Rule 56, Uttar Pradesh Factory Rules, 1950: Mode of application
Uttar Pradesh Factory Rules, 1950 - Rule 56
Text of rule 56
Mode of application
56. Mode of application.— . In the said rules, rule 6 shall be omitted.6
5[7. Registration and grant of licence.—(1) Registration and grant of licence-The
factory shall be registered and a licence for a factory shall be granted by the Chief
Inspector in Form 3 on payment of the fees specified in the Schedule below:-
Schedule of fees payable
Quantity of HP
installed
(maximum H.
P.)
Maximum number of persons to be employed on anyday during the
calendar year
Up
to
50
Fro
m 51
to 150
From
151
to 250
From
251
to
500
From
501
to
1000
From
1001
to
2500
Above
2500
01 02 03 04 05 06 07 08
Rs. Rs. Rs. Rs. Rs. Rs. Rs.
Nil 150 700 900 1700 3500 6500 10000
Up to 50 600 1800 2800 3700 6800 12500 14000
Above 50 but
not above 100
1200 2700 3600 5700 9000 15000 18000
Above 100 but
not above
500
2500 5500 7200 9600 14400 22000 25000
Above 500 but
not above
1000
5000 7500 9400 12000 18000 14500 30000
Above 1000 but
not above
2000
6000 9500 11500 14000 19000 26500 32000
Above
2000
7000 12500 14500 16500 24000 29000 35000
5
Subs. by Noti. No. 2237/XXXVI-3-7 (F)-87, dt. 23.7.1993 (w.e.f. 23.7.1993).
6
THE Governor is pleased to order the publication of the following English translation of
notification no. 90/XXXVI-3-2018-83 (Sa)-17, dated March 13, 2018
(2) Every licence granted or renewed under these rules shall remain in force for the
period prescribed in sub-rulc (1) of rule 9 from the date on which it is granted or
renewed.
5. In the said rules, after rule 7 the following rule shall be inserted, namely:-
7A-Display of sign board
Every occupier or manager shall display a painted sign board, with conspicuous letters
written in white or luminous paint of any colour, at the main entrance of the factory
giving the following particulars:-
1. Registration or licence number of factory.
2. Name of the factory.
3. Address of the factory (giving plot no., locality, street, PIN code etc.)
4. Name of the occupier.
5. Name of the manager.
6. In the said rules, for rule 9 set out in column-1 below the rule as set out in column-2
shall be substituted, namely:-
5[8. Amendment of licence.—(1) A licensee shall get his licence amended when
the factory exceeds the limits specified in the licence in regard to horse-power or
the number of persons employed.
(2) The fee for the amendment of a licence shall be ten rupees-plus the amount (if
any), by which the fee that would have been payable if the licence had originally
been issued in the amended form exceeds the fee originally paid for the licence.]
9. Renewal of Licence-
7
(1) The licence of a factory may be renewed by the Chief
Inspector for ten years at a time on payment of requisite fee specified in the Schedule to
rule 7 for every year.
However, the factories which come under purview of section 2(cb) of the Factories Act,
1948, their licences may be renewed for five years at a time on payment of requisite fee
specified in the Schedule to rule 7 for every year and the licenses for the factories which
also come under the purview of rule 2(ja) of the Manufacture, Storage and Import of
Hazardous Chemicals Rules, 1989, may be renewed for three years at a time on payment
of requisite fee specified in the Schedule to rule 7 for every year:
Provided that if the application for renewal is not received within the time specified in
sub-rule (2), the licence shall be renewed only on payment of a fee twenty five per cent in
excess of the fee ordinarily payable for the renewal of the licence:
Provided further that the State Government may, by general or special order, extend the
time for presentation of application for renewal of a licence.
(2) Every application for the renewal of licence shall be sent online in Form no. 4 so as to
reach the office of the Chief Inspector before two months of expiry of validity period and
if the application is so made, the premises shall be held to be duly licenced until such date
as the Chief Inspector renews the licence. However, the factories which come under
7
THE Governor is pleased to order the publication of the following English translation of
notification no. 90/XXXVI-3-2018-83 (Sa)-17, dated March 13, 2018
purview of section 2(cb) of the Factories Act, 1948, their licences may be renewed for
five years at a time on payment of requisite fee specified in the Schedule to rule 7 for
every year and the licenses for the factories which also come under the purview of rule
2(ja) of the Manufacture, Storage and Import of Hazardous Chemicals Rules, 1989, may
be renewed for three years at a time on payment of requisite fee specified in the Schedule
to rule 7 for every year:
Provided that if the application for renewal is not received within the time specified in
sub-rule (2), the licence shall be renewed only on payment of a fee twenty five per cent in
excess of the fee ordinarily payable for the renewal of the licence:
Provided further that the State Government may, by general or special order, extend the
time for presentation of application for renewal of a licence.
(2) Every application for the renewal of licence shall be sent online in Form no. 4 so as to
reach the office of the Chief Inspector before two months of expiry of validity period and
if the application is so made, the premises shall be held to be duly licenced until such date
as the Chief Inspector renews the licence.
(3) The form no. 4 duly filled in shall be sent online by the occupier every year inspite of
the renewal for more than one year so that it may reach the office of the Chief Inspector
on or before thirty first day of October every year.
(4) The application for the renewal of licence of a factory shall be disposed within fifteen
working days of the date of application online except those factories which are covered
under section 2 (ch) of the Factories Act, 1948 (Act 63 of 1948) or rule 2(ja) of the
Manufacture, Storage and Import of Hazardous Chemicals Rules, 1989 whose licence
renewal applications shall be disposed within thirty working days. If the application for
the renewal of licence is not rejected within the said time limit, the licence shall be
deemed to have been renewed and the Chief Inspector shall send immediately the
renewed licence to applicant and also inform the applicant on his e-mail address and his
registered mobile number.
10. Transfer of licence.—(1) The holder of a licence may, at any time before the
expiry of the licence, apply for permission to transfer his licence to another
person.
(2) Such application shall be n de to the Chief Inspector, who shall, : if he
approves of the transfer, enter upon the licence, under his signature, an
endorsement to the effect that the licence has been transferred to the person
named.
(3) A fee of five rupees shall be charged on each such application.
(4) The person to whom the licence is so transferred shall enjoy the same
powers, and be subject to the same obligations under the licence as the original
holder.
11. Procedure on death or disability of licensee.—If a licensee dies or becomes
insolvent or otherwise disabled, the person carrying on the business of such
licensee shall not be liable to any penalty, under the Act or these rules for
exercising the powers granted to the licensee by the licence during such time as
may reasonably be required to allow him to make an application for the transfer
of the licence under Rule 10 in his own name for the unexpired portion of the
original licence.
12. Loss of licence.—Where a licence granted under these rules is lost or
accidentally destroyed, a duplicate licence may be granted on payment of a fee of
rupees five.
13. Payment of Fees 8(1) Every application under these rules shall be
accompanied by a treasury receipt, showing that the appropriate fee have been
paid into the local treasury under the head of account, 0230- श्रम और सेवायोजन
104- फैक्ट्री अधिननयम के अन्तर्गत वसूऱ फीस"
(2) If an application for the grant or renewal of a licence is rejected, the fee paid
shall be refunded.
A—Miscellaneous Departments—Miscellaneous— 'Fees for licensing of
Factories' ".
(2) if an application for die grant, renewal or amendment of a licence is rejected,
the fee paid shall be refunded.
(3) Licence shall be obtained for die whole of the year :
Provided that in case of die factories newly registered, licence may be obtained
only for the remaining part of die year; for which die fees payable under sub-rule
(1) of Rule 7 shall be proportionately less, but shall be chargeable to the nearest
quarter, i.e., die period, January to March, April to June, July to September and
October to December.
14-A. Suspension of licence.—(1) If before October 31, of any year an occoupier
notifies his intention in writing to the Chief Inspector that during the year
following, the premises, in respect of which licence is issued will not be used for
8
THE Governor is pleased to order the publication of the following English translation of
notification no. 90/XXXVI-3-2018-83 (Sa)-17, dated March 13, 2018
the working of the factory, the Chief Inspector may suspend the licence granted
in respect of such factory.
(2) A licence suspended under sub-rule (1) may be revived on receipt of an
application for renewal accompanied by the licence and Form No. 4 for the
remaining quarters of the year on payment of the fees for such quarters and a
surcharge of 25 per cent of the fees for the quarters for which the licence
remained suspended.
14-B. Cancellation of licence.—The State Government, or the Chief Inspector,
with the approval of the State Government may after giving the licensee
concerned, reasonable opportunity to show cause against the proposed action,
cancel any licence, if it/he is satisfied that the licence was obtained by the
licensee through fraud, or by misrepresentation of facts/and on such cancellation
of licence the licensee shall not be entitled to the refund of the licence fee.
14-C. [Section 7(1)].— The notice of occupation shall be in Form 4.
[14-D. Notice of change f Manager.—The notice of change of manager referred
to in sub-section (4) of Section 7 of the Act shall be in Form No. 4-A.]
