LawGrids logoLAWGRIDS.ORG

Rule 53, Rajasthan Factories Rules,1951: Further safety precautions

Rajasthan Factories Rules,1951 - Rule 53

Text of rule 53

Further safety precautions

53. Further safety precautions. — (1) Without prejudice to the provisions of sub-section (1) of section 21 in regard to the fencing of machines, the further precautions specified in the Schedules annexed hereto shall apply to the machines noted in each Schedule. @[(2) The fencing and other devices for protection shall be so constructed and designed as to render it impossible for any person to pass between the fencing and a moving part of the machinery while it is in motion]. #[Schedule-I Textile Machinery except Machinery used in Jute Mills. 1. Application. — The requirement of this schedule shall apply to machinery in factories engaged in the manufacture processing of textiles other than Jute textiles. The schedule would not apply to machinery in factories engaged exclusively in the manufacture of synthetic fibres. 2. Definitions. — for the purposes of this schedule.— (a) "Calendar" means a set of heavy rollers mounted on vertical side frames and arranged to pass cloth between them. Calendars may have two to ten rollers or bowls. some of which can be heated. (b) "Embossing Calendar" means a calendar with two or more rolls, one of which is engraved for producing figure effects of various kinds on a fabric. (c) "Card" means a machine consisting of cylinders of various sizes-and in certain cases flats-covered with card clothing and set in relation to each so that fibres in staple form may be separated into individual relationship. The speed of the cylinders and their direction of rotation varies. The finished product Is delivered as a silver, Cards different types are the revolving flat card, the roller and clearer card, etc. (d) "Card Clothing" means the material with which the surfaces of the cylinder, defer, flats, etc. of a card are covered and consists of a thick foundation material made of, either textile fabrics through which are pressed many fine closely spaced, specially bent wires, or mounted saw toothed wire. (e) "Comber" means a machine for combine fibres of cotton, wool. etc. The essential parts are device for feeding forward a fringe of fibres at regular intervals and an arrangements of combs or pins, which at the right time pass through the fringe. All tangled fibres, short fibres and nips are removed and the long fibres are laid parallel. (f) "Combined machinery" means a general classification of machinery including cambers, silver lap machines, ribbon lap machines, and pillboxes, but excluding cards. (g) Rotary staple "Cutter" means a machine consisting of one or more rotary blades used for the purpose of cutting textile fibres into staple lengths. ------------------------------------------------------------------------------------------------------------------- @. Substituted vide Notification No. F1(112)L&E/76 dated 24.3.1979; Rajasthan Gazette Part IV-Ga(1). dated 26.4.1979 #. Deleted vide Notification No. F.4(3) Shram/88 dated 8.1.1991, published Rajasthan Gazette Part 3(Ga) dated Rajasthan 25.6.1992 (h) "Garnett machine" means any of a number of types of machines for opening hard twisted waste of wool, cotton, silk, etc. Essentially, such machines consist of a lickering one or more cylinders, each having a competent worker and stripper rolls, and a fancy roll and differ. The action of such machines is some-what like that a wool card, but it is much more severe in that the various rolls are covered with garnet wire instead of a card clothing. (i) "GiIl box" means a machine used in the worsted system of manufacturing yams. Its function is to arrange fibres in parallel order. Essentially, it consists of a pair of feed rolls and a series of followers where the followers move at a faster surface speed and perform a combing action." (j) "In-running rolls" means any pair of rolls or drums between which there is a "nip". (k) "Interlocking arrangement" means a device that prevent the setting in motion of a dangerous part of a machine or the machine itself while the guard cover or door provided to safeguard against danger is open or unlocked and which will also hold the guard, cover or door closed and locked while the machine or the dangerous part is in motion. (l) "Kier" means a large metal vat, usually a pressure type, in which fabrics may be boiled out, bleached, etc. (m) "Ribbon lapper" means a machine or a part of a machine used to prepare laps for feeding a cotton comb: its purpose is to provide a uniform lap in which the fibres have been strengthened as much as possible. (n) "Silver lapper" means a machine or a part of a machine in which a number of parallel card silvers are drafted slightly, laid side by side in a compact sheet and wound into a cylindrical package. (o) "Loom" means a machine for effecting the interlocking of two series of yarns crossing one another at right angles. The warp yarns are wound on a warp beam and pass through handles and reeds. The filling is shot across in a shuttle and settled in place by veeds and slay, and the fabric is wound on a cloth beam. (p) "Starch mangle" means a mangle that is used specifically for starching cotton goods. It commonly consists of two large rolls and a shallow open vat with several immersion rolls. The vat contains the starch solution. (q) "Water mangle" means a calendar having two or more rolls used for squeezing water from fabrics before drying. Water mangles also may be used in other ways during the finishing of various fabrics. (r) "Mule" means a type of spinning frame having a head stock and carriage as its two main sections. The head stock is stationary. The carriage is movable and it carries the spindles which draft and spin the roving into yarn. The carriage extends over the whole width of the machine and moves slowly towards and away from the head stock during the spinning operation. (s) "NIP" is the danger zone between two rolls or drums which by virtue of their positioning and movement create a nipping hazard. (t) "Openers and Pickers" means a general classification of machinery which includes breaker pickers intermediate pickers, finisher pickers, single process pickers, multiple process pickers, willow machines card and pickers waste cleaners. thread