LawGrids logoLAWGRIDS.ORG

Rule 5310, Uttar Pradesh Factory Rules, 1950: Washing facilities

Uttar Pradesh Factory Rules, 1950 - Rule 5310

Text of rule 5310

Washing facilities

5310. Washing facilities.—There shall be provided and maintained in cleanly state and in good repair for the use of all persons employed in the processes specified in paragraph 3 : (a) a wash place with either— (i) a trough with a smooth impervious surface fitted with a waste pipe, without plug, and of sufficient length to allow of at least two feet for every five such persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than 2 feet; or (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having an adequate supply of water laid on or always readily available; and a sufficient supply of clean towels made of suitable materials renewed daily with a sufficient supply of soap or other suitable cleansing material and of nail brushes, and (b) a sufficient number of stand-pipes with taps—the number and location of such stand-pipes shall be to the satisfaction of the Chief Inspector. 11. Medical Examination.—(a) Every person employed in any process specified in paragraph 3 54and on glass blowing shall be examined by the Certifying Surgeon within seven days preceding or following the date of his first employment in such process and thereafter shall be examined by the Certifying Surgeon once in every calendar month or at such other intervals as may be specified in writing by the Chief Inspector on a day of which due notice shall be giving to all concerned. (b) A Health Register in Form No. 17 containing die names of persons employed in any process specified in paragraph 3 and on glass blowing shall be kept. (c) No person after suspension shall be employed in any process specified in paragraph 3 54and on glass blowing without written sanction from the Certifying Surgeon entered in or attached to the health register. SCHEDULE V Grinding or Glazing of Metals and Process Incidental thereto 1. Definitions.—For the purposes of this schedule— (a) "Grindstone" means a grindstone composed of natural or manufactured sandstone but does not include a metal wheel or cylinder into which blocks of natural or manufactured sandstone are fitted. (b) "Abrasive wheel" means a wheel manufactured of bounded emery or similar abrasive. (c) "Grinding" means the abrasion by aid of mechanical power, of metal, by means of a grindstone or abrasive wheel. (d) "Glazing" means the abrading, polishing or finishing, by aid of mechanical power, of metal, by means of any wheel, buff, mop or similar appliance to which any abrading or polishing substance is attached or applied. (e) "Racing" means the turning up, cutting or dressing of a revolving grindstone before it is brought into use for the first time. (f) "Hacking" means the chipping of the surface of a grindstone by a hack or similar tool. (g) "Rodding" means the dressing of the surface of revolving grindstone by the application of a rod, bar or strip of metal to such surface. 2. Exceptions.—(a) Nothing in this schedule shall apply to any factory in which only repairs are carried on except any part thereof in which one or more persons are wholly or mainly employed in the grinding or glazing of metals. (b) Nothing in this schedule except paragraph 4, shall apply to any grind-ng or glazing of metals carried on intermittently and at which no person is employed for more than 12 hours in any week. (c) The Chief Inspector may, by certificate in writing, subject to such conditions as he may specify therein, relax or suspend any of the provisions >f this schedule in respect of any factory, if owing to the special methods of work or otherwise such relaxation or suspension is practicable without danger :o the health or safety of the persons employed. 3. Equipment for removal of dust.—No racing, dry grinding or glazing hall be performed without— (a) a hood or other appliance so constructed, arranged, placed and maintained as substantially to intercept the dust thrown off; and (b) a duct of adequate size, airtight and so arranged as to be capable of carrying away the dust, which duct shall be kept free from obstruction and shall be provided with proper means of access for inspection and cleaning, and where practicable, with a connection at the end remote from the fan to enable the Inspector to attach thereto any instrument necessary for ascertaining the pressure of air in the said duct; and (c) a fan or other efficient means of producing a draught sufficient to extract the dust : Provided that the Chief Inspector may accept any other appliance that is in his opinion, as effectual for the interception, removal and disposal of dust thrown off as a hood, duct and fan would be. 4. Restriction on employment on grinding operations.—Not more than one person shall at any time perform the actual process of grinding or glazing upon a grindstone, abrasive wheel or glazing appliance : Provided that this paragraph shall not prohibit the employment of persons to assist in the manipulation of heavy or bulky articles at any such grindstone, abrasive wheel or glazing appliance. 5. Glazing.—Glazing or other processes, except processes, incidental to wet grinding upon a grindstone, shall not be carried on in any room in which wet grinding upon a grindstone is done. 6. Hacking and rodding.—Hacking or rodding shall not be done unless during the process either (a) an adequate supply of water is laid on at the upper surface of the grindstone, (b) adequate appliances for the interception of dust are provided in accordance with the requirements of paragraph 3. 7. Examination of dust equipment.—(a) AH equipment for the extraction or suspension of dust shall, at least once in every six months, be examined and tested by competent person, and any defect disclosed by such examination and test shall be rectified as soon as practicable. (b) A register containing particulars of such examination and test shall be kept in a form approved by the Chief Inspector. SCHEDULE VI Manufacture and Treatment of Lead and Certain Compounds of Lead 1. Exemptions.—Where the Chief Inspector is satisfied that all or any of the provisions of this schedule are not necessary for the protection of the persons employed, he may by certificate in writing, exempt any factory from all or any such provisions, subject to such condition as he may specify therein. 2. Definitions.—For the purposes of this schedule— (a) "Lead Compound" means any compound of lead other than galena which when treated in the manner described below, yields to an aqueous solution of hydrochloric acid, a quantity of soluble lead compound exceeding, when calculated as lead monoxide, five per cent of the dry weight of the portion taken for analysis. In the case of points and similar products and other mixture containing oil or fat the "dry weight" means the dry weight of the material remaining after the substance has been thoroughly mixed and treated with suitable solvents to remove oil, fats, varnish or other media. The method of treatment shall be as follows : A weighed quantity of the material, which has been dried at 100°C. and thoroughly mixed shall be continuously shaken for one hour, at the common temperature, with 1,000 times its weight of an aqueous solution of hydrochloric acid containing 0-25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filterate shall then be precipitated as lead sulphide and weighed as lead sulphate. (b) "Efficient exhaust draught" means localized ventilation effected by heat or mechanical means, for the removal of gas, vapour, dust or fumes so as to prevent them (as far as practicable under the atmospheric condition usually prevailing) from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove smoke generated at the point where such vapour, fumes or dust originate. 3. Application.—This schedule shall apply to all factories or parts of factories in which any of the following operations are carried on: (a) Work at a furnace where the reduction or treatment of zinc or lead ores is carried on. (b) The manipulation treatment or reduction of ashes containing lead, the desilvering of lead or the melting of scrap lead or zinc. (c) The manufacture of solder or alloys containing more than ten per cent of lead. (d) The manufacture of any oxide, carbonate, sulphate chromate, acetate, nitrate or silicate of lead. (e) Handling or mixing of lead tetraethyl. (f) Any other operation involving the use of a lead compound. (g) The cleaning of work-rooms where any of the operations aforesaid are carried on. 4. Prohibition relating to young young persons-No young person shall be employed or permitted to work in any of theoperations specified in paragraph 3.12 4-A CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed on permitted to work in any of the operations specified in paragraph 3 with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed on permitted to work at a bath. 5. Requirements to be observed.—No person shall be employed or permitted to work in any process involving the use of lead compounds, if the process is such that dust or fume from a lead compound is produced therein, or the persons employed therein are liable to be splashed with any lead compound in the course of their employment unless the provisions of paragraphs 6 to 14 are complied with. 6. Exhaust draught.—Where dust, fume, gas or vapour is produced in the process, provision shall be made for removing them by means of an efficient exhaust draught so contrived as to operate on the dust, fume, gas or vapour as closely as possible to the point of origin. 7. Certificate of fitness.—The person so employed has been granted by a Certifying Surgeon a certificate of fitness and such certificate is in the custody of the Manager of the factory. The certificate shall be kept readily available for inspection by any Inspector and the person granted such a certificate shall carry with him, while at work, a token giving reference to such certificate. 8. Medical examination.—(1) The person so employed shall be medically examined by a Certifying Surgeon within 14 days of his first employment in such process and thereafter shall be examined by Certifying Surgeon at intervals of not more than three months and a record of such examination shall be entered by 12 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 the Certifying Surgeon in the special certificate of fitness granted under paragraph 7. (2) If at any time the Certifying Surgeon is of opinion that any person is no longer fit for employment on the grounds that continuance therein would involve special danger to health, he shall cancel the special certificate of fitness of that person. (3) No person whose special certificate of fitness has been cancelled shall be employed unless the Certifying Surgeon, after re-examination again certifies him to be fit for employment. 9. Food, drinks, etc., prohibited in work-rooms.—No food, drink, pan and supari or tobacco shall be brought into or consumed by any worker in any work-room in which any of the processes specified in paragraph 3 are carried on and no person shall remain in any such room during intervals for meals or rest. 10. Protective clothing.—Suitable protective overalls and head coverings shall be provided, maintained and kept clean by the factory occupier and such overalls and head covering shall be worn by the persons employed. 11. Cleanliness of work-rooms, tools, etc.—The rooms in which the persons are employed and all tools, and apparatus used by them shall be kept in a clean state. 12. Washing facilities.—(1) The occupier shall provide and maintain for the use of all persons employed suitable washing facilities consisting of— (a) a trough with a smooth impervious surface fitted with a waste pipe without plug and of sufficient length to allow at least two feet for every ten persons employed at any one time, and having a constant supply of clean water from taps or jets above the trough at intervals of not more than two feet; or (b) at least one wash-basin for every ten persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of clean water; together with, in either case, a sufficient supply of nail brushes, soap or other suitable cleaning material and clean towels. (2) The facilities so provided shall be placed under the charge of a responsible person and shall be kept clean. 13. Mess-room or canteen.—The occupier shall provide and maintain for the use of the persons, employed suitable and adequate arrangements for taking their meals. The arrangements shall consist of the use of a room separate from any work-room which shall be furnished with sufficient tables and benches, and unless a canteen serving hot meals is provided, adequate means of warming food. The room shall be adequately ventilated by the circulation of fresh air, shall be placed under the charge of a responsible person and shall be kept clean. 14. Cloak-room.—The occupier shall provide and maintain for the use of persons employed, suitable accommodation for clothing not worn during working hours, and for the drying of wet clothing. SCHEDULE VII "Generation of Gas from Dangerous Petroleum 1. Prohibition relating to young persons-No young person shall be employed or permitted to work in or shall be allowed to enter any building in which the generation of gas from dangerous petroleum is carried on. 13 1A-CONDITION OF EMPLOYMENT OF WOMEN- Women workers may be employed or permitted to work in or shall be allowed to enter any building in which the generation of gas from dangerous petroleum is carried on with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as modernise the above possible, processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath. Provided further that no young person shall be employed or permitted to work at any operation of sand blasting. 2. Flame traps.—The plant for generation of gas from dangerous petroleum and associated piping and fittings shall be fitted with at least two efficient flame traps so designed and maintained as to prevent a flash back from any burner to the plant. One of these traps shall be fitted as close to the plant as possible. The plant and all pipes and valves shall be installed and maintained free from leaks. 3. Generating building or room.—AH plants for generation of gas from dangerous petroleum erected after the coming into force of the provision specified in this 13 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 schedule, shall be erected outside the factory building proper in a separate well ventilated building (hereinafter referred to as the "generating building"). In the case of such plant erected before the coming into force of the provisions specified in this schedule, there shall be no direct communication between the room where such plants are erected (hereinafter referred to "as the generating room") and the remainder of the factory building. So far as practicable, all such generating rooms shall be constructed of fire-resisting materials. 4. Fire extinguishers.—An efficient means of extinguishing petrol fires shall be maintained in any easily accessible position near the plant for generation of gas from dangerous petroleum. 5. Plant to be approved by Chief Inspector.—Petrol gas shall not be manufactured except in a plant for generating petrol gas the design and construction of which has been approved by the Chief Inspector. 6. Escape of petrol.—Effective steps shall be taken to prevent petrol from escaping into any drain or sewer. 7. Prohibition relating to smoking, etc.—No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in the generating room or building or in the vicinity thereof and warning notice in the language understood by the majority of the workers shall be posted in the factory prohibiting smoking and the carrying of matches, fire or naked light or other means of producing a naked light or spark into such room or building. 8. Access to petrol or containers.—No unauthorized person shall have access to any petrol or to a vessel containing or having actually contained petrol. 9. Electric fittings.—All electric fitting shall be of flame proof construction and all electric conductors shall either be enclosed in metal conduites or be lead- scheathed. 10. Construction of doors.—All doors in the generating room or building shall be constructed to open outward; or to slide and no door shall be locked or obstructed or fastened in such a manner that it cannot be easily and immediately opened from the inside while gas is being generated and any person is working in the generating room or building. 11. Repair of containers.—No vessel that has contained petrol shall be repaired in a generating room or building and no repairs to any such vessels shall be undertaken unless live steam has been blown into the vessel and until the interior thoroughly steamed out or other equally effective steps have been taken to ensure that it has been rendered free from petrol or inflammable vapour. SCHEDULE VIII Cleaning or Smoothing of Articles by a Jet of Sand, Metal Shot or Grit or other Abrasive propelled by a Blast of Compressed Air or Steam 1. Definition.—For the purpose of this schedule "Sandblasting" means the blasting of any articles by a jet of sand, metal shot, grit or other abrasive. 2. Sand blasting to be done in enclosed chamber.—Sand blasting shall not be done in any room except in an enclosed chamber or cabinet in which no other work is performed and at which efficient means are provided, arranged and maintained to prevent the escape of dust to the outside of such chamber or cabinet. 8. In the said Rules, in Schedule VIII, after paragraph 2, the following paragraph 2-A shall be inserted, namely:- 2-A-CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or permitted to work at any operation of sand blasting with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath.14 3. Prohibition relating to employment of women and young persons.—No women or young person shall be employed or permitted to work at any operation of sand blasting. 14 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 4. Protective equipment.—(1) Unless he is wearing a suitable protective helmet and gauntlets— (a) no person shall be employed or permitted to work at blasting in the open air or work within thirty feet of sand blasting apparatus in operation in the open air ; and (b) no person shall be employed or permitted to work or allowed in a blasting chamber whilst the sand blasting apparatus is in operation. (2) The occupier of the factory shall provide and maintain in good condition all helmets, overalls and gauntless, that are necessary to comply with the requirements of this schedule. (3) Every protective helmet shall carry the distinguishing mark of the person by whom it is to be used and shall be provided with a sufficient supply of pure air for breathing and ventilation, together with suitable arrangements to permit the escape of the expired air. (4) No person shall wear a protective helmet that has been worn by another person unless such protective helmet shall have been thoroughly disinfected. (5) All persons engaged in sand blasting while at work shall wear the protective equipment provided under the provisions of this paragraph. SCHEDULE IX Liming and Tanning of Raw Hides and Skins and Process Incidental thereto 1. Cautionary notices.—(1) Cautionary notices as to anthrax in the form specified by the Chief Inspector shall be affixed in prominent position in the factory where they may be easily and conveniently read by the person employed. (2) A copy of a warning notice as to anthrax in the form specified by the Chief Inspector shall be given to each person employed when he is engaged and subsequently if still employed, on the first day of each calendar year. (3) Cautionary notices as to the effects of chrome on the skin shall be affixed in prominent positions in every factory in which chrome solutions are used and such notices shall be so placed as to be easily and conveniently read by the persons employed. (4) Notices shall be affixed in prominent places in the factory stating the position of the "First-Aid" box or cupboards and the name of the person in charge of such box or cupboard. (5) If any person employed in the factory is illiterate, effective steps shall be taken to explain carefully to such illiterate person the contents of the notices specified in paragraphs 1, 2 and 4 and if chrome solutions are used in the factory, die contents of the notice specified in paragraph 3. 2. Protective clothing.—The occupier shall provide and maintain in good condition the following articles of protective clothing— (a) water-proof footwear, leg coverings, aprons and rubber gloves for persons employed in processes involving contact with chrome solutions including the preparation of such solutions; (b) protective foot-wear, aprons and gloves for persons employed in the handling of hides or skins other than in processes specified in clause (a) : Provided that gloves shall not be required for persons flashing by hand or where there is no risk of contract with lime, sodium sulphide or other caustic liquor. 3. Washing facilities, mess-room and cloak-room.—There shall be provided and maintained in a cleanly state and in good repair for the use of all persons employed— (a) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least two feet for every ten persons employed at any one time, and having a constant supply of water from taps or jets above the trough at intervals of not more than two feet; or (b) at least one wash basin for every ten such persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of water, together with, in either case, a sufficient supply of nail brushes, soap or other suitable cleaning materials and clean towels; (c) a suitable mess-room adequate for the number remaining on the premises during the meal intervals, which shall be furnished with (1) sufficient tables and benches and (2) adequate means for warming food and for boiling water; The mess-room shall (1) be separate from any room or shed in which hides or skins are stored, treated or manipulated, (2) be separate from the cloak-room, and (3) be placed under the charge of a responsible person; (d) suitable accommodation for the clothing not worn during working hours with adequate arrangements for drying the clothing, if wet. The accommodation so provided shall be placed under the charge of a responsible person. 4. Food, drinks, etc. prohibited in work-rooms.—No food, drinks, pan and supari or tobacco shall be brought into or consumed by any worker in any work-room or shed in which hides or skins are stored, treated or manipulated. 5. First-aid arrangements.—The occupier shall (a) arrange for an inspection of the hands of all persons coming in to contact with chrome solutions to be made twice a week by a responsible person ; (b) provide and maintain a sufficient supply of suitable ointment and impermeable waterproof plaster in a box readily accessible to the worker and used solely for the purpose of keeping the ointment and plaster. SCHEDULE X Certain lead process carried on Printing Presses and Type Foundries 1. Exemption.—Where the Chief Inspector is satisfied that all or any of the provisions of this Schedule are not necessary for the protection of persons employed, he may, by certificate in writing exempt any factory from all or any of such provisions subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector. 2. Definitions.—In these regulations— "Lead material" means material containing not less than five per cent of lead. "Lead process'15 means— (a) the melting of lead or any lead material for casting and mechanical composing; and (b) the re-charging of machines with used lead material, or (c) any other work including removal of dross from melting pots, cleaning of plungers; (d) manipulation, movement or other treatment of lead material. "Efficient exhaust draught" means localized ventilation effected by heat or mechanical means for the removal of gas, vapour, dust or fumes at the point where they originate so as to prevent them from escaping into the air of any place in which work is carried on. 3. Exhaust draught.—None of the following processes shall be carried on except with an efficient exhaust draught— (a) melting lead material or slugs ; (b) heating lead material so that vapour containing lead is given off; or, unless carried on in such a manner as to prevent free escape of gas, vapour, fumes or dust into any place in which work is carried on, or, unless carried on in electrically heated and thermostatically controlled melting pots. Such exhaust draught shall be effected by mechanical means and so contrived as to operate on the dust, fume, gas or vapour given off as clearly as may be at its point of origin. 4. Prohibition relating to young persons-No young person shall be employed or permitted to work in any lead process. 4A-CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or permitted to work in any lead process with their consent to work subject to the following conditions :- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath. 15 . 5. Separation of certain process.—Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another and from any other process— (a) melting of lead or any lead material; (b) casting of lead ingots; 15 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 (c) mechanical composing. 6. Container for dross.—A suitable receptacle with tightly fitting cover shall be provided and used for dross as it is removed from every melting pot. Such receptacle shall be kept covered while in the work-room near the machine except when the dross is being deposited therein. 7. Floor of work-room.—The floor of every work-room where lead process is carried on shall be— (a) of cement or similar material so as to be smooth and impervious to water; (b) maintained in sound condition ; and (c) shall be cleansed throughout daily after being thoroughly damped with water at a time when no other work is being carried on at the place. 8. Mess-room.—There shall be provided and maintained for the use of all persons employed in a lead process and remaining on the premises during the meal intervals, a suitable mess-room which shall be furnished with sufficient tables and benches. 9. Washing facilities.—There shall be provided and maintained in a clean state and in good repair for the use of all persons employed in a lead process— (a) a wash place with either— (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least two feet for every five such persons employed at any one time and having a constant supply of water from taps or jets above the trough at intervals of not more than 2 feet; or (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having and adequate supply of water laid on or always readily available; and (b) a sufficient supply of clean towels made of suitable material renewed daily with a sufficient supply of soap or other suitable cleansing material. 10. Medical examination.—(a) Every person employed in a lead process shall be examined by the Certifying Surgeon within fourteen days of his first employment in such processes and thereafter shall be examined by the Certifying Surgeon at intervals of not more than three months, and a record of examination shall be entered by the Certifying Surgeon in the health register in Form No. 17. (b) A health register containing names of all persons employed in any lead process shall be kept in Form No. 17. (c) If at any time the Certifying Surgeon is of opinion that any person is no longer fit for employment on any lead process, on the ground that his continuance in such employment will involve special danger to his health, he shall make an entry to this effect in the health register against the name of such person. No such person shall be employed on a lead process without the written sanction of the Certifying Surgeon, entered in the health register. 11. Food, drinks, etc. prohibited in work-rooms.—No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any work room in which any lead process is carried on. SCHEDULE XI DICHROMATE MANUFACTURE 1. Separation of certain processes.—Processes as indicated below which give rise to noxious dust, fume, vapour or mist should be isolated from others end should either be totally enclosed or provided with hoods with suitable axhaust ventilation arrangements where necessary— (i) Soda-mix section, including the place of storage of the mixed chro-mite soda- ash powder. (ii) Reacted frit storing. (iii) Frit dissolving. (iv) Evaporation of the dischromate solution. (v) Dichromate weighing and packing or otherwise handling of the dichromate powders. 2. Use of respirators.—In operations, which are of shorter duration and in which mechanical exhaust is not practicable, the occupier shall provide respirators for the use of workers. 3. Protective equipment.—There shall be provided for the use of all workers suitable footwear, gloves and aprons engaged in the following processes : (a) Acidification. (b) Concentration. (c) Centrifugalization. (d) Crystallization. (e) Packing. 4. Floor of work-rooms.—The floor of every work-room shall be— (a) of impervious material and allow of easy drainage, (b) maintained in sound condition, (c) kept free from materials, plank or other obstruction not required for or produced, in the process carried on in the room. 5. Cloak-room.—There shall be provided and maintained for the use of all persons employed in dichromate department a cloak-room for clothing put off during working hours. 6. Washing facilities.—There shall be provided and maintained in a clean state and a good repair, for the use of all persons employed in dichromate process— (a) trough with an impervious surface fitted with a waste pipe without plug and of sufficient length to allow at least two feet for every ten persons employed at any one time and having a constant supply of clean water from taps or jets above the trough at intervals of not more than two feet, or (b) at least one wash basin for every ten persons employed at any one time fitted with a waste pipe and plug and having a constant supply of clean water; together with, in either case, sufficient supply of soap or other suitable cleansing material and clean towels. 7. Medical requisites.—The occupier shall provide and maintain a sufficient supply of suitable protective skin cream and nasal ointment, readily available to the workers engaged on dichromate processes at the discretion of the Certifying Surgeon. 8. Medical examination.—Every person employed in a dischromate process shall be examined by the Certifying Surgeon within fourteen days of his first employment in such processes and thereafter shall be examined by the Certifying Surgeon at intervals of not more than three months and a record of each examination shall be entered by the Certifying Surgeon in the Health Register in Form No. 17. (2) A Health Register containing names of all persons employed in any dichromate process shall be kept in Form No. 17. (3) If any time the Certifying Surgeon is of opinion that any person is no longer fit for employment on any dichromate process, on the ground that his continuance in such employment will involve special danger to his health he shall make an entry to this effect in the Health Register against the name of such person. No such person shall be employed on dichromate process without the written sanction of the Certifying Surgeon, entered in the Health Register. 9. Cautionary notices.—Cautionary notices on the nature of health hazards involved together with the control measures for their protection shall be fixed at a prominent position of the factory. SCHEDULE XII Chemical Works Application.—The provisions of this Schedule shall apply to all manufactures and processes incidental thereto carried on in Chemical Works. These provisions shall be in addition fo and not in derogation of any provisions of the Factories Act or any other rules made thereunder or of any other Act or Rules. Definitions : Chemical works means any factory or such parts of any factory as are named in sub-schedule A of this Schedule. Breathing apparatus means (1) a helmet or facepiece with necessary connections by means of which a person using it in a poisonous, asphyxiating or irritant atmosphere breaths ordinary air, or (2) any other suitable apparatus approved in writing by the Chief Inspector. Life-belt means a belt made of leather or other suitable material which can be securely fastened round the body with a suitable length of rope attached to it, each of which is sufficiently strong to sustain the weight of a man. Efficient exhaust draught means localized ventilation effected by mechanical or other means for the removal of gas, vapour, fume, or dust to prevent it from escaping into the air of any place in which work is carried on. Surgeon means a Certifying Surgeon appointed under Section 10 of the Factories Act, 1948. Suspension means suspension by written certificate in the Health Register, signed by the Surgeon from employment in any process mentioned in the certificate. Bleaching powder means the bleaching powder commonly called chloride of lime. Chlorate means chlorate or perchlorate. Caustic means hydroxide of potassium or sodium. Caustic pot means a metal pot fixed over a furnace or flue and surrounded by brickwork, such as is commonly used for concentrating caustic liquor, whether such pot be used for concentrating or boiling caustic or other liquor. Chrome process means the manufacture of chromate or bichromate of potassium or sodium, or the manipulation, movement or other treatment of these substances in connection with their manufacture. Nitro or amino process means the manufacture of nitro or amino derivatives of phenol and of benzene or its homologues and the making of explosives with the use of any of these substances. Exceptions.—If the Chief Inspector is satisfied in respect of any factory or any process that, owing to the special conditions or special methods of work, or by reason of the infrequency of the process or for other reasons, all or any of the requirements of the provisions of this Schedule are not necessary for the protection of persons employed in any factory or process, he may by order in writing (which he may in his discretion revoke), exempt such factory or process from all or any of the provisions of this Schedule, subject to such conditions as he may by such order prescribe. PART I—APPLYING TO ALL THE WORKS IN SUB-SCHEDULE A General 1. House-keeping.—(a) Every part of the ways, works, machinery and plant shall be maintained in a clean and tidy condition. (b) any spillage of material shall be cleaned up without delay. (c) Floors, platforms, stairways, passages and gangways shall be kept free of temporary obstructions. (d) There shall be provided easy means of access to all parts of the plant to facilitate cleaning, maintenance and repairs. 2. Improper use of chemicals.—(a) No chemicals or solvents shall be used by workers for any purposes apart from the process for which they are supplied. (b) Workers shall be instructed on the possible dangers arising from such misuse. These instructions shall further be displayed in bold letters in prominent places in die different sections. 3. Storage of food.—(a) No food, drink, tobacco, pan or similar articles shall be stored or consumed on or near any part of the plant. (b) Testing.—Workers shall be instructed on the possible dangers arising from the testing of materials, or of the use for drinking purposes of any vessel used in, or in connection with, the manufacture of chemicals. These instructions shall further be displayed in bold letters in prominent places in the different sections. 4. Process hazards.—Before commencing any large scale experimental work, or any new manufacture, all possible steps shall be taken to ascertain definitely all the hazards involved both from the actual operations and the chemical reactions. The properties of the raw materials used, the final products to be made, and any bye-products arising during manufacture, shall be carefully studied and provision shall be made for dealing with any hazards including effects on workers, which may arise during manufacture. The design of the building and plan shall be based on the information so obtained. 