LawGrids logoLAWGRIDS.ORG

Form D, Punjab Factories Rules 1952: FORM No-D

Punjab Factories Rules 1952 - Form D

Text of form D

FORM No-D

FORM No-D I hereby require that in the event of my death before resuming work the balance of my pay due for the period of the leave with wages not availed of shall be paid to --------------- Who is my --------------and resides at ---------------------------------------------------- Rule 101: [Framed U/S 83 of the Act] Register to be maintained in case of exemption under Section 84 (1) Where an exemption is granted under Section 84, the Manager shall maintain a register showing the position of each worker as regards leave taken and wages granted. (2) He shall display at the main entrance of the factory, notice giving full details of the system established in the factory for leave with wages and shall send a copy of it to the Inspector. (3) No alternation shall be made in the Scheme approved by the State Government at the time of granting exemption under Section 84 of the Act without its previous sanction. CHAPTER-IX SPECIAL PROVISIONS Rule 102: [Framed U/S 87of the Act] Dangerous manufacturing process or operation The following operations when carried on in any factory are declared to be dangerous manufacturing process or operations under Section 87 of the Act :- (I) Manufacture of aerated water and processes incidental thereto. (II) Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, sliver or gold. (III) Manufacture and repair of electric accumulators. (IV) Glass manufacture. (V) Grinding or glazing of metals. (VI) Manufacture and treatment of lead and certain compounds of lead. (VII) Generation of gas from dangerous petroleum. (VIII) Cleaning, smoothening or roughening etc. of articles by a jet of sand, metal shot, grit or other abrasive propelled by a blast of compressed air of steam. (IX) Liming and tanning of raw hides and skins and processes incidental thereto. (X) Carrying on of certain processes of lead and lead material in Printing Presses and Type Foundries. (XI) Chemical works. (XII) Manufacture of pottery and ceramics. (XIII) Compression of Oxygen and Hydrogen produced by the electrolysis of water: (XIV) Manipulation of stone or any other material containing free silica; (XV) Handling and processing of asbestos, manufacture of any article of asbestos and any other process of manufacture or otherwise in which asbestos is used in any form; (XVI) Handling and manipulation of corrosive substances (XVII) Use of ovens and driers in factories (XVIII) Manufacture of Manipulation of Carcinogenic intermediates; (XIX) Process extracting vegetable oils from oil cakes in solvent extraction plants. (XX) Manufacture and manipulation of manganese and its compounds. (XXI) Protection against hazards of poisoning arising from benzene. (XXII) Carbon disulphide plants. (XXIII) Operations involving High Noise levels. (XXIV) Manufacture or manipulation of dangerous pesticides. (XXV) Manufacture of Rayon by Viscose (XXVI) Highly Flammable liquids and Flammable Compressed Gases. (XXVII) Operation in foundries (3) The provisions specified in the Schedules annexed hereto shall apply to any class or description of factories wherein dangerous operations specified in each Schedule are carried out. (2-A)(a) - for the medical examination of workers to be conducted by the certifying surgeons as required by the Schedule annexed to these rules, the occupier of the factory shall pay fee at the rate of five rupees per examination of each worker; (b) The fee prescribed in clause (a) shall be exclusive of any charges for biological, radiological or other tests which may have to be carried out in connection with the medical examination. Such charges shall be payable by the occupier; (c) The fees to be paid for medical examination shall be paid into the local treasury under the head of account 0230-Labour and Employment (Provincial) fee realized under the Factories Act, 1948", or though a crossed cheque on the State Bank of India, or through postal order drawn in favour of the Chief Inspector; (3) Wherever a periodical medical examination has been prescribed under the different schedules, the occupier shall send a return in Form No. 34, to the Chief Inspector of Factories, so as to reach him on or before the 5th of every month in respect of medical examination of the workers conducted during the preceding month. (4) Notwithstanding anything contained in the Schedules annexed to this rule, the Inspector may issue order in writing to the Manager or Occupier or both, directing them to carry such measures, and within such time, as may be specified in such order with a view to remove conditions dangerous to the health of the worker or to suspend any process, where such process constitutes in the opinion of the Inspector imminent danger of poisoning or toxicity. (5) Any register or record of medical examinations and tests connected therewith required to be carried out, under any of the Schedule annexed hereto, in respect of any worker, shall be kept readily available to the Inspector and shall be preserved till the expiry of a period of one year after the worker ceases to be in employment of the factory. SCHEDULE I Manufacture of aerated waters and processes incidental thereto 1. Fencing of machines. - All machines for filling bottles or syphons shall be so constructed, placed or fenced, as to prevent, as far as may be practicable, a fragment of a bursting bottle or syphon form striking any person employed in the factory. 2. Face guards and gauntlets. – (1) The occupier shall provide and maintain in good condition for the use of all persons engaged in filling bottles or siphons: - (a) suitable face guards to protect the face, neck and throat; and (b) suitable gauntlets for both arms to protect the whole hand and arms Provided that:- (i) paragraph 2(1) shall not apply where bottles are filled by means of an automatic machine so constructed that no fragment of a bursting bottle can escape. (ii) Where a machine is so constructed that only one arm of the bottler at work up to it is exposed to danger, a gauntlet need not be provided for the arm which is not exposed to danger. (2) The Occupier shall provide and maintain in good condition for the use of all persons engaged in corking, crowning, screwing, wiring , foiling, capsuling, sighting or labelling bottles or syphons - ( a) suitable face-guards to protect the face, neck and throat; and (b) suitable gauntlets for both arms to protect the arm and at least half of the palm and the space between the thumb and forefinger. (3) Wearing of face guards and gauntlets. - All persons engaged in any of the processes specified in paragraph 2 of this schedule shall, while at work in such processes, wear the face guards and gauntlets provided under the provisions of the said paragraph. Schedule – II Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. 1. Definitions - For the purposes of this Schedule – (a) “electrolytic process” means the electrolytic plating or oxidation of metal articles by the use of an electrolyte containing acids ,bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold, etc. (b) “bath” means any vessel used for an electrolytic process or for any subsequent process; and (c) “Employed “means employed in any process involving contact with liquid from a bath. 2. Exhaust draught :-( a) an efficient exhaust draught shall be applied to every vessel in which an electrolytic process is carried on. (b) The draught shall be provided by mechanical means and shall operate on the vapour or spray given off in the process as near as may be at the point of origin. (c) The exhaust draught appliance shall be so constructed, arranged and maintained as to prevent the vapour or spray entering into any room or place in which work is carried on. 3. Prohibition relating to women and young persons - No women, adolescent or child shall be employed or permitted to work at a bath. 4. Floor of workrooms - The floor of every workroom containing a bath shall be impervious to water. The floor shall be maintained in good and level condition and shall be washed down at least once a day. 5. Protective devices - (1) The occupier shall provide and maintain in good and clean condition the following articles of protective devices for the use of all persons employed on any process at which they are liable to come in contact with liquid from a bath and such devices shall be worn by the persons concerned (a) waterproof aprons and bibs; and (b) for persons actually working at a bath, loose fitting rubber gloves and rubber boots or other waterproof footwear, and chemical goggles. (2) The occupier shall provide and maintain for the use of all persons employed suitable accommodation for the storage and drying of protective devices. 6. Water facilities - (1) There shall be provided and maintained in good repairs for the use of all persons employed in electrolytic process and processes incidental to it- (a) a wash place under cover, with either- (i) a trough with a smooth impervious surface filled with a waste pipe , and of sufficient length to allow at least 60cms for every 5 persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60cms, or (ii) at least one wash basis for every five such persons employed at any one time, fitted with a waste pipe and having a constant supply of water laid on. (b) a sufficient supply of clean towels renewed daily, and soap or other suitable cleaning material. (2) In addition to the facility in sub-paragraph 1, an approved type emergency shower with eye fountain shall be provided and maintained in good working order. Whenever necessary, in order to ensure continuous water supply, storage tank of 1500 litres capacity shall be provided as a source of clean water for emergency use. 7. Cautionary placard - A cautionary placard in the form specified below and printed in the language of the majority of the workers employed shall be affixed in a prominent place in the factory where it can be easily and conveniently read by the workers. CAUTIONARY NOTICE Electrolytic Plating 1. Chemicals handled in this plant are corrosive and poisonous. 2. Smoking, chewing tobacco, eating food or drinking, in this area is prohibited. No food stuff or drink shall be brought in this area. 3. Some of these chemicals may be absorbed through the skin and may cause poisoning. 4. A good wash shall be taken before meals. 5 Protective devices supplied shall be used while working in this area. 6 Spillage of the chemicals on any part of the body or on the floor shall be immediately washed away with water. 7. All workers shall report for the prescribed medical tests regularly to protect their own health. 8. Medical facilities and records of examinations and tests.- (1) The occupier of every factory in which electrolytic processes are carried on shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector of Factories; (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a); and (c) maintain a sufficient supply of suitable barrier cream, ointment and impermeable water proof plaster in a separate box readily accessible to the workers ad used solely for the purpose of keeping these substances. In case cyanides are used in the both, the box shall also contain an emergency cyanide kit. (2) The medical practitioner shall examine all workers before they are employed in electrolytic processes. Such examination in case of chrome plating shall includes inspection of hands, forearms and nose and will be carried out once at least in every fortnight (3) The record of the examinations referred to in sub-paragraph (2)shall be maintained in a separate register approved by Chief Inspector of Factories which shall be kept readily available for inspection by the Inspector. 9. Medical examination by the Certifying Surgeon - (1) Every worker employed in the electrolytic processes shall be examined by a Certifying Surgeon before his first employment Such examination shall include X-ray of the chest and – (a) in case of chromium plating include examination for nasal septum perforation and test for chromium in urine; (b) in case of nickel platting, test for nickel in urine; and (c) in case of cadmium plating, test for cadmium in urine and -2 microglobulin in urine. (2) No worker shall be employed in any electrolytic process unless certified fit for such employment by the Certifying Surgeon. (3) Every worker employed in the electrolytic processes shall be re-examined by a Certifying Surgeon at least once in every year, except in case of the workers employed in cadmium, chromium and nickel plating processes for whom this examination shall be carried our once in every six months. Such re- examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified under sub-paragraph (1) excluding the X-ray of the chest which shall not be required normally to be carried out earlier then once in three years. (4) The certifying surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2) including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 34. (5) The certificate of fitness and the health register shall be kept readily available for inspection by the Inspector. (6) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the electrolytic processes on the ground that continuance therein would involve danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person declared unfit in such circumstances shall be provided with alternate placement facility unless he is fully incapacitated in the opinion of the Certifying Surgeon in which case the person affected shall be suitably rehabilitated. (7) No person who has been found unfit to work as said in sub-paragraph (6) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon after further examination, again certifies him fit for employment in these processes. Schedule – III Manufacture and repair of electric accumulators 1. Savings - This schedule shall not apply to the manufacture or repair of electric accumulators or parts thereof not containing lead or any compound of lead; or to the repair on the premises, of any accumulator forming part of a stationary battery. 2.Definitions - For the purposes of this schedule - (a) “Lead process” means the melting of lead or any material containing lead, casting, pasting, lead burning, or any other work, including trimming, or any other abrading or cutting of pasted plates, involving the use, movement or manipulation of or contact with, any oxide of lead; (b) “manipulation of raw oxide of lead” means any lead process involving any manipulation or movement of raw oxides of lead other than its conveyance in a receptacle or by means of an implement from one operation to another; 3. Prohibition relating to women and young persons - No women or young person shall be employed or permitted to work in any lead process or in any room in which the manipulation of raw oxide of lead or pasting is carried on. 4. Separation of certain processes - Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another , and from other processes :- a. manipulation of raw oxide of lend; b. pasting; c. drying of pasted plates; d. formation with lead turning (tacking)necessarily carried on in connection therewith ; and e. melting down of pasted plates. 5. Air space - In every room in which a lead process is carried on, there shall be at least 14.2 cubic meters of air space for each person employed therein, and in computing this air space no height over 3.65 meters shall be taken into account. 6. Ventilation - Every workroom shall be provided with inlets and outlets of adequate size as to secure and maintain efficient ventilation in all parts of the room. 7. Distance between workers in pasting room - In every pasting room the distance between the centre of the working position of any paster and that of the paster working nearest to him shall not be less than 1.5 meters. 8. Floor of workrooms - (1) The floor of every room in which lead process is carried on shall be – (a) of cement or similar material so as to be smooth and impervious to water; (b) maintained in sound condition; and (c) kept free from materials, plant, or other obstructions not required for, or produced in, the process carried on in the room. (2) In all such rooms other than grid casting shops the floor shall be cleansed daily after being thoroughly sprayed with water at a time when no other work is being carried on in the room. (3) In grid casting shops the floor shall be cleansed daily. (4) Without prejudice to the requirements of sub-paragraphs (1), (2) and (3), where manipulation of raw oxide of lead or pasting is carried on, the floor shall also be - (a) kept constantly moist while work is being done; (b) provided with suitable and adequate arrangements for drainage; and (c) Thoroughly washed daily by means of hose pipe. 9. Work-benches - The work-benches at which any lead process is carried on shall - (a) have a smooth surface and be maintained in sound condition; (b) be kept free from all materials or plant not required for, or produced in, the process carried out there at; and all such work-benches other than those in grid casting shops shall be cleaned daily either after being thoroughly damped or by means of suction cleaning apparatus at the time when no other work being carried on there at; and all such work-benches in grid casting shops shall be cleaned daily; and every work-bench used for pasting shall- (a) be covered throughout with sheet lead and other impervious material; (b) be provided with raised edges; (c) be kept constantly moist while pasting being carried on. 10. Exhuaght draught- The following provisions shall not be carried on without the use of an efficient exhaught draught:- (a) Melting of lead or material containing lead. (b) Manipulation of raw oxide of lead unless done in an enclosed apparatus so as to prevent the escape of dust into work-room. (e) Pasting (d) Trimming, brushing, filing or any other abrading or cutting or pasted plates giving rise to dust. (e) Lead burning other than- (i) “tacking” in the formation room (ii) Chemical burning for making of lead linings for cell cases necessarily carried on in such a manner that the application of efficient exhaught is impracticable. Such exhaught draught shall be affected by mechanical means and shall operate on the dust or fume given off as nearly as may be at the point of reason so as to prevent it entering the air of any room in which persons works. 11. Fumes and gasses from melting pots – The products of combustion produced in the heating of any melting pot shall not be allow to escape into a room in which persons work . 12. Containers for dross – A suitable receptacle with tightly fitting cover shall be provided and used for dross as it is removed from every melting pot . Such receptacle shall be kept covered while in thw work room accept when dross is being deposited therein . 13. Container for lead waste – A suitable receptacle shall be provided in every work room in which old plates and waste material which may give rise to shall be deposited . 14. Racks and shelves drying room – The racks and shelves provided in any drying room shall noy be more than 2.4 m from the floor and not more than 60 cm in width / provided that as regards racks or shelves set or drawn from both sides the total width shall noy exceed 1.2 m . Such racks and shelves shall be cleaned only after being thoroughly damped unless so efficient suction cleaning apparatus is used for this purpose. 15. Medical facilities and records of medical examination and tests ( 1) – The occupier of every factory in which manufacture and repair of electric accumulators is carried on shell – ( a) Employ a qualify medical practitioner for medical surveillance of the workers employed there in whose employment shall be subject to the approval of chief inspector ; and (c) Provided to the set medical practitioner all necessary facilities for the purpose referred to enclose (a) (2) The record of medical examinations and appropriate test carried out by the said medical practitioner shall be maintained in a separate register approved by the chief inspector .and such register shall be kept readily available for inspection by the inspector 15-A. Medical examination by the Certifying Surgeon - (1) every worker employed in a lead processes shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include test for lead in urine and blood, ALA in urine, hemoglobin content, stippling of cells and steadiness test. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 3 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests specified in sub- paragraph(1) . (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker he shall make record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment In those processes. 16. Protective clothing- protective clothing shall be provided and maintained in good condition for all person employed in- (a) Manipulation of raw oxide of lead (b) Pasting © The formation room And such clothing shall be worn by the person concerned. The protective clothing shall consist of a water-proof apron and water-proof footwear; and also as required persons employed in the manipulation of raw oxide of lead or in the pasting the head covering shall be washed daily. 17. Mess room - There shall be provided and maintained for the use of all persons employed in a lead process and remaining on the premises during the meal intervals, a suitable mess room which shall be furnished with sufficient tables and benches. The mess room shall placed under the charge of a responsible person and shall be kept clean. 