LawGrids logoLAWGRIDS.ORG

Rule 124B, The Factory rules 1962: Surveillance of the work environment

The Factory rules 1962 - Rule 124B

Text of rule 124B

Surveillance of the work environment

124B. Surveillance of the work environment. - (1) In addition to generality of the provisions of Sections 7-A and 7-B, the occupier of the factory involved in hazardous process, shall make necessary arrangements for monitoring of level of exposure of chemical and toxic substances (whether hazardous or otherwise) in the work environment of the factory, as may be further instructed by the Chief Inspector. (2) Without prejudice to the requirements in any other provisions in the Act or the rules, the requirement specified in the following schedule for permissible levels or certain chemical substance in work-environment shall apply to all factories.] Schedule 1. Definitions. - For the purpose of this schedule- (a) "mg/m3" means milligrams of a substance per cubic meter of air; (b) "ppem" means million particles of a substance per cubic meter of air; (c) "ppm" means parts of vapour or gas per million parts of air by volume at 25°C and 760 mm of mercury pressure; (d) "Times weighted average concentration" means the average concentration of a substance in the air at any work location in a factory computed from evaluation of adequate number of air samples taken at the location, spread over the entire shift on any day, after giving weightage to the duration for which each such sample is collected and the concentration prevailing at the time of taking the sample. Time weighted average concentration. C1T1 + C2T2 .... CnTn T1 T2 ..... Tn Where C1 represents the concentration of the substance for duration T1 (in hours); C2 represents the concentration of the substance for duration T2 (in hours); and Cn represents the concentration of the substance for duration Tn (in hours). (e) "work location" means a location in a factory at which a worker works or may be required to work at any time during any shift on any day. 2. Limits of concentrations of substances at work locations. - (1) The time weighted average concentration of any substance listed in Table 1 or 2 of the schedule, at any work location in a factory during any shift on any day shall not exceed the limit of the permissible time weighted average concentration specified in respect of that substance : Provided that in the case of a substance mentioned in Table 1 in respect of which a limit in terms, of short term maximum concentration is indicated, the concentration of such a substance may exceed the permissible limit of the time weighted average concentration for the substance for short periods not exceeding 15 minutes at a time, subject to the condition that- (a) such periods during which the concentration exceeds the prescribed time weighted average concentration are restricted to not more than 4 per shift; (b) the time interval between any two such periods of higher exposure shall not be less than 60 minutes; (c) at no time the concentration of the substance in the air shall exceed the limit of short term maximum concentration. (2) In the case of any substance given in Table 3, the concentration or the substance at any work location in a factory at any time during any day shall not exceed the limit of exposure for that substance specified in the table. (3) In the cases where the word "skin" has been indicated against certain substance mentioned in Tables 1 and 3, appropriate measures shall be taken to prevent absorption through cutaneous routes particularly skin, mucous membrances, and eyes as the limits specified in these Tables are for conditions where the exposure is only through respiratory tract. (4) (a) In case, the air at any work location contains a mixture of such substances mentioned in Table 1, 2 or 3, which have similar toxic properties, the time weighted concentration of each of these substances during the shift should be such, that when these time weighted concentration divided by the respective permissible time weighted average concentration specified in the above mentioned tables, and the fractions obtained are added together, the total shall not exceed unity; i.e. C 1 L 1 + C 2 L 2 + ........... C n L n should not exceed unity when C1, C2........ Cn are the time weighted concentration of toxic substances 1, 2,......... and n respectively, determined after measurement at work location; and L1, L2...........Ln are the permissible time weighted average concentration of the toxic substances 1, 2 ........ and n respectively. (b) In case the air at any work location contain a mixture of substances, mentioned in Table 1, 2 or 3, and these do not have similar toxic properties, then the time weighted concentration of each of these substances shall not exceed the permissible time weighted average concentration specified in the above mentioned tables, for that particular substances. (c) The requirement in clauses (a) and (b) shall be in addition to the requirements in paragraphs (1) and 2 (2). 3. Sampling and evaluation 4 procedures. - (1) Notwithstanding provisions in any other paragraphs, the sampling and evaluation procedures to be adopted for checking compliance with the provisions in the schedule shall be as per standard procedures in vogue from time to time. (2) Notwithstanding the provisions in paragraph 5, the following conditions regarding the sampling and evaluation procedures relevant to checking compliance with the provisions in this schedule are specified :- (a) For determination of the number of particles per cubic meter in item 1 (a)(i)(l) in Table 2, samples are to be collected by standard or midget impinger and the count made by lightfield technique; (b) The percentage of quartz in the 3 formula given in item 1 (a)(i) of Table 2 is to be determined from air borne samples; (c) For determination of number of fibres as specified in item 2 (a) of Table 2, the memberance filter method at 400-450 X magnification (4 mm objective) with phase contrast illumination should be used; (d) Both for determination of concentration and percentage of quartz for use of the formula given in item 1 (a)(i)(2) of Table 2, the fraction passing through a size-selector with the following characteristics should not be considered. Aerodynamic diameter (unit density sphere) Percentage allowed by size-selector 2.0 90 2.5 75 3.5 50 5.0 25 10.0 0 4. Power to require assessment of concentration of substances. - (1) An Inspector may, by an order in writing, direct the occupier or manager of a factory to get the assessment of the time weighted average concentration at any work location of any of the substances mentioned in Table 1, 2 or 3 carried out, by the Government's Industrial Hygiene Laboratory. The services of the laboratory may be requisitioned by the occupier or manager of the factory, with their consent and after payment of fees of laboratory services the rates as may be specified by order by the State Government from time to time. (2) The results of such assessment as well as the method followed for air sampling and analysis for such assessment furnished by the laboratory shall be sent to the Inspector within 3 days from the date of completion of such assessment by the occupier or manager and also a record of the same kept readily available for inspection by an Inspector. 