LawGrids logoLAWGRIDS.ORG

Rule 139, The Explosives Rules, 2008: Repeal and Savings

The Explosives Rules, 2008 - Rule 139

Text of rule 139

Repeal and Savings

139. Repeal and Savings.—(1) The Explosives Rules, 1983 are hereby repealed. (2) Notwithstanding such repeal— (a) all licences, permits or duplicates thereof granted or renewed under the said rules and all fees imposed or levied shall be deemed to have been granted, renewed, imposed or levied, as the case may be, under the corresponding provisions of these rules; (b) all approvals given and all powers conferred by or under any notification or rule shall, so far as they are consistent with the Act and these rules, be deemed to have been given or conferred by under this Act or these rules. SCHEDULE— I Part—1 Classification of explosives (see rule 4) Explosives are divided into 8 classes as follows : Class 1 Gunpowder Class Class 2 Nitrate-Mixture Class Class 3 Nitro-Compound Class Class 4 Chlorate-Mixture Class Class 5 Fulminate Class Class 6 Ammunition Class 204 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Class 7 Fireworks Class Class 8 Liquid Oxygen Explosives Class. Class 1—Gunpowder Class “Gunpowder” means gunpowder ordinarily so called. Class 2—Nitrate Mixture Class "Nitrate-mixture" means any preparation, other than gunpowder which is formed by the mechanical mixture of a nitrate with any form of carbon or with any carbonaceous substance not possessed of explosives properties, whether sulphur be or be not added to such preparation, and whether such preparation be or be not mechanically mixed with any other non-explosive substance, and includes any explosive containing as per chlorate and not being a chlorate-mixture, fulminate or nitro-compound as defined in this Schedule Class 3- Nitro-Compound Class (1) "Nitro-compound" means any chemical compound which is possessed of explosive properties or is capable of combining with metals to form an explosive compound, and is produced by the chemical action of nitric acid (whether mixed or not, with sulphuric acid), or of a nitrate mixed with sulphuric acid, upon any carbonaceous substance, whether such compound is mechanically mixed with other substances or not. (2) The nitro-compound class two divisions namely division 1 and division 2. (3) Division 1, comprising any chemical compound or mechanically mixed preparation which consists, either wholly or partly, of nitro-glycerine or some other liquid nitro-compound. (4) Division 2 comprising any nitro-compound, which is not comprised in Division 1 that is explosives such as Tri-nitro-toluene (T.N.T.) etc. Class 4-Chlorate mixture Class (1) "Chlorate-mixture" means any explosive containing a chlorate. (2) Chlorate-mixture class has 2 divisions namely Division 1 and Division 2. (3) Division 1, comprising any chlorate preparation which consists partly of nitro-glycerine or of some other liquid nitro-compound. (4) Division 2, comprising any chlorate mixture which is not comprised in Division 1. Class 5 -Fulminate Class (1) "Fulminate" means any chemical compound or mechanical mixture whatever, which from its great susceptibility to detonation, is suitable for employment in percussion-caps or any other appliances for developing detonation, or which, from its extreme sensibility to explosion, and from its great instability (that is to say, readiness to undergo decomposition from very slight exciting causes), is specially dangerous. (2) The Fulminate class consists of two divisions namely division 1 and division 2. (3) Division 1 comprising such compounds as the Fulminate of sliver and of mercury, and preparations of those substances such as are used in percussion caps, and any preparation consisting of a mixture of chlorate with phosphorus, or certain descriptions of compounds of phosphorous, with or without the addition of carbonaceous matter, and any preparation consisting of a mixture of a chlorate with sulphur or with sulphuret, with or without carbonaceous matter. (4) Division 2 comprises such substances as the chloride and the Iodide of Nitrogen, Fulminating Gold and Silver, Diazobenzol and the Nitrate of Diazobenzol, Lead Azide and Tetrazine. Class 6-Ammunition Class (1) “Ammunition" means an explosive of any of the foregoing classes when the same is enclosed in any case or contrivance, or is otherwise adapted or prepared so as to form: (a) a cartridge or charge for small arms, cannon or any other weapon, or (b) a safety or other fuse for blasting or for shells, or (c) a tube for firing explosive, or (d) a percussion cap, detonator, fog signal, shell, torpedo, war rocket or any other contrivance other than a firework. (2) The ammunition class has three divisions, namely Division 1, Division 2 and Division 3. (3) Division 1 comprises exclusively of (i) Safety cartridges (ii) Safety fuses for blasting (iii) Railway fog signal and (iv) Percussion caps. (4) Division 2 comprises any ammunition, which does not contain its own means of ignition and is not included in Division 1, such as cartridges for small arms other than safety cartridge, cartridges and charges for cannon shells and torpedoes containing any explosives, tubes for firing explosives, and war rocket, which do not contain their own means of ignition. (5) Division 3 comprises any ammunition which contains its own means of ignition and is not included in Division 1, such as detonators, fuses for blasting which are not safety fuses, tubes for firing explosives, containing their own means of ignition. Note: The expression "ammunition containing its own means of ignition" means ammunition having an arrangement, whether attached to or forming part of the ammunition which is adapted to explode or fire the ammunition by friction or percussion. "Percussion cap" does not include a detonator. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 205 Class 7-Fireworks Class (1) Fireworks Class has four divisions, namely, Division 1, Division 2, Division 3, and Division 4. (2) Division 1 comprises fireworks composition that is to say, any chemical compound or mechanically mixed preparation of an explosive or inflammable nature, which is used for the purpose of making manufactured firework, and is not an explosive of classes 1,2,3,4,5 & 6, any star and any coloured fire composition: Provided that a substantially constructed hermetically closed metal case, containing not more than 500 grammes of coloured fire composition of such a nature, as not to be liable to spontaneous ignition shall be deemed to be "a manufactured firework" and not a "firework composition". (3) Division 2 fireworks comprises manufactured fireworks i.e. to say any explosive of class 1,2,3,4 or 6 and any fireworks composition when such explosive or composition is enclosed in any case or contrivance or other articles specially adapted, for the production of pyrotechnic effect for pyrotechnic signal or sound signals. (4) Division 2 fireworks comprises 3 sub-divisions, namely, Sub-division 1, Sub-division 2 and Sub-division 3. (5) Sub-division 1 of Division 2 fireworks comprises low hazard fireworks which, in the opinion of Chief Controller are relatively innocuous in themselves and are not liable to explode violently or all at once e.g. sparklers [Chinese crackers, serpents, etc.] (6) Sub-division 2 of Division 2 of fireworks comprises high hazard fireworks which, in the opinion of Chief Controller, present a special hazard to a person e.g. rockets, shells, maroons, wheels, barrages, fountains, illumination pieces, distress signals, pyrotechnic devices etc. (7) Sub-division 3 of Division 2 fireworks comprises such fireworks, which are assembled at site purely for the purpose of display. (8) Division 3 comprises any explosive contrivance required for the manufacture of manufactured fireworks e.g. quick match fuse, micro cord fuse etc. (9) Division 4 comprises manufactured fireworks for use of Armed Forces of the Union. Class 8-Liquid Oxygen Explosives Class "Liquid Oxygen Explosives" means an absorbent carbonaceous material such as wood pulp. carbon black, metal powder, coal dust etc. impregnated with liquid air or liquid oxygen with or without the addition of other substances. Part —2 UN Classification of Explosives As per the United Nations recommendations in the Model Regulation on the Transport of Dangerous Goods published vide ST/SG/AL.10/1/ Rev 12 in ISBN 92 -1-13974-5, the U N Classification of dangerous goods have been made as U N Class 1(Explosives), Class 2 (Gases), Class 3 (Flammable liquid), Class 4 (Flammable Solids; substances liable to spontaneous combustion; and substances which in contact with water emit flammable gases ), Class 5 ( Oxidizing substances; organic peroxides ), Class 6 (Poisonous and infectious substances), Class 7 (Radioactive Materials), Class 8 (Corrosive substances) and class 9 (Miscellaneous dangerous substances). Therefore explosives, which come within the purview of the Explosives Rules, are hazardous goods of UN Class 1. The UN Class 1 i.e. explosives, have been further divided into 6 divisions as follows: Division 1.1 (U N Class 1 Division 1): Substances and articles which have a mass explosion hazard e.g., Gun powder, class 