18. cloak room- there shall be provided and maintained for the use of all persons employed in a lead process- (a) a cloak room for clothing put-off during working hours with adequate arrangements for drying the clothes, if wet. Such accommodation shall be separate from mess room. (b) separate and suitable arrangements for the storage of protective clothing provided as per sub-rule (16) 19. Washing facilities - (1) There shall be provided and maintained in a cleanly state and in good repair for the use of all persons employed in a lead process – (a) a wash place with either – (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having a adequate supply of water laid on . (iii) a sufficient supply of clean towels made of suitable materials renewed daily, which supply in case of pasters and person employed in manipulation of raw oxide of lead shall include a separate marked towel for each worker; and (iv) a sufficient supply of soap or other suitable cleansing material and of nail brushes. (b) There shall in addition be provided means of washing in close proximity to the rooms in which manipulation of raw oxide of lead or pasting is carried on if required by notice in writing from the Chief Inspector. 20. Time allowed for washing - Before each meal and before the end of the day’s work, at least ten minutes, in addition to the regular meal times, shall be allowed for washing to each person employed in the manipulation of raw oxide of lead or in pasting. Provided that if there is be one basin or 60 centimeters of trough for each such person, this paragraph shall not apply. 21. Facilities for bathing- sufficient bath accommodation to the satisfaction of the Chief Inspector shall be provided to all the persons engaged in manipulation of raw oxide of lead or in pasting and a sufficient supply of soap and clean towels. 22. foods, drinks etc. prohibited in work-rooms- no food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any work-room in which any lead process is carried on. Schedule – IV Glass Manufacture 1.Exemption- If the Chief Inspector is satisfied in respect of any factory or any class of process that, owing to the special methods of work or the special conditions in a factory or otherwise, any of the requirements of this schedule can be suspended or relaxed without danger to the persons employed therein, or that the application of this schedule or any part thereof is for any reason impracticable, he may be certificate in writing authorize such suspension or relaxation as may be indicated in the certificate for such period and on such conditions as he may think fit. 2. Definitions - For the purpose of this schedule - (a) “efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fumes so as to prevent them (as far as practicable under the atmospheric conditions usually prevailing) from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fume, or dust originate; (b) “lead compound” means any compound of lead other than galena which, when treated in the manner described below, yields to an aqueous solution of hydrochloric acid a quantity soluble lead compound exceeding, when calculated as lead monoxide, five percent of the dry weight of the portion taken analysis. The method of treatment shall be as follows:- A weighed quantity of the material which has been dried at 100 degrees centigrade and thoroughly mixed shall be continuously shaken for one hour at the common temperature with 1,000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filterate shall then be precipitated as lead sulphide and weighed as lead sulphate. 3. Exhaust draught - The following processes shall not be carried on except under an efficient exhaust draught or such other conditions as may be approved by the Chief Inspector :- (a) the mixing of raw materials to form a “Bator”; (b) the dry grinding, glazing and polishing of glass or any article of glass; (c) all processes in which hydrofluoric acid fumes or ammonical vapours are given off; (d) all processes in the making of furnace moulds or “pots” including the grinding or crushing of used “pots”; and (e) All processes involving the use of a dry lead compound. 4. Prohibition relating to women and young person - No woman or young person shall be employed or permitted to work in any of the operations specified in paragraph 2 or at any place where such operations are carried on. 5. Floor and work-benches - The floor and work-benches of every room in which a dry compound of lead is manipulated or in which any process is carried on giving off silica dust shall be kept moist and shall comply with the following requirements :- (a) The floor shall be - (i) of cement or similar material so as to be smooth and impervious to water; (ii) maintained in sound condition; and (iii) cleansed daily after being thoroughly spread with water at a time when no other work is being carried on the room; and (b) The work-benches shall - (i) have a smooth surface and be maintained in sound condition, and (ii) cleansed daily either after being thoroughly damped or by means of a suction cleaning apparatus at a time when no other work is being carried on thereat. 6. Use of hydrofluoric acid - The following provisions shall apply to rooms in which glass is treated with hydrofluoric acid :- (a) there shall be inlets and outlets of adequate size so as to secure and maintain efficient ventilation in all parts of the room; (b) the floor shall be covered with guttaparcha and be tight and shall slope gently down to a covered drain; (c) the workplaces shall be so enclosed in projecting hoods that openings required for the bringing in the objects to be treated shall be as small as practicable; and (d) The efficient exhaust draught shall be so contrived that the gases are exhausted downwards. 7. Storage and transport of hydrofluoric acid - Hydrofluoric acid shall not be stored or transported except in cylinders or receptacles made of lead or rubber. 8. Blow pipes - Every glass blower shall be provided with a separate blow pipe bearing the distinguishing mark of the person to whom it is issued and suitable facilities shall be readily available to every glass blower for sterilising his blow pipe. 9. Food, drinks, etc., prohibited in workrooms - No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any room or workplace wherein any process specified in paragraph 2 is carried on. 10. Protective clothing - The occupier shall provide, maintain in good repair and keep in a clean condition for the use of all persons employed in the processes specified in paragraph 2 suitable protective clothing, footwear and goggles according to the nature of the work and such clothing, footwear, etc. shall be worn by the persons concerned. 11. Washing facilities - There shall be provided and maintained in a cleanly state and in good repair for the use of all persons employed in the processes specified in paragraph 2 (a) a wash place with either - (i) a trough with a smooth impervious surface fitted with a waste pipe, without plug, and of sufficient length to allow of at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having an adequate supply of water laid on or always readily available; (b) a sufficient supply of clean towels made of suitable material renewed daily with sufficient supply of soap or other suitable cleansing material and of nail brushes; and (c) a sufficient number of stand pipes with taps the number and location of which shall be to the satisfaction of the Chief Inspector. 12. Medical facilities and record of examinations and tests - (1) The occupier of every factory in which glass manufacturing processes are carried out, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The records of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 12-A. Medical Examination by Certifying Surgeon - (1)Every workers employed in processes specified in paragraph 2 shall be examined by the Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and in suspected cases chest X-ray as well as tests for lead and urine. No worker shall be allowed to work after 15 days of first employment in the factory unless certified for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by the Certifying Surgeon at least once in every twelve calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examination carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraph (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fir for employment in the said processes on the ground that continuance therein would involve special danger to the health of worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which the person affected shall be suitable rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon , after further examination, again certifies him fit for employment in those processes. Schedule – V Grinding or glazing of metals and processes incidental thereto . 1. Definitions - For the purposes of this schedule - (a) “grindstone” means a grindstone composed of natural or manufactured sandstone but does not include a metal wheel or cylinder into which blocks of natural or manufactured sandstone are fitted; (b) “abrasive wheel” means a wheel manufactured of bonded emery or similar abrasive; (c) “grinding” means the abrasion, by aid of mechanical power, of metal, by means of a grindstone or abrasive wheel; (d) “glazing” means the abrading, polishing or finishing, by aid of mechanical power, of metal, by means of any wheel, buff, mop or similar appliance to which any abrading or polishing substance is attached or applied; (e) “racing” means the turning up, cutting or dressing of a revolving grindstone before it is brought into use for the first time; (f) “hacking’ means the chipping of the surface of a grindstone by a hack or similar tool; and (g) ) “rodding” means the dressing of the surface of a revolving grindstone by the application of a rod, bar or strip of metal to such surface. Exception - (1) Nothing in this schedule shall apply to any factory in which only repairs are carried on except any part thereof in which one or more persons are wholly or mainly employed in the grinding or glazing of metals. (2) Nothing in this schedule except paragraph 4 shall apply to any grinding or glazing of metals carried on intermittently and at which no person is employed for more than 12 hours in any week 2. Equipment for removal of dust - No racing, dry grinding or glazing shall be performed without - (a) a hood or other appliance so constructed, arranged, placed and maintained as substantially to intercept the dust thrown off; (b) a duct of adequate size, air tight and so arranged as to be capable of carrying away the dust, which duct shall be kept free from obstruction and shall be provided with proper means of access for inspection and cleaning, and where practicable, with a connection at the end remote from the fan to enable the Inspector to attach thereto any instrument necessary for ascertaining the pressure of air in the said duct; and (c) a fan or other efficient means of producing a draught sufficient to extract the dust : Provided that the Chief Inspector may accept any other appliance that is, in his opinion, as effectual for the interception, removal and disposal of dust thrown off as a hood, duct and fan would be. 3. Restriction on employment on grinding operations - Not more than one person shall at any time perform the actual process of grinding or glazing upon a grindstone, abrasive wheel or glazing appliance : Provided that this paragraph shall not prohibit the employment of persons to assist in the manipulation of heavy or bulky articles at any such grindstone, abrasive wheel or glazing appliance. 4. Glazing - Glazing or other processes, except processes incidental to wet grinding upon a grindstone shall not be carried on in any room in which wet grinding upon a grindstone is done. 5. Hacking and rodding - Hacking or rodding shall not be done unless during the process either an adequate supply of water is laid on at the upper surface of the grindstone or adequate appliances for the interception of dust are provided in accordance with the requirements of paragraph 3. 6. Examination of dust equipment - (1) All equipment for the extraction or suppression of dust shall at least once in every six months be examined and tested by competent person, and any defect disclosed by such examination and test shall be rectified as soon as practicable. (2) A register containing particulars of such examination and tests shall be kept in Form 25. 7. Medical facilities and record of examinations and tests - (1)The occupier of every factory in which grinding or glazing of metals are carried out, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 8. Medical examination by the Certifying Surgeon - (1) every worker employed in grinding or glazing of metal and processes incidental thereto shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and in suspected cases chest X-rays. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the found that continuance therein would involve special danger to the health of the worker he shall make record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 10. Exemption - The Chief Inspector may by certificate in writing, subject to such conditions as he may specify therein, relax or suspend any of the provisions of this schedule in respect of any factory if owing to the special methods of work or otherwise such relaxation or suspension is practicable without danger to the health or safety of the persons employed. Schedule – VI Manufacture and treatment of lead and certain compounds of lead 1. Exemption - Where the Chief Inspector is satisfied that all or any of the provisions of this any factory from all or any of such provisions, subject to such conditions as he may specify. schedule are not necessary for the protection of the persons employed, he may by certificate in writing exempt 2. Definitions - For this purpose of this schedule - (a) “lead compound” means any compound of lead other than galena which, when treated in the manner described below, yields to an aqueous solution of hydrochloric acid, a quantity of soluble lead compound exceeding, when calculated as lead monoxide, five per cent of the “dry weight” of the portion taken for analysis. In the case of paints and similar products and other mixtures containing oil or fat the “dry weight” means the dry weight of the material remaining after the substance has been thoroughly mixed and treated with suitable solvents to remove oil, fats, varnish or other media. The method of treatment shall be as follows:- A weighed quantity of the material which has been dried at 100 degree centigrade and thoroughly mixed shall be continuously shaken for one hour, at the common temperature with 1,000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filtrate shall then precipitate as lead sulphate and weighed as lead sulphate; (b) “efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fumes so as to prevent them (as far as practicable under the atmospheric conditions usually prevailing) from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fume, or dusts originate. 3. Application - This schedule shall apply to all factories or parts of factories in which any of the following operations are carried on :- (a) work at a furnace where the reduction or treatment of zinc or lead ores is carried on ; (b) the manipulation, treatment or reduction of ashes containing lead, the desilvering of lead or the melting of scrap lead or zinc; (c) the manufacture of solder or alloys containing more than ten percent of lead; (d) the manufacture of any oxide, carbonate, sulphate, chromate, acetate, nitrate or silicate of lead; (e) the handling or mixing of lead tetra-ethyl; (f) any other operation involving the use of a lead compound; and (g) The cleaning of workrooms where any of the operations aforesaid are carried on. 4. Prohibition relating to women and young persons - No women or young person shall be employed or permitted to work in any of the operations specified in paragraph 1. 5. Requirements to be observed - No person shall be employed or permitted to work in any process involving the use of lead compounds if the process is such that dust or fume from a lead compound is produced therein, or the persons employed therein are liable to be splashed with any lead compound in the course of their employment unless the provisions of paragraphs 5 to 13 are complied with. 6. Exhaust draught - Where dust, fume, gas or vapour is produced in the process, provision shall be made for removing them by means of an efficient exhaust draught to contrived as to operate on the dust, fume, gas or vapour as closely as possible to the point of origin. 7. Medical facilities and record of examinations and tests - (1) The occupier of every factory in which grinding or glazing of metals are carried out, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 8. Medical examination by the Certifying Surgeon - (1) every worker employed shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and in suspected cases chest X- rays. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 3 calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker he shall make record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 9. Food, drinks, etc. prohibited in workroom - No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any worker in any workroom in which the process is carried on and no person shall remain in any such room during intervals for meals or rest. 10. Protective clothing - Suitable protective overalls and head coverage shall be provided, maintained and kept clean by the occupier and such overalls and head coverings shall be worn by the persons employed. 11. Cleanliness of workrooms, tools, etc. - The rooms in which the persons are employed and all tools and apparatus used by them shall be kept in a clean state. 12. Washing facilities - (1)The occupier shall provide and maintain for the use of all persons employed suitable washing facilities consisting of - (a) a trough with a smooth impervious surface fitted with a waste pipe, without plug, and of sufficient length to allow of at least two feet for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or (b) At least one wash-basin for every ten persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of clean water; together with, in either case, a sufficient supply of nail brushes, soap or other suitable cleansing material and clean towels. (2) The facilities so provided shall be placed under the charge of a responsible person and shall be kept clean. 13. Mess room or canteen - The occupier shall provide and maintain for the use of the persons employed suitable and adequate arrangements for taking their meals. The arrangements shall consist of the use of a room separate from any workroom which shall be furnished with sufficient tables and benches, and unless a canteen serving hot meals is provided, adequate means of warming the food. The room shall be adequately ventilated by the circulation of fresh air, shall be placed under the charge of a responsible person and shall be kept clean. 14 Cloakroom - The occupier shall provide and maintain for the use of persons employed, suitable accommodation for clothing not worn during working hours, and for the drying of wet clothing. Schedule – VII Generating petrol gas from dangerous petroleum 1. Prohibition relating to women and young persons - No woman or young person shall be employed or permitted to work in or shall be allowed to enter any building in which the generation of gas from dangerous petroleum is carried on. 2.Flame traps - The plant for generation of gas from dangerous petroleum and associated piping and fittings shall be fitted with at least two efficient flame traps so designed and maintained as to prevent a flash back from any burner to the plant. One of these traps shall be fitted as close to the plant as possible. The plant and all pipes and valves shall be installed and maintained free form leaks. 3.Generating building or room - All plants for generation of gas from dangerous petroleum erected after the coming into force of the provisions specified in this schedule, shall be erected outside the factory building proper in a separate well ventilated building (hereinafter referred to as “generating building”). In the case of such plants erected before the coming into force of the provisions specified in this schedule, there shall be no direct communication between the room where such plants are erected (hereinafter referred to as “the generating room”) and the remainder of the factory building. So far as practicable, all such generating rooms shall be constructed of fire-resisting materials. 4. Fire extinguishers - An efficient means of extinguishing petrol fires shall be maintained in an easily accessible position near the plant for generation of gas from dangerous petroleum. 5. Plant to be approved by Chief Inspector - gas from dangerous petroleum shall not be manufactured except in a plant for generating gas, the design and construction of which has been approved by the Chief Inspector. 6. Escape of dangerous petroleum - Effective steps shall be taken to prevent dangerous petroleum from escaping into any drain or sewer. 7. Prohibition relating to smoking - No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in the generation room or building or in the vicinity thereof and a warning notice in the language understood by the majority of the workers shall be posted in the factory prohibiting smoking and the carrying of matches, fire or naked light or other means of producing a naked light or spark into such room or building. 8. Access to dangerous petroleum or container - No unauthorized person shall have access to any dangerous petroleum or to a vessel containing or having actually contained dangerous petroleum. 9. Electric fittings - All electric fittings shall be of flameproof construction and all electric conductors shall either be enclosed in metal conduits or be lead-sheathed. 10.Construction of doors - All doors in the generating room or building shall be constructed to open outwards or to slide and no door shall be locked or obstructed or fastened in a such a manner that it cannot be easily and immediately opened from the inside while gas is being generated and any person is working in the generating room or building. 