5. Exemption. - If in respect of any factory or a part of a factory, the Chief Inspector is satisfied that, by virtue of the pattern of working time of the workers at different work locations or on account of other circumstances, no worker is exposed in the air at the work locations, to a substance or substances specified in Table 1, 2 or 3 to such an extent as is likely to be injurious to his health. He (the Chief Inspector) may by an order in writing exempt the factory or a part of the factory from the requirements in paragraph 2, subject to such conditions if any, as he may specify therein. 6. Change of permissible limit. - The permissible limits listed in following Tables (1), (2) and (3) of this Schedule and the permissible limits as specified in the Second Schedule of the Factories Act, 1948 are the same. Hence at any change in the limits specified in the second schedule of the Act, those substituted limits shall be applicable under this Schedule as if the same have been incorporated in its tables. Permissible Levels of Certain Chemical Substances in Work Environment S. Substance Permissible limits of exposure No. Time weighted average concentration. (TWA) (8 hrs.) Short-term exposure limits (STEL) (15 min)* ppm mg/mp3** ppm mg/mp3** 1 2 3 4 5 1. Acetaldehyde 100 180 150 270 2. Acetic Acid 10 25 15 37 3. Acetone 750 1780 1000 2375 4. Acrolein 0.1 0.25 0.3 0.8 5. Acrylonitric skin (S.C.) 2 4.5 - - 6. Aldrin-Skin - 0.25 - - 7. Allyl chloride 1 3 2 6 8. Ammonia 25 18 35 27 9. Anilink Skin 2 10 - - 10. Anilidine (Opisomers Skin) 0.1 0.5 - - 11. Arsenic & soluble Compounds (as As) - 0.2 - - 12. Benzene (S.C.) 10 30 - - 13. Beryllium & compounds (as Be) (S.C.) - 0.002 - - 14. Borom trifluroide-C 1 3 - - 15. Bromine 0.1 0.7 0.3 2 16. Butane 800 1900 - - 17. 2 Butanone (Mothylethy Ketone MEK) 200 590 300 885 18. n-Butyle acetate 150 710 200 950 19. N-Butyl alcohol Skin-C 50 150 - - 20. Sec/tert. Butyl acetate 200 950 - - 21. Butyl merceptan 0.5 1.5 - - 22. Cadmium dust and salts (as CD) - 0.05 - - 23. Calcium Oxide - 2 - - 24. Carbaryl (Sevin) - 5 - - 25. Carbofuran (Furadan) - 0.1 - - 26. Carbon disulphide-Skin 10 30 - - 27. Carbon monoxide 50 55 400 440 28. Carbon tetrachloride -Skin (S.C.) 4 30 - - 29. Chlordane (Skin) - 0.5 - 2 30. Chlorobenzene (Monochloro-bezene) 75 350 - - 31. Chloroform (S.C.) 10 50 - - 32. Chlorine 1 3 3 9 33. bis-Chloromethyl ether 0.001 0.005 - - 34. Chromic acid and chromites (as Cr.) - 0.05 - - 35. Chromous Salts (as Cr) - 0.05 - - 36. Copper Fume - 0.2 - - 37. Cotton dust, raw - 0.2+ - - 38. Cresol, all isomers (Skin) 5 22 - - 39. Cyanides (as Ch)-(Skin) - 5 - - 40. Cyanogen 10 20 - - 41. DDT (Dichloridiphenyl - 1 - - trichloroethane) 42. Demeton skin 0.01 0.1 - - 43. Diazinon-skin - 0.1 - - 44. Dibutyle Phthalate - 5 - - 45. Dichlorves (DD VP)-skin 0.1 1 - - 46. Dield-rin-skin - 0.25 - - 47. Dinitre benzene (all isomers-skin) 0.15 1 - - 48. Dinitootoluene-skin - 1.5 - - 49. Diphenyl (Biphenyl) 0.2 1.5 - - 50. Endosulfan (Thiodan(-Skin - 0.1 - - 51. Endrin-skin - 0.1 - - 52. Ethyl acetate 400 1400 - - 53. Ethyl amine 10 18 - - 54. Ethyl alcohol 1000 1900 - - 55. Fluorides (as F) - 2.5 - - 56. Flourine 1 2 2 4 57. Formaldehyde (S.C.) 1.0 1.5 2 3 58. Formic acid 5 9 - - 59. Gasoline 300 900 500 1500 60. Hydrogen Skin (S.C.) 0.1 0.1 - - 61. Hydrogen cyanide-C 5 7 - - 62. Hydrogen cyanide-skin-C 10 10 - - 63. Hydrogen fluoride (as F)-C 3 2.5 - - 64. Hydrogen peroxide 1 1.5 - - 65. Hydrogen sulphide 10 14 15 21 66. Iodine-C 0.1 1 - - 67. Iron oxide from (FEg Os as Fe) - 5 - - 68. Isommyl acetate 100 525 - - 69. Isobutyl alcohol 50 150 - - 70. Isoamyl alcohol 100 360 125 450 71. Lead, inorg, fumes and dust (as Pb) - 0.15 - - 72. Lindane-skin - 0.5 - - 73. Malathoion-skin - 10 - - 74. Manganese (as Mn) dust and xompounds-C - 5 - - 75. Manganese fume (as Mn) - 1 - - 76. Mercury (as Hg)-Skin- (i) Alkyl compounds - 0.01 - 0.03 (ii) All forms except alkyl vapour - 0.05 - - 77. Mercury (as Hg) Aryl and inorganic compounds - 0.1 - - 78. Methyl alcohol (methenol) skin 200 260 250 310 79. Methyl collosove-skin (2-methoxy ethanol)-Skin 