Form 351, Punjab Factories Rules 1952: FORM NO. 351
Punjab Factories Rules 1952 - Form 351
Text of form 351
FORM NO. 351
FORM NO. 351
(Prescribed under Rule, 112)
Inspection Book
Date and time of
inspection
Name of the
Inspecting Officer
Details of
violations
observed
Section of the
Factories Act
and Rules
violated
Remarks
including any
passed
inspecting Officer
1
2
3
4
5
GOVERNMENT OF PUNJAB
DEPARTMENT OF LABOUR
(LABOUR –II BRANCH)
Notification
28th February 2008
No.G.S.R 23/C.A.63/1948/Ss.64 and 112/2008-With reference to Punjab Government,
Department of Labour, Notification No.21/35/99-2Lab-II/1709 dated the 9th May, 2007 and in
exercise of the powers conferred by section 64 read with section 112 of the Factories Act, 1948
(Central Act No.63 of 1948), and all other powers enabling him in this behalf, the Governor of
Punjab is pleased to make the following rules, namely:-
RULES
(1) Short title, extent and duration. - (1) these rules may be called the Factories
(Punjab) Exempting Rules, 2008.
(2) They shall extend to the whole of the State of Punjab.
(3) They shall come into force on and with effect from the date of their publication in
the Official Gazette and shall remain in force for a period of five years from the date of their
enforcement.
2. Definitions. - In these rules, unless the context otherwise requires.-
a) “ Act” means the Factories Act, 1948 ;
b) “ Chief Inspector” means the Chief Inspector appointed under sub-section
(2) of Section 8;
c) “ Manager” means the person responsible to the occupier for the working
of the factory for the purposes of the Act;
d) “ Section” means a section of the Act;
e) “ Head of the Department” means an officer holding independent charge
of any department in any factory ; and
f) “Inspector” means the Inspector appointed under sub-section (1) of
section 8.
Section 64 3. Persons holding position of supervision or management or
confidential position etc.- The following persons in factories shall be deemed to hold
position of supervision or management and to be employed in confidential position:-
i) Managing Director, President, Chief Executive or Senior-Vice President,
Vice –President or General Manager;
ii) Deputy General Manager or Manger or Factory Manager ;
iii) Deputy Manager or Deputy Factory Manager, Assistant Manager or
Assistant Factory Manager ;
iv) Chief Welfare Officer or Welfare Officer or Lab our Welfare Officer;
v) Heads of Departments ;
vi) Superintending Engineer ;
vii) Executive Engineer or Assistant Engineer ;
viii) Secretary or Personal Assistant to the persons listed above at serial
numbers (i) to (vii) ;
ix) Sub-Station Engineer;
x) Head Electrician;
xi) Supervisor or Foreman;
xii) Head Store Keeper or Store keeper ;
xiii) Head Time-Keeper or Time keeper ;
xiv) Store Purchase Officer ; and
xv) any other person employed as such and so declared by the Chief Inspector
in writing.
Section 64 4. List to be maintained of persons holding confidential position or
position of supervision or management. - A list showing the names and designations
of all persons referred to in rule 3 shall be maintained in every factory.
Section 64 5. Exemption of certain adult workers.- (1) Adult workers engaged in
factories, specified in column 2 of the Schedule given below on the work specified in
column 3, are exempted from the provisions of the sections specified in column 4,
subject to the conditions, if any, specified in column 5 thereof.
(2) Except in the case of urgent repairs covered by item 1 of the said Schedule in which
case conditions (a) , (c) and (e) shall not apply, the exemption shall be subject to the
following conditions, namely:-
(a) in case of exemption from section 51 and 54, no worker shall work
for more than ten hours in a day or sixty hours in a week;
(b) in the case of exemption from section 55, sufficient time though not
fixed , shall be given for meals to the satisfaction of the Inspector
concerned;
(c) the total number of hours of overtime worked shall not exceed fifty
hours for any one quarter;
(d) the payment of wages for overtime work done shall be paid as
required by section 59; and
(e) The spread over inclusive of intervals for rest shall not exceed twelve
hours in any one day.
THE SCHEDULE
(See rule 5)
Section Class of Nature of Extent Conditions
Empowering Factories Work of exemption
The grant of
Exemption
1 2 3 4 5
64(2) (a) All Factories Urgent Sections (i) No Worker shall
And 64(3) repairs - 51, 52, 54, 55, be employed
The following 56 and 61 for more than
Shall be fifteen hour on
Considered any one day or
To be urgent thirty nine hours
Repairs, during any three
Namely: - consecutive days
(a) Repairs to any part or seventy
Of the the machinery hours during each
Plant or period of seven
Structure of consecutive days
Factory which are commencing from
Of such a nature his first employment
That delay in their on such repairs;
Execution would
involve danger to
human life or safety
or the stoppage of
manufacturing
process;
64(2) (b) (1) All (i) Work in the Section the exemption
And Factories machine, smithy 51, 54 shall be granted
64(3) or foundry shops 55, 56 only in respect
in connection and 61 of a limited
with the mill number of persons
gearing, electric to be given by the
driving or lighting Chief Inspector or
apparatus, mechanical application by
or electrical lifts the Manager
or steam or water through the
pipes or pumps; Inspector
concerned.
(ii) Work of exami- Section the exemption
nation or repairing 51, 54,55 shall be granted
any machinery or 56 and 61 only in respect
part of the plant of a limited
which is necessary number of
for carrying on the persons to
work in the factory; be given by the
and Chief Inspector
on application
by the Manager
through the
Inspector
concerned.
(iii) Work in engineer Section The exemption
room, boiler houses 51,54,55 shall be granted
and furnaces in 56 and 61 only in respect
rolling mills such as of a limited
lighting fires, in order number of persons
to generate steam or to be given by the
gas preparatory to the Chief Inspector on
commencement of application by the
regular work in the Manager through
factory. the Inspector
concerned.
2) Iron Steel Work in connection Section The exemption
Brass or with roll changing 54, 55 shall be granted
Copper 56 and 61 only in respect of
Rolling Mills a limited number
of persons to be
given by the Chief Inspector on application by the Manager through the
Inspector concerned.
(b) break-down, (ii) Within twenty-
repairs to motive, four hours of the
power transmission commencement of
or other essential the work, notice
plant of the factories shall be sent to the
collieries. Railways, Inspector describing
tramways, motor transport, the nature of the
gas, electrical generation urgent repair
and transmission, pumping stating the names
or a similar essential or of persons
public utility services employed and the
carried out in general exact time of
engineering works commencement
and foundries and of work and the
which are necessary probable period
to enable such units for its completion.
to maintain their main A copy of the
manufacturing processes above notice
production or services shall be
during normal working displayed at a
hours ; and conspicuous
place in the
factory before
the workers
are engaged on
urgent repairs;
(c) repairs in connection (iii) Exemption
with a change of motive from the provisions
power for example, from of section 54 shall
steam to electricity or vice apply only in the
versa, when such work case of male adult
cannot possibly be done workers;
without stoppage of the (iv) No worker shall
normal manufacturing be employed for
process; and more than 14
consecutive days
without a rest of
24 hours.
Explanation:
(d) “ Periodical cleaning”
is not included in the
terms “ examining” or
“repairing”
64(2) (c) All Factories (i) Work performed by Section 51 A notice describing
and 64 (3) workers on lighting, 54, 55,56 the system of work,
ventilating and and 61 change of shifts and
humidifying grant of weekly
apparatus; holidays, shall be
sent to the Inspector
and the Chief Inspector
in advance and no
change shall be made
without prior intimation to
the Inspector and the
Chief Inspector and further
subject to the provisions of
Section 61 and 63;
(ii) Work performed by A notice describing
fire pump men; and the system of work,
change of shifts and
(iii) Workers engaged in grant of weekly
loading or unloading or holidays shall be sent
transporting raw materials to the Inspector and
or finished articles in Chief Inspector in
factories where such advance and no
work is intermittent. change shall be made
without prior intimation to
the Inspector and the Chief
Inspector and further subject to
the provisions of sections 61 and 63.
64 ( 2) (d) All Factories Work relating to Sections 51 In the absence of a
(1)and 64(3) continuous 52,54,55 56 worker who has
process declared and 61 failed to attend to his
as such by chief duty, a shift worker
Inspector. be allowed to work
the whole or part of a
subsequent shift
Provided that.-(i) the next
shift of the worker shall not
commence before a period of
sixteenhours has elapsed;
(ii) within twenty four hours of
commencement of the
subseqent shift, a notice shall be
sent to the Inspector describing
the circumstances under which the
worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted
to the male adult workers only.
(2) Oil tank Work connected Sections 51, In the absence
of installations with pumping 52,54,55, a worker who
operations. 56 & 61 has failed to
attend to his duty, a
shift worker shall be
allowed to work the
whole or part of a
subsequent shift:
Provided that:-
(i) the next shift of the
worker shall not
commence before
a period of sixteen
hours has elapsed ;
(ii) within
twenty four hours
of the
commencement of
the subsequent
shift , a notice
shall be sent to the
Inspector
describing the
circumstances
under which the
worker is required
to work in the
subsequent shift;
and
(iii) the exemption
shall be restricted
to the male adult
workers only.
(3) Hydro or Continuous Section 51, In the
absence of
Thermal work for 52, 54 , 55 a worker who
power generating or 56 & 61 has failed to
generating transforming attend to his
or trans- electricity. duty, a shift
forming worker shall
be
stations allowed to
work the whole
or part of a
subsequent
shift;
Provided that .-
(i) the next shift of the
workers shall not
commence before
a period of sixteen
hours has elapsed;
(ii) within
twenty-four
hours of the
commencement
of the subsequent
shift, a notice
shall be sent
to the Inspector
describing the
circumstances
under which the
worker is required
to work in the
subsequent shift;
and
iii) the exemption
shall be restricted
to the male adult
workers only.
(4) Sugar (i) Work relating Section 51, In the absence of worker has failed
Factories to the extractions 52,54,55,56 to attend his duty, a shift worker shall
of juice and 61 be allowed to work the whole or part
from the cane of subsequent shift;
clarification,
evaporation or
boiling of juice;
,
(ii) Curing of Provided that .-
massecuites and (i) the next shift of the worker shall
not commence before a period of
sixteen hours has elapsed;
(iii) Bagging (ii) within twenty four hours of the
commencement of the subsequent
shift, a notice shall be sent to the
Inspector describing the circums-
tances under which the worker is
required to work in the subsequent
shaft; and
(iii) the exemption shall be restricted
to the male adult workers only.
(5) Distilleries Work-relating Section 51,52, In the absence of a worker who has
to ferment- 54,55,56 and 61. failed to attend to his duty, a shift
ation and workers shall be allowed to work the
distillation. whole or part of a subsequent shift;
Provided that.-
(i) the next shift of the worker shall
not commence before a period of
sixteen hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
a notice shall be sent to the Inspector
describing the circumstances under
which the workers is required to work in
the subsequent shift; and
(iii) the exemption shall be restricted
to the male adult workers only.
(6) Chemical (i) work Section 52,54 In the absence of a worker who has
factories connected and 55 failed to attend to his duty, a shift
with worker shall be allowed to work the
burning of whole or part of a subsequent shift.
sulphur, Provided that .-
ammonia-
tion, chlorination, (i) the next shift of the worker shall
carbonation not commence before a period of
preparation and sixteen hours has elapsed;
purification of
gases; and
(ii) Work on (ii) within twenty-four hours of the
reactors commencement of the subsequent
shift, a notice shall be sent to the
Inspector describing the circumstances
under which the worker is required to
work in the subsequent shift ; and
(iii) the exemption shall be restricted to the
male adult workers only.
(7) Hydroge- Work of Section 52 In the absence of a worker who has
neration refining, 54 and 55 failed to attend to his duty, a shift
of oil bleaching worker shall be allowed to work the
factories filtering, whole or part of a subsequent shift;
deodorizing,
generation of Provided that .-
hydrogen
compression of (i) the next shift of the worker shall not
gases and filling commence before a period of sixteen
of cylinders. hours has elapsed;
(ii) within twentyfour hours of the
commencement of the subsequent shift, a
notice shall be sent to the Inspector,
describing the circumstances under which th
worker is required to work in the subsequent
shift; and
(iii) the exemption shall be restricted to the male
adult workers only.
