LawGrids logoLAWGRIDS.ORG

Rule 33, Legal Metrology National Standards Rules, 2011: Repeal and savings

Legal Metrology National Standards Rules, 2011 - Rule 33

Text of rule 33

Repeal and savings

33. Repeal and savings.- (1) The Standardsof Weightsand Measures(National Standards) Rules, 1988 (herein under referred to as the said rules) are hereby repealed. Providedthat such repealshall not affect: (a) the previous operationsof the said rules or anything done or omitted to be dOrleor suffered therein; or (b) any right, privilege, obligatIonor liability acquired,accruedor incurred under the said rules; or (c) any penalty, forfeiture or punishment incurred in respect of any offence committed againstthe said rules; or ['lJ7T II--~ 3(ii)J 57 (d) any investigation, legal proceedingsor remedy in respect of any such right, privilege,obligation, liability, penalty, forfeiture or punishmentas aforesaid. And any such investigation, legal proceedingsor remedy may be instituted, continued or enforced and any such penalty, forfeiture or punishmentmay be imposedas if the said ruleshad not beenrescinded. (2) Notwithstandingsuchrepealanythingdoneor any action taken or purportedto have been done or taken including approval of letter, exemption granted, fees collected, any adjudication, enquiry or investigation commenced, license and registration of manufacturers, dealers, importers of weights and measures,or show cause notice, decision,determination, approval, authorisation issued,given or done under the said rules shall if in force at the commencementof the said rulescontinue to be in force and haveeffect as if issued,given or done under the correspondingprovisionsof these rules. (3) The provisions of these rules shall apply to any application made to the CentralGovernmentor as the casemay be the State Governmentunder the said rules for licence, registration of manufacturers, importers, dealers, repairers of weights and measurespending at the commencementof these rules and to any proceedingsconsequent thereon and to any registration granted in pursuance thereof. (4) Any legal proceeding pending in any court under the said rules at the commencementof these rulesmay be continuedin that.court as if these ruleshad not beenframed. (5) Any appeal preferred to the CentralGovernmentor as the casemay be the StateGovernmentunder the said rulesand pendingshall be deemedto havebeen madeunder the correspondingprovisionsof theserules. 58 THE GAZEITE OF INDIA: EXTRAORDINARY [PARTII-SEC. 3(iiH THE FIRST SCHEDULE (See rule 12) Supplementary Units and their symbols 1. Unit of plane angle- The unit of plain angle shall be the radian. (symbol: rad) The radian is the plane angle between two radii of a circle which cutoff, on the circumference, an arc equal in length to the radius. 2. Unit of solid-angle- The unit of solid angle shall be the steradian. {S'fIllbol: sr) The steradian is the solid angle which, having its vertex in the centre of a sphere, cuts off an area of the surface of the sphere equal to that of a square with sides of length equal to the radius of the sphere. THE SECOND SCHEDULE (See rule 13) Derived Units and Their Symbols Part I Derived Unit in relation to Space and Time 1. Unit of Area: The unit of area shall be the square metre. (Symbol: rrr) The square metre is the area of a square with sides of one metre each. 2. Unit of Volume: The unit of volume shall be the cubic metre. (Symbol: m3) I The cubic metre is the volume of a cube with sides of one metre each. 3. Unit of frequency: The unit of frequency shall be the hertz. (Symbol: Hz) The hertz is the frequency of a periodic phenomenon, the period of which is one second. IHz= 1/15. 4. Unit of angular velocity: The unit of angular velocity shall be the radian per second. (Symbol: rad/s) The radian per second ~sthe angular velocity of a body, rotating around the fixed axis, which rotates through one radian in one second, when set in uniform rotation. ['qJlj 1I-~ 3(ii)] 5. Unit of angular acceleration: The unit of angular acceleration shall be the radian per second square. (Symbol: rad/s') The radian per second squared is the angular acceleration of a body, rotating around the fixed axis, which when set in uniform varying rotation, changes angular velocity at the rate of one radian per second in one second. 6. Unit of speed and velocity: The unit of speed and velocity shall be the metre per second. (Symbol: m/s or ms') * • * • The metre per second is the velocity (speed) of a body, in motion which traverse a distance of one metre in one second when set in uniform motion. 