LawGrids logoLAWGRIDS.ORG

Rule 59, The Factory rules 1962: Further safety precautions

The Factory rules 1962 - Rule 59

Text of rule 59

Further safety precautions

59. Further safety precautions. - Without prejudice to the provisions of sub-section (1) of Section 21 in regard to the fencing of machines, the further precautions specified in the schedules annexed hereto shall apply to the machines noted in each schedule [and the register for adult worker employed for work on or near machinery in motion shall be in Form 34.] [Schedule I] Textile Machinery except Machinery used in Jute Mills 1. Application. - The requirements of this schedule shall apply to machinery in factories engaged in the manufacture or processing of textiles other than jute textiles. 2. Definitions. - For the purpose of this schedule- (a) "Calender" means a set of heavy rollers mounted on vertical side frames and arranged to pass doth between them. Calenders may have two to ten rollers, or bowls, some of which can be heated; (b) "Embossing calender" means a calender with two or more rolls, one of which is engraved for producing figure effects of various kinds on a fabric; (c) "Card" means a machine consisting of cylinders of various sizes and in certain cases flats covered with card clothing and set in relation to each other so that fibres in staple form may be separated into individual relationship. The speed of the cylinders and their direction of rotation varies. The finished product is delivered as a sliver. Cards of different types are : the revolving flat card, the roller and clearer card, etc.; (d) "Card clothing" means the materials with which the surfaces of the cylinder doffer, flats, etc. of a card are covered and consists of a thick foundation material made of, textile fabrics through which are pressed many fine closely paced, specially bent wires, or mounted saw-toothed wire; (e) "Comber" means a machine for combing fibres of cotton, wool, etc. The essential parts are a device for feeding forward fringe of fibres at regular intervals and arrangements of combs or pins, which, at the right time, pass through the fringe. All tangled fibres, shortfibres and nips are removed and the long fibres are laid parallel; (f) "Combing machinery" means a general classification of machinery including combers, silver lap machines, ribbon lap machines, and gill boxes, but excluding cards; (g) "Rotary staple Cutter" means a machine consisting of one or more rotary blades used for the purpose of cutting textile fibres into staple length; (h) "Garnett machine" means any of number of types of machines for opening hard twisted waste of wool, cotton, silk etc. Essentially, such machines consist of a licker-in; one or more cylinders, each having a competent worker and stipper rolls; and a fancy roll and doffer. The action of such machines is some what like that a wool card, but it is much more severer in that the various rolls are covered with garnett wire instead of card clothing; (i) "Gill box" means a machine used in the worsted system of manufacturing yarns. Its function is to arrange fibres in parallel order. Essentially, it consists of a pair of feed rolls and a series of followers where the followers move at a faster surface speed and perform a combing action; (j) "In-running rolls" means any pair of rolls or drums between which there is a "nip"; (k) "Interlocking arrangement" means a device that prevents the setting in motion of a dangerous part of a machine or the machine itself while the guard cover or door provided to safeguard against danger is open or unlocked, and which will also hold the guard, cover or door closed and locked while the machine or the dangerous part is in motion; (l) "Kier" means a large metal vat, usually a pressure type, in which fabrics may be boiled cut, bleached, etc.; (m) "Ribbon tapper" means a machine or a part of a machine used to prepare laps for feeding a cotton comb; its purpose is to provide a uniform lap in which the fibres have been straightened as much as possible; (n) "Sliver tapper" means a machine or a part of a machine in which a number of parallel card slivers are drafted slightly, laid side by side in a compact sheet, and wound into a cylindrical package; (o) "Loom" means a machine for effecting the interlocking of two series of years crossing one another at right angles. The wrap yarns are wound on a warp beam and pass through headless and reeds. The filling is shot across in a shuttle or otherwise and settle in place by reeds and slay, and the fabric is wound on a cloth beam; (p) "Starch mangle" means a mangle that is used specifically for starching cotton goods. It commonly consists of two large rolls and a shallow open vat with several immersion rolls. The vat contains the starch solution; (q) "Water mangle" means a calender having two or more rolls used for squeezing water from fabrics before drying. Water mangles also be used in other ways during the finishing of various fabrics; (r) "Mule" means a type of spinning frame having a head stock and a carriage as its two main sections. The headstock is stationary. The carriage is movable and it carries the spindles which draft and spin the roving into yarn. The carriage extends over the whole width of the machine and moves slowly toward and away from the head stock during the spinning operation; (s) "Nip" is the danger zone between two rolls or drums which by virtue of their positioning and movement create a nipping hazard; (t) "Openers and pickers" means a general classification of machinery which includes breaker pickers, intermediate pickers, finisher pickers, single process pickers, multiple process pickers, willow machines, card and picker waste cleaners, thread extractors, shredding machines, roving waste openers, shoddy pickers, bale breakers, feeders, vertical openers, lattice cleaners, horizontal cleaners, and any similar machinery equipped with either cylinders, screen section, calender section, rolls, or beaters used for the preparation of stock for further processing; (u) "Paddler" means a trough for a solution and two or more squeeze rolls between which cloth-passes after being passed through a mordant or dye bath; (v) "Plaiting machine" means a machine used to lay cloth into folds of regular length for convenience of subsequent process or use; (w) "Roller printing machine" means a machine consisting of a large control cylinder, or pressure bowl, around the lower part of the perimeter of which is placed a series of engraved colour rollers (each having a colour trough), a furnisher roller, doctor blades, etc. The machinery is used for printing fabrics; (x) "Continuous bleaching range" means a machine for bleaching of cloth in rope or open width form with the following arrangement. The cloth, after wetting-out, pass through a squeeze roll into a saturator containing a solution of caustic soda and then to an enclosed J-box. A V-shaped arrangement is attached to the front part of the J-box for uniform and rapid saturation of the cloth with steam before it is packed down in the J-box. The cloth, in a single stand rope form, passes over a guide roll down the first arm of the "V" and up to the second. Steam is injected into the "V" at the upper end of the second arm so, that the cloth is rapidly saturated with steam at this point. The J-box capacity is such that cloth will remain hot for a sufficient time to complete the scouring action. It then passes a series of washers with a squeeze roll in between. The cloth then passes through a second set of saturator, J-box and washer, where it is treated with the peroxide solution. By slight modification of the form of the unit, the same process can be applied to open width cloth; (y) "Mercerizing range" means a 3-bowl mangle, a tender frame, and a number of bowls for washing and scouring. The whole set-up is in a straight line and all parts operate continuously. The combination is used to saturate the cloth with sodium hydroxide, stretch it while saturated, and washing out of the caustic before releasing tension; (z) "Sanferizing machine" means a machine consisting of a large steam-heated cylinder, and endless, thick, woolen felt blanket which is in close contact with the cylinder for most of its perimeter, and an electrically