LawGrids logoLAWGRIDS.ORG

Appendix B, Punjab Factory Rules 1952: APPENDIX-B

Punjab Factory Rules 1952 - Appendix B

Text of appendix B

APPENDIX-B

APPENDIX-B [SEE CLAUSE 11] 1. Hazards: CAUTIONARY NOTICE Benzene and substances containing benzene (a) Benzene and substances containing benzene are harmful. (b) Prolonged or repeated breathing of benzene vapours may result in acute or chronic poisoning. (c) Benzene can also be absorbed through skin which may cause skin or other diseases. 2. Preventive measures: (a) Avoid breathing of benzene vapours. (b) Avoid prolonged or repeated contact of benzene with the skin. (c) Remove benzene soaked or wet clothing promptly. (d) If any time you are exposed to high concentration of benzene vapours and exhibit signs and symptoms such as dizziness, difficulty in breathing, excessive excitation and losing of consciousness, immediately inform your factory manager. (e) Keep all the containers of benzene closed (f) Handle, use and process benzene and substances containing benzene carefully in order to prevent their spillage on floor. (g) Maintain good housekeeping. 3. Protective equipment: (a) Use respiratory protective equipment in places where benzene vapours are present in high concentration. (b) In emergency, use self generating oxygen mask or oxygen or air cylinder masks. (c) Wear hand gloves, aprons, goggles and gum boots to avoid contact of benzene with your skin and body parts. 4. First-aid measures in case of acute benzene poisoning : (a) Remove the clothing immediately if it is wetted with benzene. (b) If liquid benzene enters eyes, flush thoroughly for at least 15 minutes with clean running water and immediately secure medical attention. (c) In case of unusual exposure to benzene vapour, call a physician immediately. Until he arrives, do the following :- (i) If the exposed person is conscious - (a) Move him to fresh air in open. (b) Lay down without a pillow and keep him quiet and warm. (ii) If the exposed person is unconscious - (aa) Lay him down preferably on the left side with the head low. (bb) Remove any false teeth, chewing gum, tobacco or other foreign objects which may be in his mouth. (cc) Provide him artificial respiration in case difficulty is being experienced in breathing. (dd) In case of shallow breathing or cyanosis (blueness of skin, lips, ears, finger nail beds), he should be provided with medical oxygen or oxygen carbon dioxide mixture. If needed, he should be given artificial respiration. Oxygen should be administered by a trained person only. Schedule – XXII Manufacturing process or operation in carbon disulphide plants 1. Application - This schedule shall apply to all electric furnaces in which carbon disulphide is generated and all other plants where carbon disulphide after generation, is condensed, refined and stored. This schedule is in addition to and not in derogation of any of the provisions of the Act and Rules made there under. 2. Construction, installation and operation- (1) The buildings in which electric furnaces are installed and carbon disulphide after generation is condensed and refined shall be segregated from other parts of the factory and shall be of open type to ensure optimum ventilation and the plant layout shall be such that only a minimum number of workers are exposed to the risk of any fire or explosion at any one time. (2) Every electric furnace and every plant in which carbon disulphide is condensed, refined and stored with all their fittings and attachments shall be of good construction, sound material and of adequate strength to sustain the internal pressure to which the furnace or the plant may be subjected to and shall be so designed that carbon disulphide liquid and gas are in closed system during their normal working. (3) The electric furnace supports shall be firmly grouted about 60 centimetres in concrete or by other effective means. (4) Every electric furnace shall be installed and operated according to manufacturers’ instructions and these instructions shall be clearly imparted to the personnel in charge of construction and operation. (5) The instructions regarding observance of correct furnace temperature, sulphur dose, admissible current or power consumption and periodical checking of charcoal level shall be strictly complied with. 3. Electrodes - (1) Where upper ring electrodes made of steel are used in the electric furnace, they shall be of seamless tube construction and shall have arrangement for being connected t cooling water system through a siphon built in the electrodes or through a positive pressure water-pump. (2) The arrangement for cooling water referred to in sub-paragraph (1) shall be connected with automatic alarm system which will actuate in the event of interruption of cooling water in the electrodes and give visible and audible alarm signals in the control room and simultaneously stop power supply for the furnace operation and to stop the further supply of water. The alarm system and the actuating device shall be checked every day. 4. Charcoal level indicator and vibrator – Means shall be provided on each electric furnace for indicating the correct level of charcoal in the furnace and vibrating the charcoal. This mean shall employed often as necessary to maintain correct charge and level of charcoal. 