7. Unit of acceleration: The unit of acceleration shall be the metre per second squared. (Symbol: m/s2 or rns") The metre per second squared is the acceleration of a body in motion which, when set in uniformly varying motion, changes its velocity at the rate of one metre per second in one second. 8. Unit of rotational frequency: The unit of rotational frequency shall be the second raised to the power minus one. (Symbol: s') The second raised to the power minus one is the rotational frequency of a uniform rotatory movement which produces one complete revolution in one second. 9. Unit of wave number: The unit of wave number shall be the metre raised to the power minus one. (Symbol: rn') The metre raised to the power minus one is the number of waves of a monochromatic radiation which can be accommodated, in the direction of its propagation, in a length equal to one metre. 10. Unit of vergency of optical system: The unit of vergency of optical system shall be the metre raised to the power minus one. (Symbol: rn') The metre raised to the power minus one is the vergency of an optical system,the focal distance of which is one metre in a medium having refractive index of unit. THE GAZE'fTE Of INDIA: EXTRAORDINARY IPAln II . SEC. 3(ii)1 = Note 1: This unit is also called 'per metre' or 'dioptre'. Note 2: The metre raised to the power minus one symbol mol is the unit of wave number as well as that of vergency of optical system. The context in which the said unit is used will indicate whether the unit relates to the wave number or vergency of optical system. PART II Derived Units in Relation of Mechanics 1. Unit Qf density and mass density - The unit of densitY..and mass density shall be the kilogram per cubic metre. (Symbol: kg/m3 or Kgm·3) The kilogram per cubic metre is the density or mass density of a homogenous body having a mass of one kilogram and a volume of one cubic metre. 2. Unit of concentration - The unit of concentration shall be the kilogram per cubic metre (Symbol: kg/m3 or Kgm.3) The kilogram per cubic metre is the concentration of a homogenous solution having a total volume of one cubic metre and containing a • mass of one kilogram of the given substance 3. Unit of force - The unit of force shall be the newton (Symbol: N) The newton is the force which gives to a mass of one kilogram an acceleration of one metre per second squared 1 N = 1 kg. 1m/s" 4. Unit of moment of force - The unit of moment of force shall be the newton metre. (Symbol: Nm) The newton metre is the moment of force produced in a body by a force of one newton acting at a perpendicular distance of one metre from the fixed axis around which the body turns 1 N.m = m2 kg s'L Note: The unit of moment of force shall not be written as joule (J) because it is Nm. 5. Unit of Pressure - The unit of pressure shall be the Pascal (Symbol: Pa) The Pascal is the pressure which, acting on plane surface of one square metre exerts on that area a total force of one newton 1 Pa = 1 N/m2 or 1 N m·2 6. Unit of tensile strength - The unit of tensile strength shall be Mega Pascal (Symbol: MPa or M N/m2) The tensile strength is the highest force, when applied normal to the cross-section of a test piece which it can Withstand, divided by the original area of the cross section. 7. Unit of dynamic viscosity - The unit of dynamic viscosity shall be the Pascal second. (Symbol: Pa.S) ('WT II-~ 3(ij)] 61 The Pascal second is the dynamic viscosity of a homogenous liquid in which the straight and uniform movement of a plane surface of one square metre produces a retarding force of one newton, when there is a velocity difference of one metre per second between two parallel planes separated by one metre. 1 Pa. s = 1 Pa.1m 1m/s 8. Unit of kinematic viscosity - The unit of kinematic viscosity shall be the square metre per second.(Symbol: m2/s or m2 s') The square metre per second is the kinematic viscosity of a liquid which has a dynamic viscosity of one Pascal second' arid a density of one kilogram per cubic metre. 1 m2 = 1 Pa.1s 1'S 1kg/m3 9. Unit of surface tension - The unit of surface tension shall be the newton per metre. (Symbol: N/m). The newton per metre is the surface tension produced when a force of one newton acts over a length of one metre on the surface of a liquid separating that liquid from the material surrounding it. 10. Unit of work, energy and quantify otbeet - The unit of energy, work and quantity of heat shall be the joule. (Symbol: J) The joule is the work done when the polnt of application of one newton moves a distance of one metre in the direction of the force. 1 J = 1 N.1m. 11. Unit of power, radiant flux and heat flux - The unit of power, radiant flux and heat flux shall be the watt. (Symbol: W) The watt is the power of an energy system in which one joule of energy is uniformly transferred in one second. 