Appendix, Delhi Factories Rules, 1950: APPENDIX
Delhi Factories Rules, 1950 - Appendix
Text of appendix
APPENDIX
APPENDIX
NOTIFICATION
Dated the April, 1969
No. F. 11 (32) /58 I & L :- In exercise of the powers conferred by sub-section (3) of
Section 26 of the Factories Act, 1948 read with the Government of India, Ministry of
Labour & Employment Notification No. S. 0.108, dated 14th February,1958, the Chief
Commissioner, Delhi hereby makes the following amendment to the Delhi Factories
Rules, 1950, the draft of which was published with his Notification of even number
dated 10th July, 1958 -
AMENDMENT
In the said Rules, 53 the following rule shall be inserted, namely -
*53-A- The provisions of sub-section (2) which prohibit the sale or letting
on hire of certain machines of Section 26 of the Act shall extend to the
class or description of machines specified in the first column of the
Schedule suspended to this Rule.
(2) No machine specified in the firs t column of the Schedule above mentioned
shall be sold or let on hire by any person for use in any factory after the
date of bringing these rules in force unless it is constructed or provided
with guards, fencing or other protective devices in conformity with the
requirements set opposite to the class of description to which the machine
belongs in the second column of the said Schedule.
(3) Provision under these rules shall not be deemed to relieve any occupier or
manager of a factory of his responsibilities under Section 21 of the
Factories Act, 1948.
SCHEDULE
Requirements as to the construction and safeguards or machines
First Column Second Column
Class or Description
of Machines
Requirements
Blowing Room
Machinery.
1. (a) Beater covers and the door immediately over the
dirt grid shall be fitted with an automatic looking
arrangement which renders it impossible to open the
covers while the beater is still running, or to restore
the machinery until the doors have been closed.
(b) The covers over the porcupine cylinders shall be
fitted with an automatic, looking arrangement which
renders it impossible to open the covers while the
cylinders are still running or to restart the machinery
until the covers have been closed.
2. The nip between the cage wheels and cylinder wheels
shall be efficiently protested on all machines. Guards
shall be provided extending round the cute edge of
both the wheels.
3. Projecting ends of beater shafts shall be respectively
covered.
4. Spiked or fluted rollers on hand fed crispers or lattices
on breakers and openers shall be so covered as to
prevent access to intake.
5. Exposed toothed gar ding on all machines shall be
securely covered,
6. On lap forming southechers with weighing rollers the
lap roller shall be so protected that as soon as the
http://labour.delhigovt.nic.in/act/details_rules/the%20delhi%20factory%20rules,%201950//forms/
weights are ran down the lap roller as completely
covered.
1. All feed roller wheels, doffer and narrow wheels,
side shaft wheels, cylinder wheels roller wheels, and,
all thatched gearing in spite the Boiler head shall be
securely covered.
2. All cylinder doors shall be fitted with an automatic
leading Section which will prevent the door from being
opened until the cylinder has ceased to receive, to
restart the machine until the door has again been
closen.
3. Licke-it shall be completely covered and the covers
shall be screwed down so that they cannot readily be
lifted while the machine is in motion.
4; Over the deferr, covers shall be extended as far as
is reasonably practicable.
5. All driven pulleys shall be plated.
1. Exposed toothed gearing on all machines shall be
securely covered.
2. On all machines the lap forming rollers shall be
provided with a guard or cover which shall either.
(i) Prevent access to the intake of the lap roller and
fluted roller so long as the weighing rack is down, or
(ii) Prevent access to the intake of the lap roller and
fluted roller and be so locked that the guard or cover
cannot be raised until the machine is stopped and the
machine cannot be started until the guard of cover is
closed.
Combers. 1. Exposed toothed gearing on all machines shall be
securely covered.
2. The toothed gearing in side the coiler head shall be
securely covered.
3. The cylinder shall be provided with a guard or guards
which shall prevent access too it whilst in motion and
the guard or guards shall be so locked that they
cannot be raised until the machine cannot be started
until all guards have been closed and locked.
Drawing Frames. 1. The roller gearing shall be effectively covered and the
cover shall be so locked that it cannot be raised until
the machine is stopped and the machine cannot be
started until the cover is closed.
2. The under shaft of the frame shall be covered and the
pulley on the under shift shall be plated.
3. All toothed gearing and shafts connected with the
driving of the roller and sliver cans shall be securely
covered.
4. The calendar roller gears shall be provided with
guards independent of the cylinder roller cover and
the coils cage and coiler head shall be covered.