11.Repair of containers- No vessel that has contained dangerous petroleum shall be repaired in a generating room or building and no repairs to any such vessel shall be undertaken unless live steam has been blown into the vessel and until the interior is thoroughly steamed out or other equally effective steps have been taken to ensure that it has been rendered free from dangerous petroleum or inflammable vapour. Schedule – VIII Cleaning or smoothing, roughening, etc. of articles, by a jet of sand, metal shot, or grit, or other abrasive propelled by a blast of compressed air or steam (Blasting Regulations) 1. Definitions - For the purposes of this schedule - (a) “blasting” means cleaning, smoothing, roughening, or removing of any part of the surface of any article by the use of an abrasive of a jet of sand, metal shot, or grit or other material, propelled by a blast of compressed air or steam ; (b) “blasting enclosure” means a chamber, barrel, cabinet or any other enclosure designed for the performance of blasting therein; (c) “blasting chamber” means a blasting enclosure in which any person may enter at any time in connection with any work or otherwise; and (d) “cleaning of castings” where done as an incidental or supplemental process in connection with the making of metal castings, means the freeing of the casting from adherent sand or other substance and includes the removal of cores and the general smoothening of a casting, but does not include the free treatment. 2. Prohibition of sand blasting - Sand or any other substance containing free silica shall not be introduced as an abrasive into any blasting apparatus and shall not be used for blasting : Provided that this clause shall come into force two years after the coming into operation of this schedule. Provided further that no woman or young person shall be employed or permitted to work at any operation of sand blasting. 3. Precautions in connection with blasting operations - (A)Blasting shall not be done except in a blasting enclosure and no work other than blasting and any work immediately incidental thereto and clearing and repairing of the enclosure including the plant and appliances situated therein, shall be kept closed and air tight while blasting is being done therein. (B) Maintenance of blasting enclosure: Blasting enclosure shall always be maintained in good condition and effective measures shall be taken to prevent dust escaping from such enclosure, and from apparatus connected therewith, into the air of any room. (C) Provision of separating apparatus: There shall be provided and maintained for and in connection with every blasting enclosure, efficient apparatus for separating, so far as practicable, abrasive which has been used for blasting and which is to be used again as an abrasive, from dust or particles of other materials arising from blasting; and no such abrasive shall be introduced into any blasting apparatus and used for blasting until it has been so separated : Provided that this clause shall not apply, except in the case of blasting chambers, to blasting enclosures constructed or installed before the coming into force of this schedule, if the Chief Inspector is of opinion that it is not reasonably practicable to provide such separating apparatus. (D) Provision of ventilating plant: There shall be provided and maintained in connection with every blasting enclosure efficient ventilating plant to extract, by exhaust draught effected by mechanical means, dust produced in the enclosure. The dust extracted and removed shall be disposed of by such method and in such manner that it shall not escape into the air of any room; and every other filtering or settling device situated in a room in which persons are employed, other than persons attending to such bag or other filtering or settling device, shall be completely separated from the general air of that room in an enclosure ventilated to the open air. (E) Operation of ventilating plant: The ventilating plant provided for the purpose of sub- paragraph (4) shall be kept in continuous operation whenever the blasting enclosure is in use whether or not blasting is actually taking place therein, and in the case of a blasting chamber, it shall be in operation even when any person is inside the chamber for the purpose of cleaning. 4. Inspection and examination - (1) Every blasting enclosure shall be specially inspected by a competent person at least once in every week in which it is used for blasting. Every blasting enclosure, the apparatus connected therewith and the ventilating plant shall be thoroughly examined and in the case of ventilating plant, tested by a competent person at least once in every month. (2) Particulars of the result of every such inspection, examination or test shall forthwith be entered in a register which shall be kept in a form approved by the Chief Inspector and shall be available for inspection by any workman employed in or in connection with blasting in the factory. Any defect found on any such inspection, examination or test shall be immediately reported by the person carrying out the inspection, examination or test to the occupier, manager or other appropriate person and without prejudice to the foregoing requirements of this schedule, shall be removed without avoidable delay. 5. Provision of protective helmets, gauntlets and overalls - (1) There shall be provided and maintained for the use of all persons who are employed in a blasting chamber, whether in blasting or in any work connected therewith or in cleaning such a chamber, protective helmets of a type approved by a certificate of the Chief Inspector; and every such person shall wear the helmet provided for this use whilst he is in the chamber and shall not remove it until he is outside the chamber. (2) Each protective helmet shall carry a distinguishing mark indicating the person by whom it is intended to be used and no person shall be allowed or required to wear a helmet not carrying his mark or a helmet which has been worn by another person and has not since been thoroughly disinfected. (3) Each protective helmet when in use shall be supplied with clean and not unreasonably cold air at a rate of not less 170 litres per minute. (4) Suitable gauntlets and overalls shall be provided for the use of all persons while performing blasting or assisting at blasting, and every such person shall while so engaged, wear the gauntlet and overall provided. 6. Precautions in connection with cleaning and other work - (1) Where any person is engaged upon cleaning of any blasting apparatus or blasting enclosure or of any apparatus or ventilating plant connected therewith or the surroundings thereof or upon any other work in connection with any blasting apparatus or blasting enclosure or with any apparatus or ventilating plant connected therewith so that he is exposed to the risk of inhaling dust which has arisen from blasting, all practicable measures shall be taken to prevent such inhalation. (2) In connection with any cleaning operation referred to in paragraph 5, and with the removal of dust from filtering or settling devices all practicable measures shall be taken to dispose of the dust in such a manner that it does not enter the air of any room. Vacuum cleaners shall be provided and used wherever practicable for such cleaning operations. 7. Storage accommodation for protective wear - Adequate and suitable storage accommodation for the helmets, gauntlets and overalls required to be provided by paragraph 5 shall be provided outside and conveniently near to every blasting enclosure and such accommodation shall be kept clean. Helmets, gauntlets and overalls when not in actual use shall be kept in this accommodation. 8. Maintenance and cleaning of protective wear - All helmets, guantlets, overalls and other protective devices or clothings provided and worn for the purposes of this schedule, shall be kept in good condition and so far as is reasonably practicable shall be cleaned on every weekday in which they are used. Where dust arising from the cleaning of such protective clothing or devices is likely to be inhaled, all practicable measures shall be taken to prevent such inhalation. Vacuum cleaners shall, wherever practicable, be used for removing dust from such clothing and compressed air shall not be used for removing dust from any clothing. 9. Maintenance of vacuum cleaning plant - Vacuum cleaning plant used for the purpose of this schedule shall be properly maintained. 10. Restrictions in employment of young persons - (1) No person under 18 years of age shall be employed in blasting or assisting at blasting or in any blasting chamber or in the cleaning of any blasting apparatus or any blasting enclosure or any apparatus or ventilating plant connected therewith or be employed on maintenance or repair work at such apparatus, enclosure or plant. (2) No person under 18 years of age shall be employed to work regularly within twenty feet of any blasting enclosure unless the enclosure is in a room and he is outside that room where he is effectively separated from any dust coming from the enclosure. 11. Power to exempt or relax - (1) If the Chief Inspector is satisfied that in any factory or any class of factory, the use of sand or other substance containing free silica as an abrasive in blasting is necessary for a particular manufacture or process (other than the process incidental or supplemental to making of metal castings) and that the manufacture or process cannot be carried on without the use of such abrasive or that owing to the special conditions or special method of work or otherwise any requirement of this schedule can be relaxed without endangering the health of the persons employed or that application of any such requirements is for any reason impracticable or inappropriate, he may, with the previous sanction of the State Government, by an order in writing exempt the said factory or class of factory from such provisions of this schedule, to such an extent and subject to such conditions and for such period as may be specified in the said order. (2) Where an exemption has been granted under sub-paragraph (1), a copy of the order shall be displayed at a notice board at a prominent place at the main entrance or entrances to the factory and also at the place where the blasting is carried on. 12. Medical facilities and records of examinations and tests - (1) occupier of every factory to which the Schedule applies, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the the approval of the Chief Inspector of Factories; and (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 13. Medical examination by the Certifying Surgeon - (1) every worker employed in any of the processes to which this schedule shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and chest X-rays. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include pulmonary function test and chest X-ray once in every three years. (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker he shall make record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. Schedule – IX Liming and tanning of raw hides and skins and processes incidental thereto. 1. Cautionary notices - (1) Cautionary notices as to anthrax in the form specified by the Chief Inspector shall be affixed in prominent positions in the factory where they may be easily and conveniently read by the persons employed. (2) A copy of a warning notice as to anthrax in the form specified by the Chief Inspector shall be given to each person employed when he is engaged, and subsequently if still employed, on the first day of each calendar year. (3) Cautionary notices as to the effects of chrome on the skin shall be affixed in prominent positions in every factory in which chrome solutions are used and such notices shall be so placed as to be easily and conveniently read by the persons employed. (4) Notices shall be affixed in prominent places in the factory stating the position of the first-aid box or cupboard and the name of the person in charge of such box or cupboard. (5) If any person employed in the factory is illiterate, effective steps shall be taken to explain carefully to such illiterate person the contents of the notice specified in sub- paragraphs (1), (2) and (4) and if chrome solutions are used in the factory, the contents of the notice specified in sub-paragraph (3). 2. Protective clothing - The occupier shall provide and maintain in good condition the following articles of protective clothing :- (a) waterproof footwear leg coverings, aprons and gloves for persons employed in processes involving contact with chrome solutions, including the preparation of such solutions; (b) gloves and boots for persons employed in lime yard; (c) protective footwear, aprons and gloves for persons employed in processes involving the handling of hides and skins, other than in processes specified in sub- paragraphs (a) and (b) above : Provided that the gloves, aprons, leg coverings or boots may be of rubber or leather, but the gloves and boots to be provided under sub-paragraphs (a) and (b) shall be of rubber. Provided further that the gloves may not be provided to persons fleshing by hand or employed in processes in which there is no risk of contact with lime, sodium sulphide or other caustic liquor. 3. Washing facilities, mess room and cloakroom - There shall be provided and maintained in a clean state and in good repair for the use of all persons employed - (a) a trough with a smooth impervious surface fitted with a waste pipe, without plug, and of sufficient length to allow of at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or (b) at least on wash-basin for every ten such persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of clean water; together with, in either case, a sufficient supply of nail brushes, soap or other suitable cleansing material and clean towels; (c) a suitable mess room, adequate for the number remaining on the premises during the meal intervals, which shall be furnished with sufficient tables and benches and adequate means for warming food and for boiling water. The mess room shall – (i) be separate from any room or shed in which hides or skins are stored, treated or manipulated; (ii) be separate from the cloakroom; and (iii) be placed under the charge of a responsible person; and (d) the occupier shall provide and maintain for use of all persons employed suitable accommodation for clothing put off during working hours and another accommodation for protective clothing and also adequate arrangements for drying up the clothing in both the cases, if wet. The accommodation so provided shall be kept clean at all times and placed under the charge of a responsible person. 4. Food, drinks, etc. prohibited in workrooms - No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any workroom or shed in which hides or skins are stored, treated or manipulated. 5. Medical facilities and record of examinations and tests - (1) The occupier of every factory in which the schedule applies, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (c) arrange for inspection of the hands of all the persons keeping in contact with chromium substances to be made twice a week; and (d) Provide and maintain and supply suitable ointment and plaster in a box readily accessible to the workers and solely used for the purpose of keeping the ointment and the plaster. (2) The records of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 6. Medical Examination by Certifying Surgeon - (1) every worker employed in shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by the Certifying Surgeon at least once in every twelve calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub- paragraph (1). (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examination carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraph (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fir for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which can the person affected shall be suitable rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. Schedule – X Carrying on of certain processes of lead and lead material in Printing presses and type foundries 1. Exemption - Where the Chief Inspector is satisfied that all or any of the provisions of this schedule are not necessary for the protection of persons employed, he may by certificate in writing exempt any factory from all or any such provisions subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector. 2. Definitions - For the purpose of this schedule - (a) “lead material” means material containing not less than five per cent of lead ; (b) “lead process” means – (i) the melting of lead or any lead material for casting and mechanical composing; (ii) the recharging of machines with used lead material; (iii) any other work including removal of dross from melting pots and cleaning of plungers; and (iv) Manipulation, movement or other treatment of lead material. (c) “efficient exhaust draught” means localised ventilation effected by head or mechanical means for the removal of gas, vapour, dust or fumes so as to prevent them from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such gas, vapour, fume, or dust originate. 3. Exhaust draught - (1) None of the following processes shall be carried on except with an efficient exhaust draught unless carried on in such a manner as to prevent free escape of gas, vapour, fumes or dust into any place in which work is carried on, or unless carried on in electrically heated and thermostatically controlled melting pots:- (a) melting lead material or slugs; and (b) Heating lead material so that vapour containing lead is given off. Provided that the aforesaid processes may be carried on without efficient exhaust draught if they are carried on in such a manner as to prevent free escape of gas,vapour,fume or dust into any place in which work is being done or is carried on in electrically-heated and thermostatically controlled melting pots. (2) Such exhaust draught shall be effected by mechanical means and so contrived as to operate on the dust, fume, gas or vapour given off as closely as may be at its point of origin. 4. Prohibition relating to women and young persons. - No woman or young person shall be employed or permitted to work in any lead process. 5. Separation of certain processes.- Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another and from any other processes :- (a) melting of lead or any lead material; (b) casting of lead ingots; and (c) Mechanical composing. 6. Container for dross - A suitable receptacle with tightly fitting cover shall be provided and used for dross as it is removed from every melting pot. Such receptacle shall be kept covered while in the workroom near the machine except when the dross is being deposited therein. 7. Floor of workroom - The floor of every workroom where lead process is carried on shall be - (a) of cement or similar material so as to be smooth and impervious to water; (b) maintained in sound condition; and (a) Shall be cleansed throughout daily after being thoroughly damped with water at a time when no other work is being carried on at the place. 8. Mess room - There shall be provided and maintained for the use of all persons employed in a lead process and remaining on the premises during the meal intervals, a suitable messroom which shall be furnished with sufficient tables and benches. 9. Washing facilities - (1) There shall be provided and maintained in a cleanly state and in good repair for the use of all persons employed in a lead process – (a) a wash place with either – (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 centimetres; or (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having a adequate supply of water laid on or always readily available; and (b) a sufficient supply of clean towels made of suitable materials renewed daily, with a sufficient supply of soap or other suitable cleansing material. 10. Medical facilities and record of examination and tests:- (i) the occupier of every factory to which this Schedule applies, shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 10-A. Medical examination by Certifying Surgeon - (1) Every worker employed in a lead processes shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for lead in urine and blood. ALA in urine, haemoglobin content, stippling of cells and steadiness test. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every six calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub- paragraph (1). (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub- paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) if at any time certifying surgeon is of the opinion that a worker is no longer fit for employment in the said process on the ground that continuance therein would involve special danger to the health of the worker he shall make a record of his findings in the said Certificate and the health register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 11. Food, drinks, etc. prohibited in workrooms - No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any workroom in which any lead process is carried on. 12. The occupier shall provide to all persons employed in lead process two full sleeve overall every year, arrange for their weekly washing and maintain these in good condition. The person employed in such a process shall wear these overall while engaged in such work. Schedule – XI Chemical Works PART I 1. Application - This schedule shall apply to all manufacture and processes incidental thereto carried on in chemical works. 