1W = 1 J/1s. 12. Unit of volume flow - The unit of volume flow shall be cubic metre per second. (Symbol: m3/s or m3s 1) The cubic metre per second is the volume delivered by the uniform discharge of one cubic metre traversing the given cross-section in one second. 13. Unit of mass flow - The unit of mass flow shall be the kilogram per second. (Symbol: kg/s or kg.s·1) The kilogram per second is the mass delivered by the uniform discharge of a mass of one kilogram traversing the given cross-section in one second 14 Unit of specific volume - The unit of specific volume shall be the cubic metre per kilogram. (Symbol: m3/kg) The cubic metre per kilogram is the specific volume of a homogenous body having a volume of one cubic metre and a mass of one kilogram 62 THE GAZETfE OF INDIA: EXTRAORDINARY PART III Derived Units in Relation to Heat 1. Unitof entropy- The unit of entropy shall be the joule per kelvin. (Symbol: J/K) The joule per kelvin is the increase of entropy of a system receiving a quantity of heat equal to one joule at the constant thermodynamic temperature of one kelvin, provided that no irreversible change takes place in the system. 2. Unit of specificentropy - The unit of specific entropy shall be the joule per kilogram kelvin. [Symbol: JI (kg.K)]. The joule per kilogram kelvin is the specific entropy of a system of horrfog*enousmass of one kilogram receiving a quantity -of -heat equal to one joule at the constant thermodynamic temperature of one kelvin, provided that no irreversible change takes place in the system. 3. Unit of heat capacity - The unit of heat capacity shall be the joule per kelvin. (Symbol: J/K). The joule per kelvin is the heat capacity of a homogenous body in which a quantity of heat equal to one joule produces an increase of one kelvin in the thermodynamic temperature. 4. Unit of specific heat capacity - The unit of specific heat capacity shall be the joule per kilogram kelvin. [Symbol: JI (kg.K)]. The joule per kilogram kelvin is the specific heat capacity of a homogenous body having a mass of one kilogram in which quantity of heat equal to one joule produces an increase of one kelvin in the thermodynamic temperature. 5. Unitof latent heat - The unit of latent heat shall be the joule per kilogram. (Symbol: J/kg) The joule per kilogram is the heat exchanged by one kg of substance to change from one phase to another at the temperature of its changing phase 6. Unit of specific energy - The unit of specific energy shall be the joule per kilogram. (Symbol: J/kg) The joule per kilogram is the specific energy of a system of homogenous mass of one kilogram having the internal energy of one joule. 7. Unit of thermal conductivity - The unit of thermal conductivity shall be the watt per metre kelvin. [Symbol: WI (m.K)] The watt per metre kelvin is the thermal conductivity of a homogenous body in which a difference of one kelvin in the thermodynamic temperature produces a radiant flux of one watt between two parallel planes, each having an area of one square metre, placed one metre apart. 1W/m.K = 1W/m2 1K11m ['qf1T H-l§q' 3(ii)} 8. Unit of energy densfty - The unit of energy density shall be the joule per cubic metre. (Symbol: J/m3) The joule per cubic metre is the energy density of a. system of homogenous mass of volume one cubic metre and having the radiant energy of one joule. 9. Unit of heat flux density- The unit of heat flux density shall be the watt per square metre. (Symbol: W/m2) The watt per square metre is heat flux density of a surface of one square metre in area radiating out energy at the rate of one joule per second. PART IV Derived units in relation of Electricity and Magnetism 1. Unit of quantity of electricityand electric charge - The unit of quantity of electricity and electric charge shall be the coulomb. (Symbol: C). The coulomb is the quantity of electricity carried in one second by a current of one ampere. 1C=1A.1s 2. Unit of electric chargedensity- The unit of electric charge density shall be the coulomb per cubic metre. (Symbol: C/m3) The coulomb per cubic metre is the electric charge density of a homogenous mass or system of volume one cubic metre and having a charge of one coulomb. 