5. Unauthorized personnel.—(a) Unauthorized persons shall not be permitted to enter any section of the factory or plant where these are special dangers. (b) Visitors.—Visitors shall be provided, where necessary with suitable safety equipment and shall be accompanied round dangerous plant by a responsible official. 6. Instruments.—All instruments such as pressure gauges, thermometers, flow meters and weighing machines shall be tested at regular intervals by a competent person, and records of these tests shall be kept in a register. 7. Cocks and valves.—Suitable valves shall be provided in all service lines at sufficiently short intervals for convenience in blanking off, etc. All cocks and valves shall be operated at least once a month, and tested periodically by a competent person, and records of these tests shall be kept in a register. A plan of all service installations shall be kept readily available for perusal. 8. Manholes.—No manholes shall be opened for entry until effective fencing has been erected round it. 9. Emergency instructions.—Simple and special instructions shall be trained to ensure that effective measures will be carried out in cases of emergency to deal with escape of inflammable, poisonous or deleterious gases, vapours, liquids or dusts. These instructions shall further be displayed in bold letters in prominent places in the different sections. All workers shall be trained and instructed in the action to be taken in such emergencies, and in the general hazards of their employment. 10. Protection of reaction mixtures.—Suitable arrangements shall be made to ensure that no foreign matter of any sort can fall into reaction mixtures. 11. Electrical apparatus.—Electrical plant, fittings and conductors shall, if exposed to a damp or corrosive atmosphere, be adequately protected. Periodic tests shall be carried out on all circuits. 12. Places of work.—(a) Workers shall only be allowed in those places in which they have been given orders to work. (b) In dangerous sections of a factory, the number of workers shall be kept to a minimum compatible with the process. 13. Packing, storage and transport of chemicals.—Chemicals shall be packed and stored in containers suitable for the purpose and of adequate strength for storage or transport. All such containers shall be suitably labelled so that they may be stored and transported in such a manner as to ensure that, in the event of spillage, they will neither produce a reacting mixture, nor cause the development of toxic or fire risk in contract with other products in its vicinity or with walls, floors or dust thereon. Fire and Explosion Risks 14. Site.—(a) Buildings and plant shall be located with due regard to the dangers which may arise from the process involved, and in particular shall be spaced at distances which are deemed safe for the fire and explosive risks connected with the processes in adjacent buildings. Due consideration shall be given to the effect on any processes carried out in adjacent factories. (b) Isolation of buildings.—Where special dangers exist, separate buildings shall be used for the different parts of a process. They shall be spaced at sufficient distances apart and shielded to prevent damage to each other in the event of fire or explosion, and shall be safeguarded by the provision of suitable blowout panels or roofs. Where the risk of fire or explosion is considerable, the building shall be divided by blast or protective screen walls. (c) Fire resistance.—No combustible materials shall be used in the erection of working buildings, unless there are special reasons necessitating their use, when they shall be rendered fire-resistance. The roof shall be of light fire-resistant construction and floors shall be of impervious fire-resistant material and shall be regularly maintained in such condition. 15. Dangers of ignition (including building installation).—(a) No internal combustion engine and no electric motor or other electric equipment, capable of generating sparks or otherwise causing combustion shall be installed or used in a building or danger zone. Electric conductors shall be fitted with screwed steel conduit. (b) All hot exhaust pipes shall be installed outside a building and other hot pipes shall be suitably protected. (c) Portable electric hand lamps shall not be used unless of an intrinsically safe type, and portable electric tools connected by flexible wires shall not be used, unless of the flames proof type. (d) Where an inflammable atmosphere may occur the soles of footwear worn by workers shall have no metal on them, and the wheels of trucks or conveyers shall be of conducting non-sparking materials. Adequate precautions shall be taken to prevent the ignition of explosive or inflammable substances by sparks emitted from locomotives or other vehicles operated in the factory or on public lines. (e) No electric arc lamps or naked light, fixed or portable, shall be used, and no person shall have in his possession any match or any apparatus of any kind for producing a naked light of sparking in or on, or about any part of the factory where there is liability to fire or explosion from inflammable gas, vapour or dust and all incandescent electric lights in such parts shall be in double air-tight glass covers. (f) Prominent notices in the language understood by the majority of the workers and legible by day and by night prohibiting smoking, the use of naked lights and the carrying of matches or any apparatus for producing a naked light or spark, shall be affixed at die entrance of every room or place where there is the risk of fire or explosion from inflammable gas, vapour or dust. In the case of illiterate workers the contents of the notices shall be fully and carefully explained to them when they commence work in the factory for the first time and again when they have completed one week at the factory. (g) Non-sparking tool.—A sufficient supply of spades, scraper and pails made from non-sparking material shall be provided for the use of persons employed in cleaning out or removing residues from any chamber, still, tank or other vessel where an inflammable or explosive danger may occur. 16. Static electricity.—(a) All machinery and plant, particularly, pipe lines and belt drives, on which static electricity is likely to accumulate, shall be effectively earthed. Receptacles for inflammable liquids shall have metallic connections to the earthed supply tanks to static sparking. Where necessary, humidity shall be controlled. (b) Mobile tank wagons shall be earthed during filling and discharge, and precautions shall be taken to ensure that earthing is effective before such filling or discharge takes place. (c) Lightning conditions.—Lightning protection apparatus shall be fitted where necessary and shall be maintained in good condition. 17. Process heating.—The method of providing heat for a process shall be as safe as possible and where the use of naked flame is necessary, the plant shall be so constructed as to prevent any escaping inflammable gas, vapour or dust coming into contact with the flame, or exhaust gases or other hot agency likely to cause ignition. So far as practicable, the heating medium shall be automatically controlled at a pre-determined temperature below the danger temperature. 18. Escape of materials.—(a) Provision shall be made in all plants, sewers, drains, flues, ducts, culverts, and buried pipes to prevent the escape and spread of any liquid gas, vapour, fume or dust likely to give rise to fire or explosive, both during normal working and in the event of accident or emergency. (b) If escape occurs, such substances shall be removed expeditiously and efficiently at the point of liberation. The effluent shall be trapped and rendered safe outside the danger area. 19. Leakage of inflammable liquids.—(a) Provision shall be made to confine by means of bund-walls, sumps, etc., possible leakages from vessels containing inflammable liquids. (b) Adequate and suitable fixed fire-fighting appliances shall be installed in the vicinity of such vessels'. 20. Cleaning of empty containers.—(a) All empty containers which have held inflammable liquids, and metal containers which have held sulphuric acid shall be rendered permanently safe as soon as practicable, and shall not be repaired or destroyed until such cleaning has been completed. (b) Storage of combustible materials.—Combustible and inflammable materials shall not be stored in close proximity to chemicals which are liable to cause ignition. (c) Rubbish shall be removed from buildings without delay and placed in special metal containers provided with close fitting lids. The contents shall be removed daily and suitably dealt with. Waste products containing inflammable or explosive materials shall not be placed on rubbish heaps but shall be destroyed in an appropriate manner. 21. Installing of pipe lines for inflammable liquids.—All pipe lines for the transport of inflammable liquids shall be protected from breakage, shall be arranged so that there is no risk of mechanical damage from vehicles and shall be so laid that they drain throughout without the collection of any part. All flanged joints, bends and other connections shall be regularly inspected. Cocks and valves shall be so constructed that explosive residues do not get accumulated therein. The open and closed positions of all cocks and valves shall be clearly indicated on the outside. 22. Packing of reaction vessels.—Packing and jointing materials for reaction vessels (including covers, manhole covers and exhaust pipes) and in pipe lines and high or low temperature insulating materials, shall not contain materials which are combustible or which react with the products of the plant. 23. Safety valves.—Every still and every closed vessels in which gas is produced or into which gas is passed and in which the pressure is liable to rise to a dangerous degree shall have attached to it a pressure gauge, and a proper safety valve or other equally efficient means to relieve the pressure, maintained in good condition. Nothing in this Schedule shall apply to metal bottles or cylinders used for the transport of compressed gases. 24. Vigorous or delayed reactions.—Suitable provision, such as automatic and distant control shall be made for controlling the effects of unduly vigours or delayed reactions. Automatic flooding or blanketing shall be provided for in the event of an accident. 25. Examination, testing and repair of plant.—Examination, testing and repair of plant parts which have been in contact with explosive and inflammable material, or which is under pressure, shall only be carried out under proper supervision. 26. Alarm system.—(a) Gravity or pressure feed systems of supplying inflammable materials to the various parts of the buildings or plant shall be fitted with alarm systems, automatic cut-offs or other devices to prevent overcharging or otherwise endangering the plant. (b) The amount of inflammable material taken into a building in bulk containers at any one time shall be kept as low as practicable. (c) Adequate steps shall be taken to prevent the escape of inflammable and explosive vapours from any container into the atmosphere of any building. Gas, Vapour, Fume or Dust Risks 27. Escape of gases, etc.—Effective steps shall be taken to prevent the escape of dangerous gases, vapours, fumes or dust from any part of the plant, by the total enclosure of the process involved or by the provisions of efficient exhaust draught. Effective arrangements shall be made to ensure that in the event of a failure of the control measure, the process shall stop immediately. Further arrangements shall be made to ensure that in case there is any such escape, the material shall be trapped forthwith so that the danger may be averted. 28. Danger due to effluents.—(a) Adequate precautions shall be taken to prevent the mixing of effluents which may produce dangerous or poisonous gases. (b) Effluents, which may contain or give rise in the presence of other effluents to such gases, shall be provided with independent drainage systems to ensure that they may be trapped and rendered safe. 29. Staging.—(a) Staging shall not be erected over any open vessel unless the vessel is so constructed and ventilated as to prevent the omission of vapour or fumes about such staging. (b) Where such staging is provided to give access to higher levels in large plants, effective means shall be provided at all levels with direct means of access to the outside of the room or building and thence to ground level. (c) Such staging shall be fitted with suitable handrails and toeboards, and the floors and staging shall be impervious and easily cleaned. 30. Instructions as regards risk.—Before commencing work, every worker shall be fully instructed on the properties of the materials they have to handle, and of the dangers arising from any gas, fume, vapour or dust which may be evolved during the process. Workers shall also be instructed in the measures to be taken to cope with any emergency. 31. Breathing apparatus.—(a) There shall be provided in every factory where dangerous gas or fume is liable to escape a sufficient supply of— (i) breathing apparatus of an approved make for the hazards involved ; (ii) oxygen and suitable means of its administration; and (tit) life-belts. The breathing apparatus and other appliances required by this Schedule shall (i) be maintained in good order and kept in an ambulance room or in some other place approved in writing by the Chief Inspector, and (ii) be thoroughly inspected once every month by a competent person, appointed in writing by the occupier and record of their condition shall be entered in a book provided for that purpose, which shall be produced when required by an Inspector. (b) Workers shall be trained and given a periodic refresher course in the use of breathing apparatus and respirators. (c) Respirators shall be kept properly labelled in a clean dry light-proof cabinets, and if liable to be affected by fumes, shall be protected by suitable containers. Respirators shall be dried and cleaned after use and shall be periodically disinfected. 32. Treatment of persons.—In every room or place wherever required in writing by the Chief Inspector there shall be affixed the official cautionary notice regarding gasing and burns. Such notices shall be legible by day and by night and shall be printed in the language understood by the majority of the workers. 33. Personal protective equipment.—(a) Suitable protective clothing shall be provided for the use of operatives; (i) when operating valves or cocks controlling fluids which by their nature, pressure or temperature would be highly dangerous if a blow-out occurred or when, cleaning chokes in system containing such fluids if pressure is likely to exist behind that chokes, (ii) when there is danger of injury absorption through the skin during the performance of normal duties or in the event of emergency, (iii) whenever there is the risk of injury in handling corrosive substances, hot or cold articles and sharp or rough objects, and (iv) when there is the risk of poisonous material being carried away on their clothes. (b) There shall be provided for the use of all persons employed in the processes specified in sub-schedule B of this Schedule an adequate supply of suitable protective equipment including gloves, overalls and protective footwear, and of goggles and respirators. Respirators shall be of a type approved in writing by the Chief Inspector. (c) Protective equipment shall be provided and stored in the appropriate place for use during abnormal conditions or in an emergency. (d) Arrangements shall be made for the proper and efficient cleaning of all such protective equipment. 34. Cloak-rooms.—There shall be provided and maintained for the use of all persons employed in the processes specified in sub-schedule B of this Schedule a suitable cloak-room for clothing put off during working hours and a suitable place separate from the cloak-room, for the storage of overalls or working clothes. The accommodation so provided shall be placed in the charge of a responsible person, and shall be kept clean. 35. Special bathing accommodations.—(a) There shall be provided for the use of all persons employed in the processes specified in sub-schedule C of this Schedule separate sanitary conveniences, and sufficient and suitable bathing facilities which shall be to the satisfaction of the Chief Inspector. (b) A bath register shall be kept containing the names of all persons employed in these processes and an entry of the date when each person takes a bath. 36. Entry into vessels.—(a) Before any person entries, for any purposes except that of rescue, any absorber, boiler, culvert, drain, flue, gas purifier, sewer, still tank, tower, vitriol chamber or other place where there is reason to apprehend the presence of dangerous gas or fume, a responsible person appointed in writing by the occupier for the purpose, shall personally examine such place and shall certify in writing in a book kept for the purpose either that such place is isolated and sealed from every source of such gas or fume and is free from danger, or that it is not so isolated and sealed and free from danger. No person shall enter any such place which is certified not to be so-is olated and sealed and free from danger unless he is wearing a breathing apparatus, and (where there are no cross stays or obstructions likely to cause entanglement) a life-belt, the free end of the rope attached to which shall be left with a man outside, whose sole duty shall be to keep watch and to draw out the wearer if he appears to be affected by gas or fume. The belt and rope shall be so adjusted and worn that the wearer can be drawn up head foremost through any manhole or opening. (b) A person entering, for the purpose of rescue, any such place for which a clearance certificate has not been issued shall wear breathing apparatus and life- belt in the manner specified. 37. Examination and repair of plant.—Where poisonous materials are likely to be present, the examination and repair of plant and piping shall only be done under the supervision of a competent person, and after the plant and piping has been thoroughly cleaned and ventilated. When opening vessels and breaking joints in pipe lines, respirators, goggles and protective clothing shall be worn to the extent required by the competent person. 38. Storage of acid carboys.—Carboys containing nitric acid or "mixed''' acid shall be stored in open-sided sheds detached from other buildings, and placed on a flooring of sandstone, brick or other suitable inorganic material. A passage-way shall be provided and kept free from obstruction between every four rows of such carboys. An ample supply of water shall be available for washing away spilt acid and all precautions shall be taken to prevent workers being exposed to fumes. Corrosive or Deleterious Risk 39. Buildings.—All buildings and plants shall be located with due regard to possible dangers from accidental liberation or splashing of corrosive and deleterious liquids, and shall be so designed as to facilitate through washing and cleaning. The construction of staging and other parts of buildings shall be carried out with materials impervious and resistant to corrosion so far as practicable. 40. Leakage.—(a) All plants shall be so designed and constructed as to obviate the escape of corrosive liquid. Where necessary, separate buildings, rooms or protective structures shall be used for the dangerous stages of the process and the buildings shall be so designed as to localize any escape of liquid. (b) Catch-pits, bund walls or other suitable precautions shall be provided to restrict the serious effects of such leakages. Catch-pits shall be placed below joints in pipe lines where there is danger involved from such leakage. (c) Passages and work station shall not be situated directly below any part of plant where there is risk of escape of dangerous liquid. Access to such parts shall, so far as practicable, be prohibited and danger notices shall be affixed at suitable points. 41. Precautions against escape.—Adequate precautions shall be taken to prevent the escape of corrosive or deleterious substances and means shall be provided for rendering safe any such escape. 42. Drainage.—Adequate drainage shall be provided and shall lead to special treatment tanks where deleterious materials shall be neutralized or otherwise rendered safe before it is discharged into ordinary drains or sewers. 43. Covering of vessels.—(a) Every fixed vessel or structure containing any dangerous materials, and not so covered as to eliminate all reasonable risk of accidental immersion in it of any portion of the body of a worker, shall be so constructed that there is no foothold on the top or the sides. (b) Such vessel shall, unless its edge is at least three feet above the adjoining ground or platform be securely fenced to a height of at least three feet above such adjoining ground or platform. (c) No plank or gangway shall be placed across or inside any such vessel, unless such plank or gangway is at least 18 inches wide, and is securely fenced on both sides by rails spaced at 9 inches apart to a height of at least 3 feet, or by other equally efficient means. (d) Where such vessels adjoin and the space between them, clear of any surrounding brick or other work, is either less than 18 inches in width or is 18 or more inches in width, but is not securely fenced on both sides to a height of at least three feet, secure barrier shall be so placed as to prevent passage between them : Provided that sub-paragraph (b) above shall not apply to— (i) Saturators used in the manufacture of sulphate of ammonia, (it) that part of the sides of brine evaporating pans which require raking, drawing or filling. 44. Ventilation.—Adequate ventilation shall be provided and maintained at all times in rooms or buildings where dangerous gas, vapour, fume or dust may be evolved. 45. Means of escape .—Adequate means of escape from rooms or buildings in the event of a leakage of corrosive liquid shall be provided and maintained. 46. Treatment of personnel.—In all places where (strong acids or dangerous) corrosive liquids are used : (a) There shall be provided for use in an emergency— (i) adequate and readily accessible means of drenching with cold water persons, and the clothing of persons, who have become splashed with such liquids; (ii) adequate special arrangements to deal with any person who has been splashed with poisonous material that can be absorbed through the skins; (iii) a sufficient number of eyewash bottles, filled with distilled water or other suitable liquid, kept in boxes or cupboards conveniently situated and clearly indicated by a distinctive sign which shall be visible at all times. (b) Except where the manipulation of such corrosive liquids is so carried on as to prevent risk of personal injury from splashing or otherwise, there shall be provided for those who have to manipulate such liquids sufficient and suitable goggles and gloves or other suitable protection for the eyes and hands. If gloves are provided they shall be collected, examined and cleansed at the close of the day's work and shall be repaired or renewed when necessary. 47. Maintenance.—(a) Before any examination or repairs are carried out or plant or pipe lines, a competent person shall issue a clearance certificate permitting-such examination or repairs. (b) Adequate precaution shall be taken to liberate any pockets of gas or liquid which may have been formed in pipe lines and which may cause corrosive spray at the point where dismantling takes place. 48. Washing facilities.—(1) There shall be provided and maintained in every factory for the use of employed persons adequate and suitable facilities for washing which shall include soap and nail brushes or other suitable means of cleaning and facilities shall be conveniently accessible and shall be kept in a clean and orderly condition. (2) If female workers are employed, separate washing facilities shall be provided and so enclosed or screened that the interiors are not visible from any place where persons of the other sex work or pass. The entrance to such facilities shall bear conspicuous notice in the language understood by the majority of the workers "for women only" and shall also be indicated pictorially. 49. Mess-room facilities.—In every factory there shall be provided and maintained for the use of those remaining on the premises during the rest intervals, suitable and adequate mess-room or canteen accommodation which shall be furnished with sufficient tables and chairs or benches with back rests and where sufficient drinking water is available. 50. Ambulance Room.—(a) In every factory in which more than 250 persons are employed on the processes to which this Schedule applies, there shall be provided and maintained in good order an Ambulance Room. The Ambulance Room shall be a separate room used only for the purpose of treatment and rest. It shall have a floor space of not less than 100 square feet and smooth, hard and impervious walls and floor, and shall be provided with ample means of natural and artificial lighting. It shall contain all the items shown in sub-schedule D. Where person of both sexes are employed, arrangements shall be made at the Ambulance Room for their separate treatment. The Ambulance Room shall be placed under the charge of a qualified nurse or other person trained in First Aid, who shall always be readily available during working hours, and shall keep a record of all cases of accidents or sickness treatment in the room. (b) In every factory there shall be provided and maintained in good condition a suitably constructed ambulance van for the purpose of the removal of serious cases of accident or sickness unless arrangement have been made with a hospital or other place in telephonic communication with the factory for obtaining such a carriage immediately when required. 51. Medical personnel.—There shall be a wholetime Medical Officer in every factory employing 250 persons or more. 59[52. Medical examination.—Workers engaged in the manufacture, processing, formulation or use of the following, shall be examined once in three months by the Certifying Surgeon and records maintained : (i) Hexaethyl tetra phosphate. (ii) Tetraethyl pyrophosphate. (iii) O. O. Diethyl O-P nitrophynyl thiophosphate (Parathion). (iv) Nicotine, nicotine sulphate. (v) Mercury derivatives. (vi) Methyl bromide, (vii) Cyanides. (viii) Arsenical derivatives. (ix) Chrome process compounds. (x) Nitro or amino process compounds. (a) A Health Register containing the names of all workers so engaged shall be kept in a form approved by the Chief Inspector. (b) No person shall be so engaged newly for more than fourteen days without a certificate of fitness granted after examination by the Certifying Surgeon, by a signed entry in the Health Register. (c) Every person so engaged newly shall present himself at the appointed time for examination by the Certifying Surgeon as provided in (b) above. (d) The Certifying Surgeon shall have power of suspension as regards all persons so engaged and no persons after suspension shall be so engaged without written sanction from the Surgeon entered in the Health Register.] 53. Duties of workers.—Every person employed shall— (a) report to his foreman any defect in any fencing, breathing apparatus, appliances or other requisite provided in pursuance of this Schedule as soon as he becomes aware of such defect; (b) used the articles, appliances or accommodations required by this Schedule for the purpose for which they are provided; (c) wear the breathing apparatus and life-belt where required under Paragraph 36 (a) and (b) above. 54. No person shall.—(a) Remove any fencing provided in pursuance of Paragraph 43 unless duly authorised ; or (b) stand on the edge or on the side of any vessel to which Paragraph 43 applies; (c) pass or attempt to pass any barrier created in pursuance of Paragraph 43 ; (d) place across or inside any vessel to which Paragraph 43 applies, any plank or gangway which does not comply with that Regulation or make use of any such plan or gangway while in such position; (e) take a naked light or any lamp or matches or any apparatus for producing a naked light or spark into or smoke in, any part of the works where there is liability to explosion from inflammable gas, vapour or dust; (f) use a metal spade, scraper or pail when cleaning out or removing the residues from any chamber, still tank, or other vessel wherein were contained sulphuric acid or hydrochloric acid or other substance which might cause evolution of arseniuretted hydrogen; and (g) removes from a First Aid Box or cupboard or from the Ambulance Room any First Aid appliance or dressing except for that treatment of injuries in the works. SUB-SCHEDULE "A" "Chemical work* means any work or part of a work in which: 1. The manufacture or recovery of any of the following is carried on— (a) Carbonates, cromates, chlorates, oxides or hydroxides or potassium, sodium, iron, aluminium, cobalt, nickle, arsenic, antimony, zinc or magnesium; (b) Ammonium and the hydroxide and salts of ammonium; (c) Sulphurous, sulphuric, nitric, hydrochloric, hydro-fluoric, hydriodic, hydrosulphuric, boric, phosphoric, oxalic, arsenious, arsenic, lactic, acetic, tartaric or citric acids and their metallic or organic salts; and (d) Cyanogen compounds. 3. A wet process is carried on— (a) for the extraction of metal from one or from any by-product or residual material; or (b) in which electrical energy is used in any process of chemical manufacture. 3. Alkali waste or the drainage therefrom is put to any chemical process for the recovery of sulphur or for the utilization of any constituent of such waste or drainage. 4. Carbon bisulphide is made or hydrogen sulphide is evolved by the decomposition of metallic sulphides or hydrogen sulphide is used in the production of such sulphides. 5. Bleaching powder is manufactured or chlorine gas is made or is used in any process of chemical manufacture. 6. (a) Gas tar or coaltar or any compound product or residue of such tars is distilled or is used in any process of chemical manufacture. (b) Synthetic colouring matters for their intermediates are made. 7. Refining of crude shale oil or any process incidental thereto is carried out. 8. Nitric acid is used in the manufacture of nitro compounds. 9. Explosives are made with the use of nitro compounds. 10. Insecticides which may be phosphorous nicotine, mercury, naphthalene, cyanogen, arsenic, flourine, copper benzene and ethane compounds or derivative and methyl bromide are manufactured, mixed, blended and packed. SUB-SCHEDULE "B" 1. A nitro or amino process (overalls or suits of working clothes and protective footwear). 2. Grinding raw-materials in a chrome process (overall suits). 3. The crystal department and in packing a chrome process (protective coverings). 4. Packing in a chrome process (respirators). 5. Any room or place in which chlorate is crystallised, ground or packed (clothing of woollen materials and boots or overshoes, the soles of which have no metal on them). 6. Any room in which caustic is ground or crushed by machinery (goggles and gloves or other suitable protection for the eyes and hands). 7. Bleaching powder chambers or in packing charges drawn from such chambers (suitable respirators). 8. Drawing off of molten sulphur from sulphur pots in the process of corban disulphide manufacture (overalls, face-shield, gloves and footwear of fire-proof materials). 9. (a) Manufacture, mixing, blending and packing of insecticides which are phosphorous, nicotine, naphthalene, cyanogen, arsenic, fluorine, mercury and copper compounds or derivatives and methyl bromide (rubber, aprons, chemical type goggles and suitable respirators and in addition rubber gloves and boots for phosphorous and nicotine derivatives, synthetic rubber aprons, gloves and boots when working with oil solutions and washable, working clothing laundered daily). (b) Manufacture, mixing, blending and packing of insecticides which are derivatives of benzene or ethalene (rubber aprons and suitable respirators, separate work clothes laundered frequently). SUB-SCHEDULE "C" 1. A nitro or amino process. 2. The crystal department and the packing room in a chrome process. 3. The process of distilling, gas or coaltar (other than blast furnace tar) and any process of chemical manufacture in which such tar is used. 4. The manufacture, mixing, blending and packing of the insecticides mentioned in sub-schedule "A". SUB-SCHEDULE "D" (i) A glazed zinc with hot and cold water always available; (ii) a table with a smooth top; (iii) means for sterilising instruments; (iv) a couch; (v) a stretcher; (vi) two buckets or containers with close fitting lids ; (vii) two rubber hot water bags ; (viii) a kettle and spirit stove or other suitable means of boiling water; (ix) twelve plain wooden splints 36"x4"x¼" ; (x) twelve plain wooden splints 4"x3"x¼"; (xi) six plain wooden splints, 10"x2"x½"; (xii) three woollen blankets ; (xiii) one pair artery forceps ; (xiv) one bottle of brandy ; (xv) two medium size sponges; (xvi) three hand towels ; (xvii) two kidney trays ; (xviii) four carbolic soaps ; (xix) two glass tumblers and two wine glasses; {xx) two clinical thermometers; (xxi) graduated measuring glass with teaspoon; (xxii) one eyebath; (xxiii) one bottle (2 lb.) carbolic lotion, 1 in 20; (xxiv) two chairs ; (xxv) one screen; (xxvi) one electric hand torch; (xxvii) an adequate supply of anti-tetanus serum; and (xxviii) two first aid boxes, each containing— (a) 24 small sterilized dressings ; (b) 12 medium size sterilized dressings ; (c) 12 large size sterilized dressings; (d) 12 large size sterilized burn dressings; (e) 12 half ounce packets sterilized cotton wool; (f) one snake bite lancet; (g) one pair scissors ; (h) two (1 oz.) bottles of potassium permanganate crystals; (i) one (4 oz.) bottle containing a two per cent alcoholic solution of iodine; (j) one (4 oz.) bottle of salvolatile having the dose and mode of administration indicated on the label; (k) a copy of the first aid leaflet issued by the Chief Adviser of Factories, Government of India. PART II Applying to work or parts thereof in which— (i) Caustic pots are used; or (ii) Chlorate of bleaching powder is manufactured ; or (iii) (a) gas tar or coaltar is distilled or is used in any process of chemical manufacture; or (b) nitro or amino process is carried on ; or (c) a chrome process is carried on ; or (iv) crude shale oil is refined or processes incidental thereto are carried on; or (v) nitric acid is used in the manufacture of nitro compounds; (vi) the evaporation of brine in open pans and the stoving of salt are carried on ; (vii) the manufacture or recovery of hydroflouric acid or any of its salts is carried on, (viii) work at a furnace where the treatment of zinc ores is carried on ; and (ix) insecticides mentioned in sub-schedule "A" are manufactured, mixed, blended or packed. 1. Entry into gas tar or coaltar still.—(1) Before any person enters a gas tar or coaltar still for any purpose except that of rescue, it shall be completely isolated from adjoining tar stills, either by disconnecting— (a) the pipe leading from the swan neck to the condenser worm ; or (b) the waste gas pipe fixed to the worm or receiver; and in addition, blank flanges shall be inserted between the disconnected parts, and the pitch discharge pipe or cock at the bottom of the still shall be disconnected. y' 2. Entry into bleaching powder chambers.—No person shall enter a chamber for the purpose of withdrawing the charge of bleaching powder unless and until— (i) the chamber is efficiently ventilated ; and (ii) the air in the chamber has been tested and found to contain not more than 2.5 grains of free chlorine gas per cubic foot. A register containing details of all such tests shall be kept in a form approved by the Chief Inspector. 3. Special precautions for a nitro and amino processes.