LawGrids logoLAWGRIDS.ORG

Form DE - 2, The Explosives Rules, 2008: Form DE - 2

The Explosives Rules, 2008 - Form DE - 2

Text of form DE - 2

Form DE - 2

Form DE - 2 (See rule 113 of the Explosives Rules, 2008) (Distance Form to be attached to the licence) Safety distances required to be kept clear around magazine for high explosives or fire works or factory licence number……………in form ………….granted to………………. Type of structure(s) Safety distance metres Inside Safety Distance (ISD) 1. Room or works used in connection with the magazine 2. Any other explosives magazine. 3. Magazine office for this magazine Middle Safety Distance (MSD) 4. Dwelling house of the security guard of the magazine 5. Railway including private Railway 6. Canal (in active use) or other navigable water 7. Dock or Pier or Jetty 8. Public highway or Public roads 9. Private road which is a principal means of access to a temple, mosque, church, gurudwara or other places of worships, hospital, college, school or factory 10. River embankment or sea embankment or Public well 11. Reservoir or bounded tank or rope way 12 Wind mill or solar panel for power generation Outside Safety Distance(OSD) 13. Dwelling house 14. Government and Public building 15. Temple, mosque, gurudwara, church or other place of worship 16. Shops, market place, public, recreation and sports ground, College, School, hospital, theatre, cinema or other buildings, where the public are accustomed to assemble 17. Factory 18. Buildings or works used for the storage in bulk of petroleum spirit, gas or other inflammable or hazardous substance 19. Building or works used for the manufacture of explosives or of articles which contain explosives 20. Aerodrome 21. Furance, Kiln or chimney 22. Quarry or mine pit head 23. Power house or electric sub-station 24. Wireless Station 25. Warehouse or other storage buildings 26. Any other protected works Overhead Electric lines 27. Electric Power overhead Transmission lines above 440 V 28. Electric Power overhead Transmission lines up to 440 V [Controller of Explosives/Chief Controller of Explosives] ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 301 Schedule - VI Part 1 Safety provisions for manufacture of explosives I. Process: The sensitive operations and processes including cleaning, disposal of waste, shall have control mechanism (remote control, temperature control, heating medium, etc) to the satisfaction of the Chief Controller of Explosives II. Machineries and equipments: Vessels and machineries for making and processing explosives, electrical equipments, protection against static charge, maintenance of electrical equipments, personnel protection etc should be suitable for safe operation of the process. Part 2 Safety provisions for Bulk Mixing Delivery (BMD) Vehicles (1) No welding or cutting shall be performed on a bulk mixing delivery vehicle until the vehicle has been washed down and all explosive material, ingredients, oxidizer have been removed. Before welding or cutting on a hollow shaft, the shaft shall be thoroughly cleaned inside and outside and vented with sufficient ventilation. (2) Plastic tubes shall not be used as hole liners if the hole contains an electric detonator. (3) All spills or leaks shall be cleaned up immediately. (4) No welding or open flames shall be used in or around any part of the delivery equipment unless it has been completely washed down and all oxidizer materials removed. (5) Before welding or repairs to hollow loading shafts, the shaft shall be thoroughly cleaned inside and outside and vented. (6) The entire loading and mixing equipment shall be cleaned to prevent hazardous accumulations of ingredients and before open flame work is performed on the unit. (7) Mixing of blasting agents shall not be performed during transit. (8) The location chosen for water gel or ingredient transfer from a support vehicle into the borehole loading vehicle shall be away from the blast hole site when the bore holes are loaded or in the process of being loaded. (9) No person shall smoke, carry matches or any flame-producing device, or carry any fire arms while in or about bulk vehicles effecting the mixing transfer or down-the-hole loading of blasting agents at or near the blasting site. (10) BMD vehicle shall only be driven by a capable and competent driver familiar with regulations applicable to explosive materials, and the requirements of these rules. (11) The BMD vehicle operator shall be trained in the safe operation of the vehicle, as well as with its mixing, conveying, and related equipments. The operator shall be familiar with the general procedure for handling emergency situations. (12) Caution shall be exercised in moving the vehicle in the blasting area to avoid driving the vehicle over or dragging hoses over firing lines, cap wires, or explosive materials. The driver shall obtain the assistance of a second person to guide the driver's movements when moving the vehicle in the charging area. (13) Material shall not be mixed while vehicle is in motion. (14) Pneumatic loading from bulk mixing delivery vehicles into blast holes primed with electric blasting caps or other systems sensitive to static-electricity shall be provided with semi conductive discharge hose and suitable earthing device to prevent the accumulation of static charges. (15) When electric power is applied by a self-contained motor-generator located on the vehicle, the generator shall be separated from the discharge point of the explosives. The generator or the battery shall be provided with a cut-off switch in a readily accessible position. (16) Wiring shall be so fixed and protected so as to minimize accidental damage or undue wear. (17) The BMD vehicle body and equipment shall be electrically continuous with the vehicle chassis. The frame of the mixer and all other equipment that may be used shall be electrically bonded. Bonding points and bonding cables for effective grounding shall be provided. 302 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Part-3 Safety provisions for transport of explosives by water (1) Notice of loading on or unloading from ships or vessel. —No explosive shall be loaded on or unloaded from a ship or vessel within the limits of a port unless 48 hours' notice in writing of the intended time and place of such operation has been given to the Conservator of the port. (2) Steamer fires and lights.—No explosives shall be loaded on or unloaded from any ship or vessel — (a) unless the engine room fires have been previously carefully banked up, and all other fires and lights extinguished; (b) while the ship or vessel is attached to or alongside of any steam vessel or steam tug unless the engine room fires of such steam vessel or steam tug, have previously been carefully banked up and all other fires and lights have been previously extinguished: Provided that nothing in this rule shall prevent the employment of an artificial light or ship's signal lights of a type approved in writing by the Chief Controller in areas outside the port limits and by the Conservator of the port within the port limits: Provided further that a steam tug may be employed at the port of Chennai to place boats alongside a ship carrying explosives or to remove them but no loading or unloading operations shall be carried on so long as a tug is within a distance of 50 metres from the ship. (3) Storage.—No explosives shall be stowed in a ship except in accordance with regulations contained in the Merchant Shipping Carriage of Dangerous Goods Rules, 1978. (4) Conveyance of explosives on special trade passenger ships.—Any authorised explosives satisfying the requirements of these provisions may be transported in a properly constructed magazine on a trade passenger ship to which Part VIII of the Merchant Shipping Act, 1958 (44 of 1958-Annexure II) applies being a home trade ship as defined in clause (16) of section 3 of the said Act: Provided that— (a) the consignor satisfies the certifying officer referred to in section 243 of the Merchant Shipping Act, 1958 (44 of 1958-AnnexureII) that no other means of conveying the explosives are available; (b) the magazine complies in all respects with the specifications for magazines in ships laid down by the Board of Trade and is approved by the Surveyors of the Mercantile Marine Department; (c) the explosives are packed and marked in accordance with these rules; (d) detonators are not carried in the same hold as other explosives; and (e) the hold containing the magazine does not contain any other hazardous or flammable goods at any time during which the magazine is in use for the carriage of explosives. (5) Conveyance of explosives on passenger vessels.— (1) The following explosives may be carried in a passenger vessels, namely: (a) any explosives not exceeding 2.5 kilogrammes in weight other than a fulminate (Class 5), ammunition containing its own means of ignition (Class 6, Division 3) or fireworks (Class 7); and (b) detonators not exceeding 200 in number and certified in writing by the licensee not to contain in the aggregate more than 225 grammes of explosives: Provided that— (i) previous notice is given to the person in charge of the vessel in which the explosive is intended to be conveyed; (ii) all the precautions are taken to prevent accidents by fire or explosion; (iii) Detonators are not carried in the same compartment as other explosives. (2) Nothing in these provisions shall apply to explosives carried in a passenger vessel under (1). (6) Anchorage of vessels carrying explosives.— (1) Every vessel having explosives on board and entering a port shall be anchored at such anchorage as the conservator of the port shall appoint in this behalf and shall not leave such anchorage without the general or special order of the Conservator of the port and subject to such conditions as may be specified in the order. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 303 (2) Such anchorage shall in no case be the same as that for vessels laden with petroleum and shall be at such distance from the anchorage for vessels laden with petroleum as to render it impossible for a fire originating at the former anchorage to affect vessel anchored at the later. (7) Red flag or warning light to be exhibited.—Every vessels having explosives on board exceeding 50 kilogrammes in weight shall while approaching or leaving a port and during the time that it remains within the limits of the port or on any inland water exhibit conspicuously— (a) between sunrise and sunset a red flag not less than 1 metre square, and (b) between sunset and sunrise a single red light visible all round the horizon. (8) Vessels to lie singly.