[14-E. Qualifications for the post of an Inspector.—Qualifications for the post of
an Inspector for the purposes of sub-section (1) of Section 8 of the Factories Act,
1948 (Act No. LXIII of 1984), shall be the same as prescribed for the post of
Inspector of Factories, in the Uttar Pradesh Inspector of Boilers and Factories
Service Rules, 1980.]
CHAPTER II
THE INSPECTION STAFF
Additional Powers [Section 9(c)]
[15. Powers of Inspectors.—(1) An Inspector shall for the purposes of the
execution of the Act have power to do all or any of the following things, that is to
say—
(a) to photograph any worker, to inspect, examine, measure, copy, photograph,
sketch or test, as the case may be, any building or room; and plant, machinery
appliance or apparatus; any register or document; or anything provided for the
purpose of securing the health, safety or welfare of the workers employed in a
factory or a place which the Inspector has reasons to believe is a factory and to
call for explanations for irregularities found, if any;
(b) in the case of an Inspector, who is a duly qualified medical practitioner to
carry out such medical examination as may be necessary for the purposes of his
duties under the Act;
(c) to prosecute, conduct or defend before a court any complaint or other
proceedings arising under the Act or in discharge of his duties as an Inspector :
Provided that the powers of District Magistrates and such other public officers as
are appointed to the Additional Inspector shall be limited to the administration
of the following provisions of the Act, namely the provisions relating to—
Health (Chapter III), Employment of young persons on dangerous machines
(Section 23), Prohibition of employment of women and children near cotton
openers (Section 27), Precautions against dangerous fumes (Section 36),
Explosive or inflammable dust, gas, etc. (Section 37), Precautions in case of fire
(Section 38); Welfare (Chapter V), Working hours of Adults (Chapter VI) (except
the power of exemption under the provision to Section 62). Employment of
young persons (Chapter VII), Annual leave with wages (Chapter VIII) and
display of notice (Section 108).
(2) Identification cards.—(a) All Inspecting Officers shall if requested, produce an
authorised identification card.
(b) Identification cards would be issued for all Additional Inspectors of Factories
belonging to Medical and Public Health Department, by the Director of Medical
and Health Services. For Officers of the Labour Department, the Identification
cards would be issued by the Labour Commissioner and for the Executive
Magistrates, by the District Magistrates of the Districts concerned.
Duties of Certifying Surgeons and Authorized Medical Practitioners
[Section 10(4)]
16. Duties of Certifying Surgeons.—(1) For purposes of the examination and
certification of young persons, who wish to obtain certificates of fitness, the
Certifying Surgeon shall arrange a suitable time and place for the attendance of
such persons, and shall give previous notice in writing of such arrangements to
the managers of factories situated within the local limits assigned to him.
(2) The Certifying Surgeon shall issue his certificates in Form No. 5. The foil and
counterfoil shall be filled in and left thumb-impression of the person in whose
name the certificate is granted shall be taken on them. On being satisfied as to the
correctness of the entries made therein and of the fitness of the persons
examined, he shall sign the foil and initial the counterfoil and shall deliver the
foil to the person in whose name the certificate is granted. The foil so delivered
shall be the certificate of fitness granted under Section 69 of the Act. All
counterfoils shall be kept by the Certifying Surgeon for a period of at least two
years after the issue of the certificate.
9(3) The Certifying Surgeon shall, upon request by the Chief Inspector or an
Inspector of Factories carry out such examination and furnish him with such
report as he may indicate, for any factory or class or description of factories
where—
(a) cases of illness have occurred which it is reasonable to believe are due to the
nature of the manufacturing process carried on, or other conditions of working
prevailing therein, or
(b) by reason of any change in the manufacturing process carried on, or in the
substance used therein, or by reasons of the adoption of any new manufacturing
process or of any new substance for use in a manufacturing process, there is a
likelihood of injury to the health of workers employed in that manufacturing
process, or
(c) young persons are, or are about to be employed in any work, which is likely
to cause injury to their health.
(4) For the purpose of the examination of persons employed in processes
covered by the Dangerous Operations Rules, the Certifying Surgeon shall visit
the factories within the local limits assigned to him at such intervals as are
prescribed by the rules applying to any particular factory,
(5) At such visits the Certifying Surgeon shall examine the persons employed in
such processes and shall record the results of his examination in a register known
as the Health Register which shall be kept by the factory manager and produced
before the Certifying Surgeon at each visit.
(6) If the Certifying Surgeon finds as a result of his examination that any person
employed in such process is no longer fit for medical reasons to work in that
process, he shall suspend such person from working in that process for such time
as he may think fit and no person after suspension shall be employed in that
process without the written sanction of the Certifying Surgeon in the Health
Register.
(7) The manager of a factory shall afford to the. Certifying Surgeon facilities to
inspect any process in which any person is employed or likely to be employed.
(8) The manager of a factory shall provide for the purpose of any medical
examination which the Certifying Surgeon wishes to conduct at the factory (for
his exclusive use on the occasion of an examination) a room which shall be
properly cleaned and adequately ventilated and lighted and furnished with a
screen, a table (with writing materials) and chairs.
CHAPTER III
EXEMPTION IN RESPECT OF PAINTING, LIME-WASHING, ETC.
OF WALLS AND CEILINGS, ETC.
[Section 112]
17. Cleaning of walls and ceilings.—(1) Clause (d) of sub-section (1) of Section 11
of the Act shall not apply to the classes or descriptions of factories or parts of
factories specified in the schedule to this rule provided that they are kept in a
clean state by washing, sweeping, brushing, dusting, cleaning or other effective
means:
Provided further that the said clause (d) shall continue to apply—
(a) as respects factories or parts of factories specified in Part A of the said
Schedule, to work-rooms in which the amount of cubic space allowance for every
person employed in the room is less than 500 cubic feet;
(b) as respects factories or parts of factories specified in Part B of the said
Schedule, to work- rooms in which the amount of cubic space allowed for every
person employed in the room is less than 2,500 cubic feet;
(c) to engine house, fitting shops, lunch-rooms, canteens, shelters, creches,
cloak-rooms and wash-places; and
(d) to such parts of walls, sides and tops of passages and staircases as are less
than 20 feet above the floor or stair.
(2) The record of dates on which white-washing, colour-washing, varnishing,
etc., are carried out shall be entered in a register maintained in Form No. 8.
(3) If it appears to the Chief Inspector that any part of a factory to which, by
virtue of this rule, any of the provisions in clause (d) of sub-section (1) of Section
11 of the Act do not apply, or apply as varied by this rule, is not being kept in a
clean state, he may, by a written notice, require the occupier to white-wash or
colour-wash, wash, paint or varnish the same. In the event of the occupier failing
to comply with such notice within two months from the date of the notice, this
rule shall cease to apply to such part of a factory unless and until the Chief of
Inspector otherwise determines.
SCHEDULE
PART A
(1) Blast Furnaces. (2) Iron and Steel Mills. (3) Copper Mills. (4) Stone, Slate and
Marble works. (5) Brick and tile works in which unglazed bricks or tiles are
made. (6) Cement Works. (7) Chemical Works, and (8) Gas Works.
The following parts of factories:
(a) Rooms used only for the storage of articles.
(b) Rooms in which the walls or ceilings consist of galvanized iron, glazed
bricks, glass, slate, asbestos, bamboo thatch or cement plaster.
(c) Parts in which dense steam is continuously evolved in the process.
(d) Parts in which pitch, tar or like material is manufactured or is used to a
substantial extent except in brush works. The parts of a glass factory known as
the glass-house. Rooms in which graphite is manufactured or is used to a
substantial extent in any process.
(e) Parts in which coal, coke, oxide of iron ochre, lime or stone is crushed on
ground.
(f) Parts of walls, partitions, ceilings or tops of rooms which are at least 20 feet
above the floor.
(g) Ceilings or tops of rooms in print works, bleach works or dye works, which
the exception of finishing rooms or ware-houses.
(h) Inside walls of oil mills below a height of 5 feet from the ground floor level.
(i) Inside walls in tanneries below a height of 5 feet from the ground floor level
where a wet process is carried on.
PART B
(1) Gun factories.
(2) Engineering Works.
(3) Electric generating or transforming stations.
(4) Foundries other than foundries is which brass casting is carried on.
(5) Factories in which sugar is referred or manufactured.
(6) Coach and motor-body works.
(7) Those parts of factories where unpainted or unvarnished wood articles are
manufactured.
Disposal of Trade Wastes and Effluents
[Section 12(2)]
[18. The arrangements made in accordance with sub-section (1) of Section 12 of
the Act for the treatment of wastes and effluents and for their disposal shall be in
accordance with the provisions contained in "The Water (Prevention and Control
of Pollution) Act, 1974 (Act No. VI of 1974) and shall be approved by the State,
Board constituted by the State Government under sub-section (1) of Section 4 of
the said Act (Act No. VI of 1974) from time to time.]