—In nitro or amino process : (a) if crystallised subtances are broken or any liquor agitated by hand, means shall be taken to prevent as far as practicable, the escape of dust or fume into the air of any place in which any person is employed. The handles of all implements used in the operations shall be cleaned daily; (b) cartridges shall not be filled by hand except by means of a suitable scope; (c) every drying stove shall be efficiently ventilated to the outside air in such a manner that hot air from the stove shall not be drawn into any work room ; (d) no person shall enter a stove to remove the contents until a free current of air has been passed through it; (e) every vessel containing nitro or amino derivatives of phenol or of benzene or its homologues shall if steam is passed into or around it, or if the temperature of the contents be at or above the temperature of the boiling water, be covered in such a way that steam of vapour shall be discharged into the open air at a height of not less than 25 feet from the ground or the working platform, and at a point were it cannot be blown back again into the work-room. 4. Precautions during caustic grinding, etc.—(a) Every machine used for grinding or crushing caustic shall be enclosed; and (b) where any of the following processes are carried on— (i) grinding or crushing of caustic ; (ii) packing of ground caustic; (iii) grinding, sieving, evaporating or packing in a chrome process; (iv) crushing or mixing of material or cartridge filling in a nitro or amino process, an efficient exhaust draught shall be provided ; (v) Insecticides mentioned in sub-schedule "A" are manufactured, mixed, blended, or packed. 5. (a) Chlorate shall not be crystallised, ground or packed except in a room or place not used for any other purpose, the floor of which room or place shall be of cement or other smooth, impervious and incombustible material und shall be thoroughly cleaned daily. (b) Wooden vessels shall not be used for the crystallisation of chlorate, or to contain crystallised or ground chlorate: provided that this regulation shall not prohibit the packing of chlorate for sale into wooden casks or other wooden vessels. 6. Restrictions on the employment of young persons16 (a) No person under 18 years of age shall neither be employed in any process in which hydrochloric acid fumes or ammonical vapours are given off from the following operations- (i) evaporation of brine in open pans; (ii) stoving of salt; (iii) work at a furnace where the treatment of zinc is carried on; and (iv) the cleaning of work rooms where the process mentioned in (ii) is carried on: Provided that woman workers may be employed with their consent to work subjected to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernisc the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding woman shall not be employed or permitted to work at a bath. (b) No person under 18 years of age shall be employed in a chrome process or in nitro or amino process or in a process in which the following materials are used or where the vapour of such material is given off: 16 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 Carbon bisulphide, chlorides of sulphur, benzene, carbon tetrachloride trichlorathlene, any carbon chloride compound, or any mixture containing any of each materials 7. Every person employed— (a) in a process to which Paragraph 33 of this Schedule applies shall where the protective clothing, footwear, respirators, goggles or gloves, provided under Paragraph 33 and shall deposit overall or suit, or working clothing so provided as well as clothing put off during working hours, in the places provided under Paragraph 34; (b) in processes to which Paragraph 35 applies shall carefully wash the hands and face before partaking of any food or leaving the premises; (c) in any process to which Part II of this Schedule applies shall use the protective appliances supplied in respect of any process in which he is engaged. [SCHEDUFLE XIII] MANUFACTURE OR MANIPULATION OF CARCINOGENIC DYE INTERMEDIATES APPLICATION 1. Application.—The schedule shall apply in respect of all factories or any part thereof where processes in which the substances mentioned in paragraphs 3 and 4 are formed, manufactured, handled, or used and the processes incidental thereto in the course of which these substances are formed, are carried on. The processes indicated in this paragraph shall be referred to hereinafter as "the said processes" and such a reference shall mean any or all of the processes described in this paragraph. 2. Definitions.—For the purpose of this schedule the following definitions shall apply, unless the context otherwise requires :— (a) "Controlled Substances'' means chemical substances mentioned in paragraph 4 of this schedule. (b) "Efficient Exhaust Draught" means localised ventilation effected by mechanical means for the removal of gas, vapour, dust or fumes so as to prevent them from escaping into the air of any place in which work is carried on. No drought shall be deemed to be efficient which fails to remove smoke generated at the point where such gas, vapour, fume or dust originated. (c) "First Employment" means first employment in the said processes and also re-employment in such processes following any cessation of employment for a continuous period exceeding three calendar months, and (d) "Prohibited Substances" means chemical substances mentioned in paragraph 3 of this schedule. 3. Prohibited Substances.—For the purpose of this schedule, the following chemical substances shall be classified as "prohibited substances'' except when these substances are present or are formed as a bye-product of a chemical reaction in a total concentration not exceeding one per cent:— (a) Beta-naphthylamine and its salts ; (b) Benzidine and its salts ; (c) 4-amino diphenyl and its salts ; (d) 4-nitro diphenyl and its salts; and (e) any substance containing any of these compounds. 4. Controlled substances.—For the purpose of this schedule, the following chemical-substances shall be classified as "controlled substances" :— (a) Alpha-naphtylamine or alphanaphthylamine containing not more than one per cent of beta-naphthylamine either as a bye-product of chemical reaction or otherwise, and its salts, (b) Ortho-tolidine and its salts ; (c) Dianisidine and its salts ; (d) Dichlorobanzidine and its salts ; (e) Auramine, and (f) Magneta. 5. Prohibition of employment.—No person shall be employed in the said processes in any factory in which any prohibited substance is formed, manufactured, processed, handled, or used except as exempted by the Chief Inspector of Factories as stipulated in paragraph 23. 6. Requirements for processing or handling controlled substances.—(1) Where-ever any of the controlled substances referred to in paragraph 4 are formed, manufactured, processed, handled, or used, all practical steps shall be taken to prevent inhalation, ingestion or absorption of the said controlled substance by the workers while engaged in processing that substance, and its storage or transport while the plant, or in cleaning or maintenance of the concerned equipment, plant, machinery and storage areas. (2) As far as possible all operations shall be carried out in a totally enclosed system. Wherever such enclosure is not possible, efficient exhaust drought shall be applied at the point where the controlled substances. are likely to escape into the atmosphere during the process. (3) The controlled substances shall be received in the factory in tightly closed containers and shall be kept so except when these substances are in process or in use. The controlled substances shall leave the factory only in tightly closed containers of appropriate type. All the containers shall be' plainly labelled to indicate the contents. 7. Personal protective equipment.—(1) The following items of personal protective equipment shall be provided and issued to every workers employed in the said processes : (a) Long trousers and shirts or over alls with full sleeves and head coverings. The shirt or over alls shall cover the neck completely. (b) Rubber gum-boots. (2) The following items of personal protective equipment shall be provided in sufficient numbers for use by workers employed in the said processes when there is danger of injury during the performance of normal duties or in the event of emergency : (a) Rubber hand-gloves; (b) Rubber aprons; (c) Airline respirators or other suitable respiratory protective equipment. (3) It shall be the responsibility of the manager to maintain all items of personal protective equipments in a clean and hygienic condition and in good repair. 8. Prohibition relating to employment of young persons-No young person shall be employed or permitted to work in any room in which the said processes are carried on.17 8A-CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or permitted to work in any room in which the said processes are carried on with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed on permitted to work at a bath.9. Floors of work-room.—The floor of every work room in which the said processes are carried on shall be: (a) smooth and impervious to water provided that asphalt or tar shall no* be used in the composition of the floor; (b) maintained in a state of good repair; (c) with a suitable slope for easy draining and provided with gutters; and (d) thoroughly washed daily with the drain water being led into sewer through a closed channel. 10. Disposal of empty containers.—Empty container used for holding controlled substances shall be thoroughly cleaned of their contents and treated with an inactivating agent before being discarded. //. Manual handling.—Controlled substances shall not be allowed to be mixed, filled, emptied or handled except by means of a scoop with a handle. Such scoop shall be thoroughly cleaned daily. 12. Instructions regarding risk.—Every worker on his first employment in the said processes shall be fully instructed on the properties of the toxic 17 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 chemicals to which he is likely to be exposed to, of the danger involved and the precautions to be taken. Workers shall also be instructed on the measures to be taken to deal with an emergency. 13. Cautionary placards.—Cautionary placards in the form specified in Appendix attached to this Schedule and printed in the language of the majority of the workers employed in the said processes shall be affixed in prominent places frequented by them in the factory, where the placards can be easily and conveniently read. Arrangements shall be made by the manager to instruct periodically all such workers regarding the precautions contained in the cautionary placards. 14. Medical examination.—(1) Every worker employed in the said processes shall be examined by a Certifying Surgeon within 14 days of his first employment. Such examination shall include tests which the Certifying Surgeon may consider appropriate and shall include exfoliative cytology of the urine. No worker shall be allowed to work after 14 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once every six calendar months. Such examination shall include tests which the Certifying Surgeon may consider appropriate but shall include exfoliative cytology of the urine. (3) A person medically examined under sub-paragraph (1) shall be granted by a Certifying Surgeon a certificate of fitness in Form 26. Record of each re- examination carried out under sub-paragraph (2) shall be entered in the Certificate. The Certificate shall be kept in the custody of the manager of the factory. (4) The record of each examination carried out as referred to in subparagraphs (1) and (2) including the nature and the results of the tests shall be entered by the Certifying Surgeon in a health register in Form 27. (5) The certificates of fitness and the health register shall be kept readily available for inspection by any Inspector. (6) If at any time the Certifying Surgeon is of the opinion that a person is no longer fit for employment in the said processes or in any other work on the ground that continuance therein would involve damage to his health, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit for work in the said processes or in any work as the case may be. (7) No person who has been found unfit to work as said in subparagraph (6) shall be re-employed or permitted to work unless the Certifying Surgeon, after further examination, again certifies him to be fit for employment. 15. Medical facilities.—(1) The occupier of every factory in which the said processes are carried on shall engage a qualified medical practitioner for medical surveillance of the workers employed in such processes. His appointment shall be subject to approval of the Chief Inspector of Factories. (2) The occupier shall provide to him all the necessary facilities for the purpose referred to in sub-paragraph (1). (3) A record of medical examinations and appropriate tests carried out by the qualified medical practitioner shall be maintained in a form approved by the Chief Inspector. 16. Obligations of the workers.—It shall be the duty of the persons employed in the said processes to submit themselves for the medical examination including exfoliative cytology of urine by the Certifying Surgeon or the qualified medical practitioner as provided for under these rules. 17. Washing and bathing facilities.—(1) The following washing and bathing facilities shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the said processes: (a) A wash place under cover having constant supply of water and provided with clean towels, soap and nail brushes and with at least one stand pipe for every five such workers. (b) 50 per cent of the stand pipes provided under clause (a) shall be located in bathrooms where both hot and cold water shall be made available during the working hours of the factory and for one hour thereafter. (c) The washing and bathing facilities shall be in close proximity of the area housing the said processes. (d) Clean towels shall be provided individually to such worker. (e) In addition to the taps mentioned under clause (a), one stand pipe in which warm water is made available shall be provided on each floor. (2) Arrangement shall be made to wash factory uniforms and other work clothes every day. 18. Food, drink etc. prohibited in work room.—No worker shall consume food, drink, pan supari or tobacco or shall smoke in any work room in which the said processes are carried on and no worker shall remain in any such room during intervals for meals or rest. 19. Cloak room.—There shall be provided and maintained in a clean state and in good repair for the use of the workers employed in the said processes: (a) a cloak room with lockers having two compartments—one for street clothes and the other for work clothes; and (b) a place separate from the locker room and the mess room for the storage of protective equipments provided under paragraph 7. The accommodation so provided shall be under the care of responsible person and shall be kept clean. 20. Mess room.—There shall be provided and maintained for the use of workers employed in the said processes who remain on the premises during the meal intervals, mess room which shall be furnished with tables and benches and provided with suitable means for warming food. 21. Time allowed for washing.—Before the end of each shift 30 minutes shall be allowed for bathing each worker who is employed in the said processes. Further at least 10 minutes shall be allowed for washing before each meal in addition to the regular time allowed for meals. 22. Restriction on age of persons employed.—No worker under the age of 40 years shall be engaged in the factory in the said processes for the first time after the date on which the Schedule comes into force. 23. Exceptions—Prohibited substances.—(1) The Chief Inspector of Factories may by a certificate in writing (which he may at his discretion revoke at any time), subject to such conditions if any, as may be specified therein, exempt any process in the course of which any of the prohibited substances is formed, processed; manufactured, handled, or used from the provisions of paragraph 5 if he is satisfied that the process is carried out in a totally enclosed and hermetically sealed system in such a manner that the prohibited substance is not removed from the system except in quantities not greater than that required for the purpose of control of the process or such purposes as is necessary to ensure that the product is free from any of the prohibited substances. (2) The Chief Inspector of Factories may allow the manufacture, handling or use of benezidine hydrochloride provided that all the processes in connection with it are carried out in a totally enclosed system in such a manner that no prohibited substance other than benezidine hydrocholoride is removed therefrom except in quantities not greater tnan that required for the purpose of control of processes or such purposes as is necessary to ensure that the product is free from prohibited substances and that adequate steps are taken to insure that benezidine hydrochloride is except while not in a totally enclosed system, kept wet with not less than one part of water to two parts of benezidine hydrochloride at all times. 24. Exception—General.—If in respect of any factory, the Chief Inspector of Factories is satisfied that owing to the exceptional circumstances of infrequency of the processes or for any other reason, all or any of the provisions of this Schedule is not necessary for the protection of the workers in the factory, the Chief Inspector of Factories may by a certificate in writing (which he may in his discretion revoke at any time exempt such factory from all or any of such provisions subject to such conditions, if any as he may specify therein). APPENDIX Cautionary Placard-Notice 1. Dye intermediates which are nitro or amino derivatives or aromatic hydrocarbons are toxic. You have to handle these chemicals frequently in this factory. 2. Use the various items of protective wear to safeguard your own health. 3. Maintain scrupulous cleanliness at all times thoroughly wash hands and feet before taking meals. It is essential to take a bath before leaving the factory. 4. Wash off any chemicals falling on your body with soap and water. If splashed with a solution of the chemical, remove the contaminated clothing immediately. These chemicals are known to produce cyanosis. Contact the medical officer or appointed doctor immediately and get his advice. 5. Handle the dye intermediates only with long handled scoops, never with bare hands. 6. Alcoholic drinks should be avoided as they enhance the risk of poisioning by the chemicals. 7. Keep your food and drinks away from work-place. Consuming food, drinks or tobacco in any form at the place of work is prohibited. 8. Serious effect from work with toxic chemicals may follow after many years. Great care must be taken to maintain absolute cleanliness of body, clothes, machinery and equipments. [SCHEDULE XIV] MANUFACTURE HANDLING AND USAGE OF BENZENE AND SUBSTANCES CONTAINING BENZENE 1. This Schedule is made to provide protection against hazards of poisoning from benzene and shall apply in respect of factories or parts thereof in which benzene or substances containing benzene are manufactured, handled or used. 2. Definitions.—For the purpose of this Schedule : (a) 'substances containing benzene' means substances wherein benzene content exceeds 1 per cent by volume ; (b) 'substitute" means a chemical which is harmless or less harmful than benzene and can be used in place of benzene; (c) 'enclosed system' means a system which will not allow escape of benzene vapours to the working atmosphere ; and {d) 'efficient exhaust draught' means localised ventilation effected by mechanical means for the removal of gases, vapours and dusts or fumes so as to prevent them from escaping into the air of any workroom. No draught shall be deemed to be efficient if it fails to remove smoke generated at the point where such gases, vapours, fumes or dusts originate. 3. Prohibition and substitution.—(1) Use of benzene and substances containing benzene is prohibited in the following processes— (a) manufacture of varnish, paints and thinners ; (b) cleaning and degreasing operations. (2) Benzene or substances containing benzene shall not be used as a solvent or diluent unless the processes in which it is used is carried or in an enclosed system or unless the processes is carried on in a manner which is considered equally safe as it were carried out in an enclosed system. (3) Where suitable substitutes are available, they shall be used instead of benzene or substances containing benzene. This provision, however, shall not apply to the following processes: (a) Production of benzene ; (b) Process where benzene is used for chemical synthesis ; and (c) Motor spirits (use and fuel). (4) The Chief Inspector may, subject to confirmation by the State Government, permit exemptions from the percentage laid down in Paragraph 2(a) and also from the provisions of sub-paragraph (2) of this paragraph temporarily under conditions and within limits of time to be determined after consultation with the employers and workers concerned. 4. Protection against inhalation.—(1) The process involving the use of benzene or substances containing benzene shall as far as practicable be carried out in an enclosed system. (2) Where, however, it is not practicable to carry out the process in an enclosed system, the workroom in which benzene or substances containing benzene are used shall be equipped with an efficient exhaust draught or other means for the removal of benzene vapours to prevent their escape into the air or the workroom so that the concentration of benzene in the air does not exceed 25 parts per million by volume or 80 milligrams per cublic metre. (3) Air analysis for the measurements of concentration of benzene vapours in air shall be carried out every 8 hours or at such intervals as may be directed by the Chief Inspector at places where process involving use of benzene is carried on and the results of such analysis shall be recorded in a register specially maintained for this purpose. If the concentration of benzene vapours in air as measured by air analysis, exceed 25 parts per million by volume or 80 milligrams per cubic metre, the Manager shall forthwith report the concentration of the Chief Inspector stating reasons for such increase. (4) Workers who for special reasons are likely to be exposed to concentration of benzene in the air or the workroom exceeding the maximum referred in sub- paragraph (2) shall be provided with suitable respirators face masks. The duration of such exposure shall be limited as far as possible. 5. Measures against skin contact.—(1) Workers who are likely to come in contact with liquid benzene or liquid substance containing benzene shall be provided with suitable gloves, aprons, boots and where necessary vapour tight chemical goggles, made of material not affected by benzene or its vapours. (2) The protective wear referred to in sub-paragraph (i) shall be maintained in good condition and inspected regularly. 6. Prohibition relating to employment of women and young persons.—No woman or young person shall be employed or permitted to work in any workroom involving exposure to benzene or substances containing benzene. 7. Labelling.—Every container holding benzene or substances containing benzene shall have the word "Benzene" and approved danger symbols clearly visible on it and shall also display information on benzene content warning about toxicity and warning about inflammability of the chemical. 8. Improper use of benzene.—(1) The use of benzene or substances containing benzene by workers for cleaning their hands or their work clothing shall be prohibited. (2) Workers shall be instructed on the possible dangers arising from such misuse. 9. Prohibition of consuming food, etc., in workroom.—No worker shall be allowed to store or consume food or drink in the workroom in which benzene or substances containing benzene are manufactured, handled or used. Smoking and chewing tobacco or pan shall be prohibited into such workrooms. 10. Instruction as regards risks.—Every worker on his first employment shall be fully instructed on the properties of benzene or substances containing benzene which he has to handle and of the dangers involved. Workers shall also be instructed on the measure to be taken to deal with an emergency. 11. Cautionary notices.—Cautionary notices in the form specified in Appendix 'A' and presented in the language easily read and understood by the majority of the workers shall be displayed in prominent places in the workrooms where benzene or substances containing benzene are manufactured, handled or used. 12. Washing facilities cloak room and messrom.—In factories in which benzene or substances containing benzene are manufactured, handled or used the occupier shall provide and maintain in clean state and in good repair : (1) Washing facilities under cover of the standard of at least one tap for every 10 persons having constant supply of water with soap and a clean towel provided individually to each worker if so ordered by the Inspector ; (2) A cloak room with lockers for each workers, having two compartments one for street clothing and one for work-clothing ; and (3) A messroom furnished with tables and benches with means for warming food, provided that where a canteen or other proper arrangements exist for the workers to take their meals, the requirements of messroom shall be dispensed with. 13. Medical Examination.—(1) Every worker who is to be employed in processes involving use of benzene or substances containing benzene, shall undergo— (a) a thorough pre-employment medical examination including a blood test for fitness for employment by a certifying surgeon; and (b) periocical medical examination including blood test and other biological tests at intervals of every 6 months by the factory medical officer with the assistance of a laboratory. (2) Certificates of pre-employment medical examination and periodical medical examination including tests, shall be entered in a health register in Form No. 17, which shall be produced on demand by an Inspector. (3) If the factory medical officer on examination at any time is of the opinion that any worker has developed signs or symptoms of benzene exposure, he shall make a record of his findings in the said register and inform the manager in writing and on receipt of the information from the factory medical officer, the manager of the factory shall send the worker so found exposed, to the certifying surgeon who shall, after satisfying himself with the finding of the factory medical officer and conducting necessary examination, issue orders of temporary shifting of the worker or suspension of the worker in the process. (4) The medical examination shall be arranged by the occupier or manager of the factory and the worker so examined shall not bear any expenses for it. [SCHEDULE XV] MANUFACTURE OF POTTERY 1. Savings.—These provisions shall not apply to a factory in which any of the following articles, but no other pottery, are made— (a) unglazed or salt glazed bricks and tiles; and (b) architectural terracotta made from plastic clay and either unglazed or glazed with a leadless glaze only. 2. Definitions.—For the purposes of this Schedule— (a) "Efficient exhaust draught" means localized ventilation effected by mechanical or other means for removal of dust or fume so as to prevent it from escaping into air of any place in which work is carried on. No draught shall be deemed efficient which fails to remove effectively dust or fume generated at the point where dust or fume originates; (b) "fettling" includes scalloping, towing, sand peppering, sand sticking, brushing or any other process of cleaning of potteryware in which dust is given off; (c) "first employment" shall mean first employment in any process mentioned under Paragraph 3 and shall also include re-employment in the said process following any cessation of employment for a continuous period exceeding three calendar months; (d) "ground or powdered flint or quartz" does not include natural sands; (e) "leadless glaze" means a glaze which does not contain more than one per cent of its dry weight of a lead compound calculated as lead monoxide; (f) "low solubility glaze" means a glaze which does not yield to dilute hydrochloric acid more than five per cent of its dry weight, of a soluble lead compound calculated as lead monoxide when determined in the manner described below— A weighed quantity of the material which has been dried at 100 degrees centigrade and thoroughly mixed shall be continuously shaken for one hour at the common temperature with 1000 times its weight of an aqueous solution of hydrochloric acid containing 0.25 per cent by weight of hydrogen chloride. This solution shall thereafter be allowed to stand for one hour and then filtered. The lead salt contained in the clear filtrate shall then be precipitated as lead sulphide and weighed as lead sulphate; (g) "potter's shop" includes all places where pottery is formed by pressing or by any other process and all places whereby pressing or by any other process and all places where shaping, fettling or other treatment of pottery article prior to placing for the biscuit fire is carried on; and (h) "Pottery" includes earthenware, stoneware, porcelain, chinatiles, and any other articles made from such clay or from a mixture containing clay and other materials such as quartz, flint, felpspar, and gypsum. 3. Efficient exhaust draughts.—The following processes shall not be carried on without the use of an efficient exhaust draught: (a) all processes involving the manipulation or use of a dry and unfritted lead compound; (b) fettling operations of any kind, whether on greenware or biscuit, provided that this shall not apply to the wet fettling, and to the occasional finishing of pottery articles without the aid of mechanical power; (c) sifting of clay dust or any other material for making tiles or other articles by pressure, except where— (i) this is done in machine so enclosed as to effectually prevent the escape of dust; or (ii) the material to be shifted is so damp that no dust can be given off; (d) pressing of tiles from clay dust, an exhaust opening being connected with each press, and pressing from clay dust of articles other than tiles, unless the material is so damp that no dust is given off; (e) fettling of tiles made from clay dust by pressure, except where the fettling is done wholly on or with, damp material, and fettling of other articles made from clay dust, unless the material is so damp that no dust is given off; (f) process of loading and unloading of saggers where handling and manipulation of ground and powdered flint, quartz, aluminia or other materials are involved; (g) brushing of earthenware biscuit, unless the process is carried on in a room provided with efficient general mechanical ventilation or other ventilation which is certified by the Inspector as adequate having regard to all the circumstances of the case; (h) fettling of biscuitware which has been fired in powdered flint or quartz except where this is done in machine so enclosed as to effectually prevent the escape of dust; (i) ware cleaning after the application of glaze by dipping or other process; (j) crushing and dry grinding of materials for pottery bodies and saggars, unless carried on in machines so enclosed as to effectively prevent the escape of dust or is so damp that no dust can be given off; (k) sieving or manipulation of powdered flint, quartz, clay grog or mixture of these materials unless it is so damp that no dust can be given off; (l) grinding of tiles on a power driven wheel unless an efficient water spray is used on the wheel; (m) lifting and conveying of materials by elevators and conveyers unless they are effectively enclosed and so arranged as to prevent escape of dust into the air in or near to any place in which persons are employed; (n) preparation or weighing out of flow material, lawning of dry colours, colour dusting and colour blowing; (o) mould making unless the bins or similar receptacles used for holding plaster of paris are provided with suitable covers; and (p) manipulation of calcined material unless the material has been made and remains so wet that no dust is given off. 4. Separation of process.—Each of the following processes shall be carried on in such a manner and under such conditions as to secure effectual separation from one another and from other wet processes— (a) crushing and dry grinding or sieving of materials, fettling, pressing of tiles, drying of clay and greenware, loading and unloading of saggars, and the use of a dry lead compound, (b) all processes involving the use of a dry lead compound. 5. Prohibition on use of glaze.—No glaze which is not a leadless glaze or a low solubility glaze shall be used in a factory in which pottery is manufactured. 6. Prohibition relating to young persons-No young person shall be employed or permitted to work in any of the operations specified in Paragraph 4, or at any place where such operations are carried on.18 18 Provisions of clause (3) of Article 348 of the Constitution, the Governor is pleased to order the publication of the following English translation of Notification no. 09/2024/2411/XXXVI-03-2024-1792147, dated December 23, 2024: 7. Provisions of screen to potter's wheel.—The potter's wheel (jolly and jigger) shall be provided with screens or so constructed as to prevent clay scrapings being thrown off beyond the wheel. 8. Control of dust during cleaning.—(1) All practical measures shall be taken by dampening or otherwise to prevent dust arising during cleaning of floors. (2) Damp sawdust or other suitable material shall be used to render the moist method effective in preventing dust rising into the air during the cleaning process which shall be carried out after work has ceased. 9. Floor of certain workrooms.—The floors of potter's shops, slip houses, dipping houses and ware cleaning rooms shall be hard, smooth and impervious and shall be thoroughly cleaned daily by an adult male using a moist method. 10. Protective equipment.—(1) The occupier shall provide and maintain suitable overalls and head coverings for all persons employed in process included under Paragraph 3. (2) The occupier shall provide and maintain suitable aprons of a waterproof or similar material which can be sponged daily, for the use of the dippers, dippers' assistants, throwers, jolly workers, casters, mould makers and filterpress and pug mill workers. (3) Aprons provided in pursuance of sub-paragraph (2) shall be thoroughly cleaned daily by the wearers by sponging or otheV wet processes. All overalls and head coverings shall be washed, cleaned arid mended at least once a week, and this washing, cleaning or mending shall be provided for by the occupier. (4) No person shall be allowed to work in emptying sacks of dusty materials, weighing out and mixing of dusty materials, and charging of ballmills and plungers without wearing a suitable and efficient dust respirator. 11. Washing facilities.—(1) The occupier shall provide and maintain, in a clean state and in good repair for the use of all persons employed in any of the processes specified in Paragraph 8— (a) a wash place under cover with either— (i) a trough with smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimetres for every five such persons employed at any one time, and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 centimetres; or (ii) at least one tap or standpipe for every five such persons employed at any one time, and having a constant supply of clean water, the tap or standpipe being spaced not less than 120 centimetres apart; and (b) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. 12. Tune allowed for washing.—Before each meal and before the end of the day's work, at least ten minutes, in addition to the regular meal times, shall be allowed for washing to each person employed in any of the processes mentioned in Paragraph 3. 13. Mess-room.