heated shoe which presses the cloth against the blanket while the later is in a stretched condition as it curves around feed-in-roll; (aa) "Shearing machine" means a machine used for shearing cloth. Cutting action is provided by a number of steel blades spirally mounted on a roller. The roller rotates in close contact with a fixed ledger blade. There may be from one to six such rollers on a machine; (bb) "Singing machine" means a machine which comprises of a heated roller, plate, or an open gas flame. The cloth or yarn is rapidly passed over the roller or the plate or through the open gas flame to remove fuzz or hairiness by burning; (cc) "Slasher" means a machine used for applying a size mixture to warp yarns. Essentially, it consists of a stand for holding section beams, a size box, one more cylindrical dryers or an enclosed hot air dryer, and beaming and for winding the yarn on the loom beams; (dd) "Tender frame" means a machine for drying cloth under tension. It essentially consists of a pair of endless travelling chains fitted with clips of fine pins and curved tracks. The cloth is firmly held at the salvages by the two chains which diverge as they move forward so that the cloth is brought to the desired width; (ee) "Warper" means a machine for preparing and arranging the yarns intended for the warp of a fabric, specifically, a beam warper. 3. General safety requirements. - (1) Every textile machine shall be provided with individual machinical or electrical means for starting and stopping such machines. Belt shifter on machines driven by belts and shafting should be provided with a belt shifter lock or an equivalent positive locking device. (2) Stopping and starting handless or other controls shall be of such design and so positioned as to prevent the operator's hand or fingers from striking against any moving part or any other part of the machine. (3) All belts, pulleys, gears, chains, sprccket-wheels, other dangerous moving parts of machinery which either form part of the machinery or are used in association with it shall be securely guarded. 4. Openers and pickers. - (1) In all opening or picker machines, beaters and other dangerous parts shall be securely fenced by suitable guard so as to prevent contact with them. Such guards and doors or cover or openings giving access to any dangerous part of the machinery shall be provided with inter locking arrangement : Provided that in the case of doors or covers of opening giving access to any dangerous part, other than beater covers, instead of the interlocking arrangement, such openings may be so fenced by guards which prevent access to any such dangerous part and which is either keep positively locked in position or fixed in such a manner that it cannot be removed without the use of hand tools. (2) The feed reels on all opening and picking machinery shall be covered with a guard designed to prevent the operator from reaching the nip while, the machinery is in operation. (3) The lap forming rollers shall be fitted with a guard or cover which shall prevent access to the nip at the intake of the lap-roller and fluted roller as long as the weighted rack is down. The guard or cover shall be locked that it cannot be raised until the machine is stopped, and the machine cannot be started until the cover or guard is closed : Provided that the foregoing provision shall not apply to the machines equipped with automatic lap forming devices : Provided further that any such machine equipped with an automatic lap forming device shall not be used unless the automatic lap forming device is in efficient working order. 5. Cotton Cards. - (1) All cylinder doors shall be secured by an interlocking arrangement which shall prevent the door being opened until the cylinder has ceased to revolve and shall render it impossible to restart the machine until the door has been closed : Provided that the later requirement in respect of the automatic locking device shall not apply while stripping or grinding operations are carried out : Provided further that stripping or grinding operations shall be carried out only by specially trained adult workers wearing tight fitting clothing whose names have been recorded in the register prescribed in this behalf as required in sub-section (1) of Section 22. (2) The licker-in shall be guarded so as to prevent access to the dangerous parts. (3) Every card shall be equipped with an arrangement that would enable the card cylinder to be driven by power during stripping-grinding operations without having to either shift the main belt to the fast pulley of the machine or to dismantle the interlocking meachanism. Such an arrangement shall be used only for stripping or grinding operations. 6. Garnett machines. - (1) Garnett licker-in shall be enclosed. (2) Garnett fancy rolls shall be enclosed by guards. These shall be installed in a way that keeps worker rolls reasonably accessible for removal adjustment. (3) The underside of the Garnett shall be guarded by a screen mesh or other form of enclosures to prevent success. 7. Gill boxes. - (1) The feed end shall be guarded so as to prevent fingers being caught in the pins of the intersecting followers. (2) All nips of in running rolls shall be guarded by suitable nip guards conforming to the following specifications. Any opening which the guard may permit when fitted in position shall be so restricted with respect to the distance of the opening from any nip point through that opening and in any circumstances the maximum width of the opening shall not exceed the following :- Distance of opening from nip point Maximum width of opening (1) (2) 0 to 38 mm 6 mm 39 to 63 mm 10 mm 64 to 88 mm 13 mm 89 to 140 mm 15 mm 141 to 165 mm 19 mm 166 to 190 mm 22 mm 191 to 215 mm 32 mm 8. Silver and ribbon lappers (cotton). - The calender drums and the lap spool shall be provided with a guard to prevent access to the nip between the in-running rolls. 9. Speed frames. - Jack box gills at the head stock shall be guarded and the guard shall have interlocking arrangement. 10. Spinning mules. - Wheels on spinning mule carriage shall be provided with substantial wheel guards, extending to within 6 mm of the rails. 11. Warpers. - Swiveled double bar gates shall be installed on all warpers operating in excess of 410 per metres + min peripheral speed. These gates shall have interlocking arrangements, except for the purpose of inching or jogging : Provided that the top and bottom bars of the gate shall be at least 1.05 and 0.53 metres high from the floor or working platform, and the gate shall be located 38 mm from the vertical tangent to the beam head. 12. Slashers. - (1) Cylinder dryers. - (a) All open nips of in-running rolls shall be guarded by nip guard conforming to the requirements in paragraph 7(2). (b) When slashers are operated by control levers, these levers shall be connected to a horizontal bar or treadle located not more than 170 cm above floor to control the operation from any point. (c) Slashers operated by push bottom control shall have stop and start buttons located at each end of the machine, and additional buttons located on both sides of the machine at the size box and the delivery end. If calender rolls are used, additional buttons shall be provided at both sides of the machine at points near the nips, except when slashers are equipped with an enclosed dryer as in paragraph (b). (2) Enclosed hot air dryer. - (a) All open nips of the top squeezing rollers shall be guarded by nip guards conforming to the requirements in paragraph 7(2). (b) When slashers are operated by control levers these shall be connected to a horizontal bar or treadle located not more than 170 cm above the floor to control the operation from any point. (c) Slashers operated by push-but on control shall have stop and start buttons located at each end of the machine and additional stop and start buttons located on both sides of the machines at intervals spaced not more than 1.83 metres on centres. 13. Looms. - Each loom shall be equipped with suitable guards designed to minimise the danger from flying shuttles. 