extractors, shredding machines, roving waste openers, shoddy pickers, blade, breakers, feeders, vertical opener, lattice cleaners, horizontal cleaners, and any similar machinery equipped with either cylinders screen section, calendar section, rolls, or beaters used for the preparation of stock for further processing. (u) "Paddler" means through for the solution and two or more squeeze rolls between which cloth passes after being passed through a mordant or dye bath. (v) "Plaiting machines" means a machine used to lay cloth into folds of regular length for convenience of subsequent process or use. (w) "Roller Printing Machine" means a machine consisting of a large central cylinder, or pressure bowl, around the lower part of the perimeter of which is placed a series of engraved colour rollers (each having a colour through) a furnishes rollers, doctor blades, etc. The machine is used for printing fabrics. (x) "Continuous bleaching range" means a machine for bleaching of cloth in rope of open-width form with the following arrangement. The cloth, after wetting out, pass through a squeeze roll into a saturator containing a solution of caustic soda and then to an enclosed J-lox. A V-shaped arrangement is attached to the front part of the J- Box for uniform and rapid saturation of the cloth with steam before it is packed down in the J-Box. The cloth, in a single strand rope form, passes over a guide roll down the first arm of the "V" and up the second. Steam is injected into the "V" at the upper end of the second arm so that the cloth is rapidly saturated with steam at this point. The J-Box capacity is such that cloth will remain hot for a sufficient time to complete the scoring action. It then passes a series of washers with a squeeze roll in between. The cloth then passes through a second set of saturator, J-Box and washer, where it is treated with the peroxide solution. By slight modification of the form of the unit, the same process can be applied to open-width cloth. (y) "Mercerizing range" means a 3 bowl mangle, a tenter frame, and a number of boxes for washing and scouring. The whole set up is in straight line and all parts operate continuously. The combination is used to saturate the cloth with sodium hydrozide, stretch it while saturated and washing out most of the caustic before releasing tension. (z) "Sanforizing-Machine" means a machine consisting of a large steam-heated cylinder, and endless, thick, woolen felt blanket which is in close contact with the cylinder for most of its perimeter, and an electrically heated shoe which presses the cloth against the blanket while the latter is in a stretched condition as it curves around feed-in roll. (aa) "Shearing-Machine" means a machine used for shearing cloth. Cutting action is provided by a number of steel blades spirally mounted on a roller. The roller rotates in close contact with a fixed ledger blade. There may be from one to six such rollers on a machine. (bb) "Singling machine" means a machine which comprises of a heated roller, plate, or an open gas flame. The cloth or yarn in rapidly passed over the roller or the plate or through the open gas flame to remove fuzz or hairiness by burning. (cc) "Slasher" means a machine used for applying a size mixture to wrap yarns. Essentially, it consists of a stand for holding section beams, a size box, one or more cylindrical dryers or an enclosed hot air dryer. and a beaming end for winding the yarn on the loom beams. (dd) "Tenter frame" means a machine for drying cloth under tension. It essentially consists of a pair of endless travelling chains fitted with clips of fine pins and carried on tracks. The cloth is firmly held at the selvages by the two chains which diverge as they move forward so that the cloth is brought to the desired width. (ee) "Warper" means a machine for preparing and arranging the yarns intended for the warp of a fabric, specifically, a beam warper. 3. General Safety requirements. — (1) Every textile machine shall be provided with individual mechanical or electrical means for starting and stopping such machines. Belt shifter on machines driven by belts and shafting should be provided with a belt shifter lock of an equivalent positive looking device. (2) Stopping and starting handles or other controls shall be of such design and so positioned as to prevent the operator's hand or fingers from striking against any moving part of any other part of the machine. (3) All belts, pulleys, gears, chains, sprocket wheels and other dangerous moving parts of machinery which either form part of the machinery or are used in association with it, shall be securely guarded. 4. Opener and pickers. — (1) In all opening or picker machinery, beaters and other dangerous parts shall be securely fenced by suitable guards so as to prevent contact with them. Such guards and doors or covers or openings giving access to any dangerous part of the machinery shall be provided with interlocking arrangement: Provided that in the case of doors or covers of openings giving access to any dangerous part, other than beater covers, instead of the interlocking arrangement, such opening may be so fenced by guards which prevent access to any such dangerous part and which is either kept positively locked in position or fixed in such manner that it cannot be removed without the use of hand tools. (2) The feed rolls on all opening and picking machinery shall be covered with a guard designed to prevent the operator from reaching the nip while the machinery is in operation. (3) The lap forming rollers shall be fitted with a guard or covers which shall prevent access to the nip at the in take of the lap roller and fluted roller as long as the weighted rack is down. The guard or cover shall be so locked that it cannot be raised until the machine is stopped and the machine cannot be started until the cover guard is closed: Provided that the foregoing provision shall not apply to the machine equipped with automatic lap forming devices: Provided further that any such machine equipped with an automatic lap forming device shall not be used unless the automatic lap forming device is in efficient working order. 