—Every vessel wholly or partly laden with explosive shall lie singly and be kept at a distance of at least 50 meters from any other vessel except during the actual transhipment of explosives, when one boat may lie alongside on each side of a ship, boat or floating magazine and two ships may lie alongside each other. (9) Vessels not to lie alongside magazine, jetties, etc.—No vessel having any explosive on board shall lie alongside any vessel, floating magazine, quay wharf, jetty and land or landing stage except for the purposes of loading or unloading and then only during the time necessary for the actual loading or unloading of such vessel and shall proceed on its voyage without delay except such delay as may be unavoidable in consequence of tide or weather. (10) Loading and unloading prohibited while a vessel is underway.—No explosives exceeding 450 kilogrammes in weight and no detonators shall be loaded or unloaded while a vessel is underway. Explanation.—A vessel is 'underway' when she is not at anchor or moored or made fast to the shore or a ground. (11) Place of loading and unloading within a port area.—Explosives shall within the limits of a port, be loaded from, landed at, brought into or deposited upon, only such quay or other place as the Conservator of the Port may by general or special order direct. (12) Cushion to be used.—A cushion properly stuffed with oakum and covered with leather, or one of such other kind as the Conservator of the port may from time to time approve, shall be used in shipping an explosive in any vessel or in landing it upon any wharf or other landing place within the limits of a port. (13) Ships to handle explosives with despatch.— (1) Ships arriving in a port with explosives intended to be landed at the port shall discharge them with all reasonable despatch, and ships taking explosives on board shall proceed to sea with all reasonable despatch. (2) No ship or boat shall retain on board any cargo of explosives and remain in the port for a period longer than three days : Provided that the conservator of the port in consultation with Chief Controller may extend such period under such conditions as deemed fit if he is satisfied that such extension of period is considered necessary. (14) Boats to be licensed.— (1) No boats shall be used for the transport of explosives exceeding 1,000 kilogrammes in weight except under and in accordance with the conditions of the licence granted— (a) by the Conservator of the port in the case of a boat plying within the limits of a port, or (b) by an officer appointed by the Central Government in the case of a boat plying in areas outside port limits. (2) The licence shall specify the maximum quantity of explosives the boat is authorised to carry which quantity shall be fixed in consultation with the Chief Controller. (3) Every licence granted under these provisions shall remain valid for a period of— (a) four months in the case of a boat plying within the limits of a port; and (b) one year in the case of a boat plying in areas outside port limits. (4) The licence referred to (1) shall be granted or renewed in such form and on payment of such fees as may be specified by the Central Government. (5) A copy of every licence granted in (1) shall be forwarded to the Chief Controller. 304 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (6) Every person in charge of any boat licensed under (1) shall, when required so to do by an officer mentioned in Explosives Rule 2008 produce the licence of such boat for inspection. (15) Buoy to be carried.— (1) Every boat carrying explosives within the limits of a port shall carry on deck a buoy with a rope 27 metres in length and 7.50 centimetres in diameter, one end of the rope being attached to the buoy and the other end to the boat. The rope shall be attached to such part of the boat as is most clear of spars gear or other obstruction and at such point as is approved by the licensing authority. (2) The buoy shall be a drum painted red measuring not less than 55 centimetres in length and 35 centimetres in diameter, properly strapped with an iron band in the middle and having a ring attached for securing the rope. (16) Smoking, fire, dangerous articles and other cargo prohibited.—The following shall not be permitted on board any boat which has explosives on board— (a) fire or light of any description other than the warning lights; (b) smoking; (c) any substance of an inflammable nature or liable to spontaneous ignition; (d) any substance liable to cause or communicate fire or explosion; (e) any other cargo, unless the carrying of such other cargo, has been specially authorised in writing by the Conservator of the port within port limits or by Chief Controller in areas outside port limits: Provided that nothing in this rule shall apply to the transport of explosives in a mechanically propelled boat subject such conditions as may be specified by the Chief Controller. Part-4 Safety provisions for transport of explosives by rail (1) Rail vans to be approved.—No explosives other than safety fuse and fireworks shall be transported by rail except in a van specially constructed for the carriage of explosives and of a type approved by the Chief Controller and the Railway Board. (2) Making of railway carriage.— (1) On each side of every railway carriage containing any explosive there shall be affixed in conspicuous characters by means of a securely attached label or otherwise the word "Explosives". (2) Nothing in (1) shall apply in a carriage containing explosives transported in accordance with the provisions of Explosives Rule 2008. (3) Transport of explosives with ordinary goods.—Notwithstanding anything contained in earlier provision, the following explosives may be transported by any train other than a passenger or mixed train in a carriage not carrying any article or substance liable to cause or communicate fire or explosion: (a) any quantity of safety fuse for blasting; (b) any other explosive approved by the Chief Controller for the purpose of this rule provided such explosive is packed in metallic cases or cylinders which fulfil all the requirements of these rules and are of a pattern approved by the Indian Railways and the Chief Controller. (4) Position of railway carriages.—Every railway carriage containing explosive shall be placed as far away as practicable from the engine and shall be close-coupled to the adjoining carriages not loaded with explosives or other articles or substances of flammable or hazardous nature, provided that— (a) on the Darjeeling-Himalayan Railway carriages containing explosives need not be close-coupled; (b) on the Nilgiri and Karaikal-Peralam Railways, only one carriage need intervene between the engine and carriages containing explosives; (c) on the electrified section of Railways when trains are hauled by electric locomotives, no carriages need intervene between the engine and the carriage containing explosives. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 305 (5) Maximum quantity of explosives to be transported by rail.—Not more than 5 carriages containing explosives shall at any one time be loaded or unloaded at or on any railway station or wharf and not more than 10 carriages containing explosives shall be attached to or transported by any one train. (6) Prohibition on passenger or mixed trains.—No explosive shall be transported by any passenger or mixed train. (7) Despatch of explosive vans by mixed train—Notwithstanding anything contained in these rules, any explosive may be transported by a mixed train in vans specially approved on any line or section on which goods trains are not running subject to the following conditions, namely:- (a) not more than three such vans containing explosives shall be hauled at any one time. (b) there shall be not less than three carriages between the vans containing explosives and the engine and between such vans and the passenger carriages. (c) the vans containing explosives shall be close-coupled to the adjoining carriages and to each other. (d) immediately on entering on any section upon which goods trains are running, the vans containing explosives shall be detached from the mixed train. (8) Conveyance of explosives by passenger or mixed train—Notwithstanding anything contained in these rules, the following explosives may be transported by passenger or mixed trains: (a) safety fuses for blasting. (b) explosives of the Class 3 (Nitro-compound) other than propellants, in the form of cartridges not exceeding in the aggregate 2.5 kilogrammes in weight, provided no detonators are carried in the same compartment. (c) detonators to the number of 200 if the amount of explosives in the package or package containing detonators does not exceed in the aggregate 225 grammes provided— (i) a certificate to such effect is tendered by the consignor; and (ii) no other explosive is carried in the same compartment. (d) sporting powders and propellants packed in double packages prescribed in Schedule II, provided— (i) the explosive is contained in tin canisters containing not more than 5 kilogrammes each packed in a stout wooden case with a completely park-proof outer cover of tin or zinc or in a metal case or cylinder of a pattern approved by the Chief Controller; (ii) no outer case contains more than 12.5 kilogrammes of explosives; and (iii) the total consignment by one train does not exceed in the aggregate 37.5 kilogrammes. (9) Receipt of consignment of explosives by railways.—Consignments of explosives intended to be transported by rail shall be received only— (a) by a servant authorised by the Indian Railways concerned to receive dangerous goods; and (b) at such times between sunrise and sunset and at such places within railway premises as the Indian Railways may specify in this behalf. (10) Shunting. — No shunting of carriages containing explosives shall be carried out on any railway save under the superintendence of duly authorised officer who shall be responsible that— (a) when the train is being marshalled carriages loaded with explosives shall not be shunted by a locomotive unless they are separated from any engine by not less than three carriages containing no explosive or easily inflammable substance; (b) during the shunting of carriage containing explosive, the speed of all movements shall not exceed 8 kilometers an hour; and (c) no loose shunting take place. (11) Delivery to and from railway premises. — (1) Packages containing any explosive shall be removed by the consignee from the station, wharf or depot of the railway to which they have been transported as soon as practicable and with all due diligence after arrival. 