LawGrids logoLAWGRIDS.ORG

Rule 94, Delhi Factories Rules, 1950: Register to be maintained in case of exemption under section 84

Delhi Factories Rules, 1950 - Rule 94

Text of rule 94

Register to be maintained in case of exemption under section 84

94. Register to be maintained in case of exemption under section 84-- (1) Where an exemption is granted under Section 84, the Manager shall maintain a Register showing the position of each worker as regards leave due, leave taken and wages granted. (2) He shall display at the main entrance of the factory, a notice giving full details of the system established in the factory for leave with wages and shall send a copy of it to the Inspector. (3) No alteration shall be made in the scheme approved by the Chief Commissioner at the time of granting exemption under Section 84 without its previous sanction. CHAPTER IX SPECIAL PROVISIONS Rule prescribed under Section 87 95. Dangerous Operations- (1) The following operations (Manufacturing process or operation) when carried on in a factory are declared to be dangerous operations under Section 87:- 1. Manufacture of aerated water and processes incidental thereto. 2. Electrolytic plating or oxidation of metal articles by use of an electrolyte containing chromic acid and other chromium compounds. 3. Manufacture and repair of electric accumulators. 4. Glass manufacture. 5. Grinding or glazing of metals. 6. Manufacture and treatment of lead and certain compounds of lead. 7. Generating petrol gas from petrol. 8. Cleaning or smoothing of articles by a jet of sand, metal shot or grit or other abrasive propelled by a blast of compressed air or steam. 9. Liming and tanning of raw hides and skins and processes incidental thereto. 10. Manufacture of Pottery. 11. Lead Processing. 12. Chemical works and processes incidental thereto. 13. Manufacture of articles from refractory materials. 14. Handling and processing of asbestos for manufacture of any article of asbestos and process of manufacture or otherwise in which asbestos is used in any form. 15. Handling or manipulation of corrosive substances. 16. Compression of Oxygen or Hydrogen produced by electrolysis of water. 17. Process of extracting of oil and fats from extraction plants. 18. Manufacture of manipulation of Manganese and its compounds. 19. Manufacture of manipulation of dangerous pesticides- 20. Manufacture, handling and use of Benzene and substances containing Benzene. 21. Manufacturing process or operation is Carbon Di Sulphide plants. 22. Manufacture and manipulation of carcenogenic dye intermediates. 23. Operation involving high noise levels. 24. Highly flammable compressed gases. 25. Operations in foundries. 26. Manipulation or stone or any other material containing Free Silica. (2) The provisions specified in the Schedules annexed hereto shall apply to any class or description of factories wherein dangerous manufacturing process or operation specified in each Schedule are carried out. (2-A) (a) For the medical examination of workers to be carried out by the Certifying Surgeon as required by the Schedule annexed to this rule, the occupier of the factory shall pay fees at the rate of Rupees one per year for each worker. (b) The fees prescribed in sub-rule 2A shall be exclusive of any charges as for biological, radio-logical or other test which may have to be carried out in connection with the medical examinations. Such charges shall be payable by the occupier. (c) The fees to be paid for medical examinations shall be paid into the local treasury under the head of account Major Head 087, Labour and Employment, Receipts Under Labour Law. Receipts under various Acts, Fee realised under Factories Act. (d) For each biological and radiological examination of workers take carried out by the certifying Surgeon as required by the schedules annexed to this rule the occupier of the factory shall pay fees at the rate of rupees five and twelve respectively for each worker at the time of each examination . (3) The Rule shall come into force in respect of any class or description of factories wherein the said operations are carried on such dates as the Chief Commissioner may, by notification in the official gazette, appoint in this behalf. (4) Notwithstanding the provisions specified in the Schedule annexed to this rue, the Inspector or the Chief Inspector, as the case may be, by issue of order in writing to the manager, or occupier or both, direct to carry out such ____ and within such time, as may be specified in such order with a view to ____ conditions dangerous to the health of the workers or to suspend any process, where such process constitutes in the opinion of the Inspector or the Chief Inspector, as the case may be, danger of poisoning or toxicity. SCHEDULE I Manufacture of Aerated Waters and processes incidental thereto 1. Fencing of machines- All machines for filling bottles or syphons shall be so constructed, placed or fenced as to prevent, as far as may be practicable, a fragment of a bursting bottle or syphon from striking any person employed in the factory. 2. Face guards and gauntlets- (1) The occupier shall provide and maintain in good condition for the use of all persons engaged in filling bottles or syphons: (a) suitable face-guards to protect the face, neck and throat, and (b) suitable gauntlets for both arms to protect the whole hand and arms. Provided that : (i) paragraph 2(1) shall not apply where bottles are filled by means of an automatic machine so constructed that no fragment of a bursting bottle can escape, and (ii) where a machine is so constructed that only one arm of the bottler at work upon it is exposed to danger, a gauntlet need not be provided for the arm which is not exposed to danger. (2) The occupier shall provide and maintain in good condition for the use of all persons engaged in corking, crowning, screwing, wiring, foiling, capsuling, sighting or labelling bottles or syphons- (a) suitable face-guards to protect the face, neck and throat, and (b) suitable gauntlets for both arms to protect the arms and at least half of the palm and the space between the thumb and forefinger . 