5. Cotton Cards. — (1) All cylinder doors shall be secured by an interlocking arrangement which shall prevent the door being opened until the cylinder has ceased to revolve and shall render it impossible to restart the machine until the door has been closed: Provided that the latter equipment in respect of the automatic locking device shall not apply while stripping or grinding operations are carried out: Provided further that stripping or grinding operations shall be carried out only by specially trained adult workers wearing tight fitting clothing whose names have been recorded in the register prescribed in this behalf as required in sub-section (1) of Section 22. (2) The licker in shall be guarded so as to prevent access to the dangerous parts. (3) Every card shall be equipped with an arrangement that would enable the card cylinder to be driven by power during stripping/grinding operations without having to either shift the main belt to the fast pulley of the machine or to dismantle the interlocking mechanism. Such an arrangement shall be used only for stripping or grinding operations. 6. Garnet Machine. — (1) Garnet licker ins shall be enclosed. (2) Garnet fancy rolls shall be enclosed by guards. These shall be installed in a way that keeps worker rolls reasonably accessible for removal or adjustment. (3) The underside of the garnet shall be guarded by o screen mesh or other form of enclosures to prevent access. 7. Cill Boxes. — (1) The feed end shall be guarded so as to prevent fingers being caught in the pins of the intersecting falters. (2) All nips in-running rolls shall be guarded by suitable nip guards conforming to the following specifications. Any opening which the guard may permit when fitted in position shall be so restricted with respect to the distance of the opening from any nip point through that opening and in any circumstances the maximum width of the opening shall not exceed the following:— Distance of Opening room nip point Maximum width of Opening 0 to 38 mm 6mm 39 to 63 mm 10mm 64 to 88 mm 13mm 89 to 140 mm 15mm 141 to 165 mm 19mm 166 to 190 mm 22mm 191 to 215 mm 32mm 8. Silver and Ribbon Lapper (Cotton). — The Calendar drums and the lap spool shall be provided with a guard to prevent access to the nip between the in-running rolls: 9. Speed Frames. — Jack box wheels at the head stock shall be guarded and the guard shall have interlocking arrangement: 10. Spinning mules. — Wheel on spinning mule carriages shall be provided with substantial wheel guard, extending to within 6 mm of the rails: 11. Warpers. — Swivelled double-bar gates shall be installed on all warpers operating in excess of 410 meters/min. These gates shall have inter-locking arrangement, except for the purpose of inching or jogging: Provided that the top and bottom bars of the gate shall be at least 1.05 and 0.53 meters high from the floor or working platform, and the gate shall be located 38 mm from the vertical tangent to the beam head. 12. Slashers : Cylinder dryers. — (1) (a) All open nips of in-running rolls shall be guarded by nip guards conforming to the requirements in paragraph 7. (b) When slashers are operated by control levers these levers shall be connected to a horizontal bar or treadle located not more than 170 cm. above the floor to control the operation from any point. (c) Slashers operated by push button control shall have stop and start buttons located at each end of the machine, and additional buttons located on both sides of the machine at the size box and the delivery end. If calendar rolls are used additional buttons shall be provided at both sides of the machine at point near the nips except when slashers are equipped with an enclosed dryer as in paragraph (b). (2) Enclosed hot air dryer.— (a) All open nips of the top squeezing rollers shall be guarded by nip guard conforming to the requirements in paragraph 7(2). (b) When slashers are operated by control levers, these levers shall be connected to a horizontal bar or treadle located not more than 170 cm. above the floor to control the operation from any point. (c) Slashers operated by push-button control shall have stop and start buttons located at each end of the machine and additional stop and start buttons located on both sides of the machines at intervals spaced not more than 1.83 meters on centres. 13. Looms. — (1) Each loom shall be equipped with suitable guards designed to minimise the danger from flying shuttles. (2) Beam weights for tension in beam shall be of such construction so as to prevent it falling during its adjustment. 14. Valves of Biers, tanks, and other containers. — (1) Each valve controlling the flow of steam, injurious gases or liquids into a Icier or any other tank or container into which a person is likely to enter in connection with a process, operation, maintenance or for any other purpose, shall be provided with a suitable locking arrangement to enable the said person to lock the valve securely in the closed position and retain the Key with him before entering the kier. tank or container. (2) Wherever boiling tanks, caustic tanks and any other containers from which liquids which are hot. corrosive or toxic may over flow or speash, are so located that the operator can not see the contents from the floor or working area emergency shut off valves which can be controlled from a point not subject to danger of splash shall be provided to prevent danger. 15. Shearing machines. — All revolving blades on shearing machines shall be guarded so that the opening between the cloth surface and the bottom of the guard will not exceed 10 mm. 16. Continuous bleaching range (cotton and rayon). — The nip of all in-running rolls of open-with bleaching machine rolls shall be protected with a guard to prevent the workers from being caught at the nip. The guard shall extend across the entire length of the nip. 17. Mercerizing range (piece goods). — (1) A stopping device shall be provided at each end of the machine. (2) A guard shall be provided at each end of the frame between the in-running chain and the clip opener. (3) A nip guard shall be provided for in-running rolls, of the mangle and washers and the guard shall conform to the requirements in paragraph 7 (2). 18. Tendet frames. — (1) A stopping device shall be provided at each end of the machine. (2) A guard shall be provided at each end of the machine frame at the in-running chain and clip opener. 19. Peddlers. — Suitable nip guards conforming to the requirement in paragraph 7(2) shall be provided to all dangerous running rolls. 