306 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (2) If the packages are not removed within the twelve hours of daylight following their arrival the packages and contents may be forthwith returned to the consignor at his risk and expense. (3) Every package containing an explosive shall until removed, returned or despatched be kept in a safe place under the special direction of the Station Master at a safe distance from the station buildings under the police guard if necessary and shall be completely covered with tarpaulins or other suitable material. (12) Power of Indian Railways.—(1) Where Indian Railways suspects that an explosive or carriage or package containing an explosive does not comply with any of these rules, it may- (a) prevent the entry of such explosive, carriage or package upon their premises or refuse to receive or transport them; or (b) at any time open or require such carriage or package to be opened to ascertain the facts. (2) If any explosive or any carriage or package containing explosives is found not to comply with any of these rules, the Indian Railways may return such explosives carriage or package to the consignor at his risk and expense. (3) Where any explosive or any carriage or package containing explosive not complying with these rules cannot in the opinion of the Indian Railways be returned to the consignor under (2) without undue risk, it may in consultation with the Chief Controller and in such manner as he may specify, destroy at the consignor's risk and expense the explosives or the contents of the carriage or package. (13) Explosives not to be carried across railway bridges—No explosives shall be carried otherwise than by rail across any railway bridge which reasonable facilities for the transport thereof by rail are afforded by the Indian Railways: Provided that nothing in this rule shall apply to— (a) safety fuses for blasting in any quantity; or (b) gunpowder or nitro-compound not exceeding 5 kilogrammes or any quantity of ammunition, Class 6, Divisions 2 and 3. Schedule VII Specifications The specifications laid down in this Schedule are for general guidance only. Approval of the Chief Controller shall be obtained separately for each case. Specification 1: Specification of Explosives manufacturing factories other than that of fireworks 1. Site, layout, construction and safety distance A. Concept of safety distance: The location, construction and traversing of process buildings should be such that an explosion in one building does not initiate explosion in another through blast, shock , or missiles and it should cause no or little damage to personnel or property in such other buildings. Therefore the safety distances for different quantities of the different catagories of explosives (X, Y and ZZ) under Explosives Rules, are classified in three types viz. Inter Process Distance (IPD) between process buildings, Middle Safety Distance (MSD) from process buildings to facilities like highways, railways, navigable waterways, dams or reservoirs etc. and Outside Safety Distance (OSD) from process buildings to outside property, which may be built-up or inhabited, have been prescribed in the Tables 1, 2 and 3 in Schedule VIII annexed to these rules. B. Layout of facilities: The layout of different buildings should be made observing at least the minimum safety distances prescribed and taking the maximum advantage of the natural topography. Hill slopes and dense forests serve as natural protection. The difference in the ground level in a hilly area can be utilized with advantage in placing sensitive explosives buildings concealed or protected with very little additional traversing being necessary. Explosive buildings on a flat ground or on a plateau with built up area downhill are not at all desirable for the same reason. C. Construction: (a) Roof and Walls—Process buildings are constructed of strong but light walls and strong roof. Cement brick walls 22.5 centimetres thick and 15 centimetres RCC roofs are recommended. The light wall, in case of an explosion, creates light missiles, which can be contained by the vertical inner face traverse provided all-round. In some cases when the force of explosion can be safety and easily let off through one side, one of the four walls may be very weak. Examples are nitration buildings with the weak side facing an hill slope or forest and detonator press cubicles with back side open. The strong roof intercepts missiles from another exploding building, which ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 307 may otherwise be falling through the roof initiating an explosion. The RCC slab roof also can come down and smoother the effects of explosion when the same takes place dislodging and breaking the walls. (b) Doors—Process buildings should have easily accessible doors opening outwards except in case of non- manned remote controlled rooms. Each process building shall have adequate number (minimum 2) of exits for quick escape of personnel in the event of a mishap. The doors should be of wood painted with a suitable fire resistant paint. (c) Windows—ventilators: Number and size of windows and ventilators shall be decided on the basis of actual requirements. Frames may be of steel or wood. No exposed iron or steel is allowed. It should be either galvanized or adequately covered with paint. Iron frames is not preferred where acid fumes are likely to corrode or explosive dust may accumulate in cracks and crevices. The glass panes for the windows and ventilators should be wired glass type. (d) Surface and finishing—The floor, wall and ceiling should be finished smooth and free from cracks and crevices. Depending on the nature of chemicals handled, special protection on floor and lower wall may be necessary. Mastic floor or antistatic rubber matting on floor is essential in some cases. In chemical plants the drains for taking out liquor and washing shall have chemical resistant plastic or mastic lining. 2.Traverses A Types of traverses: The most commonly used traverses are natural angle traverse (NAT) of earthen mounds for storage buildings and vertical inner face traverse (VIFT) for process buildings. The traverses should be at least 2.4 metres wide at the explosives stack level. The minimum width at the top is 1.5 metres for VIFT and 1 metre for NAT, the top being at least 0.6m above the explosives stack level. The tow of the traverse should not be more than 1 to 1.5 metres away from the building to be protected. If more clearance becomes essential, the height of the traverse is to be increased proportionately maintaining the same angle of protection. The inner face of the VIFT is a vertical masonry wall, strong enough to bear the load of the earth filling at the back. A semi VIF traverse is similar to VIFT except that above the stack level, the inside surface is inclined and not vertical reducing the top thickness to 1 metre. B. Sectional view showing types of traverses : The construction of the buildings and traverses are required to be strictly as per the specifications. There is no scope for any compromise in the material and dimensions. RCC roof or wall with reinforcement only for namesake, a traverse located at 5m or farther from the building or a VIFT with little earth behind the vertical wall serve no purpose. C. Internal Wall as Traverse: Buildings handling small quantity of explosives can be effectively traversed by its own walls of adequate construction. The following table shows the recommended wall thickness for different quantities of explosives. Weight of explosives RCC wall (preferred thickness) Brick wall thickness kilogrammes millimetres millimetres 5 225 340 7 225 450 12 225 570 18 300 700 35 450 Not permitted 50 600 Not permitted f 308 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] D. Partition Walls : A processed building having several rooms or compartments can have partition walls of adequate dimensions and constructions. Such walls can delay substantial transmission of explosion from one side to the other side of the wall, thus preventing simultaneous detonation. The wall thickness for different quantities of explosives are given in the table below:— Weight of explosives in Wall thickness in centimetres for preventing of reinforcement by volume* kilogrammes 0.20% 0.5% 0.7% 0 - 75 10 10 10 >75-100 15 15 10 >100-150 20 20 15 >150-200 25 25 20 >200-250 30 25 25 >250-300 30 30 25 >300-350 35 35 30 * The wall if made of brick should be twice the thickness of RCC wall with 0.2% reinforcement. The safety distance of such a process building having rooms or compartments separated by partition walls as above can be based on the explosive content of any of the compartment, which is the largest. 3. Explosive Limit—Person Limit: Limiting the quantity of explosives handled in a building and the number of persons employed therein are obviously to reduce the adverse effects of an explosion. It is desirable that the minimum quantity of explosives and the minimum number of persons absolutely necessary for an operation or process should only be allowed in the relevant building from the point of view of safety. The recommended limit on quantity of explosives and number of persons shall also depend on the sensitivities and properties of explosives handled. In case of sensitive initiating explosives the limits should be as low as possible. For keeping the reasonably low, it may be necessary to divide an operation into several sub-operations in different buildings. Specification—2: Specifications of magazines other than that of fireworks 1. General : The basic considerations in the construction of magazines are security to ensure that the contents are kept out of the hands of unauthorised persons, to maintain them in good conditions and to reduce the risk of accidental explosion. This calls for a construction, which will resist illegal entry as much as possible and is well ventilated. In choosing a site for a magazine, consideration should be given to protection of life and property offered by natural features of the ground in the event of a fire and/or an explosion. The suitability of a site and the amount of explosives that may be stored are determined by its distance from public thoroughfares; residential or industrial areas, railways etc. as specified in the table of safety distance in Schedule VIII. Naturally a site obscured from public view either by natural or artificial means is preferred. Apart from the rules and regulations concerning the storage of explosives, certain conditions should be observed from the point of view of care for the materials concerned for example, improper storage may lead directly to misfires later on. In all cases, places of storage should be dry, well ventilated and protected from extremes of temperature as much as possible. Stocks should be drawn upon in strict rotation. Any surplus from the day's work being returned to the magazine should be kept separately for use on the following day. Safety Fuse and detonators should be kept in perfect condition for obtaining good results. Therefore, at all times during transport, handling and storage, they should be protected from moisture and contact with oil, grease, kerosene or other liquids. Detonators shall not be stored with other explosives. 