the dangerous parts of the machine come to rest and also prevent the machine being restarted till the covers and doors are closed. (c) In all openers, scutchers, combined openers and scutchers, scutcher lap machines, Hard waste breakers, cleaners, blenders, hoppers, feeders and similar machines, the opening giving access to the dust chamber shall be provided with permanently fixed fencing, which shall, while admitting light, yet prevent contact between any part of a person's body and the beater grid bars. (d) In all openers, scutchers, combined openers and scutchers, scutcher and lap machines, silver lap machines, derby doublers, ribbon lap and similar machines, the lap forming rollers shall be fitted with a guard or cover which shall prevent access to the intake of the lap roller and fluted roller as long as the weighted rock is down or the guard or cover shall be so interlocked that it cannot be raised until the machine is stopped and the machine cannot be restarted until the guard or cover is closed: Provided that in case of similar machines run at higher speed and provided with an automatic lap starter mechanism, the machines shall be immediately put out of use, no sooner this mechanism goes out of order for any reason and the same shall not be recommissioned till the automatic mechanism is repaired and placed back in efficient working order. 2. Carding Machines.- All cylinder doors shall be secured by an automatic locking device which shall prevent the door being opened until the cylinder/cylinders ceased to revolve and shall render it impossible to restart the machine, until the door is closed. 2[Provided that the latter requirement in respect of the automatic locking device shall not apply while stripping or grinding operations are carried out; Provided further that stripping or grinding operations shall be carried out only by specially trained adult workers wearing tight fitting clothing whose names have been re- corded in the register prescribed in this behalf as required in sub-section (1) of Section 22.] (b) Access to the licker-in cylinder from the back and the sides shall be positively prevented so long as the licker-in cylinder is rotating, by suitably designed and placed guards. 1 Rule 57 and the Schedules I to IX subs. by G.N. dt. 28th September, 1976 2 Ins. by G.N. dt. 20.7.1981 112 The Maharashtra Factories Rules, 1963 3. Drawing Frame.-The gearing for driving the draft rollers on drawing frames shall be effectively guarded by a cover which shall be so interlocked that it cannot be raised until the machine is stopped and the machine cannot be restarted until the cover is closed. 4. Speed Frames.-Headstocks shall be fitted with automatic locking arrangements which shall prevent the doors giving access to the jack box wheels being opened while the machinery is in motion and shall render it impossible to restart the machine until the doors are closed. 5. Combers and similar machines.-(a) The gearing shall be effectively guarded by a cover which shall be so interlocked that it cannot be raised until the machine is stopped and the machine cannot be restarted until the cover is closed. (b) A fixed guard of a suitable design shall be provided which would prevent access to the draw box rollers in motion. 6. Self-acting Mules.- The drive shall be from countershaft which shall be provided with fast and loose pulleys and efficient belt shifting devices. 7. Process House Machinery etc.- (a) In respect of calendering mangles Roller Printing Machine merciring, soaping, stentering, singeing, shrinking, washing and similar machines, all such machines shall be provided with an efficient nip guard along the whole length on the intake side of each pair of bowls and similar parts, as would prevent access to the point of contact of the rollers or bowls: Provided that, in the case of those machines in respect of which it is not possible to provide efficient "nip" guards on account of the corrosive action of chemical used in the process or on account of the size of the material passing through the bowls, efficient fixed guards shall be provided on either side of the machines as would positively prevent any access to the point of contact of the rollers or bowls: Provided further that in respect of rollers or bowls of such machines with ends of lesser diameter, the "nip" guards shall have flattened ends on either side to prevent access between the guard and the roller or bowl ends moving in. (b) In respect of felt calendering machines or any type, dangerous intake points between moving felt or belt and the central or other guide drums shall be securely fenced from the front and also from the sides, of such intake points as are accessible from working floors or platforms. 8. Shearing and Cropping Machines.-The dangerous moving outer blades shall be provided with an efficient interlock arrangement as would prevent the complete cover or guard to be opened until the cutter blade has come to rest and would also make it impossible to restart the machine until the cover or guard is closed. 9. Singeing Machines.- Effective arrangement such as solenoid valve or other effective device shall be provided to cut off instantaneously supply of any type of gas or of electricity to the machine, in case of failure of power to the machine. SCHEDULE II Cotton Ginning Machinery 1. Line Shaft.- The line shaft or second motion in cotton ginning factories when below floor level, shall be completely enclosed by a continuous wall or unclimbable fencing with only so many openings as are necessary for access to the shaft for removing cotton seed, cleaning and oiling, and such openings shall be provided with gates or doors, which shall be kept closed and locked. 2. The bare portions of the line shaft between the bearings and also of the projection at the ends of the line shaft shall be provided with adequate inverted "U" or sleeve type of guards of substantial construction. SCHEDULE III Wood Working Machinery 1. Definitions.