(8) Paper Work on Section 52, In the absence of a worker who has
Factories Choppers, 54 and 55 failed to attend to his duty, as shift
Kneaders, worker shall be allowed to work the
digestors, whole or part of a subsequent shift;
strainers,
washers, Provided that .-
beaters,
paper making (i) the next shift of the worker shall
machines, not commence before a period of
pumping plant, sixteen hours has elapsed;
reelers and
cutters. (ii) within twenty four hours of the
commencement of the subsequent shift;
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is requried to work in the
subsequent shift;
(iii) and the exemption shall be restricted
to the male adult workers only.
(9) Rubber Work on Section 51 In the absence of a worker who has
tyres curing 54, 55 and 56 failed to attend to his duty, a shift
factories worker shall be allowed to work the
whole or part of a subsequent shift;
Provided that .-
(i) the next shift of the workers shall not
commence before a period of sixteen
hours has elapsed.
(ii) within twenty four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is required to work in the
subsequent shift ; and
(iii) the exemption shall be restricted to
the male adult workers only.
(10) Muncipal, All workers Section In the absence of a worker who has
Public and engaged in 52 and 55 failed to attend to his duty, a shift
Railway continuous worker shall be allowed to work the
water & process work whole or part of a subsequent shift;
sewerage
pumping
stations.
Provided that .-
(i)the next shift of the worker shall not
commence before a period of sixteen hours
has elapsed;
(ii)within twenty four hours of the
commencement the subsequent shift, a
notice shall be sent to the Inspector ,
describing the circumstances under which
the worker is required to work in the
subsequent shift ; and
(ii) the exemption shall be restricted to the
male adult workers only.
(11) Tanneries Work of Section In the absence of a worker who has
soaking, liming, 52 & 55 failed to attend to his duty, a shift
washing, bathing, worker shall be allowed to work the
tanning and drying whole or part of a subsequent shift;
of hide a kios and skins.
Provided that .-
(i) the next shift of the worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only.
12) Bricks Work on Section 52 and In the absence of a worker who has
kiln burners 56 failed to attend to his duty, a shift
worker shall be allowed to work the whole
or part of a subsequent shift;
Provided that .-
(i) the next shift of the workers shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only.
13) Roller All work Section 52 and In the absence of a worker who has
Flour 56 failed to attend to his duty, a shift
Mills worker shall be allowed to work the
whole or part of a subsequent shift;
Provided that,-
(i) the next shift of the worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only
(14) Soap Working on Section 52 In the absence of a worker who has
soap boiling and and 55 failed to attend to his duty, a shift
soap drying pans. worker shall be allowed to work the
whole or part of a subsequent shift;
Provided that .-
(i) the next shift of the worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only.
15) Textile Work connected Sections In the absence of a worker who has
Dyeing with dyeing, 51,52,54 failed to attend to his duty, a shift
Factories bleaching, 55and 56 worker shall be allowed to work the
finishing and whole or part of a subsequent shift;
printing.
Provided that .-
(i) the next shift of worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only.
16) Rayon All work Section In the absence of a worker who has
Silk connected with 51,52,54 failed to attend to his duty, a shift
manufacture of 55 and 56 worker shall be allowed to work the
acerone and whole or part of a subsequent shift;
cellulose / acetate Provided that .-
producer, gas (i) the next shift of the worker shall
acetic acid, not commence before a period of
aldehide cellulose sixteen hours has elapsed;
dope. (ii) within twenty-four hours
commencement of the subsequent
shift, a notice shall be sent to the
Inspector, describing the circumstances
under which the worker is requried to
work in the subsequent shift; and .
(iii) the exemption shall be restricted to the
male adult workers only.
17) Glass Moulding and Section In the absence of a worker who has
Factories blowing 52 and 55 failed to attend to his duty, a shift
worker shall be allowed to work the
whole or part of a subsequent shift;
Provided that .-
(i) the next shift of worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shif
a notice shall be sent to the Inspector,
describing the circumstances under
which the worker is required to work
the subsequent shift; and
(iii)the exemption shall be restricted to the
male adult workers only.
18) Enamelling Work in Section In the absence of a worker who has
Works furnace 52 & 55 failed to attend to his duty , shift
enamelling worker shall be allowed to work the
whole or part of a subsequent shift;
Provided that .-
(i) the next shift of worker shall not
commence before a period of sixteen
hours has elapsed;
(ii) within twenty-four hours of the
commencement of the subsequent shift,
notice shall be sent to the Inspector,
describing the circumstances under whic
the worker is required to work in the
subsequent shift; and
(iii) the exemption shall be restricted to the
male adult workers only.
64 (2) (19) Fruit, All work Section Exemption from the provisions of
(d) and vegetables engaged in 51, 52, 54 section 61 of the Act, will apply in so
(64) (3) and continuous 55, 56 and 61 far as it relates to the specifications of
canning process the periods of rest intervals in the
Factories Work notice of work.
64(2) (20) Rice Work of Section Exemption from the provisions of
( f) and Mills persons 55 section 61 of the Act, will apply
64(3) engaged in so far as it relates to the
in boiling, specifications of the periods of
drying, rest intervals in the notice of work.
lifting and
storing of
paddy in
rice mills.
64(2) (21) News Breakdown Section (1) (i) The spread over shall not excee
(i) papers of 51, 54, twelve hours on any day;
& 64(3) Printing machinery 56 and 61 (ii) Notice shall be given to the
Press. Inspector concerned within
twenty four hours of the
occurrence whenever this exemption
is availed of in any emergency; and
(iii) Exemption from the provisions of
section 61 of the Act will apply in so fa
as it relates to the specifications of the
periods of rest intervals in the notice o
work periods.
(2) Every such worker shall be
allowed adequate time to take light
refreshments or meals at the place of
his employment in the room or place
specially provided for the purpose an
arranged in such a manner that it ma
not cause inconvenience to the
worker and at the same time may not
require stopping of any plant ,
machine or process or the normal
functioning of the factory.
(3) A notice describing the system of
work, change of shifts and grant of
weekly holidays shall be sent to the
Inspector and the Chief Inspector in
advance and no change shall be
made therein without the prior
intimation to the Inspector and the
Chief Inspector and subject further to
the provisions of Sections 61 and 63.
(22) All Loading Section (1) (i) The spread over shall not
Factories and un-loading 51,52 exceed twelve hours on any
of railway wagons, 54, 55 day;
lorries and trucks. and 61 (ii) Notice shall be given to the
Inspector concerned within
Twenty-four hours of the
occurrence whenever this exemption
is availed of in any emergency; and
(iii) Exemption from the provisions of
section 61 of the Act will apply in so fa
as it relates to the specifications of the
periods of rest intervals in the notice o
work periods.
(2) Every such worker shall be
allowed adequate time to take light
refreshments or meals at the place of
his employment in the room or place
specially provided for the purpose an
arranged in such a manner that it ma
not cause inconvenience to the
worker and at the same time may not
require stopping of any plant ,
machine or process or the normal
functioning of the factory.
(3) Every worker shall be allowed
at least one weekly holiday in
every week on the average and
whenever in any week the permitted
hours of work daily or weekly exceed,
extra wages for overtime on any
particular week shall be paid in
accordance with the provisions of
section 59.
64(2) (23) All Any work Sections (1) (i) The spread over shall not
(k) and factories which notified 51,52,54 exceed twelve hours on any day
64 (3) by the State 56 and 61 (ii) Notice shall be given to the
Government Inspectors concerned within
in Official twenty four hours of the
Gazette as a occurrence whenever this
work of national exemption is availed of in any
importance emergency ; and
(iii)Exemption from the provisions of
section 61 of the Act will apply in so fa
as it relates to the specifications of the
periods of rest intervals in the notice o
work periods.
(2) Every such worker shall be
allowed adequate time to take light
refreshments or meals at the place of
his employment in a room or a place
specially provided for the purpose an
arranged in such a manner that it ma
not cause inconvenience to the
worker and at the same time may not
require stopping of any plant ,
machine or process or the normal
functioning of the factory.
(3) Every worker shall be allowed
at least one weekly holiday in
every week on the average and
whenever in any week the permitted
hours of work daily or weekly exceed,
extra wages for overtime on any
particular day or in any particular week
shall be paid in accordance with the
provisions of section 59.
Dated, Chandigarh,
the
P.Ram,
Principal Secretary to Government of Punjab,
Department of Labour
Ends.No.21/35/99/2 Lab-II/ Dated, Chandigarh the
A copy is forwarded to the following :-
1. The controller Printing and Stationery, Punjab, Chandigarh with one spare copy with th
request that this notification may kindly be published in the next issue of Punjab Gov
gazette and supply 50 copies there of to the Government.
2 The Director of Factories Punjab, Chandigarh with reference to his No. P.A./924 date
31.01.2007 for information and necessary action.
Under Secretary.
THE PUNJAB WELFARE OFFICERS (RECRUITMENT AND CONDITIONS OF
SERVICE) RULES, 1952
1. Short title and commencement: -
(1) these rules may be called the Punjab Welfare Officers (Recruitment and conditions
of Service) Rules, 1952.
(2) They shall come in to force on such date as the State Government may, by
notification in the Official gazette, appoint in this behalf.
(3) Omitted
2. Definitions: - In these rules, unless the context otherwise requires: -
(a) “Act” means the Factories Act, 1948 (LXIII) of 1946;
(b) The expressions “factory” and Occupier” have the meaning respectively
assigned to them in the Act.
Number of Welfare Officers:- There shall be one Welfare Officer for factories employing five
hundred to two thousand workers. There shall be an additional Welfare Officer fore every
additional two thousand workers, or fraction there of over five hundred. Where there are more
than one Welfare officers one of them shall be appointed as the Chief Welfare Officer.
3-A. Pay scales and emoluments of Welfare Officer: - The Welfare Officers shall be entitled to
the scales of pay given below: - Category-1. For factories employing more more than 2,000
workers.
(I) Chief Welfare Officer: -
Rs. 7880-220-8100-275-10300-340-11660
(II) Welfare Officer: -
Rs. 7000-220-8100-275-10300-340-10980
Category-II. For factories employing 500 to 2,000 workers.
Welfare Officer:-
Rs. 7000-220-8100-275-10300-340-10980
Provided that: -
(a) “nothing in this rule shall be deemed to prevent the grant of scales of pay
higher than those specified above or affect the emoluments of the chief
Welfare Officers and Welfare Officers who are enjoying scales of pay
higher than those specified above and.
(b) the scales of pay mentioned above shall be exclusive of dearness
allowance and other allowances which shall be payable at such rates as
may, from time to time, be admissible to the Punjab Government
employees, enjoying the same pay.
4. Qualifications:- A person shall not be eligible for appointment as a Welfare Officer
unless he: -
(a) processes a degree of University recognized by the State Government in this
behalf;
(b) Has obtained a degree or Diploma in Social Science from any institution
recognized by the State Government in this behalf; and
(c) has adequate knowledge of the language spoken by the majority of the
workers in the factory to which he is to be attached.
Provided that in the case of a person who is acting as a welfare Officer at
the commencement of these rules the State Government may, subject to
such conditions as it may specify, relax the aforesaid qualifications.
5. Recruitment of welfare Officers:-
1. The post of a Welfare Officer shall be advertised in at least two news papers
having a wide circulation in the State one of which shall be a newspaper published in
English.
2. The selection shall be made from amongst the candidates applying for the
post by a committee appointed by the occupier of the factory.
3. The appointment when made shall be notified by the occupier to the state
Government or such authority as the State Government may specify for the
purpose, giving full details of the qualifications, etc., of the officer appointed and the
conditions of his service.
THE NAMES OF INSTITUTIONS, DEGREES AND DIPLOMAS
RECOGNISED BY STATE GOVERNMENT FOR THE PURPOSE OF RECRUITMENT OF
WELFARE OFFICERS TO BE EMPLOYED IN FACTORIES
UNDER THE FACTORIES ACT, 1948:-
1. Andhra University College, Weltair I) Diploma in Social Welfare
Ii) A degree of the Master of Science in
Social Welfare.
2. Department of Lab our & Social Welfare M.A. in Lab our and Social Welfare
Patna University.
3. St.Xavier Labour Relations Institutes Diploma in Industrial Relations& Welfare
Jamshedpur.
4. St.Xavier College, Ranchi Post Graduate Diploma in Social Service
5. Bhagalpur University M.A.in Labour and Social Welfare
6. University of Baroda Master in Social Work.
7. University of Gujrat Diploma in Labour Welfare
8. Delhi school of Social Work University M.A. In Social Work
Of Delhi.