2. Materials of construction of magazine : Magazines may be of heavy construction, i.e. steel, reinforced concrete, brick, stone or preformed concrete blocks. Maximum security is attainable only with steel or reinforced concrete structures. The internal dimensions of the magazine shall be such that there is ready access to all explosives. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 309 3. Construction of the magazine : A magazine shall be well and substantially and shall be made and close so as to prevent unauthorised persons from having access thereto and to secure it from danger. Magazines can be of the following types: *Type 'A' magazine: Type 'A' magazine shall be of a type approved by the Chief Controller and shall primarily have the following - (a) Walls of reinforced concrete at least 225 millimetres thick or brick or stone at least 450 millimetres thick set in cement mortar. Concrete shall have a minimum compressive strength of 2,500 lb/sq.inch at 28 days (the required strength will be reached by a mixture consisting of 1 part cement, 1-½ parts sand, 3 parts of aggregate by volume). Reinforcement should consist of square mesh, hard-drawn steel wire fabric, providing a cross-section area in each direction of not less than 0.21 sq. inch of 2 ft. of wall. The reinforcement shall be covered by not less than 50 millimetres of concrete on either side. The bricks and concrete blocks shall conform to relevant Indian Standard Specifications. Commercial grade steel is satisfactory for use in construction. The cement mortar shall consist of not less than one part of cement and three parts of clean sand. (b) Interior, and the benches, shelves and fittings therein shall be so constructed or so lined or covered as to prevent the exposure of any iron or steel and the detaching of grit, iron, steel or similar substances in such manner as to come into contact with explosives. Such interior benches shelves and fittings shall be kept free from grit and otherwise clean; and in the case of any explosive that is liable to be dangerously affected by water, due precautions shall be taken to exclude it therefrom. (c) Roof shall be of reinforced concrete at least 150 millimetres thick. (d) One ventilator at the top and bottom in each opposite side wall of the magazine shall be provided where the weight of explosive stored is up to and including 500 kilogrammes and minimum two in the top and bottom of each wall shall be provided where the weight of explosive stored exceeds 500 kilogrammes. Number of the ventilators may be increased as desired by the licensing authority. The ventilators shall be 22.5 centimetres x 11.25 centimetres. Z type fitted with frame of iron bars set firmly in the wall on the outer face, the bars to be of 2.35 square centimetres, (3/8" sq.) iron set angle-wise with the frame. The inner opening to be protected with brass wire gauge of 3 meshes per centimetre. (e) External doors — (i) that opens outwards and when closed fit tightly; (ii) to be constructed of steel plate at least 5 millimetres, thick with or without internal lining of wood. (f) Every internal door — (i) made of wood; (ii) locks and fittings of non-ferrous metal. (g) External door-locks should be of "dead lock" type. (h) A separate room for storage of detonators or other explosives of Class 6 Division 3 if stored within the magazine. Such room shall have independent entrance and a minimum air-gap of 1 metre from any other room in the magazine and the thickness of the wall of the detonator storage room facing any other room in the magazine shall be minimum 60 centimetres. (i) Wooden trestles or raised cement platform for storage of explosive packages. (j) A porch if necessary shall be (i) of the same construction as the remainder of the magazine; and (ii) used only for keeping all tools or implements used in connection with the magazine or the changing of clothe and shoes. (k) 25 x 50 mm furring strips fastened to the wall, vertically on 300 millimetres centres starting 130 millimetre from floor and continuous to the stacking line, around the usable portions of the walls to provide air circulation and to prevent cases of explosives being stacked directly against the walls. (l) A minimum 12 millimetre red line painted on the interior walls of the magazine at a height of 2.5 metres from the floor level. This line indicates the maximum height to which explosives may be stacked. The licensing authority may specify lower stacking height if deemed necessary. (m) An internal volume not less than 0.4 cubic metre for each 100 kilogrammes of explosives. In addition sufficient space shall be provided for passage between stocks of packages if required by licensing authority. 310 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (n) Sufficient number of windows for proper lighting inside the magazine. The windows shall open outside and constructed of steel plate at least 5 millimetre thick with or without internal lining of wood. Type 'B' magazine (portable magazine): Type 'B' magazine shall be of a type approved by Chief Controller and shall primarily have the following — (a) Walls of steel plate at least 5 millimetres thick; (b) A roof of steel plate at least 5 millimetres thick; (c) Interior lining at least 10 millimetres thick on walls, doors and ceiling and 25 mm thick on door and consisting of closed fittings boards or wood joined together by tongue and groove joints in such a way that no iron or steel is exposed on the interior sides, ceiling, floor or doors; (d) An internal volume not less than 0.4 cubic metre for each 100 kilogrammes of explosives. The maximum internal volume shall not be more than 2 cubic metres. (e) Ventilation by means of vents which shall be adequately protected; (f) External hinges of steel welded to the door and to the frame of the magazine; (g) A lock of "dead lock" type for external door. Type 'C' magazine (small brick cement magazine for storage of explosives up to 100 kilogrammes and one box of detonators): Small brick cement magazine shall primarialy have the following: (a) The magazine shall be constructed of brick masonary or cement concrete on plinth 1 metre above ground level with 45 centimetres thick walls and 15 centimetres thick RCC roof. (b) The detonator room and high explosives room shall be at 1.5 metres separation distance as per the sketch. (c) The magazine rooms shall be fitted with steel doors of thickness not less than 5 millimetres, opening outside with efficient locking arrangements. (d) The rooms shall have one Z type ventilator fitted with frame of iron bars set firmly in the wall on the outer face, the bars to be of 2.35 square centimetres, (3/8 square inch) iron set angle wise with the frame. The inner opening should be protected with brass wire gauge of 3 meshes per centimetre. (e) The magazine shall be fitted with lightning conductor as per IS 2309. Specification 3: Specification of fireworks manufacturing factory and store house and magazine for fireworks or safety fuse 1. Manufacturing factory for fireworks: A. Mixing / Filling building: The basic consideration in construction of a mixing/filling building is to ensure safe handling, good maintenance and upkeep, to reduce the risk of fire, friction or impact and to minimize the loss of lives in case of accidents. The building shall be provided with adequate number of doors. The place of mixing/filling shall be dry. The mixing/filling building should have walls built of brick, stone or concrete. The bricks and concrete shall conform to relevant Indian Standard Specifications. The cement mortar shall consist of not less than one part of cement and three parts of clean sand. The interior of the mixing/filling building shall be kept clean and shall as far as practicable be kept free from grit. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 311 Mixing/filling building shall have : (a) wall constructed of brick and cement to a thickness of 34 centimetres and the roof to a thickness of 15 centimetres of RCC . (b) blast wall of 34 centimetres thick constructed of brick and cement or 23 centimetres of RCC in front of doors at a distance of 1 to 2 metres. The blast wall shall be 0.5 metre wider than the door opening on both sides and shall have a height of 2 metres. (c) an explosives limit of 5 kilogrammes for white powder rooms and 12.5 kilogrammes for black powder rooms and the man limit shall be 2 numbers. (d) three or four doors in two walls. (e) doors made of wood or wooden frame lined with aluminium sheet of suitable thickness and shall be fitted with non-ferrous hinges. (f) doors that open outwards. (g) its locking system provided from outside only. (h) floor covered with non-sparking and non-conducting rubber sheet. (i) lightning conductor provided as per IS 2309 of 1969 if mixing / filling is done by electrically operated machine. B. Manufacturing / Process Sheds: a. The manufacturing/process shed shall be situated at ground level, with walls built of brick or stone with cement, or of concrete. The bricks and concrete shall conform to relevant Indian Standard Specifications. b. The walls shall be of 23 centimetres thick with cement and brick or of 15 centimetres thick RCC. c. The roof shall be of G.I. sheets or 10 centimetres thick RCC. d. Four doors shall be provided. e. The doors shall be made of wood or of wooden frame covered by G.I. sheet, fitted with non-ferrous hinges or with ferrous hinges so lined or painted as to prevent the exposure of any iron or steel. f. The doors of different process buildings shall not face each other. g. If doors of adjacent sheds face each other, a screen wall of brick and cement to a thickness of 23 centimetres shall be provided