5. Charcoal separator - A cyclone type of charcoal separator shall be fitted on the off take pipe between the electric furnace and sulphur separator to prevent entry of pieces of charcoal into the condensers and piping. 6. Rupture discs and safety seal - (1) At least two rupture discs of adequate size which shall blow off at a pressure twice the maximum operating pressure shall be provided on each furnace and shall either be mounted directly on the top of the furnace or each through an independent pipe as close as possible to the furnace. (2) A safety water seal shall be provided and tapped from a point between the charcoal separator and the sulphur separator. 7. Pyrometer and manometers - (1) Each electric furnace shall be fitted with adequate number of pyrometers to give an indication of the temperature as correctly as reasonably practicable at various points in the furnace. The dials for reading the temperatures shall be located in the control room. (2) Manometers or any other suitable devices shall be provided for indicating pressure – (a) In the off take pipe before and after the sulphur separator; and (b) In primary and secondary condensers. 8. Check valves - All piping carrying carbon disulphide shall be fitted with check valves at suitable positions so as to prevent gas from flowing back into any electric furnace in the event of its shut down. 9. Inspection and maintenance of electric furnaces - (1) Every electric furnace shall be inspected internally by a competent person. (a) Before being placed in service after installation; (b) Before being placed in service after reconstruction or repairs; and (c) Periodically every time the furnace is opened for cleaning or de- or for replacing electrodes. (2) When an electric furnace is shut down for cleaning or de-- (a) The brick lining shall be checked for continuity and any part found defective removed; (b) After removal of any part of the lining referred to in (a) the condition of the shell shall be closely inspected; and (c) Any plates forming shall found corroded to the extent that safety of the furnace is endangered shall be replaced. 10. Maintenance of records - The following hourly records shall be maintained in a log book. (a) Manometer readings at the points specified in sub-paragraph 7(2); (b) Gas temperature indicated by pyrometers and all other vital points near the sulphur separator and primary and secondary condensers; (c) Water temperature and flow of water through the siphon in the electrodes; and (d) Primary and secondary voltages and current and energy consumed. 11. Electrical apparatus, wiring and fittings - All buildings in which carbon disulphide id refined or stored shall be provided with electrical apparatus, wiring and fittings which shall afford adequate protection from fire and explosion. 12. Prohibition relating to smoking - No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in buildings in which carbon disulphide is refined or stored, and a notice in the language understood by a majority of the workers shall be posted in the plant prohibiting smoking and carrying of matches, fire or naked light or other means of producing naked light or spark into such rooms. 13. Means of escape - Adequate means of escape shall be provided and maintained to enable persons to move to a safe place as quickly as possible in case of an emergency. At least two independent staircases of adequate width shall be provided in every building housing the furnaces at reasonable intervals at opposite ends. These shall always be kept clear of all obstructions and so designed to afford easy passage. 14. Warnings in case of fire - There shall be adequate arrangements for giving warnings in case of fire or explosion which shall operate on electrically and in case of failure of electricity by some mechanical means. 