14. Valves of kiers, tanks and other containers. - (1) Each value controlling the flow of steam, injurious gases or liquid into a kier or any other tank or container into which a person is likely to enter in connection with a process, operation, maintenance or for any other purpose, shall be provided with a suitable locking arrangement to enable the said person to lock the value securely in the closed position and retain the key with him before entering the kier, tank or container. (2) Wherever boiling tanks, caustic tanks and any other containers from which liquids which are hot, corrosive or toxic may overflow or splash are so located that the operator cannot see the contents from the floor or working area, emergency shut, off valves which can be controlled from a point not subject to danger of splash shall be provided to prevent danger. 15. Shearing machines. - All revolving blades on shearing machines shall be guarded so that the opening between the cloth surface and the bottom of the guard will not exceed 10 mm. 16. Continuous bleaching range (cotton and rayon). - The nip of all in-running rolls on open width bleaching machine rolls shall be protected with a guard to prevent the worker from being caught at the nip. The guard shall extend across the entire length of the nip. 17. Mercerizing range (piece goods). - (1) A stopping device shall be provided at each end of the machine. (2) A guard shall be provided at each end of the frame between the in-running chain and the clip opener. (3) A nip guard shall be provided for the in-running rolls of the mangle and washers and the guard shall confirm to the requirements in paragraph 7(2). 18. Tender frames. - (1) A stopping device shall be provided at each end of the machine. (2) 'A' guard shall be provided at each end of the machine frame at the in-running chain and clip opener. 19. Paddlers. - Suitable nip guards conforming to the requirements in paragraph 7(2) shall be provided to all dangerous in-running rolls. 20. Centrifugal extractors. - (1) Each extractor shall be provided with a guard for the basket, and the guard shall have inter-locking arrangement. (2) Each extractor shall be equipped with a mechanically or electrically operated brake to quickly stop the basket when the power driving the basket is shut-off. 21. Squeezer or wringer extractor, water mangle, back washer (worsted yarn) crabbing machines, and (decatising machines). - All in-running rolls shall be guarded with nip conforming to the requirements in paragraph 7(2). 22. Sanforizing and palmer machine. - (1) Nip guards shall be provided on all accessible in-running rolls and these shall conform to the requirements in paragraph 7(2). (2) Access from the sides to the nips of in-running rolls should be fenced by suitable side guards. (3) A safety trip rod, cable or wire centre cord shall be provided across the front and back of all palmer cylinder extending the length of the face of the cylinder. It shall operate readily whether pushed or pulled. The safety trip shall not be more than 170 cm. above the level at which the operator stands and shall be readily accessible. 23. Rope washers. - (1) Splash guards shall be installed on all rope washers unless the machine is so designed as to prevent the water or liquid from splashing on the operator, the floor, or working surface. (2) A safety trip rod, cable or wire centre cord shall be provided across the form the back of all rope washers extending the length of the face of the washer. It shall operate readily whether pushed or pulled. This safety trip shall be not more than 170 cm. above the level on which the operator stand shall be readily accessible. 24. Laundry washer tumbler or shaker. - (1) Each drying tumbler, each double cylinder shaker or clothes tumbler and each washing machine shall be equipped with an inter-locking arrangement which will prevent the power operation of the inside cylinder when the outer door on the case or the shell is open, and which will also prevent the outer door on the case or the shell from being opened without shutting off the power and the cylinder coming to stop. This should not prevent the movement of the inner cylinder by means of a hand operated machinism or an inching device. (2) Each closed barrel shall also be equipped with adequate means for holding open the doors or covers of the inner and outer cylinders or shells while it is being loaded or unloaded. 25. Printing machine (roller type). - (1) All in-running rolls shall be guarded by nip guards conforming to the requirements in paragraph 7(2). (2) The engraved roller gears and the large crown wheel shall be guarded. 26. Calenders. - The nip at the in-running side of the rolls shall be provided with a guard extending across the entire length of the nip and arranged to prevent the fingers of the workers from being pulled in between the rolls or between the guard and the rolls, and so constructed that the cloth can be fed into the rolls safely. 27. Rotary staple cutters. - The cutter shall be protected by a guard to prevent hands reaching the cutting zone. 28. Plaiting machines. - Access to the trap between the knife and card-bar shall be prevented by a guard. 29. Hand baling machines. - An angle iron handle-stop guard shall be installed at right angle to the frame of the machine. The stop guard shall be so designed and so located that it will prevent the handle from travelling beyond the vertical position should the handle slip from the operator's hand when the pawl has been released from the teeth of the take-up-gear. 30. Flat-work-ironer. - Each flat work or coller ironer shall be equipped with a safety bar or other guard across the entire from of the feed or first pressure rolls, so arranged that the striking of the bar or guard by the hand of the operator or other person will stop the machine. The guard shall be such that the operator or other person cannot reach into the rolls without removing the guard. This may be either a vertical guard on all sites or a complete cover. If a vertical guard is used, the distance from the floor or working platform to the top of guard shall be not less than 1.83 metres. [Schedule 1-A] Jute Textiles 1. Fencing of machinery. - Fencing, guards or safety devices prescribed in respect of each individual machine shall be provided and maintained in good order. 2. Softening machines. - (a) A safety stopping device comprising a breast plate in front of the feed table to operate the belt striking gear by releasing an unbalanced weight. No device departing from the unbalanced weight principle will be deemed to conform to this rule unless it has been approved in writing by the Inspector. In the case of machines provided with an individual electric drive the device shall be arranged to act on a switch inserted, in the no-volt release circuit. (b) The feed table shall not be less than 6' length measured from the floor and extending at that height not less than-6' from the centre of the first cloth roller to the centre of the first pair of cast iron rollers. The table shall be provided with side guards reaching a height of not less than 4'-6" from the centre of the first pair of rollers, the height of the rest of the side guards shall not be less than 4' from the floor :- (c) the starting and stopping gear shall be arranged to comply with the following :- (i) Provision for stopping the machine at both the feed and delivery ends; (ii) Provision for starting the machine at the feed end only, the design shall be such that an operator at the feed end cannot start the machine without the co-operation of an operator at the delivery end; (iii) When a machine is stopped for clearing a jam or for attention otherwise, the starting gear shall be secured in the "Off" position at least by a lock operated by a removable key in possession of the person attending machine; (iv) The lever operating the unbalanced weight shall be securely fenced; (d) Sheet steel casing completely enclosing the side shafts i.e. the shafts and gears shall not be exposed on the underside. The casings shall be locked or secured by a device which will ensure-(i) that they cannot be opened while the machine is in motion, and (ii) that it will not be possible to start the machine unless they are closed. 