Ventilation and Temperature (Section 13)
19. (1) The total area of openings for ventilation in every work-room shall
ordinarily be in the ratio of not less than one square foot to every fifteen square
feet of floor spaces :
Provided that where it is intended to use artificial ventilation by means of forced
draught fans all the time that work is carried on, for instance, by air-
conditioning, the area of such openings shall be such as may be approved by the
Inspector.
(2) In every room in a jute mill where opening of bales, batching, machine
hackling, carding, preparing or any other process is carried on in which dust is
generated and inhaled to an extent likely to cause injury to the health of the
workers, efficient exhaust and inlet ventilators shall be provided to secure that
the dust is drawn away from the workers at, or as near as is reasonably possible,
to the point at which it is generated.
(3) In every room in a cotton mill where slasher sizing is carried on, an efficient
arrangement for the removal of the steam given off in the process of drying the
yarn shall be fitted to the satisfaction of the Inspector. Except in cotton mills
which are in existence at the time these rules come into force, slasher sizing shall
not be carried on in any room where any other process of manufacture is being
performed.
(4) In every factory where injurious, poisonous and asphyxiating gases, dust or
other impurities are used for or are evolved for any process carried on, all
practicable measures to the satisfaction of the Inspector shall be taken to protect
the workers against the inhalation of such gases, dust or other impurities.
Artificial Humidification (Section 15)
20. When artificial humidification not allowed.—There shall be no artificial
humidification in any room of a cotton spinning or weaving factory—
(a) by the use of steam during any period when the dry-bulb temperature of
that room exceeds 85 degrees ;
(b) at any time when the wet-bulb reading of the hygrometer is higher than that
specified in the following schedule in relation to the dry-bulb reading of the
hygrometer at that time, or as regarding a dry-bulb reading intermediate
between any two dry-bulb readings indicated consecutively in the schedule
when the dry-bulb reading does not exceed the wet-bulb reading to the extent
indicated in relation to the lower of these two dry-bulb readings :
SCHEDULE
Dry-bulb Wet-bulb Dry-bulb Wet-bulb
60 . . . . . . 58.0 91 85.0
61 . . . . . . 59.0 92 85.5
62 . . . . . . 60.0 93 86.0
63 . . . . . . 61.0 94 86.5
64 . . . . . . 62.0 95 87.0
65 . . . . . . 63.0 96 87.0
66 . . . . . . 64.0 97 87.5
67 . . . . . . 65.0 98 88.0
68 . . . . . . 66.0 99 88.5
69 . . . . . . 67.0 100 89.0
70 . . . . . . 68.0 101 89.5
71 . . . . . . 69.0 102 90.0
72 . . . . . . 70.0 103 90.0
73 . . . . . . 71.0 104 90.5
74 . . . . . . 72.0 105 90.5
75 . . . . . . 73.0 106 91.0
76 . . . . . . 74.0 107 91.0
77 . . . . . . 75.0 108 91.5
78 . . . . . . 76.0 109 91.5
79 . . . . . . 77.0 110 92.0
80 . . . . . . 78.0 111 92.0
81 . . . . . . 79.0 112 92.5
82 . . . . . . 80.0 113 92.5
83 . . . . . . 80.5 114 93.0
84 . . . . . . 81.0 115 93.0
85 . . . . . . 82.0 116 93.5
86 . . . . . . 82.5 117 93.5
87 . . . . . . 83.0 118 94.0
88 . . . . . . 83.5 119 94.0
89 . . . . . . 84.0 120 94.5
90 . . . . . . 84.5 . . 95.0
Provided, however, that this clause shall not apply when the difference between
the wet-bulb temperature as indicated by the hygrometer in the department
concerned and the wet-bulb temperature taken with a hygrometer outside in the
shade is less than 3.5 degrees.
21. Provision of Hygrometer.—In all departments of cotton spinning and
weaving mills wherein artificial humidification is adopted, hygrometer shall be
provided and maintained in such positions as are approved by the Inspector. The
number of hygrometers shall b^ regulated according to the following scales:
(a) Weaving Department.—One hygrometer for departments with less than 500
looms, and one additional hygrometer for every 500 or part of 500 looms in
excess of 500.
(b) Other Departments.—One hygrometer for each room of less than 300,000
cubic feet capacity and one extra hygrometer for each 200,000 cubic feet or part
thereof, in excess of it.
(c) One additional hygrometer for taking shade readings shall be provided and
maintained in a position approved by the Inspector, outside each cotton spinning
and weaving factory wherein artificial humidification is adopted.
22. Exemption from maintenance of Hygrometers.—When the Inspector is
satisfied that the limits of humidity allowed by the schedule to Rule 20(b) are
never exceeded, he may, for any department other than the Weaving
Department, grant exemption from the maintenance of the hygrometer. The
Inspector shall record such exemption in Form No. 6.
23. Copy of Schedule to Rule 29(b) to be affixed near every Hygrometer.—A
legible copy of the schedule to Rule 20(6) shall be affixed near each hygrometer.
24. Temperature to be recorded at each hygrometer.—At each hygrometer
maintained in accordance with Rule 21 correct wet and dry-bulb temperatures
shall be recorded thrice daily during each working day by competent persons
nominated by the manager. The temperature shall be taken between 7 a. m. and 9
a. m. and between 11 a. m. and 2 p. m. (but not in the rest interval) and between 4
p. m and 5.30 p. m. In exceptional circumstances, such additional readings and
between such hours, as the Inspector may specify, shall be taken. The
temperatures shall be entered in a Humidity Register Form No. 7 maintained in
the factory. At the end of each working day, the persons, who have taken the
readings shall sign the register and certify the correctness of the entries. The
register shall always be available for inspection by the Inspector.
25. Specifications of Hygrometer.—(1) Each hygrometer shall comprise of two
mercurial thermometers respectively, wet-bulb and dry-bulb of similar
construction and equal in dimensions, scale and divisions of scale. They shall be
mounted on a frame with a suitable reservoir containing water.
(2) The wet-bulb shall be closely covered with a single layer of muslin, kept wet
by means of a wick attached to it and dropping into the water in the reservoir.
The muslin covering and the wick shall be suitable for the purpose, clean and
free from size or grease.
(3) No part of the wet-bulb shall be within ¾ inches from the dry-bulb or less
than § inch from the surface of the water in the reservoir below it, on the side of
it away from the dry bulb.
(4) The bulb shall be spherical and of suitable dimensions and shall be freely
exposed on all sides to the air of the room.
(5) The bores of the stems shall be such that the position of the top of the
mercury column shall be readily distinguished at a distance of two feet.
(6) Each thermometer shall be graduated so that accurate readings may be taken
between 50 and 120 degrees.
(7) Every degree from 50 degrees up to 120 degrees shall be clearly marked by
horizontal lines on the stem, each fifth and tenth degrees shall be marked by
longer marks, than the intermediate degrees and the temperature marked
opposite each tenth degrees, i.e. 50, 60, 70, 80, 90, 100, 110 and 120.
(8) The markings as above shall be accurate, that is to say, at no temperature
between 50 and 120 degrees shall the indicated readings be in error by more than
two-tenths of a degree.
(9) A distinctive number shall be indelibly marked upon the thermometer.
(10) The accuracy of each thermometer shall be certified by the National Physical
Laboratory, London, or some competent authority appointed by the Chief
Inspector, and such certificate shall be attached to the Humidity Register.
26. The thermometers to be maintained in efficient order.—Each thermometer
shall be maintained at all times during the period of employment in efficient
working order, so as to give accurate indications and in particular:
(a) The wick and the muslin covering of the wet-bulb shall be renewed once a
week.
(b) The reservoir shall be filled with water which shall be completely renewed
once a day. The Chief Inspector may prescribe the use of distilled water or pure
rain water in any particular mill or mills in certain localities.
(c) No water shall be applied directly to the wick or covering during the period
of employment.
27. An inaccurate thermometer not to be used without fresh certificate.—If an
Inspector gives notice in writing that a thermometer is not accurate it shall not,
after one month from the date of such notice, be deemed to be accurate unless
and until it has been re-examined as prescribed and a fresh certificate obtained
which certificate shall be kept attached to the Humidity Register.
28. Hygrometer not to be fixed to wall, etc., unless protected by wood.—(1) No
hygrometer shall be fixed to a wall, pillar or other surface unless protected
therefrom by wood or other non-conducting material at least half an inch in
thickness and distant at least one inch from the bulb of each thermometer.
(2) No hygrometer shall be fixed at a height of more than 5 feet 6 inches from the
floor to the top of thermometer stem or in the draughts from a fan window, or
ventilating opening.
29. No reading to be taken within 15 minutes of renewal of water.—No
reading shall be taken for record on any hygrometer within 15 minutes of the
renewal of water in the reservoir.
30. How introduce steam for humidification.—In any room in which steam
pipes are used for the introduction of steam for the purpose of artificial
humidification of the air, the following provisions shall apply :
(a) The diameter of such pipes shall not exceed two inches, and in the case of
pipes installed after the date of enforcement of these rules, the diameter shall not
exceed one inch.