9. University of Kerala Diploma in Social Service
10. Vikram University Ujjain (M.P.) M.A. In Sociology
11. Tata Instgitute of Social Science. Diploma in Social Service Administration.
12. Labour Welfare Workers Institute, Diploma in Lab our Welfare
University of Bombay.
13. Indian Institute of Social Order, Post Graduate Diploma in Social Service.
Poona
14. Shri Dorabji Graduate School of Diploma in Lab our Welfare
Social Work, Bombay, University of
Bombay.
15. University of Baroda A diploma of the faculty of Social work.
16. Institute of Lab our Welfare workers A diploma of the long term course of
Bombay the Institute.
17. University of Bombay M.A. Degree in Sociology
18. Madras School of Social work, Madras A Diploma in Social Service Administration
19. Loyals College, Madras Post Graduate Diploma in Social Service.
20. P.S.G.School of Social Works, Post Graduate Diploma in Social Work.
21. University of Madras i) A diploma in Social Service.
Ii) A master degree in Social Work.
22. Annamalal University M.A.Degree in Social Science.
23. National Institute of Social Sciences, Diploma course in social service
Bangalore Administration.
24.Karnataka University Master of Art in Sociology & Economics.
25. Udaipur School of Social work M.A.Degree
Rajasthan University.
26. Institute of Social Sciences, Agra Master of Social work.
University, Agra
27. Kashi Vidyapi-th, Varanasi (i) Master of Applied Sociology
(ii)A Diploma of the Labour Training Course
(iii)A Diploma of the Social Science Class.
28. J.K.Institute of Sociology and Human (I) M.A.in Social Work.
Relations, Lucknow, Lucknow (ii) A Diploma in social service.
University (iii) A diploma in social Technique or Social
Work.
(iv)A Degree of Master of Social
Technique,
29. Agra University M.A.in Sociology
30. University of Lucknow Master of Social Work.
31. All India Institute of Social Welfare Diplomas in Social Work
And Business Management,
Calcutta University.
32. Indian Institute of Technology Diploma in Industrial Psychology and
Kharagpur Relations.
33. Calcutta University A diploma in Social Service.
34. Edinburgh University Diploma in Social Study.
35. Royal College of Science and Certificate in Industrial Management
Technology, Glassgow.
36. University College of South Walves Diploma in Social Science.
And monithshire University Wales,
Cardiff.
37. Glassgow School of Management Certificate in Personnel Management
Studies.
38. Manchester Municipal College of Certificate in Personnel Management.
Technology, Manchester.
39. Manchester College of Industrial Certificate in Personnel Management
Administration, University of
Manchester.
40. Victoria University of Manchester. Diploma in Personnel Management
41. London School of Economics and Diploma in Personnel Administration
Political Science.
42. Manchester University U.K. Associate of Manchester College of
Science and Technology in Industrial
Administration.
43. Institute of Personnel Management Graduate Membership.
London.
44. University of Indore i) M.A. Degree in Sociology
ii) Master’s degree in Social work.
45. University of Nagpur Diploma in Social Work Labour
Welfare as a special subject.
46. Punjab University Chandigarh i) M.A. Degree in Sociology with
Industrial Sociology.
Ii) Diploma in Personnel Management
And Labour Welfare
Or
Master's degree in personnel
Management & Industrial Relations.
Iii) M.A. In Public Administration with
Specialization in Labour Welfare
Administration.
47. Punjabi University, Patiala i) Diploma Course in Labour Laws,
Labour Welfare and Personnel
Management, granted as a result of
Examination held prior to Dec 1978
Ii) Diploma in personnel Management and
Industrial Relations granted as a result
Of examination held in Dec 1978 and
Thereafter.
48. Institute of Social Service Mangalore M.A. Degree inf Social work with
specialization in group (a)
49. Institute of Management, Ahmedabad Degree of Master of Business
Administration.
50. Institute of Management, Calcutta Degree of Master of Business
Administration
51. Guru Nanak Dev University,Amritsar Diploma in Labour Laws and Labour
Administration.
52. Ranchi University, Ranchi M.A. Degree in Labour & Welfare
53. Bhartiya Vidya Bhawan, Rajendra Post Graduate Diploma Course in
Prasad Institute of Communication Industrial Relations and Personnel &
Management Bombay. Management
54. Indian Social Insitute Lodhi Road Post-Graduate Diploma in Social Service.
New Delhi.
55. Jamia Millia Iislamia, Jamia Nagar Post-Graduate course in Social Works
Delhi 110025
56. Himachal Pradesh University, Post-Graduate Diploma in Personnel
Shimla-5 Management and a Labour Welfare
57. Gorakhpur University, Gorakhpur Post-Graduate Diploma in Business
Management.
58. Punjab University, Chandigarh Advanced Deploma in Labour Laws.
59. D.A.V.College of Management Post-Graduate Diploma in Personnel
Communication to Educational Management and Industrial.
Administration D.A.V.School
Building Sector 8-CM Chandigarh
60. National Labour Institute, A.B.6 Post Graduate Diploma Course in
Safdarjung Enclave, New Delhi Industrial Relation to Personnel
110029 Management.
61. Vikram University, Ujjain Madhya Post Graduate Diploma in Personnel
Pradesh Management.
62. Kurukshetra University, M.A.in Social work.
Kurukshetra (Haryana)
63. Institute of Personnel Management i)Post Graduate Diploma course in
And Industrial Relation S.C.O.No. Industrial Relation and Labour Law
268 (2nd floor) Sector 35-D, of Granted as a result of Examinations,
Chandigarh held prior to Jul 1993.
ii) Post Graduate Diploma in Personnel
Management and Industrial Relation
Granted as a result of examination held
in July 1993 and onwards.
64. Punjabi University, Patiala Post Graduate Diploma in M.A. (Social)
Works)
65. National Institute of Personnel Post Graduate Diploma in Personnel
Management 45 Jhotwtala Road Management.
Calcutta.
6. Conditions of Service of Welfare Officers:-
(1) A Welfare Officer shall be given appropriate status corresponding to the status of
the other executive heads of the factory.
(2) The conditions of service of a Welfare Officer shall be the other members of the
staff of corresponding status in the fatory.
(3) Notwithstanding any thing contained in sub-rule (2) the management may impose
and one or more of the following punishment on a Welfare Officer.
(I) Censure;
(ii) Withholding of increments including stoppage at an efficiency bar ;
(iii) Reduction to the lower stage in a time scale;
(iv) Suspension; and
(v) Dismissal or termination of service in any other manner;
Provided that no order of punishment shall be passed against the Welfare Officer unless
he has been informed of the grounds on which it is proposed to take action and given a
reasonable opportunity of defending himself against the action proposed to be taken in regard to
him.
Provided further that the management shall not impose any punishment other than
censure except with the previous concurrence of the Labour Commissioner, Punjab.
4) The Labour Commissioner, Punjab before passing orders on a reference made
under second proviso to sub rule (3), shall give the Welfare Office and opportunity of
showing cause against the action proposed to be taken against him and if necessary, any
hear the parties in person.
5) If the Labour Commissioner, on a reference made to him under the second proviso
to sub-rule (3) refuses to give his concurrence, the management may appeal to the
State Government within thirty days from the date of the receipt of such refusal. The
decision of the State Government shall be final and binding
6) A Welfare Officer upon whim the punishment mentioned in clause (v0 of sub-rule
(3) is imposed may appeal to the State Government against the order of punishment
within thirty days from the date of receipt of the order by him. The decision of the State
Government shall be final and binding.
7) The State Government may pass such interim order as may be necessary pending
the decision of appeal filed under the sub-rule (5) of sub-rule (6)
7. Duties of Welfare Officer:-
(I) to establish contents and hold consultations with a vies the maintaining
harmonious relation between the factory management and workers:
(ii) to bring to the notice of the factory management the grievances of workers,
individual as well as collective, with a view to securing their expeditious redress and (to
act as Liaison Officer between the management and Labour)
(iii) to study and understand the point of view of Labour in order to help the factory
management to shape and formulate labour po9licies and to interpret these policies to
the workers in a language they can understand:
(iv) to watch industrial relations with a view to using his influence in the event of a
dispute arising between the factory management and workers and to help to bring
about settlements by pressure effects.
(v) Omitted
(vi) Omitted
(vii) Omitted.
(viii) (To advise on fulfillment by the concerned departments of the factory on)
Obligations, statutory or otherwise concerning the applications, of
provisions of the Act and the rules made thereunder, and to establish
Liaison with the factory inspector and the Medical Services concerning
medical examinations of employees, health records, supervision of
hazardous jobs sick visiting and convalescents accidents prevention and
supervision of hazardous jobs sick visiting and convalescents accidents
prevention and supervision of safety education, investigation of accidents,
maternity benefits and workman;s compensation.
(ix) (to promote relation between the concerned departments of the factory
and the workers which will bring about productive efficiency) as well as
amelioration in the working conditions and to help workers to adjust and
adopt themselves to their working environments;
(x) To encourage the formation of Works and Joint Production Committee Co-
operative Societies and Safety First and Welfare Committees, and to
supervise their work.
(xi) (to advise on provision of welfare facilities) such as canteen, shelters for rest,
creches, adequate latrine facilities, drinking water sickness and benevolent scheme,
payment, pension and superannuation funds, gratuity payments granting of loans and
legal advice to workers;
(xii) to help the factory management in regulating the grant of leave with
wages and explain to the workers the provision relating to leave with
wages and other leave privileges and to guide the workers in the matter of
submission of application for grant of leave for regulating authorized
absence;
(xiii) to secure welfare provisions, such as housing facilities, food-stuffs social and
recreational facilities sanitation advise on individual personal problems and education of
children;
(xv) To suggest measures which will serve to raise the standard of living of workers
and in general promote their well being.
(xvi) (To take adequate steps for eradication of illiteracy from amongst the workers
working in the factories and their families.
(7A Welfare Officer not to perform certain duties: - A Welfare Officer shall not perform any
other duties except those mentioned in rule 7 or hold any other office or post without the
previous sanction in writing of the Labour Commissioner or the State Government.
(7B Welfare Officer not to deal with disciplinary case and appear on behalf of the
management against workers:- Without prejudice the generality of rule 7A no welfare
officer shall deal with any disciplinary cases against workers or appear before a
Conciliation Officer, on in a Court or Tribunal on behalf of the factory management
against a worker or worker)
8. Power of exemption:-
The State Government may be notification in the official Gazette, exempt any factory or class or
description of factories from the operation of all or any of the provision of these Rules, Subject to
compliance with such alternative arrangement as may be
Punjab Control of Industrial Major Accident Hazards
( Amendment ) Rules, 2002
RULES
1. Short title and commencement-
i) These rules may be called the Punjab Control of Industrial Major
Accident Hazards ( Amendment ) Rules, 2002
ii) They shall come into force on and with effect from the date of their
publication in the official Gazette.
2. Definition- In these rules unless the context otherwise requires.
a) “Authority” means an authority or person appointed & designated by the
State Government as District Emergency Authority.
b) Omitted
c) "hazardous chemical" means-
(i) any chemical which satisfies any of the criteria laid down in Part I of
Schedule I and is listed in Column 2 of Part II of this Schedule; or
(ii) any chemical listed in Column 2 of Schedule 2;
(iii) any chemical listed in Column 2 of Schedule 3;
d) "industrial activity" means-
(i) an operation or process carried out in a factory referred to in
Schedule 4 involving or likely to involve one or more hazardous chemicals
and includes on-site storage or on-site transport which is associated with
that operation or process, as the case may be; or
(ii) isolated storage; or
(iii) a pipe line;
e) " isolated storage" means a storage where no manufacturing process other
than pumping of hazardous chemical is carried out and that storage involves
at least a quantity of that chemical set out in Schedule 2, but does not
include storage associated with in factory specified in Schedule 4 on the
same site.
f) "major accident" means an incident involving loss of life inside or outside
the site or ten or more injuries inside and / or one or more injuries outside or
release of toxic chemical or explosion or fire or spillage of hazardous
chemical resulting in ‘on-site’ or ‘off-site’ emergencies or damage to
equipments leading to stoppage of process or adverse effect to the
environment;
g) "pipeline" means a pipe (together with any apparatus and works associated
therewith), or system of pipes (together with any apparatus and works
associated therewith) for the conveyance of a hazardous chemical, other
than a flammable gas as set out in Column 2 of Part II of Schedule 3 at a
pressure of less than 8 bars absolute;
h) "Schedule" means Schedule appended to these rules;
i) "Site" means any location where hazardous chemicals are manufactured or
processed, stored, handled, used or disposed off and includes the whole of
an area under the control of an occupier ;
j) Words and expressions not defined in these rules but defined or used in the
Factories Act, 1948 and in any other rules made thereunder have the same
meaning, as assigned therein.