—(1) There shall be provided and maintained for use of all persons remaining within the premises during the rest intervals, a suitable mess- room providing accommodation of 0.93 square metre per head and furnished with— (a) a sufficient number of tables and chairs or benches with back rest; (b) arrangements for washing utensils; (c) adequate means for warming food; and (d) adequate quantity of drinking water. (2) The room shall be adequately ventilated by the circulation of fresh air and placed under the charge of a responsible person and shall be kept clean. 14. Food, drinks, etc. prohibited in workrooms.—No food, drink, pan, supari and tobacco shall be brought into or consumed by any worker in any workroom in which any of the processes mentioned in Paragraph 3 are carried on and no person shall remain in any such room during interval for meals or rest. 15. Cloak-room, etc.—There shall be provided and maintained for the use of all persons employed in any of the processes mentioned in Paragraph 3,— (a) a cloak-room for clothing put off during working hours and such accommodation shall be separate from any mess-room; and (b) separate and suitable arrangements for the storage of protective equipment provided under Paragraph 10. 16. Medical facilities and records of examinations and tests.—(1) The occupier of every factory in which manufacturing of pottery is carried on, shall— (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examination and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 17. Medical examination by Certifying Surgeon.—(1) Every worker employed in any process mentioned under Paragraph 3, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for lead in urine and blood, ALA in urine, haemoglobin content, stippling of cells and pulmonary function tests and chest X-ray for workers engaged in processes mentioned in clauses (a) and (n) of Paragraph 3 and pulmonary function test and chest X-rays for the others. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) All persons employed in any of the processes mentioned in clauses (a) and (n) of Paragraph 3 shall be examined by a Certifying Surgeon once in every 3 calendar months. Those employed in any other processes mentioned in the remaining clauses of Paragraph 3 shall be examined by a Certifying Surgeon once in every twelve calendar months. Such examinations in respect of all the workers shall include all the tests as specified in sub-paragraph (1) except chest X-ray which will be once in 3 years. (3) The Certifying Surgeon after examining a worker, shall issue Certificate of Fitness in Form 26. The record of examination and re-examination carried out shall be entered in the certificate and the certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to health of the worker, he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit for work in the said processes. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination again certifies him fit for employment in those processes. 18. Exemption.—If in respect of any factory the Chief Inspector is satisfied that all or any of the provisions of this Schedule are not necessary for the protection of the persons employed in such factory, he may by a certificate in writing exempt such factory from all or any of such provisions subject to such conditions as he may specify therein. Such certificate may at any time be revoked by the Chief Inspector without assigning any reasons. SCHEDULE XVI MANIPULATION OF STONE OR ANY OTHER MATERIAL CONTAINING FREE SILICA 1. Application.—This Schedule shall apply to all factories or parts of factories in which manipulation of stone or any other material containing free silica is carried on. 2. Definitions.—For the purpose of this Schedule— (a) "First employment" shall mean first employment in the processes specified in Paragraph 1 and shall also include re-employment in the said processes following any cessation of employment for a continuous period exceeding three calendar months; (b) "manipulation" means crushing, breaking, chipping, dressing, grinding, sieving, mixing, grading or handling of stone or any other material or any other operation involving such stone or material; and (c) "stone or any other material containing free silica" means a stone or any other solid material containing not less than 5 per cent by weight of free silica. 3. Precautions in manipulation.—No manipulation shall be carried out in a factory or part of a factory unless one or more of the following measures, namely— (a) dampening the stone or other material being processed; (b) providing water spray; (c) enclosing the processes; (d) isolating the process; and (e) providing localized exhaust ventilation: are adopted so as to effectively control the dust in any place in the factory where any person is employed, at a level equal to or below the maximum permissible level for silica dust as laid down in the second Schedule appended to Section 41- F of the Act: Provided that such measures as abovesaid are not necessary if the process of operation itself is such that the level of dust created and prevailing does not exceed the permissible level referred to. 4. Maintenance of floors.—(1) All floors or places where fine dust is likely to settle on and wherein any person has to work or pass shall be of impervious material and maintained in such condition that they can be thoroughly cleaned by a moist method or any other method which would prevent dust being airborne in the process of cleaning. (2) The surface of every floor of every workroom or place where any work is carried on or where any person has to pass during the course of his work, shall be cleaned of dust once at least during each shift after being sprayed with water or by any other suitable method so as to prevent dust being airborne in the process of cleaning. 5. Prohibition relating to young persons.—No young person shall be employed or permitted to work in any of the operations involving manipulation or at any place where such operations are carried on. 6. Medical facilities and records of examinations and tests.—(1) The occupier of every factory to which the Schedule applies, shall— (a) employ a qualified medical officer for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories, and (b) provide to the said medical officer all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examination and appropriate tests carried out by the said medical officer shall be maintained in separate register approved by the Chief Inspector of Factories which shall be kept readily available for inspection by the Inspector. 7. Medical examination by Certifying Surgeon.—(1) Every worker employed in the processes specified in Paragraph 1, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such medical examination shall include pulmonary function tests and chest X-ray. No worker shall be allowed to work after 15 days of his first employment unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every twelve months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub-paragraph (1) except chest X-ray which will be once in every 3 years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of re-examination carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the Factory. The record of each examination carried out under sub-paragraphs (1) and (2) including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in those documents also include the period for which he considers that the said person is unfit for work in the said processes. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the said process unless the Certifying Surgeon after further examination, again certifies him fit for employment in those processes. 8. Exemption.—If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this Schedule are not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. SCHEDULE XVII HANDLING AND PROCESSING OF ASBESTOS, MANUFACTURE OF ANY ARTICLE OF ASBESTOS AND ANY OTHER PROCESS OF MANUFACTURE OR OTHERWISE IN WHICH ASBESTOS IS USED IN ANY FORM 1. Application.—This Schedule shall apply to all factories or part of factories in which any of the following processes are carried on— (a) breaking, crushing, disintegrating, opening, grinding, mixing or sieving of asbestos and any other processes involving handling and manipulation of asbestos incidental thereto; (b) all processes in the manufacture of asbestos textiles including preparatory and finishing processes; (c) making of insulation slabs or sections, composed wholly or partly ofmasbestos and processes incidental thereto; (d) making or repairing of insulating mattresses composed wholly or partly of asbestos, and processes incidental thereto; (e) manufacture of asbestos cardboard and paper; (f) manufacture of asbestos or cement goods; (g) application of asbestos by spray method; (h) sewing, grinding, turning, abrading and polishing in the dry state of articles composed wholly or partly of asbestos; (i) cleaning of any room, vessel, chambers, fixture or appliance for the collection of asbestos dust; and (j) any other processes in which asbestos dust is given off into the work environment. 2. Definition.—For the purpose of this Schedule— (a) "approved" means approved for the time being in writing by the Chief Inspector; (b) "asbestos" means any fibrous silicate mineral and any admixture containing actionlite, amosite, anthophylite, chrysolite, corcidelite, tremolite or any mixture thereof, whether crude, crushed or opened; (c) "asbestos textiles" means yarn or cloth composed of asbestos mixed with any other material; (d) "breathing apparatus" means a helmet or face piece with necessary connection by means of which a person using it breathes air free from dust, or any other approved apparatus; (e) "efficient exhaust draught" means localized ventilation by mechanical means for the removal of dust so as to prevent dust from escaping into air of any place in which work is carried on. No draught shall be deemed to be efficient which fails to control dust produced at the point where such dust originates; (f) "first employment" shall mean first employment in the processes, specified in Paragraph 1 and shall also include re-employment in the said processes following any cessation of employment for a continuous period exceeding three calendar months; (g) "preparing" means crushing, disintegrating, and any other processes in or incidental to the opening of asbestos; and (h) "protective clothing" means overall and head covering, which (in either case) will when worn exclude asbestos dust. 3. Tools and equipment.—Any tools or equipment used in processes to which this Schedule applies shall be such that they do not create asbestos dust above the permissible limit or are equipped with efficient exhaust draught. 4. Exhaust draught.—(1) An efficient exhaust draught shall be provided and maintained to control dust from the following processes and machines— (a) manufacture and conveying machinery, namely— (i) preparing, grinding or dry mixing machines; (ii) carding, card waste and ring spinning machines, and looms; (iii) machines or other plant fed with asbestos; and (iv) machines used for the sewing, grinding, turning, drilling, abrading or polishing, in the dry state, of articles composed wholly or partly of asbestos. (b) cleaning and grinding of the cylinders or other parts of a carding machine; (c) chambers, hoppers or other structures into which loose asbestos is delivered or passes; (d) workbenches for asbestos waste sorting or for other manipulation of asbestos by hand; (e) workplaces at which the filling or emptying of sacks, skips or other portable containers, weighing or other process incidental thereto which is effected by hand, is carried on; (f) sack cleaning machines; (g) mixing and blending of asbestos by hand; and (h) any other process in which dust is given off into the work environment. (2) Exhaust ventilation equipment provided in accordance with sub-paragraph (1) shall, while any work of maintenance or repair to the machinery, apparatus or other plant or equipment in connection with which it is provided is being carried on, be kept in use so as to produce an exhaust draught which prevents the entry of asbestos dust into the air of any workplace. (3) Arrangements shall be made to prevent asbestos dust discharged from exhaust apparatus being drawn into the air of any workroom. (4) The asbestos bearing dust removed from any workroom by the exhaust system shall be collected in suitable receptacles or filter bags which shall be isolated from all work areas. 5. Testing and examination of ventilating systems.—(1) All ventilating systems used for the purpose of extracting or suppressing dust as required by this Schedule shall be examined and inspected once every week by a responsible person. It shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examinations or test shall be rectified forthwith. (2) A register containing particulars of such examination and tests and the state of the plant and repairs or alterations (if any) found to be necessary shall be kept and shall be available for inspection by an Inspector. 6. Segregation in case of certain process.—Mixing or blending by hand of asbestos, or making or repairing of insulating mattresses composed wholly or partly of asbestos shall not be carried on in any room in which any other work is done. 7. Storage and distribution of loose asbestos.—All loose asbestos shall while not in use, be kept in suitable closed receptacles which prevent the escape of asbestos dust therefrom and such asbestos shall not be distributed within a factory except in such receptacles or in a totally enclosed system of conveyance. 8. Asbestos sacks.—(1) All sacks used as receptacles for the purpose of transport of asbestos within the factory shall be constructed of impermeable material and shall be kept in good repair. (2) A sack which has contained asbestos shall not be cleaned by hand beating but by a machine, complying with Paragraph 3. 9. Maintenance of floors and workplaces—(1) In every room in which any of the requirements of this Schedule apply— (a) the floors, workbenches, machinery and plant shall be kept in a clean state and free from asbestos debris and suitable arrangements shall be made for the storage of asbestos not immediately required for use; and (b) the floors shall be kept free from any materials, plant or other articles not immediately required for the work carried on in the room and which would obstruct the proper cleaning of the floor. (2) The cleaning as mentioned in sub-paragraph (1) shall, so far as is practicable, be carried out by means of vacuum cleaning equipment as designed and constructed and so used that asbestos dust neither escapes nor is discharged into the air of any workplace. (3) When the cleaning is done by any method other than that mentioned in sub- paragraph (2), the persons doing cleaning work and any other person employed in that room shall be provided with respiratory protective equipment and protective clothing. (4) The vacuum cleaning equipment used in accordance with provisions of sub- paragraph (2), shall be properly maintained and after each cleaning operation, its surface shall be kept in a clean state and free from asbestos waste and dust. (5) Asbestos waste shall not be permitted to remain on the floors or other surfaces at the workplace at the end of the working shift and shall be transferred without delay to suitable receptacles. Any spillage of asbestos waste occurring during the course of the work at any time shall be removed and transferred to the receptacles maintained for the purpose without delay. 10. Breathing apparatus and protective clothing.—(1) An approved breathing apparatus and protective clothing shall be provided and maintained in good condition for use of every person employed— (a) in chambers containing loose asbestos; {b) in cleaning, dust settling, or filtering chambers, or apparatus; (c) in cleaning the cylinders, including the doffers cylinders, or other parts of a carding machine by means of hand-strickles; (d) in filling, beating, or levelling in the manufacture or repair of insulating mattresses; and (e) in any other operation or circumstance in which it is impracticable to adopt technical means to control asbestos dust in the work environment within the permissible limit. (2) Suitable accommodation in conveniently accessible position shall be provided for the use of persons when putting on or taking off breathing apparatus and protective clothing provided in accordance with this Schedule and for the storage of such apparatus and clothing when not in use. (3) All breathing apparatus and protective clothing when not in use shall be stored in the accommodation provided in accordance with sub-paragraph (2). (4) All protective clothing in use shall be re-dusted under an efficient exhaust draught or by vacuum cleaning and shall be washed at suitable intervals. The cleaning Schedule and procedure should be such as to ensure the efficiency of the said clothing in protecting the wearer. (5) All breathing apparatus shall be cleaned and disinfected at suitable intervals and thoroughly inspected once every month by a responsible person. (6) Records of the cleaning and maintenance and of the condition of the breathing apparatus shall be maintained in a register provided for that purpose which shall be readily available for inspection by an Inspector. (7) No person shall be employed to perform any work specified in sub- paragraph (1) for which breathing apparatus is necessary to be provided under that sub-paragraph unless he has been fully instructed in the proper use of that equipment. (8) No breathing apparatus provided in pursuance of sub-paragraph (1) which has been worn by a person, shall be worn by another person unless it has been thoroughly cleaned and disinfected since last being worn and the person has been fully instructed in the proper use of that equipment. 11. Separate accommodation for personal clothing.—A separate accommodation shall be provided in a conveniently accessible position for all persons employed in operations to which this Schedule applies for storing of personal clothing. This should be separated from the accommodation provided under sub-paragraph (2) of Paragraph 10 to prevent contamination of personal clothing. 12. Washing and bathing facilities.—(1) There shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the processes covered by the Schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 15 persons employed. (2) The washing places shall have standpipes placed at intervals of not less than one metre. (3) Not less than one-half of the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable materials shall be provided: Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 13. Mess-room.—(1) There shall be provided and maintained for the use of all workers employed in the factory covered by this Schedule, remaining on the premises during the rest intervals, a suitable mess-room which shall be furnished with— (a) sufficient tables and benches with back-rest, and (b) adequate means for warning food. (2) The mess-room shall be placed under the charge of a responsible person and shall be kept clean. 14. Prohibition of employment of young persons.—No young person shall be employed in any of the processes covered by this Schedule. 15. Prohibition relating to smoking.—No person shall smoke in any area where processes covered by this Schedule are carried on. A notice in the language understood by majority of the workers shall be posted in the plant prohibiting smoking at such areas. 16. Cautionary Notices.—(1) Cautionary notices shall be displayed at the approaches and along the perimeter of every asbestos processing area to warn all persons regarding: (a) hazards to health from asbestos dust; (b) need to use appropriate protective equipment; and (c) prohibition of entry to unauthorised persons or authorised persons but without protective equipment. (2) Such notices shall be in the languages understood by the majority of the workers. 17. Air Monitoring.—To ensure the effectiveness of the central measures, monitoring of asbestos in air shall be carried out once at least in every shift and the record of the results so obtained shall be entered in a register specially maintained for the purpose. 18. Medical facilities and records of medical examinations and tests.—(1) The occupier of every factory or part of the factory to which the Schedule applies, shall— (a) employ a qualified medical practitioner for medical surveillance of the workers covered by this Schedule whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 19. Medical examination by Certifying Surgeon.—(1) Every worker employed in the processes specified in Paragraph 1 shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests, tests for detecting asbestos fibers in sputum and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the process referred to in sub-paragraph (1) shall be re-examined by a Certifying Surgeon at least once in every twelve calendar months. Such examinations shall, wherever the Certifying Surgeon considers appropriate include all the tests specified in sub-paragraph (1) except chest X-ray which will be carried out once in 3 years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of examination and re-examinations carried out shall be entered in the certificate and the certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the test, shall also be entered, by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit to work in the said processes. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 20. Exemption.—If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or infrequency of the processes for any other reason, all or any of the provisions of this Schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such condition, if any, as he may specify therein. SCHEDULE XVIII HANDLING OR MANIPULATION OF CORROSIVE SUBSTANCES 1. Definition.—For the purposes of this Schedule— (a) "corrosive operation" means an operation of manufacturing, storing, handling, processing, packing or using any corrosive substance in a factory; and (b) "corrosive substance" includes Sulphuric acid, Nitric acid, Hydrochloric acid, Hydrofluoric acid, Carbolic acid, Phosphoric acid. Liquid chlorine, Liquid bromine, Ammonia, Sodium hydroxide and Potassium hydroxide and a mixture thereof, and any other substance which the State Government by notification in the Official Gazette specify to be a corrosive substance. 2. Flooring.—The floor of every workroom of a factory in which corrosive operation is carried on shall be made of impervious, corrosion and fire resistant material and shall be so constructed as to prevent collection of any corrosive substance. The surface of such flooring shall be smooth and cleaned as often as necessary and maintained in a sound condition. 3. Protective equipment.—(1) The occupier shall provide for the use of all persons employed in any corrosive operation suitable protective wear for hands and feet, suitable aprons, face shields, chemical safety goggles and respirators. The equipments shall be maintained in good order and shall be kept in a clean and hygienic condition by suitably treating to get rid of the ill effects of any absorbed chemicals and by disinfecting. The occupier shall also provided suitable protective creams and other preparations wherever necessary. (2) The protective equipment and preparations provided shall be used by the persons employed in any corrosive operation. 4. Water facilities.—Where any corrosive operation is carried on, there shall be provided as close to the place of such operation as possible a source of clean water at a height of 210 centimetres from a pipe of 1.25 centimetres diameter and fitted with a quick acting valve so that in case of injury to the worker by any corrosive substance, the injured part can be thoroughly flooded with water. Whenever necessary, in order to ensure continuous water supply, a storage tank having a minimum length, breadth and height of 210 centimeters, 120 centimeters and 60 centimeters respectively or such dimensions as are approved by the Chief Inspector shall be provided as the source of clean water. 5. Cautionary notice.—A cautionary notice in the following form and printed in the language which majority of the workers employed understand, shall be displayed prominently close to the place where a corrosive operation is carried out and where it can be easily and conveniently read by the workers. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so displayed. CAUTIONARY NOTICE DANGER Corrosive substances cause severe burns and vapours thereof may be extremely hazardous. In case of contact, immediately flood the part effected with plenty of water for at least 15 minutes 6. Transport.—(1) Corrosive substances shall not be filled, moved or carried except in containers or through pipes and when they are to be transported in containers they shall be placed in crates of sound construction and of sufficient strength. (2) A container with a capacity of 11.5 litres or more of a corrosive substance shall be placed in a receptacle or crate and then carried by more than one person at a height below the waist line unless a suitable rubber wheeled truck is used for the purpose. (3) Containers for corrosive substances shall be plainly labelled. 7. Devices for handling corrosives.—(1) Tilting, lifting or pumping arrangements shall be used for emptying jars, carboys and other containers of corrosives. (2) Corrosive substance shall not be handled by bare hands but by means of a suitable scoop or device. 8. Openings of valves.—Valves fitted to containers holding a corrosive substance shall be opened with great care. If they do not work freely, they shall not be forced open. They shall be opened by a worker suitably trained for the purpose. 9. Cleaning tanks, sills etc.—(1) In cleaning out or removing residues from sills or other large chambers used for holding any corrosive substance, suitable implements made of wood or other material shall be used to prevent production of arseniuretted hydrogen (arsine). (2) Whenever it is necessary for the purpose of cleaning or other maintenance work for any worker to enter chamber, tank, vat, pit or other confined space where a corrosive substance had been stored, all possible precautions required under Section 36 of the Act shall be taken to ensure the worker's safety. (3) Wherever possible, before repairs are undertaken to any part of equipment in which a corrosive substance was handled, such equipment or part thereof shall be freed of any adhering corrosive substance by adopting suitable method. 10. Storage.—(1) Corrosive substances shall not be stored in the same room with other chemical materials such as turpentine, carbides, metallic powders and combustible materials, to accidental mixing with, which may cause a reaction which is either violent or gives rise to toxic fumes and gases. (2) Pumping or filling overhead tanks, receptacles vats or other container for storing corrosive substances shall be so arranged that there is no possibility of any corrosive substance overflowing and causing injury to any person. (3) Every container having a capacity of twenty litres or more and every pipeline, valve, and fitting used for storing or carrying corrosive substance shall be thoroughly examined every year for finding out any defects, and defects so found out shall be removed forthwith. A register shall be maintained of every such examination made and shall be produced before the Inspector whenever required. 11. Fire extinguishers and fire-fighting equipment.—An adequate number of suitable type of fire extinguishers or other fire-fighting equipment, depending on the nature of chemicals stored, shall be provided. Such extinguishers or other equipment shall be regularly tested and refilled. Clear instructions as to how the extinguishers or other equipment should be used, printed in the language which majority of the workers employed understand, shall be affixed near each extinguisher or other equipment. 12. Exemption.—If in respect of any factory on an application made by the Manager, the Chief Inspector is satisfied that owing to the exceptional circumstances, or the infrequency of the process or for any other reason to be recorded by him in writing, all or any of the provisions of this Schedule are not necessary for the protection of the persons employed therein, he may by a certificate in writing which he may at any time revoke, exempt the factory from such of the provisions and subject to such conditions as he may specify therein. SCHEDULE XIX COMPRESSION OF OXYGEN AND HYDROGEN PRODUCED BY ELECTROLYSIS OF WATER 1. Location of electrolyser plant.—The room in which electrolyser plant is installed shall be separate from the plant for storing and compressing the oxygen and hydrogen and also the electric generator room. 2. Testing of purity.—(1) The purity of oxygen and hydrogen shall be tested by competent person at least once in every shift at the following posts— (a) in the electrolysis room; (b) at the gas-holder inlet; and (c) at the suction and of the compressor. (2) The purity figures shall be entered in a register and signed by the persons carrying out such tests: Provided that if the electrolyser plant is fitted with automatic recorder of purity of oxygen and hydrogen with alarm lights, it shall be sufficient to the purity of gases is tested at the suction and of the compressor only. 3. Restrictions as to the compression.—The oxygen and hydrogen gases shall not be compressed if their purity as determined under Paragraph 2 above falls below 98 per cent at any time. 4. Limit switch for gasholder.—The bell of any gasholder shall not be permitted to go within the 30 centimeters of its lowest position when empty and a limit switch shall be fitted in the gasholder in such a manner as to switch off the compressor motor when the limit is reached. 5. Provision of negative pressure switch.—In addition to the limit switch in the gasholder, a sensitive negative pressure switch shall be provided in or adjacent to the suction main for hydrogen close to the gasholder and between the gasholder and the hydrogen compressor to switch off the compressor meter in the event of the gasholder being emptied to the extent as to cause vacuum. 6. Purity of caustic soda.—The water and caustic soda used for making lye shall be chemically pure within pharmaceutical limits. 7. Precautions against reversal of polarity.—Electrical connections at the electrolyser cells and at the electric generator terminals shall be constructed as to preclude the possibility or wrong connections leading to the reversal of polarity and in addition an automatic device shall be provided to cut off power in the event of reversal of polarity owing to wrong connections either at the switch board of at the electric generator terminals. 8. Colouring of gas pipes.—Oxygen and hydrogen gas pipes shall be painted with distinguishing colours and in the event of leakage at the joints of the hydrogen gas pipe, the pipe after reconnection shall be purged of all air before drawing in hydrogen gas. 9. Use of flame proof fittings.—All electrical wiring and apparatus in the electrolyser room shall be of flame proof construction or enclosed in flameproof fittings and no naked light or flame shall be allowed to be taken either in the electrolyser room or where compression and filling of the gases is carried on and such warning notices shall be exhibited in prominent places, 10. Prohibition of hot work.—No part of the electrolyser plant and the gasholders and compressor shall be subjected to welding, brazing, soldering or cutting until steps have been taken to remove any explosive substance from that part and render the part safe for such operations and after the completion of such operations no explosive substance shall be allowed to enter that part until the metal has cooled sufficiently to prevent risk of explosion. 11. Repair etc. to be done under supervision.—No work or operation, repair or maintenance shall be undertaken except under the direct supervision of a person who, by his training, experience and knowledge of the necessary precautions against risk of explosion is competent to supervise such work. No electric generator after erection or repairs shall be switched on to the electrolyscrs unless the same is certified by the competent persons under whose direct supervision erection or repairs are carried on to be in a safe condition and the terminals have been checked for the polarity as required by Paragraph 7, 12. Checking of plant.—Every part of the electrolyser plant and the gasholders and compressor shall have a regular Schedule of overhaul and checking and every defect noticed shall be rectified forthwith. SCHEDULE XX PROCESS OF EXTRACTING OILS AND FATS FROM VEGETABLE AND ANIMAL SOURCE IN SOLVENT EXTRACTION PLANTS 1. Definitions.—For the purposes of this Schedule— (a) "Competent person" for the purpose of this Schedule shall be at least a Member of the Institution of Engineers (India) or an Associate Member of the said Institution with 10 years experience in a responsible position as may be approved by the Chief Inspector: Provided that a graduate in mechanical engineering or chemical engineering technology with specialized knowledge of oils and fats and with a minimum experience of 5 years in a solvent extraction plant shall also be considered to be a competent person: Provided further that the State Government may accept any other qualifications if in its opinion they arc equivalent to the qualifications aforesaid. (b) "flame proof enclosure" as applied to electrical machinery or apparatus means an enclosure that will withstand, when covers or other access doors are properly secured, an internal explosion of the flammable gas or vapour which may enter or which may originate inside the enclosure without suffering damage and without communicating internal inflammation (or explosion) to the external flammable gas or vapour; (c) "solvent" means an inflammable liquid such as pentane, hexane and heptane used for the recovery of vegetable oils; (d) "solvent extraction plant" means a plant in which the process of extracting oils and fats from vegetable and animal sources by the use of solvents is carried on. 2. Location and layout.—(1) No solvent extraction plant shall be permitted to be constructed or extended to within a distance of 30 meters from the nearest residential locality. (2) A 1-5 metre high continuous wire fencing shall be provided around the solvent extraction plant up to a minimum distance of 15 meters from the plant. (3) No person shall be allowed to carry any matches or an open flame of fire inside the area bound by the fencing. (4) Boiler houses and other buildings where open flame processes are carried on shall be located at least 30 metres away from the solvent extraction plant. (5) If godowns and preparatory processes are at a distance of less than 30 meters from the solvent extraction plant, these shall be at least 15 meters distant from the plant, and a continuous barrier wall of non-combustible material 1.5 meters high shall be erected at distance of not less than 15 meters from the solvent extraction plant so that it extends to at a least 30 meters of vapour travel around its ends from the plant to the possible sources of ignition. 3. Electrical installations.—(1) All electrical motors and wiring and either electrical equipment installed or housed in solvent extraction plant shall be of flame proof constructions. (2) All metal parts of the plant and building including various tanks and containers where solvents are stored are present and all parts of electrical equipment not required to be energised shall be properly bonded together and connected to earth so as to avoid accidental rise in the electrical potential of such parts above the earth potential. 4. Restrictions on smoking.—Smoking shall be strictly prohibited within 15 meters distance from solvent extraction plant. For this purpose, "No Smoking" signs shall be permanently displayed in the areas. 5. Precautions against friction.