LawGrids logoLAWGRIDS.ORG

Rule 5, Central Motor Vehicles (2nd Amendment) Rules, 2009.: The

Central Motor Vehicles (2nd Amendment) Rules, 2009. - Rule 5

Text of rule 5

The

5. The. -smoke opacity is to be determined on the Engine Load Response (ELR) test as specified in Part XII of MoSRTH/CMVR/TAP-115/116 as amended from time to time. 6. In case of vehicles operating on CNG or LPG mode, the provisions of rules 115-8 and 115-C shall be applicable respectively. 7. The reference fuel shall be as specified in Annexure IV K for Diesel vehicles, Annexure IV L for CNG (G20, G23 and G25) vehicles and Annexure IV M for LPG (Fuel A and Fuel 8) vehicles respectively. Reference Fuel as per · Annexure IV L and IV M shall be used for Type Approval and Conformity of Production, one year after the same is available to the test agencies. Till then, Commercial CNG I LPG fuel shall be used. 8. The Conformity of Production (COP) testing procedure shall be as specified in MoSRTH/CMVR/T AP-115/116 as amended from time to time. 9. The Conformity of Production (COP) frequency and samples: (i) The Conformity of Production period for each engine model including its variant (s) shall be once a year; (ii) Where production volume in six months is less than 250 per model including it's variants, the provisions contained in the provisos to rule 126-A shall apply. 10. For diesel engine vehicles, the emission of visible pollutants (smoke) shall not exceed the limit value of smoke density, as per Annexure I to sub-rule (9) of rule 115. These smoke limits are without correction factor and engines are to be tested with conditioned air supplied to the engine to maintain atmospheric factor of 0.98 to 1.02. 11. The commercial Diesel fuel shall be as per Annexure IV-0 in respect of the places mentioned in sub-clause (i) of clause (a) of this sub-rule and in respect of all other places, the commercial fuel shall be as per BIS specification 36 lHEGAZETIE OF INDIA: EXTRAORDINARY [PARTIl-SEC. 3(i)] IS:1460-2005 (fifth revision) for Diesel. Specification for Commercial CNG and LPG shall be as notified from time to time. 12. For vehicles with Gross Vehicle Weight exceeding 3,500 kg manufactured on or after the 111April, 2010, - (i) deterioration factor shall be as given in the Table below: Engine type Test c cle Diesel engine ESC ETC CNG, LPG or ETC Gaseous fuelled en ine co HC NMHC CH4 NOx PM 1.1 1.05 - - 1.05 1.1 · 1.1 1.05 - - 1.05 1.1 1.1 1.05 1.05 1.2 1.05 - I I . I ii) alternatively, the vehicle manufacturers may opt for evaluation of deterioration factor as specified in MoSRTH/CMVR/T AP-115/116 as amended from time to time. Category of Vehicle in which engine will Minimum Service be installed accumulation period Cateoorv N1 Vehicles 100,000 km cateacrv N2 Vehicles 125,000 km Category N3 Vehicles with GVW equal to 125,000 km or less than 16,000 ko Category N3 Vehicles with GVW above 167,000 km 16,000 kg Cateaorv M2 Vehicles 100,000 km Category M3 Vehicles with GVW equal to 125,000 km or less than 7,500 ka Category M3 Vehicles with GVW above 167,000 km 7,500 kg The above ageing test should be carried out by the approval test agency. 13. In the case of Diesel vehicles, the engine power shall be measured on engine dynamometer and the measured power shall not differ from the specified power as given in Chapter - 1 of Part IV of MoSRTH/CMVR/T AP - 115/116 as amended from time to time when tested as per procedures laid down in Chapter - 6 of Part IV of MoSRTH/CMVR/T AP - 115/116 as amended from time to time. 14. (i) The CNG and LPG vehicles specified in this sub-clause shall comply with the provisions of clause (i) of sub-rule (2) of rule 115 (ii) All Diesel Fuelled .Vehicles specified in this sub-clause shall comply with the provisions of clause (ii) of sub-rule (2) of rule 115. 15. The extension of type approval to engine family and engine after treatment system family shall be as described in MoSRTH/CMVR/TAP- 115/116 as amended from time to time. 16. ... The vehicles specifi'd in this sub-clause shall be equipped with an On­ Board Diagnostic s?stems for e?nission control which shall have the capability of identifying the likely orea of malfunction by means of fault codes stored in computer memory f')r vehicle manufactured on and from 111April 2013, as ?r procedure. laid down in MoSRTH/CMVR/TAP- 115/116 and as amended from time to ume. 17. The Diesel engine NOx reducncn agent AUS 32 (Aqueous Urea Solution) shall conform to Part 1 and Part 2 of ISO 22241-2006:. 