2. Definitions - For the purpose of this schedule – (a) “chemical works” means any factory or such parts of any factory as are listed in appendix `A’ to this schedule; (b) “efficient exhaust draught” means localised ventilation effected by mechanical or other means for the removal of gas, vapour, fume or dust to prevent it from escaping into the air of any place in which work is carried on; (c) “bleaching powder” means the bleaching powder commonly called chloride of lime; (d) “chlorate” means chlorate or perchlorate; (e) “caustic” means hydroxide of potassium or sodium; (f) “chrome process” means the manufacture of chromate or bichromate of potassium or sodium, OT the manipulation, movement or other treatment of these substances; (g) “nitro or amino process” means the manufacture of nitro or amino derivatives of phenol and of benzene or its homologues, and the making of explosives with the use of any of these substances; (h) the term `permit to work’ system means the compliance with the procedures laid down under para 20 of Part II; (i) “toxic substances” means all those substances which when they enter into the human body, through inhalation or ingestion or absorption through skin, in sufficient quantities cause fatality or exert serious affliction of health, or chronic harmful effects on the health of persons exposed to it due to its inherent chemical or biological effects. In respect of substances whose TLV is specified in Rule 123-A, exceeding the concentration specified therein would make the substance toxic; (j) “emergency” means a situation or condition leading to a circumstance or set of circumstances in which there is danger to the life or health of persons or which could result in big fire or explosion or pollution to the work and outside environment, affecting the workers or neighbourhood in a serious manner, demanding immediate action; (k) “dangerous chemical reactions” means high speed reactions, runaway reactions, delayed reactions, etc. and are characterised by evolution of large quantities of heat, intense release of toxic or flammable gases or vapours, sudden pressure build-up etc.; (l) “manipulation” means mixing, blending, filling, emptying, grinding, sieving, drying, packing, sweeping, handling, using, etc.; (m) “approved personal protective equipment” means items of personal protective equipment conforming to the relevant ISI specifications or in the absence of it, personal protective equipment approved by the Chief Inspector of Factories; (n) “appropriate personal protective equipment” means that when the protective equipment is used by the worker, he shall have no risk to his life or health or body; and (o) “confined space” means any space by reason of its construction as well as in relation to the nature of the work carried therein and where hazards to the persons entering into or working inside exist or are likely to develop during working. PART II General Requirements Applying to all the works in Appendix `A’ 1. Housekeeping – (1) Any spillage of materials shall be cleaned up before further processing. (2) Floors, platforms, stairways, passages and gangways shall be free of any obstructions. (3) There shall be provided easy means of access to all parts of the parts of the plant to facilitate cleaning. 2. Improper use of chemicals-chemicals or solvents or empty containers containing chemicals or solvents shall be permitted to be used by workers for any purpose other than in the processes for which they are supplied. 3. Prohibition on the use of food, etc. - No food, drink, tobacco, pan or any edible item shall be stored or heated or consumed on or near any part of the plant or equipment. 4. Cautionary Notices and Instructions - (1) Cautionary notices in a language understood by the majority of workers shall be prominently displayed in all hazardous areas drawing the attention of all workers about the hazards to health, hazards involving fire and explosion and any other hazard such as consequences of testing of material or substances used in the process or using any contaminated container for drinking or eating, to which the workers’ attention should be drawn for ensuring their safety and health. (2) In addition to the above cautionary notice, arrangement shall be made to instruct and educate all the workers including illiterate workers about the hazards in the process including the specific hazards to which they may be exposed to, in the normal course of their work. Such instructions and education should also deal with the hazards involved in unauthorised and unsafe practices including the properties of substances used in the process under normal conditions as well as abnormal conditions and the precautions to be observed against each and every hazard. Further, an undertaking from the workers shall be obtained within 1 month of their employment and for old workers employed, within one month of coming into operation of the rules, to the effect that they have read the contents of the cautionary notices and instructions, understood them and would abide by them. The training and instructions to all workers and all supervisory personnel shall include the significance of different types of symbols and colours used on the labels stuck or painted on the various types of containers and pipe lines. 5. Evaluation and provision of safeguards before the commencement of process - (1) Before commencing any process or any experimental work, or any new manufacture covered under Appendix `A’, the occupier shall take all possible steps to ascertain definitely all the hazards involved both from the actual operations and the chemical reactions including the dangerous chemical reactions. The properties of the raw materials used, the final products to be made and any by-products derived during manufacture, shall be carefully studied and provisions shall be made for dealing with any hazards including effects on workers, which may occur during manufacture. (2) Information in writing giving details of the process, its hazards and the steps taken or proposed to be taken from the design stage to disposal stage for ensuring the safety as in sub-para (1) above should be sent to the Chief Inspector at the earliest but in no case less than 15 days before commencing manufacture, handling, or storage of any of items covered under Appendix `A’, whether on experimental basis, or as pilot plant or as trial production, or as large scale manufacture. (3) The design, construction, installation, operation, maintenance and disposal of the buildings, plant and facilities shall take into consideration effective safeguards against all the safety and health hazards so evaluated. (4) The requirements under the sub-Para (1) to (3) shall not act in lieu of or in derogation to, any other provisions contained in any Act governing the work. 6. Authorized entry - Authorized persons only shall be permitted to enter any section of the factory or plant where any dangerous operations or processes are being carried on or where dangerous chemical reactions are taking place or where hazardous chemicals are stored. 7. Examination of instruments and safety devices - (1) All instruments and safety devices used in the process shall be tested before taking into use and after carrying out any repair to them and examined once in a month, by a competent person. Records of such tests and examinations shall be maintained in a register. (2) All instruments and safety devices used in the process shall be operated daily or as often as it is necessary, to ensure its effective and efficient working at all times. 8. Electrical installations - All electrical installations used in the process covered in Appendix `A’ shall be of an appropriate type to ensure safety against the hazard prevalent in that area such as suitability against dust, dampness, corrosion, flammability and explosivity etc. and shall confirm to the relevant ISI specifications governing their construction and use for that area. 9. Handling and storage of chemicals - (1) The containers for handling and storage of chemicals shall be of adequate strength taking into consideration the hazardous nature of the contents. They shall also be provided with adequate labelling and colour coding arrangements to enable identification of the containers and their contents indicating the hazards and safe handling methods and shall conform to the respective ISI standards. The instructions given in the label shall be strictly adhered to. Damaged containers shall be handled only under supervision of a knowledgeable and responsible person and spillage shall be rendered innocuous in a safe manner using appropriate means. (2) The arrangements for the storage of chemicals including charging of chemicals in reaction vessels and containers shall be such as to prevent any risk of fire or explosion or formation of toxic concentration of substances above the limits specified in Rule 128. (3) Without prejudice to the generality of the requirements in sub- Para (2) above, the arrangements shall have suitable ventilation facilities and shall enable the maintenance of safe levels in vessels and containers. Such arrangements shall also take into consideration, the type of flooring and the capacity of flooring and the compatibility requirements of substances with other chemicals stored nearby. (4) (a) Storage of chemicals and intermediate products, which are highly unstable or reactive or explosive shall be limited to the quantities required for two months use. (b) Whenever the quantities laid down in the above clause (a) are to be exceeded, the permission of the Chief Inspector shall be obtained. (c) Notwithstanding anything contained in clause (a) and (b) above, the Chief Inspector of Factories may direct any factory carrying out processes covered in Appendix `A’ to further limit the storage of hazardous substances to quantities less than two months on considerations of safety. (d) Standby arrangements equal to the biggest container shall always be available to transfer the toxic substances quickly into the standby storage facility if any defect develops in any of the container resulting in the release of toxic substances. (e) Any storage facility constructed using non-metallic material such as Fibreglass Reinforced Plastics (FRP), all glass vessels etc., shall have adequate strength to withstand the stress, if any, exerted by the contents and shall be properly anchored. Working platforms, access ladders, pipelines etc used in such storage facility shall not have any support on the structure of the storage facility and shall be independently supported. 10. Facility for isolation - The plant and equipment shall be so constructed and maintained as to enable quick isolation of plant or part of plant or equipment, with appropriate indication. One copy of the layout plan indicating the isolation facilities shall always be available with the security personnel, the maintenance and the health and safety personnel and these isolation facilities shall be checked for its effectiveness once in a month. 11. Personal protective equipment - (1) All workers exposed to the hazards in the processes covered by this Schedule shall be provided with appropriate and approved type of personal protective equipment. Such equipment shall be in a clean, sterile and hygienic condition before issue. (2) The occupier shall arrange to inform, educate and supervise all the workers in the use of personal protective equipment while carrying out the job. (3) As regards any doubt regarding the appropriateness of any personal protective equipment, the decision of the Chief Inspector will be final. 12. Alarm Systems - (1) Suitable and effective alarm systems giving audible and visible indications, shall be installed at the control room as well as in all strategic locations where process control arrangements are available so as to enable corrective action to be taken before the operational parameters exceed the predetermined safe levels or lead to conditions conducive for an outbreak of fire or explosion to occur. Such alarm systems shall be checked daily and tested every month at least once to ensure its performance efficiency at all times. (2) The Chief Inspector of Factories may direct such system to be installed in case of plants or processes where toxic materials are being used and spillage or leakage of which may cause wide spread poisoning in or around the plant. 13. Control of escape of substances into the work atmosphere - (1) Effective arrangements such as, enclosure, or by pass, or efficient exhaust draught, maintenance of negative pressure etc., shall be provided in all plants, containers, vessels, sewers, drains, flues, ducts, culverts, and buried pipes and equipment, to control the escape and spread or substances which are likely to give rise to fire or explosion or toxic hazards during normal working and in the event of accident or emergency. (2) In the event of the failure of the arrangements for control resulting in the escape of substances in the work atmosphere immediate steps shall be taken to control the process in such a manner, that further escape is brought down to the safe level. (3) he substances that would have escaped into the work atmosphere before taking immediate steps as required in sub-Para (2), shall be rendered innocuous by diluting with air or water or any other suitable agent or by suitably treating the substances. 14. Control of dangerous chemical reactions - Suitable provision, such as automatic and or remote control arrangements, shall be made for controlling the effects of `dangerous chemical reactions’. In the event of failure of control arrangements automatic flooding or blanketing or other effective arrangements shall come into operation. 15. Testing, examination and repair of plant & equipment - (1) All parts of plant, equipment and machinery used in the process which in the likely event of their failure may give rise to an emergent situation shall be tested by a competent person before commencing process and retested at an interval of two years or after carrying out repairs to it. The competent person shall identify the parts of the plant, equipment and machinery required to be tested as aforesaid and evolve a suitable testing procedures. In carrying out the test mentioned above in respect of pressure vessels or reaction vessels the following precautions shall be observed, namely – (a) before the test is carried out, each vessel shall be thoroughly cleaned and examined externally, and as far as practicable, internally also for surface defects, corrosion and foreign matters. During the process of cleaning and removal of sludge, if any, all due precautions shall be taken against fire or explosion, if such sludge is of pyropheric nature or contains spontaneously combustible chemicals; (b) as soon as the test is completed, the vessel shall be thoroughly dried internally and shall be clearly stamped with the marks and figures indicating the person by whom testing has been done, and the date of test; and (c) any vessel which fails to pass the test or which for any other reason is found to be unsafe for use shall be destroyed or rendered unusable under intimation to the Chief Inspector. (2) All parts of plant, equipment, machinery which is the likely event of failure may give rise to an emergent situation shall be examined once in a month by the competent person. (3) Records of testing and examination referred to in paragraphs (1) and (2) shall be maintained as long as that part of the plant, equipment and machinery are in use. (4) All repair work including alteration, modification and addition to be carried out to the plant, equipment and machinery shall be done under the supervision of a responsible person who shall evolve a procedure to ensure safety and health of persons doing the work. When repairs or modification is done on pipelines, and joints are required to be welded, butt welding of joints shall be preferred. Wherever necessary, the responsible person shall regulate the aforesaid work through a `Permit to work system’. 16. Staging - (1) All staging that is erected for the purpose of maintenance work or repair work or for work connected with entry into confined spaces and used in the processes included in Appendix `A’, shall be stable, rigid and constructed out of substantial material of adequate strength. Such staging shall conform to the respective Indian Standard specifications. (2) Staging shall not be erected over any closed or open vessel unless the vessel is so constructed and ventilated to prevent exposure of persons working on the stages. (3) All the staging constructed for the purpose of this Para shall have appropriate access which are safe and shall be fitted with proper hand rails to a height of one metre and toe board. 17. Seating Arrangements - The seating arrangements provided for the operating personnel working in processes covered in Appendix `A’ shall be located in a safe manner as to prevent the risk of exposure to toxic, flammable and explosive substances evolved in the work environment in the course of manufacture or repair or maintenance, either due to failure of plant and equipment or due to the substances which are under pressure, escaping into the atmosphere. 18. Entry into or work in confined spaces - (1) The occupier of every factory to which the provisions of this schedule apply, shall ensure the observance of the following precautions before permitting any person to enter or work inside the confined spaces - (a) identify all confined spaces and the nature of hazards that are encountered in such spaces, normally or abnormally, and arrange to develop the most appropriate safeguards for ensuring the safety and health of persons entering into or working inside, the confined spaces; (b) regulate the entry or work inside the confined spaces through a `permit to work system’ which should include the safeguards so developed as required under sub-clause (a) above; (c) before testing the confined space for entry into or work, the place shall be rendered safe by washing or cleaning with neutralising agents; or purging with steam or inert gases and making adequate forced ventilation arrangements or such measure which will render the confined space safe; (d) Shall arrange to carry out such tests as are necessary for the purpose by a competent person and ensure that the confined space is safe for the persons to enter or work. Such testing shall be carried out as often as is necessary during the course of work to ensure its continued safety; (e) shall arrange to educate and train the personnel who would be required to work in confined spaces about the hazards involved in the work. He shall also keep in readiness the appropriate and approved personal protective equipment including arrangements for, rescue resurrection and first aid, and shall arrange supervision of the work at all times by a responsible and knowledgeable person. (2) The manager shall maintain a log of all entry into or work in, confined spaces and such record shall contain the details of persons assigned for the work, the location of the work and such other details that would have a bearing on the log book so maintained shall be retained as long as the concerned workers are in service and produces to the Inspector when demanded. 19. Maintenance work etc - (1) All the work connected with the maintenance of plants and equipment including cleaning of empty containers which have held hazardous substances used in the processes covered in this Schedule, shall be carried out under `permit to work system’ employing trained personnel and under the supervision of responsible person, having knowledge of the hazards and precautions required to deal with them. (2) Maintenance work shall be carried out in such a manner that there is no risk to persons in the vicinity or to persons who pass by. If necessary, the place of such work shall be cordoned off or the presence of unconnected persons effectively controlled. 20. Permit to work system - The permit to work system shall inter-alia include the observance of the following precautions while carrying out any specified work to be subjected to the permit to work system - (a) all work subject to the permit to work system shall be carried out under the supervision of a knowledgeable and responsible person; (b) all parts of plant or machinery or equipment on which permit to work system is carried out, shall remain isolated from other parts throughout the period of permit to work and the place of work including the parts of plant, machinery shall be rendered safe by cleaning, purging, washing, etc.; (c) All work subject to the permit to work system shall have predetermined work procedures which integrate safety with the work. Such procedures shall be reviewed whenever any change occurs in material or equipment so that continued safety is ensured; (d) persons who are assigned to carry out the permit to work system shall be physically fir in all respects taking into consideration the demands and nature, of the work before entering into the confined space. Such person shall be adequately informed about the correct work procedures as well as the precautions to be observed while carrying out the permit to work system; (e) adequate rescue arrangements wherever considered necessary and adequate first aid, rescue and resurrection arrangements shall be available in good working condition near the place of work while carrying out the permit to work system, for use in emergency; (f) appropriate and approved personal protective equipment shall be used while carrying out the `permit to work system’; (g) after completion of work subject to the `permit to work system’ the person responsible shall remove all the equipment and tools and restore to the original condition so as to prevent any danger while carrying out regular process. 21. Safety sampling personnel - The occupier shall ensure the safety of persons assigned for collecting samples by instructing them on the safe procedures. Such personnel shall be provided with proper and approved personal protective equipment, if required. 