—(1) All tools and equipment including ladders, chains and other lifting tackle required to be used in solvent extraction plant shall be of non-sparking type. (2) No machinery or equipment in solvent extraction plant shall be belt driven. (3) No person shall be allowed to enter and work in the solvent extraction plant if wearing clothes made of nylon or such other fibre that can generate static electrical charge or wearing footwear which is likely to cause sparks by friction. 6. Fire-fighting apparatus.—(1) Adequate number of portable fire extinguisher suitable for use against flammable liquid fires shall be provided in the solvent extraction plant. (2) An automatic water spray sprinkler system on a wet pipe or open-head deluge system with sufficient supply of storage water shall be provided over solvent extraction plant and throughout the building housing such plant. 7. Precautions against power failure.—Provision shall be made for the automatic cutting off of steam in the event of power failure and also for emergency overhead water-supply for feeding water by gravity to condensers which shall come into play automatically with the power failure. 8. Magnetic separators.—Oil cake shall be fed to the extractor by a conveyor through a hopper and a magnetic separator shall be provided to remove any pieces of iron during its transfer. 9. Venting.—(1) Tanks containing solvents shall be protected with emergency venting to relieve excessive internal pressure in the event of fire. (2) All emergency relief vents shall terminate at least 6 metres above the ground and be so located that vapours will not re-enter the building in which solvent extraction plant is located. 10. Waste water.—Process waste water shall be passed through a flash evaporator to remove any solvent before it is discharged into a sump which should be located within the fenced area but not closer than eight metres to the fence. 11. Ventilation.—The solvent extraction plant shall be well ventilated and if the plant is housed in a building, the building shall be provided with mechanical ventilation with provision for at least six air changes per hour. 12. House-keeping.—(1) Solvent shall not be stored in an area covered by solvent extraction plant except in small quantities which shall be stored in approved safety cans. (2) Waste materials such as oily rags, other wastes and absorbents used to wipe off solvent and paints and oils shall be deposited in approved containers and removed from the premises at least once a day. (3) Space within the solvent extraction plant and within 15 meters from the plant shall be kept free from any combustible materials and any spills of oil or solvent, shall be cleaned up immediately. 13. Examination ami repairs.—(1) The solvent extraction plant shall be examined by the competent person to determine any weakness or corrosion and wear once in every 12 months. Report of such examination shall be supplied to the Inspector with his observation as to whether or not the plant is in safe condition to work. (2) No repairs shall be carried out to the machinery or plant except under the direct supervision of the competent person. (3) Facility shall be provided for purging the plant with inert gas before opening for cleaning or repairs and before introducing solvent after repairs. 14. Operating Personnel.—The operation of the plant and machinery in the solvent extraction plant shall be in the charge of such duly qualified and trained persons as are certified by the competent person to be fit for the purpose and no other person shall be allowed to operate the plant and machinery. 15. Employment of young persons-No young person shall be employed in the solvent extraction plant.19 15A-CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or young person may be employed in the solvent extraction plant with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath. 16. Vapour detection.—A suitable type of flame proof and portable combustible gas indicator shall be provided and maintained in good working order and a Schedule of routine sampling of atmosphere at various location approved by the Chief Inspector shall be drawn out and entered in a register maintained for the purpose. SCHEDULE XXI MANUFACTURE OR MANIPULATION OF MANGANESE AND ITS COMPOUNDS 1. Application.—This Schedule shall apply to every factory in which or in any part of which any manganese process is carried on. 2. Definitions.—For the purposes of this Schedule— (a) "efficient exhaust ventilation" means localized ventilation effected by mechanical means for the removal of dust or fume or mist at its source of origin so as to prevent it from escaping into the atmosphere of any place where any work is carried on. No drought shall be deemed to be efficient which fails to 19 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 remove the dust or fume or mist at the point where it is generated and fails to prevent it from escaping into and spreading into the atmosphere of a workplace; (b) "first employment" means first employment in any manganese process following any cessation of employment for a continuous period exceeding three calendar months; (c) "manganese process" means processing, manufacture or manipulation of manganese or any compound of manganese or any mixture containing manganese; and (d) "manipulation" means mixing, blending, filling, emptying, grinding, sieving, drying, packing, sweeping or otherwise handling of manganese, or a compound of manganese, or any ore or any mixture containing manganese. 3. Isolation of a process.—Every manganese process which may give rise to dust, vapour or mist containing manganese, shall be carried on in a totally enclosed system or otherwise effectively isolated from other processes so that other plants and processes and other parts of the factory and persons employed on other processes may not be effected by the same. 4. Ventilation of process.—No process in which any dust, vapour or mist containing manganese is generated, shall be carried out except under an efficient exhaust ventilation which shall be applied as near to the point of generation as practicable. 5. Personal protective equipment.—(1) The occupier of the factory shall provide and maintain in good and clean condition suitable overalls and head coverings for all persons employed in any manganese process and such overalls and head coverings shall be worn by the persons while working on a manganese process. (2) The occupier of the factory shall provide suitable respiratory protective equipment for use by workers in emergency to prevent inhalation of dust, fumes or mists. Sufficient number of complete sets of such equipment shall always be kept near the workplace and the same shall be properly maintained and kept always in a condition to be used readily. (3) The occupier shall provide and maintain for the use of all persons employed, suitable accommodation for the storage and make adequate arrangement for cleaning and maintenance of personal protective equipment. 6. Prohibition relating to young persons-No young person shall be employed or permitted to work in any manganese process.20 6A-CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or permitted to work in any manganese process with their consent to work subject conditions:-to the following (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall, as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath. 7. Food, drinks etc. prohibited in the workrooms.—No food, drink, pan and supari or tobacco shall be allowed to be brought into premises consumed by any worker in any workroom in which any manganese process is carried on. 8. Mess-room.—There shall be provided and maintained for the use of the persons employed in a manganese process a suitable mess-room which shall be furnished with sufficient tables and benches and adequate means for warming of food. The mess-room shall be placed under the charge of a responsible person and shall be kept clean. 9. Washing facilities.—There shall be provided and maintained in a clean state and in good condition, for the use of persons employed on manganese process— (a) a wash place under cover, with either— (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 centimeters for every ten such persons employed at any one time, and having a constant supply of water from tap or jet above the trough at intervals of not more than 60 centimeters; or 20 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 (ii) at least one wash basin for every five such persons employed at any one time, fitted with a waste pipe and plug and having a constant supply of water; and (b) sufficient supply of soap or other suitable cleaning materials and nail brushes and clean towels. 10. Cloak-room.—If the Chief Inspector so requires there shall be provided and maintained for the use of persons employed in manganese process a cloak-room for clothing, pui off during working hours with adequate arrangements for drying the clothing. 11. Cautionary placard and instructions.—Cautionary notices in the form specified in appendix and printed in the language of the majority of the workers employed, shall be affixed in prominent places in the factory where they can be easily and conveniently read by the workers and arrangement shall be made by the occupier to instruct periodically all workers employed in a manganese process regarding the health hazards connected with their duties and the best preventive measures and methods to protect themselves. The notices shall always be maintained in a legible condition. 12. Medical facilities and records of examination and tests.—(1) The occupier of every factory to which the Schedule applies, shall— (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 13. Medical examination by Certifying Surgeon.—(1) Every worker employed in any manganese process shall be medically examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for detection of serum calcium, serum phosphate and manganese in blood and urine and also include steadiness tests and other neuromuscular co-ordination tests. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified for such employment by the Certifying Surgeon. (2) Every worker employed in a manganese process shall be re-examined by a Certifying Surgeon at least once in every three calendar months and such examination shall, wherever the Certifying Surgeon considers appropriate include all the tests in sub-paragraph (1). (3) The Certifying Surgeon after examining a worker shall issue a Certificate of Fitness in Form 26. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The records of each examination carried out under sub-paragraphs (1) and (2) including the nature and the results of these tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that the worker is no longer fit for employment in the said process on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in these documents should also include the period for which he considers that the said person is unfit to work in the said process. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon after further examination, again certifies him fit for employment in those processes. 14. Exemption.—If in respect of any factory the Chief Inspector is satisfied that owing to any exceptional circumstances, or infrequency of the process or for any other reason, application of all or any of the provisions of this Schedule is not necessary for the protection of the persons employed in such factory he may, by an order in writing which he may at his discretion revoke, exempt such factory from all or any of the provisions on such conditions and for such period as he may specify in the said order. APPENDIX CAUTIONARY NOTICE Manganese and Manganese Compounds 1. Dust, Fumes and mists of manganese and its compounds are toxic when inhaled or when ingested. 2. Do not consume food or drinks near the workplace. 3. Take a good wash before taking meals. 4. Keep the working area clean. 5. Use the protective clothing and equipment provided. 6. When required to work in situations where dusts, fumes or mists are likely to be inhaled, use respiratory protective equipment provided for the purpose. 7. If you get severe headaches, prolonged sleeplessness or abnormal sensations on the body, report to the manager who would make arrangements for your examination and treatment. SCHEDULE XXII MANUFACTURE OR MANIPULATION OF DANGEROUS PESTICIDES 1. Application.—This Schedule shall apply in respect of all factories or any part thereof in which the process of manufacture or manipulation of dangerous pesticide hereinafter referred or as the said manufacturing process is carried on. 2. Definitions.—For the purposes of this Schedule— (a) "dangerous pesticides" means any product proposed or used for controlling, destroying or repelling any part or for preventing growth or mitigating excepts of such growth including any of its formulations which is considered toxic under and is covered by the Insecticides Act, 1968 and the rules made thereunder and any other product, as may be notified from time to time by the State Government; (b) "efficient exhaust draught" means localized mechanical ventilation for removal of smoke, gas vapour, dust, fume or mist so as to prevent them from escaping into the air of any workroom in which work is carried on. No exhaust draught shall be considered efficient if it fails to remove smoke generated at the point where such gas, fume, dust, vapour or mist originates from the process; (c) "first employment" shall mean first employment in any manufacturing process to which this Schedule applies and shall also include re-employment in the said manufacturing process following any cessation of employment for a continuous period exceeding three calendar months; and (d) "manipulation" including mixing, blending, formulating, filling, emptying, packing or otherwise handling. 3. Instruction to workers.—Every worker on his first employment shall be fully instructed on the properties including dangerous properties of the chemicals handled in the said manufacturing process and the hazards involved. The employees shall also be instructed in the measures to be taken to deal with any emergency, such instructions shall be repeated periodically. 4. Cautionary notice and placards.—Cautionary notices and placards in the form specified in appendix to this Schedule and printed in the language of the majority of the workers shall be displayed in all workplaces in which the said manufacturing process is carried on so that they can be easily and conveniently read by the workers. Arrangements shall be made by the occupier and the manager of the factory to periodically instruct the workers regarding the health hazards arising in the said manufacturing process and methods of protection. Such notices shall include brief instructions regarding the periodical clinical tests required to be undertaken for protecting health of the workers. 5. Prohibition relating to employment of young persons-No young person shall be employed or permitted to work in any room in which the said manufacturing process is carried on or in any room in which dangerous pesticide is stored21. 5A- CONDITION OF EMPLOYMENT OF WOMEN-Women workers may be employed or permitted to work in any room in which the said manufacturing process is carried on or in any room in which dangerous pesticide is stored with their consent to work subject to the following conditions:- (1) International Safety standards shall be adopted by the occupier for providing Occupational Safety and Health (OSH). (2) The occupier shall. as far as possible, modernise the above processes/places from time to time and will use modern equipments. (3) Pregnant and breast feeding women shall not be employed or permitted to work at a bath. 21 Provisions of clause (3) of Article 348 of the Constitution of India, the Governor is pleased to order the publication of the following English translation of notification no. 963/XXXV1-03-2025-1792147, dated July 4, 2025 6. Food, drinks and smoking prohibited.—(1) No food, drink, tobacco, pan or supari shall be brought into or consumed by any worker in any workroom in which the said manufacturing process is carried out. (2) Smoking shall be prohibited in any workroom in which the said manufacturing process is carried out. 7. Protective clothing and protective equipment.—(1) Protective clothing consisting of long pants and shirts or overalls with long sleeves and head coverings shall be provided for all workers employed in the said manufacturing process. (2) (a) Protective equipment consisting of rubber gloves, gum boots, rubber apron, chemical safety goggles and respirators shall be provided for all workers employed in the said manufacturing process. (b) Gloves, boots, aprons shall be made from synthetic rubber where a pesticide contains oil. (3) Protective clothing and equipment shall be worn by workers supplied with such clothing and equipment. (4) Protective clothing and equipment shall be washed daily inside and outside if the workers handle pesticides containing nicotine or phosphorus and shall be washed frequently if handling other pesticides. (5) Protective clothing and equipment shall be maintained in good repair. 8. Floors and workbenches.—(1) Floors in every workroom where dangerous pesticides are manipulated shall be of cement or other impervious material giving a smooth surface. (2) Floors shall be maintained in good repair, provided with adequate slope leading to a drain and thoroughly washed once a day with hose pipe. (3) Workbenches where dangerous pesticides are manipulated shall be made of smooth, non-absorbing material preferably stainless steel and shall be cleaned at least once daily. 9. Spillage and waste.—(1) If a dangerous pesticide during its manipulation splashes or spills on the work-bench, floor or on the protective clothing worn by a worker, immediate action shall be taken for thorough decontamination of such areas or articles. (2) Cloth, rags, paper or other material soaked or soiled with a dangerous pesticide shall be deposited in a suitable receptacle with tight fitting cover. Contaminated waste shall be destroyed by burning at least once a week. (3) Suitable deactivating agents where available shall be kept in a readily accessible place for use while attending to a spillage. (4) Easy means of access shall be provided to all parts of the plants for cleaning, maintenance and repairs. 10. Empty containers used for dangerous pesticides.—Containers used for dangerous pesticides shall be thoroughly cleaned of their content and treated with an in-activating agent before being discarded or destroyed. 11. Manual handling.—(1) A dangerous pesticide shall not be required or allowed to be manipulated by hand except by means of a long handled scoop. (2) Direct contact of any part of the body with a dangerous pesticide during its manipulation shall be avoided. 12. Ventilation.—(1) In every workroom or area whereas dangerous pesticide is manipulated, adequate ventilation shall be provided at all times by the circulation of fresh air. (2) Unless the process is completely enclosed the following operations during manipulation of a dangerous pesticide shall not be undertaken without an efficient exhaust draught— (a) empty a container holding a dangerous pesticide; (b) blending a dangerous pesticide; (c) preparing a liquid or powder formulation containing a dangerous pesticide; and (d) changing or filling a dangerous pesticide into a container, tank, hamper or machines or small sized containers, (3) In the event of a failure of the exhaust draught provided on the above operation, the said operations shall be stopped forthwith. 13. Time allowed for washing.—(1) Before each meal and before the end of the day's work at least ten minutes in addition to the regular rest interval shall be allowed for washing to each worker engaged in the manipulation of dangerous pesticide. (2) Every worker engaged in the manipulation of dangerous pesticides shall have a thorough wash before consuming any food and also at the end of the day's work. 14. Washing and bathing facilities.—(1) There shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the factory where the said manufacturing process is carried on adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 5 persons employed. (2) The washing places shall have standpipes placed at intervals of not less than one meter. (3) Not less than one half of the total number of washing places shall be provided with bathrooms. (4) Sufficient supply of clean towels made of suitable material shall be provided: Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 15. Cloak-room.—There shall be provided and maintained for the use of all workers employed in the factory where the said manufacturing process is carried on— (a) a cloak-room for clothing put off during working hours with adequate arrangements for drying clothing if wet; and (b) separate and suitable arrangements for the storage of protective clothing provided under Paragraph 7. 16. Mess-room.—(1) There shall be provided and maintained for the use of all workers employed in the factory in which the said manufacturing process is carried on and remaining on the premises during the rest intervals a suitable mess-room which shall be furnished with— (a) sufficient tables and benches with back rest; and (b) adequate means for warming food. (2) The mess-room shall be placed under the charge of a responsible person and shall be kept clean. 17. Manipulation not to be undertaken.—Manufacture or manipulation of a pesticide shall not be undertaken in any factory unless a certificate regarding its dangerous nature or otherwise is obtained from the Chief Inspector. 18. Medical facilities and records of examinations and tests.—(1) The occupier of every factory to which the Schedule applies, shall— (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories which shall be kept readily available for inspection by the Inspector. 19. Examined by the Certifying Surgeon.—(1) Every worker employed in the processes mentioned in Paragraph 1 shall be examined by the Certifying Surgeon within 15 days of his first employment. Such examination in respect of Halogenated pesticides, shall include tests for determination of the chemical in blood and in fat tissues, EEG abnormalities and memory tests, in respect of organo phosphorous compounds, such examinations shall include test for depression of cholinesterase in plasma and red blood cells. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every six calendar months and such examination shall, wherever the Certifying Surgeon, (sic)80. The record of each examination carried out under sub-paragraphs (1). Further every worker employed in the said processes shall also be examined once in every three months by the factory medical officer. (3) The Certifying Surgeon after examining a worker, shall issue a certificate of Fitness in Form 26. The record of examination and re-examination carried out shall be entered in the certificate and the certificate shall be kept in the custody of manager of the factory. The record of each examination carried out under sub- paragraph (1) and (2), including the nature and the results of these tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit to work in the said processes. (6) No person who has been found unfit to work as said in sub-paragraph (5) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon after further examination again certifies him fit for employment in those processes. 20. Exemption.—If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstances or the infrequency of the said manufacturing process or for any other reason which he shall record in writing all or any of the provisions of this Schedule are not necessary for the protection of the workers employed in the factory, he may by a certificate in writing exempt such factory, from all or any of the provisions on such condition as he may specify therein, such certificate may at any time be revoked by the Chief Inspector after recording his reasons therefor. APPENDIX CAUTIONARY NOTICE Insecticides and Pesticides 1. Chemicals handled in this plant are poisonous substances. 2. Smoking, eating food or drinking, chewing tobacco in this area is prohibited. No foodstuff or drink shall be brought in this area. 3. Some of those chemicals may be absorbed through skin and may cause poisoning. 4. A good wash shall be taken before meals. 5. A good bath shall be taken at the end of the shift. 6. Protective clothing and equipment supplies shall be used while working in this area. 7. Containers of pesticides shall not be used for keeping foodstuffs. 8. Spillage of the chemicals on any part of the body or on the floor or work-bench be immediately washed away with water. 9. Clothing contaminated due to splashing shall be removed immediately. 10. Scrupulous cleanliness shall be maintained in the area. 11. Do not handle pesticides with bare hands, use scoops provided with handle. 12. In case of sickness like nausea, vomiting, giddiness, the manager should be informed who shall make necessary arrangements for treatment. 13. All workers shall report for the prescribed medical tests regularly to protect their own health. SCHEDULE XXIII MANUFACTURING PROCESS OR OPERATIONS IN CARBON DISULPHIDE PLANTS 1. Application. This Schedule shall apply to all electric furnaces in which carbon disulphide is generated and all other plants where carbon disulphide after generation, is condensed, refined and stored. This Schedule is in addition to and not in derogation of any of the provisions of the Act and Rules made thereunder. 2. Construction, Installation and Operation. (1) The buildings in which electric furnaces area installed and carbon disulphide after generation is condensed and refined shall be segregated from other parts of the factory and shall be of open type to ensure optimum ventilation and the plant layout shall be such that only a minimum number of workers are exposed to the risk of any fire or explosion at any one time. (2) Every electric furnace and every plant in which carbon disulphide is condensed, refined and stored with all their fittings and attachments shall be of good construction, sound material and of adequate strength to sustain the internal pressure to which, furnace or the plant may be subjected to, and shall be so designed that carbon disulphide liquid and gas are in closed system during their normal working. (3) The electric fumace supports shall be firmly grouted about 60 centimeters in concrete or by other effective means. (4) Every electric fumace shall be installed and operated according to manufacturers' instructions and these instructions shall be clearly imparted to the personnel incharge of construction and operation. (5) The instructions regarding observance of correct furnace temperature, sulphur dose, admissible current, or power consumption, and periodical checking of charcoal level shall be strictly complied with. 3. Electrodes. (1) Where upper ring electrodes made of steel are used in the electric furnace, they shall be of seamless tube construction and shall have arrangement for being connected to cooling water system through a siphon built in the electrodes or though a positive pressure water pump. (2) The arrangement for cooling water referred to in sub-paragraph (1) shall be connected with automatic alarm system which will actuate in the event of interruption of cooling water in the electrodes and give visible and audible alarm signals in the control room and simultaneously stop power supply for the furnace operation and stop the future supply of water. The alarm system and the actuating device shall be checked every day. 4. Maintenance of charcoal level. When any electric furnace is in operation, it shall be ensured that the electrodes are kept covered with charcoal bed. 5. Rupture disc and safety seal. At least two rupture discs be fitted on the off take pipe between the electric furnace and sulphur separator to prevent entry of pieces of charcoal into the condensers and piping. 6. Rupture disc and safety seal. (1) At least two rupture discs of adequate size which shall blow off at a pressure twice the maximum operating pressure shall be provided on each furnace and shall either be mounted directly on the top of the furnace or each through an independent pipe as close as possible to the furnace. (2) The safety water shall be provided and tapped from a point between the charcoal separator and the sulphur separator. 7. Pyrometer and manometers. (1) Each electric furnace shall be fitted with adequate number of pyrometers to give an indication of the temperature as correctly as reasonably practicable at various points in the furnace. The dials for reading the temperatures shall be located in the control room. (2) Manometers or any other suitable devices shall be provided for indicating pressure- (a) in the off take pipe before and after the sulphur separator; and (b) in primary and secondary condensers. 8. Check valves. All piping carrying carbon disulphide shall be fitted with check valves at suitable positions so as to prevent gas from flowing back into any electric furnace in the event of its shut down. 9. Inspection and maintenance of electric furnaces. (1) Every electric furnace shall be inspected internally by a competent person- (a) before being placed in service after installation; (b) before being placed in service after reconstruction or repairs; and (c) periodically every time the furnace is opened for cleaning or de-ashing or for replacing electrodes. (2) When an electric furnace is shut down for cleaning or de-ashing- (a) the brick lining shall be checked for continuity and any part found defective be removed; (b) after removal of any part of the lining referred to in (a), the condition of the shell be closely inspected; and (c) any of the plate forming shell found corroded to the extent that safety of the furnace is endangered shall be replaced. 10. Maintenance of records. The following hourly records shall be maintained in a log book- (a) manometer readings at the points specified in sub-paragraph (2) of Paragraph 7; (b) gas temperature indicated by pyrometers and all other vital points near the sulphur separator and primary and secondary condensers; (c) water temperature and flow of water through the siphon in the electrodes; and (d) primary and secondary voltage and current and energy consumed. 11. Electrical apparatus wiring and fittings. All building in which carbon disulphide is refined or stored shall be provided with electrical apparatus, wiring and fittings which shall afford adequate protection from fire and explosion. 12. Prohibition relating to smoking.-No person shall smoke or carry matches, fire or naked light or other means of producing a naked light or spark in buildings in which carbon disulphide is refined or stored, and a notice in the language understood by a majority of the workers shall be pasted in the plant prohibiting smoking and carrying of matches, fire or naked light or other means of producing naked or spark into such rooms. 13. Means of escape. Adequate means of escape shall be provided and maintained to enable persons to move to a safe place as quickly as possible in case of an emergency. At least two independent staircases of adequate width shall be provided in every building housing the furnaces of reasonable intervals at opposite ends. These shall always be kept clean of all obstructions and so designed as to afford easy passage. 14. Warnings in case of fire. There shall be adequate arrangements for giving warning in case of fire or explosion which shall operate on electricity and in case of failure of electricity, by some mechanical means. 15. Fire-fighting equipment. (1) Adequate number of suitable fire extinguishers or other fire-fighting equipment shall be kept in constant readiness for dealing with risks involved and depending on the amount and nature of materials stored. (2) Clear instructions as to how the extinguishers or other equipment should be used printed in the language which the majority of the workers employed understand, shall be affixed to each extinguisher or other equipment and the personnel trained in their use. 16. Bulk sulphur. (1) Open or semi-enclosed spaces for storage of bulk sulphur shall be sited with due regard to the dangers which may arise from sparks given off by near locomotives etc. and precautions shall be taken to see that flame, smoking and matches and other sources of ignition do not come in contact with the clouds of dust arising during handling of bulk sulphur. (2) All enclosures for bulk sulphur shall be of non-combustible construction, dust may lodge. adequately ventilated and so designed as to provide a minimum of lodges on which (3) The bulk sulphur in the enclosures shall be handled in such a manner as to minimise the formation of dust clouds and no flame smoking and matches or other sources of ignition shall be employed during handling, and non-speaking toll shall be used whenever sulphur is shovelled or otherwise removed by hand. (4) No repairs involving flames, heat or use of hand or power tools shall be made in the enclosures where bulk sulphur is stored. 17. Liquid sulphur. Open flames, electric sparks and other sources of ignition, including smoking and matches, shall be excluded from the vicinity of molten sulphur. 18. Training and supervision. (1) All electric furnaces and all plants in which carbon disulphide is condensed, refined or stored shall be under adequate supervision at all times while the furnaces and plants are in operation. (2) Workers in charge of operation and maintenance of electric furnaces and the plants shall be properly qualified and adequately trained. 19. Washing facilities. (1) The occupier shall provide and maintain in a clean state and in good repair, for the use of all persons employed wash place under cover with at least one tap or stand-pipe, having a constant supply of clean water for every five such persons, the taps or stand-pipe being spaced not less than 120 centimeters apart with a sufficient supply of soap and clean towels, provided that towels shall be supplied individually to each worker if so ordered by the Inspector. (2) All the workers employed in the sulphur storage, handling and melting operations shall be provided with a nail brush. 20. Personal protective equipments. (1) Suitable goggles and protective cloth consisting of overalls without pockets, gloves and footwear shall be provided for the use of operator: (a) when operating valves or cocks controlling fluids etc; (b) drawing-off of molten sulphur from sulphur pots; and (c) handling charcoal or sulphur. (2) Suitable respiratory protective equipment shall be provided and stored in the appropriate place for use during abnormal conditions in an emergency. (3) Arrangements shall be made for proper and efficient cleaning of all such protective equipments. 21. Cloak-rooms. There shall be provided and maintained for the use of all workers employed in the processes, a suitable cloak-room for clothing put-off during work hours and a suitable place separate from the cloak-room for the storage of overalls of working clothes. The accommodation so provided shall be placed in the charge of a responsible person and shall be kept clean. 22. Unauthorised persons. Only maintenance and repair personnel, persons directly, connected with the plant operation and those accompanied by authorised persons shall be admitted into the plant. SCHEDULE XXIV OPERATIONS INVOLVING HIGH NOISE LEVELS 1. Application. This Schedule shall apply to all operations in any manufacturing process which have high noise levels. 