3 explosives, Detonators (ordinary or electric), Detonating fuse, shaped charge, demolition charge, boosters, tetryl, smoke less powder, fireworks composition etc. Division 1.2 (U N Class 1 Division 2): Substances and articles, which have a projection, hazard but not a mass explosion hazard. Division 1.3 (U N Class 1 Division 3): Substances and articles, which have a fire hazard and either a minor blast hazard or a minor projection hazard or both but not, a mass explosion hazard. Division 1.4 (U N Class 1 Division 4): Substances and articles, which present no significant hazard, e.g., practice grenades, Safety fuse, fireworks, 206 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Division 1.5 (U N Class 1 Division 5): Very insensitive substances, which have a mass explosion, hazard e.g., non- cap sensitive class 2 explosives. Division 1.6 (U N Class 1 Division 6): Extremely insensitive articles, which do not have a mass explosion hazard. Notes: (1) For the purpose of safety distances as applicable for manufacturing factories and magazines, (a) Explosives of "X" category (except sparklers) can be considered as explosives belonging to U N Class 1.4; (b) Explosives of "Y" category as explosives of U N Class 1.3; (c) Explosives of "ZZ" category as explosives of U N Class 1.1 and 1.5; (2) For very low hazard fireworks like sparklers, separate Tables of Safety distances have been prescribed for manufacturing or storage purpose. Part - 3 Table - 1 Compatibility Groups Pertaining to UN Classification of Explosives: - The Compatibility Group pertaining to U N Classification Codes of hazardous goods for the purpose of packaging for transport, import and export shall be as follows: Serial No. Compatibility Group Description of substance or article to be classified 1 A Primary explosive substance 2 B Article containing a primary explosive and not containing two or more independent safety features 3 C Propellant explosive substance or other deflagrating explosive substance or article containing such explosive substance 4 D Secondary detonating explosive substance or black powder or article containing a secondary detonating explosive substance, in each case without means of initiation and without a propelling charge, or article containing a primary explosive substance and containing two or more independent safety features 5 E Article containing a secondary detonating explosive substance, without means of initiation with a propelling charge (other than one containing an inflammable or hypergolic liquid) 6 F Article containing a secondary detonating explosive substance, without means of initiation, with a propelling charge (other than one containing an inflammable or hypergolic liquid) or without a propelling charge 7 G Pyrotechnic substance or article containing a pyrotechnic substance or article containing both an explosive substance and an illuminating, incendiary lachrymatory or smoke-producing substance (other than a water-activated article or one containing white phosphorus, phosphide or inflammable liquid or gel) 8 H Article containing both an explosive substance and white phosphorus 9 J Article containing both an explosive substance and an inflammable liquid or gel 10 K Article containing both an explosive substance and a toxic chemical agent 11 L Explosive substance or article containing an explosive substance and presenting a special risk needing isolation or each type 12 S Substance or article so packed or designed that any hazardous effects arising from accidental functioning are confirmed within the package unless the package has been degraded by fire, in which case all blast or projection effects are limited to the extent that they do not significantly hinder or prohibit fire-fighting or other emergency response efforts in the immediate vicinity of the package. Note: As per the Explosives Rules, the methods of packaging of explosives for transport within India may be as per Part -1 of Schedule 2 but the methods of packaging of explosives for import and export of explosives shall be as per Part -2 of Schedule 2 ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 207 Table - 2 Scheme of classification of goods of class 1 Compatibility Group A B C D E F G H J K L S Hazard Division 1.1 1.1 A 1.1B 1.1C 1.1 D 1.1 E 1.1F 1.1G 1.1 J 1.1 L 1.2 1.2B 1.2C 1.2D 1.2E 1.2F 1.2G 1.2H 1.2J 1.2K 1.2L 1.3 1.3C 1.3F 1.3G 1.3H 1.3J 1.3K 1.3L 1.4 1.4B 1.4C 1.4D 1.4E 1.4F 1.4G 1.4S 1.5 1.5D Table - 3 Compatibility Group A B C D E G S A Yes No No No No No No B No Yes No* No* No* No* Yes C No No* Yes Yes Yes No Yes D No No* Yes Yes Yes No Yes E No No* Yes Yes Yes No Yes G No No No No No No Yes S No Yes Yes Yes Yes Yes Yes Schedule II Part-1 Methods of packing of explosives for inland transport. (See rules 14 and 15) (1) In this Schedule, unless the context otherwise requires, the expression,- (a) "outer package" means a box, barrel, case or cylinder of wood, metal, or corrugated boxes or other solid material, of such strength, construction and character as not to be liable to be broken or accidentally opened, or to become defective or insecure or to allow an explosive to escape; (b) "inner package" means a substantial case, bag, canister, card board or other receptacle, made and closed so as to prevent any explosive from escaping; (c) "propellant" means an authorised explosive of the class 3 adapted and intended exclusively for use as a propelling charge in cannon or small arms . (2) Wherever an explosive is distinguished as belonging to a particular class or division of a class, the reference is to be made to the classification specified in Schedule 1; (3) The packages of explosives shall conform to the requirements of relevant standards of Bureau of Indian Standards. 208 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] TABLE Item Class Method of packing Quantity in any one Quantity in any No. outer package one inner package (1) (2) (3) (4) (5) 1 Class 1 When the quantity in any one consignment does not exceed 2.5 kilogrammes , a single outer package. When the quantity exceeds 2.5 kilogrammes a 50 kilogrammes double package, the inner and outer packages being Provided that where gun- as defined in clause (1) of this Schedule. Inner powder and propellants Packages if made of metal shall be secured by are packed together the 2.5 kilogrammes cushioning material. amount shall not exceed 25 Kilogrammes 2 Class 2 The material except site mixed Ammonium Nitrate 25 Kilogrammes 12.5 Kilogrammes Fuel Oil explosive shall be suitably cartridged in wrappings made of suitable plastic material or papers so as to make it impermeable and protect from damp. Further packing as for Class 1. 3 Site Mixed As approved by Chief Controller Ammonium Nitrate Fuel Oil mixture (ANFO) 4 Class 3 The material shall be cartridged in wrappings made 25 Kilogrammes 2.5 Kilogrammes Division 1 of paper or polythene that has been made other than impermeable. The wrapping should also protect the propellants material from damp. Further packing as for Class 1, provided that either the outer or inner package shall be thoroughly waterproof and no metal shall be used in the construction of the packages, except that (1) nails made of brass, zinc or other soft metal or coated with the same may be used for securing the outer pac- kage, and (2) wire stitching may be used for securing the inner package if the wire is effectively prevented from coming into contact with the explosive by means of a sheet of stout cardboard or otherwise. 5. Class 3 As for Class 1 25 Kilogrammes 2.5 Kilogrammes Division 1 propellants. 6 Class 3 As for Class 1 25 Kilogrammes 2.5 Kilogrammes Division 2 Other than Picric Acid, Wet Gun Cotton Penta Erythritol Tetranitrate RDX, Tri-nitro Resorcinol (Styphnic Alid) ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 209 7. Picric Acid As for Class 1 Unlimited Unlimited 8. Gun As for Class 1, provided that the inner or outer Unlimited Unlimited Cotton package or both of them shall be of such nature, so wetted and so closed, as to prevent any material loss with water of moisture. as to be absolutely un-inflamm- able 9. Penta- In double package, the inner package shall be a 22.5 Kilogrammes 11.25 Kilogrammes Erythritol polythene bag closed at the top with twine thread (dry basis) (dry basis) Tetranitrate and placed in a bright tin container. Both the (P.E.T.N bag and the tin container shall be so closed as to Penthrite) prevent any material loss of moisture. The outer containing package shall be as defined in clause (1) of the 25% of Schedule and so closed as to prevent any material moisture loss of moisture. 10. RDX As for PETN 22.5 Kilogrammes 11.25 Kilogrammes (dry basis) (dry basis) 11. Tri- Nitro- As for Class 1, provided that Tri-nitro-Resorcinol 25 Kilogrammes 25 Kilogrammes Resorcinol (Styphnic Acid) shall be wetted with not less than of wet explosive of wet explosive (Styphnic 20% of water calculated on the wet explosives and Acid) that the inner package shall be a substantial bag, case or canister so made and closed as to prevent any loss of moisture or escape of explosives. 12. Class 4 As for Class 3, Division 1, other than propellants. 