20. Centrifugal extractors. — (1) Each extractor shall be provided with a guard for the basket, and the guard shall have interlocking arrangement. (2) Each extractor shall be equipped with a mechanically or electrically operated brake to quickly stop the basket when the power driving the basket is shut off. 21. Squeezer of wringer extractor, water mangle, starch mangle, back washer (worsted yarn) crabbing machine, and decating machines. All in-running rolls shall be guarded with nip guards conforming to the requirements in paragraph 7(2). 22. Sanforizing and Polymer machine. — (1) NIP guard shall be provided on all accessible in running rolls and these shall conform to the requirements in paragraph 7(2). (2) Access from the sides to the nips of in-running rolls should be fenced by suitable side guards. (3) A safety trip rod, cable or wire centre cord shall be provided across the front and back of all polymer cylinders. extending the length of the face of the cylinder. It shall operate readily whether pushed or pulled. The safety trip shall not be more than 170 cm. above the level at which the operator stands and shall be readily accessible. 23. Rope Washers. — (1) Splash guards shall be installed on all rope washers unless the machine is so designed as to prevent the water or liquid from splashing the operator, the floor or working surface. (2) A safety trip rod, cable or wire centre cord shall be provided across the front and back of all rope washers extending the length of the face of the washer. It shall operate readily whether pushed or pulled. This safety trip shall not be more than 170 cm. above the level on which the operator stands and shall be readily accessible. 24. Laundry washer tumbler or shaker. — (1) Each drying tumbler, each double cylinder shaker or clothes tumbler and each washing machine shall be equipped with an interlocking arrangement which will prevent the power operation of the inside cylinder when the outer door on the case or shell is open, and which will also prevent the outer door on the case or shell from being open without shutting of the power and the cylinder coming to a stop. This should not prevent the movement of the inner cylinder by means of a hand operated mechanism or an inching device. (2) Each closed barrel also be equipped with adequate means for holding open the door or covers of the inner and outer cylinders or shells while it is being loaded or unloaded. 25. Printing machine (roller type). — (1) All in running rolls shall be guarded by nip guards conforming to the requirement in paragraph 7(2) (2) The engraved roller gears and the large crown shell shall be guarded. 26. Calendars. — The nip at the in-running side of the rolls shall be provided with a guard extending across the entire length of the nip and arranged to prevent the fingers of the workers from being pulled in between the rolls or between the guard and the rolls, and so constructed that the cloth can be fed into the rolls safely. 27. Rotary staple cutters. — The cutter shall be protected by a guard to prevent hands reaching the cutting zone. 28. Plaiting machines. — Access to the trap between the knife and card bar shall be prevented by guard. 29. Hand baling machine. — An angle iron handle-stop guard shall be installed at right angle to the frame of the machine. The stop guard shall be so designed and so located that it will prevent the handle from travelling beyond the vertical position should be handle slip from the operator's hand when the pawl has been released from the teeth of the take-up gear. 30. Flat work ironer. — Each flat work or collar ironer shall be equipped with a safety bar or other guard across the entire front of the feed of first pressure rolls, so arranged that the striking of the bar or guard by the hand of the operator or other person will stop the machine. The guard shall be such that the operator or other person cannot reach into the rolls without removing the guard. This may be either a vertical guard on all sides or a complete cover. If a vertical guard is used, the distance from the floor or working platform to the top of guard shall be not less than 1.83 meters.] Schedule II (Cotton Ginning and Pressing) 1. Line Shaft. — The line shaft or second motion in cotton ginning factories, when below floor level, shall be completely enclosed by a continuous wall or unclimbable fencing with only so many openings as are necessary for access to the shaft for removing cotton seed, cleaning and oiling, and such openings shall be provided with gates or doors which shall be kept closed and locked. 2. Gin-house. — No person other than the gin-feeder shall be per-mitted to clean cotton on or in the Proximity of a gin-roller where the machine of which it is a part is in motion under power. 3. Press-house. — No person working on an opener in pressing factory shall be permitted to feed the machine by means of his legs. All such workers shall wear tight clothing's. 4. Cotton Opener. — In all types of openers in use in pressing factories the slope of the feed table shall not be more than one in ten and in no case shall it consist of a smooth metal plate. The beater or toothed rollers of cotton openers in pressing factories shall be guarded by securely fixing across the feed end of the machine a strong guard of metal or wood with sides closed not more than @[30 cms] above the lattice and not less than @[50 cms] in width so arranged that in no circumstances can a man's hand come in connect with the beaters or rollers. Schedule III (Wood working Machinery) 1. Definitions. — For the purpose of this Schedule:— (a) Wood-working machine means a circular saw, band saw, planing machine, chain mortising machine or vertical spindle molding machine operating on wood or cork: ------------------------------------------------------------------------------------------------------------------------ @. Substituted vide Notification No. F1(112)L&E/76 dated 24.3.1979; Rajasthan Gazette Part IV-Ga(1). dated 26.4.1979 (b) Circular saw means a circular saw working in a bench (including a rack bench) but does not include a pendulum or similar saw which is moved towards the wood for the purpose of cutting operation; (c) Band saw means a band saw, the cutting portion of which runs in a vertical direction but does not include a log saw or band re-sawing machine: (d) Planning machine means a machine for overhand planing or for thicknessing or for both operations. 