3. Wearing of face guards and gauntlets- All persons engaged in any of the processes specified in paragraph 2 shall, while at work in such processes, wear the face guards and gauntlets provided under the provisions of the said paragraph. SCHEDULE II Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts or metals such as chromium, nicklex, cadmium, zinc, copper, silver, gold etc.- 1. Definitions- For the purposes of this Schedule :- (a) "electrolytic process" means the electrolytic plating or oxidation of metal articles by the use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. (b) "bath" means any vessel used for an electrolytic process or for any subsequent process; and (c) "employed" means employed in any process involving contact with liquid from a bath. 2. Exhaust draught- An efficient exhaust draught shall be applied to every vessel in which an electrolytic process is carried on. Such draught shall be provided by mechanical means and shall operate on the vapour or spray given off in the process a near as may be at the point of origin. The exhaust draught appliances shall be so constructed, arranged and maintained as to prevent the vapour or spray entering into any room or place in which work is carried on. 3. Prohibition relating to women and young persons- No women, adolescent or child shall be employed or permitted to work at a bath. 4. Floor of workrooms- The floor of every workroom containing a bath shall be impervious to water. The floor shall be maintained in good and level condition and shall be washed down at least once a day. 5. Protective devices- (1) The occupier shall provide and maintain in good and clean condition the following articles of protective devices for the use of all persons employed on any process at which they are liable to come in contact with liquid from a bath and such devices shall be worn by the persons concerned- (a) waterproof aprons and bibs; and (b) for persons actually working at a bath, loose fitting rubber glove and rubber or other waterproof footwear, and chemical goggles. (2) The occupier shall provide and maintain for the use of all persons employed suitable accommodation for the storage and drying of protective devices. 6. Water facilities- (1) There shall be provided and maintained in good repairs for the use of all persons employed in electrolytic process and processes incidental to it- (a) a wash place under cover, with either- (i) a trough with a smooth impervious surface filled with a waste pipe, and of sufficient length to allow at least 60 cms for every 5 persons employed at anyone time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 60 cms, or (ii) at least one wash basin for every five such persons employed at anyone time, fitted with a waste pipe and having a constant supply of water laid on. (b) a sufficient supply of clean towels renewed daily, and soap or other suitable cleaning material. (2) In addition to the facility in sub-paragraph 1, an approved type of emergency shower with eye fountain shall be provided and maintained in good working order. Whenever necessary, in order to ensure continuous water supply, storage tank of 1500 litres capacity shall be provided as a source of clean water for emergency use. 7. Cautionary placard- A cautionary placard in the form specified below and printed in the language of the majority of the workers employed shall be affixed in a prominent place in the factory where it can be easily and conveniently read by the workers. CAUTIONARY NOTICE A. Electrolytic plating- 1. Chemicals handled in this plant are corrosive and poisonous. 2. Smoking, chewing tobacco, eating food or drinking, in this area in prohibited. No food stuff or drink shall be brought in this area. 3. Some of these chemicals may be absorbed through the skin and may cause poisoning. 4. A good wash shall be taken before meals. http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//factoryrules/ 5. Protective devices supplied shall be used while working in this area. 6. Spillage of the chemicals on any part of the body or on the floor shall be immediately washed away with water. 7. All workers shall report for the prescribed medical tests regularly to protect their own health. B. Medical facilities and records of examinations and tests - (1) The occupier of every factory in such electrolytic processes are carried on shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Chief Inspector of Factories; (b) provide to the said medical practitioner all the necessary facilities for the purpose referred in clause (a); and (c) maintain a sufficient supply of suitable barrier cream, ointment and Impermeable water proof plaster in a separate box readily accessible to the workers and used solely for the purpose of keeping these substances. In case cyanides are used in the bath, the box shall also contain an emergency cyanide kit. (2) The medical practitioner shall examine all workers before they are employed in electrolytic processes. Such examination in case of chrome plating shall include inspection of hands, forearms and nose and will be carried out once at least in every fortnight. (3) The record of the examinations referred to in sub-paragraph (2) shall be maintained in a separate register approved by the Chief Inspector of Factories which shall be kept readily available for inspection by the Inspector. 