(b) Such pipes shall be as short as is reasonably practicable.
(c) All hangers supporting such pipes shall be separated from the bare pipes by
an efficient insulator not less than half an inch in thickness.
(d) No uncovered jet from such pipes shall project more than 4½ inches beyond
the outer surface of any cover.
(e) The steam pressure shall be as low as practicable and shall not exceed 70 lb.
per square inch.
(f) The pipes employed for the introduction of steam into the air in a department
shall be effectively covered with such non-conducting material, as may be
approved by the Inspector in order to minimize the amount of heat radiated by
them into the department.
Lighting Rules [Section 17(4)]
31. Lighting.—Save as provided in these rules, Rules 31 to 35 shall apply to
factories in which persons are being regularly employed in a manufacturing
process or processes for more than 48 hours a week, or in shifts; provided that
nothing in these rules shall be deemed to require the provision of lighting of a
specified standard in any building or structure so constructed that in the opinion
of the Chief Inspector it would not be reasonably practicable to comply with such
requirement.
32. Lighting of interior parts.—(1) The general illumination over these interior
parts of a factory, where persons are regularly employed shall be not less than 3
feet candles measured in the horizontal plane at a level of 3 feet above the floor :
Provided that, in any such parts in which the mounting height of the light source
for general illumination necessarily exceeds 25 feet measured from the floor or
where the structure of the room or the position or construction of fixed
machinery or plant prevents the uniform attainment of this standard, the general
illumination at the said level shall be not less than 1 foot candle and where work
is actually being done the illumination shall be not less than 6 feet candles.
(2) The illumination over all other interior parts of the factory over which
persons employed pass shall when and-where a person is passing be not less
than 0.5 foot candle at floor level.
(3) The standard specified in this rule shall be without prejudice to the
provision of any additional illumination required to render the lighting sufficient
and suitable for the nature of the work.
33. Prevention of glare.—(1) Where any source of artificial light in the factory
is less than 16 feet above floor level, no part of the source or of the lighting fitting
having a brightness greater than 10 candles per square inch shall be visible to
persons whilst normally employed within 100 feet of the source, except where
the angle of elevation from the eye to the source or part fitting of the case may be,
exceeds 20°.
(2) Any local light, that is to say artificial light designed to illuminate particularly
the area or part of the area of work of a single operative or small group of
operatives working near each other, shall be provided with a suitable shade of
opaque material to prevent glare or with other effective means by which the light
source is completely screened from the eyes of every person employed at a
normal working place, or shall be so placed that no such person is exposed to
glare therefrom.
34. Discretion of the Chief Inspector.—Where the Chief Inspector is satisfied
in respect of any particular factory or part thereof or in respect of any description
of work-room or process that any requirement of Rule 32 is inappropriate or is
not reasonably practicable, he may by order in writing (which he may at his
discretion revoke) exempt the factory or part thereof, or that particular
description of work-room or processes from such requirement to such an extent
and subject to such conditions as he may specify.
35. Exemption from Rule 32.—(a) Nothing in Rule 32 shall apply to the parts of
factories specified in Part I of the schedule to these rules.
(b) Nothing in sub-rule (1) of Rule 32 shall apply to the factories or parts of
factories respectively specified in Part II of the said schedule.
SCHEDULE
PART I
Parts of factories in which light sensitive photographic materials are made or
used in an exposed condition.
PART II
Cement works.
Works for the crushing and grinding of limestone.
Gas work.
Coke oven works. Electrical stations.
Flour mills. Breweries.
Parts of Factories in which the following are carried on:
Rooms used for the manufacture of clay pots.
Concrete or artificial stone making.
Conversion of iron into steel.
Smelting of iron ore.
Iron or steel rolling.
Hot rolling or forging, tempering or annealing of metals.
Glass blowing and other working in molten glass.
Tar distilling.
Petroleum refining and blending.
Drinking water [Section 18(4)]
[36. Quantity, supply of drinking water—(1) The quantity of drinking water to
be provided for the workers in every factory shall be at least as many gallons a
day as there are workers employed in the factory and such drinking water shall
be readily available during working hours.
(2) The water so provided shall be supplied—
(a) from a public water supply system ; or
(b) from any other source approved in writing by the Health Officer.]
[37. Means of supply.—If drinking water is not supplied directly from taps
either connected with the public water supply system or any other water system
of the factory approved by the Health Officer, it shall be kept in suitable vessels,
receptacles or tanks fitted with taps and having dust proof covers placed on
raised stands or platforms in shade and having suitable arrangement of drainage
to carry away the split water. Such vessels or receptacles and tanks shall be kept
clean and the water renewed at least once every day. All practicable measures
shall be taken to ensure that water is free from contamination.]
[38. Cleanliness of well or reservoir.—(1) Drinking water shall not be supplied
from an open well or reservoir unless it is so constructed, situated, protected and
maintained as to be free from the possibility of pollution or chemicals, or
bacterical and extraneous impurities.
(2) Where drinking water is supplied from such well or reservoir the water in it
shall be sterilized once a week or more frequently if the Inspector by written
order so requires and the date, on which sterilizing is carried out, .hall be
recorded:
Provided that this requirement shall not apply to any such well or reservoir if the
water therein is filtered and treated to the satisfaction of the Health Officer
before it is supplied for consumption.
(3) Inspection.—(i) The drinking water shall be inspected twice a year by the
Health Officer in his capacity of Additional Inspector of Factories and where the
factory does not draw water from Municipal supplies or from supplies
supervised by the Medical staff of a Railway, or where infection is suspected,
samples of water shall be collected by the Health Officer and analysed at the cost
of the factory owner either in a local laboratory or at the State Health Institute,
Lucknow.
(ii) These analysis will be paid for by the factory owner, at the following rates:
Rs.
(a) Chemical analysis of each sample 20
(b) Bacteriological analysis of each sample 15
(c) Chemical and bacteriological analysis
combined
35
Provided that factories employing less than 100 persons shall be entitled to free
analysis, but if subsequently tests of water are rendered necessary because the
factory owner has failed to have a satisfactory sanitary installation, these
subsequent analysis shall be charged for at the rate prescribed above.
(iii) The manager or the occupier of the factory shall, in all cases, pay freight and
transportation charges of outfits for collection and dispatch of samples both
ways:
Provided that if a sample does not arrive safely at the Laboratory of the State
Health Institute to which it is sent, the employer concerned shall not be liable to
pay the freight and transportation charges for any subsequent samples taken in
lieu to the first.
(iv) The following will be the standard of purity of drinking water supplied to
factory workers :
Chemical
Filtered water supply, unfiltered water supplied from the tube-wells or
chemically treated water supplies—Chlorine ! .5 pails per million. Free ammonia
0.05 parts per million Albuminoid ammonia 0.1 parts per million.
Bacteriological
(1) Unchlorinated supplies from slow sand filters, protected wells springs or
others sources :
(a) Under 100 calories per c. c. of original water on Agarmedia.
(b) Presumptive coliform count in 48 hours 37° C.
Presumptive coliform count per 100 c. c.
Class I—Excellent—less than 1
Class II—Satisfactory 1-2
Class III—Suspicious 3-10
Class IV—Unsatisfactory greater than 10
Ordinarily a probable number of 2 coliform organisms 100 per c.c. in non-
chlorinated piped supplies is permitted, but throughout the year 50 per cent of
the samples should fall into Class I, 80 per cent should not fall below Class II and
the remainder should not fall below Class III.
(2) Chlorinated supplies (filtered or unfiltered from any source) :
(a) Under 100 calories per c.c. of original water per Agarmedia at 37°C.
(b) Presumptive coliform count in 48 hours at 37°C. presumptive coliform count
per 100 c.c.
Explanation.—Efficient chlorination should yield water free from coliform
organisms in 100 c.c., i.e., such water should come into Class I. Even making
allowance for sampling and other errors, the appearance of these organisms in
quantities of 100 c.c., i.e. a fall to Class 11 should at once occasion misgivings at to
the adequacy of the chlorination process.]
39. Report from Public Health Department.—Whenever it is found necessary
the Inspector may by an order in writing direct the manager to obtain, at such
time or at such intervals as he may direct a report from the Public Health
Department, Uttar Pradesh, as to the fitness for human consumption of the water
supplied to the workers, and in every case to submit to the Inspector a copy of
such report as soon as it is received from the said department.
In the case of Railway factories the certificate should be from the Medical Officer
of the Railway.
40. Cooling of water in every factory wherein more than two hundred and
fifty workers are ordinarily employed.—(a) The drinking water supplied to the
workers shall from May 1 to September 30, in every year, be cooled by an
effective method :
Provided that if ice is placed in the drinking water, the ice should be clean and
wholesome and shall be obtained only from a source approved in writing by the
Health Officer.
(b) The cooled drinking water shall be supplied in every canteen, lunch-room
and rest-room and also at conveniently accessible points throughout the factory
which for the purpose of these rules shall be called "water centres"
(c) The water centre shall be sheltered from the weather and adequately drained.