3. Collection, Development and Dissemination of Information. (1) This rule shall apply
to an industrial activity or isolated storage in which a hazardous chemical
which satisfies any of the criteria laid down in part I of Schedule I and is
listed in Column 2 of Part II of this Schedule is or may be involved.
(2) An occupier, of an industrial activity or isolated storage in
terms of sub-rule (1) of this rule, shall arrange to obtain or develop a
detailed information specified on hazardous chemicals in the form of
a material safety data sheet as indicated in Schedule 5 and the information
so obtained shall be accessible to workers upon request for reference
purpose.
(3) The occupier, while obtaining or developing a safety data sheet as
specified in sub-rule (2) shall ensure that the information is recorded
accurately and reflects the scientific evidence used in making the hazards
determination and in case, any significant information regarding hazard of a
chemical is available, it shall be added to the safety data sheet as specified
in Schedule 5 as soon as practicable.
(4) Every container of a hazardous chemical shall be clearly labelled or
marked to identify,-
(a) the contents of the container,
(b) the name and address of manufacturer or importer of the hazardous
chemical; and
(c) the physical, chemical and toxicological data of the hazardous chemical.
(5) In terms of sub-rule (4), where it is impracticable to label a
chemical in view of the size of the container or the nature of the package,
provision shall be made for other effective means like tagging or
accompanying documents.
3-A Duties of Inspector: - The Inspector shall;-
(a) Inspect the industrial activity or isolated storage at least once in a calendar
year;
(b) send annually status report on the compliance with the rules by occupiers
to the Ministry of Environment and Forests through the Directorate General
Factory Advice Service and Labour Institutes and Ministry of Labour,
Government of India;
( c) enforce direction and procedures in respect of industrial activities or
isolated storage covered under Factories Act, 1948 and in respect of
pipelines up to a distance of 500 meters from the outside of perimeter of
the factory, regarding-
(i) Notification of major accidents as per sub rule (1) and (2) of rule 5;
(ii) Notification of sites as per rules 7 and 8;
(iii) Safety Reports and Safety Audits as per rules 10 to 12; and
(iv) Preparation of on-site emergency plans as per rule 13 and
involvement in preparation of off-site plans in consultation with District
Collector or District Emergency Authority.
4. General responsibility of the occupier;-(1) This rule shall apply to,-
(a) an industrial activity, in which a hazardous chemical, is or may be
involved; and
(b) isolated storage in which a threshold quantity of a hazardous
chemical listed in Column 2 of schedule 2 which is equal to or more
than the threshold quantity specified for that chemical in Column 3 of
the said schedule , is involved.
(2) An occupier in term of Sub-rule (I) shall provide information on
demand to show that he has,-
(a) identified the major accident hazards; and
(b) taken adequate steps to –
(i) prevent such major accidents and o limit their consequences to
persons and the environment; and
(ii) provide to the persons working on the site with the information,
training and equipment including antidotes necessary to ensure
their safely and health.
5. Notification of Major accidents.;-(1) Where a major accident occurs on a site, the
occupier shall forthwith notify the Inspector and the Chief Inspector
of the accident, and furnish thereafter to the Inspector and Chief
Inspector a report relating to the accident in instalments, if
necessary, in the form specified in Schedule 6.
(2) The Inspector and the Chief Inspector shall, on receipt of the report in
accordance with sub-rule(1) of this rule, undertake a full
analysis of the major accident and send the requisite information to
the Ministry of Environment and Forests through the Directorate
General Factory Advice Service and Labour Institutes and Ministry of
Labour, Government of India..
(3) An occupier shall notify to the Inspector the steps taken to avoid any
repetition of such occurrence on a site.
(4) The Inspector and the Chief Inspector shall compile information
regarding the major accidents and make available copy of the same
to the Ministry of Environment and Forests through the Directorate
General Factory Advice Service and Labour Institutes and Ministry
of Labour, Government of India,
(5) The Inspector and the Chief Inspector shall inform the occupier in
writing of any lacunae, which in their opinion needs to be rectified to
avoid major accidents.
6. Industrial activities or isolated storage to which rules 7,8,10 to 13 and 15 shall apply:-
(a) the provisions of rules 7,8,13 and 15 shall apply to an
industrial activity, other than isolated storage in which there is
chemical listed in column 2 of Schedule 3, which is equal to or more
than the threshold quantity specified in the entry for that chemical in
column 3;.
(b) the provisions of rules 10,11 and 12 shall apply to an industrial
activity, other than isolated storage, in which there is involved a
quantity of a hazardous chemical listed in Column 2 of Schedule 3
which is equal to or more than the threshold quantity specified for
that chemical in Column 4 of said Schedule;
(c) the provisions of rules 7and 8 shall apply to an isolated storage in
which there is involved a quantity of a hazardous chemical listed in
Column 2 of Schedule 3 which is equal to or more than the
threshold quantity specified for that chemical in Column 3 of said
Schedule; and
(d) the provisions of rules 10,11,12,13 and15 shall apply to an isolated
storage in which there is involved a quantity of a hazardous chemical
listed in Column 2 of Schedule 2 which is equal to or more than the
threshold quantity specified for that chemical in Column 4 of the said
Schedule.
2) sub rule (2) shall be omitted.
7. Notification of site – (1) An occupier shall not undertake any site or isolated
storage unless he has submitted a written report to the Chief
Inspector containing the particulars specified in Schedule 7 at least
ninety days before commencing that activity or before such shorter
time, as the Chief Inspector may agree and for the purpose of this
rule, an activity in which subsequently there is or is likely to be a
threshold quantity specified in column 3 of Schedule 2 and 3 or more
of an additional hazardous chemical shall be a deemed to be a
different industrial activity and shall be notified accordingly.
(2) The Chief Inspector within sixty days from the date of receipt of the
report in accordance with this sub-rule(1) shall examine and on
examination of the report if he is of the opinion that contravention of
the provisions of the Act or the rules made thereunder has taken
place, he may issue notice for obtaining compliance.
8 Updating of the site notification :- Where an activity has been reported in
accordance with sub-rule (1) of rule 7 and the occupier makes a
change in it (including an increase or decrease in the maximum
quantity of a hazardous chemical to which this rule applies which is
or is liable to be at the site or in the pipeline or at the cessation of the
activity) which effects the particulars specified in that report or any
subsequent report made under this rule, the occupier shall forthwith
furnish a further report to the Inspector and the Chief Inspector.
9 In the said rule 9 shall be omitted.
10 Safety Reports and Safety Audit Reports. (1) Subjects to the provisions of
sub-rules (2) and (3), an occupier shall not undertake any industrial
activity or isolated storage to which this rule applies, unless he has
prepared a safely report on that industrial activity or isolated storage
containing the information specified in Schedule 8 and has sent a
copy of that report to the Chief Inspector at least ninety days before
commencing that activity.
(2) After commencement of these rules, the occupiers of both the new
and existing industrial activities or isolated storage shall arrange to
carry out safety audit by competent agency to be accredited by an
accreditation board to be constituted by the Ministry of Labour,
Government of India in this behalf. Further such auditing shall be
carried out as under:-
(a) internally once in a year by a team of suitable plant personnel
(b) externally once in two years by a competent agency accredited in this
behalf; and
(c) in the year when external audit is carried out, internal audit need not
be carried out.
(3) The occupier within thirty days of the completion of the audit, shall
send a report to the Chief Inspector with respect to the
implementation of recommendations.
11 Updating of safety reports under rule 10;- (1) Where an occupier has made a safety
report in accordance with sub-rule (I) of rule 10, he shall
not make any modification to The industrial activity or
isolated storage to which that safely report relates which could
materially affect the particulars in that report, unless the has made a
further report to take account of those modifications and has
sent a copy of that report to the Inspector and the Chief Inspector at
least ninety days before making those modifications.
(2) Where an occupier has made a report in accordance with sub-rule (1)
and rule 10 and that industrial activity or isolated storage is
continuing the occupier shall within a period of three years from the
date of the last such report make a further report which shall regard
in particular to new technical knowledge which has affected the
particulars in the previous report relating to safely and hazard
assessment, and shall within a period of thirty days or in such longer
time, as the Chief Inspector may agree in writing, send a copy of the
report to the Inspector and the Chief Inspector.
12 Requirement for further information to be sent to Inspector and the Chief
Inspector;- (1) Where in accordance with rule 10 and 11, an occupier has
sent a safety report and safety report relating to an industrial activity
or isolated storage to the Inspector and the Chief Inspector, the
Inspector and the Chief Inspector may, by a notice served on the
occupier, require him to provide such additional information as is
specified in the notice and the occupier shall send that information to
the Inspector and the Chief Inspector within ninety days.
13 Preparation of on-site emergency plan by the occupier;- (1) The occupier
shall prepare , keep up-to-date and furnish to the Inspector and Chief
Inspector, an on-site emergency plan containing details specified
in Schedule 8-A and detailing how major accidents will be dealt with on the
site on which the industrial activity or isolated storage is carried on and that
plan shall include the name of The person who is responsible for safety on
the site and the names of those who are authorised to take action in
accordance with the plan in case of an emergency
(2) The occupier shall ensure that the emergency plan prepared in
accordance with sub-rule (1), takes into account any modification made in
the industrial activity or isolated storage and that every person on the site
who is concerned with the plan-is informed of its relevant provisions.
(3) The occupier shall prepare the emergency plan required under sub-rule (1);
(a) before the commencement of industrial activity or isolated storage;
and
(b) with in ninety days of coming into operation of these rules in case of
an existing industrial activity or isolated storage.
(4) the occupier shall ensure that mock drill of the on-site emergency is
conducted at least once every six months.
(5) A detailed report of mock drill conducted under sub-rule(4) shall be
made immediately available to the Inspector and the Chief
Inspector.
14. Preparation of off-site emergency plan by the authority; Omitted
15 Information to be given to persons liable to be affected by a major accidents;
(1) The occupier shall take appropriate steps to inform persons outside
the site who are likely to be in an area which may be affected by a
major accident about,-
(a) the nature of the major hazards; and
(b) the safety measures and the "Do’s’ and ‘Don’ts" which should be
adopted in the event of a major accident
(2) The occupier shall take the steps required under sub-rule (i) to inform
persons about an industrial activity or isolated storage before that
activity is commenced, except that in the respect of an existing
industrial activity or isolated storage , the occupier shall comply with
the requirements of sub- rule (I) within ninety days of coming into
operation of these rules.
16 Disclosure of information; Where for the purpose of evaluating information
notified under rule 5 or 7,8,10 to13 and 15, the Inspector and the
Chief Inspector discloses that information to some other person that
other person shall not use that information for any purpose except for
the purpose of the Inspector or the Chief Inspector disclosing it as
the case may be, and before disclosing that information the Inspector
or the Chief Inspector, as the case may be, shall inform that other
person of his obligations under this rule.
17 Improvement Notice ;- Omitted
SCHEDULE I
[See rule 2(c)(i), 4(1)(a), 4(2), 17 and 18]
Indicative Criteria and List of Chemicals
PART I
(a) Toxic Chemicals:
Chemicals having the following values of acute toxicity and which, owing to their physical
and chemical properties, are capable of producing major accidents hazards.
S.No. Degree of
Toxicity
Medium lethal dose
by the oral route
(oral toxicity) LD50
(mg/kg) body weight
of test animals
Medium lethal dose by
the dermal route
(dermal toxicity) LD 50
(mg/kg) body weight of
test animals
Medium lethal
concentration by
inhalation route (four
hours) LC 50 (mg/l)
inhalation on test
animals
1 Extremely
toxic
1 - 50 1 - 200 0.1 - 0.5
2 Highly
toxic
51 - 500 201 - 2000 0.5 - 2.0
(b) Flammable chemicals:
(i) Flammable gases; chemicals which in the gaseous state at normal pressure
and mixed with air become flammable and the boiling point of which at normal
pressure is 20°C or below;
(ii) highly flammable liquids: chemicals which have a flash point lower than
23°C and the boiling point of which at normal pressure is above 20° C;
(iii) flammable liquids: chemicals which have a flash point lower than 65°C- and
which remain liquids under pressure, where particular processing conditions, such
as high pressure and high temperature, may create major accident hazards.