9. Medical examination by the Certifying Surgeon- (1) Every worker employed in the electrolytic processes shall be examined by a Certifying Surgeon before his first employment. Such examination shall include X- ray of the chest and- (a) in case of chromium plating include examination for nasel septum perforation and test for chromium in urine; (b) in case of nickel plating, test for nickel in urine; and (c) in case of cadmium plating, test for cadmium in urine and microglobullin in urine. (2) No worker shall be employed in any electrolytic process unless certified fit for such employment by the Certifying Surgeon. (3) Every worker employed in the electrolytic processes shall be re-examined by a Certifying Surgeon at least once in every year, except in case of the workers employed in cadmium, chromium and nickel plating processes for whom this examination shall be carried out once in every six months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified under sub-paragraph (1) excluding the X-ray of the chest which shall not be required normally to be carried out earlier than once in three years. (4) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 5. The record of examination and re-examination carried out shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 17. (5) The certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (6) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the electrolytic processes on the ground that continuance therein would involve danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the said processes. The person declared unfit in such circumstances shall be provided with alternate placement facility unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (7) No person who has been found unfit to work as said in sub-paragraph (6) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. SCHEDULE III Manufacture and repair of electric accumulators 1. Savings- This schedule shall not apply to the manufacture or repair of electric accumulators or parts thereof not containing lead or any compound of lead; or to the repair on the premises of any accumulator forming part of a stationary battery. 2. Definitions- For the purposes of this Schedule:- http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//factoryrules/ (a) "Lead Process " means the melting of lead or any material containing lead casting, pasting, lead burning, or any other work including trimming, or any other abrading or cutting of pasted plates, involving the use, movement or manipulation of, or contact with, any oxide of lead. (b) "Manipulation of raw oxide of lead" means any lead process involving any manipulation on movement of raw oxides of lead other than its conveyance in a receptacle or by means of an implement from one operation to another. (c) "Suspension" means suspension from employment in any lead process by written certificates in the Health Register (Form 17) signed by the Certifying Surgeon, who shall have power of suspension as regards all persons employed in any such process. 3. Prohibition relating to women and young persons- No woman or young person shall be employed or permitted to work in any lead process or any room in which the manipulation of raw oxide of lead or pasting is carried on. 4. Separation of certain processes- Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another, and from any other process. (a) Manipulation of raw oxide of lead; (b) Pasting; (c) Drying of pasted plates; (d) Formation with lead burning ("tracking") necessarily carried on in connection therewith; (e) Melting down of pasted plates. 5. Air Space-- In every room in which a lead process is carried on, there shall be at least 500 cubic feet of air space for each person employed therein and in computing this air space no height over 12 feet shall be taken into account. 6. Ventilation- Every work-room shall be provided with inlets and outlets of adequate size as to secure http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//factoryrules/ and maintain efficient ventilation in all parts of the room. 7. Distance between workers in pasting room- In every pasting room the distance between the centre of the working position of any paster and that of the paster working nearest to him shall not be less than six feet. 8. Floor of work-rooms- (1) The floor of every room in which a lead process is carried on shall be- (a) Of cement or similar material so as to be smooth and impervious to water; (b) Maintained in sound condition; (c) Kept free from materials, plant or other obstruction not required for or produced in the process carried on in the room. (2) In all such rooms other than grid casting shop the floor shall be cleaned daily after being thoroughly sprayed with water at a time when no other work is being carried on in the room. (3) In grid casting shops the floor shall be cleansed daily. (4) Without prejudice to the requirements of sub-paragraphs (1) (2) and (3), where manipulation of raw oxide of lead or pasting is carried on, the floor shall also be- (a) Kept constantly moist while work is being done; (b) Provided with suitable and adequate arrangements for drainage; (c) thoroughly washed daily by means of a house pipe. 9. Work-benches- The work-benches at which any lead process is carried on shall- (a) have smooth surface and be maintained in sound condition; (b) be kept free from all material or plant not required for, or produced in the process carried on thereat; and all such work-benches other than those in grid casting shops shall- (c) be cleansed daily either after being thoroughly damped or by means of a suction cleaning apparatus at a time when no other work is being carried on thereat and all such work-benches in grids casting shops, shall- (d) be cleansed daily; and every work-bench used for pasting shall- (e) be covered throughout with sheet lead or other impervious material; (f) be provided with raised edges; (g) be kept constantly moist while pasting is being carried on. 10. Exhaust draught- The following processes shall not be carried on without the use of an efficient exhaust draught- (a) Melting of lead or materials containing lead; (b) Manipulation of raw oxide of lead, unless done in an enclose apparatus so as to prevent the escape of dust into the work-room; - (c) Pasting; - (d) Trimming, brushing, filing or any other abrading