22. Ventilation - Adequate ventilation arrangements shall be provided and maintained at all times in the process area where dangerous or toxic or flammable or explosive substances could be evolved. These arrangements shall ensure that concentrations, which are either harmful or could result in explosion, are not permitted to be built up in the work environment. 23. Procedures for meeting emergencies - (1) The occupier of every factory carrying out the works covered in Appendix `A’, shall arrange to identify all types of possible emergencies that could occur in the processes during the course of work or while carrying out maintenance work or repair work. The emergencies so identified shall be reviewed every year. (2) The occupier shall formulate a detailed plan to meet all such identified emergencies including arrangements for summoning outside help for rescue and fire fighting arrangements for making available urgent medical facilities. (3) The occupier shall send the list of emergencies and the details of procedures and plans formulated to meet the emergencies, to the Chief Inspector of Factories. (4) The occupier shall arrange to install distinctive and recognisable warning arrangements to caution all persons inside the plant as well as the neighbouring community, if necessary, to enable evacuation of persons and to enable the observance of emergency procedures by the persons who are assigned emergency duties. All concerned must be well informed about the warning arrangements and their meaning. The arrangements must be checked for its effectiveness every month. (5) Alternate power supply arrangements shall be made and interlocked with the normal power supply system so as to ensure constant supply of power to the facilities and equipment meant for compliance with requirements of Paragraphs 10, 11, 12, 13, 14, 18, 22, and this paragraph of Part II, Part III, Part IV and Part V of this Schedule. (6) The occupier shall arrange to suspend the further process work in a place where emergency is established and shall forthwith evacuate all persons in that area except workers who have been assigned emergency duties. (7) All the employees of the factory shall be trained about the action to be taken by them including evacuation procedures during emergencies. (8) All emergency procedures must be rehearsed every three months and deficiencies, if any, in the achievement of the objectives shall suitably be corrected. (9) The occupier shall arrange to have ten percent of the workers trained in the use of First Aid Fire Fighting appliances and in the rendering of specific hazards of the particular process. (10) The occupier shall furnish immediately on request the specific chemical identity of the hazardous substance to the treating physician where the information is needed to administer proper emergency or first-aid treatment to exposed persons. 24. Danger due to effluents - (1) Adequate precautions shall be taken to prevent the mixing of effluents from different processes and operations which may cause dangerous or poisonous gases to be evolved. (2) Effluents which contain or give rise in the presence of other effluents to poisonous gases shall be provided with independent drainage systems to ensure that they may be trapped and rendered safe. PART III Fire and Explosion Risks 1. Sources of ignition including lighting installation.- (1)No internal combustion engine and no electric motor or other electrical equipment, and fittings and fixtures capable of generating sparks or otherwise causing combustion or any other source of ignition or any naked light shall be installed or permitted to be in the process area where there could be fire and explosion hazards. (2) ll hot exhaust pipes shall be installed outside a building and other hot pipes or hot surface or surfaces likely to become hot shall be suitably protected. (3) The classification of work areas in terms of its hazard potential and the selection of electrical equipment or other equipment that could constitute a source of ignition shall be in accordance with the respective Indian Standard. (4) Where a flammable atmosphere may be prevalent or could occur, the soles of footwear worn by workers shall have no metal on them, and the wheels of trucks or conveyors shall be conductive type. (5) All tools and appliances used for work in this area shall be of non-sparking type. (6) Smoking in process areas where there are risks of fire and explosion shall be prohibited, and warning notices in the language understood by majority of workers shall be posted in the factory prohibiting smoking into specified areas. 2. Static Electricity - (1) All machinery and plant, particularly, pipe lines and belt drives, on which static charge is likely to accumulate, shall be effectively earthed. Receptacles for flammable liquids shall have metallic connections to the earthed supply tanks to prevent static sparking. Where necessary, humidity shall be regulated. (2) Mobile tanker wagons shall be earthed during filling and discharge, and precautions shall be taken to ensure that earthing is effective before such filling or discharge take place. 3. Lightning protection - Lightening protection arrangement shall be fitted where necessary, and shall be maintained. 4. Process heating - The method of providing heat for a process likely to result in fire and explosion shall be as safe as possible and where the use of naked flame is necessary, the plant shall be so constructed as to prevent any escaping flammable gas, vapour, or dust coming into contact with the flame, or exhaust gases, or other sources likely to cause ignition. Wherever possible, the heating arrangement shall be automatically controlled at a pre-determined temperature below the danger temperature. 5. Leakage of flammable liquids - (1) Provision shall be made to confine by means of bund walls, dykes, sumps etc. Possible leakages from storage vessels containing flammable liquids. (2) aste material in contact with flammable substances shall be disposed off suitably under the supervision of knowledgeable and responsible person. (3) Adequate and suitable fire-fighting appliances shall be installed in the vicinity of such vessels. 6. Safety valves - Every still and every closed vessel which gas is evolved or into which gas is passed, and in which the pressure is liable to rise above the atmospheric pressure, shall have attached to it a pressure gauge, and a proper safety valve or other equally efficient means to relieve the pressure. These appliances shall be maintained in good condition. 7. Installation of pipe line etc - All pipelines carrying flammable or explosive substances shall be protected from mechanical damage and shall be examined by a responsible person once a week to detect any deterioration or defects, or accumulation of flammable or explosive substances, and record kept of any defects found and repairs made. 8. Fire fighting systems - (1) Every factory employing 500 or more persons and carrying out processes listed in Appendix `A’ shall provide - (a) Trained and responsible fire fighting squad so as to effectively handle the fire fighting and life saving equipment in the event of fire or other emergency. Number of persons in this squad will necessarily depend upon the size of risk involved, but in no case shall be less than 8 such trained persons to be available at any time. The squad shall consist of watch & ward personnel, fire pump man and departmental supervisors and operators trained in the operation of fire &emergency services. (b) Squad leaders shall preferably be trained in a recognised government institution and their usefulness enhanced by providing residence on the premises. (c) Squad personnel shall be provided with clothing and equipment including helmets, boots and belts. (2) A muster roll showing the duties allocated to each member of the squad shall be prepared and copies supplied to each leader as well as displayed in prominent places so as to be easily available for reference in case of emergency. (3) The pump man shall be thoroughly conversant with the location of all appliances. He shall be responsible for maintaining all fire fighting equipment in proper working order. Any defect coming to his notice shall be immediately be brought to the notice of squad leader. (4) As far asis practicable, the fire pump room and the main gate(s) of the factory be connected to all manufacturing or storing areas through telephone inter lined and placed in a convenient location near such areas. PART IV Risks of Toxic Substances 1. Leakage - (1) All plants shall be so designed and constructed as to prevent the escape of toxic substance. Where necessary, separate buildings, rooms, or protective structures shall be used for the dangerous stages of the process and buildings shall be so designed as to localise any escape of toxic substances. (2) Catch pits, bund walls, dykes, or other suitable safeguards shall be provided to restrict the serious effects of such leakages. Catch pits shall be placed below joints in pipelines where there is danger involved to maintenance and other workers from such leakage. 2. Drainage - Adequate drainage shall be provided and shall lead to collection tanks specifically provided for this purpose wherein deleterious material shall be neutralised, treated or otherwise rendered safe before it is discharged into public drains or sewers. 3. Covering of vessels - (1) Every fixed vessel or structure containing any toxic substance and not so covered as to eliminate all reasonable risk of accidental contact of any portion of the body of a worker, shall be so constructed as to avoid physical contact. (2) Such vessel shall, unless its edge is at least 90 centimetres above the adjoining ground or platform, be securely fenced to a height of at least 90 centimetres above such adjoining ground or platform. (3) Where such vessels adjoin and the space between them, clear of any surrounding brick or other work is either less than 45 centimetres in width or is 45 or more centimetres in width, but is not securely fenced on both sides to a height of at least 90 centimetres, secure barriers shall be so placed as to prevent passage between them : Provided that sub-paragraph (2) of this paragraph shall not apply to - (a) saturators used in the manufacture of sulphate of ammonia; and (b) That part of the sides of brine evaporating pans which require raking, drawing or filling. 4. Continuous exhaust arrangement - (1) Any process evolving toxic vapour, gas, fume and substance shall have efficient continuous exhaust draught. Such arrangement shall be interlocked in the process control wherever possible. (2) In the event of failure of continuous exhaust arrangement means shall be provided to automatically stop the process. 5. Work Bench - All the work benches used in the processes involving the manipulation of toxic substances, shall be graded properly and shall be made of smooth impervious surface which shall be washed daily after the completion of work. 6. Waste disposal - (1) There shall be provided a suitable receptacle made of non-absorbable material with a tightly fitting cover for depositing waste material soiled with toxic substances and the contents of such receptacle shall be destroyed by burning or using other suitable methods under the supervision of a responsible person. (2) During the course of manufacture, whenever any batch or intermediate products having toxicity is rejected on considerations of quality, sufficient precautions shall be taken to render them innocuous or otherwise treat them or inactivate them, before disposal. (4) The empty containers of toxic substances shall be cleaned thoroughly before disposal under the supervision of a responsible person. PART V Special Provisions 1. Special precautions for Nitro or Amino Processes - (1) Unless the crystallised intro or amino substances or any of its liquor is broken or agitated in a completely enclosed process so as not to give rise to dust or fume, such process shall be carried on under an efficient exhaust draught or by adopting any other suitable means in such a manner as to prevent the escape of dust or fume in the working atmosphere. (2) No part of the plant or equipment or implements which was in contact with nitro or amino compounds shall be repaired, or handled unless they have been emptied and thoroughly cleaned and decontaminated. (3) Filling of containers with nitro or amino compounds shall be done only by using a suitable scoop to avoid physical contact and the drying of the containers in the stove shall be done in such a manner that the hot and contaminated air from the stove is not drawn into the work room. (4) Processes involving the steaming into or around any vessel containing nitro or amino compounds or its raw materials shall be carried out in such a manner that the steam or vapour is effectively prevented to be blown back into the working atmosphere. (5) Suitable antidotes such as methylene blue injections shall always be available at designated places of work for use during emergency involving the poisoning with nitro or amino compounds. 2. Special precautions for `chrome processes - (1) Grinding and sieving of raw materials in chrome processes shall be carried on in such a manner and under such condition as to secure effective separation from any other processes and under an efficient exhaust draught. (2) There shall be washing facilities located very near to places where wet chrome processes such as leaching, acidification, sulphate settling, evaporation, crystallisation, centrifugation or packing are carried out, to enable quick washing of affected parts of body with running water. (3) Weekly inspection of hand and feet of all persons employed in chrome process shall be done by a qualified nurse and record of such inspections shall be maintained in a form approved by the Chief Inspector of Factories. (4) There shall be always available at designated places of work suitable ointment such as glycerine, vaseline, etc. and water proof plaster in a separate box readily accessible to the workers so as to protect against perforation of nasal septum. 3. Special precautions for processes carried out in all glass vessels - (1) Processes and chemical reactions such as manufacture of vinyl chloride, benzyl chloride etc. which are required to be carried out in all glass vessels shall have suitable means like substantial wire mesh covering to protect persons working nearby in the event of breakage of glass vessel (2) Any spillage or emission of vapour from the all glass vessel due to breakage, shall be immediately inactivated or rendered innocuous by suitable means such as dilution with water or suitable solvents so as to avoid the risks of fire or explosion or health hazards. 4. Special precautions for processes involving chlorate manufacture - (1) Crystallisation, grinding or packing of chlorate shall not be done in a place used for any other purpose and such places shall have hard, smooth and impervious surface made of non-combustible material. The place shall be thoroughly cleaned daily. (2) The personal protective equipment likes overall, etc. provided for the chlorate workers shall not be taken from the place of work and they shall be thoroughly cleaned daily. (3) Adequate quantity of water shall be available near the place of chlorate process for use during fire emergency. (4) Wooden vessels shall not be used for the crystallisation of chlorate or to contain crystallised ground chlorate. 5. Special precautions in the use of plant and equipment made from reinforced plastics - (1) Alplant and equipment shall conform to appropriate Indian or any other National Standard. (2)Care shall betaken during storage, transport, handling and installation of plant and equipment to avoid accidental damage. (3) All plant and equipment shall be installed in such a way as to ensure that loads are distributed as intended in design or as per the recommendations of the manufacture. (4) All pipe work shall be supported so that total loads local to the branches on the vessel or tank do not exceed their design values. (5) After erection all plant and equipment shall be subjected to a pressure test followed by a thorough examination by a competent person. The test and examination shall be as per relevant Standard. A certificate of test and examination by a competent person shall be obtained and kept available at site. (6) All plant and equipment shall be subjected to periodical test and examination and record maintained as per Paragraph 15 in Part II of this Schedule. (7) Plant and equipment during their use shall not be subjected to over filling or over loading beyond rated capacity. PART VI Medical Requirements 1. Decontamination facilities - In all places where toxic substances are used in processes listed in Appendix `A’ the following provisions shall be made to meet an emergency: (a) fully equipped first aid box; (b) readily accessible means of drenching with water persons, parts of body of persons, and clothing of persons who have been contaminated with such toxic and corrosive substances, and such means shall be as shown in the Table below : No.of persons No. of drenching showers employed at any time showers ----------------------- ---------------------------------- Upto 50 persons 2 Between 51 to 100 3 101 to 200 3 + 1 for every 50 persons thereafter 201 to 400 5 + 1 for every 100 persons thereafter 401 and above 7 + 1 for every 200 persons thereafter (c) a sufficient number of eye wash bottles filled with distilled water or suitable liquid, kept in boxes or cupboards conveniently situated and clearly indicated by a distinctive sign which shall be visible at all times. 2. Occupational health centre - In all the factories carrying out processes covered in Appendix `A’ there shall be provided and maintained in good order an occupational health centre with facilities as per scale laid down hereunder (1) For factories employing upto workers – (a) the services of a qualified medical practitioner hereinafter known as Factory Medical Officer, available on a retainership basis, in his notified clinic near to the factory for seeking medical help during emergency. He will also carry out the pre-employment and periodical medical examinations as stipulated in paragraph 4 of this Part. (b) A minimum of five persons trained in first aid procedures, amongst whom at least one shall always be available during the working period. (c) A fully equipped first aid box. (2) For factories employing 51 to 200 workers – (a) The occupational health centre shall have a room having a minimum floor area of 15 sq.m., with floors and walls made of smooth, hard and impervious surface and shall be adequately illuminated, ventilated and equipped. (b) A part-time Factory Medical Officer will be in over all charge of the Centre who shall visit the factory minimum twice in a week and whose services shall be readily available during emergencies. (c) There shall be one qualified and trained dresser-cum-compounder on duty throughout the working period. (d) A fully equipped first aid box. (3) For factories employing above 200 workers – (a) There shall be one full-time Factory Medical Officer for factories employing upto 500 workers and one more medical officer for every 1000 workers or part thereof. (b) The occupational health centre in this case shall have a minimum of 2 rooms each having a minimum floor area of 15 sq.m. with floors and walls made of smooth, hard and impervious surface and shall be adequately illuminated, ventilated and equipped. (c) There shall be one trained nurse, one dresser-cum-compounder and one sweeper-cum-ward boy throughout the working period. (d) The Occupational Health Centre in this case shall be suitably equipped to manage medical emergencies. 3. Ambulance van - (1) In every factory carrying out processes covered in Appendix `A’, there shall be provided and maintained in good condition, a suitably constructed and fully equipped ambulance van as per Appendix `C’ manned by a full-time driver-cum- mechanic and a helper, trained in first aid for the purposes of transportation of serious cases of accidents or sickness unless arrangements for procuring such facility at short notice during emergencies have been made with the nearby hospital or other places. The ambulance van shall not be used for any purpose other than the purpose stipulated herein and will always be available near the Occupational Health Centre. (2) The relaxation to procure Ambulance Van from nearby places provided for in sub- para (1) above will not be applicable to factories employing more than 500 workers. 