25 Kilogrammes 2.5 Kilogrammes Division 1 13. Class 4 As for Class 1 25 Kilogrammes . 2.5 Kilogrammes Division 2 14. Class 5 The explosives shall be packed wet containing not 100 Kilogrammes . 12.5 Kilogrammes less than 25% water, and shall in this condition be enclosed in a treble package; the inner most package containing the wet cloth or other suitable material of close mesh but permeable to water; the intermediate package shall contain all the individual packages and sufficient water to keep the explosive in them cons- tantly wet, and may, consistent with the requirements of the security of the whole package, be in the form of a rubber bag, or of a case, or of such special lining to the other packages as will efficiently attain this object, and it must itself be constantly surrounded by or saturated with water, the outer package contai- ning sufficient water constantly to surround the case. Both the intermediate package and the outer package shall be of such construction and material as will not allow water to escape. 15. Class 6, A single outer package. Provided that clause (3) Unlimited Division 1, of this Schedule shall not apply to explosives of other than this Division: Pin-fire Provided also that bulleted cartridges of a calibre cartridges exceeding 1.27 centimetres. And belonging to this for pistols. Division shall be packed in such a manner that the (1) (2) (3) (4) (5) 210 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] point of any bullet cannot come in contact with the cap of another cartridge. 16. Pin-fire (a) Not exceeding 50 in number in any one 2500 in number 50 in number cartridges consignment—So packed in a single package for pistols that the bases lie alternately in opposite directions. The bases and pins shall be so fitted into perforations in millboard or other suitable material as to prevent the firing of any one of the said cartridges by an explosion in any other of the said cartridges. (b) Exceeding 50 number-In an inner and outer package, the cartridges being packed in inner packages with millboards as above required. 17. Class 6, Explosives made up into cartridges or charges for 2500 in number 50 in number Division 2 cannon, shell, torpedoes, mines, blasting or other like purposes shall be packed in such manner and in such quantity as is required for the same explosive when not so made up: Provided that, where a double package is required, the enclosing ease of such cartridges or charges may, if it satisfies the conditions required for an inner packages, be deemed to be such inner package. Other ammunition of this Division-A single outer package. 18. Class 6 As for Class 1 10,000 in number 1,000 in number Division 3, Provided that bulleted cartridges of a calibre other than exceeding 1.27 centimetres. And belonging to this Detonators Division shall be packed in such a manner that the and Electric point of any bullet cannot come in contact with the Detonators cap of another cartridge. (a) Not exceeding 1,000 in any one consignment. As for Class 1, provided that the detonators and the spaces between the same and between the sides of the inner package and the said detonators shall all be filled as far as practicable, with fine sawdust or other similar material; a layer of felt or other soft yielding material shall be placed between both ends of all the deto- nators and the interior of the inner package in which the same are placed, in such manner and so secured, that both ends of the detonators will rest upon the said cotton wool or other material, every inner package, if of metal to be lined throughout with the paper or other soft material. (b) Exceeding 1,000 detonators. The detonators shall be packed in inner packages, with sawdust and cotton wool as above described. Such inner packages shall be placed inside a substantial case of wood or metal, made and closed so as to prevent any of the inner packages escaping there from, and such case shall be placed inside an outer package in such manner and so secured (1) (2) (3) (4) (5) ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 211 as to leave a clear space of not less than 7.5 centimetres. Between the case and every part of the interior of the said outer packages, notwith- standing that such clear space may, if preferred be filled with sawdust, straw or other similar material or may contain a light framework or battens of wood to keep the case aforesaid in position in the outer package. (c) Where the number of detonators exceeds 5,000 such other packages shall be provided with handles or other contrivance, by means of which it can be safely and conveniently carried. 20. Electric As for Class 1, provided that the number in any 2,000 in number 100 in number Detonators outer package shall not exceeds 2,000. 21. Class 7 Double package, the inner package being 10 Kilogrammes 0.5 Kilogrammes Division 1 hermetically closed and contained in an outer package as above defined. 22. Class 7 Double package, the inner and outer packages made 50 Kilogrammes Division 2 of wood being as defined in clause (1) of this Sub- Schedule. Inner Packages made of card board. division 1, 2 and 3 except serpents and paper caps or amerces 23 Class 7 Double package, the inner and outer packages being 20 Kilogrammes Division 2 as defined in clause (1) of this Schedule. Inner Sub-division Packages made of card board 1, 2 and 3 except serpents and paper caps or amerces 24 Class 7 Double package, the inner and outer packages being 15 Kilogrammes Division 2 as defined in clause (1) of this Schedule. Inner Sub-division Packages shall be filled with cotton or suitable 1for serpents material to protect from breakage of serpents palates 25 Class 7 Double package, the inner and outer packages 2.8 Kilogrammes Division 2 made of wood being as defined in clause (1) of this Sub-division Schedule. Inner Packages shall be made as per 2 for paper rule 34 caps or amerces 26 Class 7 Double package, the inner and outer packages 1.4 Kilogrammes Division 2 corrugated boxes being as defined in clause (1) of Sub-division this Schedule. Inner Packages shall be made as per 2 for paper rule 34 caps or amerces (1) (2) (3) (4) (5) 212 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 27 Class 7 Single out package and inside of outer box shall be 25 Kilogrammes -- Division 3 secured by cushioning material 28 Class 7, Single outer package provided that clause (3) of 50 Kilogrammes . -- Division 4 this Schedule shall not apply. or as approved by Armed Forces of the Union 29. Class 8, Cartridges packed and transported for immediate -- -- L.O.X. use in insulated packing boxes of a design (Liquid approved by the Chief Controller Oxygen Explosives Part - 2 Methods of packing of explosives for import and export (see rules 14 and 15) (1) The methods of packing of explosives for import and export shall comply with the Scheme of classification of dangerous goods of U N class 1 (i.e., explosives) in combination with the hazard Division and the Compatibility Group devised by United Nations as ‘Transport of Dangerous Goods’ and accepted world wide as harmonised International Regulations as amended from time to time for governing the various modes of transport of dangerous goods. Schedule III Methods of testing ( see rule 48) An explosive of the 3rd (Nitro-compound) Class or of the 4th (Chlorate-mixture) Class shall comply with the tests set forth in this Schedule as applicable to such explosive. Heat test as applied to explosives 1. Apparatus and materials employed Specifi- Pattern Article cation No. 1 2 3 4 5 A Acid, Acetic 56.8 cubic centimetres. Bottle 1 I Balance 1 II Bath, water 1 III Bath, water, for hot water heating * 1 IV Beaker, glass, 1 1/3 litres 1 V Bottle, dropper, brown glass, 28.4 cubic 1 centimetres. (for glycerine and water mixture) VI Bottle, glass-stoppered, brown glass, 28.4 cubic 1 centimetres (for standard tint papers) VII Bottle, glass-stoppered, brown glass, 1 56.8 cubic centimetres (for test papers) VIII Brush, cleaning 2 IX Brush, cleaning, test tube 1 (1) (2) (3) (4) (5) ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 213 X Burner, gas, Argand, and screen 1 XI Caps, for test tubes Sufficient supply B XII Chalk, French Sufficient supply XIII Forceps, lifting, heat test papers 1 XIV Funnel, aluminium 1 C XV Funnel, glass 1 Glycerine 28.4 cubic centimetres bottle 1 XVI Knife, cordite 1 XVII Lid, Water bath 1 SVIII Mill, cordite 1 XIX Needle, piercing, heat test papers 1 XX Oven, water 1 D Paper, filter Sufficient supply Papers, filter, 5.5 centimetres. -Do- XXI Papers, standard tint -Do- E Papers, test -Do- XXII Pestle and mortar, wedgwoodware 1 XXIII Plate, glass, resting heat test papers on when piercing 1 XXIV Rings, rubber, test tube Sufficient supply XXV Rod, glass, flat-headed 1 XXVI Rods, glass, platinum wire hook 6 XXVII Scoop, aluminium 1 XXVIII Screen, burner for water bath 1 XXIX Sieves, rectangular, tinned, brass wire 1 XXX Sieves with lid and base, Circular brass A set XXXI Spatula, horn 1 XXXII Stand, heat test tubes 1 XXXIII Stand, water bath 1 XXXIV Stoppers, rubber, perforated Sufficient supply XXXV Thermometers, glass, and wood case 2 XXXVI Trays, aluminium 6 XXXVII Tray, cordite knife 1 XXXVIII Tubes, heat test Sufficient supply XXXIX Tubes, standard tint paper 1 XL Tubing, rubber, Argand gas burner Sufficient supply XLI Weights, gramme and forecps in box A set *Alternative pattern for use where hot water is available. N.B.