15. Fire-fighting equipment - (1) Adequate number of suitable fire extinguishers or other fire-fighting equipment shall be kept in constant readiness for dealing with risks involved and depending on the amount and nature of materials stored. (1) (2) Clear instructions as to how the extinguishers or other equipment should be used printed in the language which the majority of the workers employed understand, shall be affixed to each extinguisher or other equipment and the personnel trained in their use. 16. Bulk Sulphur - (1) Open or semi-enclosed spaces for storage of bulk sulphur shall be sited with due regard to the dangers which may arise from sparks given off by nearby locomotives, etc., and precautions shall be taken to see that flames, smoking and matches and other sources of ignition do not come in contact with the clouds of dust arising during handling of bulk sulphur. (2) All enclosures for bulk sulphur shall be of non-combustible construction, adequately ventilated and so designed as to provide a minimum of ledges on which dust may lodge. (3) The bulk sulphur in the enclosures shall be handled in such a manner as to minimise the formation of dust clouds and no flame, smoking and matches or other sources of ignition shall be employed during handling and non-sparking tools shall be used whenever sulphur is shovelled or otherwise removed by hand. (4) No repairs involving flames, heat or use of hand or power tools shall be made in the enclosure where bulk sulphur is stored. 17. Liquid sulphur - Open flames, electric sparks and other sources of ignition, including smoking and matches, shall be excluded from the vicinity of molten sulphur. 18. Training and supervision - (1) All electric furnaces and all plants in which carbon disulphide is condensed, refined or stored shall be under adequate supervision at all times while the furnaces and plant are in operation. (2) Workers in charge of operation and maintenance of electric furnaces and the plants shall be properly qualified and adequately trained. 19. Washing facilities - (1) The occupier shall provide and maintain in a clean state and in good repair, for the use of all persons employed wash place under cover with at least one tap or stand-pipe, having a constant supply of clean water for every five such persons, the taps or stand-pipes being spaced not less than 120 centimetres apart with a sufficient supply of soap and clean towels, provided that towels shall be supplied individually to each worker if so ordered by the Inspector. (2) All the workers employed in the sulphur storage, handling and melting operations shall be provided with a nail brush. 20. Personal protective equipment - (1) Suitable goggles and protective clothing consisting of overalls without packets, gloves and foot-wear shall be provided for the use of operatives – (a) when operating valves or cocks controlling fluids etc., (b) drawing off a molten sulphur from sulphur pots; (c) handling charcoal or sulphur. (2) Suitable respiratory protective equipment shall be provided and stored in the appropriate place for use during abnormal conditions or in an emergency. (3) Arrangements shall be made for proper and efficient cleaning of all such protective equipment. 21. Cloakrooms - There shall be provided and maintained for the use of all persons employed in the processes a suitable cloakroom for clothing put off during work hours and a suitable place separate from the cloakroom for the storage or overalls or working clothes. The accommodation so provided shall be placed in the charge of a responsible person and shall be kept clean. 22. Unauthorized persons - Only maintenance and repair personnel, persons directly connected with the plant operation and those accompanied by authorized persons shall be admitted into the plant. Schedule – XXIII Operations involving high noise levels 1. Application - This schedule shall apply to all operations in any manufacturing process having high noise level. 2. Definitions - For the purpose of this schedule - (a) “Noise” means any unwanted sound. (b) ”High noise level” means any noise level measured on the A-weighted scale is 90 dB or above. (c) ”Decibel” means one-tenth of “Bel” which is the fundamental division of a logarithmic scale used to express the ratio of two specified or implied quantities, the number of “Bels” denoting such a ratio being the logarithm to the base the of 10 of this ratio. The noise level (or the sound pressure level) 6 corresponds to a reference pressure of 20 x 10 power(-6) Newton per square meter or 0.0002 dynes per square centimetre which is the threshold of hearing, that is, the lowest sound pressure level necessary to produce the sensation of hearing in average healthy listeners. The decibel in abbreviated form is dB. (d) ”Frequency” is the rate of pressure variations expressed in cycles per second or hertz. (e) ”dBA” refers to sound level in decibels as measured on a sound level meter operating on the A-weighting net work with slow meter response. (f) ”A-weighting” means making graded adjustments in the intensities of sound of various frequencies for the purpose of noise measurement, so that the sound pressure level measured by an instrument reflects the actual response of the human ear to the sound measured. 