5 16 - - 80. Methyl isobutyl Ketone 50 205 75 300 81. Methyl isoyanate-Skin 0.02 0.05 - - 82. Napthalene - - - - 83. Nickel corbony (as Nil) 10 50 15 75 84. Nitric acid 2 5 4 10 85. Nitric Oxide 25 30 - - 86. Nitrobenzine-skin 1 5 - - 87. Nitrogen dioxide 3 6 5 10 88. Oil mist-mineral - 5 - 10 89. Ozone 0.1 0.2 0.3 0.6 90. Parathion-skin - 0.1 - - 91. Phenol-skin 5 19 - - 92. Phroate (Thimet)-skin - 0.05 - 0.2 93. Phosgene (Carbonyl chloride) 0.1 0.4 - - 94. Phosphine 0.3 0.4 1 1 95. Phosphoric acid - 1 - - 96. Phosphorus (Yellow) - 0.1 - - 97. Phosphorus pentachloride 0.1 1 - - 98. Phosphorus trichloride 0.2 1.5 0.5 3 99. Picric acid-skin - 0.1 - 0.3 100 . Peyridine 5 15 - - 101 . Sila-ne (Sillicon tetrahydrine) 5 7 - - 102 . Sodium-hydroxide-C - 2 - - 103 . Styrene, monomer (pheny-othylene) 10 215 100 425 104 . Sulphur dioxide 2 5 5 10 105 . Sulpur hexafluoride 1000 6000 - - 106 . Sulfuric acid - 1 - - 107 . Tetraethyl lead (as Pb)-Skin - 0.1 - - 108 . Toluene (toluo) 100 375 150 560 109 . O-Toludine-Skin (S.C.) 2 9 - - 110 . Tributyl phosphate 0.2 2.5 - - 111 . Trichloroethylene 50 270 200 1080 112 . Uranium, natural (as U) - 0.2 - 0.6 113 . Vinyl chloride (H.C.) 5 10 - - 114 . Welding Funes - 5 - - 115 . Xylene (o-m-pisomers) skin 100 435 150 655 *Lint-free dust as measured by vertical elutriator cotton-dust sampler. Table 2 Substance Permissible time-weighted average concentration. 1. Silica- (a) Crystalline- (i) Quartz- (1) In terms of dust count 1060 % Quartz + 10 Mppcm (2) In terms of respirabl e dust 10 % respirable quartz + 2 mq/m33 (3) In terms of total dust 30 % quartz - 3 mg/m3 (ii) Cristobalite .. . Half the limits given against quartz. (iii) Tridymite .. . Half the limits given against quartz. (iv) Silica fused .. . Same limit as for quartz. (v) Tripoli .. . Same limit as in formula in item given against quartz. (b) Amorphous .. . (750 mppcm) or 10 mg/m3 Total dust. 2. Silicate having less than 1% free silca by weight- (a) Asbestos-fibres longer 5 microns- (i) Amosite .. . 0.5 fibre/cubic centimeter. (ii) Chrysolite .. . 2 fibres/cubic centimeter. (iii) Crocidolite .. . 0.2 fibre/cubic centimeter. (iv) Other form .. . 2 fibres/cubic centimeter grater than 5 m in length and less than 3 micron in breadth with length to breadth ratio equal to or grater to 3:1 (b) Mica .. . 705 mppcm or 10 mg/m3 (c) Mineral wool fibre .. . 10 mg/m3 (d) Porlite .. . 1060 mppcm. (e) Portland cement .. . 10 mg/m3 Total dust containing less than 1% quartz. (f) Soap stone .. 705 mppcm. . (g) Talc (non-abostiform) .. . 705 mppcm. (h) Talc (fibrous) .. . Same limit as for asbestos. (i) Tromolite .. . Same limit as for asbestos. 3. Coal dust- (1) For airborne dust having less than 5% silicon dioxide by weight : 2mg/m3 (2) For airborne dust having over 5% silicon dioxide quartz. Same limit as prescribed by in item (2) against quartz. (1) (2) (3) (4) (5) (6) 116 . Zinc oxide- (i) Fume - 5.0 - 10 (ii) Dust (Total dust) - 10.00 - - 117 . Zirconium compounds (as Zr) - 5 - 10 ppm : Parts of vapour or gas per million parts of contaminated air by volume as 25°C and 700 mm of Hg. mg/m3 : Miligram of substance per cubic metre of air. * : Not more than 4 times a day with at least 60 min. interval between successive exposures. ** : mg/m3 = Molecular weight 24.45 x ppm Table 3 Substance Permissible limit of exposure. PPM mg/m3 (1) (2) Acetic an-hydride 5 20 O-Dichlorobenzene 50 300 Formaldehyde 2 3 Hydrogen Chloride 5 7 Manganese and Compounds (as Mn) ... 5 Nitrogen-dioxide 5 9 Nitroglycerin-skin 02 2 Potassium hydroxide ... 2 Sodium hydroxide ... 2 2, 4, 6-Trinitrotoluent (TNT) ... 0.5

Previous and next

All provisions of The Factory rules 1962

Questions people ask

Is rule 124B of the Factory rules 1962 still in force?

No repeal of the Factory rules 1962 is recorded.