—The apparatus and materials are to comply in all respects with the specification and standard patterns. Specification —acid, acetic The acetic acid is to be clear, colourless and free from all impurities, and is not to contain less than 96 per cent CH 3 COOH. When 1 cubic centimetre. Of N/10 potassium permanganate solution is added to 100 cubic centimetres of the acetic acid maintained at 15oC, the distinctive colour is to remain for not less than 15 minutes. 1 2 3 4 5 214 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] One drop of the diluted acetic acid-one volume acetic acid diluted with four volumes of distilled water—when placed by means of a glass rod on freshly-prepared potassium iodide-starch paper is to produce no colour. Specification —chalk, french The French chalk is to be equal in colour, to the standard sample and is not to contain more than 0.5 per cent of moisture. The bulk of the French chalk is to be such that a volume of 50 cubic centimetres. will weigh 23.5 +1.0 grammes. This to be determined as follows: A glass funnel, the stem of which is 11 centimetres in length tapering, internally from 8 mm. at the top to 5 mm. at the end, is to be clamped vertically above a 50 cubic centimetres cylinder so that the mouth of the latter is 7 centimetres. Below the lowest point of the funnel. The cylinder is to be 2.5 centimetres. in internal diameter, with a ground edge. The French Chalk is to be poured gradually into the funnel and allowed to flow into the cylinder until the latter overflows. This should take one minute. The surface of the chalk is then to be levelled off, without tapping into the funnel and allowed to flow into the cylinder until the latter overflows. This should take one minute. The surface of the chalk is then to be levelled off, without tapping or shaking the cylinder, by drawing a straight edge over the mouth of the cylinder. The cylinder and contents are then to be weighed. The fitness of the French chalk is to be such that it will all pass, without rubbing, through a 0.075 mm. wire sieve of 6.400 meshes per square centimetre. The French chalk is not to contain more than 0.1 per cent of soluble alkali salts calculated as CaCo 3 . This is to be determined as follows: 10 grams of the chalk are to be boiled with 250 cubic centimetres of water for one minute, filtered, washed and the filtrate titrated with N/10 hydrochloric acid. The French chalk, when warmed with hydrochloric acid is not to give off more than 1 per cent and not less than 0.25 per cent of carbonic acid gas. The French chalk is not to absorb more than 0.5 per cent of moisture after being dried at 100oC till constant in weight, and then exposed under a bell-jar to saturated atmosphere at 15oC to 20oC for 24 hours. Note:— Before use in heat-test experiments the French chalk is to be carefully washed with distilled water, dried in a water oven at 65-70°C, and exposed to a saturated atmosphere for 24 hours. It is to be kept in a well-stoppered bottle. Specification—glycerine The glycerine is to comply with the latest edition of British Pharmacopoeia Specification in all respects. Specification—paper, filters The paper for making heat test paper is to consist entirely of pure normal cotton cellulose of strongly resistant quality and free from any loading or sizing. During manufacture, the paper is not to be submitted to artificial heat of any kind. The paper is to have a smooth white surface, and both sides are to be as nearly alike as possible. The average length of the fibres is to be 2±0.5 millimetres. The sheets, when measured with a Ciceri smith's patent fixed pressure micrometer, are to have a thickness of 1.8 ±0.2 millimetres. The last treatment in its preparation is to be a thorough washing with pure distilled water and subsequent air drying in a pure atmosphere. The paper is to be free from all traces of chemical or other impurity particularly acids, chlorine and peroxides. On boiling with 3 per cent, caustic soda solution for 60 minutes, the paper is to lose more than 7.5 per cent of its weight. When heated for 15 minutes at 100o C with Fehlings's solutions, diluted with twice its volume of boiling water, it is not to produce more than 1.25 per cent of its weight of cuprous oxide (Cu 2 O). ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 215 It is to be supplied in sheets 50 centimetres. long by 15 centimetres. wide, and each 100 sheets packed separately in a hermetically sealed tin case closed by a tear-off strip. For use in the extraction of nitro-glycerine from dynamite it is to be supplied in circles 5.5 centimetres in diameter, each 100 papers being packed separately. Specification—papers, test The papers are to be prepared and tested by the method laid down in Appendix II. Each batch of papers is to be tested by carrying out four consecutive tests of four papers on each of two days. The mean test obtained is to be 18.5± 0.75 minutes. A test different from the mean by more than two minutes is to be considered abnormal, and is to be disregarded unless there are more than one of such abnormal tests amongst the 32 papers tested, in which case the batch is to be condemned. Specification—papers, standard tint The standard tint papers are to be made by the method described in, and are to conform to the conditions laid down in Appendix I. II—Preparation of the sample to be tested: All the operations in preparing a sample for testing are to be carried out as expeditiously as possible, avoiding exposure to light, as far as practicable and the test is to be carried out as soon as the sample is prepared. In weighing out heat test quantities, an accuracy of ± 0.05 gramme is sufficient. These quantities are to be weighed out into test tubes which have been fitted with rubber rings, the Explosives of Class 3, Division 1. (1) Friable Nitro-glycerine preparations from which the nitro-glycerine or liquid nitro-compound cannot be conveniently extracted with water- (a) A cartridge of the sample to be tested is to be opened at one end and rotated with one hand while with the other contents of the cartridge are to be loosened by means of pressure between the thumb and forefinger. The first 12.7 millimetres of the sample so loosened is to be rejected. (b) The cartridge is then to be inverted over the scoop and the loosening operation continued so as to transfer a portion of the explosive to the scoop. (c) When the weight of the sample in the scoop has been adjusted to 3.2 grammes the sample is to be transferred by means of the aluminium funnel to a heat test tubes collected at the bottom by gently tapping the side of the tube with the fingers and pressed down to a height of 3 centimetres by means of the flat-headed glass rod. The sample is then ready to be heat tested. (2) Blasting Gelatine and Analogous Preparations- (a) The wrapper of the cartridge is to be opened out and 12.7 millimetres of the sample is to be removed with the spatula and rejected. A price weighing 3.2 grammes as nearly as can be judged is then to be cut off for test. The sample is to lie on its own wrapper during these operations, and direct contact of the operator's hands with the sample is to be avoided. (b) The portion of the sample removed is to be weighted in the scoop and pieces added to, or removed from it, until 3.2 grammes are obtained. This quantity is then to be transferred to the mortar. 6.5 grammes of French Chalk are to be weighed out using the spatula and scoop and also transferred to the mortar. (c) The sample is to be incorporated with the French Chalk by repeatedly squeezing it with the end of the pestle, until it is in a condition in which it can be ground. The times for normal samples should generally be as follows: Blasting gelatine 1 ½ minutes. Gelatine dynamite 1 minute. Gelignite and Similar ½ minute. Explosives containing less than 63 per cent of Nitro-glycerine. The mixture is then to be ground by a circular movement of the pestle for a further period of half a minute, and should then be homogenous in appearance. 