3. In the said rules, in rule 115A. after sub-rule (6), the following sub-rule shall be inserted, namely: - •(7) Every diesel driven agricultural tractor manufactured on and from the date specified in column (2) of the Table 1 shall comply with the Bharat (Trem) Stage-Ill A norms and the weighted average mass of Carbon Monoxide (CO), Hydrocarbon (HC) and Oxides of Nitrogen (NOx) and Particulate Matters (PM) in grams per kilo Watt/hour emitted by them in addition to those of visible pollutants as provided in sub-rule (2), when tested for Type Approval (TA) and Conformity of Production (COP) in accordance with the procedure specified in ISO 8178 Part-4 (1996) 'C1' 8 mode cycle, shall not exceed the limits given in columns (3), (4) and (5) respectively, of the said Table. Table 1 Limit Values for Type Approval (TA) and Conformity of Production (COP) Category Applicable co HC+ NOx PM from {1) {2) (3) (4) {5) <8kW 1.4.2010 5.5 8.5 0.8 8 <= kW< 19 1.4.2010 5.5 8.5 0.8 19<= kW< 37 1.4.2010 5.5 7.5 0.6 37 <= kW< 56 1.4.2011 5.0 4.7 0.4 56<= kW< 75 1.4.2011 5.0 4.7 0.4 75<=kW<130 1.4.2011 5.0 4.0 0.3 130<= kW < 560 1.4.2011 3.5 4.0 0.2 Notes:- 1. The test shall be on Engine Dynamometer. Table 3 Table 2 , fPARTII-Soc.3(i)]TIIEGAZETIE OFINDIA: ?RDINARY Category (power band) Useful life (hours) (Emission Durability Period) <=19 kW 3000 19< kW <=37 5000 - >37kW 8000 3. The test procedure for measurement of emission of visible and gaseous pollutants and Particulate Matter shall be as per MoSRTH/CMVRIT AP-115/116 Part X (Sub­ part A). Explanation 1. - The term "engine family" includes a range of engines having similar design parameters for emission levels. 2. The test procedure for measurement of Gross Power (without Fan) sha.11be as per Part IV of MoSRTH/CMVRIT AP-115/116 Issue No.3. 4. Test fuel shall be the reference fuel as specified in Annexure-.IV P 5. The emission of visible pollutants, when tested as provided in sub-rule (3) of rule . 115-A, shall not exceed the limit values given ther?in. 6. To meet Bharat (Trem) Stage-Ill A norms with effect from t:,e date specified in ct:?i.imn (2) of Table 1, the engine manufacturer may opt for an aging test as 5pecified in Table 2 for evaluating deterioration factors as per Annexure V of Part X (Sub-part-8) of MoSRTH/CMVR/T AP/115-116 Issue No.3 or fixed deterioration factors as per Table 3. 7. There shall be no relaxation of norms for Conformity of Production (COP} purposes. 8. Conformity of Production (COP} Selection Procedure shall be as per MoSRTH/CMVRIT AP-115/116 Part V!. 9. Conformity of Production (COP) Frequency shall be as per Part X (Sub-part A) of MoSRTH/CMVR/T AP-115/116. 10. The extension of Type Approval (TA} to engine family and engine after- treatment system family shall be specified in MoSRTH/CMVR/T AP-115/116 as amended from time to time. 38 39 Explanation 2. - The term Mangineafter-treatment system family" means if same after-treatment system consisting of catalyst, particulate traps etc., is used on a series of engines, then the deterioration factor based on one engine test shall be applicable to the entire series." . . 4. In the said rules. in rule 115 B,­ (1) in item A, - (a) in sub-item (I), for clauses (c), (d) and (e), the following clauses shall be- substituted, namely:- "(c) vehicle models and variants having option for bi-fuel operation and fitted with limp-home Gasoline tank of capacity not exceeding two litres, three litres and five litres respectively on two-w!i?eler, three-wheeler and four-wheeler shall be exempted from mass amission tests including all tests specified under sub-rule {2), i•,otes 6 and 7 mentioned below clause (C) of sub-rule (14) i:tnd Notes 6, 7, 15 and 16 of sub-clause (i) of clause (b) of stt!J-rule .. (15) of rule 115 in Gasoline mode; (d) prevalent conformity of production procedure shall also be applicable.