- For the purposes of this Schedule- The Maharashtra Factories Rules, 1963 113 (a) "Wood working machine" means a circular saw, band saw, planning machine, chair mortising machine or vertical spindle moulding machine operating on wood or cork. (b) "Circular saw" means a circular saw working in a bench (including a rack bench) but does not include a pendulum or similar saw which is moved towards the wood for the purpose of cutting operations. (c) "Band saw" means a band saw, the cutting portion of which runs in vertical direction but does not include a log saw or band re-sawing machine; (d) "Planning machine" means a machine for overhead planning or for thickening or for both operations. 2. Stopping and starting device.- An efficient stopping and starting device shall be provided on every wood-working machine. The control of this device shall be in such a position as to be readily and conveniently operated by the person in charge of the machine. 3. Space around machine.-The space surrounding every wood-working machine in motion shall be kept free from obstruction. 4. Floor.-The floor surrounding every wood-working machine shall be maintained in good and level condition and shall not be allowed to become slippery and as far as practicable shall be kept free from chips or other loose material. 5. Training and supervision.- (1) No person shall be employed at a wood-working machine unless he has been sufficiently trained to work that class of machine or unless he works under the adequate supervision of a person who has a thorough knowledge of the working of the machine. (2) A person who is being trained to work a wood-working machine shall be fully and carefully instructed to the danger of the machine and the precautions to be observed to secure safe working of the machine. 6. Circular saw.- Every circular saw shall be fenced as follows:- (a) Behind and in direct line with the saw there shall be an arriving knife, which shall have a smooth surface, shall be strong, rigid and easily adjustable, and shall also conform in the following conditions:- (i) The edge of the knife nearer the saw shall form an area of a circle having a radius not exceeding the radius of the largest saw used on the bench. (ii) The knife shall be maintained as close as practicable to the saw having regard to the nature of the work being done at the time, and at the level of the bench table. The distance between the front edge of the knife and the teeth of the saw shall not exceed 10 mms. (iii) For a saw having diameter of less than 60 cms., the knife shall extend upwards from the bench table to within 25 mms. of the ton of the saw, and for a saw having a diameter of 60 cms. or over shall extend upwards from the bench table to a height of atleast 22.5 cms. (b) The top of the saw shall be covered by a strong and easily adjustable guard, with a flange at the side of the saw farthest from the fence. The guard shall be kept so adjusted that the said flange shall extend below the roots of the teeth of the saw. The guard shall extend from the top of the arriving knife to a point as low as practicable at the cutting edge of the saw. (c) The part of the saw below the bench table shall be protected by two plates of metal or other suitable materials one on each side of the saw. Such plate shall not be more than fifteen centimeters apart and shall extend from the axis of the saw outwards to a distance of not less than five cms. beyond the teeth of the saw. Metal plates, if not beaded, shall be of a thickness of at least 2.5 mms. or if beaded be of a thickness of at least 1.25 mms. 7. Push Sticks.- A push stick or other suitable appliance shall be provided for use at every circular saw and at every vertical spindle moulding machine to enable the work to be done without unnecessary risk. 114 The Maharashtra Factories Rules, 1963 8. Band saws.- Every band saw shall be guarded as follows:- (a) Both sides of the bottom pulley shall be completely encased by sheet or expanded metal or other suitable material. (b) The front of the top pulley shall be covered with sheet or expanded metal or other suitable material. (c) All portions of the blade shall be enclosed or otherwise securely guarded except the portion of the blades between the bench table and the top guide. 9. Planing machines.-(1) A Planing machine (other than planing machine which is mechanically fed) shall not be used for overhead planing unless it is fitted with a cylindrical cutter block. (2) Every planing machine used for overhead planing shall be provided with a "bridge" guard capable of covering the full length and breadth of the cutting slot in the bench and so constructed as to be easily adjusted both in a vertical and horizontal direction. (3) The feed roller of every planing machine used for thickening except the combined machine for overhead planing and thickening shall be provided with efficient guard. 10. Vertical Spindle Moulding Machine.- (1) The cutter of every vertical spindle moulding machine shall be guarded by the most efficient guard having regard to the nature of the work being performed. (2) The wood being moulded, at a vertical spindle moulding machine shall if practicable be held in a jig or holder of such construction as to reduce as far as possible the risk of accident to the workers. 11. Chain Mortising Machine.- The chain of every chain mortising machine shall be provided with a guard which shall enclose the cutter as far as practicable. 12. Adjustment and maintenance of guards.- The guards and other appliances required under this Schedule shall be- (a) maintained in an efficient state, (b) constantly kept in position while the machinery is in motion, and (c) so adjusted as to enable the work to be done without risk. SCHEDULE IV Rubber and Plastic Mills 1. Definition.-(i) A "Rubber and Plastic Mills" shall mean machine with rollers used in breaking down, cracking, washing, grating, mixing, refining and warming of rubber or rubber goods and plastic or plastic goods. (ii) A "Calender" shall mean machine with rolls used for frictioning, sheeting, coating and spreading of rubber compounds and plastic or plastic compounds. Installation of machines.- Rubber and plastic mills shall be so installed that top of the front roll is not less than one metre above the floor or working level provided that in existing installations where the top of the front roll is below this height a strong rigid distance bar guard shall be fitted across the front of the machine in such position that the operator cannot reach the nip of the roller from the normal working position of the operator. 