216 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (d) The mixture is to be transferred to a test-tube by means of the horn spatula and the aluminium funnel, and gently pressed down to a height of 5 centimetres with the flat headed glass rod. The sample is then ready to be heat tested. (e) The pestle and mortar after each grinding are to be thoroughly washed with tap water, rinsed with distilled water, dried with a clean towel, and finally dried in a bath at 100o C. The pestle and mortar are to be allowed to cool to the ordinary temperature before being used again. (3) Cordite, Ballistite and other propellants of Class 3, Division 1- (i) Explosives in the form of sticks or tubes— (a) The operator is to wash his hands carefully, thoroughly rinse them in distilled water, and dry them with a clean towel. (b) The sticks or tubes to be tested are to be wiped out with clean filter paper. (c) The sample is to be reduced to a condition suitable for grinding in the cordite mill by being cut into small piece about 3.175 millimetres. long by means of the cordite knife, 12.7 millimetres being rejected from each end of the sticks or tubes to be tested. (d) The set of sieves with the lid removed is to be placed under the mill so as to allow the ground material to fall directly on the top sieve. (e) The cut sample is to be transferred from the cordite tray to the mill and ground. The first portion passing through the mill is to be rejected. A sufficient quantity of the sample is to be taken to ensure that enough material is obtained on the second sieve without grinding the whole quantity introduced into the mill. (f) The lid is to be replaced on the set of sieves and the sample is sieved for one minute. The material which remains on the second sieve is to be taken for heat test, except in the case of powder in sticks or tubes the nominal diameter of which is less than 0.762 millimetres. in this case, the material in the bottom compartment is to be taken for heat test. (g) 1.6 grammes of the ground and sieved sample are to be weighed out in the scoop, transferred by means of the aluminium funnel to a heat test tube and collected at the bottom by gently tapping the side of the tube with the fingers. Three such test quantities are to be so weighed out. The sample is then ready to be heat tested. (h) The set of sieves and the cordite mill are to be cleaned with the cleaning brush before and after the preparation of each sample. (ii) Explosives in the form of grains for small arms.—1.6 grammes of the sample is to be weighed out in the scoop, transferred by means of the aluminium funnel to a heat test tube and collected at the bottom by gently tapping the side of the tube with the fingers. Three such test quantities are to be weighed out. The sample is then ready to be heat tested. Explosives of Class 3, Division 2 (1) Nitro-cellulose Pulp— (a) The operator is to wash his hands carefully, thoroughly rinse them with distilled water and dry them with a clean towel. (b) Six thickness of filter paper are to be laid on top of one another. Sufficient quantity of the sample to be tested, to give about 5.6 grammes after the final pressing, is to be spread on the top sheet. Six other thickness of filter paper are to be similarly laid over the sample. The whole is then to be placed under pressure as, for instance, in a hand screw press, and pressure applied for three minutes. On removal from the press, the sample is to be rubbed up by hand on the filter paper and again pressed for three minutes on fresh filter paper. The sample is then to be transferred to the rectangular sieve and rubbed through it with the hand. (c) 5 grammes of the sieved sample are to be weighed out in the scoop and spread evenly on an aluminium tray. (d) The oven is to have been brought to, and is to be maintained at a temperature of 48.9oC (120oF) the tray is to be placed in the oven and kept there for 15 minutes with the door closed. (e) The tray is to be removed from the oven and the sample transferred to the top sieve of the set of sieves. The lid is to be replaced, and the sample sieved for two minutes. For this operation the second sieve is not to be used. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 217 (f) The portion of the sample, which passes through, the top sieve is again to be spread evenly on an aluminium tray and exposed to the air of the room for four hours. (g) 1.3 grammes of the exposed sample are to be weighed out in the scoop and transferred by means of the aluminium funnel to a heat test tube. Two such test quantities are to be so weighed out. The material in each is to be gently pressed down with the flat headed glass rod to a height of three centimetres. The sample is then ready to be heat tested. (h) The wire sieve and the set of sieves are to be cleaned with the cleaning brush before and after each sample has been sieved. (2) Compressed Guncotton — (a) About 10 grammes of guncotton are to be removed from the centre of the primer or slab by scrapping with the horn spatula. (b) The scrapping so obtained are to be placed in the glass beaker two thirds full of cold distilled water. The sample is to be frequently stirred up on the water during 15 minutes with the flat headed glass rod, and then allowed to settle. The water is to be poured off and replaced by a similar quantity of distilled water in which the sample is to be frequently stirred up as before during 15 minutes. After setting, the second wash water is to be poured off. (c) The operator is to wash hands carefully, thoroughly rinse them with distilled water and collect the sample by hand squeezing out the excess of water. (d) Six thickness of filter paper are to be laid on top of one another. The washed guncotton is to be spread on the top sheet. Six other thickness of filter paper are to be similarly laid over the sample. The whole is then to be placed under pressure as, for instance, in a hand screw press and pressure applied for three minutes. On removal from the press, the sample is to be rubbed up on the filter paper by hand and again pressed for three minutes on fresh filter paper. The sample is then to be transferred to the rectangular sieve and rubbed through it by hand. (e) 5 grammes of the sieved sample are to be weighed out in the scoop and spread evenly on an aluminium tray. (f) The above is to have been brought to, and is to be maintained at a temperature of 48.9oC(120oF). The tray is to be placed in the oven and kept there for 15 minutes, with the door closed. (g) The tray is to be removed from the oven and the sample transferred to the top sieve of the set of sieves. The lid is to be replaced, and the sample sieved for two minutes. For this operation the second sieve is not to be used. (h) The portion of the sample, which passes through, the top sieve is to be again spread evenly on an aluminium tray and exposed to the air of the room for four hours. (i) 1.3 grammes of the exposed sample are to be weighed out in the scoop and transferred by means of the aluminium funnel to a heat test tube. Two such test quantities are to be so weighed out. The material in each is to be gently pressed down with the flat-headed glass rod to a height of three centimetres. The sample is then ready to be heat tested. (j) The wire sieve and the set of sieves are to be cleaned with the cleaning brush before and after each sample has been sieved. (3) Nitro-cellulose Propellant — (i) Explosives in the form of sticks or tubes: (a) The operator is to wash his hands carefully, thoroughly rinse them in distilled water, and dry them with a clean towel. (b) The sticks or tubes to be tested are to be wiped with clean filter paper. (c) The sample is to be reduced to a condition suitable for grinding in the cordite mill by being cut into small pieces about 3.175 millimetres long by means of the cordite knife 12.7 millimetres being rejected from each end of the sticks or tubes to be tested. (d) The set of sieves with the lid removed, is to be placed under the mill so as to allow the ground material to fall directly on to the top sieve. 218 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (e) The cut sample is to be transferred from the cordite tray to the mill and ground. The first portion passing through the mill is to be rejected. A sufficient quantity of the sample is to be taken to ensure that enough material is obtained on the second sieve without grinding the whole quantity introduced into the mill. (f) The lid is to be replaced on the set of sieves and the sample is to be sieved for one minute. The material which remains on the second sieve is to be taken for heat test, except in the case of powder in sticks or tubes, the nominal diameter of which is less than 0.762 millimetres in this case, the material in the bottom compartment is to be taken for heat test. (g) 1.6 grammes of the ground and sieved sample are to be weighed out in the scoop, transferred by means of the aluminium funnel to a heat test tube, and collected at the bottom by gently tapping the side of the tube with the fingers. Three such test quantities are to be so weighted out. The sample is then ready to be heat tested. (h) The set of sieves and the cordite mill are to be cleaned with cleaning brush before and after the preparation of each sample. (i) The explosives in the form of grants for small arms— (a) A quantity of the sample sufficient for the tests required is to be spread evenly on an aluminium tray. (b) The oven is to have been brought to, and is to be maintained at a temperature of 48.9oC (120o F). The tray is to be placed in the oven and kept there for 15 minutes, with the door closed. (c) The tray is to be removed from the oven and exposed to the air of the room for 4 hours. (d) 1.3 grammes of the exposed sample are to be weighed out in the scoop and transferred, by means of the aluminium funnel to a heat test tube. Three such test quantities are to be so weighed out. The sample is then ready to be heat tested. III—Application of the Test (a) The water bath is to be fitted up and is to be levelled and filled with water