at a distance of 1 to 2 metres from the door. h. All the doors shall open outwards. i. The shed shall have a floor area of minimum nine square metres. j. The shed shall have a floor of smooth finish. C. Blast wall: The blast wall shall be built of bricks, stone or concrete. The bricks and concrete shall conform to relevant Indian Standard specifications. The cement mortar shall consist of not less than one part of cement and three parts of clean sand. The blast wall shall be constructed at a distance of one to two metres from the door or from the boundary wall of the building. The height of the blast wall shall be 2 metres and the width shall be 0.5 metre wider than the door opening on both sides. The blast wall shall be provided around mixing and filling sheds which have the approved explosive limit of 5 kilogrammes and approved man limit of 2. The licensing authority may specify higher height of blast wall if deemed necessary. The thickness of the blast wall shall be decided in accordance with the licensed limit of the building and the materials used in its construction, as specified in the table appended below : Quantity of explosives in kilogrammes Thickness of wall in centimetres not exceeding RCC Brick 2.5 23 34 5 23 34 7 23 45 12 23 57 18 30 60 35 45 70 50 60 75 312 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] D. Drying Platform: The basic considerations in the construction of drying platform are to ensure that the fireworks items are dried securely by keeping them out of reach of persons engaged in other activities and to prevent any grit, dust or moisture from coming into contact with the fireworks. The drying platform shall always be kept dry. The drying platform shall have a platform of bricks, stone or concrete with a floor area of minimum 9 square metres to a maximum of 15 square metres. The height of platform shall be 1 to 1.5 metres. The bricks and concrete shall conform to relevant Indian Standard Specifications. The cement mortar shall consist of not less than one part of cement and three parts of clean sand. However, drying platform used for drying of sparklers may have a floor area on the ground filled with sand and lined with bricks or a floor area spread on the ground with stone jelly and cement. Where any platform is located directly in the line of the door of any process building, a blast wall in front of such door of the said building shall be provided as per specification 6 attached to this schedule. In case where drying platforms lie adjacent to each other, a blast wall shall be constructed in the intervening space at 1 to 2 metres away from any one of such platforms lying adjacent to each other. In the case of a fuse cutting-cum-drying platform, such platform may be built at a distance of 18 metres from process buildings and shall observe an outer safety distance of 45 metres. Such drying platform shall have a screen/blast wall at a distance of 1 to 2 metres from the platform, with a height equal to half of the length of the side perpendicular to the screen wall/blast wall. The construction of the screen/blast wall shall be as per specification 6 attached to this schedule. A temporary roof may be provided by erecting 4 pillars or poles if necessary for protection from direct sunlight. E. Transit building : The basic considerations in construction of a transit building are to ensure that the contents are kept out of the hands of unauthorised persons, to maintain them in good condition and to reduce risk of fire. This calls for a construction which will resist illegal entry as much as possible and be well ventilated. The place of a storage should be dry and it should be possible to draw stocks in strict rotation. The transit building should have walls built of brick, stone or concrete. The bricks and concrete shall conform to relevant Indian Standard Specifications. The cement mortar shall consist of not less than one part of cement and three parts of clean sands. The interior of the transit building shall be kept clean and all benches, shelves and fittings shall be so constructed or so lined or covered as to prevent the exposure of any iron or steel and the detachment of any grit, iron, steel or substances shall be in such manner as not to come in contact with the materials stored and such interior, benches, shelves and fittings shall as far as practicable be kept clean and free from grit. (a) It should have a cement brick wall of 45 centimetres thick and RCC roof of 15centimetres thick. (b) The transit building shall have adequate number of ventilators as desired by the licensing authority. The ventilators shall be provided at the top and the bottom of the walls as suggested by the licensing authority. The ventilators shall be 22.5 centimetres x 11.25 centimetres fitted with suitable frames firmly set in the walls on the outer face. The bars shall be of minimum 2.35 square centimetres set angle-wise with the frame. The inner opening shall be protected with wire gauge of minimum 3 mesh per centimetre. (c) Only one door shall be provided. (d) The door shall be made of wood fitted with non-ferrous hinges. (e) The door shall open outwards. (f) If the door faces the drying platform or the door of any other process building, a blast wall (34 centimetres brick cement or 23 centimetres RCC) in front of doors at a distance of 1 to 2 metres. The blast wall shall be 0.5 metre wider than the door opening on both sides and shall have a height of 2 metres. (g) That transit building may not be provided with lighting conductor unless otherwise specified by the licensing authority. 2. Magazine for storage of fireworks or safety fuse: The basic considerations in construction of a magazine are to ensure that the contents are kept out of the hands of unauthorised persons, to maintain them in good condition and to reduce risk of fire. This calls for a construction which will resist illegal entry as much as possible and is well ventilated. The place of a storage should be dry and it should be possible to draw stocks in strict rotation. The magazine should have walls built of brick, stone or concrete. The bricks and concrete shall conform to relevant Indian Standard Specifications. The cement mortar shall consist of not less than one part of cement and three parts ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 313 of clean sands. The interior of the storehouse shall be kept clean and all benches, shelves and fittings shall be so constructed or so lined or covered as to prevent the exposure of any iron or steel and the detachment of any grit, iron, steel or substances in such manner as not to come in contact with the materials stored and such interior, benches, shelves and fittings shall as far as practicable be kept clean and free from grit. a. The magazine shall have adequate number of ventilators as desired by the licensing authority. The ventilators shall be provided at the top and the bottom of the walls as suggested by the licensing authority. The ventilators shall be 22.5 centimetres x 11.25 centimetres fitted with suitable frames firmly set in the walls on the outer face. The bars shall be of minimum 2.35 square centimetres set angle-wise with the frame. The inner opening shall be protected with wire gauge of minimum 3 mesh per centimetres. b. The magazine shall have a minimum 12 mm red line painted on the interior walls at a height 3 metres from the floor level. This line indicates maximum height to which explosives may be stacked. The gang way space of minimum 30 centimetres shall be provided around the usable portion of the walls to provide air circulation. In addition sufficient space shall be provided for passage between the stacks of packages if required by the licensing authority. The licensing authority may specify lower stacking height if deemed necessary. c. The magazine shall have sufficient number of wooden windows for proper lighting inside. The windows shall open outwards. d. The magazine shall have external doors that opens outwards and when closed fit tightly to be constructed of wood with or without lining of steel plate. e. The magazine shall have smooth, stone or cement flooring. f. The roof of the magazine may be made of G. I. sheet or A.C. sheet. g. The magazine shall have a floor area of 2 square metres per tonne of fireworks or 10,000 metres of safety fuse. h. The magazine shall have a floor area of 16 square metres per tonne of paper caps or amerces. i. The magazine shall have a floor area of 8 square metres per tonne of serpent egg. j. The paper caps or amerces or colour matches which contain chlorate may be kept under this store house shall be separated by an intervening partition wall made of brick, stone or concrete to prevent explosion or fire in the one communicating with the other. k. The magazine shall be fitted with lightning conductor as per IS 2309. 3. Store House for fireworks : (1) The storehouse shall be single storied building with 23 centimetres thick walls built of brick or stone mortar, or concrete and roof of 15 centimetres thick RCC. (2) The storehouse shall maintain open safety distance of 3 metres on all sides, which shall be protected by 1.8 metres high boundary wall or fencing. (3) The storehouse shall have a floor area of not less than 12 square metres and not more than 40 square metres for storage of fireworks. (4) The door of storehouse shall be made of wood or other suitable materials and open outwards. If shutter door is provided, there shall be hinges provided at the top of the shutter door to lock the shutter leaf in open position. Specification 4: Specification for a road van for carriage of explosives. Part - I (General) : (1) Air space between body and cab. - A clear space of at least fifteen centimetres shall be left between the body and cab. (2) Driver's cab.—The cab shall be fitted and covered externally with 0.914 millimetres aluminium sheeting. The wood if used shall be treated as to render it non-flammable. (3) Cab-doors shall be fitted having windows of non-splinter type glass. (4) Wind screen.—A substantially framed wind-screen shall be fitted with the portion in front of the driver's seat pivoted on strong brass quadrants for opening. 314 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (5) Fuel tank.—The fuel tank (petrol) shall be in front of the fire screen described under item (11) below. It should be so located as to minimise the possibility of its being damaged should the vehicle be involved in an accident Steel guards should be provided if required by approving authority. (6) Fuel cut-off.