2. Definitions. For the purpose of this Schedule- (a) "A-weighting" means making graded adjustments in the intensities of sound of various frequencies for the purpose of noise measurement, so that the sound pressure level measured by an instrument reflects the actual response of the human ear to the sound measured; (b) "dBA" refers to sound level in decibels as measured on a sound level meter operating on the A-weighting network with slow meter response (c) "decibel" means one-tenth of "Bel" which is the fundamental division of a logarithmic scale used to express the ratio of two specified or implied quantities, the number of "Bels" denoting such a ratio being the logarithm to the base of 10 of this ratio. The noise level (or the sound pressure level) corresponds to reference pressure of six x 10 newtone per square meter or 0.0002 dynes per square centimeter which is the threshold of hearing, that is, the lowest sound pressure level necessary to produce the sensation of hearing in average healthy listeners. The decibel in abbreviated form is dB; (d) "first employment" shall mean first employment in areas where the noise exceeds the maximum permissible exposure levels specified in sub-paragraph (1) of paragraph 3 and shall also include re-employment in the said areas following any cessation of employment for a continuous - period exceeding three calendar months; (e) "frequency" is the rate of pressure variations expressed in cycles per second or hertz; (f) "high noise level" means any noise level measured on the A-weighted scale is 90 dB or above; and (g) "noise" means any unwanted sound. 3. Protection against noise. (1) In every factory, suitable engineering control or administrative measures shall be taken to ensure, so far as is reasonably practicable, that no worker is exposed to sound levels exceeding the maximum permissible noise exposure levels specified in Tables 1 and 2. TABLE 1 PERMISSIBLE EXPOSURE IN CASES OF CONTINUOUS NOISE Total time of exposure (continuous or a number of short-term exposure) per day, in Sound pressures level in dBA hours 8 90 6 92 4 95 3 97 2 100 1-1/2 102 1 105 ¾ 107 ½ 110 ¼ 115 Notes. (1) No exposure in excess of 115 dBR is to be permitted. (2) For any period of exposure falling in between any figure and the next higher or lower figure as indicated in column 1, the permissible sound pressure level is to be determined by extrapolation on a proportionate basis. TABLE 2 PERMISSIBLE EXPOSURE LEVELS OF IMPLOSIVE OR IMPACT NOISE Peak sound pressure level in dB Permitted number of impulses or im-pacts per day 140 100 135 315 130 1000 125 3160 120 10000 Notes. (1) No exposure in excess of 140 dB peak sound pressure level is permitted. (2) For any peak sound pressure level falling in between any figure and the next higher or lower figure as indicated in Column 1, the permitted number of impulses or impacts per day is to be determined by extrapolation on a proportionate basis. (3) For the purposes of this Schedule, if the variations in the noise level involve maxima at intervals of one second or less, the noise is to be considered as a continuous one and the criteria given in Table 1 would apply. In other cases, the noise is to be considered as impulsive or impact noise and the criteria given in Table 2 would apply. (4) When the daily noise exposure is composed of two or more periods of noise exposure at different levels their combined effect should be considered, rather than the individual effect of each. The mixed exposure should be considered to exceed the C1+C2 Cn limit value if the sum of the fractions T1+T2 Tn excess unity-where the C1, C2, etc. indicated the total time or actual exposure at a specified noise level and T1, T2, etc. denote the time of exposure permissible at that level. Noise exposure of less than 90 dBA may be ignored in the above calculation. (5) Where it is not possible to reduce the noise exposure to the levels specified in sub-rule (1) by reasonably practicable engineering control or administrative measure, the noise exposure shall be reduced to the greatest extent feasible by such control measures and each worker so exposed shall be provided with suitable ear protectors so as to reduce the exposure to noise to the levels specified in sub-rule (1). (6) Where the ear protectors provided in accordance with sub-paragraph (2) and worn by a worker cannot still attenuate the noise reaching near his ear, as determined by subtracting the attenuation value in dBA of the ear protectors concerned from the measured sound pressure level, to a level permissible under Table 1 or Table 2 as the case may be, the noise exposure period shall be suitably reduced to correspond to the permissible noise exposure specified in sub-paragraph (1). (7) (a) In all cases where the prevailing sound levels exceeds the permissible levels specified in sub-paragraph (1) there shall be administered an effective hearing conservation programme which shall include among other hearing conservation measures, pre-employment and periodical auditory surveys conducted on workers exposed to noise exceeding the permissible levels, and rehabilitation of such workers either by reducing the exposure to the noise levels or by transferring them to places where noise levels are relatively less or by any other suitable means. (b) Every worker employed in areas where the noise exceeds the maximum permissible exposure levels specified in sub-rule (1) shall be subjected to an auditory examination by a Certifying Surgeon within 14 days of his first employment and thereafter, shall be re- examined at least once in every 12 months. Such initial and periodical examinations shall include tests which the Certifying Surgeon may consider appropriate, and shall include determination of auditory thresholds for pure tones of 125, 250, 500, 1000, 2000, 4000 and 8000 cycles per second. SCHEDULE XXV MANUFACTURE OF RAYON BY VISCOSE PROCESSES 1. Definitions. For the purposes of this Schedule- (a) "Approved" means approved for the time being in writing by the Chief Inspector; (b) "breathing apparatus" means a helmet or face piece with necessary connection by means of which the person using it in poisonous, as phyxioating or irritant atmosphere breathes unpolluted air, or any other approved apparatus; (c) "churn" means the vessel in which alkali cellulose pulp is treated with carbon disulphide; (d) "dumping" means transfer of cellulose xenthate from a dry churn to dissolve; (e) "efficient exhaust draught" means localised ventilation by mechanical means for the removal of any gas or vapour, so as to prevent it from escaping into the air of any place in which work is carried on. No draught shall be deemed to be efficient if it fails to control effectively any gas or vapour generated at the point where such gas or fume originate; (f) "first employment" shall mean first employment in the fume process and shall also include re-employment in the said process following any cessation of employment for a continuous period exceeding three calendar months; (g) "fume process" means any process in which carbon disulphide or hydrogen sulphide is produced, used or given off; (h) "life belt" means a belt made of leather or other suitable material which can be securely fastened round the body with a suitable length of rope attached to it, each of which is sufficiently strong to sustain the weight of a man; and (i) "protective equipment" means apron, goggles, face shields, footwear, gloves and overalls made of suitable materials. 2. Ventilation. (1) In all workrooms where a fume process is carried on, adequate ventilation by natural or mechanical means shall be provided so as to control, in association with other control measures, the concentration of carbon-disulphide and hydrogen sulphide in the air of every work environment, within the permissible limits. (2) Notwithstanding the requirements in sub-paragraph (1) an efficient exhaust draught shall be provided and maintained to control the concentration of carbon-disulphide and hydrogen sulphide in the air at the following locations- (a) dumping hoppers of dry churns; (b) spinning machines; (c) trio-rollers and cutters used in staple fibre spinning, (d) hydro-extractors for yarn cakes; (e) after treatment processes; and (f) spin baths. (3) Insofar as the spinning machine and trio-roller and cutters used in staple fibre spinning are concerned, they shall be, for the purpose of ensuring the effective-ness of the exhaust draught to be provided as required in sub-paragraph (1), enclosed as fully as practicable and provided with suitable shutters in sections to enable the required operations to be carried out without giving rise to undue quantities of carbon-di-sulphide and hydrogen sulphide escaping to the work environment. (4) No dry churn shall be opened after completion of reaction without initially exhausting the residual vapours of carbon-di-sulphide by operation of a suitable and efficient arrangement for exhausting the vapours which shall be continued to be operated so long as the churn is kept opened. (5) Whenever any ventilation apparatus normally required for the purpose of meeting the requirements is sub-paragraphs (2), (3) and (4) is ineffective, fails or is stopped for any purpose whatsoever, all persons shall be required to leave the work areas where the equipment or processes specified in the abovesaid sub-paragraphs are in use, as soon as possible and in any case not later than 15 minutes after such occurrence. (6)(i) All ventilation systems provided for the purposes as required in sub-para-graphs (2), (3) and (4) shall be examined and inspected once every week by a respon-sible person, it shall be thoroughly examined and tested by a competent person once in every period of 12 months. Any defects found by such examination or test shall be rectified forthwith. (ii) A register containing particulars of such examination and tests, and the state of the systems and the repairs or alternations (if any) found to be necessary shall be kept and shall be available for inspection by an Inspector. 3. Waste from spinning machines. Waste yarn from the spinning machines shall be deposited in suitable containers provided with close fitting covers. Such waste shall be disposed of quickly as possible after decontamination. 4. Lining of Dry Churns. The inside surface of all dry churns shall be coated with a non- sticky paint so that cellulose xanthate will not stick to the surface of the churn. Such coating shall be maintained in a good condition. 5. Air monitoring. (1) To ensure the effectiveness of the control measures, monitoring of carbon-disulphide and hydrogen sulphide in air shall be carried out once at least in every shift and the record of the results so obtained shall be entered in a register specially maintained for the purpose. (2) For the purpose of the requirement in sub-paragraph (1), instantaneous gas detector tubes shall not be used. Samples shall be collected over a duration of not less than 10 minutes and analysed by an approved method. The locations where such monitoring is to be done shall be as directed by the Inspector. (3) If the concentration of either carbon-disulphide or hydrogen sulphide exceeds the permissible limits for such vapour or gas as laid down in Second Schedule appended to Section 41-F of the Act, suitable steps shall be taken for controlling the concentration in air of such occurrence. 6. Prohibition to remain in fume process room. No person during his intervals for meal, or rest shall remain in any room wherein fume process is carried on. 7. Prohibition relating to employment of young persons.--No young person shall be employed or permitted to work in any fume process or in any room in which any such process is carried on. 8. Protective equipments. (1) The occupier shall provide and maintain in good condition protective equipments as specified in the table for use of persons employed in the processes referred to therein. TABLE Process Protective equipment 1. Dumping Overalls, face-shields, gloves and foot- wear-all made of suitable material. 2. Spinning Suitable aprons, gloves and footwear. 3. Process involving or likely to involve contact with viscose solution Suitable gloves and footwear. 4. Handling of sulphuric acid Suitable chemical goggles. 5. Any other process involving contact with hazardous chemicals Protective equipment as may be directed by the Chief Inspector by an order in writing. (2) A suitable room, rooms or lockers shall be provided exclusively for the storage of all the protective equipment supplied to workers and no such equipment shall be stored at any place other than the room, rooms or lockers so provided. 9. Breathing apparatus. (1) There shall be provided in every factory where fume process is carried on sufficient supply of- (a) breathing apparatus; (b) oxygen and suitable appliances for its administration; and (c) life belts. (2) (i) The breathing apparatus and other appliances referred to in sub-paragraph (1) shall be maintained in good condition and kept in appropriate locations so as to be readily available. (ii) The breathing apparatus and other appliances referred to in clauses (a) and (b) of sub- paragraph (1) shall be cleaned and disinfected at suitable intervals and thoroughly inspected once every month by a responsible person. (iii) A record of the maintenance and of the condition of the breathing apparatus and other appliances referred to in sub-clause (1) shall be entered in a register provided for that purpose which shall be readily available for inspection by an Inspector. (3) Sufficient number of workers shall be trained and periodically, retained in the use of breathing apparatus and administering artificial respiration so that at least 2 such trained persons would be available during all the working hours in each room in which fume process is carried on. (4) Breathing apparatus shall be kept properly labelled in clean, dry, lightproof cabinets and if liable to the effect by fumes, shall be protected by placing them in suitable containers. (5) No person shall be employed to perform any work specified in sub-para-graph (1) for which breathing apparatus is necessary to be provided under that sub-paragraph unless he has been fully instructed in the proper use of that equipment. (6) No breathing apparatus provided in pursuance of sub-paragraph (1) which has been worn by a person shall be worn by another person unless it has been thoroughly cleaned and disinfected since last being worn and the person has been fully instructed in the proper use of that equipment. 10. Electric fittings. All electric fittings in any room in which carbondisulphide other than a spinning room shall be of flame-proof construction and all electric conductors shall either be enclosed in metal conduit or be lead-sheated. 11. Prohibition relating to smoking etc. No person shall smoke or carry matches, fire or naked light or other means of producing naked light or spark in a room in which fume process is carried on. A notice in the language understood by the majority of the workers shall be posted in prominent locations in the plant prohibiting smoking and carrying of matches, fire or naked light or other means of producing naked light or spark into such rooms: Provided that fire, naked light or other means of producing naked light or spark may be carried on in such room only when required for the purposes of the process itself under the direction of a responsible person. 12. Washing and bathing facilities. (1) There shall be provided and maintained in a clean state and in good repair for the use of all workers employed in the processes covered by the Schedule, adequate washing and bathing places having a constant supply of water under cover at the rate of one such place for every 25 persons employed. (2) The washing places shall have standpipes placed at intervals of less than one meter. (3) Not less than one half of the total number of washing places shall be provided with bathrooms.: (4) Sufficient supply of clean towels made of suitable material shall be provided Provided that such towels shall be supplied individually for each worker if so ordered by the Inspector. (5) Sufficient supply of soap and nail brushes shall be provided. 13. Rest room. (1) A rest room shall be provided for the workers engaged in doffing operations of filament yarn spinning process. (2) Such rest room shall be provided with fresh air supply and adequate seating arrangement. 14. Cautionary notice and instructions. (1) The following cautionary notice shall be prominently displayed in each fume process room. Cautionary Notice 1. Carbon-disulphide (C; S) and Hydrogen sulphide (H; S) which may be present in this room are hazardous to health. 2. Follow safety instructions. 3. Use protective equipment and breathing apparatus as and when required. 4. Smoking is strictly prohibited in this area. This notice shall be in a language understood by the majority of the workers and displayed where it can be easily and conveniently read. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so displayed. (2) Arrangements shall be made to instruct each worker employed in any room in which a fume process is carried on regarding the health hazards connected with their work and the preventive measures and methods to protect themselves. Such instructions shall be given on his first employment and repeated periodically. (3) Simple and special instructions shall be framed to ensure that effective measures will be carried out in case of emergency involving escape of carbon-disul-phide and hydrogen sulphide. These instructions shall be displayed in the concerned areas and workers shall be instructed and trained in the actions to be taken in such emergencies. 15. Medical facilities and records of examinations and tests. (1) The occupier of each factory to which this Schedule applies, shall- (a) employ a qualified medical officer for medical surveillance of the workers employed in the fume process whose employment shall be subject to the approval of the Chief Inspector of Factories; and (b) provide to the said medical officer all the necessary facilities for the purpose referred to in clause (a). (2) The record of medical examination and appropriate tests carried out by the said medical officer shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 16. Medical examination by the Certifying Surgeon.-(1) Every worker employed in the fume process shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for estimation of exposure co-efficient (iodineazide test on urine), and cholesterol as well as Electrocardiogram (ECG) and Central Nervous System (CNS) tests. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the fume process shall be re-examined by a Certifying Surgeon at least once in every twelve calendar months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub- paragraph (1). (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the Manager of the Factory. The record of each examination carried out under sub-paragraphs (1) and (2), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be kept readily available for inspection by the Inspector. (5) If at any time the Certifying Surgeon is of opinion that a worker is no longer fit for employment in the fume process on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the Health Register. The entry of his findings in those documents should also include the period for which he considers that the said person is unfit for work in the fume process. (6) No person who has been found unfit to work as said in sub-paragraph (5) above shall be re-employed or permitted to work in the fume process unless the Certifying Surgeon, after further examination again certifies him fit for employment in such process. 17. Exemption. If in respect of any factory, the Chief Inspector is satisfied that owing to the exceptional circumstance or infrequency of the processes or for any other reason, all or any of the provisions of this Schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. SCHEDULE XXVI HIGHLY FLAMMABLE LIQUIDS AND FLAMMABLE COMPRESSED GASES 1. Application. These rules will be applicable to all factories where highly flammable liquid or flammable compressed gases are manufactured, stored, handled or used. 2. Definitions. For the purposes of this Schedule- (a) "flammable compressed gas" means flammable compressed gas as defined in Section 2 of the Static and Mobile Pressure Vessels (Unfired) Rules, 1981 framed under the Explosives Act, 1984; and (b) "highly flammable liquid" means any liquid including its solution, emulsion or suspension which when tested in a manner specified by Sections 14 and 15 of the Petroleum Act, 1934 (Act No. 30 of 1934), gives off flammable vapours at temperature less than 32 degrees centigrade. 3. Storage. (1) Every flammable liquid or flammable compressed gas used in every factory shall be stored in suitable fixed storage tank, or in suitable closed vessel located in a safe position under the ground, in the open or in a store room of adequate fire resistant construction. (2) Except as necessary for use, operation or maintenance, every vessel or tank which contains or had contained a highly flammable liquid or flammable compressed gas shall be always kept closed and all reasonably practicable steps shall be taken to contain or immediately drain off to a suitable container any spill or leak that may occur. (3) Every container, vessel, tank, cylinder, or store room used for storing highly flammable liquid or flammable compressed gas shall be clearly and in bold letters marked "Danger-Highly Flammable Liquid" or "Danger-Flammable Compressed Gas". 4. Enclosed systems for conveying highly Flammable Liquids. Wherever it is reasonably practicable, highly flammable liquids shall be conveyed within a factory in totally enclosed systems consisting of pipelines, pumps and similar appliances from the storage tank or vessel to the point of use. Such enclosed system shall be so designed, installed, operated and maintained as to avoid leakage or the risk of spilling. 5. Preventing formation of Flammable Mixture with Air. Wherever there is a possibility for leakage or spill of highly flammable liquid or flammable compressed gas from an equipment, pipeline, valve, joint or other part of a system, all practicable measures shall be taken to contain, drain-off or dilute such spills or leakage as to prevent formation of flammable mixture with air. 6. Prevention of Ignition.-(1) In every room, work place or other location where highly flammable liquid or flammable compressed gas is stored, conveyed, handled or used or where there is danger of fire or explosion from accumulation of highly flammable liquid or flammable compressed gas in air, all practicable measures shall be taken to exclude the sources of ignition. Such precautions shall include the following- (a) all electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition; (b) effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent; (c) no person shall wear or be allowed to wear any footwear having iron or steel nails or any other exposed ferrous material which is likely to cause sparks by friction; (d) smoking, lighting or carrying of matches, lighters or smoking material shall be prohibited; (e) transmission belts with iron fasteners shall not be used; and (f) all other precautions, as are reasonably practicable shall be taken to prevent initiation of ignition from all other possible sources such as open flames, all frictional sparks overheated surface of machinery or plant, chemical or physical-chemical reaction and radiant heat. 7. Prohibition of smoking. No person shall smoke in any place where highly flammable liquid or flammable compressed gas is present in circumstances that smoking would give rise to a risk of fire. The occupier shall take all practicable measures to ensure compliance with this requirement including display of a bold notice indicating prohibition of smoking, at every place where this requirement applies. 8. Fire Fighting. In every factory where highly flammable liquid or flammable compressed gas is manufactured, stored, handled or used, appropriate and adequate means of fighting a fire shall be provided. The adequacy and suitability of such means which expression includes the fixed and portable fire extinguishing systems, extinguishing material, procedures and the process of fire-fighting, shall be to the standards and levels prescribed by the Indian Standards applicable, and in any case not inferior to the stipulation under Rule 61. 9. Exemptions. If in respect of any factory, the Chief Inspector is satisfied that owing the exceptional circumstances of infrequency of the processes or for any other reason, all or any of the provisions of this Schedule is not necessary for protection of the workers in the factory, the Chief Inspector may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein.] SCHEDULE XXVII CARPET AND WOOLLEN DRUGGET MAKING OR ANY WORK INCIDENTAL THERETO OR CONNECTED THEREWITH 1. Definition. (a) "Efficient exhaust draught" means localized ventilation affected by mechanical means for the removal of gas, vapour, dust or fumes at the point where they originate so as to prevent them from escaping into the air of any place in which work is carried on. No draught shall be deemed efficient, which fails to remove smoke generated at the point where such gas, vapour, fume or dust originate. (b) "First employment" means first employment in any process mentioned under paragraph 2 and yarn dyeing process, and shall also include re-employment in the said process following any cessation of employment for a continuous period exceeding three calendar months. under an efficient exhaust draught or under such other conditions as may be approved 2. Exhaust draught. The following processes shall not be carried on except by the Chief Inspector : (a) Carding and spinning of raw fibre; (b) Weaving. 3. Prohibition relating to young persons- No young person shall be employed or permitted to work in any operations specified in Paragraph 2 (c) and 2 (d) or at any place where such operations are carried on. 22 4. Ventilation. Every workroom shall be provided with inlets and outlets of adequate size so as to secure and maintain efficient ventilation to all parts of the room. 5. Protective equipments and clothing.-(i) The occupier of the factory shall provide and maintain dust respirator for all persons employed in process included under paragraph 2. (ii) The occupier shall provide and maintain protective clothings, gloves for all persons employed in dyeing process. 6. Medical facilities and records of examinations and tests. (1) The occupier of every factory in which the carpet and woollen drugget manufacturing process is carried on shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein, whose employment shall be subjected to the approval of the Chief Inspector of Factories; and (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a). (2) The records of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 7. Medical examination by Certifying Surgeon. (i) Every worker employed in any of the processes specified in paragraph 2 and in yarn dyeing process shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include tests for detection of methaemoglobin in blood, or para nitro phenol in urine, test for central nervous system function, pulmonary function test and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (ii) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests for detection of methaemoglobin in blood, or para nitro phenol in urine, test for central nervous system function, pulmonary function test and chest X-ray once in every 3 years. (iii) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of examination and re-examination carried out shall be kept in the 22 Provisions of clause (3) of Article 348 of the Constitution, the Governor is pleased to order the publication of the following English translation of Notification no. 09/2024/2411/XXXVI-03-2024-1792147, dated December 23, 2024 custody of the Manager of the factory. The records of each examination carried under sub-paragraphs (i) and (ii), including the nature and results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (iv) The Certificate of Fitness and the Health Register shall be readily available for inspection by the Inspector. SCHEDULE XXVIII BRASSWARE MAKING OR ANY WORK INCIDENTAL THERETO OR CONNECTED THEREWITH 1. Definitions. (a) "Efficient exhaust draught" means localized ventilation affected by mechanical means for the removal of gas, vapour, dust or fumes at the point where they originated so as to prevent them from escaping into the air of any place in which work is carried on. No exhaust draught shall be deemed efficient. which fails to remove smoke generated at the point where such gas, vapour, fume or dust originate. (b) "First employment" means first employment in any process mentioned under paragraph 2 and shall also include re-employment in the said process following any cessation of employment for a continuous period exceeding three calendar months. (c) "Dressing or fettling operation" includes stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not include (a) the removal of metal from a casting when performed incidentally in connection with the renchining or assembling of castings after they have been dressed or fettled, or (b) any operation which is a knock-out operation within the meaning of this Schedule. (d) "knock-out operation" means all methods of removing castings from moulds and the following operations, when done in connection therewith, namely, stripping, coring-out and the removal of runners and risers. 2. Exhaust draught. (1) The following processes shall not be carried on except under an efficient exhaust draught or under such other conditions as may be approved by the Chief Inspector- (a) casting process; (b) buffing and polishing of brass articles; (c) electroplating of brass article using electrolyte; (d) degreasing and cleaning. (2) Such draught shall be provided by mechanical means and shall operate on dust, vapour or spray given off in the process as nearby as may be at the point of origin. The exhaust draught shall be so constructed, arranged and maintained as to prevent the dust, vapour or spray entering into any workroom or place in which work is carried on. 3. Prohibition relating to young persons- No young person shall be employed or permitted to work in any operations specified in Paragraph 2 (c) and 2 (d) or at any place where such operations are carried on. 23 4. Arrangement and storage. For the purposes of promoting safety and cleanliness in workrooms the following requirements shall be observed :- 23 Provisions of clause (3) of Article 348 of the Constitution, the Governor is pleased to order the publication of the following English translation of Notification no. 09/2024/2411/XXXVI-03-2024-1792147, dated December 23, 2024: (4) Moulding boxes, loam plates, ladles patterns, pattern plates, frames, boards, box weights and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; (b) suitable and conveniently accessible racks, bins or other receptacles shall be provided and used for the storage of other gear and tolls; (c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. 5. Cleanliness of Indoor Workplaces (1) All accessible parts of the walls of every indoor workplace in which the casting processes are carried on and of everything not less than 4.2 metres from the floor at least once in every period of fourteen months. affixed to those walls shall be effectively cleaned by a suitable method to a height of A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date, shall be maintained. (2) Effective cleaning by a suitable method shall be carried out at least once every working day, of all accessible parts of the floor of every indoor workplace in which the processes are carried on, other than parts which are of sand; and the parts which are of sand shall be kept in good order. 6. Manual operations involving molten metal. (1) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation- (a) which is adequate for the safe performance of the work; and (b) which, so far as reasonably practicable, is kept free from obstruction. (2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which, where any person walks while engaged in the operation, shall be on the same level: Provided that, where necessary to enable the operation to be performed without undue risk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 7. Dust and Fumes. (1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. (2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. (3) Mould stoves, core stoves and annealing furnaces shall be so designed, constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. (4) All knock-out operations shall be carried out- (a) in a separate part of the foundry suitably partitioned off, being a room or part in which so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard of general ventilation are provided; or (b) in an area of foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. (5) All dressing or fettling operations shall be carried out- (a) in a separate room or in a separate part of the foundry suitably partitioned off; or (b) in an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 8. Disposal of dross and skimmings. Dross and skimmings removed from the molten metal or taken from a furnace shall be placed forthwith in a suitable receptacle. 9. Floor or workroom. (1) The floor of every room in which the processes specified in paragraphs 2(i)(c) and 2(i)(d) are carried on shall be :- (a) of cement or similar material so as to be smooth and impervious to water; (b) maintained in sound condition; and (c) the floor shall be cleaned daily. (2) Floors of indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have an even surface of hard material (3) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. (4) All parts of the surface of the floor of any such indoor workplace are of sand shall, so far as practicable, be maintained in an even and firm condition. 10. Ventilation. Every workroom shall be provided with inlets and outlets of adequate size, so as to secure and maintain efficient ventilation to all parts of the room. 11. Protective clothing and protective equipment. (1) The occupier of the factory shall provide and maintain the following protective clothing for use of workers who may come in contact with liquid, employed in process specified in paragraph 2(i)(c)- (a) waterpoof apron and bib; and (b) loose rubber gloves and rubber boots or any other waterproof boots. (2) The occupier of the factory shall provide and maintain adequate arrangements and place for keeping and drying the protective clothing for the use of workers ployed in the factory. (3) The occupier of the factory shall provide and maintain suitable respirator for all workers employed in processes specified in paragraphs 2(i)(a) and 2(i)(b). 12. Medical facilities and records of examination and tests. (1) The occupier of every factory in which processes specified in paragraph 2 are carried on shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein, whose employment shall be subjected to the approval of the Chief Inspector of Factories; (b) provide to said medical practitioner all the necessary facilities for the purpose referred to in clause (a); and (c) provide and maintain a sufficient supply of suitable ointment and impermeable waterproof plaster in a separate box readily accessible to the workers and used solely for the purpose of keeping the ointment and the plaster. (2) The records of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. (3) The medical practitioner shall examine all workers specified in paragraph 2(i)(c) before they are employed in electroplating process. Such examination shall include inspection of hands, forearms and nose. (4) The records of examination referred to in sub-paragraph (3) shall be shaintained in a separate register, approved by the Chief Inspector of Factories, which shall be kept readily available for inspection by the Inspector. 13. Medical Examination by Certifying Surgeon_ (1) Every worker employed in any of the processes specified in paragraph 2, shall be examined by a Certifying Surgeon within 15 days of his first employment, such examination shall include test for chromium, nickel or cadmium in urine, pulmonary function test and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include test for chromium, nickel or cadmium in urine, pulmonary function test and chest X-ray once in every 3 years. (3) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of examination and re-examinations carried out shall be kept in the custody of the Manager of the factory. The records of each examination carried out under sub-paragraphs (1) and (2), including the nature and results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be readily available for inspection by the Inspector. 