2. Stopping and Starting device. — An efficient stopping and starting device shall be provided on every wood-working machine. The control of this device shall be in such a position as to be readily and conveniently operated by the person in charge of the machine. 3. Space around machines. — The space surrounding every wood-working machine in motion shall be kept free from obstruction. 4. Floors. — The floor surrounding every wood-working machine shall be maintained in good and level condition, and shall not be allowed to become slippery, and as far as practicable shall be kept free from chips or other loose material. 5. Training and supervision. — (1) No person shall be employed at a wood-working machine unless he has been sufficiently trained to work that class of machine, or unless he works under the adequate supervision of a person who has a thorough knowledge of the working of the machine. (2) A person who is being trained to work a wood-working machine shall be fully and carefully instructed as to the dangers of the machine and the precautions to be observed to secure safe working of the machine. 6. Circular saws. — Every circular saw shall be fenced as follows:— (a) Behind and in direct line with the saw there shall be a riving knife, which shall have a smooth surface, shall be strong, rigid and easily adjustable, and shall also conform to the following conditions:- (i) The edge of the knife nearer the saw shall form an are of a circle having a radius not exceeding the radius of largest saw used on the bench. (ii) The knife shall be maintained as close as practicable to the saw, having regard to the nature of the work being done at the time, and at the level of the bench table the distance between the front edge of the knife and the teeth of the saw shall not exceed @[12 mms]: (iii) For a saw of a diameter of less than @[60 cms], the knife shall extend upwards from the bench table to within @[25 mms] of the top of the saw, and for a saw of a diameter of @[60 mms] or over shall extend upwards from the bench table to a height of at least @(28.5 ems]; (b) The top of the saw shall be covered by a strong and easily adjustable guard, with a flange at the side of the saw farthest from the fence. The guard shall be kept so adjusted that the said flange shall extend below the roots of the teeth of the saw. The guard shall extend from the top of the riving knife to a point as low as practicable at the cutting edge of the saw. (c) The part of the saw below the bench table shall be protected by to plates of metal or other suitable material one on each side of the saw: such plates shall not be more than @[15 cms] apart, and shall extend from the axis of the saw out wards to a distance of not less than @[5 cms] beyond the teeth of the saw. Metal plates if not beaded, shall be of a thickness of at least [2.5 mms], or if beaded be of a thickness of at least @[1.25 mms]. -------------------------------------------------------------------------------------------------------------------- @. Substituted vide Notification No. F1(112)L&E/76 dated 24.3.1979; Rajasthan Gazette Part IV-Ga(1). dated 26.4.1979 7. Push sticks. — A push stick or other suitable appliance shall be provided for use at every circular saw and at every vertical spindle molding machine to enable the work to be done without unnecessary risk. 8. Band saws. — Every band saw shall be guarded as follows:— (a) Both sides of the bottom pulley shall be completely encased by sheet or expanded metal or other suitable material: (b) The front of the top pulley shall be covered with sheet or expanded metal or other suitable material: (c) All portions of the blade shall be enclosed or otherwise securely guarded except the portion of the blade between the bench table and the top guide. 9. Planning Machines. — (1) A planning machine (other than a planing machine which is mechanically fed) shall not be used for overhand planing unless it is fitted with a cylindrical cutter block. (2) Every planing machine used for overhand planing shall be provided with a "bridge guard" capable of covering the full length and breadth of the cutting slot in the bench, and so constructed as to be easily adjusted both in a vertical and horizontal direction. (3) The feed roller of every planing machine used for thicknessing, except the combined machine for overhand planing and thicknessing, shall be provided with an efficient guard. 10. Vertical spindle molding machines. — (1) The cutter of every vertical spindle molding machine shall be guarded by the most efficient guard having regard to the nature of the work being performed. (2) The wood being molded at a vertical spindle molding machine shall, if practicable be held in a jig or holder of such construction as to reduce as far as possible, the risk of accident to the worker. 11. Chain mortising machines. — The chain of every chain mortising machine shall be provided with a guard which shall enclose the cutters as far as practicable. 12. Adjustment and maintenance of guards. — The guards and other appliances required under this Schedule shall be— (a) maintained in an efficient state: (b) constantly kept in position while the machinery in motion: and (c) so adjusted as to enable the work to be done without unnecessary risk. 13. Exemptions. — Paragraphs 6, 8, 9 and 10 shall not apply to any wood-working machine in-respect of which it can be proved that other safeguards are provided, maintained and used which render the machine as safe as it would be if guarded in the manner prescribed in this Schedule. Schedule IV (Rubber Mills) 1. Installation of machines. — Mills for breaking down creaking, grating, mixing, refining and warming rubber or rubber compounds shall be so installed that the top of the front roll is not less than forty-six inches above the floor or working level; provided that in existing installations where the top of the front roll is below this height a strong rigid distance bar guard shall be fitted across the front of the machine in such position that the operator cannot reach the nip of the