3. Protection against noise – (1) In every factory, suitable, a suitable engineering control or administrative measures shall be taken to ensure, so far as is reasonably practicable, that no worker is exposed to sound levels exceeding the maximum permissible noise exposure levels specified in Tables 1 and 2. Table 1 Permissible exposure in cases of continuous noise Total time of exposure (continuous dBA Sound pressure level in or a per day, in hours number of short term exposures) 8 90 6 92 4 95 3 97 2 100 1 ½ 102 1 105 ¾ 107 ½ 110 ¼ 115 Notes: 1. No exposure in excess of 115 dBA is to be permitted. 2. For any period of exposure falling in between any figure and the next higher or lower figure as indicated in column 1, the permissible sound pressure level is to be determined by extrapolation on a proportionate basis. Table 2 Permissible exposure levels of impulsive or impact noise Peak sound pressure level in dB Permitted number of impulses or impact per day 140 100 135 315 130 1,000 125 3,160 120 10,000 Notes: 1. No exposure in excess of 140 dB peak sound pressure level is permitted. 2. For any peak sound pressure level falling in between any figure and the next higher or lower figure as indicated in column 1, the permitted number of impulses or impacts per day is to be determined by extrapolation on a proportionate basis. (3) For the purposes of this schedule, if the variations in the noise level involve maximum at intervals of one second or less, the noise is to be considered as a continuous one and the criteria given in Table 1 would apply. In other cases, the noise is to be considered as impulsive or impact noise and the criteria given in Table 2 would apply. (3) When the daily exposure is composed of two or more periods of noise exposure at different levels their combined effect should be considered, rather than the individual effect of each. The mixed exposure should be considered to exceed the limit value if the sum of the fractions C1/T1 + C2/T2 +. ........... Cn/Tn exceeds unity, - Where the C1, C2 etc. indicate the total time of actual exposure at a specified noise level and T1, T2, etc. denote the time of exposure of less than 90 dBA may be ignored in the above calculation. (4) Where it is not possible to reduce the noise exposure to the levels specified in sub-rule (1) by reasonably practicable engineering control or administrative measures, the noise exposure shall be reduced to the greatest extent feasible by such control measures, and each worker so exposed shall be provided with suitable ear protectors so as to reduce the exposure to noise to the levels specified in sub-rule (1). (5) Where the ear protectors provided in accordance with sub-paragraph (2) and worn by a worker cannot still attenuate the noise reaching near his ear, as determined by subtracting the attenuation value in dBA of the ear protectors concerned from the measured sound pressure level, to a level permissible under Table 1 or Table 2 as the case may be, the noise exposure period shall be suitably reduced to correspond to the permissible noise exposures specified in sub-paragraph (1). (6) (a) In all cases where the prevailing sound levels exceed the permissible levels specified in sub-paragraph (1) there shall be administered an effective hearing conservation programme which shall include among other hearing conservation measures, pre-employment and periodical auditory surveys conducted on workers exposed to noise exceeding the permissible levels, and rehabilitation of such workers either by reducing the exposure to the noise levels or by transferring them to places where noise levels are relatively less or by any other suitable means. (b) Every worker employed in areas where the noise exceeds the maximum permissible exposure levels specified in sub-rule (1) shall be subjected to any auditory examination by a Certifying Surgeon within 14 days of his first employment and thereafter, shall be re-examined at least once a every 12 months. Such initial and periodical examinations shall include tests which the Certifying Surgeon may consider appropriate and shall include determination of auditory thresholds for pure tones of 125, 250, 500, 1000, 2000, 4000 and 8000 cycles per second. Schedule – XXIV Manufacture or manipulation of dangerous pesticides 1. Application - This schedule shall apply in respect of all factories or any part thereof in which the process of manufacture or manipulation of dangerous pesticide hereinafter referred to as the said manufacturing process is carried on. 2. Definitions - For the purpose of this Schedule - (a) “dangerous pesticides” means any product proposed or used for controlling, destroying or repelling any pest or for preventing growth or mitigating effects of such growth including any of its formulations which is considered toxic under and is covered by the Insecticides Act, 1968 and the rules made there under and any other product, as may be notified from time to time by the State Government; (b) “manipulation” includes mixing, blending, formulating, filling, emptying, packing or otherwise handling; (c) “efficient exhaust draught” means localised mechanical ventilation for removal of smoke, gas, vapour, dust, fume or mist so as to prevent them from escaping into the air of any work room in which work is carried on. No exhaust draught shall be considered efficient if it fails to remove smoke generated at the point where such gas, fume, dust, vapour or mist originates from the process. 