14. Mess-room. There shall be provided and maintained for the use of all workers employed in the processes specified in paragraph 2 and remaining on the premises during the meal intervals, suitable mess-room, which shall be furnished with sufficient tables and benches under supervision of a responsible person. 15. Washing facilities. (1) There shall be provided and maintained in a clean state and in good repair for the use of all persons employed in the processes specified in paragraph 2:- (a) a wash place under cover with either :- (i) a trough trough v with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 cms for every five such persons employed at any time, and having a constant supply of water from taps or jets above trough at intervals of not more than 60 cms; or (ii) at least one washbasin for every five such persons employed at any one time fitted with a waste pipe and plug and having a constant supply of water laid on; and ( b) a sufficient supply of clean towels made of suitable materials renewed daily with supply of soap or other suitable cleansing material and of nail brushes. 16. Food, drink, etc. prohibited in workroom. No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any room in which the processes specified in paragraph 2 are carried on. SCHEDUKLE XXIX LOCK AND HARDWARE MAKING OR ANY OTHER WORK INCIDENTAL THERETO OR CONNECTED THEREWITH 1. Definitions. (a) "Efficient exhaust draught" means localized ventilation affected by mechanical means for the removal of gas, vapour, dust or fumes at the point where they originate so as to prevent them from escaping into the air of any place in which work is carried on. No exhaust draught shall be deemed efficient, which fails to remove smoke generated at the point where such gas, vapour, fume or dust originate; (b) "First employment" means first employment in any process mentioned under paragraph 2 and shall also include re-employment in the said process following any cessation of employment for a continuous period exceeding three calendar months; (c) "dressing or fettling operation" include stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not include (a) the removal of metal from a casting when performed incidentally in connection with the machining or assembling of castings after they have been dressed or fettled, or (b) any operation which is a knock-out operation within the meaning of this Schedule; (d) "knock-out operations" means all methods of removing castings from moulds and the following operations, when done in connection therewith, namely, stripping, carrying out and the removal of runners and risers. 2. Exhaust draught.-(1) The following processes shall not be carried on except under an efficient exhaust draught or under such other conditions as may be approved by the Chief Inspector: (a) casting the metal parts; (b) metal finishing operations involving buffing and polishing; (c) all such processes in which electroplating is carried on by using electrolyte; (d) spray painting. (2) Such draught shall be provided by mechanical means and shall operate on dust, vapour or spray given off in the process as nearby as may be at the point of origin. The exhaust draught shall be so constructed, arranged and maintained as to prevent the dust, vapour or spray entering into any workroom or place in which work is carried on. 3. Prohibition relating to young persons- No young person shall be employed or permitted e in any of the operations specified in Paragraph 2(c) and 2(d) or at any place where such operations are carried on. 24 4. Arrangement and storage. For the purposes of promoting safety and cleanliness in workrooms the following requirements shall be observed : (a) moulding boxes, loam plates, ladles patterns, pattern plates, frames, boards, box weights and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; (b) suitable and conveniently accessible racks, bins or other receptacles shall be provided and used for the storage of other gear and tools; (c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. 24 Provisions of clause (3) of Article 348 of the Constitution, the Governor is pleased to order the publication of the following English translation of Notification no. 09/2024/2411/XXXVI-03-2024-1792147, dated December 23, 2024 5. Cleanliness of indoor workplaces. (1) All accessible parts of the walls of every indoor workplace in which the casting processes are carried on and of everything affixed to those walls shall be effectively cleaned by a suitable method to a height of not less than 4.2 metres from the floor at least once in every period of fourteen months. A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date shall be maintained. (2) Effective cleaning by a suitable method shall be carried out at least once every working day of all accessible parts of the floor of every indoor workplace in which the processes are carried on, other than parts which are of sand, and the parts which are of sand shall be kept in good order. (3) Floors of indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have an even surface of hard material. (4) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. (5) All parts of the surface of the floor of any such indoor workplace are of sand shall, so far as practicable, be maintained in an even and firm condition. 6. Manual operations involving molten metal. (1) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation: (a) which is adequate for the safe performance of the work; and (b) which, so far as reasonably practicable, is kept free from obstruction. (2) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor, all parts of which where any person walks while engaged in the operation, shall be on the same level: Provided that, where necessary to enable the operation to be performed without undue risk, nothing in the paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 7. Dust and Fumes. (1) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. (2) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. (3) Mould stoves, core stoves and annealing furnaces shall be so designed, constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. (4) All knock-out operations shall be carried out- (a) in a separate part of the foundry suitably partitioned off, being a room or part in which so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard of general ventilation are provided; or (b) in area of the foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. (5) All dressing or fettling operations shall be carried out- (a) in a separate room or in a separate part of the foundry suitably partitioned off; or (b) in an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 8. Disposal of dross and skimmings. Dross and skimmings removed from the molten metal or taken from a furnace shall be placed forthwith in a suitable receptacle. 9. Floor of workroom. (1) The floor of every room in which the processes specified in paragraph 2(1)(c) are carried on shall be- (a) of cement or similar material so as to be smooth and impervious to water; (b) maintained in sound condition. (2) The floor shall be cleaned daily in processes specified in paragraph 2. (3) Floors of indoor workplaces in which the casting processes are carried on, other than parts which are of sand, shall have an even surface of hard material. (4) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. (5) All parts of the surface of the floor of any such indoor workplace are of sand shall, so far as practicable, be maintained in an even and firm condition. 10. Ventilation. Every workroom shall be provided with inlets and outlets of adequate size, so as to secure and maintain efficient ventilation to all parts of the room. 11. Protective clothing and protective equipment. (1) The occupier of the factory shall provide and maintain the following protective clothing for use of workers who may come in contact with liquid, employed in process specified in paragraph 2(1)(c): (a) waterproof apron and bib; and (b) loose rubber gloves and rubber boots or any other waterproof boots. (2) The occupier of the factory shall provide and maintain adequate arrangements and place for keeping and drying the protective clothing for the use of workers employed in the factory. (3) The occupier of the factory shall provide and maintain suitable respirator for all workers employed in processes specified in paragraphs 2(1)(a) and 2(1)(b). 12. Medical facilities and records of examination. (1) The occupier of every factory in which processes specified in paragraph 2 are carried on shall- (a) employ a qualified medical practitioner for medical surveillance of the workers employed therein, whose employment shall be subjected to the approval of the Chief Inspector of Factories; (b) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (a); and (c) provide and maintain a sufficient supply of suitable ointment and impermeable waterproof plaster in a separate box readily accessible to the workers and used solely for the purpose of keeping the ointment and the plaster. (2) The records of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Chief Inspector of Factories which shall be kept readily available for inspection by the Inspector. (3) The medical practitioner shall examine all workers specified in paragraph 2(1)(c) before they are employed in electroplating process. Such examination shall include inspection of hands, forearms and nose. 13. Medical examination by Certifying Surgeon.-(1) Every worker employed in any of the processes specified in paragraph 2, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include test for chromium, cadmium or nickel in urine, pulmonary function test and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (2) Every worker employed in the said process shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include test for chromium. cadmium or nickel in urine, pulmonary function test and chest X-ray once in every 3 years. (3) The Certifying Surgeon, after examining a worker, shall issue a Certificate of Fitness in Form 26. The record of examination and re-examinations carried out shall be kept in the custody of the Manager of the factory. The records of each examination carried out under sub-paragraphs (i) and (ii), including the nature and results of the tests, shall also be entered by the Certifying Surgeon in a Health Register in Form 27. (4) The Certificate of Fitness and the Health Register shall be readily available for inspection by the Inspector. 14. Mess-room. There shall be provided and maintained for the use of all workers employed in the processes specified in paragraph 2 and remaining on the premises during the meal intervals, a suitable mess-room, which shall be furnished with sufficient tables and benches under supervision of a responsible person. 15. Washing facilities. There shall be provided and maintained in a clean state and in good repair for the use of all persons employed in the processes specified in paragraph 2: (a) a wash place under cover with either- (i) a trough with a smooth impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 cms for every five such persons employed at any time, and having a constant supply of water from taps or jets above trough at intervals of not more than 60 cms; or (ii) at least one washbasin for every five such persons employed at any one time fitted with a waste pipe and plug and having a constant supply of water laid on; and (b) a sufficient supply of clean towels made of suitable materials renewed daily with supply of soap or other suitable cleansing materials and of nail brushes. 16. Food, drink etc. prohibited in workroom. No food, drink, pan and supari or tobacco shall be consumed or brought by any worker into any room in which the processes specified in paragraph 2 are carried on. FORM No. 1 NAME OF FACTORY [Rule 3(1)] Particulars of rooms in the factory Name of room in factor y Dimensions in feet Total area in squar e feet Floor area occupied by machiner y in the room Breathin g space (content s in cubic feet). Total volum e of air in the room Lengt h Breadt h Height Maximu m Minimu m Averag e 1 2 3 4 5 6 7 8 9 10 Numbe r and size of doors Ventilation Maximu m capacity of the room Maximu m number of persons intended to be employe d in the rooms Whethe r the room is to be used as a work- room of for storage only Date of constructio n Remark s Number and size of window s opening s Numbe r and size of skylight opening s Total area in squar e feet 11 12 13 14 15 16 17 18 19 Signature of the Occupier...................... Signature of the Manager....................... Questionnaire Annexed to Form No. 1 [Rule 3(1)] Careful attention to the questionnaire will assist in drawing up the plans in accordance with the law, and thus prevent delay in dealing with the plans. Plans— (a) Has a site-plan showing the immediate surroundings including adjacent buildings and other structures, roads, drains, etc., been submitted in triplicate. (b) If there is a system of underground sewage within 100 ft. of the factory, has its position been shown in the site plan ? (c) Have the direction i.e., north, south, east and west been shown on the site- plans as well as on the detailed plans ? (d) Have the municipal nos. or the field nos. of the premises and the surrounding areas been shown on the site-plan ? (e) Have the factory premises been clearly demarcated in the site-plan in distinctive colour ? (f) Have the detailed plans of the factory indicating all relevant details " relating to doors, windows, ventilators, fire escapes, etc., been submitted in triplicate ? (g) Are all new buildings, parts of buildings (if extensions) or alterations in existing buildings shown by boundaries duly marked in a distinctive colour ? (h) Are all rooms, sheds, enclosures, etc., serially numbered inside a circle on the plans, corresponding to the serial entry in Form No. 1 ? (i) Are the outlines of all rooms, sheds, enclosures, etc., shown in the site-plan and allotted the same number as in Item 1(h) above? (j) Is the sectional elevation of such room or shed, etc., shown separately ? (k) Is the minimum and 'maximum height of every room, shed, etc., shown clearly in the sectional elevation ? (l) Is the material of which the roof is constructed indicated the sectional elevation ? (m) Are the heights of all the workrooms in accordance with the provisions of Rule 4 as under : (i) Is the minimum height 20 ft. with C. I. sheet roofing ? (ii) Is the minimum height 14 ft. with A. C. sheet roofing or R.B./R. C. C. roofing ? (iii) Has an inner ceiling of a heat resisting material with an air gap of at least 4" been provided at a minimum height of 14 ft. and the name of the heat resisting material given? (iv) Has an exemption been sought for a height of up to 12 ft. R.B/R. G. C. roofing ? (v) Has an exemption been sought for on the assurance of not employing more than 50 workers in the factory on any day ? (n) Is the minimum distance of the nearest building from latrines and urinals shown on the plans ? (o) Is the minimum distance of the nearest well, hand-pump or other drinking water centres shown in the drawing ? (p) Are water centres shown on the plans ? (q) Are the sizes of all the doors and ventilators shown on the plans alongwith their exact position ? (r) Are all the drains, pipes and sewers for carrying sullage sewage water effluent and waste products running within the factory premises constructed and shown in the plans ? (s) Are the positions of various machines fitted or proposed to be fitted shown in the drawings together with their names ? 2. Form No. 1 (a) Is Form No. 1 submitted in triplicate, filled in for all workrooms, godowns, etc. which are proposed to be constructed or extended ? (b) Have the internal dimensions only been entered in all the columns of Form No. 1 ? (c) Is the breathing space of workroom, shed, etc., calculated as shown below: Floor area of room x its mean height (height above 14 ft. has to be left out of calculation). (d) Is the maximum capacity entered in Column No. 15 of Form No. 1 the maximum number of persons shown as the lower value of the two calculations shown below : (i) Floor area of a room less area occupied by machinery in the room divided by 36 [Rule 4(ii)]. (ii) Breathing space [as in (c) above] divided by 500. (e) Have the maximum number of persons as worked out above (lower value) been also shown on the plans for each workroom corresponding to Column No. 15 of Form No. 17 ? (f) Is the window, ventilator and skylight area provided at the minimum rate of 1 sq. ft. to every 15 sq. ft. of floor area of the room ? (Rule 19) ? (g) Can the windows and skylights under Columns Nos. 12 and 13 of Form No. 1 all be opened for ventilation ? It is recommended that window and skylights may be provided one opposite to another so as to provide cross ventilation. (h) Has a flow chart of the manufacturing process supplemented by its brief description in various stages been submitted in triplicate ? Rule 3(1) (a) 3. Doors and ventilators.—(a) Is every work room provided with at-least two doors or exits ? (b) Is the minimum size of every door or exit 6'-6"x3' Rule 61. (c) Have any doors of ventilators in common with two adjacent rooms been counted in both ? (d) Are all the doors opening outwards ? (e) Do the windows and skylights entered under Cols. 12 and 13 of Form No. 1 actually serve the purpose of ventilation ? 4. Fire Escapes.—(In case of buildings of more than one storey, Rule 61) : (a) Are two fire escapes provided on either side of building ? (b) Are the fire escapes accessible from every room in the upper floor in the buildings ? (c) Is the material used in construction of the fire escapes non-combustible ? (d) Are the windows, doors giving access to and external stair-case arranged to open immediately from inside. (e) Is any fire escape or stair-way constructed at an angle greater than "450 ft. with the horizontal ? (f) Is any fire escape or stair way less than 45'Un width ? (g) Is any part of the factory building further (along the line of travel) than 150 ft. from the fire escape stair ? (h) Have the particulars given against Items 4(e), (f) and (g) above been also clearly shown in the various drawings being submitted ? 5. Latrines and urinals.—(a) Are the latrines and urinals provided separately for men and women ? (b) Are these sufficient to meet the requirements of Section 19, read with Rules 41 and 45 ? (c) Is the surrounding ground up to a distance of 4 ft. all round of impermeable material ? (d) Is the surrounding ground raised to at least 6" above the ground level ? (e) Is any latrines, ventilator or opening in the proximity of any opening of main building ? (f) Do any latrines or urinals communicate with any work room without any intervening space open to the sky ? (g) Are the latrines of the flush type ? (h) Are all the drains, pipes and sewers for carrying sullage, sewage water effluent and waste products running within the factory premises constructed of impermeable material ? (i) Are the drains of flush type latrines connected to drainge system of the local Boards ? (j) Is an efficient system of septic tanks provided if no drainage system exists ? (k) Are the latrines provided with roofing ? 6. Drinking water.—(a) Is the drinking water provided from a source provided by local Board. (b) Is any well constructed in the premises of the factory for drinking water or humidification purposes ? (c) Is the cylinder of the well pucca and impervious to water throughout and up to a depth not less than the lowest level of sub-soil water ? (d) Are the positions of water centres including wells, hand pumps situated at least 20 ft. away from the washing place, latrines and urinals ? 7. Rest shelter, canteen and creches.—If the plans relate to any of these, the following questions should also be answered— (i) Rest shelter: (a) Does the building fully meet the requirements of Rule 69(a) ? (b) Is the roof ef heat-resisting material ? (c) Is the height of every room in the rest shelter at least 12 ft. from the floor level to the lowest part of roof ? (ii) Canteen: (a) Does the building fully meet the requirements of— Rule 68(4), Rule 68(5), Rule 68(6), Rule 68(7). (b) Are the canteen buildings situated not less than 50 yards from any latrines, urinals, boiler house, coals, stack coals dumps etc.? (c) What is the minimum height of the buildings of canteen measured from the floor level to the lowest part of the roof ? (iii) Creche : (a) Does the building of creche meet fully the requirements of— Rule 70(2)(a), Rule 70(2)(b), Rule 70(2)(d), Rule 70 (2)(g). (b) Is the height of buildings not less than 12 ft. from floor level to the lowest part of roof ? We certify that the replies given to questionnaire above are correct. Signature of Manager. Signature of Occupier. N. B.—(i) After showing the above details, the plans and site-plan this questionnaire and Form No. 1 should all be submitted in triplicate to the Inspector of Factories of the Region concerned for the approval of the Chief Inspector of Factories, Uttar Pradesh. (ii) A certificate of stability signed by a person having the qualifications laid down in Rule 3(4) shall be submitted on Form No. 2 before the manufacturing process with the aid of power is begun in the building. FORM NO. 2 [Rules 3(3)] Certificate of Stability of a Factory or Part of a Factory (To be submitted after completion and before working) I hereby declare that I have personally examined the plans and specifications of the building described below, the actual materials and methods used in its construction and the finished building and am satisfied that its construction is such that its stability will be satisfactory when used as factory or part of a factory for the purposes herein declared. Description of Building 1. Name of the factory 2. Name of builder (s) or contractor (s) 3. General type of construction (a) Full name of signatory (in block letters) (b) Qualifications (c) Present occupation (d) Permanent postal address Purpose for which the building is to be used 5. Name of room or building for which this certificate is granted giving reference to plan no. 6. Nature of work to be carried on in the above room/building. 7. Nature and amount of moving power 8. Signature 9. Date 10. Signature of occupier with an endorsement that the Certifying Engineer inspected the factory at his request and certified its stability. NOTE.—The person giving the certificate must be: (a) a Corporate Member of the Institution of Civil Engineers, or (b) a Corporate Member of the Institution of Structural Engineers or (c) a Fellow Associate or Licentiate of the Royal Institute of British Architects, or (d) be a graduate in Civil Engineering and be also a Corporate Member of the Institute of Engineers (India), provided that no person, except in the case of buildings occupied or erected by any Government where a certificate may be granted by an officer not below the rank of an Executive Engineer, shall be authorized to sign a certificate of stability if he is in the full time employment of the owner or the builder of the building. FORM NO. 3 [Rule 7(1)] Registration and licence to work factory Registration No. Serial M. Fee Rs. Licence is hereby granted to valid only for the premises described below for use of a factory employing not more than___________________________________________ persons on any one day during the year and using motive power not exceeding ________________ h.p., subject to the provisions of the Factories Act, 1948 and the rules made thereunder. This licence shall remain in force till unless further renewed. The------------------------------19 Chief Inspector of Factories. Description of the Licensed Premises The licensed premises shown on the plan no________________________, dated_____________, are situated in______________________________and consist of Date of renewal Date of expiry Signature of licensing authority 1 2 3 FORM NO. 4 (Rule 14) Notice of occupation for Registration and grant or Renewal of Licence Written notice prescribed under Sections 6 and 7(i) of the Factories Act, 1948. (1) Full name of the factory and its licence number, if already registered _______________________ (2) (a) Postal address and situation of the factory including police station, tahsil and district _______________________ (4) Address to which communication relating to the factory should be sent _______________________ (3) Nature of manufacturing process/processes _______________________ (a) carried on in the factory during the last twelve months (in the case of factories already in existence) _______________________ (b) to be carried on in the factory during the next twelve months (in case of all factories). — _______________________ (4) Names and values of the principal products manufactured during the last twelve months _______________________ (5) (a) Maximum number of workers proposed to be employed on any one day during the year. _______________________ (b) Maximum number of workers employed in any one day during the last twelve months _______________________ (c) Number of workers to be employed in the factory _______________________ (6) (a) Nature and total amount of power (H. P.) installed or proposed to be installed _______________________ (b) Maximum amount of power (H. P.) proposed to be used _______________________ (7) In the case of a factory constructed or extended after the date of the commencement of the rule— (i) Reference number and date of approval of the plans for site, whether for old or new building and for construction or extension of factory, by the State Government/Chief Inspector _______________________ (ii) Reference number and date of approval of the arrangements, if any, made for the disposal of Irade waste and effluents and the name of the authority granting such approval _______________________ (8) Full name, father's name and residential address of: - _______________________ (i) the person who shall be Manager of the factory for the purposes of the Act _______________________ (ii) the occupier of the factory—(a) the Proprietor of the factory if it is a private firm or proprietory concern— _______________________ (b) the Directors of the factory if it is a limited company or firm — _______________________ (c) where Managing Agents have been appointed, the name of Managing Agents and their Directors — _______________________ (d) share-holders in case of a private company where no Managing Agents have been appointed _______________________ (e) the Chief Administrative Head of the factory if it is owned by Government or a public authority _______________________ (9) If the factory is covered by the provisions of Section 93 of the Factories Act (Act LXIII of 1948), full name, father's name, and address of the owner of the premises or buildings in which the factory is situated _______________________ (10) Date on which the Manager assumed charge _______________________ (11) Date on which the occupier occupied the premises or will occupy the premises _______________________ (12) Amount of fee Rs.) (Rs. paid in Treasury on vide chalan no. (enclosed) _______________________ Full signature of occupier_______________________ Full signature of Manager_______________________ Full signature of owner, if any_______________________ Date------------------ FORM NO. 4-A Notice of change of Manager [Rule 14-D] 1. Name of factory with current licence number ................................. 2. Postal address of the factory................................................. 3. Name of outgoing manager.................................................. 4. Name of the new manager with his postal residential address and telephone number, if any............................................................ 5. Date from which new manager took over charge.............................. Date........................... Place.......................... Signature of new Manager................................... Signature of Occupier......................................... FORM NO. 5 [Rule 16 (2)] Certificate Serial no................... Date......................... Serial no................... Date......................... I here by certify that I have personally examined (name)............................................. ........................................................... son/daughter of................................................ residing at........................................................ 66Who is desirous of being employed in a factory, and that his/her date of birth, (if available), is ......................................and the age as I hereby certify that I have.................... ...................................................... son/daughter of................................................ residing at........................................................ Who is desirous of being employed in a factory, and that his/her date of birth, (if available), is ......................................and the age as nearly as can be ascertained from any nearly as can be ascertained from any examination is.....................years, and that he/she is fit in accordance with the minimum physical standards prescribed, for employment in factory as an adult/child. His/Her descriptive marks are....................................................... examination is.....................years, and that he/she is fit in accordance with the minimum physical standards prescribed, for employment in factory as an adult/child. His/Her descriptive marks are...................................................... 2. Reason for— (i) Refusal of certificate. (ii) Certificate being revoked. Thumb-impression............................... Signature of Certifying Surgeon. Left thumb-impression of Examinee. Signature of Certifying Surgeon. I—Age— (i) A child must be over 14 years of age. (ii) An adolescent must be over 15 years and below 18 years. II—Eye-sight. III—General Health— (a) Hearing in each ear is good and that a candidate has no mental infirmity. (b) His/Her limbs, hands and feet are well formed and developed and that there is free and perfect normal motion of his/her joints : (c) His/Her chest is well formed and that his/her heart and lungs are sound. (d) There is no evidence of any abdominal disease and that he/she does not suffer from any inveterate skin disease. (e) The candidate does not bear any traces of acute or chronic disease pointing to an impaired constitution. (f) He/She bears marks of vaccination. (g) He/She has a proper degree of intelligence. (2) Those suffering from curable diseases should be rejected until cured. (3) Special attention should be paid to the presence of obvious signs of mal- nutrition and under development. FORM NO. 6 (Rules 22 and 81) Names and designations of persons, buildings, or parts of building and departments exempted Section or rule from which exemption is given Extent of and conditions of exemptions Date and number of order 1 2 3 4 FORM NO. 7 (Rule 24) Humidity Register Name of factory ................................................ and address..................................... Department............................................... Hygrometer Position............................... Year Hygrometer readings daily 66Approved hydrometers readings 1st, 2nd, 3rd and 4th Wednesday in each month Months Date First readings between Second reading between Third reading between 4 First reading Second reading Third reading Signat ure of per 7 a.m. and 9 a.m. 11 a.m. and 2 p.m. p.m. and 5-30 p.m. son who took the reading Dry bulb Wet bulb Dry bulb Wet bulb Dry bulb Wet bulb Dry bulb Wet bulb FORM NO. 8 (Rule 48) Lime washing, etc. Part of factory, e.g. name of room Parts limewashed, painted or varnished e.g. walls, ceiling, wood works, etc. Treatment (whether lime washed, painted or varnished) Date on which lime washing, painting or varnishing was carried out according to the English calendar Signature of occupier manager Remarks Day Month Year 1 2 3 4 5 6 7 8 [FORM NO. 9 (Prescribed under Rule 56) Report of Examination or test of Pressure Vessel or Plant 1. Name of occupier (or Factory) 2. Situation and address of factory 3. Name, description and distinctive number of pressure vessel or plant 4. Name and address of manufacturer and reference to their test certificate of certificates of competent person 5. Nature of process in which pressure vessel or plant is used 6. Particulars of pressure vessel or plant- (a) Date of construction (b) Thickness of walls (c) Date in which the pressure vessel or plant was first taken into use (d) Maximum permissible working pressure recommended by the manufacturer (e) Design pressure, if known (f) The history should be briefly given and the examiner should state whether he has seen the last previous report. 7. Date of last hydrostatic test, if any, and pressure applied 8. Is the pressure vessel or plant in open or otherwise exposed to weather or the damp? 9. What parts (if any) were inaccessible? 10. What examination and tests were made? Specify pressure if hydrostatic test was carried out............................... 11. Condition of pressure vessel or plant External (state any defects materially affecting the maximum permissible working pressure of the safe working of the pressure vessel or plant).................................. Internal 12. Are the required fittings and appliances provided in accordance with the rule................................ 13. Are all fittings and appliances properly maintained and in good condition? Have the pressure settings been checked and corrected? 14. Repairs (if any) required, and period within which they should be executed and any other condition which the person making the examination thinks it necessary to specify for securing safe workings.......................... 15. Maximum permissible working pressure, calculated from dimensions and from the thickness, and other data ascertained by the present examination, due allowance being made for conditions of working if unusual or exceptionally severe (State minimum thickness of walls measured during the examination)........................ 16. Where repairs affecting the maximum working pressure are required, state the working pressure— (a) Before the expiration of the period specified in item 14. (b) After the expiration of such period if the required repairs have not been completed. (c) After the completion of the required repairs................................ 17. Other observations....................................................... I certify that on......................................the pressure vessel or plant described above was thoroughly cleaned and (so far as its construction permits) made accessible for thorough examination and for such tests as were necessary for thorough examination and that on the said date, I thoroughly examined this pressure vessel or plant including its fittings and that the above is a true report of my examination. Signature.............................. Qualification........................ Address................................. Dale..................................... If employed by a Company or Association give name and Address.] FORM NO. 10 (Rule 76) Overtime muster-roll for persons on exempted work month ending Workers number in register Name Department Dates on which overtime has been Extent of overtime on each occasion Total overtime worked in hours Normal hours worked during the worked Time from Time to period 1 2 3 4 5 6 7 8 Normal rate of pay Overtime rate of pay Cash equivalent to the advantage accruing through the concessional sale of foodgrains and other articles Overtime earnings Reasons for overtime quoting section or rule 9 10 11 12 13 FORM NO. 11 [Rules 77 and 99] Notice prescribed under Sections 61 and 72, Factories Act, 1948 Date of enforcement..................... Name of factory under which it is registered/proposed to be registered.................place................district..... Group Nature of work of each group Number of workers employed in each group Relay or set of workers Shift or period of work Permanent Temporary 1 2 3 4 5 6 Number of hours of employment per day of...........all workers for each relay Monday Tuesday Wednesday Thursday Friday Saturday Sunday Me n Wo me n Chil d ren Me n Wo me n Chil d ren Me n Wo me n Chil d ren Me n Wo me n Chil d ren Me n Wo me n Chil d ren Me n Wo me n Chil d ren Me n Wo me n Chil d ren 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 FORM No. 11-(contd.) (Hours (time) of beginning and ending work for each relay, group and intervals of rest fixed under Section 55. Worker Group Name of work of each group Relay or set of workers Shift or period of work Work commences Rest interval or intervals Mondays to Fridays Saturdays Sundays 1 2 3 4 5 6 7 8 Men Women Boy Girls Work ends From To From To From To Mondays to Fridays Saturdays Sundays 9 10 11 12 13 14 15 16 17 Charts showing the relation of relays working on continuous processes similar to those suggested in Chief Inspector of Factories Office Circular No. 2404, dated March 26, 1949 First week Second week Third week Mon. Tue. Wed. Thu. Fri. Sat. Sun. Shift Relay Mon. Tue. Wed. Thu. Fri. Sat. Sun. Mon. Tue. Wed. Thu. Fri. Sat. Sun. Factory Manager's Signature............. Instructions to be followed while filling in the notice of periods of work 1. Divide all the workers into groups according to their nature of work. Show the number of workers working in each group [Section 61(4)]. 