3. Unit of electric flux density - The unit of electric flux density shall be coulomb per square metre. (Symbol: C/m2) The coulomb per square metre is the electric flux density when a condenser, having plates of infinite area/size, parallel to each other, is charged, in vacuum, with a quantity of electricity equal to one coulomb per one square metre of area of the plates 4. Unit of electric tension, electricpotential and electromollveforce_ The unit of electric tension, electric potential and electromotive force shall be the volt. (Symbol: V). The volt is the potential difference between two points of a condUcting wire carrying a constant current of one ampere, when the power dissipated between these paints is equal to one watt. 1V=1W/1A 5. Unit of electric field strength- The unit of electric field strength shall be the volt per metre. (Symbol: VIm) The volt per metre is the electric field strength of an electric field which produces a force equal to one newton in a body charge with a quantity of electricity equal to one coulomb . .1Y = 1 N 1m 1C THE GAZEITE OF INDIA: EXTRAORDINARY [PART II-SEC. 3(i;)1 6. Unit of electricresistance- The unil of electricreslslance shall be Iheohm. (Symbol: 0) The ohm is the electric resistance between two pOints of a conductor when a constant potential difference of one volt: applied to these pOints, produces in the conductor a current of one ampere, the conductor not being the seat of any electromotive force.10 = 1V 11A. 7. Unit of conductance- The unit of conductanceshall be the siemens.(Symbol: S) The siemens is the conductance of a conductor having a resistance ofone ohm. 1S = 1 0-1 = 1_.0 8. Unit of capacitance- The unit of capacitance shall be the farad.(Symbol: F) The farad is the capacitance between the conductors of a capacitor across which there appears a potential differenc~ of one volt when it is charged by a quantity of electricity of one coulomb.1 F = 1C 11V 9 Unitofpermittivity- The unit of permittivity shall be farad per metre.(Symbol: Fzrn). The farad per metre is the permittivity of the medium which gives a capaCitance of one farad per square metre of area of two para"el prates separated by a distance of one metre. 10. Unit of inductance - The unit of inductance shall be Ihe henry(Symbol: H) The henry is the inductance of a closed circuit in which an electromotive force of one volt is produced when the electric current in the circuit varies uniformly at the rate of one ampere per second.1 H = 1V 1s 1A 11. Unit of permeability- The unit of permeabilityshall be the henry permetre. (Symbol: HIm) The henry per metre is the permeabilityof a mate"al surroundedby a single turn of nal sheet conductor inCludingan area of one square metre and length one metre which gives an inductance of one henry. 12. Unit of magnetic nux and nux of magnetic induction _ The unit of magnetic flux and flux of magnetic induction shall be the weber.(Symbol: Wb) The weber is the magnetic nux which, linking a circuil of one turn, would produce in it an electromotive force of one volt if it were reducedto zero at a uniform rate in one second. 1Wb = 1 V.1s 65 13. Unit of magnetic induction and magnetic flux density - The unit of magnetic induction and magnetic flux density shall be the tesla. (Symbol: T) The tesla is the uniform magnetic induction which, distributed evenly over a surface of one square metre, produces a total magnetic flux of one weber while passing over the surface. 1T = 1Wb/1m2 14. Unit of magnetic field strength - The unit of magnetic field strength shall be the ampere per metre. (Symbol AIm or Am01) The ampere per metre is the magnetic field strength produced in vacuum along the surface of a circular cylinder with a circumference of one metre, by a current of intensity of one ampere, maintained in a straight conductor of infinite length, of negligibl~ circular cross-section, which forms the axis of the said cylinder. 15. Unit of current density - The unit of current density shall be the ampere per square metre. (Symbol: Alm2) The ampere per square metre is the current density in a linear conductor when a current of Intensity one ampere flows uniformly through a cross-section of the conductor equal to one square metre, perpendicular to the direction of flow of the current PARTV Derived Units in Relation to Electromagnetic Radiation and Light 1. Unit of radiant intensity - The unit of radiant intensity shall be the watt per steradian. (Symbol: W/sr). The watt per steradian is the radiant intensity of a point source uniformly emitting a radiant flux of one watt within a solid angle of one steradian. 