up to the outflow. It is to be placed on a table of convenient height in such a position that the heat test tint can readily be observed by reflected light. No part of the apparatus to be exposed to direct sunlight. (b) The thermometer fixed in the rubber stopper, is to be inserted in the wire cage provided for the purpose on the under side of the water bath of 7.6 centimetres. The water is heated to the required temperature, and maintained at a constant temperature and depth. The temperatures for the various explosives are given in Table-I. (c) The glass rod with platinum wire hook is to be inserted in the rubber stopper. A test paper is then to be removed from the brown glass bottle by means of the forceps placed on the glass plate so that its edges coincide with the lines on the plate, and pierced by passing the needle through the paper and the hole in the plate. The test paper is then to be held by means of the forceps, and a mixture of equal volumes of distilled water and glycerine is to be applied to the upper edge of the test paper by means of the glass rod of the dropping bottle in sufficient quantity to moisten the upper half of the test paper by the time the test is complete. The platinum wire hook of the glass rod is then to be passed through the hole in the paper. At no time is the operator to touch the paper with his finger. (d) The rubber stopper carrying the glass rod and test paper is at once to be firmly pressed into the test tube containing the explosives to be tested until the bottom of the stopper coincides with the top line etched on the test tube and the position of the glass rod is to be adjusted, so that the lower edge of the wet portion of the test paper, which edge is to be approximately horizontal, coincides with the middle etched line on the test tube. The test tube is then to be inserted in one of the wire cages of the lid of the water bath, so that the bottom line etched on the test tube coincides with the upper surface of the lid. The rubber ring is to pressed down on the bath and the cap placed in position over the tube. The quantities of the various explosives to be placed in the test tube are given in Table-I. The test paper is not to be inspected by lifting the cap until shortly before the time explosive ought to stand the test as given in Table-I. (e) The test is completed when the faint brown line, which after time makes its appearance at the margin between the wet and the dry positions of the test paper, equals in depth of tint the brown line on the standard tint paper. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 219 For any given explosives to pass the test, the time elapsing between the introduction of the tube into the bath and the production of the tint equal to the standard must not be less than the time given in table below: Class Division Explosive Nature Temperature of Quantity of Time explosive Heat Test Tested Explosive Heat should stand Tested the Test 3 1 Friable Nitro-glycerine preparations oC 3.2 Min from which the Nitro-glycerine cannot 71.1 grammes 7 conveniently be extracted by water. (160o F) Blasting Gelatine, and Analogous 71.1 3.2 10 preparations. (160o F) grammes +6.5 grammes French chalk Cordite, Ballistic and other propellant of 71.1 1.6 grammes 10 Class3, Division 1. (160o F) 3 2 Nitro-cellulose, pulp, compressed 76.7 1.3 gramme 10 Gun cotton. (170o F) Nitro-cellulose Propellants 76.7 1.3 grammes 10 (170o F) After the test is finished, the explosive is to be carefully removed from the tubes, and the tubes thoroughly washed out with tap water by means of the test tube brush. They are then to be rinsed out and allowed to drain for a few minutes. The washing is repeated with distilled water, the tubes rinsed, allowed to drain, and finally dried in a bath at 100° C. The tubes are to be allowed to cool to the ordinary temperature before being used again. IV—Exudation and liquefaction test for Blasting Gelatine and analogous preparations Test for Liquefaction A cylinder of blasting gelatine is to be cut from the cartridge to be tested, the length of the cylinder to be about equal to its diameter and the ends being cut flat. The cylinder is to be placed on end on a flat surface without any wrapper and secured by a pin passing vertically through its centre. In this condition the cylinder is to be exposed for one hundred and forty-four (144) consecutive hours (six days and nights) to a temperature ranging from 29.40o C to 32.2o C and during such exposure the cylinder shall not diminish in height by more than one-fourth of its original height, and the upper cut surface shall retain its flatness and the sharpness o f its edge. Note:— If the blasting gelatine and gelatine dynamite to be tested cannot be made up in cylindrical form, the test is to be applied with necessary modifications. Test for liability to exudation (‘‘Freezing and thawing test’’) There shall be no separation from the general mass of the blasting gelatine or gelatine dynamite of any nitro glycerine or liquid nitro-compound under any conditions of storage, transport or use or when the material is subjected to the liquefaction test hereinbefore described or when subjected three times in succession to alternate freezing and thawing i.e. storage at -3 to -6oC for 16 hours (freezing) followed by 8 hours at room temperature (thawing). The cycle is repeated three times (3 days) and the explosives are examined for any abnormality in respect of gel segregation or oozing out of nitro glycerine V-Picric Acid (1) The material shall contain not more than 0.3 part of mineral or non-combustible matter in 100 parts by weight of the material dried at 71.o C (160o F ). (2) It should not contain more than a minute trace of lead. (3) One hundred parts of the dry material shall not contain more than 0.3 part of total (free and combined) sulphuric acid, of which not more than 0.1 part shall be free sulphuric acid. 220 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (4) Its melting point should be between 120o C and 122.8o C. VI- Testing Chlorate mixtures The material must not be too sensitive and must show no tendency to increase in sensitiveness on keeping. The material must contain nothing liable to reduce the chlorate. Chlorites calculated, as potassium chloride must not exceed 0.25 per cent. The material must contain no free acid, or substance liable to produce free acid. Explosives of this class containing nitro-compounds will be subject to the heat test as they belonged to Class 3. Note:--These explosive will considered too sensitive if they can be exploded however, partially by means of a glancing blow with a broom stick on soft wood such as deal. VII-PETN (Penta Erythritol Tetranitrate) (A) Heat Test:-- If the sample is received dry, it is to be transferred to a clean sheet of paper and mixed thoroughly in an atmosphere free from dust. Sample of moist PETN is to be dried prior to being heat tested by taking the same in a tared flat-bottomed dish and expose the dish and its contents in a oven at a temperature not exceeding 60o C until constant in weight. 1.3 grammes of the dry sample is carefully transferred to a heat test tube by means of the aluminium funnel. After removal of the funnel the sample is to be collected at the bottom of the tube by tapping with the fingers. It is then to be heat tested at a temperature of 76.6o C and the time explosive should stand the test, should not be less than 10 minutes. (B) Other tests and requirements- (1) The PETN should be in the form of white crystals. (2) It should be free from gritty particles, visible impurities and foreign matter. (3) Melting point-The melting point of the PETN should be between 139o C and 142o C. (4) Insoluble matter-The total insoluble matter in acetone should not be more than 0.05 per cent. (5) Volatile matter-Volatile matter should not be more than 0.15 per cent. (6) Acidity-The acidity, calculated as HNO 2 should not exceed 0.01%. (7) Alkalinity-The alkalinity, calculated as Na 2 Co 3 , should not be more than 0.01%. (8) Nitrogen content-The nitrogen content should be not less than 17.40 per cent and not more than 27.80 per cent. Appendix 1 to Schedule III Preparation of Standard Tint Papers 0.48 grammes of the finest yellow ochre, 0.2 gramme of raw umber and 5 grammes of fine white gum arabic, all of which have been very finely ground in an agate mortar are weighed into a stoppered bottle of about 150 cubic centimetre capacity and 100 cubic centimetre of water added. The whole is shaken in the cold until the gum is dissolved. The suspension is then well shaken and allowed to stand for one hour. A stylographic pen is then filled from the centre of the suspension and with the aid of a ruler lines are drawn at a steady pace across one side, of a sheet of filter paper to Specification D. The sheet is then cut up into rectangular strips 1 centimetres broad by 2 centimetres long, each with a line across the middle perpendicular to the length of the strip. The breadth of the line must be not less than 0.5 millimetres. not more than 1 millimetres. In order to maintain continuity as regards depth of tint strips in which the tint does not correspond with