Speed Frames. 1. All jack boxes shall be fitted with automatic locks
which shall prevent the doors being opened while the
machinery is in motion and shall rends it impossible to
restart the machine until the door has been closed.
2. Draft change wheels, back roller and carrier wheels
twist and carrier wheels, bobbin shaft driving wheels
and swing wheels, lifter wheels and button cone drum
wheels shall be securely covered.
3. The bobbin skew gear wheels shall either,
(i) Be covered over the top, and their total enclosure
be completed by up right metal plates extending at
the back from the roller beam to the floor, and at the
front from the cover over the top of the wheels to the
floor and screen arranged as to from continuous
screen at every position of the lifter rail; or
(ii) Be covered over the top and the covers be
extended both in front and behind round the edges of
the wheels to within not more than one quarter of an
inch from the spindles.
4. Spindle skew gear shall be effectively covered.
5. Lifts rack wheels shall be securely covered, and the
guard to be such that it will effectively protected the
nip both as the rail wishes and as it falls.
6. All balance weights shall be waste with cycles forming
part of the weights themselves.
Ring and Throttle
Frames
1. All toothed gearing such as headstock wheels draft
wheels and these driving the lifting gear shall be
securely covered. The guard covering the draft pinion
wheels shall be so locked that the cover cannot be
raised until the machine is stopped and the machine
cannot be started until the cover is closed. The outer
and of the frame shall be filled in with metal plates.
2. On machines with double tin rollers a guard shall be
fitted along the whole length of the nip between the
rollers.
Winding Frames. 1. Traverse motion and mangle rotion wheels shall be
effectively covered.
2. Where there is a double tin roller the nip, shall be
provided with a guard.
3. Bevel wheels driving spindles of Jambo cop winding
frames shall be effectively covered.
4. Exposed toothed gearing on all types of machines
shall be effectively.
Warping 1. Bevel wheels on all warping machines shall be
effectively covered.
2. All toothed gearing on chain beaming, winding on
machines and other types of winging machines shall
be effectively covered.
Clay Pans and fize
Beeks.
1. . All toothed gearing and shafting connected therewith
shall be effectively guarded.
Taping Machine. 1. The distance between the periphery of the smaller and
large cylinders shall not be less than six inches and
where this distance is less than six inches the nip shall
be effectively guarded.
2. The following dangerous moving parts shall be
effectively covered.
(a) Bevel wheels on side shaft.
(b) Bevel wheels and upright shaft for driving colored
or top box.
(ac) Measuring motion wheels.
(d) Speed change gears.
(e) Intake of drag and measuring rollers.
(bf) Blinder at end of dry taping machines
Looms :- 1. To prevent shuttle flying out when the loom is running
the slay of the loom shall be provided with guard. It is
to be fitted as low as possible so that the clearance
between the guard and the shuttle when the shuttle is
placed on the fall of the cloth with the loom crank
shaft on the top centre does not exceed ½ inches and
on 1ooms other than velvet looms or looms of 60
inches reed space between the guard and the sample
shall not be less .than 5/8 inch unless the guard is so
designed and constructed as to prevent injury from
trapping between them.
The guard shall extend to at least half the shuttles
length from the spindle stud belt on over pick looms,
or the trash plate on under pick looms.
2. Between the hammer head/ and the beam there shall
be space of not less than 3/4 inches unless the
hammer head always extends over the breast beam.
3. Duck bills on all loose reed looms shall be effectively
protected.
4. All gearing including tappet and twill motion wheels
shall be completely encased. On small and similarly
barral motions the top and bottom pairs of bevel
wheel and that portion of Shaft connecting them which
above the warp shall be effectively covered
5. There shall be a space of not less than one inch left
between the connecting rode driving the dobby and
the framework of the look, and between the stay and
the picking stick and picking stick and framework a
space of not less than two inches.
Plaiting Machines. 1. All the toothed gearing including the gearing driving
the bottom shaft shall be effectively covered.
2. At the delivery and between the knife and the card bar
a guard shall be provided.
3. Side arms shall be effectively covered.
Shearing and
cropping Machines.
1. All revelling knives shall be fitted with covers so as to
prevent access thereto whilst the machine is in motion
and when possible, the covers shall be so locked that
no one of them can be raised until the machine is
stopped, and the machine cannot be started until all
the covers are closed.
2. All the exposed toothed gearing shall be effectively
covered.
*Subs. vide Notification No. F.11 (32)/58-19 L Dt. April, 59.
Previous and next
Questions people ask
Is appendix of Delhi Factories Rules, 1950 still in force?
No repeal of Delhi Factories Rules, 1950 is recorded.