·: (b) in sub-item (II), in clause (a), after sub-clause (iii), the following sub­ clause shall be inserted, namely:- "(iv) for the vehicles manufactured on and after the 1st day of April 2010, the type approval norms as applicable, subject to minimum of Bharat Stage- IV emission norms for Category PJIand Category N Vehicles with Gross Vehicle Weight not exceeding 3,500 kg and Bharat Stage-Ill emission norms for two and three wheelers."; (c) in the Explanation, in clause (a), in the Table, for serial number (iii) and the entries relating thereto, the following serial number and entries shall be substituted, namely:- (1) (2) M(iii)Fuel s. No. 31 of the notification Consumption number S.0.1365 (E), dated the test 13th December 2004"· (2) in item B,- (a) in sub-item (II), in clause (c), after sub-clause (iii), the following sub-clause shall be inserted, namely:- "(iv)for the vehicles manufactured on and after 1st April 2010, the type approval norms as apphcable, shall be subject to minimum of Bharat Stage- IV emission norms in case of four wheelers and Bharat Stage- rnEGAZETTE OF INDIA: EXIRAORDINARY • (PAJtrII-SEC. 3(i)] Ill emission norms in case of two and three wheelers till the validity of these norms": (b) in the Explanation, in clause (a), in the table, for serial number (iv) and the entries relating thereto, the following serial number and entries shall be substituted, namely:- (1) - (2) ·(iv) Fuel Consumption test S. No. 31 of the notification number s.o. 1365 (E), dated· the 13th - December, 2004•; (3) in item C, in the table, for seria! , ,umber (vii)and the entries relating thereto, the following serial number an?. snmes shall be substituted, namely:- (1) (2) "(vii)Fuel S. No. 31 of the notification number S.0. Consumption test 1365 (E), dated the 13th December, 2004"; (4) for item D, the following item shall be substituted, namely: "D. Applicable Emission Norms Cateaorv Applicable Emission Norms (i) OE CNG Category M and Prevailing gasoline norms Category N Vehicles with GWJ equal to or less than 3,500 kg, Three wheelers and Two wheelers. ? (ii) CNG Category M and Prevailing gasoline norms Category N vehicles . with GVVv equal to or less than 3,500 kg, Three and Two wheelers retro fitment from gasoline vehicles. . (iii) CNG Category M and Prevailing diesel norms Category N vehicles with GWJ equal to or less than 3,500 kg, Three and Two wheelers retro fitment from diesel vehicles. 41 I (iv) CNG engines Category M Prevailing diesel engine norms and Category N vehicles with GWv based on 13-mode steady-state greater than 3,500 kg manufactured engine dynamometer test or 13- upto 1st April 2010. mode Engine Steady State Cycle as applicable. (v) CNG engines for Category Prevailing diesel engine emission M and Category N vehicles with nor-ns.". GWv greater than 3,500 kg manufactured on and from 1st April 2010 5. In the said rules, in rule 115 C,- (A) in sub-rule (2).- (i) for clause (a), the following clause shall be substituted, namely:- "(a) in case of LPG fitments done by vehicle manufacturers on new gasoline vehicles, each model manufactured by vehicle manufacturers shall be type approved as per the prevailing mass emission norms as applicable for the category of new vehicles in respect of the place of its use."; (ii) for clauses (c), (d) and (e) the following clauses shall be substituted, namely:- "(c) vehicle models and variants having option for bi­ fuel operation and fitted with limp-home Gasoline tank of capacity not exceeding two litres, three litres and five litres respectively ontwo-wheeler, three-wheeler and four-wheeler shall be exempted from mass emission tests including all tests specified under sub-rule (2), Notes 6 and 7 mentioned below clause (C) of sub-rule (14) and Notes 6, 7, 15 and 16 of sub-clause (i) of clause (b) of sub-rule (15) of rule 115 in Gasoline mode; (d) prevalent conformity of production procedure shall also be appflcable.": (B) in sub-rule (3),- (i) in clause (a), after sub-clause (iii), the following sub-clause shall be inserted, namely:- 42 TIIEGAZETIE OF INDIA: EXlRAORDINARY [PAR:Il-SEC.3(i)] "(iv) for the vehicles manufactured on and after the 1st day of April 2010, the type approval norms as applicable, subject to minimum of Bharat Stage- IV emission norms for Category M and Category N Vehicles with Gross Vehicle Weight not exceeding 3,500 kg and Bharat Stage- Ill emission norms for two and three wheelers."; (ii) in clause (b}, for sub-clause (ii), the t,1llowing sub-clause shall be substituted, namely:- "(ii) separate type approval shall be .iecessary for the following types of vehicles - (a) two stroke (b) four stroke (c) carbureted (d) single point fuel inje:cted; and (e) multi point fuel injected."; (C) in sub-rule (6), in the Explanation, in clause (a). in the table, for SI. No. 4 and the entries relating thereto, the following SI. No. and entries shall be substituted, namely:- (1) (2) (3) "4. Fuel Consumption test 5. No. 31 of the nouficaiion number S.O. 1365 (E), dated the 13th December. 