that of the sealed pattern are to be rejected. Appendix 2 to Schedule III Preparation and Testing of Heat Papers Preparation Potassium Iodide: The purest potassium iodide obtainable commercially is to be purified by triple re-crystallisation from pure ethyl alcohol, diluted by the addition of one-twentieth of its volume of distilled water. The crystals are to be kept as small as possible, and are to be spread out on clean filter paper, resting on a glass plate, and allowed to dry in the dark,. When dry, ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 221 they are to be placed in a thin layer on the bottom of a platinum crucible and heated to a dull red heat for one minute over a spirit lamp burning pure alcohol. When cold the crystals are to be transferred to a brown glass stoppered bottle from which the quantities required are to be weighed out. The potassium iodide used for each batch of filter paper is to be prepared as above immediately before use. Starch : The starch used is to be best maize starch in the form of cornflower. It is to be purified immediately before use by washing six times by decantation with freshly distilled water. It is then to be placed on a porous plate of unglazed porcelain, allowed to dry in a warm atmosphere in the dark, and stopped in a brown bottle from which the quantities required are to be weighted out. Preparation of the Dipping Solution: 220 cubic centimetres of freshly distilled water are to be placed in a Jena glass flask and raised to boiling point over a spirit lamp burning pure spirit. 3 gram of the starch, prepared as above, are to be suspended in 30 cubic centimetre of distilled water and the mixture poured into the 220 cubic centimetres of boiling water, with continuous shaking. The whole is to be kept boiling gently, and shaken occasionally for 5 minutes. The solution of starch so prepared is to be added to a solution of 1 gramme of the purified potassium iodide in 250 cubic centimetre of freshly distilled water, and the solution well mixed. The mixture is to stand overnight in a dark room. The following day, the clear supernatant liquid is to be carefully siphoned off and used immediately for dipping the paper. If it is desired to dip a large batch of paper, the foregoing quantities may be multiplied in order to obtain sufficient solution. Dipping the papers: The clear potassium iodide and starch solution is to be poured into a porcelain tray, which is to be kept exclusively for this operation. Sheets of filter paper to Specification D are to be passed through it singly, so that all except 3 centimetres at the end of the strip of paper passes beneath the surface of the liquid. The strip of paper is to be held above the tray by the dry portion and a glass rod passed down each side to remove the excess of solution. It is then to be suspended by the undippened portion in a warm dark room, cupboard, or oven until dry. It is advisable to nip a small piece, out of the edge of each sheet at the boundary line between the wet and dry portions as a guide in subsequent cutting. Cutting and Trimming the Test Paper : In cutting and trimming heat test paper the operator is to wear clean cotton gloves. When the sheets are dry they are to be trimmed by cutting off the unclipped end about 0.5 centimetre below the edge of the undipped portion, 0.5 centimetres strips are also cut from the other three edges. The sheets are then to be stored in amber coloured glass jars, kept in the dark. When a batch of paper has been passed for issue the sheets are to be cut up into rectangular pieces 1 centimetre by 2 centimetres, and are to be issued in this form. All the above operations are to be carried out in a building specially reserved for this work. This building is to be protected from the direct access of the sun's rays, and is, as far as possible, to be kept dark. Testing of Heat Test Paper by the Diffusion Test Apparatus and Materials required : No. 1. Acheson graphite Pieces, 1 2. Acid, Sulphuric, normal solution Sufficient supply 3. Annulus aluminium 2 4. Cap, light-tightpaste board 1 5. Cylinder, glass, with rubber stopper 1 6. Cylinder, measuring 100 cubic centimetres 1 7. Ferrous ammonium sulphate Sufficient supply 222 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 8. Jar, cylindrical, brown glass 1 9. Pipette 10 cubic centimetres 1 10. Rod, stirring, glass 1 11. Sodium nitrite solution containing 1.7 grams in 1 litre Sufficient supply 12. Stopper, rubber, with 4 platinum hooks 1 Application of the Test : The solution is to be brought to 15o C before use. 2 grammes of ferrous ammonium sulphate are weighed out and placed in the glass jar, 90 cubic centimetres of the normal sulphuric acid added and solution effected by stirring with the glass rod. The jar is then placed in a bath of water at 15o C, and must be kept at the temperature of the air should be 15o C to 17o C. 10 cubic centimetres of the sodium nitrite solution are then added by means of the pipette and well stirred in. An aluminium annulus is placed centrally over the mouth of the jar and the orifice covered by the graphite slab; over this is placed a second annulus. Good contact between surfaces is to be ensured by exerting a slight pressure and twisting motion. The glass cylinder with rubber stopper and light tight cap are then placed on the second annulus, and the assembled apparatus is allowed to stand for 20 minutes. After the expiration of the 20 minutes, the light tight cap and the glass cylinder are removed, the rubber stopper taken out of the cylinder waved several times through the air. As soon as possible, four of the heat test papers to be tested are moistened with glycerine solution, placed on the platinum hooks of the stopper, the stopper inserted in the cylinder, and the cylinder and light tight cap again placed in position of the second annulus, and the time noted. When the papers read by reflected light reach the standard, tint, the time is again noted; the difference gives the time of test. Standard tint papers to be read by reflected light are used for comparison. The cylinder is then removed uncorked, waved several times through the air, and a fresh set of papers is at once put on for test. After four sets of tests have been made the graphite slab must be heated to 200o C for 1 hour allowed to cool in an evacuated desiccators over potash for at least 16 hours before being used again. A batch of papers is to be tested by carrying out four consecutive tests of four papers on each of two days. SCHEDULE IV Part 1 (See rule 99) Licences and licensing authorities Article No. Purpose for which granted Licence Form Licensing Authority 1 2 3 4 1 (a) Licence to manufacture fireworks or gunpowder or both LE-1 District Magistrate. not exceeding 15 kilogrammes at any one time. (b) Licence to manufacture fireworks or gunpowder or both LE-1 Controller of Explosives. exceeding 15 kilogrammes but not exceeding 500 kilogrammes at any one time. (c) Licence to manufacture fireworks or gunpowder or both LE-1 Chief Controller or exceeding 500 kilograms at any one time. Controller of Explosives authorised by Chief Controller. (d) Licence to manufacture at site, ANFO explosives not LE-1 Controller of Explosives exceeding 200 kilogrammes at any one time. (e) Licence to manufacture liquid oxygen explosives (LOX). LE-1 Chief Controller or Controller of Explosives authorised by Chief Controller. (f) Licence to manufacture site mixed explosives (SME) LE-1 Chief Controller or Controller of Explosives authorised by Chief Controller. No. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 223 (g) Licence to manufacture explosives other than fireworks, LE-1 Chief Controller or gunpowder, ANFO, LOX and SME. Controller of Explosives authorised by Chief Controller 2 Licence to possess gunpowder not exceeding 15 kilogramme LE-2 District Magistrate at any one time for manufacture of adirverttus and possession of adirverttus not exceeding 200 in number at any one time. 3 (a) Licence to possess for use, for agricultural purpose or in LE-3 District Magistrate small quarry, explosives not exceeding 25 kilogrammes of Class 1 or 2 or 3 and 1500 numbers detonators; and 1500 meters of detonating fuse or safety fuse at any one time in a magazine. (b) Licence to possess for sale, explosives of Class 1, 2, 3, 4, LE-3 Chief Controller or 5, 6 or 7 in a magazine. Controller of Explosives authorised by Chief Controller (c) Licence to possess for use, explosives of Class 1, 2, 3, 4, LE-3 Chief Controller or 5, 6 or 7 in a magazine. Controller of Explosives authorised by Chief Controller (d) Licence to possess fireworks not exceeding 5000 kilogramme LE-3 Chief Controller or or safety fuse not exceeding 50000 meters, in a storehouse, Controller of Explosives not for sale but for transfer to own licensed shop. authorised by Chief Controller 4 Licence to possess and transport explosives of class 2 or LE-4 District Magistrate class 3 not exceeding 25 kilograms, electric or ordinary detonators not exceeding 200 numbers, detonating fuse not exceeding 100 metres and safety fuse not exceeding 200 metres in a compressor mounted motor truck or tractor for use in well sinking. 