(d) The number of water centres to be provided shall be one "centre" for every
150 persons employed at any one time in the factory : Provided that in the case of
a factory where the number of persons employed exceeds 500, it shall be
sufficient if there is one such "centre" as aforesaid for every 150 persons up to the
first 500 and one for every 500 persons thereafter.
(e) Every "water centre" shall be in charge of a suitable person, who shall
distribute the water and maintain the "centre" in a clean and orderly condition.
The person in charge of the centre shall be provided with clean clothes while on
duty:
Provided that this clause shall not apply to any factory in which suitable
mechanically operated drinking water, refrigerating units or water taps
connected to a reservoir containing cool water are installed to the satisfaction of
the Chief Inspector.
Latrines and Urinals (Section 19)
41. The sanitary accommodation.—Latrine accommodation shall be provided in
every factory for the number of workers engaged at any one time on the
following scale :
(a) Where the number of workers does not exceed 50—one seat.
(b) Where the number of workers exceeds 50 but does not exceed 150— 4 seats.
(c) Where the number of workers exceeds 150 but does not exceed 250—5 seats.
(d) Where the number of workers exceeds 250—one seat for every 50 or fraction
of 50.
42. Latrines and public health requirements.—Latrines other than those
connected with an efficient water borne sewage system shall comply with the
requirements of the Public Health authorities.
43. Privacy of latrines.—Every latrine shall be under cover and so partitioned
off as to secure privacy, and each portion shall have a proper door and
fastenings.
44. Signboards on latrines.—Where workers of both sexes are employed there
shall be displayed outside each latrine a notice in the language understood by the
majority of the workers, "For men only" or "For women only" as the case may be.
The notice shall bear the figure of a man or of a woman as the case may be.
45. Urinal accommodation.—Urinal accommodation shall be provided for the
use of male workers and shall not be less than two feet in length for every 50
males: provided that where the number of males employed exceeds 500, it shall
be sufficient if there is one urinal for every 50 males up to the first 500 employed,
and one for every 100 thereafter; where women are employed separate urinal
accommodation shall be provided for them on the same scale.
In calculating the urinal accommodation required under this rule any odd
number of workers less than 50 or 100, as the case may be, shall be reckoned as
50 or 100.
46. Urinals to conform to Public Health requirements.—Urinals, other than
those connected with an efficient water-borne sewage system and urinals in a
factory wherein more than two hundred and fifty workers are ordinarily
employed shall comply with the requirements of the Public Health authorities.
47. Certain latrines and urinals to be connected to sewerage system.—When
any general system of underground sewerage with an assured water supply for
any particular locality is provided in a municipality, all latrines and urinals of a
factory situated in such locality shall, if the factory is situated within 100 feet of
an existing sewer, be connected with that sewerage system.
48. White-washing and colour-washing of latrines and urinals.—The walls,
ceilings and partitions of every latrine and urinal shall be whitewashed or
colour-washed and the white-washing or colour-washing shall be repeated at
least once in every period of four months. The dates on which the white-washing
or colour-washing is carried out shall be entered in Form No. 8:
Provided that this rule shall not apply to latrines and urinals, the walls, ceilings,
or partitions of which are laid in glazed tiles or otherwise finished to provide a
smooth, polished, impervious surface and that they are washed with suitable
detergents and disinfectants at least once in every period of four months.
49. Drains carrying waste or sullage water.—All drains carrying waste or
sullage water shall be constructed in masonry or other impermeable material and
shall be regularly flushed and the effluent disposed of by connecting such drains
with a suitable drainage line :
Provided that, where there is no such drainage line the effluent shall be
deodorized and rendered innocuous and then disposed of in a suitable manner
to the satisfaction of the Health Officer.
50. Water taps and reservoirs near latrines.—A suitable number of
conveniently accessible water taps or reservoirs shall be provided near each set
of latrines.
Spittoons [Section 20(2)]
51. Spittoons.— (1) The number and location of the spittoons to be provided
shall be to the satisfaction of the Inspector.
(2) The spittoons shall be cleaned and disinfected at least once every day.
(3) The spittoons shall be of either of the following types—
(a) a galvanised iron container with a conical funnel-shaped cover. A layer of
suitable disinfectant liquid shall always be maintained in the container ; or
(b) a container filled with dry, clean sand and covered with a layer of bleaching
powder and quick lime; or
(c) any other type approved by the Chief Inspector.
CHAPTER IV
SAFETY
Further precautions in respect of particular machinery
[Section 21(2)]
52. Safety precautions.— (1) Without prejudice to the provision of Section 21(1)
of the Factories Act, 1.948, in regard to the fencing of machinery, the following
additional provisions specified in the schedules annexed hereto shall apply to
machinery noted in each schedule, The provisions of this rule shall come into
force from July 1, 1951, in the case of factories registered before April 1, 1949.
(2) The fences and other devices for protection shall be so constructed and
designed as to render it impossible for any person to pass between them and a
moving part and also in such manner as to give protection to a person oiling,
cleaning or otherwise attending to machinery and to all persons, who may be in
the neighbourhood of moving part while it is in motion.
(3) In every fence the spaces between the fence framing shall be completely and
securely fitted in with panels of sheet metal, expanded metal or other stout and
durable material, unless the frame members of the fence are, in the opinion of the
Inspector, sufficiently close together to serve the same purpose. When panels are
fitted, the boards shall be ^fitted to all fences, which stand upon the ground or in
a wall-way, scaffold or platform.
(4) In case where a fixed fence cannot be used to give protection from flying
chips or the like, the manager shall provide portable screens where these can be
effectively used ; and where screens are not adequate protection, he shall provide
goggles for each worker within range.
(5) The guards and other appliances required by the rules shall be—
(a) maintained in an efficient state,
(b) constantly kept in position while the machinery is in motion, and
(c) so adjusted as to enable the work to be done without unnecessary risk.
(6) If the driving machinery is situated in a room separated from the driven
machinery room by a high wall, an Inspection door 4'x4'shall be provided in the
wall and further a bell arrangement shall be provided under the control of the
person attending the driven machinery.
SCHEDULE I (Cotton Textiles)
1. Cotton openers, scutchers, combined openers and scutchers, and lap machines, hard
waste breakers, etc.—(a) All cotton openers, scutchers, combined openers and
scutchers, scutcher and lap machines, hard waste breakers and similar machines
shall be driven by separate motors or from countershafts provided with fast and
loose pulleys and efficient belt shifting devices.
(b) In all openers, combined openers and scutcher, scutchers, scutcher-lap-
machines, hard waste breakers and similar machines, the beater covers and
doors which give access to any dangerous part of the machines shall be fitted
with effective inter-locking arrangements which shall prevent—
(i) the covers and doors being opened while the machine is in motion; and
(ii) the machine being re-started until the covers and doors are closed :
Provided that in respect of doors of openings, other than dirt doors or desk doors
such openings shall be so fenced as to prevent access to any dangerous parts of
the machine if effective inter-locking arrangement is not provided.
(iii) In all openers, combined openers and scutcher, scutchers, scutcher-lap
machines, hard waste breakers and similar machines, the openings giving access
to the dust chamber shall be provided with permanently fixed fencing, which
shall, while admitting light, yet prevent contact between any portion of a
worker's body and the beater gride bars.
2. Combined openers and scutcher, scutchers, scutcher-lap, silver-lap machine, derby
doublers and ribbon machines.—(a) The lap forming rollers shall be fitted with a
guard or cover which shall prevent access to the intake of the lap roller and
fluted rollers as long as the weighted rak is dowing; or
(b) The guard or cover shall be so locked that it cannot be raised until the
machine is stopped and the machine cannot be started until the guard or cover is
closed.
3. Carding machines.—All cylinder doors shall be secured by an automatic
locking device which shall prevent the door being opened until the cylinder has
ceased to revolve and shall render it impossible to restart the machine until the
door has been closed.
4. Speed frames.—Headstocks shall be fitted with automatic locking
arrangements which shall prevent the doors giving access to jack box wheels
being opened while the machinery is in motion and shall render it impossible to
restart the machine until the doors have been closed.
5. Self-acting mules.—The drive shall be fro n countershafts, which shall be
provided with fast and loose pulleys and efficient belt shifting devices.
6. Calender machines, etc.—In respect of calendering machines, mangles and
similar machines, all such machines shall be provided with an efficient "nip"
guard along the whole length on the intake side of each pair of bowls and similar
parts, which shall be so fitted and maintained, whilst the rollers of bowls are in
motion, as to prevent access to the point of contact of the rollers or bowls.
SCHEDULE II {Ginning Factories)
Line shafts.—(a) The line shaft or second motion in cotton ginning factories shall
be completely enclosed by a continuous wall or unclimbable fencing with only as
many openings as are necessary for access to the shaft or removing cotton seeds,
cleaning and oiling and such openings shall be provided with gates or doors
which shall be kept closed and locked.