(c) Explosives:
Chemicals which may explode under the effect of flame, heat or photo-chemical
conditions or which are more sensitive to shocks or friction than dinitrobenzene.
PART II
LIST OF HAZARDOUS AND TOXIC CHEMICALS
Sl.
No.
Name of the Chemical
1 Acetone
2 Acetone Cynohydride
3 Acetyle Chloride
4 Acetylene (Ethyne)
5 Acrolein (2-Propenal)
6 Acrylonitrile
7 Aldicarb
8 Aldrin
9 Alkyl Phthalate
10 Allyl Alcohol
11 Allylamine
12 Alpha Naphthyl Thiourea (Antu)
13 Aminodiphenyl-4
14 Aminophenol-2
15 Amiton
16 Ammonia
17 Ammonium Nitrate
18 Ammonium Nitrates in fertilizers
19 Ammonium Sulfamate
20 Anabasine
21 Aniline
22 Anisidine-p
23 Antimony and Compounds
24 Antimony Hydride (Stibine)
25 Arsenic Hydride (Arsine)
26 Arsenic Pentoxide, Arsenic (v) Acid, and Salts
27 Arsenic Trioxide, Alsenious (iii) Acids and Salts
28 Asbestos
29 azinophos-Ethyl
30 Azinphos-Methyl
31 Banum Azide
32 Benzene
33 Benzidine
34 Benzidine Salts
35 Benzoquinone
36 Benzoyl Chloride
37 Benzoyl Peroxide
38 Benzyl Chloride
39 Benzyl Cynide
40 Beryllium (Powders Compound)
41 Biphenyl
42 Bis ( 2-Clzloromethyl ) Ketone
43 Bis (2, 4, 6-Trinitrophynile) Amine
44 Bis (2, Chloroethyle sulphide)
45 Bis (Chloromethyl) ether
46 Bis (tert-Butyl peroxy) Butane-2, 2
47 Bis (tert-Butyl peroxy) Cyclohexane-11
48 Bis-1, 2 Tribromophenoxy Ethane
49 Bis phenol
50 Boron and Compounds
51 Bromine
52 Bromine Pentafluoride
53 Bromoform
54 Butoadine
55 Butane
56 Butanethiol
57 Butanone-2
58 Butoxy Ethanol
59 Butyl Glycidal Ether
60 Butyl Peroxy acetate, tert
61 BUtyL Peroxyisobutyrate, tert
62 Butyl Peroxyisopropyl Carbonate, tert
63 Butyl Peroxymaleate, tert
64 Butyl Peroxypivalate, tcrt
65 Butyl Vinyl Ether
66 Buty-n-Mercaptan
67 Butylamine
68 C-9, Aromatic Hydrocarbon Fraction
69 Cadmium and Compounds
70 Cadmium Oxide (fumes)
71 Calcium Cynicde
72 Captan
73 Captofol
74 Carbaryl (Sevin)
75 Carbofuran
76 Carbon Disulphide
77 Carbon Monoxide
78 Carbon Tetrachloride
79 Carbophenothion
80 Cellulose Nitrate
81 Chlorats (used in explosives)
82 Chlordane
83 Chlorfenvinphos
84 Chlorinated Benzenes
85 Chlorine
86 Chlorine Di Oxide
87 Chlorine Oxide
88 Chlorine Trifluoride
89 Chloromequal Chloride
90 Chloroacetalchloride
91 Chloroacetaldehyde
92 Chloroanilin-2
93 Chloroaniline4
94 Chlorobenzene
95 Chlorodiphenyl
96 Chloropoxypropane
97 Chloroethanol
98 Chloroethyl
99 Chloroformate
100 Chorolfluorocarbons
101 Chloroform
102 Chloroformyl-4, Merpholine
103 Chloromethane
104 Chloromethyl Ether
105 Chloromethyl Methyl Ether
106 Chloronitrobenzene
107 Chloroprene
108 Chlorosulphonic Acid
109 Chlorotrinitro benzene
110 Chloroxuron
111 Chromium and Compounds
112 Cobalt and Compounds
113 Copper and Compounds
114 Coumafuryl
115 Coumaphos
116 Coumateralyl
117 Cresols
118 Cumidine
119 Cumene
120 Cynophos
121 Cynothoate
122 Cyanuric Fluoride
123 Cyclohexane
124 Cyclohexanol
125 Cyclohexane
126 Cycloheximide
127 Cyclopentadinene
128 Cyclopentane
129 Cyclotetramethylenetrinitramine
130 Cyclotriethylene Trinitramine
131 DDT
132 Dicarbomodiphenyl Oxide
133 Demeton
134 Di-Isobutyl Peroxide
135 Di n-Propyl Peroxydicarbonate
136 Di-sec-Butyl Peroxydicarbonate
137 Dalifos Mazodinitrophewl
138 Diszomethane
139 Dibenzyl Peroxydicarbonate
140 Diehloroaeetylene
141 Diehlorobenzene-0
142 Dichlorobenzene-2
143 Di-chloroethane
144 Dichlorethyl Ether
145 Dichlorophenol-2, 4
146 Dichlorophenol-2, 6
147 Dichlorophenoxy Acetic Acid, -2,4 (2,4-D)
148 Dichloropropane-1, 2
149 Diehlorosalicylic Acid, -3,5
150 Dichlorovos (DDVP)
151 Dicrotophos
152 Dieldrin
153 Diepoxybutane
154 Diethyl Peroxydicarbonate
155 Diethyl Glycol Dinitrate
156 Diethylene Triarnine
157 Diehyleneglycol Butyl Ether/Diethyleteglycol Butyl Acetate
158 Diethylenetriarnine (DETA)
159 Diglycidyl Ether
160 Dihydroperoxypropane, -2,2
161 Diisobutyryl Peroxide
162 Dimethoate
163 Dimethyl Phosphoramidocynidic Acid
164 Dimelhyl Phthalate
165 Dimethylcarbonyl
166 Dimethylnitrosamine
167 Dinitrophenol, Salts
168 Dinitroluene
169 Dinitro-o-Cresol
170 Dioxane
171 Dioxathion
172 Dioxalane
173 Diphacinone
174 Diphosphoramide Octamethyl
175 Dipropylene Glycolmethylether
176 Disulfoton
177 Endosulfan
178 Endrin
179 Epiehlorohydrine
180 EPN
181 Epoxypropane, 1, 2
182 Ehion
183 Ethyl Carbarnate f
184 Ethyl ether
185 Ethyl Hexanol, -2
186 Ethyl Mercaptan
187 Ethyl Methacrylate
188 Ethyl Nitrate
189 Ethylamine
190 Ethylene
191 Ethylene Chlorohydrine
192 Ethylene Diamine
193 Ethylene Dibromide
194 Ethylene Dichloride
195 Ethylene Glycol Dinitrate
196 Ethylene Oxide
197 Ethyleneimine
198 Ethylthiocynate
199 Fensulphothion
200 Fluenetil
201 Fluoro, -4,2-Hydroxybutyric Acid and Salts, Esters, Amides
202 Fluoroacetic Acid and Salts, Esters, Amides
203 Fluorobutyric Acid, -4, and Salts, Esters, Amides
204 Fluorocrotonic Acid, -4, and Salts, Esters, Amides
205 Formaldehyde
206 Glyconitrite (Hydroxyacetonitrite)
207 Guanyl, -1, 4 Nitrosaminoguanyl-1-Tetrazenc
208 Heptachlor
209 Haxachloro Cyclopentadiene
210 Hexachlorocyclohexane
211 Hexachlorocy cloamethane
212 Hexachlorodibenzo-p-Dioxin, -1, 2, 3, 7, 8, 9
213 Hexafluoropropene
214 Hexamethylphosphoramide
215 Hexamethyl, -3, 3, 6, 6, 9, 9, -1, 2, 4, 5-Tetroxacyclononane
216 Hexamethylenediamine
217 Hexane
218 Hexanitrosstibene, -2, 2, 4, 4, 6, 6,
219 Hexavalent Chromium
220 Hydrazine
221 Hyrazine Nitrate Hydrochloric Acid
222 Hydrogen
223 Hydrogen Bromide (Hydrobromic Acid)
224 Hydrogen Chloride (Liquified Gas)
225 Hydrogen Cynide
226 Hydrogen Fluoride
227 Hydrogen Selenide
228 Hydrogen Sulphide
229 Hydroquinone
230 Iodine
231 Isobenzan
232 Isodrin
233 Isophorone Diisocynate
234 Isopropyl Ether
235 Juglone (5-Hydroxynaphthalene-1, 4-Dione)
236 Lead (inorganic fumes & dusts)
237 Lead 2, 4, 6 -Trinitroresorcinoxide (Lead Styphnate)
238 Lead Azide
239 Leptophos
240 Lindane
241 Liquified Petroleum Gas (LPG)
242 Maleic Anhydride
243 Manganese & Compounds
244 Mercapto Benzothiawle
245 Mercury Alkyl
246 Mercury Fulminate
247 Mercury Methyl
248 Methacrylic Anhydride
249 Methacrylonitrite
250 Methacryloyl Chloride
251 Methamidophos
252 Methanesuphonyl Fluoride
253 Methanethiol
254 Methoxy Ethanol (2-Methyl Cellosive)
255 Methoxy ethyl mercuric Acetate
256 Methyl Acrylate
257 Melhyl Alcohol
258 Methyl Amylketone
259 Methyl Bromide (Bromomethane)
260 Methyl Chloride
261 Methyl Chloroform
262 Methyl Cyclohexene
263 Methyl Ethyl Ketone Peroxide
264 Methyl Hydrazine
265 Methyl Isobutyl Ketone
266 Methy Isobutyl Ketone Peroxide
267 Mthyl Isocycnate
268 Methyl Isothiocynate
269 Methyl Mercaptian
270 Methyl Methacrylate
271 Methyl Parathion
272 Methyl Phosphonic Dichloride
273 Methyl-N, 2, 4, 6,-Trinitroaniline
274 Methylene Chloride
275 Methylenebis, -4, 4, (2-Chloroaniline)
276 Methyltrichlcrosilane
277 Mevinphos
278 Molybdenum & Compounds
279 N-Methyl-N, 2, 4, 6-N-Tetranitroanilin
280 Naptha (Coal Tar)
281 Naphthylamine, 2
282 Nickel & Compounds
283 Nickel Tetracarbonyl
284 Noitroaniline-O
285 Nitroaniline-P
286 Nitrobenzene
287 Nitrochloroberizene-P
288 Nitrocyclohexane
289 Nitriothage
290 Nitrogen.Dioxide
291 Nitrogen Oxide
292 Nitrogen Trifluoride
293 Nitroglycerine
294 Nitrophenol-P
295 Nitropropane-1
296 Nitropropane-2
297 Nitrosodirnethylarnine
298 Nitrotolune
299 Octabrornophenyl Oxide
300 Oleurn
301 Oleylarnine
302 OO-Diethyl S-EthyIsulphonyImethyl phosbhorothioate
303 OO-Diethyl S-Ethylthiornethyl Phosphorothioate
304 OO-Diethyl S-Ethiomethyl'Phosphorathioate
305 OO-Diethyl S-1sopropyliniornethyl Phosphorolithioate
306 OO-diethyl S-Propylthiornethyl Phosphorodithioate
307 Oxyarnyl
308 Oxydisulioton
309 Oxygen (Liquid)
310 Oxygen Difluoride
311 Ozone
312 Paraoxon (Diethyl 4-Nitrophenyl Phosphate)
313 Paraquat
314 Parathion
315 Parathion Methyl
316 Paris green (Bis Aceto Hexametaatsinito Tetracopper)
317 Pentaborane
318 Pentabromodiphenyl Oxide
319 Pentabromophenol
320 Pentachloro Naphthalene
321 Pentachloroethane
322 Petachlorophenol
323 Pentacrythritol Tetranitrate
324 Pentane
325 Peracetic Acid
326 Perchloroethylene
327 Perchlorornethyl Mercaptan
328 Pentanone, 2,4-Methyl
329 Phenol
330 Phenyl Glycidal Ether
331 Phenylene p-Diarnine
332 Phenylmercury Acetate
333 Phorate
334 Phosacetim
335 Phosalone
336 Phosfolan
337 Phosgene (Carbonyl Chloride)
338 Phosmet
339 Phospamidon
340 Phosphine (Hydrogen Phosphide)
341 Phosphoric Acid and Esters
342 Phosphoric Acid, Bromethyl Bromo (2,2-dimethylpropyl)
Bromoethyl Ester
343 Phosphoric Acid, Bromoethyl Bromo (2,2-Dimethylpropyl)
Chlorethyethyl Ester
344 Phosphoric Acid, Chlorocthyl Bromo (2,2-Dimethoxylpropyl)
Chloroethyl Ester
345 Phosporous & Compounds
346 Phostalan Pircic Acid (2,4,6-Trinitrophenol)
347 Polybrominaled Biphenyl
348 Potassium Arsenite
349 Potassium Chlorate
350 Promurit (1-(3, 4-Dichlorophenyl)-3-
Triazenethiocarboxamide)
351 Propanesultone-1, 3
352 Propen,-1, 2-Chloro-1,3-Diol-Diacetate
353 Propylene Dichloride
354 Propylene Oxide
355 Propyleneimine
356 Pyrazoxon
357 Selenium Hexafluoride