3. Carding Machine. - (a) The underframe shall be guarded in such a manner that it will not be possible for operatives to obtain access underneath the machine until the cylinder has ceased to revolve. The lowest cross number of the frame shall come down to a point not more than 10" from the floor and all openings above this, large enough to permit of access underneath, shall be filled in with sheet steel or fitted with bars or rods spaced not more than 6" apart, Any part of this protection may be in the form of the door, but all such doors shall be controlled by a device which will ensure that they cannot be opened until the cylinder has come to rest and that the machine cannot be restarted until the doors are close : Provided that in the case of machines installed before 1st January, 1950 rigidly secured panels filling the underframe will be deemed to comply with it. (b) A guard with panels and sliding doors of sheet or closely spaced bars or rods enclosing the side gears, there shall be no opening at the underside of this protection for access to the gears, the sliding doors shall be controlled, by a device which will ensure that they cannot be opened until the cylinder has come to rest and that the machine can not be started until the doors are closed. (c) A sheet steel guard extending up to the centre line of the cylinder enclosing the stripper belts and pulleys shall be provided on all machines installed after 1st January, 1950. (d) An adequately strong and rigid set of bars or ords over the doffer roller, securely bolted in position. This guard must follow the radius of the roller, the space between the rods not to exceed 2" the distance from the doffer pin points to the underside of the rods to be 4" the space between the drawing pressing roller and the first rod not to exceed 2"; and the width of guard from 1st to the last rod to be not less than 12". (e) A hand or guard rail extending the full width of the drawing pressing roller, fitted in a convenient position in front of and higher than the roller. (f) Effective side guards to prevent operatives fingers being caught between the delivery roller and pressing ball. (g) When a machine is stopped for cleaning a jam or attention otherwise, the starting gear shall be secured in the "Off position at least by a lock operated by removable key in possession of the person attending the machine. 4. Drawing machine. - (a) A sheet steel guard completely closing the space between the bend rail and bottom of the retaining roller, the opening and closing of which shall be controlled by the starting gear, and the design to be such that the guard can not be opened while the machine is running. The guard plate shall swivel more or less about the centre of its height, and top edge shall swing innards towards the grill bars as the guard opens, and outwards as the guard closes : Provided that in the case of machines installed before 1st January, 1950, a fixed guard will be sufficient if the clearance between the top of the guard and the underside of the retaining roller does not exceed ⅜" : Provided further that in the case of machine with individual electric drive it will be sufficient if the guard is of the swiveling type and interlinked with the driving mechanism so that silver can not be fed into the grill, or the guard opened, before the machine is stopped, and that the machine can not be started up unless the guard is closed. (b) Sheet steel or cast iron guards completely enclosing the end gears, the design to be such that access to the gears in possible only by removing the guard in its entirety. If doors or movable panels are provided that: they shall be controlled by a locking device, operated by the starting gear, which will ensure that machine can not be started unless the guard is completely closed and that no movable part can be opened whilst the machine is in motion : Provided that in the case of machines installed before 1st January, 1950 a guard securely held in position by automatic catches to prevent opening by vibration but without the interlocking arrangements, wall be deemed to comply with it. (c) An efficiency guard which will prevent operatives fingers of hands being caught between the delivery roller and the pressing ball. (d) Starting and stopping gear so designed that the machine can be stopped by operatives on the feed and delivery sides, can be started only by an operative on the feed side but with the co-operation of the operative on the side and cannot be started by an operative on the delivery side. The device necessitating co-operation shall be engaged before the machine stops. (e) Shear pins driving the individual carriage shall be fitted to the opinion on the main block shaft and not to the opinion on the carriage back shaft. 5. Removing machine. - (a) Starting and stopping gear designed to embody the following :- (i) provision for stopping the machine on both the feed and delivery sides. (ii) Provision for starting the machine on delivery side only. (iii) A device on the deliver side which will automatically lock the belt striking gear in the "off" position. This device shall be such that the machine will not stop before the lock is engaged nor start before it is disengaged by a worker on the delivery side. (b) Sheet steel or cast iron guards completely enclosing the end gears, the design to be such that access to the gears is possible only by removing the guard in its entirety. If doors or movable panels are provided they shall be controlled by locking device, operated by the starting gear, which will ensure that the machines can not be started unless the guard it completely closed and that no movable part can be opened whilst the machine is in motion : Provided that in the case of machines installed before 1st January, 1950, a guard securely held in position by automatic catches to prevent opening by vibration, but without the interlock into arrangement, will be deemed to comply with it. (c) Shear pins driving individual carriages shall be fitted to the main back shaft and not to the opinion on the carriage back shaft. 6. Spinning frames. - (a) Access between the driving cylinders whilst in motion shall be prevented by providing a door at the pass end, so interconnected with the starting gear that neither side of the frame can be set in motion whilst the door is open and conversely, the door cannot be opened whilst either or both sides of the frame is or are running : Provided that in the case of machines installed before 1st January, 1950, hinged and well secured doors will be deemed to comply with it. (b) Sheet steel or cast iron guards completely enclosing the end gears the design to be such that access to the gears, is possible only by removing the guard in its entirety. It doors or movable panels are provided they shall be controlled by a locking device; operated by the starting gear, which will ensure that the machine cannot be started unless, the guard is completely closed and that no movable part can be opened whilst the machine is in motion : Provided that in the case of machines installed before 1st January, 1950, a guard securely held in position by automatic catches to prevent opening by vibration, but without the interlocking arrangement, will be deemed to comply with it. 7. Cop winding machine. - (a) Effective guards covering the driving off end gears. Hinged doors or panels will not be deemed to comply with this rule unless securely held in the closed position by automatic catches to prevent opening by vibrations. (b) Guards covering the spindle driving gears of such design that it will not be possible to remove them from position whilst the machine is in motion : Provided that in the case of machines installed before 1st January, 1950, guards rigidly secured by bolts or screws will be deemed to comply with it. 8. Roll winding machine. - Effective guards for traverse or other gears and came. Hinged doors or panels will not be deemed to comply with this rule unless securely held in the closed position by automatic catches to prevent opening by vibration. 9. Beaming and dressing machines. - (a) The fly wheel shall be of the disc type. (b) Cross and side shafts driving the starch rollers shall be enclosed in protecting tubes. (c) A guard securely anchored in position and protecting the nip between the top and bottom starch rollers. It shall have an aperture large enough to pass the yarn through but not the operative's hand. A hinged guard will not be deemed to be in compliance with this rule. (d) A guard protecting the nip between the yarn beam pressing roller and the outer lop weight roller, i.e., the top with roller on the side at which the beam is inserted and removed. (e) The space between any yarn guide roller and its adjacent steam cylinder must be not less than 3". 