—A quick acting cut off (for petrol lines) shall be fitted on the feed pipe in an easily accessible position and shall be capable of being operated without the necessity of lifting the bonnet and shall be so located as not to be involved in a fire in the engine. (7) Exhaust pipe and Spark Arrestor.—The whole of the Spark Arrestor and exhaust piping shall be in the front of the fire-screen described in item 11. (8) Fire extinguisher.—Two chemical fire extinguishers of minimum 2 Kilogrammes shall be provided. The fire extinguisher should be capable of dealing with petroleum fire. (9) Self Starter.—A self starter shall be provided. (10) Lighting.—Electric head, side and tail lamps shall be provided and shall be operated from the dash board. All electric wirings and battery cables shall be fully enclosed and maintained in good operating condition. (11) Fire Screen.—Shall consist of only ply asbestos and 18 gauge steel sheets fitted to the whole of the driver's cab and extending to within 300 mm of the ground. The part extending from bottom of the cab to within 390 mm of the ground shall be carried on an iron angle frame of light construction. (12) Body.—A body conforming to the second part of this specification shall be fitted. (13) Spare Wheels.—One spare wheel inclusive of outer cover and inner tube shall be carried for each size of wheel on the chassis. (14) Painting and Marking.—Body and cab shall be painted and marked and lined with a colour approved by the licensing authority. The van should be painted with aluminium or white paint. The letter 'E' should be written prominently on the sides and rear of the van. The name and address of the licensee and the licence number should be written in small letters on one side. Vehicles holding inter-state or national permits shall be painted as per directions of Road Transport Authority. However, another circle of 60 centimetres diameter in red colour should be painted on one of the flaps of rear door of van with letter 'E' inscribed in the circle. (15) Total maximum load.—The total maximum load for a vehicle shall be equal to or exceed gross vehicle weight rating. (16) Inspection.—The whole of the work shall be to the satisfaction of the licensing authority who shall have free access at any time to the workshop fabricating the body and who may reject any material or workmanship which does not comply with this specification. Part - II : (1) The body framing is to be constructed of best selected, teak thoroughly seasoned and free from all defects. All joints are to be morticed and tenoned or half checked, depending upon their position in the structure, and securely fixed with screws. The joints are to be coated with white lead before assembly. All parts of the framing, which will be in contact with the outer metal panelling, are also to be thoroughly coated with which lead before panelling is fixed thereto. Iron plates, knees, etc., may be used for stiffening the framing where they are considered necessary, but no such iron work must be exposed in the interior of the completed van body. (2) Flooring.—This is to be constructed of teak boarding tongued and grooved 22.2 millimetres, thick and about 152.4 millimetres or 177.8 millimetres in width. It is to be recessed into the soleplate of the van body and below it is to be fixed a sheet of 0.914 millimetres (20 S.W.D.) aluminium sheet. The flooring is to be supported by bearers about 28.6 millimetres thick by 50.8 millimetres wide, fitted between the soleplate and screwed on the top of the cross-members of the chassis frame. The sill of the doorway has to have a fall outwards of 6.4 millimetres and it should be covered with a brass plate full width of the doorway, 63.5 millimetres wide inside, and having its outer edge turned downwards, and secured in position with brass screws. (3) Body panelling and lining.—The roof, floor, sides, ends and doors of the van are to be covered externally with .014 millimetres (20 S.W.G.) aluminium sheeting and inner lining may be of asbestos or wood so treated as to be rendered non-flammable or with such other material as may be approved in writing by the licensing authority. This must have a smooth surface, free from distortion or any dents, and it is to be fitted to the framing in sections of convenient size. The roof beading is of aluminium 19 millimetres × 4 millimetres and ends to a distance of 25.4 millimetres the end turnover, being relieved at intervals of 152.4 millimetres to allow ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 315 the sheeting to lie flat on the framing. At all places where sheeting is fixed to the body framework, it has to be covered by a beading. The roof beading is of aluminium 19 millimetres x 4 millimetres whilst a wooden weather beading is run round the sides and ends where the joint with roof sheeting takes place. At other places aluminium leading 19 millimetres x 4 millimetres has to be used, excepting only the bottom joint of the sides which is covered by a wooden rail 25.4 millimetres wide 38.1 millimetres deep, and the central cover joint of the doors, which is formed with flat mild steel strap 38.1 millimetres wide. The interior of the van body has to be lined with 20 S.W.G. aluminium sheeting throughout, sides end, roof and doors, the lining has to be fitted in as few sections, as possible and in all cases brass screws must be used for securing same. (4) Doors.—Double doors are to be fitted at the rear ends of the body and they are to be a close fit all round the framing, panelling and lining of same being similar in all respects to the body works. They are to be levelled along the bottom to make a watertight joint with the brass covered still of the doorway, and the central joint of doors must also bevelled and covered with stapping as previously mentioned. The doors are to be hung on strong mild steel crook and bank hinges. The band section being 29.7 x 8 millimetres and these in turn are to be securely fixed to hinge and angle plates of section 44.4 x 8.0 millimetres on the rear frame posts of the van body. The hinges are to be so constructed and set that the doors will swing right round against the van body side, and facilities are to be provided for fixing the doors in this position. A slot is cut in the clip and for the reception of a brass H. & T.V. padlock on the left-hand side of the doors. There shall be no opening in the body of the vehicle except through the doors at the back. No holes shall be drilled in the chassis, unless allowed by the maker for the purpose of securing the van body. (5) Body dimensions.—The inside dimensions of the body shall be suitable for the quantity of explosives proposed to be carried. The body shall be of such dimensions and fitted in such a manner as to keep the vehicle stable during transport of explosives. Specification 5: Type A - Specification for compressor mounted motor truck or tractor for possession and transport of explosives (1) A Compressor mounted tractor intended for possession and transport of explosives for well sinking shall have the compressor securely fixed with the tractor chassis. (2) The fuel tank, additional fuel tank and exhaust shall be placed in front of the driver's seat. (3) At the back of the driver's seat and on the top of the compressor unit, a securely fixed platform for housing the boxes of explosives shall be provided. The platform shall maintain a minimum clearance of 15 centimetres from the driver's seat horizontally, and from all pressure parts of the compressor vertically. Provision for placing air intake tube and filter below the platform may be made. (4) Two separate wooden boxes with locking arrangements for keeping high explosives and detonators shall be provided. The box for high explosives shall be of adequate dimensions to accommodate 25 kilograms package of explosives and 100 meters detonating fuse. The box for detonators shall be of adequate dimensions to accommodate 200 numbers ordinary or electric detonators and shall have internal thermocole lining. Empty space in the detonator box shall be packed with pieces of thermocole to prevent movement of detonators during transport. (5) Two separate steel boxes of the type approved by the Chief Controller of Explosives for keeping the above wooden boxes containing high explosives and detonators shall be securely fixed on the platform with a minimum clearance of 1 meter between the boxes. These boxes shall be made of at least 3 millimetres thick steel sheet. The steel box for keeping wooden box containing high explosives shall have a small compartment for keeping safety fuse. Both these fixed steel boxes shall have side doors fixed with hinges covering full length of the box and shall be provided with locking arrangement. (6) A vertical screen wall made of at least 6 millimetres thick steel sheet shall be securely fixed to platform behind the driver's seat covering the length of the platform and height of the steel boxes. (7) The drilling rods and other tools shall be kept in fixtures or boxes fitted in any place in front of the vertical screen wall behind the driver's seat. (8) One dry chemical fire extinguisher of minimum 2 kilograms capacity shall be provided. (9) Two separate steel boxes of the type approved by the Chief Controller of Explosives for keeping the above wooden boxes containing high explosives and detonators shall be securely fixed on the platform with a minimum clearance of 1 metre between the boxes. These boxes shall be made of at least 3 millimetres thick steel sheet. The steel box for keeping wooden box containing high explosives shall have a small compartment for keeping safety fuse. Both these fixed steel boxes shall have side doors fixed with hinges covering full length of the box and shall be provided with locking arrangement. 