2. Unit of irradiance - The unit of irradiance shall be the watt per square metre. (Symbol: W/m2) The watt per square metre is the irradiance produced by a radiant flux of one watt, distributed uniformly over an element having a surface of one square metre. [See also (1) above] 3. Unit of radiance - The unit of radiance shall be the watt per square metre steradian. (Symbol: W/m2.sr) The watt per square metre steradian is the radiance of a source radiating one watt per steradian per square metre of projected area. 4 Unit of luminance - The unit of luminance shalf be the candela per square metre. (Symbol: cd/m2) -------------------------------------- - THE GAZETTE OF INDIA: EXIRJ\OIWINARY The candela per square metre is the luminance perpendicular to the plane surface of one square metre of a source, the luminous intensity of which perpendicular to this source is one candela, 5. Unit of luminous flux - The unit of luminous flux shall be the lumen (Symbol: 1m) The lumen is the luminous flux emitted in a solid angle of one steradian by a uniform point source having a luminous Intensity of one candela. 1 1m= 1 cd. 1 sr 6, Unit of illuminance- The unit of illuminance shall be the lux, (Symbol: Ix) ~Tae lux is the illuminance produced by a luminous flux of one lumen, uniformly distributed over a surface of area one square "metre, 1 Ix = 1 1m/1m2 PART VI Derived Unit in Relation to ionizing Radiations 1, Unit of activity (radioactivity) - The unit of activity (of a radioactive source) shall be the becqueral (Symbol:Bq) The becqueral is the activity of a radioactive source in which one transformation or one transition takes place in one second 1 8q = 1/1.s 2, Unitof absorbeddose - The unit of absorbed dose shall be gray which is equivalent to one joule per kilogram (Symbol: Gy) The gray is the dose absorbed in an element of substance of mass one kilogram to which an energy of one joule is communicated by an ionizing radiation, having a constant density of radiant flux, 1 Gy = 1 J/1 kg PART VII Derived Units in Relation to Physical Chemistry and Molecular Physics 1. Unit of concentration (of amount of substance) - The unit of concentration (of amount of substance) shall be the mole per cubic metre. (Symbol: motrrr') The mole per cubic metre is the concentration of a homogenous solution having a total volume of one cubic metre and containing one mole of the given substance, 2. Unit of molar energy - The unit of molar energy shall be the joule per mole. (Symbol: J/mol) The joule per mole is the molar energy of one mole of substance having the energy of one joule. ['IlJ1l ,,-~ 3(ii)] 67 3. Unit of molar entropy - The unit of molar entropy shall be the joule per mole kelvin. (Symbol: J/molK) The joule per mole kelvin is the molar entropy of a system of homogenous mass having a substance equal to one mole receiving a quantity of heat equal to one joule at the constant thermodynamic temperature of one kelvin provided that no irreversible change takes place in the system. 4. Unit of molar heat capacity - The unit of molar heat capacity shall be the joule per mole kelvin. (Symbol: J/mol.K) The joule per mole kelvin is the molar heat capacity of a homogenous body having an amount of substance equal to one mole, in which a ~ • quantity of heat equal to one joule produces an Jncrease of one kelvin in the thermodynamic temperature. THE THIRD SCHEDULE (See rule 14) NAMES, MAGNITUDES AND SYMBOLS OF SI PREFIXES AND PRINCIPLES OF USE OF SI PREFIXES 1. Names, Magnitudes and Symbols of SI Prefixes - The names of prefixes, their magnitudes and symbols shall be as given in Table 1 Nm fP fi TABLE 1 th . M l d d S b 1a eso re txes, elf C!IJnI u es an !f_m os Name of Prefix Magnitude of Prefix S.x_mbolof Prefix exa 10111 E ~ta 10'" p tera 10'" T giga 1011 G -j~a 10° Mkilo 103 k )- hecta 10" h J.-deca 10 da _Jdeci 10-' d Jcenti 10-': 1 c I.- Imilli 10-" m10-0--+ imicro J! !nano 10-" n ~~co 10"" _p_ 1femto 10-';) f atto 10-'0 a J Explanation: The unit of length is metre with symbol m: after adding a prefix c' for centi we get "ern" as new unit symbol. This can be raised to a positive exponent 3 to give the unit of volume. Similarly this can be combined with another unit say 'kg' and by giving it negative exponent 3 to indicate density in kg per crrr'. 68 THE GAZETTE OF INDIA: EXTRAORDINARY [PARr 1I--Sll. 3(ii)1 Kg/cm3 = kg/ 10-6m3 = 106 kg/m3 Similarly g/cm3 = 1000 kg/m3 2, Symbolhow to be combinedwith units - (a) The symbol of the prefix shalf be placed before the unit symbolwithout any intermediary spaceor dot. (b) The combination shall form the symbol of the multiple and sub­multiple of the unit 'o.'