rolls. ------------------------------------------------------------------------------------------------------------------------- @. Substituted vide Notification No. F1(112)L&E/76 dated 24.3.1979; Rajasthan Gazette Part IV-Ga(1). dated 26.4.1979 2. Safety Devices. — (1) Rubber mills shall be equipped with— (a) hoppers so constructed or guarded that it is impossible for the operators to come into contact in any manner the nip of the rolls; (b) horizontal safety trip rods or tight wire cables across both front and rear which will, when pushed or pulled, operate instantly to disconnect the power and apply the brakes, or to reverse the rolls. (2) Safety-trip rods or tight wire cables on rubber mills shall extend across the entire length of the face of the rolls and shall be located not more than @[1.75 metres] above the floor or working level. (3) Safety-trip rods and tight wire cables on all rubber mills shall be examined and tested daily in the presence of the Manager or other responsible person and if any defect is disclosed by such examination and test the mill shall not be used until such defect has been remedied. #[Schedule-V Centrifugal Machines 1. Definition. — "Centrifugal machines" include centrifugal extractors, separators and dryers. 2. Every part of centrifugal machine shall be— (a) of good design and construction and of adequate strength: (b) properly maintained; and (c) examined thoroughly by a competent person at regular intervals. 3. Interlocking guard for drum or basket. — (1) The cage housing of the rotating drum or basket of every centrifugal machine shall be provided with a strong lid. The design and construction of the cage as well as the lid should be such that no access is possible to the drum of basket when the lid is closed. (2) Every centrifugal machine shall be provided with an efficient interlocking device that will effectively prevent the lid referred to in sub-paragraph (1) from being opened while the drum or basket in motion and prevent the drum or basket being set in motion while the lid is in the open position. 4. Braking arrangement. — Every centrifugal machine shall be provided with an effective braking arrangement capable of bringing the drum or basket to rest within as short a period of time as reasonably practicable after the power is cut off. 5. Operating Speed. — No centrifugal machine shall be operated at a speed in excess of the manufacturers rating which shall be legibly stamped at easily visible places both on the inside of the basket and on the outside of the machine casing. 6. Exceptions. — Sub-paragraph (2) of paragraph 3, paragraphs 4 and 5 shall not apply in case of top lung machines or similar machines used in the sugar manufacturing industry.] #[Schedule-VI Power Press 1. Application. — The schedule shall apply to all types of power presses including press brakes, except when used for working hot metal. --------------------------------------------------------------------------------------------------------------- @. Substituted vide Notification No. F1(112)L&E/76 dated 24.3.1979; Rajasthan Gazette Part IV-Ga(1). dated 26.4.1979 #. Added vide Notification No. F.4(3) Shram/88 dated 8.1.1991, published Rajasthan Gazette Part 3(Ga) dated Rajasthan 25.6.1992 2. Definition. — For the purpose of this Schedule— (a) "approved" means approved by the Chief Inspector: (b) "fixed fencing" means fencing provided for the tools of a power press being fencing which has no moving part associated with or dependent upon the mechanism of a power and includes that part of a closed tool which acts as a guard: (c) "Power press" means a machine used in metal or other industries for molding, pressing, blanking, raising, drawing and similar purposes: (d) "safety device" means the fencing and any other safeguard provided for the tools of a power press. 3. Starting and stopping mechanism. — The starting and stopping mechanism shall be provided with safety stop so as to prevent over running of the press or descent of the ram during tool setting etc. 4. Protection of tool and die. — (1) Each press shall be provided with a fixed guard with a slip plate on the underside enclosing the front and all sides of the tool. (2) Each die shall be provided with a fixed guard surrounding its front and sides, and extending to the back in the form of a tunnel through which the pressed article falls to the rear of the press. (3) The design, construction and mutual position of the guards referred to in (1) and (2) shall be such as to preclude the possibility of the workers hand or fingers reaching the danger zone. (4) The machine shall be fed through a small aperture at the bottom of the die guard, but a wider aperture may be permitted for second or subsequent operations if feeding is done through a chute. (5) Notwithstanding anything contained in sub-clauses (1) and (2) an automatic or an inter- locked guards may be used in place of a fixed guard, but where such guards are used they shall be maintained in an efficient working condition and if any guard develops a defect, the power press shall not be operated unless the defect of the guard is removed. 5. Appointment of persons to Prepare power presses for use. — (1) Except as provided in sub-paragraph (4), no person shall set, reset, adjust or try out the tools on a power press or install or adjust any safety device thereon, being installation or adjustment preparatory to production of die proving, or carry out an inspection and test of any safety device thereon required by paragraph 8 unless he— (a) has attained the age of eighteen; (b) has been trained in accordance with the sub-paragraph (2); and (c) has been appointed by the occupier of the factory to carry out these duties in respect of the class or description of power press or the class or description of safety device to which the power press or the safety devices (as the case may be) belongs; and the name of every such person shall be entered in a register in Form 9. (2) The training shall include suitable and sufficient practical instruction in the matters in relation to each type of power press and safety device in respect of which it is proposed to appoint the person being trained. 