2. Use numericals (1, 2, 3 and 4, etc.) for groups. 3. Show the nature of work against each group. 4. Make relays of groups according to Section 2(r) and specify them as I, II, III, etc. 5. Show the daily working hours exclusive of periods of the fixed rest interval of each relay or set of workers in the upper half of the notice. 6. Use letters, A, B, C, etc. for shifts and periods of work. 7. Do not arrange the shift in such a way that more than one relay of workers is engaged in work of the same kind at the same time as overlapping shifts are prohibited (Section 58). 8. Arrange the periods of work for adult workers (except of workers exempted from Sections 54 and 55) in such a way that no adult worker is required to work for more than 9 hours in any day (Section 54) and that no worker shall work more than 5 hours before he has had an interval of rest for at least half an hour (Section 55). 9. Arrange the working hours in such a way that weekly hours of the adult workers (except those who are exempted from the provisions of Section 51) do not exceed 48 hours a week (Section 51). 10. Arrange the periods of work of adult workers (except those exempted from Section 56) in such a way that inclusive of rest interval they shall not spread over more than 10-1/2 hours (Section 56). 11. Fix the periods of work for clerical staff working in the precincts of the factory as they come under the definition of "worker" as defined under Section 2(1) of the Factories Act, 1948. 12. Arrange, the periods of work for child workers in accordance with the provisions of Chapter VII. 13. Show the weekly holiday for each relay or set of workers in the foot-note of each notice. 14. Submit the notice of periods for work in duplicate to the Inspector of Factories of the Region concerned before the day it is enforced. If there is any change in the system of work a revised notice of periods for work shall be submitted [Section 61(10)]. Special instructions for filling in the chart which is to be used only in cases of relays working on continuous process or of sets of workers working in successive periods. I. Fill in the chart with the help of Chief Inspector of Factories' Circular No. 2402- F, dated March 26, 1949. II. Show the periods of work Inclusive of rest intervals of adult workers on continuous processes in the upper half of the notice. FORM No. 12 (Rule 78) Register of Adult Workers as prescribed under Section 62 of the Act FORM No. 13 (Rule 100) Register of Child Workers as prescribed under Section 73 of the Act FORM No. 14 (Rule 102) Serial No..................................... Department.................................. Serial no. in the Register of Adult/Child workers................... Date of entry into service................. Adult/Child Name............................ Father's name.................. Date and amount of payment made in lieu of leave due................ LEAVE WITH WAGES REGISTER NAME OF FACTORY................ 1 Calendar year service 2 Wage paid from...................... to................. 3 Wages earned during the wage period 4 No. of days of work performed No. of days worked during the calendar year 5 No. of days of lay-off 6 No. of days of maternity leave 7 No. of days of leave enjoyed 8 Total of Columns 4 to 7 9 Balance of leave from preceding year Leave to credit 10 Leave earned during the year mentioned in Column 1 11 Total of Columns 9 and 10 12 Whether leave in accordance with scheme under Section 79(8) was refused 13 Leave enjoyed from................... to......................... 14 Balance of leave to credit 15 Normal rate of wages 16 Cash equivalent of advantage accruing through concessional sale of foodgrains and other particulars 17 Rate of wages for the leave period (Total of Columns 15 and 16) 18 Remarks FORM No. 15 (Rule 103) LEAVE BOOK Serial No..................................... Department.................................. Serial no. in the Register of Adult/Child workers................... Date of entry into service................. Adult/Child Name............................ Father's name.................. Date and amount of payment made in lieu of leave due................ NAME OF FACTORY...................... 1 Calendar year service 2 Wage paid from...................... to............................ 3 Wages earned during the wage period 4 No. of days of work performed No. of days worked during the calendar year 5 No. of days of lay-off 6 No. of days of maternity leave 7 No. of days of leave enjoyed 8 Total of Columns 4 to 7 9 Balance of leave from preceding year Leave to credit 10 Leave earned during the year mentioned in Column 1 11 Total of Columns 9 and 10 12 Whether leave in accordance with scheme under Section 79(8) was refused 13 Leave enjoyed from................... to......................... 14 Balance of leave to credit 15 Normal rate of wages 16 Cash equivalent of advantage accruing through concessional sale of foodgrains and other particulars 17 Rate of wages for the leave period (Total of Columns 15 and 16) 18 Remarks FORM No. 16 [Rule 107(2)] [I hereby require that in the event of my death before resuming work, that balance of my pay, due for the period of leave with wages not availed of shall be paid to.................... who is my.............. Witnesses: 1..................... ........................Signature of Worker. 2.....................Date. ........................Present Address Permanent Home Address FORM NO. 17 (Section 87, Rule 109) FACTORIES ACT, 1948 Health Register For use in pursuance of Special Rules in certain dangerous occupations Pages Part I—List of persons employed Part II—General result of examination See Instructions below THIS FORM OF HEALTH REGISTER IS APPROVED BY THE CHIEF INSPECTOR OF FACTORIES, U.P., FOR USE IN PURSUANCE OF THE SPECIAL RULES UNDER SECTION 87 OF THE FACTORIES ACT, 1948 Instructions Certifying Surgeon The health register is in two parts in each of which entries by the certifying surgeon are required at each visit. In Part I of the register the Certifying Surgeon should at the time of examination, enter the date at the head of one of the columns numbered 6 to 18 ; and in the space below opposite the name of each person examined on that date, a brief note of the condition found using signs in accordance with the scheme on footnote of the cover where lead is in question. In Part II of the register, the certifying surgeon should again enter (in Column 3) the date of examination with a statement of the total number examined on that occasion in Column 4 ; and (in Column 5) any certificate of suspension from work, or certificate permitting resumption of work, and particulars of any other directions given by him, appending his signature in Column 6. Occupier It is the duty of the occupier to enter in Part I, the following particulars with regards to each person to be examined. Name in full (Column 2). The process in which he or she is employed (Column 3). Age when first employed in that process (Column 4). Date of first employment in that process (Column 5). The particulars in Part I may be kept in the form of an approved card register; but such cards not supplied. The particulars in respect of each person so employed must be entered by the occupier immediately such person commences to work in the process named. The examination should be made at appointed times (arranged with the Certifying Surgeon), of which notice should be given to all workers concerned. In order to secure clue privacy it is requested that the Certifying Surge, may have the exclusive use of room or office while he is conducting examination. Work to which this register applies Name of occupier--------------------------- Address of factory--------------------------- Special rules to which the register refers----------------- Signature of Occupier or Manager------------ Date-------------------- PART I List of persons employed in process Particulars Number Worker's name in full Process First employed in such process Date result Date result Date result Date result Age Date 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 No. Reference to Part I Date of examination Number of persons Particulars of any direction by the Certifying Surgeon. Signature of certifying Page Column examined Any certificate of suspension or certificate permitting resumption of work must be entered here in full Surgeon 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART II Reference to Part I Date of Number Particulars of any Signature Page Column examination of persons examined directions given by the Certifying Surgeon. Any certificate of suspension or certificate permitting resumption of work must be entered here in full of Certifying Surgeon 1 2 3 4 5 6 Explanation of signs used by the Certifying Surgeon The figures (1, 2, 3, 4) relate to the state of health so as it may have been affected by employment in lead. They have the following meaning: (1) No comment. (2) Blue line, or indication thereof. (3) Anaemia, with blue line, or other signs of impairment of health suggestive of absorption of lead. (4) Suspension by reason of impairment of health from the effects of work in lead. The letters A, B, C relate to the state of health apart from any effect of work in lead. The letter A means "no comment"; B and C indicate degrees of impairment of general health ; D means suspension (for reasons other than impairment of health from the effects of work in lead); and X denotes carelessness, neglect of precaution or unsuitability for work in lead. [FORM 18 (Section 88, Rule 110) Notice of Accidents or Dangerous Occurrence, resulting in Death or Bodily Injury To, ................................................ ....................................................Dated......................................................................... Sir, I hereby give notice under Section 88 of the Factories Act, 1948 that fatal/non- fatal accident occurred in this factory to the person mentioned below :— 1. Name of occupier (of Factory)/Employer..................................... 2. Address of E.&.I. Employer's Code No...............................................premises where accident or dangerous occurrence took place.................... 3. Nature of Industry........................................................ 4. Branch or department and exact place where the accident or dangerous occurrence took place................. 5. Name and address of injured person....................................... 6. (a) Sex.................................................................. (b) Age (last birthday).................................................... (c) Occupation of the injured person....................................... 7. Local E.S.I. Office to which the injured person is attached..................... 8. Date, shift and hour of accident or dangerous occurrence....................... 9. (a) Hour at which the injured person started work on the day of accident or dangerous occurrence.............................................................. (b) Whether wages in full or part are payable to him for the day of the accident or dangerous occurrence.............................................................. 10. Cause or nature of accident or dangerous occurrence.......................... 11. Cause of accident or dangerous occurrence : (a) If caused by machinery................................................ (i) Give name of the machine and the part causing the accident or dangerous occurrence........................................................ (ii) State whether it was moved by mechanical power at that time.......... (b) State exactly what the injured person was doing at that time................ (c) In your opinion, was the injured person at the time of accident or dangerous occurrence........................................................... (i) acting in contravention of provisions of any law applicable to him, or (ii) acting in contravention of any orders given by or on behalf of his employer, or (iii) acting without instructions from his employer. (d) In case reply to (c), (i) (ii) or (iii) is in the affirmative state whether the act was done for the purpose of securing the safety in connection with the employer's trade or business. 12. In case the accident or dangerous occurrence happened while travelling in the employer's transport state whether................................................... (i) the injured person was travelling as a passenger to or from his place of work...... (ii) the injured person was travelling with the express or implied permission of his employer, (iii) the transport is being operated by or on behalf of the employer or some other person by whom it is provided in pursuance of arrangements made with the employer, and (iv) the vehicle being not/being operated in the ordinary course of public transport service. 13. In case the accident or dangerous occurrence happened while meeting emergency state............................................................................. (i) its nature................................................................ (ii) whether the injured person at the time of accident or dangerous occurrence was employed for the purpose of his employer's trade or business in or about the premises at which the accident or dangerous occurrence took place. 14. Describe briefly how the accident or dangerous occurrence occurred. 15. Name and addresses of witnesses : (1) (2) 16. (a) Nature and extent of injury (e.g. fatal, loss of finger, fracture of leg, sealed or scratch and followed by sepsis.) (b) Location of injury (right leg, left hand or left eye etc.) 17. (a) If the accident or dangerous occurrence is not fatal, state whether the injured person was disabled for more than, 48 hours. (b) Date and hour of return to work. 18. (a) Physician, dispensary or hospital from whom or in which the injured person received or is receiving treatment. (b) Name of dispensary/panel doctor selected by the injured person................. 19. (i) Has the injured person died............................................ (ii) If so, date of death........................................................ I certify that to the best of my knowledge and belief, the above particulars are correct in every respect. Signature ................................. Name and Designation of the Occupier or Manager-Employer.................................. Employer's Address and Code No........................................................ (This space is to be completed by the Inspector of Factories) Sex (Men, Women, Boy or Girl). District Date of receipt. Number of accident or dangerous occurrence. Causation number, other particulars (e.g. fatal leg injury, arm injury, etc.) Date of Investigation............................................................... Result of Investigation............................................................] [FORM NO. 18-A (Section 88, Rule 10) Notice of dangerous occurrence not resulting in death or bodily injury 1. Name and address of Factory................................................................................... 2. Name of the Occupier............................................................................................... 3. name of the Manager................................................................................................. 4. Name of Industry...................................................................................................... 5. Branch or Department and exact place where the dangerous occurrence took place............................................................................................................................. 6. Date and hour occurrence........................................................................................... 7. Nature of Dangerous Occurrence (state exactly what happened). I certify that, to the best of my knowledge and belief, above particulars are correct in every respect. Signature of the Occupier / Manager. Date of despatch of report. (This space to be completed by Inspector of Factories) District..................................................................... ...... D.O. No........................................................................ Causation No................................................................ Date of receipt................................................. . Date of investigation...................................... .... Result of investigation....................................................................................................] FORM NO. 19 (Section 89, Rule 112) Notice of certain diseases 1. Name of factory.................................................. 2. Address of factory.................................................. 3. Address of office or private residence of occupier.............................................. 4. Name of industry.................................................. 5. Name, father's name and factory ticket number of patient......................... 6. Address of patient.................................................. 7. Sex and age of patient.................................................. 8. Precise occupation of patient.................................................. 9. Nature of poisoning or disease from which patient is suffering and the approximate period of illness........................ 10. Has the case been reported to the Certifying Surgeon......................... 11. Have particulars of the case been entered in the Health Register.................... .............................................................................. Signature of Factory Manager......................... Date......................... to be filled in by the 73Inspector of factories No. of case......................... Remarks.............................. FORM NO. 20 (Section 108, Rule 118) Abstract of the Factories Act, 1948 and the U. P. Factories Rules, 1950 (To be fixed in a conspicuous and convenient place at or near the main entrance to the factory) INTERPRETATION "Factory" means any premises including the precincts thereof— (i) Whereon ten or more workers-are working or were working on any day of the preceding twelve months, and in any part of which a manufacturing process is being carried on with the aid of power, or is ordinarily so carried on ; or (ii) Whereon twenty or more workers are working, or were working on any day of the preceding twelve months, any in any part of which a manufacturing process is being carried on without the use of power, or is ordinarily so carried on, but does not include a mine subject to the operation of the Mines Act, 1952 (XXXV of 1952) of a railway running shed. "Worker" means a person employed, directly or through any agency, whether for wages or not, in any manufacturing process or in cleaning any part of the machinery or premises used for a manufacturing process, or in any other kind of work incidental to, or connected with the manufacturing process or the subject of the manufacturing process. "Manufacturing process" means any process for making, altering, repairing, ornamenting, finishing, packing, oiling, washing, cleaning, breaking up, demolishing, or otherwise treating, adapting any article or substance with a view to its use, sale, transport, delivery or disposal or pumping oil, water sewage, or generating, transforming or transmitting power, or composing types for printing by letterpress, lithography, photogravure or other similar process or book- binding, which is carried on by way of trade or for purposes of gain, or incidentally to another business so carried on, or constructing, reconstructing, repairing, refitting, finishing or breaking up ships or vessels. Preliminary Licensing and registration, Sections 6 and 7.—The owner or occupier of any premises which is liable to be treated as a "Factory" as defined under the Act shall get it registered and obtained from the Chief Inspectors of Factories a licence after paying the prescribed fee. He shall also get the plans etc. approved before using the premises as a "factory". Working hours, Holidays, intervals for rest, etc. 1. Hours of work {adults), Sections 51 and 54.—-No adult worker shall be required, or allowed, to work in a factory for more than 48 hours in any week and for more than nine hours in any day; provided that, subject to the previous approval of the Chief Inspector of Factories, the daily maximum specified in Section 54 may be exceeded in order to facilitate the change of shifts. 2. Relaxation of hours of work {adults), Section 64.—The ordinary limits on working hours of adults may be relaxed in certain special cases, e.g. workers engaged on urgent repairs ; in preparatory or complementary work which must necessarily be carried on outside the limits laid down for general working of factory; in work which is necessarily so intermittent that the intervals during which they do not work while on duty ordinarily amount to more than the intervals for rest; in work which for technical reasons must be carried on continuously ; in making or supplying articles of prime necessity which must be made or supplied every day; in a manufacturing process which cannot be carried on except during fixed seasons, or at times dependent on the irregular action of natural forces; in engine rooms or boiler houses or in attending to power plant or transmission machinery in the printing of newspapers, which are held up on account of the breakdown of machinery ; in loading or unloading of Railway wagons. Except in the case of urgent repairs, the relaxation shall not exceed the following limits— (i) the total number of hours of work in any day shall not exceed ten; (ii) the total number of hours of overtime work shall not exceed 50 for any one quarter ; {iii) the spreadover inclusive of intervals for rest shall not exceed 12 hours in any one day. In the case of any or all adults workers in any factory, the ordinary limits on working hours of adults may be relaxed, for a period or periods not exceeding in the aggregate three months in any year, to enable the factory to deal with exceptional press of work. 3. Payment for overtime, Section 59.—Where a worker works in a factory for more than nine hours in any day or for more than 48 hours in any week, he shall, in respect of overtime work, be entitled to wages at the rate of twice its ordinary rate of wages. 4. Exemption of supervisory staff. Section 64.—Chapter VI of the Act— working hours of adults—does not apply to persons holding positions of supervision or management or employed in a confidential position in a factory. 5. Weekly holidays {adults), Section 52.—No adult worker shall be required or allowed to work in a factory on the first day of the week, unless he has, or will have, a holiday for a whole day on one of the three days immediately^ before or after the said day, and the manager of the factory has before the said day or the substituted day whichever is earlier, delivered a notice at the office of the Inspector of his intention to require the worker on the said day and of the day which is to be substituted, and displayed a notice to that effect in the factory : Provided that no substitution shall be made which will result in any worker working for more than ten days consecutively without a holiday for a whole day. Where a worker in a factory, as a result of exemption from the ordinary provision relating to weekly holidays, is deprived of any of the weekly holidays, he shall be allowed, within the month in which the holidays were due to him or within the two months immediately following that month, compensatory holidays of equal number to the holidays so lost. 6. Intervals for rest {adults). Sections 55 and 56. —The periods of work of adult workers in a factory each day shall be so fixed that no period shall exceed 5 hours before he has had an interval for rest of at least half an hour and that inclusive of his intervals for rest they shall not spreadover more than 101 hours in any day or with the permission of the Chief Inspector in writing, 12 hours : Provided that the State Government or subject to the control of Slate Government the Chief Inspector of factories may by written orders, and for the reasons specified therein, exempt any factory in such a way that the total number of hours put in by a worker without an interval, does does not exceed six. 7. Prohibition of double employment, Sections 60, 71 and 99.—No child or, except in certain circumstances an adult worker, shall be required or allowed to work in any factory on any day on which he has already been working in any other factory. If a child works in a factory on any day on which he has already been working in another factory, the parent or guardian of the child or the person having custody of or control over him or obtaining any direct benefit his wages, shall be punishable with fine, which may extend to Rs. 50 un appears to the court that the child so worked without the consent or connivance of such parent, guardian or person. 8. Prohibition of employment of children under 14, Section 67.—No child, who has not completed his fourteenth year, shall be required or allowed to work in any factory. 9. Hours of work [children), Section 71.—No child shall be employed or permitted to work in any factory for more than 4½ hours in any day and ; during the night, which shall mean a period of at least twelve consecutive hours including the period between 10 p.m. and 6 a.m. The periods of work of all children employed in a factory shall be limited to two shifts which shall not overlap or spread over more than 5 hours each and each child shall be employed in. only one of the relays. The provision relating to weekly holidays shall also apply to child workers and no exemption from the provision may be granted in respect of any child. 10. Prohibition of employment of women, Section 66.—No women shall in any circumstances be employed in any factory more than 9 hours in any day or between the hours of 7 p.m. and 6 a.m. and there shall be no change of shifts except after a weekly or any other holiday. Leave with wages 11. Annual leave with wages, Sections 79, 80, 82 and 83.—Every worker, who has worked for a period of 240 days or more in a factory during a calendar year, shall be allowed during the subsequent calendar year leave with wages for a number of days calculated at the rate of— (i) if an adult, one day for every twenty days of work performed by him during the previous calendar year ; (ii) if a child, one day for every fifteen days of work performed by him during the previous calendar year. Any days of lay off, by agreement or contract or as permissible under the standing orders maternity leave for any number of days not exceeding twelve weeks in the case of a female worker, and leave earned in the year prior to that in which leave is enjoyed, shall be deemed to be days on which tin; worker has worked in a factory for the purpose of computation of the period of 240 days or more but he shall not earn, leave for these days : Provided that a period of leave shall be exclusive of ail holidays whether occurring during or at either end of the period of leave. A worker, who quits his employment on or before the next pay day of January, shall be entitled Lo leave with wages at the rate as laid down in clause (i) or (ii) above, as the ease may be, if he has worked for two-thirds of the total number of days in the remainder of the calendar year. If a worker is discharged or dismissed from service during the course of the year, he shall be entitled to leave with wages calculated at the rate as laid down above, even if he has not worked for the entire period as specified in clauses (i) and (ii) above entitling him to earned leave. In calculating leave under Section 79, half a day or more shall be treated as one full day and fraction of less than half shall be omitted. If a worker does not in any calendar year take the whole of the leave admissible to him, any leave not taken by him shall be added to the leave to be allowed to him in the succeeding calendar year : Provided that the total number of days of leave that may be carried forward to the succeeding year shall not exceed 30 in the case of an adult and 40 in, the case of a child : Provided further that a worker, who has applied fin leave with wages but has not been given such leave shall be entitled to carry forward the unavailed leave without any limit. A worker may at any time apply for leave with wages but not less than fifteen days before the date on which he wishes his leave to begin, to take all leave or any portion thereof allowable to him during the calendar year: Provided that the application shall be made not less than thirty days before the date on which a worker wishes his leave to begin ii he is employed in a public utility service as defined in clause (n) of Section 2 of the Industrial Disputes Act, 1947 (XIV of 1947) : Provided further that the number of times in which the leave ma\ be taken during any year shall not exceed three. If a worker wants to avail himself of the leave with wages due to him to cover a period of illness, he shall be granted such leave even if his application for leave is not made within the time specified above. Where the employment of a worker, who is entitled to leave, is terminated by the occupier before he has taken the entire leave to which he is entitled, or if having applied for and having not been granted such leave, the worker quits his employment before he has taken the leave the occupier of the factory shall pay him the amount payable under Section 80 in respect of the leave not taken and such payment shall be made, where the employment of the worker is terminated by occupier, before the expiry of the second working day after such termination and where a worker who quits his employment on or before the next pay day. For the leave allowed to him under Section 79, a worker shall be paid at a rate equal to the daily average of his total full time earnings for the days on which he worked during the month immediately preceding his leave, exclusive of any overtime and bonus, but inclusive of dearness allowance and the cash equivalent to the advantage accruing through the concessional sale to the worker of foodgrains and other articles. A worker, who has been allowed leave for not less than four days in the case of an adult, and five days, in the case of a child, shall before his leave begins, be paid the wages due for the period of leave allowed. The Manager shall maintain an account of the leave with wages in a register which shall be on the prescribed Form No. 14 and shall provide each worker with a book called the "Leave Book'', on the lines of Form No. 15. The Leave Book shall be the property of the worker and the Manager or his agent shall not demand it except to make entries of the dates of leave or interruptions in service and shall not keep it for more than a week at a time, if a worker loses his Leave Book, the Manager shall provide him with another copy on payment of four annas and shall complete it from his record. Any sum required to be paid by an employer, for leave with wages, but not paid by him shall be recoverable as delayed wages under the provisions of the Payment of Wages Act, 1936 (Act No. IV of 1936). Health 12. Cleanliness, Section 11.—Except in cases specially exempted, all inside walls and partitions, all ceilings or tops of rooms and all walls, sides and tops of passages and stairscases in a factory shall be kept white-washed or colour washed. The white-washing or colour washing shall be carried out at least once in every period of fourteen months. The floors of every work-room shall be cleaned at least once in every week by washing, using disinfectant, where necessary, or some other method. 13. Disposal of wastes and effluents, Section 12.—Effective arrangements shall be made m every factory for the disposal of wastes and effluents due to the manufacturing process carried on therein. 14. Ventilation and temperature, Section 13.—Effective and suitable provision shall be made in every factory for securing and maintaining in every work-room adequate ventilation by the circulation of fresh air and such a temperature as will secure to workers therein reasonable conditions of comfort and prevent injury to health. 15. Overcrowding, Section 16.—Unless exemption has been granted, there shall be in every work-room of a factory in existence on April 1, 1949 at least 350 cubic feet and of a factory built after this date at least 500 cubic feet of space for every worker employed therein and for this purpose no account shall be taken of any space which is more than 14 feet above the level of the floor of the room. 16. Lighting, Section 17.—In every part of a factory, where workers are working or passing, there shall be provided and maintained sufficient and suitable lighting, natural or artificial or both. 17. Drinking water, Section 18.—In every factory effective arrangement shall be made to provide and maintain at suitable points, conveniently situated for all workers employed therein, a sufficient supply of wholesome drinking water. In every factory wherein more than 250 workers are ordinarily employed, the drinking water shall during the hot weather, be cooled by ice or other effective means. The cooled drinking water shall be supplied in every canteen-lunch-room and rest room and also at conveniently accessible points throughout the factory. 18. Latrines and urinals, Section 19 and rules.—In every factory sufficient latrine and urinal accommodation of the prescribed type (separate enclosed accommodation for male and female workers) shall be provided conveniently situated and accessible to workers at all times while they are at the factory. Every latrine shall be under cover and so partitioned off as to secure privacy and shall have a proper door and fastenings. Sweepers shall be employed whose primary duty it would be to keep clean latrines, urinals and washing places. 19. Spittoons, Section 20.—In every factory, there shall be provided a sufficient number of spittoons of the type prescribed in convenient places and they shall be maintained in a clean and hygienic condition. No person shall spit within the premises of a factory except in the spittoons provided for the purpose. Whoever spits in contravention of this provision shall be punishable with fine not exceeding five rupees. Safety 20. Fencing of machinery, Section 21.—In every factory, mover and every flywheel connected to a prime mover or dangerous parts of machines, e. g. every moving part of a prime mover, etc. shall be securely fenced by safeguards of substantial construction which shall be kept in position while the parts of machinery they are fencing are in motion or in use.

Previous and next

All provisions of Uttar Pradesh Factory Rules, 1950

Questions people ask

Is rule 5310 of Uttar Pradesh Factory Rules, 1950 still in force?

No repeal of Uttar Pradesh Factory Rules, 1950 is recorded.