5 (a) Licence to possess and sell from a shop, at any one time, not LE-5 District Magistrate exceeding 25 kilogrammes of small-arms nitro- compound (b) Licence to possess and sell from a shop, at any one time, LE-5 District Magistrate not exceeding 100 kilogrammes of manufactured fireworks of Class 7, Division 2, sub-division 2; and 500 kilogrammes of chinese crackers or sparklers (c) Licence to possess and sell from a shop, at any one time, LE-5 District Magistrate not exceeding 2000 numbers of pyrotechnic device explosives of Class 6 Division 1 (d) Licence to possess for use Gunpowder not exceeding LE-5 District Magistrate 5 kilogrammes and safety fuse not exceeding 50 metres in the States of Bihar, West Bengal, Kerala and Tamilnadu. (e) Licence to possess for use of small-arms nitro-compound LE-5 District Magistrate not exceeding 5 kilogrammes in the State of Kerala. (f) Licence to possess and sell from a shop manufactured LE-5 Controller of Explosives fireworks of Class 7 Division 2 sub-division 2 exceeding 100 kilogrammes but not exceeding 300 kilogrammes, and chinese crackers or sparklers exceeding 500 kilogrammes but not exceeding 1200 kilogrammes. 6 Licence to possess and use fireworks for public display. LE-6 District Magistrate 7 Licence to transport explosives in a road van. LE-7 Controller of Explosives 1 2 3 4 224 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 8 Licence to import or export explosives otherwise than by land. LE-8 Chief Controller 9 Licence to manufacture, possess, sell, use, etc of explosives LE-9 (SPECIAL) Chief Controller not provided in articles 1 to 8. 10 Shot firer's Certificate. LE-10 Controller of Explosives 11 Foreman's Certificate. LE-11 Controller of Explosives Part 2 (See rules 100 and 113) A. Fees other than licence fees and fees for testing in the departmental testing station : The following Fees other than licence fees and fees for testing in the departmental testing station shall be payable: (1) Scrutiny fee for each proposal for inclusion of any explosive in the authorised Rs. 500 list of explosives (2) Fees for testing each sample of imported explosives Rs. 100 (3) (i) Fees for testing each sample to issue certificate of safety Rs. 100 (ii) Fees to renew each certificate issued under (i) above without fresh test. Rs. 50 (iii) Fees for testing each sample to renew certificate issued under (i) above after fresh test. Rs. 500 (iv) Scrutiny fee for approval of manufacturing process for any new explosives. Rs. 2000 (4) Fees for storage of explosives in excess of licensed capacity on each occasion. Rs. 500 for first 15 days and Rs. 200 for every additional day (5) Fees for permit for temporary possession of fireworks in excess of licensed quantity Rs. 200 (6) Scrutiny fee for application for approval before grant of a licence to manufacture (i) any explosives other than those mentioned under (ii), (iii) and (iv) below Rs. 2000 (ii) site mixed ANFO Explosives Rs. 500 (iii) Liquid Oxygen explosive Rs. 500 (iv) (a) Fireworks or Gunpowder in a quantity not exceeding 15 Kilogrammes at a time. Rs. 50 (b) Fireworks or Gunpowder in a quantity exceeding 15 Kilogrammes but not exceedingRs. 500 200 Kilogrammes at a time. (c) Fireworks or Gunpowder in a quantity exceeding 200 Kilogrammes at a time Rs. 500 (7) Scrutiny fee for grant of approval to manufacture colour matches Rs. 1000 (8) Scrutiny fee for application for approval before grant of licence to possess explosives in (a) magazine or store house Rs. 500 (b) shops Rs. 200 (9) Scrutiny fee for application for grant of each licence to import or export explosives Rs. 500 (10) Scrutiny fee for application for grant of each licence to transport explosives Rs. 100 (11) Scrutiny fee for each application for grant of a licence for a road van compressor Rs. 200 mounted motor truck or tractor (12) Scrutiny fee for each application for grant of a shot-firer's certificate Rs. 300 (13) (a) Scrutiny fee for application for amendment or transfer of each licence or certificate (i) to manufacture high explosives and of Class 6 and other explosives not mentioned Rs. 1500 below: (ii) to manufacture fireworks or Gunpowder in a quantity not exceeding 15 Kilogrammes Rs. 50 at a time; 1 2 3 4 ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 225 (iii) to manufacture fireworks or Gunpowder in a quantity exceeding 15 Kilogrammes Rs. 300 but not exceeding 200 kilogrammes at a time; (iv) to manufacture fireworks or Gunpowder in a quantity exceeding 200 Kilogrammes Rs. 300 at a time; (v) to manufacture site mixed ANFO explosives; Rs. 300 (vi) to manufacture liquid oxygen explosives; Rs. 300 (vii) to possess explosives in magazine for sale or use or in store house; Rs. 300 (viii) to possess fireworks in a shop for sale; Rs. 300 (ix) to transport explosives in explosives van; Rs. 300 (x) in Form LE-3. Rs. 50 (xi) shot firer's or foreman's certificate Rs. 100 (b) Amendment or transfer fee for each licence (i) to manufacture high explosives and explosives of Class 6 and other explosives Rs. 200 not mentioned below; (ii) to manufacture fireworks or Gunpowder in a quantity not exceeding 15 Kilogrammes Rs. 50 at a time; (iii) to manufacture fireworks or Gunpowder in a quantity exceeding 15 Kilogrammes Rs. 200 but not exceeding 200 Kilogrammes at a time; (iv) to manufacture fireworks or Gunpowder in a quantity exceeding 200 Kilogrammes at a time; Rs. 200 (v) to manufacture site mixed ANFO explosives; Rs. 200 (vi) to manufacture liquid oxygen explosives; Rs. 200 (vii) to possess explosives in magazine for sale or use or in store house; Rs. 200 (viii) to possess fireworks in a shop for sale; Rs. 200 (ix) to transport explosives in explosives van; Rs. 200 (x) in form LE-3 Rs. 50 (xi) shot firer's or foreman's certificate Rs. 100 (c) Scrutiny fee for a proposal for any change in the manufacturing process of explosives Rs. 1000 (d) Scrutiny fee for a proposal for any change in the composition of an authorised Rs. 500 explosives (14) For appeal against an order of a licensing authority (i) if such appeal is preferred to Central Government or Chief Controller Rs. 1000 (ii) if such appeal is preferred to immediate official superior to District Magistrate. Rs. 200 (15) For issue of a duplicate copy of licence or certificate Rs. 200 (16) For approval of - (a) a packing box or container. Rs. 1000 (b) a new design of equipment, machinery or composite vehicle used for manufacture Rs. 1000 and transport of explosives (c) a magazine 'Mode B' Rs. 1000 (d) BMD vehicle Rs. 1000 (17) Lightning Conductor testing fee for each test conducted by Departmental officer. Rs. 500 B. Licence fee -(1) The following fees shall be payable per year for each licence issued under these rules : (I) Licenses fees for manufacture of explosives Rs.1000 per 1000 tonnes or part thereof of the (a) of classes 2,3,4 and 5 other than site mixed installed annual plant capacity for each explo- Ammonium Nitrate Fuel Oil explosive sive subject to a maximum of Rs.20,000 226 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (b) of class 6 Rs.1000 per one million metres or numbers or part thereof of the installed annual plant capacity of each explosives subject to a maximum of Rs.20,000 (c) of class 1 or class 7 (i) in a quantity not exceeding 15 Kilogrammes at a time; Rs. 200 (ii) in a quantity exceeding 15 Kilogrammes but not exceeding 200 Kilogrammes at a time; Rs. 2000 (iii) in quantities exceeding 200 Kilogrammes at a time; Rs. 2000 for the first 200 Kilogrammes plus Rs. 500 for every additional 50 Kilogrammes or part thereof at a time subject to a maximum of Rs. 15000 (d) of class 8 (Liquid Oxygen Explosive) Rs. 5000 (e) of site mixed ANFO explosives Rs. 1000 (II) Licence fees for possession and sale of explosives in a (a) Rs.1000 for every 1000 Kilogrammes or part magazine. thereof of the licensed capacity of each explosive of Class 1, 2, 3, 4, 5 or 7 subject to a maximum of Rs. 15000 (b) Rs. 500 for every 10000 metres or numbers or part thereof of each explosive of Class 6 subject to a maximum of Rs. 15000 (III) Licence fees for possession of explosives in a magazine (a) Rs. 1000 for every 1000 Kilogrammes or part for use. thereof of the licensed capacity of each explosives of Class 1, 2, 3, 4, 5 or 7 subject to a maximum of Rs.15000, and (b) Rs. 500 for every 10,000 metres or numbers or part thereof of each explosive of Class 6 subject to a maximum of Rs. 15000 (IV) Licence fees for possession and sale of fireworks or Gunpowder or smallarms nitrocompound from a shop (a) licensed by District Magistrate Rs. 500 (b) licensed by Controller of Explosives Rs. 1000 (V) Licence fees for possession of fireworks in storehouse. Rs. 3000 (VI) Licence fees for road van Rs. 2000 (VII) Licence fees for compressor mounted motor truck or tractor. Rs. 1000 (VIII) Licence fee for possession of Gunpowder for manufacture of Rs. 500 adirvettus (IX) Licence for possession of explosives for Rs. 1000 use (other than agricultural purpose) in

Previous and next

All provisions of The Explosives Rules, 2008

Questions people ask

Is rule 139 of the Explosives Rules, 2008 still in force?

No repeal of the Explosives Rules, 2008 is recorded.