2004"; (D) in sub-rule (7), in the table, for SI. No. 4 and the entries relating thereto, the following SI. No. and entries shall be substituted, namely:- (1) (2) (3) "4. Fuel Consumption test S. No. 31 of the notification number S.O. 1365 (E), dated t,,e 'i 3th December, 2004"; (E) in sub-rule (8), for the table, the following table shall be substituted, namely:- · Category Applicable Emission Norms (i) OE LPG Category M and Prevailing gasoline norms Category N Vehicles with GVW equal to or less than 3,500 kg, Three wheelers and Two wheelers. •, (ii) LPG Category M and Prevailing gasoline norms Category N vehicles with GVW · equal to or less than s.soo k9. Three and Two wheelers retro fitment from gasoline vehicles. .. 43 . (iii) LPG Category M and Catego, y N vehicles with GVW equal to or less than 3,500 kg, Three .and Two wheelers retro fitment from diesel vehicles. Prevailing diesel norms Prevailing diesel engine norms based on 13-mode steady­ state engine dynamometer test or 13-mode Engine Steady State Cvcle as aoolicable. (iv) LPG .e:.lgines Category M and Ca?egory N vehicles with GVW oreater than 3,500 kg manufactured · upto 1st April 2010. · (v) LPG engines for Category Prevailing diesel M and Category N vehicles emission norms.". with GVW greater than 3,500 kg manufactured on and from 1st Aoril 201 O engine . , 6. In the said rules, in rule 126, after the words "the lntematior.al Centre for Automotive Technology, Manesar", the words "or the Northern Region Farm Machinery Training and Testing Institute, Hissar (for testing of combine harvester)" shall be substituted. 7. In the said rules, after Annexure IV-I, the following Annexures shall be inserted, namely:- 536 Gl/09-7 TIIEGAZE1TE OF INDIA· EX'IRAORDINARY [PARTII-Soc. 3(i)] .. "ANNEXURE ..: N J · [See rule 115(15)] Technical Specification of the Reference Fuel to be used for testing vehicles equipped ·tt, Ga II IWI so ne eng nes. Parameter Unit Limits <1> Test MethodMinimum Maximum I Research octane number, RON 95.0 -- EN 25164 Motor octane number, MON 85.0 - EN 25163 Density at 15 degrees C l<g/m3 740 754 ISO 3675 Reid vapour pressure ?Pa 56.0 60.0 PrEN ISO; 13016-1; (DVPE) Dlstlllation : -evaporated at 70 degress C ?v/v 24.0 40.0 EN-ISO 3405 -evaporated at 100 degrees C %v/v. 50.0 58.0 EN-ISO 3405 -evaporated at 150 degrees C %v/v 83.0 89.0 EN-ISO 3405 -final bollingpoint ?ree: 190 210 EN-ISO 3405 Residue %v/v - 2.0 EN-ISO 3405 Hvdrocarbon analysis: -olefins ?v/v - 10.0 ASTM D 1319 -aromatics 1%v/v 29.0 35.0 ASTM D 1319 -benzene %v/v - 1.0 ASTM D 1319 -saturates % v/v Report Report Pr. EN 12177 Carbon I Hydrogen ratio Report ASTM D 1319 Induction period (2) minutes 480 - EN-ISO 7536 Oxygen content ?m/m - 1.0 EN 1601 Existent gum ?/ml - 0.04 EN-ISO 6246 Sulphur content (3) r,g/kg - 10 ASTM D 5453 Copper corrosion - Class 1 EN-ISO 2160- Lead content mg/I - 5 EN 237 Phosphorus content mg/I - 1.3 ASTM D 3231 111Thevalues quoted In the spedflcatlons are "true values". In establishment of their limit values the terms of ISC4259 Petroleum products - Determination and application of precision data In relation to methods of test have beenapplied and In fixing a minimum value, a minimum dltfenence of 2R above zero has been taken lnto account; In fixinga maximum and minimum value, the minimum difference Is 4R (R=reproduclbility).Notwithstandingthis measune,which is necessary for technical reasons, the manufacturer of fuels should nevertheless aim at a zero value wherEthe stipulated maximum value Is 2R and at the mean value In the case of quotations of maximum and minlmurrlimits. Should It be necessary to clarify the questions as to whether a fuel meets the requirements of thEspecifications,the terms of ISO 4259 should be applied. <2>Thefuel may contain oxidation Inhibitors and metal deactivators normally used to stabilize refinery gasolinestreams, but detergent/dispersive additives and solvent oils must not be added. <3> The actual sulphur content of the fuel used for the Type I test shall be reoorted 45 • • • • •.

Previous and next

All provisions of Central Motor Vehicles (2nd Amendment) Rules, 2009.

Questions people ask

Is rule 5 of Central Motor Vehicles (2nd Amendment) Rules, 2009. still in force?

No repeal of Central Motor Vehicles (2nd Amendment) Rules, 2009. is recorded.