or cutting of pasted plates giving rise to dust; (e) Lead burning other than; (i) "tacking" in the formation rooms; (ii) Chemical burring for the making of lead linings for cell case necessarily carried on in such a manner that the application of efficient exhaust in impracticable. Such exhaust draught shall be affected by mechanical means and shall operate on the dust or fume given off as nearly as may be at its point of origin, so as to prevent its entering the air of any room in which persons work. 11. Fumes and gases from melting pots- The products of combustion produced in the heating of any melting pot shall not be allowed to escape into a room in which persons work. 12. Container for dross- A suitable receptacle with tightly, fitting cover shall be provided and used for dross as it is removed from every melting pot. Such receptacle shall be kept covered while in the work-room, except when dross is being deposited therein. 13. Container for lead waste-- A suitable receptacle shall be provided in every work-room in which old plates and waste materials which may give risk to dust shall be deposited. 14. Racks and Shelves in drying room- The racks or shelves provided in any drying room shall not be more than 8 feet from the floor nor more than 2 feet in width; provided that as regards racks or shelves set or drawn from both sides the total width shall not exceed 4 feet. Such racks or shelves shall be cleansed only after being thoroughly damped unless an efficient suction cleaning apparatus is used for this purpose. 15. Medical Examination- (a) Every person employed in a leap process shall be examined by the Certifying Surgeon within seven days preceding or following the date of his first employment in such process and thereafter shall be examined by the Certifying Surgeon once in every calendar month or at such other intervals as may be specified in writing by the Chief Inspector, on a day of which due notice shall be given to all concerned. 'First Employment' means first employment in a lead process in the factory or workshop and also re-employment therein in a lead process following any & cessation of employment in such process for a period exceeding three calendar months. (b) A Health Register in Form No.17 containing the names of all persons employed in a lead process shall be kept. (c) No person after suspension shall be employed in a lead process without written sanction from the Certifying Surgeon entered in or attached to the Health Register. 16. Protective clothing- Protective clothing shall be provided and maintained in good repair for all persons employed in- (a) manipulation of raw oxide of lead; (b) pasting; (c) the formation room; and such clothing shall be worn by the persons concerned. The protective clothing shall consist of a waterproof apron and waterproof footwear; and also as regards persons employed in the manipulation of raw oxide of lead or in pasting head coverings. The head coverings shall be washed daily. 17. Mess Room- There shall be placed and maintained for the use of all persons employed in a lead process and remaining on the premises during the mean intervals, a suitable mess- room, which shall be furnished with (a) sufficient tables and benches, and (b) adequate means for warming food. The mess-room shall be provided under the charge of a responsible person and shall be kept clean. 18. Cloak-Room- There shall be provided and maintained for the use of all persons, employed in a lead process- (a) a cloak-room for clothing put off during working hours with adequate arrangements for drying the clothing if wet. Such accommodation shall be separate from any mess-room; (b) separate and suitable arrangements for the storage of protective clothing provided under paragraph 16. 19. Washing facilities- There shall be provided and maintained in a clean state and in good repair for the use of all persons employed in a lead process- (a) A wash-place under cover, with either- (i) a trough with a smooth impervious surface fitted with a waste pipe, without plug and of sufficient length to allow of at least two feet for every five such persons employed at anyone time, and having a constant supply of water from taps or jets above the trough at intervals of not more than two feet; or (ii) at least one wash basin for every five such persons employed at anyone time, fitted with a waste pipe and plug and having a constant supply of water laid on; (iii) a sufficient supply of clean towels made of suitable renewed daily, which supply, in the case of pasters and employed in the manipulation of raw oxide of lead, shall include a separate marked towel for each such worker; (iv) a sufficient supply to soap or other suitable cleansing material and of nail brushes. (b) There shall in addition be provided means of washing in close proximity to the rooms in which manipulation of raw oxide of lead or pasting is carried on, if required by notice in writing from the Chief Inspector. 20. Time to be allowed for washing- Before each meal and before the end of the day's work, at least ten minutes, in addition to the regular meal times shall be allowed for washing to each person who has been employed in the manipulation of raw oxide of lead or in pasting; Provided that if there be one basin or two feet of trough for each such person this Rule shall not apply. 21. Facilities for bathing- Sufficient batch accommodation to the satisfaction of the Chief Inspector shall be provided for all persons engaged in the manipulation of raw oxide of lead or in pasting, and a sufficient supply of soap and clean towels. 22. Food, drinks, etc. prohibited in work-rooms- No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any work-room in which any lead process is carried on.

Previous and next

All provisions of Delhi Factories Rules, 1950

Questions people ask

Is rule 94 of Delhi Factories Rules, 1950 still in force?

No repeal of Delhi Factories Rules, 1950 is recorded.