4. Medical examination - (1) Workers employed in processes covered in Appendix `A’ shall be medically examined by a Factory Medical Officer in the following manner – (a) Once before employment, to ascertain physical suitability of the person to do the particular job; (b) Once in a period of 6 months, to ascertain the health status of the worker, and (c) The details of pre-employment and periodical medical examinations carried out as aforesaid shall be recorded in the prescribed form. (2) Any finding of the Factory Medical Officer revealing any abnormality or unsuitability of any person employed in the process shall immediately be reported to the Certifying Surgeon who shall in turn, examine the concerned workers and communicate his findings within 30 days. If the Certifying Surgeon is of the opinion that the person so examined is required to be suspended from the process for health protection he will direct the occupier accordingly, who shall not employ the said worker in the same process. However, the person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated : Provided that the Certifying Surgeon on his own may examine any other worker whom he feels necessary to be examined for ascertaining the suitability of his employment in the process covered in Appendix `A’ or for ascertaining the health status of any other worker and his opinion shall be final. (3) No person shall be newly appointed without the Certificate of Fitness granted by the Factory Medical Officer. If the Factory Medical Officer declares a person unfit for being appointed to work in the process covered in Appendix `A’, such person shall have a right of appeal to the Certifying Surgeon, whose opinion shall be final in this regard. (4) The worker suspended from the process owing to the circumstances covered in sub-para (2) shall be employed again in the same process only after obtaining the Fitness Certificate from the Certifying Surgeon and after making entries to that effect in the health register. PART VII Additional Welfare Amenities 1. Washing facilities - (1) There shall be provided and maintained in every factory for the use of all the workers taps for washing, at the rate of one every 15 persons including liquid soap in a container with tilting arrangements and nail brushes or other suitable means for effective cleaning. Such facilities shall be conveniently accessible and shall be kept in a clean and hygienic condition. (2) If washing facilities as required above are provided for women, such facilities shall be separate for them and adequate privacy at all times shall be ensured in such facilities. 2. Mess room facilities - (1) The occupier of all the factories carrying out processes covered in Appendix `A’ and employing 50 workers or more, shall provide for all the workers working in a shift mess room facilities which are well ventilated and provided with tables and sitting facilities along with the provision of cold and hygienic drinking water facilities. (2) Such facilities shall include suitable arrangements for cleaning and washing and shall be maintained in a clean and hygienic condition. 3. Cloakroom facilities - (1) The occupier of every factory carrying out any process covered in Appendix `A’ shall provide for all the workers employed in the process cloak room facilities with lockers. Each worker shall be provided with two lockers, one for work clothing and another separately for personal clothing and the lockers should be such as to enable the keeping of the clothing in a hanging position. (2) The cloak room facilities provided in pursuance of sub-para (1) shall be located as far as possible near to the facilities provided for washing in pursuance of para 1(1). If it is not possible to locate the washing facilities the cloakroom facilities shall have adequate and suitable arrangements for cleaning & washing. 4. Special bathing facilities - (1) The occupier of any factory carrying out the process covered under Appendix `B’ shall provide special bathing facilities for all the workers employed and such facilities shall be provided at the rate of 1 for 25 workers and part thereof, and shall be maintained in a clean and hygienic condition. (2) The occupier shall insist all the workers employed in the processes covered in Appendix `B’ to take bath after the completion of the day’s or shift work using the bathing facilities so provided and shall also effectively prevent such of those workers taking bath in any place other than the bathing facilities. (3) Notwithstanding anything contained in sub-para (1) above, the Chief Inspector may require in writing the occupier of any factory carrying out any other process for which his opinion bathing facilities are essential from the health point of view, to provide special bathing facilities. PART VIII 1. Duties of workers - (1) Every worker employed in the processes covered in Appendix ‘A’ and Appendix ‘B’ shall not make safety device or appliance or any guarding or fencing arrangement, inoperative or defective and shall report the defective condition of the aforesaid arrangements as soon as he is aware of any such defect. (2)Before commencing any work, all workers employed in processes covered in Appendix ‘A’ shall check their workplace as well as the machinery, equipment or appliance used in the processes and report any mal-function or defect immediately to the supervisor or any responsible person of the management. (3) All workers shall co-operate in all respects with the management while carrying out any work or any emergency duty assigned to them in pursuance of this schedule and shall always use all the personal protective equipment issued to them in a careful manner. (4) All workers employed in the processes covered in Appendix `A’ or Appendix `B’ shall not smoke in the process area or storage area. If special facilities are provided by the management only such facilities should be used. (5) All workers employed in the processes covered in Appendix `A’ shall not remain in unauthorised place or carry cut unauthorised work or improvise any arrangement or adopt short out method or misuse any of the facilities provided in pursuance of the Schedule, in such a manner as to cause risk to themselves as well as or to others employed. (6) The workers shall not refuse undergoing medical examination as required under these rules. PART IX Restrictions on the employment of young persons under 18 years of age and women (1) The Chief Inspector of Factories may by an order in writing, restrict or prohibit the employment of women and young persons under the age of 18, in any of the processes covered in Appendix `A’ of this schedule on considerations of health and safety of women and young persons. (2) Such persons who are restricted or prohibited from working in the process due to the order issued in pursuance of sub-para (1) above shall be provided with alternate work which is not detrimental to their health or safety. PART X Exemptions 1. Power of exemption - The State Government or subject to the control of the State Government the Chief Inspector may exempt from the compliance with any of the requirements of this Schedule partly or fully, any factory carrying out processes covered in Appendix `A’, if it is clearly and satisfactorily established by the occupier that the compliance with any of the requirement is not necessary to ensure the safety and health of persons employed suitable and effective alternate arrangements are available to any of the requirements covered in this schedule. Appendix `A’ Any works or that part of works in which – (a) the manufacture, manipulation or recovery of any of the following is carried on :- (i) sodium, potassium, iron, aluminium, cobalt, nickel, copper, arsenic, antimony, chromium, zinc, selenium, magnesium, cadmium, mercury, beryllium and their organic and inorganic salts, alloys, oxides and hydroxides; (ii) ammonia, ammonium hydroxide and salts of ammonium; (iii) the organic or inorganic compounds of sulphurous, sulphuric, nitric, nitrous, hydrochloric, hydrofluoric, hydriodic, hydro sulphuric, hydrobromic, boric; (iv) cyanogen compounds, cyanide compounds, cyanate compounds; (v) phosphorous and its compounds other than oregano phosphorus insecticides. (vi) chlorine (b) hydrogen sulphide is evolved by the decomposition of metallic sulphides, or hydrogen sulphide is used in the production of such sulphides; (c) bleaching powder is manufactured or chlorine gas is produced in chlor-alkali plants; (d) (i) gas tar or coal tar or bitumen or shale oil asphalt or any residue of such tar is distilled or is used in any process of chemicals manufacture; (ii) tar based synthetic colouring matters or their intermediates are produced; (e) nitric acid is used in the manufacture of nitro compounds; (f) explosives are produced with the use of nitro compounds; (g) aliphatic or aromatic compounds or their metallic and non-metallic derivatives or substituted derivatives, such as chloroform, ethylene glycol, formaldehyde, benzyle chloride, phenol, methyl ethyl keytone peroxide, cobalt carbonyl, tungsten carbide etc. are manufactured or recovered. Appendix `B’ Concerning Special Bathing Accommodation in pursuance of Para 4 of Part IV 1. Nitro or amido processes 2. All chrome processes 3. Processes of distilling gas or coal tar or processes of chemical manufacture in which tar is used 4.Processes involving manufacture, manipulation, handling or recovery of cyanogen compound, cyanide compound, cyanate compounds 5. Processes involving manufacture of bleaching powder orproduction of chlorine gas in chlor- alkali plants 6. Manufacture, manipulation or recovery of nickel and its compounds 7.All processes involving the manufacture, manipulation or recovery of aliphatic or aromatic compounds or their derivatives or substituted derivatives. Appendix `C’ Ambulance should have the following equipment : General : • An wheeled stretcher with folding and adjusting devices; Head of the stretcher must be capable of being tilted upward; • Fixed suction unit with equipment; • Fixed oxygen supply with equipment; • Pillow with case; • Sheets; • Blankets; • Towels; • Emesis bag; • Bed pan; • Urinal; • Glass Safety equipment : • Flares with life of 30 minutes • Flood lights; • Flash lights; • Fire extinguisher dry powder type; • Insulated gauntlets. Emergency care equipment :- Resuscitation : • Portable suction unit; • Portable oxygen unit; • Bag-valve-mask, hand operated artificial ventilation unit; • Airways; • Mouth gags; • Tracheostomy adapters; • Short spine board; • I.V. Fluids with administration unit; • B.P. manometer; • Cugg; • Stethoscope Immobilisation • Long & short padded boards; • Wire ladder splints; • Triangular bandage; • Long & short spine boards. Dressings : • Gauze pads - 4” x 4” ; • Universal dressing 10” x 36” ; • Roll of aluminium foils; • Soft roller bandages 6” x 5 yards; • Adhesive tape in 3” roll; • Safety pins; • Bandage sheets; • Burn sheet. Poisoning : • Syrup of Ipecac; } } Pre packeted in doses • Activated charcoal; } • Snake bite kit; • Drinking water. Emergency Medicines: • As per requirement (under the advice of Medical Officer only) Schedule – XII Manufacture of pottery 1 Definitions - For the purposes of this schedule - (a) “pottery” includes earthenware, stoneware, porcelain, china tiles, and any other articles made from such clay or from a mixture containing clay and other materials such as quartz, flint, feldspar, and gypsum; (b) “efficient exhaust draught” means localised ventilation effected by mechanical or other means for removal of dust or fume so as to prevent it from escaping into air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove effectively dust or fume generated at the point where dust or fume originates; (c) “fettling” includes scalloping, towing, sand papering, sand sticking, brushing or any other process of cleaning of potteryware in which dust is given off; (d)“leadless glaze”means a glaze which does not contain more than one per cent of its dry weight, of a lead compound calculated as lead monoxide; (e) “low solubility glaze” means a glaze which does not yield to dilute hydrochloric acid more than five per cent of its dry weight, of a soluble lead compound calculated as lead monoxide when determined in the manner described below : A weighed quantity of the material which has been dried at 100 degrees centigrade and thoroughly mixed shall be continuously shaken for one hour at the common temperature with 1000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filtrate shall then be precipitated as lead sulphide and weighed as lead sulphide; (f) sound or powdered flint or quartz” does not include natural sands; and (g) “potter’s shop includes all places where pottery is formed by pressing or by any other process and all places where shaping, fettling or other treatment of pottery articles prior to placing for the biscuit fire is carried on. 2. Efficient exhaust draught - The following processes shall not be carried on without the use of an efficient exhaust draught - (a) all processes involving the manipulation or use of a dry and unfritted lead compound; (b) fettling operations of any kind, whether on greenware or biscuit, provided that this shall not apply to the wet fettling, and to the occasional finishing of pottery articles without the aid of mechanical power; (c) sifting of clay dust or any other material for making tiles or other articles or other articles by pressure, except where – (i) his is done in an machine so enclosed as to effectually prevent the escape of dust; or (ii) the material to be shifted is so damp that no dust can be given off; (d) pressing of tiles from clay dust, an exhaust opening being connected with each press, and pressing from clay dust of articles other than tiles, unless the material is so damp that no dust is given off; (e) fettling of tiles made from clay dust by pressure, except where the fettling is done wholly on, or with, damp material, and fettling of other articles made from clay dust, unless the material is so damp that no dust is given off; (f) process of loading and unloading of saggars where handling and manipulation of ground and powdered flint, quartz, aluminia or other materials are involved; (g) brushing of earthenware biscuit, unless the process is carried on in a room provided with efficient general mechanical ventilation or other ventilation which is certified by the Inspector of Factories as adequate having regard to all the circumstances of the case; (h) fettling of biscuitware which has been fired in powdered flint or quartz except where this is done in machines so enclosed as to effectually prevent the escape of dust; (i) where cleaning after the application of glaze by dipping or other process; (j) crushing and dry grinding of materials for pottery bodies and saggars, unless carried on in machines so enclosed as to effectively prevent the escape of dust or is so damp that no dust can be given off; (k) sieving or manipulation of powdered flint, quartz, clay grog or mixture of these materials unless it is so damp that no dust can be given off; (l) grinding of tiles on a power driven wheel unless an efficient water spray is used on the wheel; (m) lifting and conveying of materials by elevators and conveyors unless they are effectively enclosed and so arranged as to prevent escape of dust into the air in or near to any place in which persons are employed; (n) preparation or weighing out of flow material, lawning of dry colours, colour dusting and colour blowing; (o) mould making unless the bins or similar receptacles used for holding plaster of paris are provided with suitable covers; and (p) manipulation of calcined material unless the material has been made and remains so wet that no dust is given off. 4. Separation of processes - Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another, and from other wet processes:- (a) crushing and dry grinding or sieving of materials, fettling, pressing of tiles, drying of clay and greenware, loading and unloading of saggars; and (b) all processes involving the use of a dry lead compound. 4 ion on use of glaze - No glaze which is not a leadless glaze or a low solubility glaze shall be used in a factory in which pottery is manufactured. 5. Prohibition relating to women and young persons.- No woman or young person shall be employed or permitted to work in any of the operations specified in paragraph 4, or at any place where such operations are carried on. 6. potter’s wheel. - The potter’s wheel (Jolly and Jigger) shall be provided with screens or so constructed as to prevent clay scrapings being thrown off beyond the wheel. 7. Control of dust during cleaning – (1) All practical measures shall be taken by damping or otherwise to prevent dust arising during cleaning of floors. (2) Damp saw-dust or other suitable material shall be used to render the moist method effective in preventing dust rising into the air during the cleaning process which shall be carried out after work has ceased. 8. Floor of certain workrooms - The floors of potter’s shops, slip houses, dipping houses and ware cleaning rooms shall be hard, smooth and impervious and shall be thoroughly cleaned daily by an adult male using a moist method. 9. Medical facilities and records of examinations and tests - (1) The occupier of every factory in which manufacture of pottery is carried on, shall – (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 10. Medical examination by Certifying Surgeon - (1) Every worker employed in any process mentioned under paragraph 3, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for lead in urine and blood, ALA in urine, hemoglobin content, stippling of cells and. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) All persons employed in any of the processes included under sub- paragraphs 3(a) and 3(n) shall be examined by a Certifying Surgeon once in every 3 calendar months. Those employed in any other processes mentioned in the remaining sub-paragraphs of paragraph 3 shall be examined by a Certifying Surgeon one in every 3 months. Such examinations in respect of all the workers shall include all the tests as specified in sub-paragraph (1) except chest X-ray which will be once in 3 years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said process on the ground that continuance therein would involve special danger to the health of the worker he shall make a record of his findings in the said Certificate and the health register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he fully is incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 11. Protective equipment - (1) The occupier shall provide and maintain suitable overalls and hand coverings for all persons employed in process included under paragraph 3. (2) The occupier shall provide and maintain suitable aprons of a of a waterproof or similar material, which can be sponged daily, for the use of the dippers, dippers assistants, throwers, jolly workers, casters, mould makers and filter press and pug mill workers. (3) Aprons provided in pursuance of paragraph 10(2) shall be thoroughly cleaned daily by the wearers by sponging or other wet process. All overalls and head coverings shall be washed, cleaned and mended at least once a week, and this washing, cleaning or mending shall be provided for by the occupier. (4) No person shall be allowed to work in emptying sacks of dust materials, weighing out and mixing of dusty materials and charging of ball mills and plungers without wearing a suitable and efficient dust respirator. 12. Washing facilities - (1) The occupier shall provide and maintain, in a clean state and in good repair for the use of all persons employed in any of the processes specified in paragraph 3 - (a) a wash place under cover, with either – (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow of at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 centimetres; or (ii) at least one tap or stand pipe for every five such persons employed at any one time, and having a constant supply of clean water, the tap or stand pipe being spaced not less than 120 centimetres apart; and (b) a sufficient supply of clean towels made of suitable materials changed daily, with a sufficient supply of soap and nail brushes. 13. Time allowed for washing - Before each meal and before the end of the day’s work, at least ten minutes, in addition to the regular meal times, shall be allowed for washing to each person employed in any of the processes mentioned in paragraph 3. 14. Mess room - (1) There shall be provided and maintained for use of all persons remaining within the premises during the rest intervals, a suitable messroom providing accommodation of 0.93 square meter per head and furnished with - (a) a sufficient number of tables and chairs or benches with back rest; (b) arrangements for washing utensils; (c) adequate means for warming food; and (d) adequate quantity of drinking water. (2) The room shall be adequately ventilated by the circulation of fresh air and placed under the charge of a responsible person and shall be kept clean. 15. Food, drinks, etc. prohibited in workrooms - No food, drink, pan and supari or tobacco shall be brought into, or consumed by any worker in any workroom in which any of the processes mentioned in paragraph 3 are carried on and no person shall remain in any such room during intervals for meals or rest. 16. Cloakrooms etc - There shall be provided and maintained for the use of all persons employed in any of the processes mentioned in paragraph 3. (a) a cloakroom for clothing put off during working hours and such accommodation shall be separate from any mess room; and (b) Separate and suitable arrangements for the storage of protective equipment provided under paragraph 11 17. Applications - These provisions shall not apply to a factory in which any of the following articles, but no other pottery, are made :- (a) unglazed or salt glazed bricks and tiles; and (b) Architectural terra-cotta made from plastic clay and either unglazed or glazed with a leadless glaze only. . 18. Exemption - If in respect of any factory the Chief Inspector of Factories is satisfied that all or any of the provisions of this schedule are not necessary for the protection of the persons employed in such factory, he may by a certificate in writing exempt such factory from all or any of such provisions, subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector without assigning any reasons. Schedule – XIII Compression of oxygen and hydrogen produced by electrolysis of water 1. Location of electrolyte plant - The room in which electrolysis plant is installed shall be separate from the plant for storing and compressing the oxygen and hydrogen and also the electric generator room. 2. Testing of purity - (1)The purity of oxygen and hydrogen shall tested by a competent person at least once in every shift at the following posts:- (a) in the electrolysis room; (b) at the gas holder inlet; and (c) at the suction and of the compressor. (2) The purity figures shall be entered in a register and signed by the persons carrying out such test: Provided, however, that if the electrolysis plant is fitted with automatic recorder of purity of oxygen and hydrogen with alarm lights, it shall be sufficient if the purity of gases is tested at the suction and of the compressor only. 3. Restriction as to the compression - The oxygen and hydrogen gases shall not be compressed if their purity as determined under paragraph 2 above falls below 98% at any time. 4. Limit switch for gas holder - The bell of any gas holder shall not be permitted to go within the 30 centimetres of its lowest position when empty and a limit switch shall befitted to the gas holder in such a manner as to switch off the compressor motor when the limit is reached. 