10. Looms. - (a) Sheet steel or cast iron guards protecting the crank and wiper shafts spur gears shall be provided. (b) The minimum clearance between the sley and the breast beam shall not be less than 2" (c) Yarn beams shall be placed on looms by mechanical or other means, Lifting into position by hand alone will not be deemed to comply with this rule. 11. Cropping machines. - Sheet steel guards protecting the spirals shall be provided. 12. Calendering machines. - (a) A strong and rigid guard, securely fixed in position, in front of the nip between the bottom cast iron roller and the paper roller on top of same. This guard shall be constructed in such manner that it will be impossible for the fingers of an operative to reach the nip through the aperture in the guard. (b) Safely rollers protecting the nip of the upper rollers. These rollers must be made of steel or wrought iron tube, as light as possible, add of not more than of 2 ½" external diameter. The safety roller shall ride on the under roller and be free to lift. It shall be set in such manner that the peripheral clearance between it and the upper roller, and between it and the under roller when the safety roller is fuller raised, will not permit of an operative's fingers reaching the nip. (c) Sheet steel panels shall be fitted on the machine gable to prevent access through same to the large spur wheel. (d) Lever weights shall be lowered into strong and rigid guards. 13. Cloth cutting machine. - A guard preventing access to the knife from the front, top or sides shall be provided. On the under side the knife shall be protected upto the maximum limit without interfering with the machine operation. 14. Lapping machine. - (a) Provision for starting the machine at the feed end only, the design shall be such that an operator at the feed end cannot start the machine without the co-cooperation of an operator at the delivery end and that he cannot interfere with the device necessitating co-operation. (b) A "sight panel" fitted to the feed table in such position that operator on either side of the machine can see through to the other side. (c) The hand wheel on the driving shaft shall be of the disc type and it shall be located at sufficient distance from the machine gable to permit of fencing being constructed between it and the lever mechanism operating the folder. (d) The treadle mechanism shall be such as to allow extraction of the maximum cloth lapped and no worker shall be required to go up on the machine table to force it down. 15. Sewing machine. - An apron plate shall be fitted in front of the feed chain and the plate shall be without holes or openings except for slots for the jockey pulleys. 16. Press pits. - When the press table in level with the floor the clearance between it and the floor shall not be less than 4". Schedule II Cotton Ginning and Pressing 1. Line Shaft. - The line shaft or second motion in cotton ginning factories, when below floor level, shall be completely enclosed by a continuous wall or unclimbable fencing with only so many openings as are necessary for access to the shelf for removing cotton seed, cleaning and oiling, and such openings shall be provided with gates or doors which shall be kept closed and locked. 2. Gin-house. - No person other than the gin feeder shall be permitted to clean cloth on or in the proximity of a gin roller where the machine of which it is a part, is in motion under power. 3. Press-house. - No person working on an opener in a pressing factory shall be permitted to feed the machine by means of his legs. All such workers shall wear tight clothing. 4. Cotton opener. - In all types of openers in use in pressing factories the slope of the feed table shall not be more than 1 in 10 in no case shall it consist of a smooth metal plate. The beater or toothed cotton openers in use in pressing shall be guarded by securely fixing across the feed end of the machine a strong guard of metal or wood with sides closed, not more than twelve inches above the lattice and not less than twenty inches in width so arranged that in no circumstances can a man's hand come in contact with the beaters or rollers. Schedule III Wood-working Machinery 1. Definitions. - For the purpose of this schedule- (a) "wood-working machine" means a circular saw, band saw, planning machine, chain mortising machine or vertical spindle moulding machine operating on wood or cork; (b) "circular saw" means a circular saw working in a bench (including a rack bench) but does not include a pendulum or similar saw which is moved towards the wood for the purpose of cutting operation; (c) "band saw" means a band saw, the cutting portion of which runs in vertical diction but does not include a long saw or band re-sawing machine; (d) "planing machine" means a machine for overhand planing or for thicknessing or for both operations. 2. Stopping and starting device. - An efficient stopping and starting device shall be provided on every wood-working machine. The control of this device shall be in such a position as to be readily and conveniently operated by the person incharge of the machine. 3. Space around machines. - The place surrounding every woodworking machine in motion shall be kept free from obstruction. 4. Floors. - The flour surrounding every wood-working machine shall be maintained in good and level condition, and shall not be allowed to become slippery, and as far as practicable, shall be kept free from chips or other loose material. 5. Training and supervision. - (1) No person shall be employed at a wood-working machine unless he has been sufficiently trained to work that class of machine, or unless he works under the adequate supervision of a person who has thorough knowledge of the working of the machine. (2) A person who is being trained to work on a wood-working machine shall be fully and carefully instructed as to the dangers of the machine and the precautions to be observed to secure safe working of the machine. 6. Circular saws. - Every circular saw shall be fenced as follows :- (a) Behind and in direct line with the saw there shall be a riving knife, which shall have a smooth surface, shall be strong, rigid and easily adjustable, and shall also conform to the following conditions :- (i) The edge of the knife nearer the saw shall form an area of a circle having a radius not exceeding the radius of the largest saw used on the bench. (ii) The knife shall be maintained as close as practicable to the saw. having regard to the nature of the work being done at the time, and at the level of the bench table the distance between the front edge of the knife and the teeth of the saw shall not exceed half an inch. (iii) For a saw of a diameter of less than 24 inches, the knife shall extend upwards from the bench table to within one inch of the top of the saw, and for a saw of a diameter of 24 inches or over shall extend upwards from the bench table to a height of at least nine inches. (b) The top of the saw shall be covered be covered by a strong and easily adjustable guard, with a flange at the side of the saw farthest from the fence. The guard shall be kept so adjusted that the said flange shall extend below the roots of the teach of the saw. The guard shall extend from the top of the riving knife to a point as low as practicable at the cutting edge of the saw. (c) The part of the saw below the bench table shall be protected by two plates of metal or other suitable material one on each side of the saw; such plates shall not be more than six inches apart, and shall extend from the axis of the saw outwards to a distance of not less than two inches beyond the teeth of the saw. Metal plates, if not beaded, shall be of a thickness of at least 1/10 inch, or if beaded be of a thickness of at least 1/20 inch. 7. Push sticks. - A push stick or other suitable appliance shall be provided for use at every circular saw and at every vertical spindle moulding machine to enable the work to be done without unnecessary risk. 8. Band saws. - Every band saw shall be guarded as follows :- (a) Both sides of the bottom pulley shall be completely encased by sheet or expanded metal or other suitable material. (b) The front of the top pulley shall be covered with sheet or expended metal or other suitable material. 