358 Semicarbazide Hydrochloride
359 Sodium Arsenite
360 Sodium Azide
361 Sodium Chlorate
362 Sodium Cynide
363 Sodium Picramate
364 Sodium Selenite
365 Styrene, 1, 1, 2, 2-Tetrachloroethane
366 Sulfotep
367 Sulphur Dichloride
368 Sulphur Dioxide
369 Sulphur Trioxide
370 Sulphuric Acid
371 Sulphoxide, 3-Chloropropyloctyl
372 Tellurium
373 Tellurium Hexafluoride
374 Tepp
375 Terbufos
376 Tetrabromobisphenol-A
377 Tetrachloro, 2, 2, 5, 6, 2, 5-Cyclohexadiene-1, 4-Dione
378 Tetrachlorodibenzo-p Dioxin, 2, 3, 7, 8 (TCDD)
379 Tetraethyl Lead
380 Tetrafluoroethane
381 Tetramethylenedisulphotetramine
382 Tetramethyl Lead
383 Tetramnitromethane
384 Thalium & Compounds
385 Thionzin
386 Thionyl Chloride
387 Tirpate
388 Toluene
389 Toluidien-2, 4 Diisocynate
390 Toluidiene-O
391 Toluene 2, 6-Diisocynate
392 Trans-1, 4-Chlorobutene
393 Tri, -1 (Cyclohexyl) Stannyl-1H, 1, 2, 4-Trazole
394 Triamino, -1, 3, 5, 2, 4, 6-Trinitrobenzene
395 Tribromophenol, 2, 4, 6
396 Trichloro Acetyl Chloride
397 Trichloro Ethane
398 Trichloro Naphthalene
399 Ttichloro (chloromethyl) Silane
400 Trichlorodichlorophenylsilane
401 Triochloroethane, l, l, l
402 Trichloroethyl Silane
403 Trichloroethylene
404 Trichloromethanesulphenyl Chloride
405 Trichlorophenol, 2, 2, 6
406 Trichlorophenol, 2, 4, 5
407 Triethylamine
408 Triethylenemelamine
409 Trimethyl Chlorosilane
410 Trimethylopropane Phosphite
411 Trinitroaniline
412 Trinitroanisole, 2, 2, 4, 6
413 Trinolrobenzene
414 Trinitrobenzoic Acid
415 Trinitrocresol
416 Trinitrophenetole, 2, 4, 6
417 Trinitroesorcinol, 2, 4, 6 (Styphnic Acid)
418 Trinitrotoluene
419 Triorthocressyl Phosphate
420 Triphenylin Chloride
421 Turpenline Uranium & Compounds
422 Vanadium & Compounds
423 Vinyl Chloride
424 Vinyl Fluoride
425 Warfarin
426 Xylene
427 Xylidine
428 Zinc & Compounds
429 Zirconium & Compounds
SCHEDULE 2
[(See rule 2(e)(ii), 4(1)(b), 4(2) (1) and 6(1)(b)]
Isolated storage at Installations other than those covered by Schedule 4
(a) The threshold quantities set out below relate to each installation or group of
installations belonging to the same occupier where the distance between
installation is not sufficient to avoid, in foreseeable circumstances, any
aggravation of major accident hazards. These threshold quantities apply in
any case to each group of installations belonging to the same occupier
where the distance between the installations is less than 500 metres.
(b) For the purpose of determining the threshold quantity of hazardous
chemical at an isolated storage, account shall also be taken of any
hazardous chemical which is:-
(i) in that part of any pipeline under the control of the occupier having control of
the site wh.ch is within 500 metres of that site and connected to it;
(ii) at any other site under the control of the same occupier any part of the
boundary of which is within 500 metres of the said site; and
(iii) in any vehicle, vessel, aircraft or hovercraft, under the control of the same
occupier which is used for storage purpose either at the site or within 500
metres of it;
but no account shall be taken of any hazardous chemical which is in a
vehicle, vessel, aircraft or a hovercraft used for transporting it.
Threshold Quantities (tonnes)Sl.
No.
Chemicals
For application of
Rules 4, 5 and 7-9
For application of
Rules 10 to 15
1 2 3 4
1 Acrylonitrile 350 5,000
2 Ammonia 60 600
3 Ammonium nitrate (a) 350 2,500
4 Ammonium nitrate fertilizers (b) 1,250 10,000
5 Chlorine 10 25
6 Flammable gases as defined in
Schedule 1, paragraph (b) (i)
50 300
7 Highly flammable liquids as defined in
Schedule 1, paragraph (b) (ii)
10,000 100,000
8 Liquid oxygen 200 2,000
9 Sodium chlorate 25 250
10 Sulphur dioxide 20 500
11 Sulphur trioxide 15 100
12 Carbonyl Chloride 0.750 0.750
13 Hydrogen Sulphide 5 50
14 Hydrogen Fluoride 5 50
15 Hydrogen Cynide 5 50
16 Carbon Disulphide 5 50
17 Uromine 50 500
18 Ethylene Oxide 5 501
19 Propylene Oxide 5 50
20 Z-Propenel(acrolein) 20 200
21 Bromo methane(Methyl Bromide) 20 200
22 Methyl isocynate 0.150 0.150
23 Tetra Ethyl Lead or Tetra methyl Lead 5 50
24 1-2, Dibromomethane(Ethylene di
bromide)
5 50
25 Hydrogen Chloride 25 250
26 Diphenyl Methane Di-Isocynate (MDI) 20 200
27 Toluene Di-Isocynate (TDI) 10 100
(a) This applies to ammonium nitrate and mixtures of ammonium nitrates where
the nitrogen content derived from the ammonium nitrate is grater than 28
per cent by weight and to aqueous solutions of ammonium nitrate where
the concentration of ammonium nitrate is greater then 90 per cent by
weight
(b) This applies to straight ammonium nitrate fertilizers and to compound
fertilizers where the nitrogen content derived from the ammonium nitrate is
greater than 28 per cent by weight (a compound-fertilizer contains
ammonium nitrate together with phosphate and/or potash).
SCHEDULE 3
[See rule 2(e) (iii), 5 and 6(1) (a)]
List of Hazardous Chemicals for Application of Rules 5 and 7 to 15
(a) The quantities set-out-below relate to each installation or group of
installations belonging to the same occupier where the distance between
the installations is not sufficient to avoid, in foreseeable circumstances,
any aggravation of major-accident hazards. These quantities apply in
any case to each group of installations belonging to the same occupier
where the distance between the installations is less than 500 metres.
(b) For the purpose of determining the threshold quantity of a hazardous
chemical in an industrial installation, account shall also be taken of any
hazardous chemicals which is:-
(i) in that part of any pipeline under the control of the occupier have control of
the site, which is within 500 metres off that site and connected to it;
(ii) at any other site under the control of the same occupier any part of the
boundary of which is within 500 metres of the said site; and
(iii) in any vehicle, vessel, aircraft or hovercraft under the control of the same
occupier which is used for storage purpose either at the site or within
500 metres of it;
but no account shall be taken of any hazardous chemical which is in a vehicle,
vessel, aircraft or hovercraft used for transporting it.
PART I
Named Chemicals
S.No. Chemical Threshold Quantity CAS
Number
for application
of Rules, 5, 7-9
and 13-15
for application
of Rules 10-12
1 2 3 4 5
GROUP 1-TOXIC SUBSTANCES
1 Aldicarb 100 kg 116-06-3
2 4-Aminodiphenyl 1 kg 96-67-1
3 Amiton 1 kg 78-53-5
4 Anabasine 100 kg 494-52-0
5 Arseinc pentoxide, Arsenic (V) acid &
salts
500 kg
6 Arsenic trioxide, Arseius (III) acid &
salts
100 kg
7 Arsine (Arsenic hydride) 10 kg 7784-42-1
8 Azinphos-ethyl 100 kg 2642-71-9
9 Azinphos-melhyl 100 kg 86-50-0
10 Benzidine 1 kg 92-87-5
11 Benzidine salts 1 kg
12 Beryllium (powders, compounds} 10 kg
13 Bis (2-chloroethyl) sulphide 1 kg 505-60-2
14 Bis (chloromethyl) ether 1 kg 542-88-1
15 Carbophuran 100 kg 1563-66-2
16 Carbophenothion 100 kg 786-19-6
17 Chlorefenvinphos 100 kg 470-90-6
18 4-(Chloroformyl) morpholine 1 kg 15159-40-7
19 Chloromethyl methyl ether 1 kg 107-30-2
20 Cobalt (metal, oxides, carbonates,
sulphides, as powders)
1 t
21 Crimidine 100 kg 535-89-7
22 Cynthoate 100 kg 3734-95-0
23 Cycloheximide 100 kg 66-81-9
24 Demeton 100 kg 8065-48-3
25 Dialifos 100 kg 10311-84-9
26 OO-Diethyl S-ethylsulphinylmethyl
phosphorothiate
100 kg 2588-05-8
27 OO-Diethyl S-ethylsulphonylmethyl
phosphorothioate
100 kg 2588-06-9
28 OO-Dielhyl S-ethyllhiomethyl
Phosphorothioate
100 kg 2600-69-3
29 OO-Diethyl S-isopropylthiomethyl
phosphorodithioate
100 kg 78-52-4
30 OO-Diethyl S-propylthiomethyl
phosphorodithioate
100 kg 3309-68-0
31 Dimefox 100 kg 115-26-4
32 Dimethylcarbamoyl chloride 1 kg 79-44-7
33 Dimethylnitrosamine 1 kg 62-75-9
34 Dimethyl phosphoramidocynicidic
acid
1 t 63917-41-9
35 Diphacinone 100 kg 82-66-6
36 Disulfoton 100 kg 298-04-4
37 EPN 100 kg 2104-64-5
38 Ethion 100 kg 563-12-2
39 Fensulfothion 100 kg 115-90-2
40 Fluenetil 100 kg 4301-50-2
41 Fluroacetic acid 1 kg 144-49-0
42 Fluoroacetic acid, salts 1 kg
43 Fluoroacelic acid, esters 1 kg
44 Fluoroacetic acid, amides 1 kg
45 4-Fluorobutyric acid 1 kg 462-23-7
46 4-FIuorobutyric acid, salts 1 kg
47 4-Fluorobutyric acid, esters 1 kg
48 4-Fluorobutyric acid, amides 1 kg
49 4-Florocrotonic acid 1 kg 37759-72-1
50 4-Fluorocrotonic acid, salts 1 kg
51 4-Fluorocrotonic acid, esters 1 kg
52 4-Fluorocrotonic acid, amides 1 kg
53 4-Fluoro-2-hydroxybutyric acid,
amides
1 kg
54 4-Fluoro-2-hydroxybutyric acid, salts 1 kg
55 4-Fluoro-2-hydroxybutyric acid,
esters
1 kg
56 4-Fluoro-2-hydroxybutyric acid,
amides
1 kg
57 Glycolonitrile (Hydroxyacetonitrile) 100 kg 107-16-4
58 1, 2, 3, 7, 8, 9-Hexachlorodibenzo-p-
dioxin
100 g 194-8-74-3
59 Hexamethylphosphoramide 1 kg 680-31-9
60 Hydrogen sclenide 10 kg 7783-07-5
61 Isobenzan 100 kg 297-78-9
62 Isodrin 100 kg 465-73-6
63 Juglone (5-Hydroxynaphithalene 1, 4
dione)
100 kg 481-39-0
64 4, 4-Methylenebis (2-chloroniline) 10 kg 101-14-4
65 Methyl isocynate 150 kg 150 kg 624-83-9