3. Instruction to workers - Every worker on his first employment shall be fully instructed on the properties including dangerous properties of the chemicals handled in the said manufacturing process and the hazards involved. The employees shall also be instructed in the measures to be taken to deal with any emergency. Such instructions shall be repeated periodically. 4. Cautionary notice and placards - Cautionary notices and placards in the form specified in appendix to this schedule and printed in the language of the majority of the workers shall be displayed in all work places in which said manufacturing process is carried on so that they can be easily and conveniently read by the workers. Arrangements shall be made by the occupier and the manager of the factory to periodically instruct the workers regarding the health hazards arising to in the said manufacturing process and methods of protection. Such notices shall include brief instructions regarding the periodical clinical tests required to be undertaken for projecting health of the workers. 5. Prohibition relating to employment of women or young persons - No woman or young person shall be employed or permitted to work in any room in which the said manufacturing process is carried on or in any room in which dangerous pesticide is stored. 6. Food drinks, and smoking prohibition - (1) No food, drink, tobacco, pan or supari shall be brought into or consumed by any worker in any workroom in which the said manufacturing process is carried out. (2) Smoking shall be prohibited in any workroom in which the said manufacturing process is carried out. 7. Protective clothing and protective equipment - (1) Protective clothing consisting of long pants and shirts or overalls with long sleeves and head coverings shall be provided for all workers employed in the said manufacturing process. (2) (a) Protective equipment consisting of rubber gloves, gum boots, rubber aprons, chemical safety goggles and respirators shall be provided for all workers employed in the said manufacturing process. (b) Gloves, boots, aprons shall be made from synthetic rubber where a pesticide contains oil. (3) Protective clothing and equipment shall be worn by the workers supplied with such clothing and equipment. (4) Protective clothing and equipment shall be washed daily from inside and outside if the workers handle pesticides containing nicotine or phosphorous and shall be washed frequently if handling other pesticides. (5) Protective clothing and equipment shall be maintained in good condition. 8. Floors and work-benches - (1) Floors in every workroom where dangerous pesticides are manipulated shall be of cement or other impervious material giving a smooth surface. (2) Floors shall be maintained in good repair, provided with adequate slope leading to a drain and thoroughly washed once a day with the hose pipe. (3) Work-benches where dangerous pesticides are manipulated shall be made of smooth, non-absorbing material preferably stainless steel and shall be cleaned at least once daily. 9. Spillage and waste - (1) If a dangerous pesticide during its manipulation splashes or spills on the work-bench, floor or on the protective clothing worn by a worker, immediate action shall be taken for through decontamination of such areas or articles. (2) Cloth, rags, paper or other material soaked or soiled with a dangerous pesticide shall be deposited in a suitable receptacle with tight fitting cover. Contaminated waste shall be destroyed by burning at least once a week. (3) Suitable deactivating agents, where available, shall be kept in a readily accessible place for use while attending to a spillage. (4) Easy means of access shall be provided to all parts of the plant for cleaning, maintenance and repairs. 10. Empty containers used for dangerous pesticides - Containers used for dangerous pesticides shall be thoroughly cleaned of their contents and treated with an inactivating agent before being discarded or destroyed. 11. Manual handling - (1) A dangerous pesticide shall not be required or allowed to be manipulated by hand except by means of a long handled scoop. (2) Direct contact of any part of the body with a dangerous pesticide during its manipulation shall be avoided. 