6. Examination and testing of power presses and safety devices. — (1) No power press or safety device shall be taken into use in any factory for the first time in that factory, or in case of a safety device for the first time on any power press, unless it has been thoroughly examined and tested, in the case of a power press, after installation in the factory, or in the case of a safety device, when in position on the power press in connection with which it is to be used. (2) No power press shall be used unless it has been thoroughly examined and tested by a competent person within the immediately proceeding period of twelve months. (3) No power press shall be unless every safety device (other than fixed fencing) thereon has within the immediately proceeding period of six months when in position on that power press, been thoroughly examined and tested by a competent person. (4) The competent person carrying out an examination and test under the foregoing provisions shall make a report of the examination and test containing the following particulars and every such report shall be kept readily available for inspection: (a) name of the occupier of the factory: (b) address of the factory: (c) identification number or mark sufficient to identify the power press or the safety device: (d) date on which the power press or the safety device was first taken into use in the factory: (e) the date of each periodical thorough examination carried out as per requirements of sub-paragraph (2) above: (f) particulars of any defects affecting the safety working of the power press or the safety device found at any such thoroughly examination and steps taken to remedy such defects. 7. Defects disclosed during a thorough examination and tests. — (1) Where any defect is disclosed in any power press or in any safety device by any examination and test under paragraph 6 and In the opinion of the competent person carrying out the examination and test, either— (a) the said defect is a cause of danger to workers and in consequence the power press in safety device (as the case may be) ought not to be used until the said defect has been remedied: or (b) the said defect may become a cause of danger to workers and in consequence the power press or safety device (as the case may be) ought not to be used after the expiration of a specified period unless the said defect has been remedied. Such defect shall, as soon as possible after the completion of the examination and test, be notified in writing by the competent person to the occupier of the factory and, in the case of a defect falling within clause (b) of this sub-paragraph such notification shall include the period within which, in the opinion of the competent person, the defect ought to be remedied. (2) In every case where notification has been given under this paragraph, a copy of the report made under paragraph 6 (4) shall be sent by the competent person to the inspector for the area within fourteen days of the completion of the examination and test. (3) Where any such defect is notified to the occupier in accordance with the foregoing provisions of this paragraph the power press or safety device (as the case may be) having the said defect shall not bet used:- (a) in the case of a defect falling within clause (a) of sub-paragraph (1). until the said defect has been remedied: and (b) in the case of defect falling within clause (b) of sub- para-graph (1), after the expiration of the said defect has been remedied. (4) As soon as is practicable after any defect of which notification has been given under sub-paragraph (1) has been remedied, a record shall be made by or on behalf of the occupier stating the measures by which and the date on which the defect was remedied. 8. Inspection and test of safety devices. — (1) No power press shall be used after setting, resetting or adjustment of the tools there on unless a person appointed or authorised for the purpose under paragraph 5 has inspected and tested every safety device thereon while it is in position on the said power press: Provided that an inspection, test and certificate as aforesaid, shall not be required where any adjustment of the tools has not caused or resulted in any alteration to or disturbance of any safety device on the power press and if, after the adjustment of the tools, the Safety devices remain, in the opinion of such as a person as aforesaid; in efficient working order. (2) Every power press and every safety devices thereon while it is in position on the said power press shall be inspected and tested by a trained person everyday. 9. Defect disclosed during an inspection and test. — (1) Where it appears to any person as a result of any inspection and test carried out by him under paragraph 8 that any necessary safety device is not in position or is not properly in position on a power press or that any safety device which is in position on a power press is not in his opinion suitable, he shall notify the manager forthwith: (2) Except as provided in sub-paragraph (3) where any defect is disclosed in a safety device by any inspection and test under para-graph 8, the person carrying out the inspection, and test shall notify the manager forthwith. (3) Where any defect in a safety device is the subject of a notification in writing under paragraph 7 by virtue of which the use of the safety device may be continued during a specified period without the said defect having been remedied, the requirement in sub- paragraph (2) of this paragraph shall not apply the said defect until the said period has expired. 10. Identification of power presses and safety devices. — For the purpose of identification every power press and every safety device provided for the same shall be distinctively and plainly marked. 11. Training and instructions to operators. — The operators shall be trained and instructed in the safe method of work before starting work on any power press. 12. Exemptions. — (1) If in respect of any factory, the Chief Inspector is satisfied that owing to the circumstances or in frequency of the processes or for any other reason, all or any of the provisions of this Schedule are not necessary for the protection of the workers employed in any power press or any class or description of power press or in the factory the Chief Inspector may by a certificate in writing (which he may in his description revoke at any time), exempt such factory from all or any of such provisions subject to such conditions if any as he may specify therein. (2) Where such exemption is granted, a legible copy of the certificate, showing the condition (if any) subject to which it has been granted shall be kept posted in the factory in a position where it may be conveniently read by the persons employed.] @[Schedule VII Shears, Slitters and Guillotine Machines. 