5. Provision of negative pressure switch - In addition to the limit switch in the gas holder, a sensitive negative pressure switch shall be provided in or adjacent to the suction main for hydrogen close to the gas holder and between the gas holder and the hydrogen compressor to switch off the compressor motor in the event of the gas holder being emptied to the extent as to cause vacuum. 6. Purity of caustic soda - The water and caustic soda used for making lye shall be chemically pure within pharmaceutical limits. 7. Precautions against reversal of polarity - Electrical connections at the electolyser cells and at the electric generator terminals shall be so constructed as to preclude the possibility of wrong connections leading to the reversal of polarity and in addition an automatic device shall be provided to cut off power in the event of reversal of polarity owing to wrong connections either at the switch board or at the electric generator terminals. 8. Colouring of gas pipes - Oxygen and hydrogen gas pipes shall be painted with distinguishing colours and in the event of leakage at the joints of the hydrogen gas pipe, the pipe after reconnection shall be purged of all air before drawing in hydrogen gas. 9. Use of flameproof fittings - All electrical wiring and apparatus in the electrolyser room shall be of flameproof construction or enclosed in flameproof fittings and no naked light or flame shall be allowed to be taken either in the electrolyser room or where compression and filling of the gases is carried on and such warning notices shall be exhibited in prominent places. 10. Prohibition of hot work - No part of the electrolyser plant and the gas holders and compressor shall be subjected to welding, brazing, soldering or cutting until steps have been taken to remove any explosive substance from that part and render the part safe for such operations and after the completion of such operations no explosive substance shall be allowed to enter that part until the metal has cooled sufficiently to prevent risk of explosion. 11. Repair, etc. to be done under supervision - No work or operations, repair or maintenance shall be undertaken except under the direct supervision of a person who, by his training, experience and knowledge of the necessary precautions against risk of explosion is competent to supervise such work. No electric generator after erection or repairs shall be switched on/the electrolysers unless the same is certified by the competent persons under whose direct supervision erection or repairs are carried on to be in a safe condition and the terminals have been checked for the polarity as required by paragraph 7. 12. checking of plant - Every part of the electrolysis plant and the gas holders and compressor shall have a regular schedule of overhaul and checking and every defect noticed shall be rectified forthwith. Schedule – XIV Manipulation of stone or any other material containing free silica 1. Application - This schedule shall apply to all factories or parts of factories in which manipulation of stone or any other material containing free silica is carried on. 2. Definitions- For the purpose of this Schedule - (a) “manipulation” means crushing, breaking, chipping, dressing, grinding, sieving, mixing, grading or handling of stone or any other material containing free silica or any other operation involving such stone or material; (b) “Stone or any other material containing free silica” means a stone or any other solid material containing not less than 5% by weight of free silica. 3. Precautions in manipulation- No manipulation shall be carried out in a factory or part of a factory unless one or more of the following measures, namely - (a) damping the stone or other material being processed, (b) providing water spray, (c) enclosing the process, (d) isolating the process, and (e) providing localised exhaust ventilation are adopted so as to effectively control the dust in any place in the factory where any person is employed, at a level equal to or below the maximum permissible level for silica dust as laid down in Table 2 appended to Rule 120. Provided that such measures as above said are not necessary if the process or operation itself is such that the level of dust created and prevailing does not exceed the permissible level referred to. 4. Maintenance of floors- (1) All floors or places where fine dust is likely to settle on and whereon any person has to work or pass shall be of impervious material and maintained in such condition that they can be thoroughly cleaned by a moist method or any other method which would prevent dust being airborne in the process of cleaning. (2) The surface of every floor of every work room or place where any work is carried on or where any person has to pass during the course of his work, shall be cleansed of dust once at least during each shift after being sprayed with water or by any other suitable method so as to prevent dust being airborne in the process of cleaning. 5. Prohibition relating young persons- No young person shall be employed or permitted to work in any of the operations involving manipulation or at any place where such operations are carried out. 6. Medical Facilities and records of examinations and tests - (1) The occupier of every factory to which the schedule applies, shall – (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause(1). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 7. Medical examination by Certifying Surgeon - (1) Every worker employed in the processes specified in paragraph 1, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such medical examination shall include tests for lead in urine and blood. ALA in urine, haemoglobin content, stippling of cells and steadiness test. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every twelve months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub- paragraph (1) except chest X-ray which will be once in 3 years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said process on the ground that continuance therein would involve special danger to the health of the worker he shall make a record of his findings in the said Certificate and the health register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he fully is incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 8. Exemptions - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or in frequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Schedule – XV Handling and processing of Asbestos, manufacture of any article of Asbestos and any other process of manufacture or otherwise in which Asbestos is used in any form. 1. Application - This schedule shall apply to all factories or parts of factories in which any of the following processes is carried on :- (a) breaking, crushing, disintegrating, opening, grinding, mixing or sieving of asbestos and any other processes involving handling and manipulation of asbestos incidental thereto; (b) all processes in the manufacture of asbestos textiles including preparatory and finishing processes; (c) making of insulation slabs or sections, composed wholly or partly of asbestos, and processes incidental thereto; (d) making or repairing of insulating mattresses, composed wholly or partly of asbestos, and processes incidental thereto; (e) manufacture of asbestos cardboard and paper; (f) manufacture of asbestos cement goods; (g) application of asbestos by spray method; (h) sawing, grinding, turning, abrading and polishing in dry state of articles composed wholly or partly of asbestos; (i) cleaning of any room, vessel, chamber, fixture or appliance for the collection of asbestos dust; and (j) Any other processes in which asbestos dust is given off into the work environment. 2. Definition - For the purpose of this Schedule - (a) “asbestos” means any fibrous silicate mineral and any admixture containing actionlite, amosite, anthophyllite, dhrysotile, crocidolite, tremolite or any mixture thereof, whether crude, crushed or opened; (b) “asbestos textiles” means yarn or cloth composed of asbestos or asbestos mixed with any other material; (c) “approved” means approved for the time being in writing by the Chief Inspector; (d) “breathing apparatus” means a helmet or face piece with necessary connection by means of which a person using it breathes air free from dust, or any other approved apparatus; (e) “Efficient exhaust draught” means a localised ventilation by mechanical means for the removal of dust so as to prevent dust from escaping into air of any place in which work is carried on. No draught shall be deemed to be efficient which fails to control dust produced at the point where such dust originates; (f) “preparing” means crushing, disintegrating, and any other processes in or incidental to the opening of asbestos; (g) “Protective clothing” means overalls and head covering, which (in either case) will when worn exclude asbestos dust. 3. Tools and equipment - Any tools or equipment used in processes to which this schedule applies shall be such that they do not create asbestos dust above the permissible limit or are equipped with efficient exhaust draught. 4. Exhaust draught - (1) An efficient exhaust draught shall be provided and maintained to control dust from the following processes and machines : (a) manufacture and conveying machinery namely - (i) preparing, grinding, or dry mixing machines; (ii) carding, card waste and ring spinning machines, and looms; (iii) machines or other plant fed with asbestos; (iv) machines used for the sawing, grinding, turning, drilling, abrading or polishing; in the dry state, of articles composed wholly or partly of asbestos; (b) cleaning, and grinding of the cylinders or other parts of a carding machine; (c) chambers, hoppers or other structures into which loose asbestos is delivered or passes; (d) work-benches for asbestos waste sorting or for other manipulation or asbestos by hand; (e) workplaces at which the filling or emptying of sacks, skips or other portable containers, weighing or other process incidental thereto which is effected by hand, is carried on; (f) sack cleaning machines; (g) mixing and blending of asbestos by hand; and (h) any other process in which dust is given off into the work environment. (2) Exhaust ventilation equipment provided in accordance with sub-paragraph (1) shall, while any work of maintenance or repair to the machinery, apparatus or other plant or equipment in connection with which it is provided is being carried on, be kept in use so as to produce an exhaust draught which prevents the entry of asbestos dust into the air of any work place. (3) Arrangements shall be made to prevent asbestos dust discharged from exhaust apparatus being drawn into the air of any workroom. (4) The asbestos bearing dust removed from any workroom by the exhaust system shall be collected in suitable recepticles or filter bags which shall be isolated from all work areas. 5. Testing and examination of ventilating systems - (1) All ventilating systems used for the purpose of extracting or suppressing dust as required by this schedule shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examinations or test shall be rectified forthwith. (2) A register containing particulars of such examination and tests and the state of the plant and the repairs or alternations (if any) found to be necessary shall be kept and shall be available for inspection by an Inspector. 6. Segregation in case of certain process - Mixing or blending of asbestos by the hand, or making or repairing of insulating mattresses composed wholly or partly of asbestos shall not be carried on in any room in which any other work is done. 7. Storage and distribution of loose asbestos – All loose asbestos shall while not in use be kept in suitable closed receptacles which prevent the escape of asbestos dust threrefrom and such asbestos shall not be distributed in the factory except in such receptacles or in totally enclosed system of conveyance. 8. Asbestos sacks (1) All sacks used as receptacles for the purpose of transport of asbestos within the factory shall be constructed of impermeable materials and shall be kept in good repair. (2) A sack which has contained asbestos shall not be cleaned by hand beating but by a machine, complying with paragraph 4. 9. Maintenance of floors and workplaces - (1) In every room in which any of the requirements of this schedule apply – (a) the floors, work-benches, machinery and plant shall be kept in a clean state and free from asbestos debris and suitable arrangements shall be made for the storage of asbestos not immediately required for use; and (b) the floors shall be kept free from any materials, plant or other articles not immediately required for the work carried on in the room, which would construct the proper cleaning of the floor. (2) The cleaning as mentioned in sub-rule (1) shall so for as is practicable, as carried out by means of vacuum cleaning equipment so designed and constructed and so used that asbestos dust neither escapes nor is discharged into the air of any work place. (3) When the cleaning is done by any method other than that mentioned in sub- paragraph (2), the persons doing cleaning work and any other person employed in that room shall be provided with respiratory protective equipment and protective clothing. (4) The vacuum cleaning equipment used in accordance with provisions of sub- paragraph (2), shall be properly maintained and after each cleaning operation, its surfaces kept in a clean state and free from asbestos waste and dust. (5) Asbestos waste shall not be permitted to remain on the floors or other surfaces at the work place at the end of the working shift and shall be transferred without delay to suitable receptacles. Any spillage of asbestos waste occurring during the course of the work at any time shall be removed and transferred to the receptacles maintained for the purpose without delay. 10. Breathing apparatus and protective clothing - (1) An approved breathing apparatus and protective clothing shall be provided and maintained in good conditions for use of every person employed - (a) in chambers containing loose asbestos; (b) in cleaning, dust settling or filtering chambers of apparatus; (c) in cleaning the cylinders, including the defer cylinders, or other parts of a carding machine by means of hand-strikes; (d) in filling, beating , or levelling in the manufacture or repair of insulating mattresses; and (e) in any other operation or circumstances in which it is impracticable to adopt technical means to control asbestos dust in the work environment within the permissible limit. (2) Suitable accommodation in conveniently accessible position shall be provided for the use of persons when putting on or taking off breathing apparatus and protective clothing provided in accordance with this rule and for the storage of such apparatus and clothing when not in use. (3) All breathing apparatus and protective clothing Washing not in use shall be stored in the accommodation provided in accordance with sub-rule (2) above. (4) All protective clothing in use shall be de-dusted under an efficient exhaust draught or by vacuum cleaning and shall be washed at suitable intervals. The cleaning schedule and procedure should be such as to ensure the efficiency in protective the wearer. (5) All breathing apparatus shall be cleaned and disinfected at suitable intervals and thoroughly inspected once every month by a responsible person. (6) A record of the cleaning and maintenance and of the condition of the breathing apparatus shall be maintained in a register provided for that purpose which shall be readily available for inspection by an Inspector. (7) No person shall be employed to perform any work specified in sub-paragraph (1) for which breathing apparatus is necessary to be provided under that sub-paragraph unless he has been fully instructed in the proper use of that equipment. (8) No breathing apparatus provided in pursuance of sub-paragraph (1) which has been worn by a person shall be worn by another person unless it has been thoroughly cleaned and disinfected since last being worn and the person has been fully instructed in the proper use of that equipment. 11. Separate accommodation for personal clothing - A separate accommodation shall be provided in a conveniently accessible position for all persons employed in operation to which this schedule applies for storing of personal clothing. This should be separated from the accommodation provided under sub-paragraph (2) of paragraph 10 to prevent contamination of personal clothing. 12. Washing and bathing facilities – (1) There shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the processes covered by the schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 15 persons employed. (2) The washing places shall have standpipes place at intervals of not less than one metre. (3) Not less than one half of the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable material shall be provided: Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 13. Mess room - (1) There shall be provided and maintained for the use of all worker employed in the factory covered by this schedule, remaining on the premises during the rest intervals, a suitable mess room which shall be furnished with:- (a) sufficient tables and benches with back rest, and (b) adequate means for warming food. (2) The mess room shall be placed under the charge of a responsible person and shall be kept clean. 14. Prohibition of employment of young persons - No young person shall be employed in any of the process covered by this schedule. 15. Prohibition relating to smoking - No person shall smoke in any area where processes covered by this schedule are carried on. A notice in the language understood by majority of the workers shall be posted in the plant prohibiting smoking at such areas. 16. Cautionary notices - (1) Cautionary notices shall be displayed at the approaches and along the perimeter of every asbestos processing area to warn all persons regarding - (a) hazards to health from asbestos dust, (b) need to use appropriate protective equipment, (c) Prohibition of entry to unauthorised persons, or authorised persons but without protective equipment. (2) Such notices shall be in the language understood by the majority of the workers. 17. Air monitoring - To ensure the effectiveness of the control measures, monitoring of asbestos fibre in air shall be carried out once at least in every shift and the record of the results so obtained shall be entered in a register specially maintained for the purpose. 18. Medical facilities and records of medical examinations and tests - (1) The occupier of every factory or part of the factory to which the schedule applied, shall- (a) employ a qualified medical practitioner for medical surveillance of the workers covered by this schedule whose employment shall be subject to the approval of the Chief Inspector of Factories; (b) Provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause(a). (2) The record of medical examinations and appropriated tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspectors. 19. Medical examination by Certifying Surgeon - (1) Every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function test, tests for detecting asbestos fibers in sputum and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the process referred to sub-paragraph (1) shall be re- examined by a Certifying Surgeon at least once in every twelve calendar months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests specified in sub-paragraph (1) except chest X-ray which will be carried out once in 3 years. (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the certificate and the certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (4) The certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after future examination, again certifies him fit for employment in these processes. 20. Exemptions - If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. Schedule – XVI Handling or manipulation of corrosive substances 1. Definitions - For the purposes of this schedule - (a) “corrosive operation” means an operation of manufacturing, storing, handling processing, packing, or using any corrosive substance in a factory; and (b) “corrosive substance” includes sulphuric acid, nitric acid, hydrochloric acid, hydrofluoric acid, carbolic acid, phosphoric acid, liquid chlorine, liquid bromine, ammonia, sodium hydroxide and potassium hydroxide and a mixture thereof, and any other substance which the State Government by notification in the Official Gazette specify to be corrosive substance. 2. Flooring - The floor of every workroom of a factory in which corrosive operation is carried on shall be made of impervious, corrosion and fire resistance material and shall be so constructed as to prevent collection of any corrosive substance. The surface of such flooring shall be smooth and cleaned as often as necessary and maintained in a sound condition. 