9. Planing machines. - (1) A planing machine (other than a planing machine which is mechanically fed) shall not be used for overhands planing unless it is fitted with a cylindrical cutter block. (2) Every planing machines used for overhand planing shall be provided with a "bridge" guard, capable of covering the full length and breadth of the cutting slot in the bench, and so constructed as to the easily adjusted both in a vertical and horizontal direction. (3) The feed roller of every planing machines used for thicknessing, except the combined machine for overhand planing and thicknessing, shall be provided with an efficient guard. 10. Vertical spindle moulding machines. - (1) The cutter of every vertical spindle moulding machine shall be guarded by the most efficient guard having regard to the nature of the work being performed. (2) The wood being molded at a vertical spindle moulding machine shall, if practicable, be held in a jig or holder of such construction as to reduce as far as possible the risk of accident to the worker. 11. Chain mortising machines. - The chain of every chain mortising machine shall be provided with a guard which shall enclose the cutters as far as practicable. 12. Adjustment and maintenance of guards. - The guards and other appliances required under this Schedule shall be,- (a) maintained in an efficient state; (b) constantly kept in position while the machinery is in motion; and (c) so adjusted as to enable the work to be done without necessary risk. 13. Exemptions. - Paragraphs. 6, 8, 9 and 10 shall not apply to any wood-working machines in respect of which it can be proved to the satisfaction of the Inspector that other safeguards are provided, maintained and used which render the machine as safe as it would be if guarded in the manner prescribed in this schedule. [Schedule IV] Rubber and Plastic Mills 1. Definition. - (i) "Rubber and Plastic Mills" shall mean the machine with rollers used in breaking down, cracking washing, grating, mixing, refining and warming of rubber or rubber goods and plastic or plastic goods. (ii) A "Calender" shall mean the machines with rollers used for frictioning, sheeting, coating and spreading of rubber or rubber compounds and plastic or plastic compounds. Installation of machines. - Rubber and plastic mills shall be so installed that top of the front roll is not less than one metre above the floor or working level provided that in existing installations where the top of the front roll is below this height a strong rigid distance bar guard shall be fitted across the front of the machine in such position that the operator cannot reach the nip of roller from the normal working position of the operator. 2. Safety Devices. - (i) Rubber and plastic mills shall be equipped with- (a) Hoppers so constructed or guarded that it is impossible for the opera-tors to come into contact in any manner with the nip of the rolls, or (b) Horizontal Safety trip rods or tight wire cable across front and rear, which will when pushed or pulled operate instantly to disconnect the power and apply the brakes or to reverse the rolls, Safety-trip rods or tight wire cables on rubber mills shall extend across the entire length of the face of the rolls and shall be located not more than 170 centimetres above the floor or working level. (ii) Calender machines shall be equipped with- (a) Horizontal safety-trip rods or tight wire across both front and rear, which will when pushed or pulled operate instantly, to disconnect the power and apply the brakes of to reverse the rolls; (b) Safety-trip rods or tight wire cables on calender machines shall extend across the entire length of the face of the roll and shall be located not more than 170 centimetres above the floor or working level. (c) on each side of all calenders and near both ends of the face of the rolls there shall be a vertical tight wire cable connecting with the bar tripping mechanism at the top and fastened to the frame within 30 centimetres of the floor. These cable should be positioned at a distance of not more than 30 centimetres from the face of the roll and at a distance of not less than 25 milimetres from the calender frame. 3. Maintenance and safety devices. - Safety trip rods and tight wire cables on all rubber mills and calenders shall be examined and tested daily in the presence of the Manager or other responsible person and if any defect is disclosed by such examination and test the mill shall not be used until such defect has been remedied. 4. Injection Moulding Machines. - (a) An electrical interlocking arrangement shall be provided so that the moulds cannot be closed unless the front safety gate is fully closed and on opening the front safety gates, the moulds will stop automatically. (b) In addition to the above arrangement an hydraulic safety guard shall also be incorporated with the front safety gate. This shall prevent the tail stock mould plate from moving forward on opening of the front safety gate. (c) At the rear of the machine, there shall be provided either an efficient fixed guard or a sliding gate which shall be electrically interlocked with the movement of the mould plates in the manner of the front safety gate as required under (a) above, so as to prevent access to the danger zone of the moulds in motion from the rear. 5. Leather, Plastic and Rubber Stripper Machines. - Strippers for trimming or punching tanned hides, plastic or rubber sheets in leather making footwear manufacturing or in similar industries shall be provided with suitable devices which required simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade, punch or stripper cutter. Schedule V All Factories 1. Whenever practicable and deemed necessary by the Inspector, service platforms and gangways shall be provided for overhead shafting and where required by him these shall be securely fenced with guard rails and the boards. 2. Safe access shall be provided to all bearings, clutches belt, shifting levers and all such other appliances which are required to be handed or operated while the machinery is at work. 3. All ladders used in replacing belts or in attending similar overhead machinery shall be especially made for that work and provided with hooks or an effective non-skid device. 4. No transmission machinery in motion shall be cleaned by cotton waste, rags or similar material held in hand. 5. All belts shall be regularly examined to see that they are kept in proper tension. 6. Each water guage glass of a boiler shall be fitted with an efficient guard. [7. Tight fitting clothing. - A worker required to wear tight fitting clothing under sub-section (1) of Section 22 shall be provided by the occupier with such clothing which shall consist of at least a pair of closely fitting half sleeves shift or vest. Such clothing shall be returned to the occupier on termination of service or when new clothing is provided.] [Schedule VI] Centrifugal Machines 1. Definition. - "Centrifugal Machines" include centrifugal extractors, separators and driers. 2. Every part of the centrifugal machine shall be- (a) of good design and construction and of adequate strength; (b) properly maintained; and (c) examined thoroughly by a competent person at regular intervals. 3. Interlocking guard for drum of basket. - (1) The case housing the rotating drum or basket of every centrifugal machine shall be provided with a strong lid. The design and construction of the case as well the lid should be such that no access is possible to the drum or basket when the lid is closed. (2) Every centrifugal machine shall be provided with an efficient inter-locking device that will effectively prevent the lid referred to in sub-paragraph (1) from being opened while the drum or basket is in motion and prevent the drum or basket being set in motion while the lid is in the open position. 