2. Safety Devices.- (i) Rubber and Plastic Mills shall be equipped with- (a) Hoppers so constructed or guarded that it is impossible for the operators to come into contact in any manner with the nip of the rolls, or Horizontal Safety.- Trip rods or tight wire cable across both front and rear, which will when pushed or pulled operate instantly to disconnect the power and apply the brakes or to reverse the rolls. Safety-trip rods or tight wire cable on rubber mills shall extend across the entire length of the face of the rolls and shall be located not more than 170 centimeters above the floor or working level. (ii) Calender machines shall be equipped with- The Maharashtra Factories Rules, 1963 115 (a) Horizontal safety-trip rods or tight wire across both front and rear, which will when pushed or pulled operate instantly, to disconnect the power and apply the brakes or to reverse the roll; (b) Safety-trip rods or tight wire cables on calender machines shall extend across the entire length of the face of the roll and shall be located not more than 170 centimetres above the floor or working level; (c) on each side of all calenders and near both ends of the face of the rolls there shall be a vertical tight wire cable connecting with the bar tripping mechanism at the top and fastened to the frame within 30 centimetres of the floor. These cables should be positioned at a distance of not more than 30 centimetres from the face of the roll and a distance of not less than 25 millimetres from the calender frame. 3. Maintenance and safety devices.- Safety trip rods and tight wire cables on all rubber mills and calenders shall be examined and tested daily in the presence of the Manager or other responsible person and if any defect is disclosed by such examination and test the mill shall not be used until such defect has been remedied. 4. Injunction Moulding Machine.-(a) An electrical interlock arrangement shall be provided so that the moulds cannot be closed unless the front safety gate is fully closed and on opening the front safety gate, the moulds will stop automatically. (b) In addition to the above arrangement an hydraulic safety shall also be incorporated with the front safety gate. This shall prevent the tail stock mould plate from moving forward on opening of the front safety gate. (c) At the rear of the machine, there shall be provided either an efficient fixed guard or a sliding gate which shall be electrically inter-locked with the movement of the mould plates in the manner of the front safety gate as required under (a) above so as to prevent access to the danger zone of the moulds in motion from the rear. SCHEDULE V Centrifugal Machines 1. Definition.-"Centrifugal Machine" includes centrifugal extractors, or droextractors, separators and driers. 2. Centrifugal machines shall be provided with efficient inter locking devices that will physically prevent the lids from being opened whilst the rotating drums or brackets are in motion under power or due to power derived earlier and by then switched off and would also prevent the starting of the drums or baskets under power while the lids are open. 3. Centrifugal machines shall not be operated at a speed in excess of the manufacturer's rating which shall be legibly stamped by the manufacturer both on the inside of the bracket and on the outside of the machine casing at easily-visible places. 4. All centrifugal machines shall be provided with effective braking arrangements, to bring cage, drum or basket to rest within a reasonable short period of time, after the power to drive the motor is cut off. 5. The cages, drums or baskets shall be thoroughly examined by a competent person regularly to check their balance and effective steps shall be taken in case unbalance at high speed is observed to restore their balance before re-commissioning the machines: Provided that clauses 2, 3 and 4 shall not apply in case of top lung similar machines used in the sugar manufacturing industry. SCHEDULE VI 1[Shears, Slitters and Guillotine Machines] 1. Definition.- The term "shears, slitters and guillotine" means a machine, whether driven by power or otherwise, equipped with a straight beveledged blade operating vertically against a resisting edge and used for shearing metals or non-metallic substances. 1 Subs. by MGG Pt.I-L Ext. dt. 10.8.1989 p. 302 116 The Maharashtra Factories Rules, 1963 2. A barrier metal guard of adequate strength shall be provided at the front of the knife, fastened to the machine frame and shall be so fixed as would prevent any part of the operator's body to reach the descending blade from above, below or through the barrier guard or from the sides: Provided that in case of machines used in the paper printing and allied industries, where a fixed barrier metal guard is not suitable on account of the height and volume of the material being fed, there shall be provided suitable starting devices which require simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade. 3. At the back end of such machines, an inclined guard shall be provided over which the slit pieces would slide and be collected at a safe distance in a manner as would prevent a person at the back from reaching the descending blade. 1[4. Slitting Machines:-`Slitter' or `Slitting Machine' means a machine ordinarily equipped with circular disc-type knives, and used for trimming or cutting into metal or non- metallic substances or for slitting them into narrow strips; for the purpose of this Schedule, this term includes bread or other food slicers equipped with rotary knives or cutting discs. 1. Slitting Machines:- Circular disc-type knives on machines for cutting metal, leather, paper, rubber, textiles or other non-metallic substances shall, if within reach of operators standing on the floor or working level, be provided with guards enclosing the knife edges at all times as near as practicable to the surface of the material and which may either- (a) automatically adjust the

Previous and next

All provisions of The Maharashtra Factories Rules, 1963

Questions people ask

Is rule 57 of the Maharashtra Factories Rules, 1963 still in force?

No repeal of the Maharashtra Factories Rules, 1963 is recorded.