3. Protective equipment- (a) the occupier shall provide for the use of all persons employed in any corrosive operation suitable protective wear for hands and feet, suitable aprons, face shields, chemical safety goggles, and respirators. The equipment shall be maintained in good order and shall be kept in clean and hygienic condition by suitably treating to get rid of the ill effects of any absorbed chemicals and by disinfecting. The occupier shall also provide suitable protective creams and other preparations wherever necessary. (b) The Protective equipment and preparations provided shall be used by the persons employed in any corrosive operation. 4. Water facilities - Where any corrosive operation is carried on, there shall be provided as close to the place of such operation as possible, a source of clean water at a height of 210 centimetres from a pipe of 1.25 centimetres diameter and fitted with a quick acting valve so that in case of injury to the worker by any corrosive substance, the injured part can be thoroughly flooded with water. Whenever necessary, in order to ensure continuous water supply, a storage tank having a minimum length, breadth and height of 210 centimetres, 120 centimetres and 60 centimetres respectively or such dimensions as are approved by the chief inspector shall provided as the source of clean water. 5. Cautionary notice - A cautionary notice in the following form and printed in the language which majority of the workers employed understand, shall be displayed prominently close to the place where a corrosive operation is carried out and where any of the operation mentioned in clause 2 above is carried out and where it can be easily and conveniently read by the workers. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so displayed. CAUTIONARY NOTICE DANGER Corrosive substances cause severe burns and vapours thereof may be extremely hazardous. In case of contact, immediately flood the part affected with plenty of water for at least 15 minutes. Get medical attention quickly. ---------------------------------------------------------------------------------------------------------------- 6. Transport - (1) Corrosive substances shall not be filled, moved or carried except in containers or through pipes and when they are to be transported in containers, they shall be placed in crates of sound construction and of sufficient strength. (2) A container with a capacity of 11.5 litres or more of a corrosive substance shall be placed in a receptacle or crate and then carried by more than one person at a height below the waist line unless a suitable rubber wheeled truck is used for the purpose. (3) Containers for corrosive substances shall be plainly labelled. 7. Devices for handling corrosive - (1) Tilting, lifting of pumping arrangements shall be used for emptying jars, carboys and other containers of corrosives. (2) Corrosive substance shall not be handled by bare hands but by means of a suitable scoop or other device. 8. Opening of valves - Valves fitted to containers holding a corrosive substance shall be opened with great care. If they do not work freely, they shall not be forced open. They shall be opened by a worker suitably trained for the purpose. 9. Cleaning tanks, stills, etc. - (1) In cleaning out or removing residues from stills or other large chambers used for holding any corrosive substance, suitable implements made of wood or other material shall be used to prevent production of arseniuretted hydrogen (arsine). (2) Whenever it is necessary for the purpose of cleaning or other maintenance work for any worker to enter chamber, tank, vat, pit or other confined space where a corrosive substance had been stored, all possible precautions required under section 36 of the Act shall be taken to ensure the worker’s safety. (3) Wherever possible, before repairs are undertaken to any part of equipment in which a corrosive substance was handled, such equipment or part thereof shall be freed of any adhering corrosive substance by adopting suitable methods. 10. Storage - (1) Corrosive substances shall not be stored in the same room with other chemicals, such as turpentine, carbides, metallic powders and combustible materials, the accidental mixing with which may cause a reaction which is either violent or gives rise to toxic fumes and gases. (2) Pumping or filling overhead tanks, receptacles, vats or other containers for storing corrosive substances shall be so arranged that there is no possibility of any corrosive substance overflowing and causing injury to any person. (3) Every container having a capacity of twenty litres or more and every pipeline, valve, and fitting used for storing or carrying corrosive substances shall be thoroughly examined every year for finding out any defects, and defects so found out shall be removed forthwith. A register shall be maintained of every such examination made and shall be produced before the Inspector whenever required. 11. Fire extinguishers and fire fighting equipment - An adequate number of suitable types of fire extinguishers or other stored, shall be provided. Such extinguishers or other equipment shall be regularly tested and refilled. Clear instructions as to how the extinguishers or other equipment should be used, printed in the language which majority of the workers employed understand, shall be affixed near each extinguisher or other equipment. 12. Exemption - If in respect of any factory on application made by the manager, the Chief Inspector is satisfied that owing to the exceptional circumstances, or the infrequency of the process or for any other reason to be recorded by him in writing, all or any of the provisions of this schedule are not necessary for the protection of the persons employed therein, he may by a certificate in writing, which he may at any time revoke, exempt the factory from such of the provisions and subject to such conditions as he may specify therein. Schedule – XVII Use of ovens and driers in factories 1. Application- this schedule shall apply to ovens and driers, except those used in laboratories and kitchens of any establishment and those which have a capacity below 325 liters. 2. Definitions- for the purpose of this schedule, oven or drier means any enclosed structure,receptacle,compartment or box which is used for baking, drying or other wise processing of any article or substance at a temperature higher than that ambient temperature of air in the room of space in which the oven or drier is situated, and in which the flammable or explosive mixture of air and flammable substance is likely to be evolved with the enclosed structure ,receptacle, compartment or box or part there of on account of article or substance which is baked or dried or otherwise processed within it. 3. Separate electric connection- Electric power supplied to every oven or drier shall be by means of separate circuit provided with an isolated switch. 4. Design,construction,examination and testing- (a) every oven or drier shall be properly designed on sound engineering practice and be of good construction, sound materials and adequate strength free from any patent defect and safe, if properly used. (b) no oven or drier shall be taken into use in factory for the first time unless a competent person has thoroughly examined all its parts carried out the tests as are required to establish that the necessary safe systems and control provided for safety in operation for the processes for which it is to be used and a certificate of such examination and tests signed by that competent person has been obtained and are kept available for inspection. © all parts of an oven or drier has undergone any alteration or repair which has the effect of modifying any of the design characteristics, shall not be used unless a thorough examination and tests as have been mentioned in clause (b) have been carried by the competent person and a certificate of such examination and tests signed by that competent person has been obtained and are kept available for inspection. 5. Safety, Ventilation- (a) every oven or drier shall be provided with a positive and effective safety ventilation system using one or more motor driven centrifugal fans so as to dilute any mixture of air and flammable substance that may be formed within the oven or drier and maintain the concentration of the flammable substance in the air at safe level of dilution. (b) The safe level of dilution referred to in clause (a) shall be so as to achieve a concentration of concerned flammable material in air of not more than 25 % of its lower explosive limit; Provided that level of concentration in the air up to 50% of the lower explosive limit of the concerned flammable substance may be permitted to exist subject to installation and maintenance of an automatic device which:- (I) Shows continuously the concentration of the flammable substance in air present in the oven or drier at any instant; (II) Sounds an alarm when the concentration of the flammable substance in air present in any part of oven or drier reaches a level of 50% of explosive limit (III) Shuts down the heating system of the oven or drier automatically when the concentration of the flammable substance in air present in any part of oven or drier reaches a level of 60% of lower explosive limit © No oven or drier shall be operated without its safety ventilation system working in efficient manner. (d) no oven or drier shall be operated with a llevel of dilution less than what is referred in clause (b) (e) exhaust ducts of safety ventilation system should be so designed and placed that their ducts discharge the mixture of air and flammable substance away from the work room and not near windows or doors or other openings from where the mixture could re- enter the work room. (f) The fresh air admitted into the oven or drier by means of safety ventilation system shall be circulated adequately by means of circulating fans or fans through all parts of the oven or drier so as to ensure that their are no location where the flammable substance can accumulate in the air become pocketed to any dangerous degree. (g) Throttling dampers in any safety ventilation system should be so designed by cutting away the portion of damper or otherwise that system will handle at least the minimum ventilation rate required for safety when they are set in their maximum throttling position. 6. Explosion panels – (a) every oven or drier having an internal total space of not less than half cubic meter shall be provided with suitably design explosion panel so as to allow the release of the pressure of any possible explosion within the oven or drier through explosions vents. The area of opening of any access doors which are provided with suitable arrangements for there release in case of an explosion shall not be less than 2200 sq cm for every 1 cu m of the volume of the oven or drier. The design of the explosion panel and doors as stated above shall be such as to secure there complete release under an internal pressure of 0.25 kg/sq cm . (b) The explosion releasing panel shall, as far as practicable, be situated on the roof of the oven or drier or at those portions of the walls where persons don’t remain in connection with operation of oven or drier. 7. Inter locking arrangement – In each oven or drier efficient inter locking arrangement shall be provided and maintain to insure that (a) All ventilating fans and circulating fans whose failure would adversely effect the ventilation rate of flow pattern, are in operation before any mechanical conveyor that may be provided for feeding the article or substances to be processed in the oven or drier, input into operation (b) Failure of any of the ventilating or circulating fans will automatically stop any conveyor as referred to in clause (a) as may be provided as well as so the fume supply by closing the shut of valve and shut off the ignition in the case of gas or oil fired ovens and in case of electrically heated oven switch off the electrical supply to the heater (c) The afore said mechanical conveyor is set in operation before the said shut off valve can be energies (d) The failure of the aforesaid conveyor will automatically closed the said shut off valve in the case of oven and drier heated by gas , oil or steam and deactivate the ignition system or cut off the electrical heater in the case of electrically heated ovens are furnaces 8. Automatic ventilation; - Every oven or drier heated by oil, gas, steam or electricity shall be provided with an efficient arrangement for automatic ventilation consisting of at least three volume changes with fresh air by operation of safety ventilation fans and circulating fans so as to effect purging of the oven or drier of any mixture of air and flammable substance before the heating system can be activated and before the conveyor can be placed in position. 9. Temperature control – Every oven or drier shall be provided with an automatic arrangement to ensure that the temperature which does not exceed a maximum temperature required in respect of the particular process is being carried out 10. Multi stage processes – What ever material are to be processed in ovens or driers in successive operation suitable arrangements should be provided to ensure that the operating temperature necessary for safe operation at each stage are maintain within the design limit 11. Combustible substances not to drip on electrical heater or burner flame – Effecting arrangement shall be provided in every oven or drier to prevent dripping of combustible substances on electrical heater or burner flame used for heating. 12. Periodical examination, testing and maintenance – (a) All parts of every oven or drier shall be properly maintain and thoroughly examined and the various control as mentioned in the schedule and the working of the oven or drier shall be tested at frequent interval to ensure its safe operation by a responsible person authorized by the occupier or manager in this behalf who by his experience and knowledge of necessary precaution against risk of explosion, is fit to undertake such work (b) A register shall be maintained in which the details of various tests carried out from time to time under clause (a) shall be entered and every entry shall be signed by the person making the test. 13: - Training of operator – No person shall be assigned any task connected with operation of any oven or drier unless his has completed 18 yrs of a and is properly trained 14. Polymerizing machine – (a) Printed fabric shall be thoroughly dried by passing them over drying canes or through hot flue or other equally effecting means before the same is allowed to pass through polymerizing machines (b) Infra ray heater of polymerizing machines shall be cut off while running the print Schedule – XVIII Manufacture or manipulation of carcinogenic dye intermediates 1. Application - The schedule shall apply in respect of all factories or any part thereof where processes in which the process of manufacturing or manipulation of a carcinogenic Dye Intermediates (here in referred to as the said manufacturing processes) is carried on. Provided that Paragraphs 25 and 26 shall only to the a process involving manufacturing, manipulation of compounds mentioned in Appendix B ( here in referred to as the said manufacturing processes B) PART-I 1. Definition – (a) For the purpose of this schedule a nitro or amino compounds means a nitrated or aminated compound of aromatic hydrocarbons mentioned in Appendix A or B attached there to. (b) “Approved “means approved by Chief Inspector. (c) “Omitted” (d) “efficient exhaust draught” means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fume so as to prevent them from escaping into the air of any place in which work is carried on. No draught, shall be deemed to be efficient which fails to remove smoke generated at the point where such gas, vapour, fume or dust originates; and (e) Manipulation shall include mixing, blending, filling, emptying, grinding, sieving, drying, packing, sweeping, handling, using or chemical processing of a nitro-amino compound. (f) “Air line respirator” means a helmet or face piece with necessary connections by means of which a person using it in a poisonous or irritatant atmosphere breathes ordinary air or any suitable apparatus approved in writing by Chief Inspector. 3. Cautionary placards - Cautionary placards in the form specified in appendix attached to this schedule and printed in the language of the majority of the workers employed in the said processes shall be affixed in prominent places frequented by them in the factory, where the placards can be conveniently read. Arrangements shall be made by the manager to instruct periodically all such workers regarding the precautions contained in the cautionary placards. 4. Prohibition relating to employment of women and young persons - No woman or young person shall be employed or permitted to work in any room in which the said processes are carried on. 5. Air space- in every room in which the said manufacturing process is carried on there shall at least 15 cubic-meters of air space excluding any space occupied by machinery equipments or any other article for each person employed there in and in computing this air space no height over 4.25 meters shall be taken into account. 6. Efficient exhaught draught- unless the said process is completely enclosed so as to not to give rise to dust or fume it shall not be carried on without the use of an efficient exhaught draught when a nitro oa amino compound; (a) Is introduced into a tank, hopper, machine, or container or filled into cartridge;or (b) Is ground, crushed, mixed, sieved,or blended. 7. Floors of workroom - The floor of every workroom in which the said processes are carried on shall be (a) Smooth and impervious to water provided that asphalt or tar shall not be used in the composition of the floor, (b) Maintained in a state of good repair, (c) With a suitable slope for easy draining and provided with gutters and (d) Thoroughly washed daily with the drain water being led into a sewer through a closed channel. 8. Work benches- work benches on which a nitro or amino compound is manipulated shall- (a) Have a smooth impervious surface preferably of stainless steel; and (b) Be washed daily with hose-pipe or cleaned by means of suction cleaning apparatus at the time when no other work is carried on there at. 9. Waste disposal - (1) There shall be provided a suitable receptacle made of non-absorbable material with a tightly fitting cover for depositing waste material like cloth paper or other material soiled with a nitro or amino compound. (2) Such receptacle shall be destroyed by burning or using other suitable methods under the supervision of a responsible person. 10. Disposal of empty containers - Empty containers used for holding compounds included under Appendix_A shall be thoroughly cleaned of their contents and treated with an inactivating agent before being discarded. 11. Decontamination of Pits, Tanks etc.- (a) before a worker enters a pit,tank,kettle or any other confined space which contains a nitro or amino copmpound it shall be thoroughly washed and cleaned. (b) No part of the plant which contains nitro or amino compounds shall be repaired or opened for repairs unless it has been emptied of such compounds and thoroughly cleaned & decontaminated. © Records of such treatments shall be maintained in a register approved by the Chief Inspector and the register shall be made available for inspection when required by Inspector. 12. Manual handling - Controlled substances shall not be allowed to be mixed, filled, emptied or handled except by means of a scoop with a handle. Such scoop shall be thoroughly cleaned daily 13 Protective wears- the occupier shall provide, maintain clean and in good condition protective clothing and other equipments as specified in the table below:- TABLE Process Protective clothing and other equipments For manipulation of compounds Mentioned in Appendix-A (A) Long trousers and shirts or overalls with full sleeves and head coverings. The shirt or overall shall cover the neck completely; and (B) rubber hand gloves, rubber aprons, rubber gum boots and airline For manipulation of compounds Mentioned in Appendix-B (A) White clean clothing mentioned in (A) as above in addition to white clean shirts. Singlet and protective equipments as mentioned in (B) above (B) White long sleeve apron 14. Instructions regarding risk - Every worker on his first employment in the said processes shall be fully instructed on the properties of the toxic chemicals to which he is likely to be exposed to, of the dangers involved and the precautions to be taken. Workers shall also be instructed on the measures to be taken to deal with an emergency. 15. Medical facilities and records of examinations and tests - (1) the occupier of every factory to which this schedule applies, shall - (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) Provide to the medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of such examinations carried out by the medical practitioner shall be maintained in a separate, register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 16. Medical examination by certifying Surgeon - (1) every worker employed in the processes specified in paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examinations shall include skin test for dermatitis and no worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in a manganese process shall be re-examined by a Certifying Surgeon at least once in every three calendar months and such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 32. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manger of the factory. The record of each examination carried out under sub-paragraph (1) and (2), including the nature and the results of this test, shall also be entered by the Certifying Surgeon in a health register in

Previous and next

All provisions of Punjab Factories Rules 1952

Questions people ask

Is form D of Punjab Factories Rules 1952 still in force?

No repeal of Punjab Factories Rules 1952 is recorded.