_' (c) The symbol for the prefix shall be considered to be combined with the symbol of the unit to which it is directly linked together, forming a new unit symbol, which can be combined with other unit symbols toform composite unit symbols, 3. Errors how to be avoided - To avoid errors in calculations, all quantities shall be expressed in SI units, and powers of 10 shall beused, 4. Exponents - An exponent affixed to a symbOl containing a prefix indicates that the multiple or sub-multiple of the unit is raised to the power expressed by tlie exponent. ILLUSTRATION 1 em = 10-2m gives 1 crrr' = 10-6m3 and 1 em:' = 102 rn' 5. Compoundunits how to be formed- Only one prefix shall be used in forming the multiples of a compound unit, and compound prefixes shallnot be used. ILLUSTRA TlON Write nm (nano metre), instead of mum. 6. Use of prefixes with unit mass - Notwithstanding that the base unit of mass contains a prefix, names of deCimal multiples or sub-multiples of the unit of mass shall be formed by attaching prefixes to the wordgram ILLUSTRATION Write milligram (mg) but not micro kilogram (j.Jkg) 7. Printing:(1) Symbols of units _ (a) Shall be printed in roman (upright) type irrespective of the type usedin the rest of the text; (b) Shall remain unaltered in the plural; (c) Shall be written, without a final full stop (periOd) unless the contextotherwise requires; and (d) shall be placed after the comp~etenumerical value in the expression for a quantity, leaving a space between the numerical value and theunit. (2) The symbol for units of weight or measure shall be printed in lower case letters except that the first letter shall be printed in Upper case when the name of the unit is derived from a proper name ['WT Il-~ 3(ii)] ILLUSTRATION m - metre s - second A - Ampere Wb - weber 8. Multiplication of units - (1) When a compound unit is formed by multiplication of two or more units, the multiplication may be indicated in one of the following ways: m. N, Nrn, Nm (2) In using a symbol of a unit of weight or measure which coincides with the symbol for a prefix, special care shall be~ta.ken to avoid confusion. ILLUSTRATION The unit 'newton metre' shall be written Nm or rn.N to avoid confusion with mN, the millinewton. 9. Division of Units - (1). When a compound is formed by divIding one unit by another the division shall be indicated in one of the following ways: - m/s or by writing the product of m and S·1 as ms' (2) The letter p shall not be used to denote division. ILLUSTRA TION Do not write kmph, write km/h or km.h' (3) In no case shall more than one solidus (oblique stroke) on the same line be included in such a combination unless a parenthesis is inserted to avoid ambiguity: ILLUSTRATION Write m/s2 or rn.s" but not m/s/sl (4) In complicated cases, negative powers or parenthesis shall be used. ILLUSTRATION Write m.kg/(s3.A) or m.kg.s·3A1 but not m.kg/s3A 10. Expression of results - (1) The appropriate integral multiple and sub­ multiple to which a unit is to be expressed shall be selected in such a manner that the numerical value to be expressed is between 0.1 and 1000 ILLUSTRA TlON 1.2 x 104Nmay be written as 12 kN 000394 m may be written as 3.94 mm 1 40 1 Pa may be written as 1401 kPa 3.1 x 1O.8smay be written as 31 ns (2) In a table of values for the same quantity or in a discussion of such values within a given context the same integral multiple or sub-multiple of a unit may be used for all items, even when some of the numerical values may be outside the range of 0 1 to 1000 (3) For the purpose of expression of dimensions in mechanical engineering drawings only the millimetre .shall be used. 70 THE GAZETTE OF INDIA: EXTRAORDINARY 4, IPAin II--SI(, 3(ii)111. Expression of Numbers _ (1) To express numbers in connection with units of weights and measures, the dot shall be used to separate the integral part of numbers from the decimal part, (2) Numbers shall be divided in groups of three starting from the decimal point in order to faCilitate regarding and neither dots nor commas shall be inserted in the space between such group ofnumbers, ILLUSTRA TION Write 3211 468,02282 Not 3,211.468,022,82 or 3,211,468,022,82 = THE FOURTH SCHEDULi • (See rule 15) Units Permitted to be used with base, Supplementary or Derived Units 1 Permitted units of time - (1) The permitted units in relation to time shallbe as follows, namely: _ ' (i) the minute, equal to 60 second (Symbol: min), (ii) the hour, equal to 3600 seconds or 60 minutes (Symbol: h), and (iii) the day, equal to 86,000 seconds or 24 hours (Symbol: d) The week, month and year shall correspond to the saka Calendar orthe Gregonan calendar, 2, Permitted units of plane angle - The permitted units in relation to plane angle shall be as follows, namely: _ (i) The degree, equal t

Previous and next

All provisions of Legal Metrology National Standards Rules, 2011

Questions people ask

Is rule 33 of Legal Metrology National Standards Rules, 2011 still in force?

No repeal of Legal Metrology National Standards Rules, 2011 is recorded.