316 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Type B - Specification for a motor truck for carriage of explosives together with compressor unit. (1) A clear air space of at least fifteen centimetres shall be left between the body and the cab. (2) The deriver's cab shall be fitted and covered externally with .914 metre (20 S.W.G.) aluminium sheeting. (3) The cab doors shall be fitted having windows of non-splinter type glass. (4) A substantially framed windscreen shall be fitted with the portion in front of diver's seat pivoted on strong brass quadrants for opening. (5) The fuel tank shall be below the floor level and at least 0.5 metres from the boxes carrying explosives. It should be so located as to minimise the possibility of its being damaged should the vehicle be involved in an accident. (6) A quick acting cut off (for petrol lines) shall be fitted on the feed pipe in an easily accessible position and shall be capable of being operated without the necessity of lifting the bonnet and shall be so located as not to be involved in a fire in the engine. (7) The Spark arrestor and exhaust piping shall be below the cab and shall not be below the body. (8) A chemical fire extinguisher of minimum 2 kilogrammes shall be provided. The fire extinguisher should be capable of dealing with petroleum fires. (9) A self-starter shall be provided for the engine. (10) Electric head, side and tail lamps shall be provided and shall be operated from the dashboard. Electric troches (dry cell type) may be carried for use for lighting during emergency. (11) One spare wheel inclusive of outer cover and inner tube shall be carried for each size of wheel on the chassis. (12) No holes shall be drilled in the chassis unless allowed by the maker for the purpose of securing body. (13) The flooring is to be constructed of teak boarding tongued and grooved at least 21 millimetres thick and about 150 millimetres or 175 millimetres in width. (14) Base of the compressor should be minimum 150 millimetres high from the floor or the truck body. (15) A mild steel tray shall be provided underneath the compressor and shall be of such size and placed in such a way that all the oil dripping from the compressor shall fall in the tray. (16) The exhaust pipe of the compressor shall face away from the boxes carrying explosives and shall be fitted with an efficient spark arrestor. (17) Only approved type of boxes will be used for carrying explosives and such boxes shall be firmly fixed to the body in such a way that there is no movement of the boxes when the truck is in motion. The empty space in the detonator box shall be filled with thermocole pad, foam pad or other similar suitable material to protect movement of detonators during transport. (18) Not more than two boxes for carrying explosives shall be fitted to any truck. One of the boxes shall be used for carrying high explosives and the other for detonators. The boxes shall be fixed in such a way that their doors do not open face to face. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 317 (19) The distance between the explosives boxes shall be minimum 1,000 millimetres. The distance between the compressor and the explosives boxes shall be minimum 1500 millimetres. (20) A suitable fire screen shall be provided between the cab and the boxes carrying explosives. (21) A suitable asbestos or G.I. sheet screen shall be provided between the explosives boxes and the compressor leaving adequate space for movement of operator for removing explosives from boxes. (22) The space between the fire screen under clause 20 and the asbestos screen under clause 21 above shall be suitably covered so as to protect from weather. (23) Not more than 25 kilogrammes of high explosives, 200 numbers of detonators and 200 metres of safety fuse shall be carried in the truck. (24) The detonator box shall be fixed away from the battery side and the battery shall be carried in the cab below driver's seat. Specification 6: Specification of metal cases for conveyance of explosives Type A — General : The body to be of wrought iron, mild steel, hard rolled brass, muntz metal, or zinc, riveted or welded, fitted at both ends with a substantial flange of same materials or of gunmetal for the attachment of lid and bottom; if of iron or steel to be thoroughly galvanised after making up or to be effectively painted. Thickness shall not be less than 1.257 millimetres (18 BG - .0495 inches) or, if of zinc, not less than 9.5 millimetres. The bottom to be of same materials as body or of gunmetal; if of iron or steel, to be thoroughly galvanised, securely riveted to flange of body or forming part of such flange. Thickness not less than 3.2 millimetres or of zinc not less than 9.5 millimetres. Alternatively the bottom may be made of mild steel of 4.8 millimetres thick, thoroughly galvanised and dished so that fits tightly over the body made of mild steel as above but without a bottom flange. The body to project at least 25.4 millimetres into the dished bottom and the edges of the dished end and of the body to be welded continuously to the body and to the bottom of the dished end respectively. The lid to be of same materials as body or of gunmetal; if of iron or steel, to be thoroughly galvanised. Thickness not less than 1.6 millimetres at centre, and not less than 3.2 at rim, or if of zinc, not less than 9.5 millimetres throughout. The lid to be secured by not less than four good screws, bolts or swing bolts, with or without a substantial hinge, which may take the place of one of the four screws, bolts, or swing bolts. A washer of leather, India rubber or other suitable material to be between the lid and the flange, unless the lid is fitted with a projecting ring into a depression in the flange. All rivet heads to be well finished, and the inside of the package to be free from rough edges or burrs. The whole to be of good material and workmanship and to be maintained in a efficient condition. Type B— Duralumin Containers : Dimensions of container inside to be 902 millimetre. Deep by 308 millimetre wide by 267 broad. The body of container to be of 1.626 millimetre (No.16 S.W.G.) sheet in one piece riveted with 8.00 millimetre (5/6ths inch) diameter rivets 25.4 millimetre pitch at seam. 50.8 millimetres pitch at other three corners, having 31.8 m. by 31.8 by 4.8 millimetre angle riveted on top and round bottom with 8 millimetre diameter rivets 25.4 pitch. Bottom of containers to be of 3.25 millimetres ( No. 10 S.W.G.) sheet fitted with 31.8 millimetre by 31.8 millimetre by 4.8 angle all round and riveted with 8 millimetre diameter rivets. Corner pieces 2.642 millimetres (No. 12 S.W.G.) sheet to be riveted to angle and to bottom plate with 8 millimetres diameter rivets. Cover of container to be of 2.032 millimetres (No. 14 S.W.G.) sheet fitted with 37.6 millimetre by 25.4 millimetre by 4.8 millimetre angle all round and riveted with 8.0 millimetre diameter rivets. Corner pieces 2.042 millimetre (No. 12 S.W.G.) sheet to be riveted to angle and cover plate with 8.00 millimetre diameter rivets. Cover to be fastened to container by four 12.7 millimetre with worth set pins with washer. Rubber joint 31.8 millimetre by 3.2 millimetre thick to be riveted to underside of cover plate by twelve 6.3 millimetre diameter rivets, 15.9 millimetre diameter holes to be bored in cover and joint to suit 12.7 millimetre set pins. Two Duralumin drop down handles to be riveted to body of container. 318 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Type C - The body to be of wrought iron or mild steel, thoroughly galvanised, thickness not less than 18 B.G. (0495 inch) fitted at the top with a flange 12.7 millimetre thick made of the Aluminium Alloy (12.5 percent to 14.5 percent zinc; 2.5 percent to 3 percent copper; remainder Aluminium). The bottom to be of the Aluminium Alloy, not less than 12.7 millimetre thick at the rim, and not less than 4.8 millimetre thick at the centre, and provided with a protection 25.4 millimetre high and at least 6.3 millimetre thick, so made as to be a close fit inside the body, to which it shall be riveted with rivets 6.3 millimetre diameter. The lid to be of the Aluminium Alloy, not less than 12.7 millimetre thick at the rim and not less than 6.3 millimetre thick at the centre and secured by eight screwed studs to the flange. A washer of leather India rubber, or other suitable material shall be between the lid and the flange unless the lid is fitted with a projecting ring fitting into a depression in the flange. All rivet heads to be well finished and the inside of the package to be free from rough edges or burrs. Specification 7 : Specification of BMD vehicle The Bulk Mixed Delivery Vehicle normally called as BMD vehicle is specially designed for carrying non-explosive matrix along with other ingredients like Ammonium Nitrate, gassing agent etc. in separate containers mounted on a vehicle chassis to the blasting site. The vehicle also has a water tank, control panel, hydraulic oil tank, radiator, hose reel with pump, hydraulic pump, product pump, air receiver, gassing agent pump, water pump and a drivers cabin mounted on the chassis. The mounting of various containers on the chassis is done in such a way that the vehicle is stable during movement both in empty and laden condition. BMD vehicle shall meet the following requirements:— (1) The vehicle must be in good mechanical condition and all the tanks and other equipments mounted there on shall be properly secured to the vehicle to avoid any damage during movement of the vehicle. (2) The vehicle must be strong enough to carry a load without difficulty and be constructed of non-combustible materials, compatible to the ingredients and /or premix, to be contained or transported . (3) There shall be separate compartment for each ingredient or premix, each provided with separate means of filling and discharge so as to eliminate possibility of accidental mixing of ingredients during transit or otherwise. The compartment containing liquid shall be provided with shut-off valve. (4) No parts of the equipments and fittings shall be projected outside the vehicle. (5) The vehicle shall be provided with means and mechanisms for controlling and monitoring various essential parameters like temperature, flow , density and the control panel displaying the status of above parameters and control switches shall be located in a conspicuous position visible and accessible to the operator. (6) The cabin of the vehicle shall be provided with non-splinter type glass. (7) The vehicle shall be provided with essential tools secured in a box. (8) All moving parts of the mixing system must be designed to prevent heat build up. (9) Shafts or axles which contact the product must have outboard bearings with a minimum of one-inch clearance between the bearings and the outside of the product container. Special attention must be given to the clearances on all moving parts. (10) When electrical power is supplied by a self-contained motor-generator located on the vehicle, the generator shall be separated from the discharge point of the explosives. The generator or the battery shall be provided with a cut-off switch in a readily accessible position. (11) Wiring shall be so fixed and protected so as to minimise accidental damage or undue wear. (12) The BMD vehicle body and equipment shall be electrically continuous with the vehicle chassis. The frame of the mixer and all other equipments that may be used shall be electrically bonded. Bonding points and bonding cables for effective grounding shall be provided. (13) During mixing or loading, a positive grounding device and a semi-conductive hose shall be used to prevent accumulation of static electricity. The supervisor shall evaluate all system to ensure that they will adequately dissipate static electricity under potential field conditions. (14) The flexible hoses used to deliver explosives directly in the boreholes shall be electrically and mechanically continuous. ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 319 (15) The exhaust of the vehicle shall be fitted with spark arrestor approved by the Chief Controller. (16) At least two multipurpose fire extinguishers of suitable size and capable of fighting electrical and petroleum fires shall be provided on each vehicle in an easily accessible position. (17) The BMD vehicle shall be marked with the words " BMD vehicle attached to the SMS support plant licence number …..". (18) The name and address of the licensee along with phone number shall also be marked at a conspicuous place legibly for contact in the event of emergency. (19) Fuel cut-off system located in the driver's cabin shall be provided. (20) The ratio of the height of centre of gravity of the vehicle in laden condition to the distances between centres of outer rear tyres shall not exceed 0.9. Typical Sketch of BMD Vehicle Schedule VIII Tables of safety distances The following safety distances shall be observed in the factories licensed for manufacture of explosives or from the magazines licensed for storage of high explosives. If the quantity of explosives to be stored is in between any two stages shown in the table, the safety distance required for higher stage should be observed. Notes : (1) When two or more storage magazines are located on the same property, each magazine must comply with the minimum distances specified from inhabited buildings, railways, and highways, and, in addition, they should be separated from each other by not less than the distances shown for "Separation of Magazines," except that the quantity of explosives contained in cap magazines shall govern in regard to the spacing of said cap magazines from magazines containing other explosives. If any two or more magazines are separated from each other by less than the specified "Separation of Magazines" distances, then such tow or more magazines, as a group, must be considered as one magazine, and the total quantity of explosives stored in such group must be treated as if stored in a single magazine located on the site of any magazine of the group, and must comply with the minimum of distances specified from other magazines, in habited building, railways, and highways. (2) This Table applies only to the manufacture and permanent storage of commercial explosives. It is not applicable to transportation of explosives or any handling or temporary storage necessary or incident thereto. It is not intended to apply to bombs, projectiles, or other heavily encased explosives. 320 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Table - 1 Table of safety distances (in metres) for manufacturing factory, magazine of category "ZZ" Quantity in To and between magazine or To and between To Railway, To Dwelling Houses kilogrammes magazine office etc. process buildings Road etc. offices, factories etc. M UM 50 10 14 18 21 45 100 11 17 21 33 45 150 13 19 24 40 45 200 14 21 26 45 52 300 16 24 30 45 68 400 18 27 34 45 82 500 19 29 37 48 95 600 21 31 42 54 107 700 22 32 45 60 119 800 23 34 49 65 129 1000 24 36 56 74 148 1250 26 39 64 86 171 1500 28 42 72 96 192 1750 29 44 79 106 211 2000 31 46 85 113 226 2500 33 49 97 129 257 3000 35 52 106 142 283 3500 37 55 114 152 304 4000 38 57 122 163 325 4500 40 60 129 172 343 5000 41 135 180 359 6000 44 145 194 387 7000 46 155 206 412 8000 48 163 217 434 10000 52 177 236 471 12500 56 192 255 510 15000 60 206 280 560 17500 63 216 290 580 20000 65 226 303 605 25000 71 244 325 650 30000 75 259 345 690 35000 79 273 365 730 40000 82 285 380 760 45000 86 296 395 790 50000 89 307 410 820 60000 94 327 435 870 70000 99 343 458 915 80000 104 359 480 960 90000 108 373 498 995 100000 112 387 515 1030 112500 116 402 540 1075 125000 120 417 555 1110 136000 124 428 575 1145 150000 128 446 590 1180 175000 135 466 625 1245 200000 141 487 650 1300 ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 321 Table - 2 Table of safety distances (in metres) for manufacturing factory, magazine of category "Y" Quantity in To and between magazines To and between To railway, To Dwelling Houses kilogrammes or magazine office etc process buildings Road etc offices, factories etc. 50 10 12 12 45 100 10 15 15 45 150 10 17 17 45 200 10 19 18 45 300 10 22 21 45 400 10 24 23 45 500 10 26 25 45 600 10 27 26 45 700 10 29 27 45 800 10 30 28 45 1000 10 32 32 46 1250 10 35 33 52 1500 10 37 36 57 1750 10 39 38 61 2000 10 41 40 65 2500 12 44 43 73 3000 13 46 46 80 3500 14 49 48 86 4000 15 51 50 92 4500 16 53 52 98 5000 16 55 54 110 6000 18 58 57 117 7000 19 62 61 123 8000 21 64 63 128 10000 23 69 69 138 12500 26 75 72 149 15000 28 79 78 158 17500 30 83 82 167 20000 32 87 86 174 25000 36 94 93 187 30000 40 100 98 199 35000 43 105 104 210 40000 46 110 108 219 45000 48 114 113 228 50000 51 118 118 236 60000 56 126 128 251 70000 60 132 138 264 80000 64 138 148 276 90000 68 144 158 287 100000 72 149 168 297 112500 76 155 180 309 125000 80 160 192 320 136000 84 165 203 329 150000 88 170 217 340 175000 95 179 242 358 200000 101 195 265 375 322 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Table - 3 Table of safety distances (in metres) for, magazine of category "X"(fireworks) Quantity in To and between magazines To and between To railway, To Dwelling Houses kilogrammes or magazine office etc process buildings Road etc offices, factories etc. 1 2 3 4 5 50 10 10 8 45 100 10 10 9 45 150 10 10 10 45 200 10 10 11 45 300 10 10 13 45 400 10 10 14 45 500 10 10 15 45 600 10 10 16 45 700 10 10 17 45 800 10 10 17 45 1000 10 10 18 45 1250 12 12 19 45 1500 12 12 19 45 1750 12 12 19 45 2000 13 13 20 45 2500 14 14 21 45 3000 16 16 21 45 3500 16 16 22 45 4000 17 17 22 46 4500 17 17 23 47 5000 20 20 23 49 6000 20 20 24 50 7000 22 22 24 50 8000 22 22 25 53 10000 24 24 26 53 12500 24 24 26 55 15000 25 25 27 55 17500 25 25 27 57 20000 26 26 28 58 25000 27 27 29 60 30000 28 28 29 60 35000 30 30 30 61 40000 30 30 30 61 ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 323 45000 30 30 30 64 50000 30 30 30 64 60000 30 30 30 66 70000 30 30 30 66 80000 30 30 30 66 90000 30 30 30 67 100000 30 30 30 67 112500 30 30 30 69 125000 30 30 30 69 136000 30 30 30 70 150000 30 30 30 70 175000 30 30 30 71 200000 30 30 30 71 Table - 4 Safety distances (in metres) to be observed in a factory for manufacture of sparklers only From Capacity in Man To To To To To To Raw To kilogrammes Limit Mixing Dipping Drying Packing Transit material Dwelling of the shed shed shed plat- shed shed or empty house, form frames protected shed works Mixing shed 50 2 6 6 9 9 9 15 15 Dipping shed 200 8 6 6 3 9 9 15 15 Drying Platform 200 8 9 3 3 9 9 15 15 Packing shed 200 4 9 9 9 9 9 15 15 Transit shed 200 2 9 9 9 9 9 15 15 Raw material/ empty frames shed - 15 15 15 15 15 - - Table - 5 Safety distance (in metres) to be observed in a magazine for storage of sparklers only. From the magazine of storage To and between the magazine, To railway, To dwelling house, capacity in kilogrammes own sparklers manufacturing public road protected works shed or magazine office 50 to 35000 15 15 30 35001 to 70,000 15 15 35 70,001 to 200000 15 15 40 1 2 3 4 5 324 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] Ta bl e- 6 Sa fe ty d is ta nc e (i n m et re s) t o be o bs er ve d by v ar io us p ro ce ss a nd st or ag e sh ed s o f f ir ew or ks m an uf ac tu ri ng fa ct or y Fr om E xp lo si ve s M an T o T o T o T o T o fu se T o tr an si t sh ed T ra ns it sh ed ( qu ic k T o tr an si t T o T o dw el lin g L im it of th e Li m it m ix in g/ di pp in g dr yi ng m a n u- w ra pp in g (f ir ew or ks ) o f m at ch /m ic ro c or d/ sh ed ( pe lle t) ra w ho us e, sh ed i n fil lin g sh ed pl at fo rm fa ct ur in g sh ed ca pa ci ty in fu se ) of c ap ac ity of c ap ac ity i n m at er ia l pr ot ec te d ki llo gr a- sh ed sh ed ki llo gr am m es in k ill og ra m m es ki llo gr am m es sh ed w or ks o r m m es 30 0 40 0 50 0 10 0 15 0 20 0 ou t si de sa fe ty di st an ce s M ix in g/ fi lli ng 5 2 18 18 18 18 18 30 34 37 21 24 26 18 45 45 sh ed D ip pi ng s he d 5 2 18 12 18 12 12 30 34 37 21 24 26 18 45 45 D ry in g p la tf or m 25 4 18 12 12 12 12 30 34 37 21 24 26 18 45 45 M an uf ac tu ri ng 25 4 18 12 12 12 12 30 34 37 21 24 26 18 45 45 sh ed Fu se w ra pp in g 10 2 18 12 12 12 12 30 34 37 21 24 26 18 45 45 sh ed T ra ns it s he d 30 0 2 30 30 30 30 30 30 34 37 30 30 30 30 45 45 (f ir ew or ks ) 40 0 2 34 34 34 34 34 34 34 37 34 34 34 34 45 45 50 0 2 37 37 37 37 37 37 37 37 37 37 37 37 45 45 T ra ns it s he d 10 0 2 21 21 21 21 21 21 34 37 21 24 26 21 45 45 (q ui ck m at ch / 15 0 2 24 24 24 24 24 24 34 37 24 26 28 24 45 45 m ic ro c or d /f us e) 20 0 2 26 26 26 26 26 34 34 34 26 28 30 26 45 45 T ra ns it s he d 50 2 18 18 18 18 18 18 18 18 37 18 18 18 45 45 (p el le t) R aw m at er ia l X 45 45 45 45 45 45 45 45 45 45 45 45 X X sh ed N ot e: -— T he T ra ns it bu ild in g fo r s em i- fi ni sh ed fi re w or ks w ill h av e tw o co m pa rt m en ts e ac h of s iz e 2. 5 m et re s x 2. 0 m et re s - o ne e ac h fo r t he s to ra ge o f n on -e xp lo da bl e ite m s lik e w he el , f lo w er po ts e tc . a nd a no th er fo r s to ra ge o f e xp lo da bl e ite m s lik e cr ac ke rs , a to m b om bs e tc . ¹Hkkx II¹[k.M 3(i)º Hkkjr dk jkti=k % vlk/kj.k 325 Table-7 Safety distance (in metres) to be observed in transit building for storage of micro fuse and/or quick match Capacity in kilogrammes Safety distance from process Safety distance form protected and drying platform works or fencing 100 kilogrammes 21 45 150 kilogrammes 24 45 200 kilogrammes 26 45 [ F. No. 2(5)/2003-Expl] SANJAY. K. THADE, Director Printed by the Manager, Govt. of India Press, Ring Road, Mayapuri, New Delhi-110064 and Published by the Controller of Publications, Delhi-110054. —

Previous and next

All provisions of The Explosives Rules, 2008

Questions people ask

Is form DE - 2 of the Explosives Rules, 2008 still in force?

No repeal of the Explosives Rules, 2008 is recorded.