12. Ventilation - (1) In every workroom or area where a dangerous pesticide is manipulated, adequate ventilation shall be provided at all times by the circulation of fresh air. (2) Unless the process is completely enclosed, the following operations during manipulation of a dangerous pesticide shall not be undertaken without an efficient exhaust draught :- (a) emptying a container holding a dangerous pesticide; (b) blending a dangerous pesticide; (c) preparing a liquid or powder formulation containing a dangerous pesticide; and (d) Changing or filling a dangerous pesticide into a container, tank hopper or machine or small sized containers. (3) In the event of a failure of the exhaust draught provided on the above operation, the said operations shall be stopped forthwith. 13. Time allowed for washing - (1)Before each meal and before the end of the day’s work at least ten minutes in addition to the regular rest interval shall be allowed for washing to each worker engaged in the manipulation of dangerous pesticide. (2) Every worker engaged in the manipulation of dangerous pesticides shall have a thorough wash before consuming any food and also at the end of the day’s work. 14. Washing and bathing facilities - (1) There shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the factory where the said manufacturing process is carried on, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 5 persons employed. (2) The washing places shall have standpipes placed at intervals of not less than one meter. (3) Not less than one half of the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable material shall be provided : Provided that such towels shall be supplied individually for each worker is so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 15. Cloakroom - There shall be provided and maintained for the use of all workers employed in the factory where the said manufacturing process is carried on - (a) a cloakroom for clothing put off during working hours with adequate arrangements for drying clothing, if wet; and (b) separate and suitable arrangements for the storage of protective clothing provided under paragraph 7. 16. Mess room - (1) There shall be provided and maintained for the use of all workers employed in the factory in which the said manufacturing process is carried on and remaining on the premises during the rest intervals, suitable mess room which shall be furnished with - (a) sufficient tables and benches with back rest, and (b) Adequate means for warming food. (2) The mess room shall be placed under the charge of responsible person and shall be kept clean. 17. Manipulation not be undertaken - Manufacture or manipulation of a pesticides shall not be undertaken in any factory unless a certificate regarding its dangerous nature or otherwise is obtained from the Chief Inspector. 18. Medical facilities and records of examinations and tests - (1) The occupier of every factory to which this schedule applies, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of such examinations carried out by the medical practitioner shall be maintained in a separate, register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 19. Medical examination by certifying Surgeon - (1) every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examinations in respect of Halogenated Pesticides,shall include tests for determination of chemical in blood and in fat tissues, E.E.G. abnormalities and memory tests.In respect of organo phosphate compounds,such examinations shall include tests for depression of cholinesterase in plasma and red blood cells. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every six calendar months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include the tests specified in sub-paragraph (1). Further every worker employed in the said processes shall also be examined once in every three months by the factory medical officer. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraph (1) and (2), including the nature and the results of these test, shall also be entered by the certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 20. Exemption - If in respect of any factory the Chief Inspector is satisfied that owing to the exceptional circumstances or the infrequency of the said manufacturing process or for any other reason which shall record in writing all or any of the provisions of this schedule are not necessary for the protection of workers employed in the factory, he may by a certificate in writing exempt such factory, from all or any of the provisions on such condition as he may specify therein Insecticides and pesticides

Previous and next

All provisions of Punjab Factory Rules 1952

Questions people ask

Is appendix B of Punjab Factory Rules 1952 still in force?

No repeal of Punjab Factory Rules 1952 is recorded.