4. Braking arrangement. - Every centrifugal machine shall be provided with an effective braking arrangement capable of bringing the drum or basket to rest within as short a period of time as reasonably practicable after the power is cut-off. 5. Operating speed. - No centrifugal machine shall be operated at a speed in excess of the manufacture's rating which shall be legibly stamped at easily visible places both on the inside of the basket and on the outside of the machine casing. 6. Exceptions. - Sub-paragraph (2) of paragraph 3, paragraphs 4 and 5 shall not apply in case of too lung machines or similar machines used in the sugar manufacturing Industry. [Schedule VII] Power Press 1. Application. - The Schedule shall apply to all types of power presses including press brakes except when used for working hot metal. 2. Definition. - For the purpose of this Schedule,- (a) "approval" means approved by the Chief Inspector; (b) "fixed fencing"means fencing provided for the tools of a power press being fencing which has no moving part associated with or dependent upon the mechanism of a power press and include that part of a closed tool which acts as a guard; (c) "power press" means a machine used in metal or other industries for moulding, pressing, blanking, raising, drawing and similar purposes; (d) "safety device" means the fencing and any other safeguard provided for the tools of a power press. 3. Starting stopping mechanism. - The starting and stopping mechanism shall be provided with a safety stop so as to prevent over running of the press or descent of the ram during tool setting, etc. 4. Protection of tool and die. - (1) Each press shall be provided with a fixed guard with a slip plate on the underside enclosing the front and all sides of the tool. (2) Each die shall be provided with a fixed guard surrounding its front and sides, and extending to the back in the form of a tunnel through which the pressed article falls to the rear of press. (3) The design, construction and mutual position of the guards referred to in (1) and (2) shall be such as to preclude the possibility of the worker's hand or figures reaching the danger zone. (4) The machine shall be fed through a small aperture at the bottom of the die guard, but a wider aperture may be permitted for second or subsequent operations if feeding is done through a chute. (5) Notwithstanding anything contained in sub-clause (1) and (2) an automatic or an inter-locked guard may be used in place of fixed guard, but where such guards are used they shall be maintained in an efficient working condition and in any guard develops defect, the power press shall not be operated unless the defect of the guard is removed. 5. Appointment of persons to power presses for us. - (1) Except as provided in sub-paragraph (4), no person shall set, reset, adjust or try out the tools on a power press or install or adjust any safety device thereon, being installation or adjustment preparatory to production of die or carry out an inspection and test of any safety device thereof required by paragraph 8 unless he,- (a) has attained the age of eighteen; (b) has been trained in accordance with the sub-paragraph (2); and (c) has been appointed by the occupier of the factory to carry out those duties in respect of the class or description of power press of the class or description of safety device (as the case may be) belongs; and the name of the every such person shall be entered in a register in Form 34. (2) The training shall include suitable and sufficient practical instruction in the matters in relation to each type of power press and safety device in respect of which it is proposed to appoint the person being trained. 6. Examination and testing of power press and safety devices. - (1) No power press or safety device shall be taken into use in any factory for the first time in the factory, or in case of a safety device for the first time on any power press, unless it has been thoroughly examined and tested, in the case of a power press, after installation in the factory, or in the case of a safety device when in position on the power press in connection with which it is to be used. (2) No power press shall be used unless it has been thoroughly examined and tested by a competent person, within the immediately preceding period of twelve months. (3) No power press shall be used unless every safety device (other than fixed fencing) thereon has within the immediately preceding period of six months when in position on that power press, been thoroughly examined and tested by a competent person. (4) The competent person carrying out an examination and test under the foregoing provisions shall make a report of the examination and test containing the following particulars and every such report shall be kept readily available for inspection- (a) name of the occupier of the factory; (b) address of the factory; (c) identification number or mark sufficient to identify the power press or the safety device; (d) date on which the power press or the safety device was first taken into use in the factory; (e) the date of each periodical thorough examination carried out as per requirement of sub-paragraph (2) above; (f) particulars of any defects effecting the safety working of the power press or the safety device found at any such thorough examination and steps taken to remedy such defects. 7. Defects disclosed during a thorough examination and tests. - (1) Where any defect is disclosed in any power press or in any safety device by any examination and test under paragraph 6 and in the opinion of the competent person carrying out the examination and test, either- (a) the said defect is a cause of danger to workers and in consequence the power press or safety device (as the case may be) ought not to be used until the said defect has been remedied, or (b) the said defect may become a cause of danger to workers and in consequence the power press or safety device (as the case may be) ought not to be used after the expiration of a special period unless the said defect has been remedied such defect shall, as soon as possible after the completion of the examination and test, be notified in writing by the competent person to the occupier of the factory and, in the case of defect falling within clause (b) of this sub-paragraph such notification shall include the period within which, in the opinion of the competent person, the defect ought to be remedied. (2) In every case where notification has been given under this paragraph, a copy of the report made under paragraph 6 (4) shall be sent by the competent person to the Inspector of the area within fourteen days of the completion of the examination and test. (3) Where any such defect is notified to the occupier in accordance with the foregoing provisions of this paragraph the power press or safety device (as the case may be) having the said defect shall not be used (a) in the case of a defect falling within clause (a) of sub-paragraph (1) until the said defect has been remedied; and (b) in the case of defect falling within clause (b) of sub-paragraph (1), after the expiration of the period the said defect has been remedied. (4) As soon as is practicable after any defect of which notification has been given under sub-paragraph (1) has been remedied, a record shall be made by or on behalf of the occupier stating the measures by which and the date on which the defect was remedied. 