66 Mevinphos 100 kg 7786-34-7
67 2-Naphlhylamine 1 kg 91 -59-8
68 2-Nickcl (metal, oxides, carbonates,
sulphides, as powders)
1 t
69 Nickel tetracarbonyl 10 kg 13463-39-3
70 Oxygendisulfoton 100 kg 2497-07-6
71 Oxygen difuoride 10 kg 7783-41-7
72 Paraxon (Diethyl 4-nitsphenyl
phosphate)
100 kg 311 -45-5
73 Parathion 100 kg 56-38-2
74 Parathion-methyl 100 kg 298-00-0
75 Pentaborane 100 kg 19624-22-7
76 Phorate 100 kg 298-02-2
77 Phosacetim 100 kg 4104-14-7
78 Phosgene (carbonyl chloride) 750 kg 750 kg 75-44-5
79 Phosphamidon 100 kg 13171-41-6
80 Posphine (Hydrogen phosphide) 100 kg 7803-51 -2
81 Promurit (1-(3, 4-dichlorophenyl)-3
triazenethiocarboxamide)
100 kg 5836-73-7
82 1, 3-Propanesultone 1 kg 1120-7t-4
83 1 -Propen-2-chloro- 1, 3-diol
diacetate
10 kg 10118-72-6
84 Pyrazoxon 100 kg 108-34-9
85 Selenium hexafluoride 10 kg 7783-79-1
86 Sodium selenite 100 kg 10102-18-8
87 Stibine (Antimony hydride) 100 kg 7803-52-3
88 Sulfotep 100 kg 3689-24-5
89 Sulphur dichloride 1 t 10545-99-0
90 Tellurium hexanuroride 100 kg 7783-80-4
91 TEPP 100 kg 107-49-3
92 2, 3, 7, 8-Tetrachlorodibenzo-p-dioxin
(TCDD)
1 kg 1746-01 -6
93 Tetramethylenedisulphotetramine 1 kg 80-12-6
94 Thionazin 100 kg 297-97-2
95 Tirpate (2, 4-Dimethyl-l, 3-dilhiolane-
2-carboxaldehyde O-
methylcarbarnoyloxime)
100 kg 26419-8
96 Trichloromethanesulphenyl chloride 100 kg 594-42-3
97 1-Tri (cyclohexyl) stannyl-l H-1, 2,. 4-
triazole
100 kg 41083-11-8
98 Triethylenemelamine 10 kg 51-18-3
99 Warfarin 100 kg 81-81-2
GROUP 2-TOXIC SUBSTANCES
100 Acetonecyanohydrin (2-
Cyanopropan-2-01)
200 t 75-86-5
101 Acrolein (2-Propenal) 20 t 107-02-8
102 Acrylonitrile 20 t 200 t 107-13-1
103 Allyl alcohol (Propen-1-01) 200 t 107-18-6
104 Alylamine 200 t 107-11-9
105 Ammonia 50 t 500 t 7664-41-7
106 Bromine 40 t 7726-95-6
107 Carbon disulphide 20 t 200 t 75-15-0
108 Chlorine 10 t 25 t 7782-fO 5
109 Dipneyl ethane di-isocynate (MDI) 20 t 101-68-8
110 Ethylene dibromide (1, 2-
Dibromoethane)
5 t 106-93-4
111 Ethyleneimine 50 t 151-56-4
112 Formaldehyde (concentration •90%) 5 t 50-00 0
113 Hydrogen chloride (liquified gas) 25 t 250 t 7647-01-0
114 Hydrogen cynide 5 t 20 t 74-90-8
115 Hydrogen fluoride 5 t 50 t 7664-39-3
116 Hydrogen sulphide 5 t 50 t 7783-06-4
117 Methyl bromide (Bromomethane) 20 t 74-83-9
118 Nitrogen oxides 50 t 11104-93-1
119 Propylineimine 50 t 75-55-8
120 Sulphur dioxide 20 t 250 t 7446-09-5
121 Sulphur trioxide 15 t 75 t 7446-11-9
122 Tetraethyl Iead 5 t 78-00-2
123 Tetramethyl Iead 5 t 75-74-1
124 Toluene di-isocvnate (TDI) 10 t 584-84-9
75-01-4
GROUP 3--HIGHLY REACTIVE SUBSTANCES
125 Acetylene (ethyne) 5 t 74-86-2
126 a. Ammonium nitrate (1) 350 t 2500 t 6484-52-2
b. Ammonium nitrate in form of
fertiliser (2)
1250 t
127 2 2-Bis (tert-butylperoxy) butane)
(eoncentration •70%)
5 t 2167-23-9
128 1 I-Bis (tert-butylperoxy) cyclohexane
(concentration •80%)
5 t 3006-86-8
129 tert-Butyl proxyacetate (concentration
•70%)
5 t 107-71-1
130 Tert-Butyl peroxyisobutyrate
(concentration-- •80%)
5 t 109-13-7
131 tert-Butyl peroxy isopropyl carbonate
(concentration-•80%)
5 t 2372-21-6
132 tert-Butyl peroxymaleate
(concentration-•80%)
5 t 1931-62-0
133 Tert-Butyl peroxypivalate
(concentration •77%)
50 t 927-07-1
134 Dibenzyl peroxydicarbonate
(concentration •90%)
5 t 2144-45-8
135 Di-sec-butyl peroxydicarbonate
(concentration •80%)
5 t 19910-65-7
136 Diethyl peroxydicarbonate
(concentration •30%)
50 t 14666-78-5
137 2, 2-dihydroperoxypropane
(concentration •30%)
5 t 2614-76-08
138 Di-isobutyryl peroxide concentration
•50%)
50 t 3437-84-1
139 Di-n-propyl peroxydicarbonate
(concentration •80%)
5 t 16066-38-9
140 Ethylene oxide 5 t 50 t 75-21-8
141 Ethyl nitrate 50 t 625-58-1
142 3, 3, 6, 6, 9, 9Hexamcthyl-1, 2, 4, 5-
tert oxacyclononane (concentration
•75%)
50 t 22397-38-7
143 Hydrogen 2 t 50 t 1333-74-0
144 Liquid Oxygen 200 t 7782-41-7
145 Methyl ethyl ketone peroxide
(concentration •60%)
50t 1338-23-4
146 Melhyl isobutyl ketone peroxide
(concentration •60%)
50 t 37206-20-5
147 Peracelic acid (concentration •60%) 50 t 79-21-0
148 Propylene oxide 50 t 75-56-9
149 Sodium chlorate 25 t 7775-09-9
GROUP 4-EXPLOSIVE SUBSTANCES
150 Barium azide 50 t 18810-58-7
151 Bis (2,4, 6-trinilrophenyl) amine 50 t 131-073-7
152 Chlorotrinitro benzene 50 t 28260-61-9
153 Cellulose nitrate (containing 12.6%
Nitrogen)
50 t 9004-70-0
154 Cyclotetramethyleneteranitramine 50 t 2691-41-0
155 Cyclotrimetylenetiranitramine 50 t 121-82-1
156 Diazodinitrophenol 10 t 7008-81-3
157 Diethylene glycol dinitrate 10 t 693-21-0
158 Dinitrophenol, salts 50 t
159 Ethylene glycol dinitrate 10 t 628-96-6
160 1-Gyanyl-4-nitrosaminoguanyl-1-
tetrazene
10 t 109-27-3
161 2, 2', 4, 4,' 6, 6'-Hexanirostilbene 50 t 20062-22-0
162 Hydrazine nitrate 50 t 13464-97-6
163 Lead azide 50 t 13424-46-9
164 Lead styphnate (Lead 2, 4, 6-
trinitroresorcinoxide)
50 t 15245 44-0
165 Mercury fuliminate 10 t 20820-45-5
628-86-4
166 N-Methyl-N, 2, 4, 6-tetranitroaniline 50 t 479-45-8
167 Nitroglycerine 10 t 10 t 55-63-0
168 Pentacrythritol tetranitrate 50 t 78-11-5
169 Picric acid (2, 3, 6-Tr.nitrophenol) 10 t 88-89-1
170 Sodium picramate 50 t 831-52-7
171 Styphnic acid (2, 4, 6-
Trinitroresorcinol)
50 t 82-71-3
172 1, 3, 5-Triamino-2, 4, 6-
trinitrobenzene
50 t 3058-38-6
173 Trinitroaniline- 50 t 2695242-1
174 2, 4, 6-Trinitroanisole 50 t 606-35-9
175 Trinitrobenzene 50 t 25377-32-6
176 Trinitrobenzoic acid 50 t 35860-50-5
129-66-8
177 Trinitrocresol 50 t 2890S-71-
7
178 2,4, 6-Trinitrophenitolc 50 t 47324-3
179 2,4, 6-Trinitrotulene 50 t 50 t 118-96-7
PART-II
Classes of chemicals not specifically named in Part-I
1 2 3 4 5
GROUP 5-FLAMMABLE CHEMICALS
1 Flammable gases:
Substances which in the gaseous state
normal pressure and mixed with air
become flammable and the boiling point
of which at normal pressure is 20°C or
below;
15 t 200 t
2 Highly flammable liquids:
Substances which have a flash point
lower than 23°C and the boiling point Of
which at normal pressure is above 20°C;
1000 t 50,000 t
3 Flammable liquids:
Substances which have a Rash point
lower than 65ø C and which remain
liquid under pressure, where particular
processing conditions, such as high
pressure and high temperature, may
create major accident hazards.
25 t 200 t
(1) This applies to ammonium nitrate and mixtures of ammonium nitrate where
the nitrogen content derived from the ammonium nitrate is greater than 28% by
weight and aqueous solutions of ammonium nitrate where the concentration of
ammonium nitrate is greater than 90% by weight.
(2) This applies to straight ammonium nitrate fertilizers and to compound
fertilizers where the nitrogen content derived from the ammonium nitrate is greater
than 28% by weight (acompound fertilizer contains ammonium nitrate together
with phosphate and/or potash).
SCHEDULE 4
(See rule 2(d) (i)]
1. Installations for the production, processing or treatment of organic or inorganic
chemicals using for this purpose, among others:
(a) alkylation
(b) Amination by ammonolysis
(c) carbonylatin
(d) condensation
(e) dehydrogenation
(f) esterfication
(g) halogenation and manufacture of halogens
(h) hydrogenation
(i) hydrolysis
(j) Oxidation
(k) polymerization
(l) sulphonation
(m) desulphurization, manufacture and transformation of sulphur-containing
compounds
(n) nitration and manufacture of nitrogen-containing compounds
(o) manufacture of phosphorons-containing compounds
(p) formulation of pesticides and of pharmaceutical products
(q) distillation
(r) extraction
(s) solvation
(t) mixing
2. Installations for distillation, refining or other processing of petroleum or petroleum
products.
3. Installations for the total or partial disposal of solid or liquid substances by
incineration or chemical decomposition.
4. Installations for production, processing or treatment of energy gases, for example,
LPG, LNG, SNG.
5. Installations for the dry distillation of coal or lignite.
6. Installations for the production of metals or non-metals by a wet process or by
means of electrical energy.
SCHEDULE 5
[See rule 3 (2) and (3)]
SAFETY DATA SHEET
1. CHEMICAL IDENTITY
----------------------------------------------------------------------
Chemical Name Chemical Classification
----------------------------------------------------------------------
Synonyms Trade Name
----------------------------------------------------------------------
Formula C.A.S. No. U.N.No. :
----------------------------------------------------------------------
Regulated Shipping Name Hazchem No. :
Identification Codes/Label
----------------------------------------------------------------------
Hazardous Waste
I.D.No. :
----------------------------------------------------------------------
Hazardous Ingredients C.A.S. No. Hazardous Ingredients C.A.S.No.
----------------------------------------------------------------------
1. 3.
----------------------------------------------------------------------
2. 4.