1. Definition. — For the purpose of this Schedule :— (a) "Guillotines" means a machine ordinarily equipped with straight, bevel-edged blade operating vertically against a stationary resisting edge and used for cutting metallic or non- metallic substances; (b) "Shears" or "Shearing machine" means a machine ordinarily equipped with straight bevel-edged blades operating vertically against resisting edges, or with rotary, overlapping cutting wheels, and used for shearing metals or non-metallic substances: (c) "Slitter" or "Slitting machine" means a machine ordinarily equipped with circular disc type knives, and used for trimming or cutting into metal or non-metallic substances or for slitting them into narrow strips; for the purpose of this schedule, this term includes bread or other food slices equipped with rotary knives or cutting discs. 2. Guilloting and shears. — (1) Where practicable, a barrier metal guard of adequate strength shall be provided at the front of the knife, fastened to the machine frame and shall be so fixed as would prevent any part of the operator's body to reach the descending blade from above below or through the barrier guard or from the sides: Provided that in case of machines used in the Paper Printing and allied industries, where a fixed barrier metal guard is not suitable on account of the height and volume of the material being fed, there shall be provided suitable starting devices which require simultaneous action of both the hands of the operator or an automatic device which will remove both the hands of the operator from the danger zone at every descent of the blade. (2) At the back end of such machines, an inclined guard shall be provided over which the slit pieces would slide and be collected at safe distance in a manner as would prevent a person at the hack from reaching the descending blade. (3) Power-driven guillotine cutters, except continuous feed trimmers, shall be equipped with— (a) Starting devices which require the simultaneous action of both hands to start the cutting motion and of at least one hand on a control during the complete stroke of the knife; or (b) an automatic guard which will remove the hands of the operator from the danger zone at every descent of the blade, used in conjunction with one hand starting devices which require two distinct movements of the device to start the cutting motion, and so designed as to return positively to the non-starting position after each complete cycle of the knife. (4) Where two or more workers are employed at the same time on the same power-driven guillotine cutter equipped with two-hand control, the device shall be so arranged that each workers shall be required to use both hands simultaneously on the safety trip to start the cutting motion, and at least one hand on a control to complete the cut. (5) Power driven guillotine cutters, other than continuous trimmer, shall be provided, in addition to the brake or other stopping mechanism, with an emergency device which will prevent the machine from operating in the event of failure of the brake when the starting mechanism is in the non-starting position. ------------------------------------------------------------------------------------------------------------------------- @. Added vide Notification No. F.4(3) Shram/88 dated 8.1.1991, published Rajasthan Gazette Part 3(Ga) dated Rajasthan 25.6.1992 3. Slitting Machines. — (1) Circular disc-type knives on machines for cutting metal and leather, paper, rubber, textiles, or other nonmetallic substances, shall, if within reach of operators standing on the floor or working level, be provided with guards enclosing the knife edges at all times at near as practicable to the surface of the material, and which may either.— (a) automatically adjust themselves to that thickness of the material: or (b) be fixed or manually adjusted so that the space between the bottom of the guard and the material will not exceed 6 mm (1/ 4 In.) at any time. (2) Portions of blades underneath the tables or benches of slitting machine shall be covered by guards. 4. Index cutters and vertical paper slotters. — Index cutters, and other machines for cutting strips from the ends of books, and for similar operations, shall be provided with fixed guards. so arranged that the fingers of the operators cannot come between the blades and the tables. 5. Corner cutter. — Corner cutters, used in the manufacture of paper boxes, shall be equipped with (a) Suitable guard, fastened to the machines in front of the knives and provided with slots or perforations to afford visibility of the operations; or (b) Other guards equally efficient for the protection of the fingers of the workers. 6. Band knives. — Band wheels on bank knives, and all portion of the blades except the working side between the sliding guide and the table on vertical machines or between the wheel guards on horizontal machines, shall be completely enclosed with hinged guards of sheet metal not less than 1 mm. (0.04 in.) in thickness or of other material of equal strength.] Rules prescribed under sub-section (1) of Section 22 @[54. Register of specially trained adult workers.— In every factory a register shall be maintained in Form No.8 in which the names and other particulars of every such worker as may be employed or required to perform the duties specified in sub- section (1) of Section 21 shall be entered]. #[54A. Tight fitting clothing. — A worker required to wear tight fitting clothing under sub- section (1) of section 22 shall be provided by the occupier with such clothing which shall consist of at least a pair of closely fitting shirts and a closely fitting half sleeve shirt or vest. Such clothing shall be returned to the occupier on termination of service or when new clothing is provide.] Rule prescribed under Section 41

Previous and next

All provisions of Rajasthan Factories Rules,1951

Questions people ask

Is rule 53 of Rajasthan Factories Rules,1951 still in force?

No repeal of Rajasthan Factories Rules,1951 is recorded.