8. Inspection and test of safety devices. - (1) No power press shall be used after the setting, re-setting or adjustment of the tools thereon unless a person appointed or authorised for the purpose under paragraph 5 has inspected and tested every safety device thereon while it is in position on the said power press : Provided that an inspection, test and certificate as aforesaid shall not be required where any adjustment of the tools has not caused or resulted in any alteration to or disturbance of any safety device on the power press and if, after the adjustment of the tools, the safety devices, remain, in the opinion of such a person as aforesaid, in efficient working order. (2) Every power press and every safety device thereon while it is in position on the said power press shall be inspected and tested by a trained person every day. 9. Defects disclosed during an inspection and test. - (1) Where it appears to any person as a result of any inspection and test carried out by him under paragraph 8 that any necessary safety device is not in position or is not properly set in position on a power press or that any safety device which is in position on a power press is not in his opinion suitable, he shall notify the manager forthwith. (2) Except as provided in sub-paragraph (3) where any defect is disclosed in a safety device by any inspection and test under paragraph 7, the person carrying out the inspection and test shall notify the manager forthwith. (3) Where any defect in a safety device is the subject of a notification in writing under paragraph 7 by virtue of which the use of the safety device may be continued during a specified period without the said defect having been remedied, the requirement in sub-paragraph (2) of this paragraph shall not apply the said defect until the said period has expired. 10. Identification of power presses and safety devices. - For the purpose of identification every power press and every safety device provided for the same shall be distinctively and plainly marked. 11. Training and instructions to operators. - The operators shall be trained and instructed in the safe method of work before starting work on any power press. 12. Exemptions. - (1) If in respect of any factory, the Chief Inspector is satisfied that owing to the circumstances or infrequency of the processes of for any other reason, all or any of the provisions of this Schedule are not necessary for the protection of the workers employed on any power press of any class or description of power press or in the factory, the Chief Inspector may by a certificate in writing (which he may in his discretion revoke at any time), exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. (2) Where such exemption is granted, a legible copy of the certificate, showing the conditions (if any) subject to which it has been granted, shall be kept posted in the factory in a position where it may be conveniently read by the persons employed. [Schedule VIII] Shears, Slitters and Guillotine Machines 1. Definitions. - For the purpose of this Schedule- (a) "guillotine" means a machine ordinarily equipped with straight, bevel-edged blade operating vertically against a stationary resisting edge and used for cutting metallic or nonmetallic substances; (b) "shears" or "shearing machine" means a machine ordinarily equipped with straight, bevel-edged blades operating vertically against resisting edges, or with rotary, overlapping cutting wheels and used for shearing metals or non-metallic substances; (c) "slitter" or "slitting machine" means a machine ordinarily equipped with circular disctype knives, and used for trimming or cutting into metal or non-metallic substances or for slitting them into narrow strips; for the purpose of this schedule, this term includes bread or other food slicers equipped with rotary knives or cutting discs. 2. Guillotine and Shears. - (1) Where practicable, a barrier guard of adequate strength shall be provided at the front of the knife, fastened to the machine frame and shall be so fixed as would prevent any part of the operator body to reach the descending blade from device, below or through the barrier guard or from the sides : Provided that in case of machines used in the paper printing and allied industries, where a fixed barrier metal guard is not suitable on account of the height and volume of the material being fed, there shall be provided suitable starting devices which require simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade. (2) At the back end of each machines, an inclined guard shall be provided over which the slit pieces would slide and be collected at a safe distance in a manner as would prevent a person at the back from reaching the descending blade. (3) Power driven guillotine cutters, except continuous feed trimmers, shall be equipped with- (a) starting devices which require the simultaneous action of both hands to start the cutting motion and of at least one-hand on a control during the complete stroke of the knife; or (b) an automatic guard which will remove the hands of the operator from the danger zone at every descent of the blade, used in conjunction with one-hand starting devices which require two distinct movements of the device to start the cutting motion, and so designed as to return positively to the non-starting position after each complete cycle of the knife. (4) Where two or more workers are employed at the same time on the same power driven guillotine cutter equipped with two hand control, the device shall be so arranged that each worker shall be required to use both hands simultaneously on the safety trip to start the cutting motion, and at least one-hand on a control to complete the cut. (5) Power driven guillotine cutters, other than continuous trimmer, shall be provided, in addition to the brake or other stopping mechanism, with an emergency device which will prevent the machine from operating in the event of failure of the brake when the starting mechanism is in the non-starting position. 3. Slitting Machines. - (1) Circular disc-type knives on machines for cutting metal and leather, paper, rubber, textiles or other non-metallic substances shall, if within reach of operators standing on the floor or working level, be provided with guards enclosing the knife edges at all times as near as practicable to the surface of the material, and which may either- (a) automatically adjust themselves to the thickness of the materials; or (b) be fixed or manually adjusted so that the space between the bottom of the guard and the material will not exceed 6 mm (¼ in.) at any time. (2) Portions of blades underneath the tables or benches of slitting machines shall be covered by guards. 4. Index cutters and Vertical Paper Slotters. - Index cutters, and other machines for cutting strips from the ends of books, and for similar operations shall be provided with fixed guards, so arranged that the fingers of the operators cannot come between the blades and the tables. 5. Corner Cutters. - Corner cutters, used in the manufacture of paper boxes, shall be equipped with- (a) suitable guard, fastened to the machines in front of the knives and provided with slots of performations to afford visibility of the operations; or (b) other guard equally efficient for the protection of the fingers of the workers. 6. Bank Knives. - Bank wheels on band knives, and all portions of the blades except the working side between the sliding guide and the table on vertical mechanics, shall be completely enclosed with hinged guards of sheet metal not less than 4 mm in thickness or of other material of equal strength. [Schedule IX] Agitators and Mixing Machines 1. Definition. - "Agitators and Mixing Machines" means a tank or other container equipped with power driven mixing arms, blades or paddle wheels fixed to revolvable shafts or other single mechanical devices for blending and stirring liquids with other liquids or with solid substances or combinations or these. 2.When the top of an open agitator tank, beater tank, tank or paddle tank or a similar vessel is less than 1 Metre above the adjacent floor or working level adequate standard railing shall be installed on all open sides. 3. Agitators and mixing machines shall be provided at the top or sides of the containers, vessels of the agitators and mixing machines, such openings shall be provided with standard grill guards as would prevent access of any part of the operators body coming in contact with agitator stirring or similar devices whilst in motion. 4.When discharge holes, openings, chutes or similar arrangements are provided at the bottom or at the sides of the container vessels of the agitator and mixing machines, they shall be so designed, shaped, guarded or situated as would prevent access of any part of operator's body coming in contact with agitating, stirring or similar devices, whilst in motion inside the vessel. Rule prescribed under sub-section (2) of Section 23

Previous and next

All provisions of The Factory rules 1962

Questions people ask

Is rule 59 of the Factory rules 1962 still in force?

No repeal of the Factory rules 1962 is recorded.