----------------------------------------------------------------------
2. PHYSICAL AND CHEMICAL DATA
----------------------------------------------------------------------
Boiling Range/Point `C Physical State Appearance
----------------------------------------------------------------------
Melting/Freezing Point `C Vapour Pressure Odour
@ 35`C mm/Hg
----------------------------------------------------------------------
Vapour Density Solubility in water @30`C Others
(Air = 1)
----------------------------------------------------------------------
Specific Gravity pH
Water = 1
----------------------------------------------------------------------
3. FIRE AND EXPLOISON HAZARD DATA
----------------------------------------------------------------------
Flammability Yes/No LEL %Flash Point `C Autoignition `C
Temperature
----------------------------------------------------------------------
TDG Flammability UEL % Flash Point `C
----------------------------------------------------------Hazardous
Explosion Sensitivity to Explosion Sensitivity Combustion
Impact to State Electricity Products
----------------------------------------------------------------------
Hazardous Polymerisation
----------------------------------------------------------------------
Combustible Liquid Explosive Corrosive
Material Material
----------------------------------------------------------------------
Flammable Material Oxidiser Others
----------------------------------------------------------------------
Pyrophoric Material Organic Peroxide
----------------------------------------------------------------------
4. REACTIVITY DATA
----------------------------------------------------------------------
Chemical
Stability
----------------------------------------------------------------------
Incompatibility
with other Material
----------------------------------------------------------------------
Reactivity
----------------------------------------------------------------------
Hazardous Reaction
Products
----------------------------------------------------------------------
5. HEALTH HAZARD DATA
----------------------------------------------------------------------
Routs of
Entry
----------------------------------------------------------------------
Effects of
Exposure/Symptoms
----------------------------------------------------------------------
Emergency
Treatment
----------------------------------------------------------------------
TLV (ACG1H) ppm mg/m3 STEL ppm mg/m3
----------------------------------------------------------------------
Permissible
Exposure Limit ppm mg/m3 Odour Threshold ppm mg/m3
LD50
----------------------------------------------------------------------
NEPA Hazard Health Flammability Stability Special
Signals
----------------------------------------------------------------------
6. PREVENTIVE MEASURES
----------------------------------------------------------------------
Personnel
Protective
Equipment
----------------------------------------------------------------------
Handling and
Storage
Precautions
----------------------------------------------------------------------
7. EMERGENCY AND FIRST AID MEASURE
----------------------------------------------------------------------
FIRE FIRE EXTINGUISHING
Media
----------------------------------------------------------------------
Special procedures
FIRE -------------------------------------------------------
Unusual Hazards
----------------------------------------------------------------------
First Aid Measures
EXPOSURE -------------------------------------------------------
Antidotes/Dosages
----------------------------------------------------------------------
Steps to be taken
SPILLS -------------------------------------------------------
Waste Disposal Method
----------------------------------------------------------------------
8. ADDITIONAL INFORMATION/REFERENCES
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
9. MANUFACTURER/SUPPLIERS DATA
----------------------------------------------------------------------
Xontact Person
Name of Film in Emergency
Mailing Address ---------------------------------------------
Telephone/Telex Nos. Local Bodes
Telegraphic Address involved
--------------------------------------------
Standard
Packing
---------------------------------------------
Tremcard
Details/Ref
---------------------------------------------
Others
----------------------------------------------------------------------
10. DISCLAIMER
----------------------------------------------------------------------
Information contained in this material data sheet is believed to be reliable but no
representation, guarantee or warranties of any kind are made as to its accuracy,
suitability for a particular application or results to be obtained from them. It is upto the
manufacturer/seller to ensure that the information contained in the material safety data
sheet is relevant to the product manufactured/ handled or sold by him as the case may
be. The Government makes no warranties expressed or implied in respect of the
adcquacy of this document for any particular purpose.
SCHEDULE 6
[See rule 5(1)]
INFORMATION TO BE FURNISHED REGARDING NOTIFICATION OF A MAJOR
ACCIDENT
Report number............
of a particular accident.
1. General data
(a) Name of the site
(b) Name and address of the manufacturer
((Also state telephone/telex number)
(c) (i) Registration number
(ii)Licence number
(As may have been allotted under any
status applicable to the site, e.g.
the Factories Act)
(d) (i) Nature of industrial activity
(Mention what is actually
manufactured, stored etc.)
(ii)National Industrial Classification.
1987 at the four digit level.
_______ _____ _____ _____
2. Type of major accident
Explosion Fire Emission of dangerous
Substance
Substance(s) Emmited.................................
3. Description of the major accident
(a) Date, shift and hour of the accident
(b) Department/Section and exact place where the accident
took place
(c) The process/operation undertaken in the Department/
Section where the accident took place.
(Attach a flow chart if necessary)
(d) The circumstances of the accident of the dangerous
substance involved.
4. Emergency Measures taken and measures envisaged to be taken
to be taken to alleviate short term effects of the accident.
5. Cause of the major accident. ...................
Known(to be specified)
6. Not known ...................
Information will be supplied as ...................
soon as possible.
6. Nature and extent of damage
(a) Within the establishment - casualties
..............................Killed
..............................Injured
..............................Poisoned
Persons exposed to the major accident ................
material damaged ..............
danger is still present ..............
(b) Outside the establishment casualties
...............................Killed
...............................Injured
...............................Poisoned
Persons exposed to the major accident ..................
material damaged ................
damage to environment ................
the danger is still present ................
the danger no longer exists ................
7. Data available for assessing the effects of
the accident on persons and environment.
8. Steps already taken or envisaged
(a) to alleviate medium or long term effects
of the accident.
(b) to prevent recurrence of similar major accident.
(c) Any other relevant information.
SCHEDULE 7
[See rule 7, 9, 10 (3)]
INFORMATION TO BE FURNISHED FOR THF NOTIFICATION OF SITES
PART-I
Particulars to be included in a notification of a site.
1. The name and address of the employer making the notification.
2. The full postal address of the site where the notifiable industrial activity will be
carried on.
3. The area of the site covered by the notification and of any adjacent site which is
required to be taken into account by virtue of b(ii) of Schedule 2 and 3.
4. The date on which it is anticipated that the notifiable industrial activity will
commence, or if it has already commenced a statement to that effect.
5. The name and maximum quantity liable to be on the site of each dangerous
substance for which notification is being made.
6. Organisation structure namely organisation diagram for the proposed industrial
activity and set up for ensuring safety and health.
7. Information relating to the potential for major accidents, namely-
(a) identification of major accident hazards;
(b) the conditions or the events which could be significant in bringing one about;
(c) a brief description of the measures taken.
Information relating to the site namely-
(a) a map of the site and its surrounding area to a scale large enough to show any
features that may be significant in the assessment of the hazard or risk associated
with the site,-
(i) area likely to be affected by the major accident.
(ii) population distribution in the vicinity.
(b) a scale plan of the site showing the location and quantities of all significant
inventories of the hazardous chemicals;
(c) a description of the process or storage involving the hazardous chemicals and
an indication of the conditions under which it is normally held;
(d) the maximum number of persons likely to be present on site.
9. The arrangement for training of workers and equipment necessary to ensure safety
of such workers.
SCHEDULE 8
[See rule 10(1)]
INFORMATION TO BE FURNISHED INA SAFETY REPORT
1. The name and address of the person furnishing the information.
2. Description of the industrial activity, namely-
(a) site,
(b) construction design,
(c) protection zones explosion protection, separation distances.
(d) accessibility of plant,
(e) maximum number of persons working on the site and particularly of those
persons exposed to be hazard.
3. Description of the processes, namely-
(a) technical purpose of the industrial activity,
(b) basic principles of the technological process,
(c) process and safety-related data for the individual process stages,
(d) process description,
(e) safety-related types of utilities.
4. Description of the hazardous chemicals, namely-
(a) chemicals (quantities, substance data, safety-related data, toxicological data
and threshold values).
(b) the form in which the chemical may occur on or into which they may be
transformed in the event of abnormal conditions,
(c) the degree of purity of the hazardous chemical
5. Information on the preliminary hazard analysis, namely-
(a) types of accident
(b) system elements or events that can lead to a major accident,
(c) hazards.
(d) safety-relevant components.
6. Description of safety-relevant units, among others,
(a) Special design criteria,
(b) controls and alarms,
(c) special relief systems,
(d) quick-acting valves,
(e) collecting tanks/dump tank,
(f) sprinkler system.
(g) fire-fighting etc.
7. Information on the hazard assessment, namely--
(a) identification of hazards,
(b) the cause of major accidents,
(c) assessment of hazards according to their occurrence frequency,
(d) assessment of accident consequences,
(e) safety systems,
(f) known accident history.
8. Description of information on organisational systems used to carry on the industrial
activity safety, namely-
(a) maintenance and inspection schedules,
(b) guidelines for the training of personnel,
(c) allocation and delegation of responsibility for plant safety,
(d) implementation of safety procedures.
9. Information on assessment of the consequences of major accidents, namely-
(a) assessment of the possible release of hazardous chemicals or of energy
(b) assessment of the effects of the releases (size of the affected area, health
effects, property damage)
10. Information on the mitigation of major accidents, namely-
(a) fire brigade
(b) alarm systems,
(c) emergency plan containing system of organisation used to fight the emergency,
the alarm and the communication rules, guidelines for fighting the emergency,
information about hazardous chemicals, examples of possible accident sequences,
(d) coordination with the District Emergency authority and its off-site emergency
plan,
(e) notification of the nature and scope of the hazard in the event of an accident,
(f) antidotes in the event of a release of a hazardous chemical.
SCHEDULE 8-A
[See rule13 (1)]
DETAILS TO BE FURNISHED IN THE ON-SITE EMERGENCY PLAN
1 Name and address of the person furnishing the information.
2 Key personnel of the organization and responsibility assigned to them in case of
emergency
3 outside organizations, if involved, in assisting during on-emergency;
(a) Types of accidents
(b) Responsibility assigned
4 Details of liaison arrangements between the organization
5 Information of preliminary hazards analysis
(a) types of accidents
(b) system elements or events that can lead to a major accident.
(c) Hazards
(d) Safety relevant components
6 Details about the site
(e) location of dangerous substances
(f) seat of key personnel
(g) Emergency control room
7 Description of hazardous chemicals at plant site
(a) chemicals quantities and toxicological data
(b) transformation, if any which could occur
(c) purity of hazardous chemicals
8 Likely danger in the plant
9 Enumerate effects of:
(i) Stress and strain caused during normal operation;
(ii) Fire and explosion in side the plant and effects, if any fire and
explosion outside
10 Details regarding:
a. warning alarm and safety and security system
b. alarm and hazard control plan in line with disaster control
planning, ensuring the necessary technical and organizational
precautions;
c. reliable measuring instruments, control units and serving of
such equipments;
d. precautions in designing of the foundation and load bearing
parts of the building;
e. continuous surveillance of operations;
f. maintenance and repair work according to the generally
recognized rules of good engineering practices.
11 Details of communication facilities available during emergency and those
required for an off-site emergency;
12 Details of fire fighting and other facilities available and those required for an off-
site emergency
13 Details of first-aid and hospital services available and its adequacy.
The Punjab Factories Rules.pdf
SCHEDULE III
SCHEDULE V
SCHEDULE VIII
Thermic fluid Heaters
SCHEDULE
Schedule II
SCHEDULED
SCHEDULE I
Manufacture of aerated waters and processes incidental thereto
Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc.
(a) a wash place under cover, with either-
(b) a sufficient supply of clean towels renewed daily, and soap or other suitable cleaning material.
Manufacture and repair of electric accumulators
The method of treatment shall be as follows:-
(a) The floor shall be -
(b) The work-benches shall -
Grinding or glazing of metals and processes incidental thereto
Manufacture and treatment of lead and certain compounds of lead
The method of treatment shall be as follows:-
Applying to all the works in Appendix `A’
PART IV
Risks of Toxic Substances
PART V
Special Provisions
PART VII
Additional Welfare Amenities
PART VIII
PART IX
PART X
Exemptions
Appendix `A’
Any works or that part of works in which –
Appendix `B’
Appendix `C’
General :
Resuscitation :
Immobilisation
Dressings :
Poisoning :
Emergency Medicines:
Manufacture of pottery
Manipulation of stone or any other material containing free silica
Manufacture or manipulation of carcinogenic dye intermediates
The benzenes, Toulenes, Xylenes, having undergone nitration once or several times ( nitro, dinitro and trinitro benzene and its homologues) and chlorinated compounds, naphalenes, having undergone nitration once or several times, anilines and its homologues( toludine, Xlidine, cuminide) anisidine, phenetidine and their chlorinated nitrated and alkylaled compounds( dimethylailine, toluylendiamine, toludine phenyhydrazine, toluylhydrazine)
APPENDIX – C
CAUTIONARY PLACARD/NOTICE
Carcinogenic dye intermediates
Manufacture or manipulation of manganese and its compounds
Previous and next
Questions people ask
Is form 351 of Punjab Factories Rules 1952 still in force?
No repeal of Punjab Factories Rules 1952 is recorded.