(b) The feed mouth of the opener shall be fitted with a traverser or a grid guard
extending 4 feet over the lattice conveyer so as to render it impossible for the
operative to be within reach of the beaters when feeding on to the lattice.
SCHEDULE III (Wood working machinery)
1. Definitions.—For the purposes of this schedule—
(a) Wood-working machine means a circular saw, band saw, planning machine,
chain mortising machine or vertical spindle moulding machine operating on
wood or cork.
(b) Circular saw means a circular saw working in a bench (including a rack
bench) but does not include a pendulum or similar saw which is moved towards
the wood for the purpose of cutting operation.
(c) Band saw means a band saw, die cutting portion of which runs in a vertical
direction but does not include a long saw or band re-sawing machine.
(d) Planning machine means a machine for overhead planning or for
thicknessing or for both operations.
2. Stopping and starting device.—An efficient stopping and starting device shall
be provided on every wood-working machine. The control of this device shall be'
in such a position as to be readily and conveniently operated by the person in
charge of the machine.
3. Space around machines.—The space surrounding every wood-working
machine in motion shall be kept free from obstruction.
4. Floors.—The floor surrounding every wood-working machine shall be
maintained in good and level condition, and shall not be allowed to become
slippery, and as far as practicable shall be kept free from chips or other loose
material.
5. Training and supervision.—(a) No person shall be employed at a woodworking
machine unless he has been sufficiently trained to work that class of machine, or
unless he works under the adequate supervision of a person, who has a thorough
knowledge of the working of the machine.
(b) A person who is being trained to work a wood working machine shall be fully
and carefully instructed as to the dangers of the machine and the precautions to
be observed to secure safe working of the machine.
6. Circular saws.—Every circular saw shall be fenced as follows:
(a) Behind and in direct line with the saw there shall be a riving knife, which
shall have a smooth surface, shall be strong, rigid and easily adjustable, and shall
also conform to the following conditions:
(i) The edge of the knife nearer the saw shall form an arc of a circle having a
radius not exceeding the radius of the largest saw used on the bench.
(ii) The knife shall be maintained as close as practicable to the saw having regard
to the nature of the work being done at the time, and at the level of the bench
table the distance between the front edge of the knife and the teeth of the saw
shall not exceed half an inch.
(iii) For a saw of a diameter of less than 24 inches, the knife shall extend upwards
from the bench table to within one inch of the top of the saw, and for a saw of a
diameter of 24 inches or over shall extend upwards from the bench table to a
height of at least nine inches.
(b) The top of the saw shall be covered by a strong and easily adjustable guard,
with a flang at the side of the saw farthest from the fence. The guard shall be kept
so adjusted that the said flang shall extend below the roots of the teeth of the
saw. The guard shall extend from the top of the riving knife to a point as low as
practicable at the cutting edge of the saw.
(c) The part of the saw below the bench table shall be protected by two plates of
metal or other suitable material one on each side of the saw; such plates shall not
be more than six inches apart, and shall extend from the axis of the saw outwards
to a distance of not less than two inches beyond the teeth of the saw. Metal
plates, if not beaded, shall be of a thickness at least l/10th inch, or if beaded be of
a thickness of at least l/20th inch.
7. Push sticks.—A push stick or other suitable appliance shall be provided for
use at every circular saw and at every vertical spindle moulding machine to
enable the work to be done without unnecessary risk.
8. Band saws.—Every band saw shall be guarded as follows :
(a) Both sides of the bottom pulley shall be completely encased by sheet or
expanded metal or other suitable material.
(b) The front of the top pulley shall be covered, with sheet or expanded metal or
other suitable material.
(c) All portions of the blade shall be enclosed or otherwise securely guarded
except the portion of the blade between the bench table and the top guide.
9. Planning machine.—(a) A planning machine (other than a planning machine,
which is mechanically fed) shall not be used for overhead planning unless it is
fitted with a cylindrical cutter block.
(b) Every planning machine used for overhead planning shall be provided with
"bridge" guard capable of covering the full length and breadth of the cutting slot
in the bench, and so constructed as to be easily adjusted both in a vertical and
horizontal direction.
(c) The feed roller of every planning machine used for thicknessing except the
combined machine for overhead planning and thicknessing shall be provided
with an efficient guard.
10. Vertical spindle moulding machine.—(a) The cutter of every vertical spindle
moulding machine shall be guarded by the most efficient guard having regard to
the nature of the work being performed.
(b) The wood being moulded at a vertical spindle moulding machine shall, if
practicable, be held in a jig or holder of such construction as to reduce as far as
possible the risk of accident to the worker.
11. Chain mortising machines.—The chain of every chain mortising machine
shall be provided with a guard, which shall enclose the cutters as far as
practicable.
12. Adjustment and maintenance of guards.—The guards and other appliances
required under this schedule shall be—
(a) maintained in an efficient state;
(b) constantly kept in position while the machinery is in motion ;
(c) so adjusted as to enable the work to be done without unnecessary risk.
13. Exceptions.—Paragraphs 6, 8, 9 and 10 shall not apply to any woodworking
machine in respect of which it can be proved that other safeguards are provided,
maintained and used which rendered the machine as safe as it would be if
guarded in the manner prescribed in this schedule.
SCHEDULE IV— (Rubber Mills)
1. Installation of machines.—Mills for breaking down, cracking, grating, mixing,
refining and warming rubber or rubber compounds shall be so installed that the
top of the front roll is not less than forty-six inches above the floor or working
level. Provided that in existing installations where the top of the front roll is
below this height a strong rigid distance bar guard shall be fitted across the front
of the machine in such position that the operator cannot reach the nip of the rolls.
2. Safety devices.—(a) Rubber mills shall be equipped with—
(i) hoppers so constructed or guarded that it is impossible for the operators to
come into contact in any manner with the nip of the rolls ;
(ii) horizontal safety trip rods or tight wire cables across both front and rear,
which will, when pushed or pulled, operate instantly to disconnect the power
and apply the brakes, or to reverse the rolls.
(b) Safe-trip rods or tight wire cables on rubber mills shall extend across the
entire length of the face of the rolls and shall be located not more than sixty-nine
inches above the floor or working level.
(c) Safety-trip rods and tight wire cables on all rubber mills shall be examined
and tested daily in the presence of the manager or other responsible person and
if any defect is disclosed by such examination and test the mill shall not be used
until such defect has been remedied.
[52A. Building and structure.—No building wall, chimney, bridge tunnel, road,
gallery, stairway, ramp, floor platform—staging or other structure, whether of a
permanent or temporary character, shall be constructed, situated or maintained
in any factory in such manner as to cause risk of bodily injury.
52B. Machinery and plant.—No machinery or plant equipment shall be
constructed, situated, operated or maintained in any factory in such a manner as
to cause risk of bodily injury.
52C. Method of work.—No process of work shall be carried in any factory in
such a manner as to cause risk of bodily injury.
52D. Stacking or storing of Materials etc.—No materials or equipment shall be
stacked or stored in such a manner as to cause risk of bodily injury.]
Precautions for Persons attending to Machinery13—[S. 22(1) and (3)]
53. (a) No machinery or shaft in motion shall be cleaned by waste rags or similar
material h 'd in hand.
(b) Every shafting ladder shall be fitted with either hooks or some effee-tive
non-skid device and shall be free from cracks, broken rungs and other defects.
When necessary to prevent slipping another worker shall be provided to hold the
bottom of the ladder.
(c) No person engaged in oiling or adjusting belts or in any work whatsoever
"within reach"" of transmission machinery or any other machinery which the
Inspector considers dangerous, shall be allowed to wear loosely fitting clothes.
(d) The occupier shall be responsible for the supply of tight fitting clothing
without cost to the workers mentioned in Rule (c) all the time they are at work.
(e) Notices or posters in Hindi for the prevention of accidents shall be displayed
at conspicuous places in every room of the factory in which machinery is in use.
(f) The manager of every factory shall cause the contents of the notices or posters
to be explained to each worker in the language understood by him on his first
engagement and as often as there is a change in the work performed by him.
(g) The register as required in sub-section (1) of Section 22 of the1 Act shall be in
Form No. 25.
Dangerous Machines [Section 23(2) |
54. Employment of young persons on dangerous machines.—
The following machines are hereby prescribed as of such a dangerous character
that young persons shall not work at them unless the provisions of Section 23(1)
are complied with.
Power presses other than hydraulic presses : milting machines used in the metal
trades ; Guillotine machine ; Circular Saw : Platen Printing machines.
55. Rules under Section 28.—(1) A register shall be opened with the following
columns to record particulars of examination of hoists and lifts :
(i) Date of examination.
(ii) Number of hoists and lifts if more than one.
(iii) Details of examinations made.
(iv) Result of examination.
(v) Signature of examiner.
(vi) Designation and qualifications of the examiner.
(2) Exemption of certain hoists and lifts.—In respect of any class or description of
hoists or lift specified in the first column of the Schedule, the requirements of
Section 28 specified in the second column of said schedule and set opposite to
that class or description of hoist or lift shall not apply :
SCHEDULE
Class or description of hoist or lift requirements which shall not apply
(a) Hoist or lifts mainly
used for raising materials
for charging blast
furnaces or lime-kilns.
Sub-section 1(b) in so far as it requires a gate at the
bottom landing; sub-section 1(e).
(b) Hoists not connected
with mechanical power
and which are not used
for carrying persons.
Sub-section 1(b) in so far as it requires the hoist way
or liftway enclosure to be so constructed as to
prevent any person or thing from being trapped
between any part of the hoist or lift and any fixed
structure or moving part; sub-section (l)(e).
15Pressure plant testing, examination and other safety measures
in relation thereto
55-A.—(1) No lifting machine, and no chain, rope or lifting tackle, except fibre
rope or a fibre rope sling, shall be taken into use in any factory unless it has been
tested and all parts have been thoroughly examined by a competent person and
certificate to that effect, specifying the safe working load or loads, has been
obtained from that person and is kept available for inspection.
(2) (a) Every jib-crane, which is so constructed that die safe working load varies
with raising or lowering of the jib, shall have attached thereto either an automatic
indicator of safe working loads or an automatic jib-angle indicator and a table
indicating the safe working loads at the corresponding inclinations of the jib, or
corresponding radii of the load.
(b) A table showing the safe working loads of every kind and size of chain, rope
or lifting tackle in use, and, in the case of a multiple sling, die safe working loads
at different angles of-the legs, shall be posted in the storeroom or place where, or
in which, the chains, ropes or lifting tackles are kept, and in prominent positions
on the premises; and no rope, chain or lifting tackle, not shown in the table, shall
be used. However, the foregoing provisions of this paragraph shall not apply in
respect of such lifting tackle in the safe working load thereof, or in the case of a
multiple sling, safe working load at different angles of the legs, is plainly marked
upon it.
(3) The register to be maintained under clause (a)(iii) of sub-section (1) of Section
29 of the Act shall be—
(i) Name of occupier of the factory.
(ii) Address of the factory.
(iii) Distinguishing number or mark, if any, and description sufficient to identify
the lifting machine, chain, rope, multiple sling or die lifting tackle.
(iv) Date when the lifting machine, chain, rope, or multiple sling or lifting tackle
was first brought into use in the factory.
(v) Date and number of the certificate relating to any test and examination made
under sub-rules (1) and (7) together with the name and address of the person
who issued the certificate.
(vi) Date of each periodical thorough examination made under clause (a) (iii) of
sub-section (1) of Section 29 of the Act and sub-rule (6) and name and
designation of the person by whom it was carried out.
(vii) Date of annealing or other heat treatment of die chain and other lifting tackle
made under sub-rule (5) and name and designation of the person by whom it
was carried out.
(viii) Particulars of any defects affecting the sate working load found at any such
thorough examination or after annealing and of the steps taken to remedy such
defects.
The register shall be kept readily available for inspection.
(4) All rails on which a travelling crane moves and every track on which "the
carriage of a transporter or runway moves shall be of proper size and adequate
strength and have an even running surface and every such rail or track shall be
properly laid, adequately supported and properly maintained.
(5) All chains and lifting tackle except a rope sling shall unless they have been
subjected to such other heat treatment as may be approved by Chief Inspector of
Factories be effectively annealed under the supervision of a competent person at
the following intervals :
(i) All chains, slings, rings, hooks, shackles and swivels used in connection with
molten metal or molten slag or when they are made of half inch bar or smaller
once at least in every six months.
(ii) All other chains, rings, hooks, shackles and swivels in general use, once at
least in every twelve months :
Provided that chains and lifting tackle not in frequent use shall, subject to the
Chief Inspector^ approval, be annealed only when necessary. Particulars of such
annealing shall be entered in a register prescribed under sub-rule (3).
(6) Nothing in the foregoing sub-rule (5) shall apply to the following classes of
chains and lifting tackles :
(i) Chains made of malleable cast iron.
(ii) Plate link chains.
(iii) Chains, rings, hooks, shackles and swivels made of steel or of any non-
ferrous metal.
(iv) Pitched chains, working on sprocket or pocketed wheels.
(v) Rings, hooks, shackles and swivels permanently attached to pitched chains,
pulley blocks or weighing machines.
(vi) Hocks and swivels having screw threaded 17parts or ball bearing or other
case hardened parts.
(vii) Socket shackles secured to wire ropes by white metal capping.
(viii) Bordeaux connections.
(ix) Any chain or lifting tackle which has been subjected to the heat treatment
known as "normalizing" instead of annealing.
Such chains and lifting tackle shall be thoroughly examined by a competent
person once at least in every twelve months, and particulars entered in the
register kept in accordance with sub-rule (3).
(7) Every lifting machine, chain, rope and lifting tackle, except a fibre rope, or
fibre rope sling, which has been lengthened, altered or repaired by welding or
otherwise, shall, before being again taken into use, be adequately re-tested and
re-examined by a competent person and a certificate of such test and
examination be obtained and particulars entered in the register kept in
accordance with sub-rule (3).
(8) No person under 18 years of age and no person who is not sufficiently
competent and reliable shall be employed as driver of a lifting machine, whether
driven by mechanical power or otherwise, or to give signals to a driver.
[Section 31(2)]
56. [Pressure vessels or plant.—{1) Interpretation—In this rule-
(a) "design pressure" means the maximum pressure that a pressure vessel or
plant is designed to withstand safety when operating normally;
(b) "maximum permissible working pressure" means the maximum pressure at
which a pressure vessel or plant is permitted to be operated or used under this
rule and is determined by the technical requirements of the process;
(c) "plant" means a system of piping that is connected to a pressure vessel and is
used to contain a gas, vapour or liquid under pressure greater than the
atmospheric pressure, and includes the pressure vessel;
(d) "Pressure vessel" means an unfired vessel that may be used for containing,
storing, distributing, transferring, distilling, processing or otherwise handling
any gas, vapour or liquid under pressure greater than the atmospheric pressure
and includes any pipe line fitting or "other equipment attached thereto or used in
connection therewith ; and
(e) "competent person" means a person who is, in the opinion of the Chief
Inspector, capable by virtue of his qualifications, training and experience, of
conducting a thorough examination and pressure tests, as required, on a
pressure vessel plant, and of making full report on its condition.
(2) Exceptions—Nothing in this rule shall apply to—
(a) vessels having internal diameter not exceeding 150 millimeters and a
capacity not exceeding 142 litres ;
(b) vessels made of ferrous materials having an internal operating pressure not
exceeding 1 kilogram per square centimetre ;
(c) steam boilers, steam and feed-pipes and their fittings coining under the
purview of Indian Boilers Act, 1923 ;
(d) metal bottles or cylinders used for storage or transport of compressed gases
or liquified or dissolved gases under pressure covered by the Gas Cylinder
Rules, 1940 framed under the Indian Explosives Act, 1884;
(e) vessels in which internal pressure is due solely to the static head of liquid;
(f) vessels with a nominal water capacity not exceeding 500 litres connected in a
water-pumping system containing air that is compressed to serve as a cushion;
(g) vessels for nuclear energy application ;
(h) refrigeration plant having a capacity of 3 tons or less of refrigeration in 24
hours ; and
(i) working cylinders of steam engines or prime movers, feed pumps and steam
traps; turbine casings; compressor cylinders ; steam separaters or dryers ; steam
strainers; steam de-super-heaters ; oil separators; air receivers for fire sprinkler
installations ; air receiver of monotype machines provided the maximum
working pressure of the air receiver does not exceed 1.33 kilograms per square
centimetre and the capacity 85 litres, air receivers of electrical circuit breakers; air
receivers of electrical relays; a;r vessels on pumps ; pipe coils, accessories of
instruments and appliances such as cylinders and piston assemblies used for
operating relays and interlocking type of guards; vessels with liquids subjected
to static head only; and hydraulically operating cylinders other than any cylinder
communicating with an air loaded accumulator.
(3) Design and construction—-Every pressure vessel or plant used in a factory—
(a) shall be properly designed on sound engineering practice;
(b) shall be of good construction, sound material adequate strength and free
from any patent defects; and
(c) shall be properly maintained in a safe condition :
Provided that the pressure vessels or plant in respect of the design and
construction of which there is an Indian standard or a standard of the country of
manufacture or any other law or regulation in force, shall be designed and
constructed in accordance with the said standard, law or regulation, as the case
may be, and a certificate thereof shall be obtained from the manufacturer or from
the competent person which shall be kept and produced on demand by an
Inspector.
(4) Safety devices—Every pressure vessel shall be fitted with—
(a) a suitable safety valve or other effective pressure relieving device of adequate
capacity to ensure that the maximum permissible working pressure of the
pressure vessel shall not be exceeded. It shall be set to operate at a pressure not
exceeding the maximum permissible working pressure and when more than one
protective device is provided only one of the devices need be set to operate at the
maximum permissible working pressure and the additional device shall be set to
discharge at a pressure not more than 5 per cent in excess of the maximum
permissible working pressure ;
(b) a suitable pressure guage with dial range not less than 1.5 times the maximum
permissible working pressure, easily visible
and designed to show at all times the correct internal pressure and marked with
a prominent red mark at the maximum permissible working pressure of the
pressure vessel;
(c) a suitable nipple and globe valve connected for the exclusive purpose of
attaching a test pressure guage for checking the accuracy of the pressure gauge
referred to in clause (b) of this sub-rule;
(d) a suitable stop valve or valves by which the pressure vessel may be isolated
from other pressure vessels or plant or source of supply or pressure. Such a stop
valve or valves shall be located as close to the pressure vessel as possible and
shall be easily accessible; and
(e) a suitable drain cock or valve at the lowest part of the pressure vessel for the
discharge of the liquid or other substances that may collect in the pressure vessel:
Provided that it shall be sufficient for the purpose of this sub-rule if the safety
valve or pressure relieving device, the pressure gauge and the stop valve are
mounted on a pipe line immediately adjacent to the pressure vessel and where
there is a range of two or more similar pressure vessels served by the same
pressure load only one set of such mountings need be fitted on the pressure load
immediately adjacent to the range of pressure vessels, provided they cannot be
isolated.
(5) Pressure reducing devices—
(a) Every pressure vessel which is designed for a working pressure less than the
pressure at the source of supply, or less than the pressure which can be obtained
in the pipe connecting the pressure vessel with any other source of supply, shall
be fitted with a suitable pressure reducing valve or other suitable automatic
device to prevent the maximum permissible working pressure of the pressure
vessel being exceeded.
(b) To further protect the pressure vessel in the event of failure of the reducing
valve device, at least one safety valve having capacity sufficient to release all the
steam, vapour or gas without undue pressure rise as determined by the pressure
at the source of supply and the size of the pipe connecting the source of supply,
shall be fitted on the low pressure side of the reducing valve.
(6) Pressure vessel or plant being taken into use—
(a) No new pressure vessel or plant shall be taken into use in a factory after
coming into force of this rule unless it has been hydrostatically tested by
competent person at a pressure at least 1.3 times the design pressure, and no
pressure vessel or plant which has been previously used or has remained
isolated or idle for a period exceeding 2 months or which has undergone
alterations or repairs shall be taken into use in a factory unless it has been
thoroughly examined by a competent person externally, and internally, if
practicable and has been hydrostatically tested by the competent person at a
pressure which shall be 1.5 times the maximum permissible working pressure:
Provided, however, that the pressure vessel or plant which is so designed and
constructed that it cannot be safely filled with water or liquid or is used in
service when even some traces of water cannot be tolerated, shall be
pneumatically tested at a pressure not less than the design pressure or the
maximum permissible working pressure as the case may be:
Provided, further that the pressure vessel or plant which is lined with glass shall
be tested hydrostatically or pneumatically as required at a pressure not less than
the design pressure or maximum permissible working pressure, as the case may
be.
Design pressure shall not be less than the maximum permissible working
pressure and shall take into account the possible fluctuations of pressure during
actual operation.
(b) No pressure vessel or plant shall be used in a factory unless there has been
obtained from the maker of the pressure vessel or plant or from the competent
person a certificate specifying the design, pressure or maximum permissible
working pressure thereof and stating the nature of tests to which the pressure
vessel or plant and its fittings (if any) have been subjected and every pressure
vessel or plant so used in a factory shall be marked so as to enable, it to be
identified as to be the pressure vessel or plant to which the certificate relates and
the certificate shall be kept available for perusal by the Inspector.
(c) No pressure vessel or plant shall be permitted to be operated or used at a
pressure higher than its design pressure, or the maximum permissible working
pressure as shown in the certificate.
(7) In-service test and examinations—
(a) Every pressure vessel or plant in service shall be thoroughly examined by a
competent person—
(i) externally, once in every period of six months ;
(ii) internally, once in every period of twelve months :
Provided that if by reason of the construction of a pressure vessel or plant, a
thorough internal examination is not possible, this examination may by replaced
by a hydrostatic test which shall be carried out once in every period of two years:
Provided further that for a pressure vessel or plant in continuous process which
cannot be frequently opened, the period of internal examination may be
extended to four years; and
(iii) hydrostatically tested once in every period of four years :
Provided, that in respect of a pressure vessel or plant with thin walls such as
sizing cylinder made of copper or any other non-ferrous metal, periodic
hydrostatic test may be dispensed with subject to the condition that the
requirements laid down in sub-rule (8) are fulfilled:
Provided further that when it is impracticable to carry out thorough external
examination of any pressure vessel or plant every six months ,as required in sub-
clause (i) or if owing to its construction and use a pressure vessel or plant cannot
be hydrostatically tested as required in subclauses (ii) and (iii) a thorough
external examination of the pressure vessel or plant shall be carried out at least
once in every period of two years and at least once in every period of four years a
thorough systematic nondestructive test like ultrasonic test for metal thickness or
other defects of all parts of failure of which might lead to eventual rupture of the
pressure vessel or plant shall be carried out.
(b) The pressure for the hydrostatic test to be carried out for the purpose of this
sub-rule shall be 1.25 times the design pressure for 1.5 times the maximum
permissible working pressure, whichever is less.
(8) Thin walled pressure vessel or plant—(a) In respect of any pressure vessel or
plant of thin walls such as sizing cylinder made of copper or any other non-
ferrous metal, the maximum permissible working pressure shall be reduced at
the rate of 5 per cent of the original maximum permissible working pressure for
every year of its use after the first five year no such cylinder shall be allowed to
continue to be used for more than twenty years after it was first taken into use.
(b) If any information as to the date of construction, thickness of walls, or
maximum permissible working pressure is not available, the age of such
pressure vessel or plant shall be determined by the competent person in
consultation with 'the Chief Inspector from the other particulars available with
the Manager.
(c) Every new and second hand pressure vessel or plant of thin walls to which
repairs likely to affect its strength or safety have been carried out, shall be tested
before use to at least, 1.5 times its maximum permissible working pressure.
(9) Report by competent person—(a) If during any examination any doubt arises as
to the ability of the pressure vessel or plant to work safely until the next
prescribed examination the competent person shall record in the prescribed
register his observations, findings and conclusions with other relevant remarks
with reasons and may authorise the pressure vessel or plant to be used and kept
in operation subject to a lowering of maximum permissible working pressure, or
to more frequent or special examination or test, or subject to both of these
conditions.
(b) A report of every examination or test carried out shall be completed in Form
9 and shall be signed by the person making the examination or test, and shall be
kept available for persual by the Inspector at all hours when the factory or any
part thereof is working.
(c) Where the report of any examination under this rule specified any condition
for securing the safe working of any pressure vessel or plant, the pressure vessel
or plant shall not be used unless the specified condition is fulfilled.
(d) The competent person making report of any examination under this rule,
shall within seven days of the completion of the examination, send to the
Inspector a copy of the report in every case where the maximum permissible
working pressure is reduced or the examination shows that the pressure vessel
or plant or any part thereof cannot continue to be used with safety unless certain
repairs are carried out or unless any other safety measure is taken.
(10) Application of other laws—-(a) The requirements of this rule shall be in
addition to and without any prejudice to and not in derogation of the
requirements of any other law in force.
(b) Certificates of reports of any examination, or test of any pressure vessel or
plant to which sub-rules (7) to (9) do not apply, conducted or required to be
conducted under any other laws in force and other relevant record relating to
such pressure vessel or plant, shall be properly maintained as required under the
said law and shall be produced on demand by the Inspector.]
[56-A. Other safety measures.—In the case of oxygen prepared by electrolytic
process for the purpose of compressing, the purity of oxygen shall not fall at any
time below 99 per cent by volume.
(2) The electrical connexions of the electrolytic cell shall be so arranged as to
overrule the possibility of wrong connection of the terminals leading to reversal
of polarity.
(3) Oxygen and hydrogen pipe shall be painted with distinguishing colours to
eliminate the possibility of faulty connections and the connecting of the cells to
the right lines shall be carried out by a competent person nominated by the
Manager.
(4) Samples of oxygen shall be taken and tested for purity at both the ends of
the gas-pipes connecting the gas holder and the suction end of the compressor
after the supply of oxygen to the gas-holder is cut off completely from the cells
by means of a stop-valve. Testing of the gas for purity shall be reported
thereafter every hour and records maintained in a register which shall be
approved by the Chief Inspector of Factories in this behalf.
(5) Each plant shall be provided with at least two gas-holder so that while
oxygen of one of them completely isolated from the cells is being compressed,
the gas generated at the cells is collected in the other.
(6) Testing of purity of oxygen shall be carried out by a competent person
nominated by the manager and the person so nominated shall sign the register
against each set of readings to certify the correctness of the same.
Excessive Weights [Section 34(2)]
Previous and next
Questions people ask
Is rule 56 of Uttar Pradesh Factory Rules, 1950 still in force?
No repeal of Uttar Pradesh Factory Rules, 1950 is recorded.