LawGrids logoLAWGRIDS.ORG

Rule 88, Atomic Energy (Factories) Rules, 1996: DANGEROUS MANUFACTURING PROCESSES OR OPERATIONS

Atomic Energy (Factories) Rules, 1996 - Rule 88

Text of rule 88

DANGEROUS MANUFACTURING PROCESSES OR OPERATIONS

88. DANGEROUS MANUFACTURING PROCESSES OR OPERATIONS.- (1) The following manufacturing processes or operations when carried on in any factory are declared to be dangerous manufacturing processes or operations, namely:- I. Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold, etc. II. Chemicals & Chemical works. III. Manipulation of stone or any other materials containing free silica IV. Grinding or glazing of metals V. Handling or manipulation of corrosive substances. VI. Foundry. VII. Electrical work. VIII. Beryllium operations IX. Zirconium operations. X. Cleaning or smoothing of articles by a jet of sand, metal shot or grit or other abrasive propelled by a blast of compressed air or steam. XI. Operations involving high noise level. XII. Highly flammable liquids & flammable compressed gases. XIII. Radioactive substances. XIV. Laser & Optical Radiations. XV. Motor Vehicle Garages. XVI. Cryogenic Liquids. XVII. Alkali Metals. (2) 'First Employment' means employment for the first time in a hazardous process or operation so notified under section 87,or Atomic Energy Factory Rules, 1996 122 Rules 88-88(Sch.I) re-employment therein after cessation of employment in such process or operation for a period exceeding three calendar months. (3) The provisions specified in the schedules to this rule shall apply to any class or description of factories wherein dangerous manufacturing processes or operations specified in each schedule are carried on. (4) The occupier of the factory will pay the required fees for the medical examinations of workers to be carried out by the Certifying Surgeon as required by the schedule annexed to this rule. (5) Notwithstanding the provisions specified in schedules to this rule, the Inspector may by issue of orders in writing to the manager or occupier or both, direct them to carry out such measures, and within such time as may be specified in such order with a view to removing conditions dangerous to the health of workers or to suspend any process where such process constitutes, in the opinion of the inspector imminent danger of poisoning or toxicity. (6) Any register or record of medical examinations and tests connected therewith required to be carried out under any of the schedules to this rule in respect of any worker shall be kept readily available to the Competent Authority and shall be preserved till the expiry of one year after the worker ceases to be in employment of the factory. SCHEDULE I ELECTROPLATING Electrolytic plating or oxidation of metal articles by use of an electrolyte containing acids, bases or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. 1. Definitions.- For the purposes of this Schedule - (a) "electrolytic process" means the electrolytic plating or oxidation of metal articles by the use of an electrolyte containing acids, bases , or salts of metals such as chromium, nickel, cadmium, zinc, copper, silver, gold etc. (b) "bath" means any vessel used for an electrolytic process or for any subsequent process; and (c) "employed" means employed in any process involving contact with liquid from a bath. Atomic Energy Factory Rules, 1996 123 Rule 88 (Sch.I) 2. Exhaust draught.- An efficient exhaust draught shall be applied to every vessel in which an electrolytic process is carried on. Such draught shall be provided by mechanical means and shall operate on the vapour or spray given off in the process as near as may be at the point of origin. The exhaust draught appliance shall be so constructed, arranged and maintained as to prevent the vapour or spray entering into any room or place in which work is carried on. 3. Prohibition relating to women.- No women, shall be employed or permitted to work at a bath. 4. Floor of workrooms.- The floor of every workroom containing a bath shall be impervious to water. The floor shall be maintained in good and level condition and shall be washed down at least once a day. 5. Protective devices.- (a) The occupier shall provide and maintain in good and clean condition the following articles of protective devices for the use of all persons employed on any process at which they are liable to come in contact with liquid from a bath and such devices shall be worn by the persons concerned - (i) waterproof aprons and bibs; and (ii) for persons actually working at a bath, loose-fitting rubber gloves and rubber boots or other waterproof footwear & chemical goggles. (b) The occupier shall provide and maintain for the use of all persons employed suitable accommodation for the storage and adequate arrangements for the drying of the protective devices. 6. Water facilities.- (a) There shall be provided & maintained in good repair for the use of all persons employed in electrolytic process & processes incidental to it - (i) a wash place under cover, with either (1) a trough with a smooth impervious surface filled with a waste pipe, & of sufficient length to allow at least 60 cm for every 5 persons employed at any one time, & having a constant supply of water from taps or jets above the trough at intervals of not more than 60cm.; or (2) at least one wash basin for every 5 such persons employed at any one time, fitted with a waste pipe & having a constant supply of water laid on. (ii) a sufficient supply of clean towels renewed daily, Atomic Energy Factory Rules, 1996 124 Rule 88(Sch.I) and soap or other suitable cleaning material. (b) In addition to the facility in sub-paragraph(a) an approved type of emergency shower with eye fountain shall be provided and maintained in good working order, where ever necessary, in order to ensure continuous water supply , storage tank of 1500 litres capacity shall be provided as a source of clean water for emergency use. 7. Cautionary placard.-A cautionary placard in the form specified below and printed in the language of the majority of the workers employed shall be affixed in a prominent place in the factory where it can be easily and conveniently read by the workers. CAUTIONARY NOTICE Electrolytic Plating 1. Chemicals handled in this plant are corrosive and poisonous. 2. Smoking, chewing tobacco, eating food or drinking, in this area is prohibited. No food stuff or drink shall be brought in this area. 3. Some of these chemicals may be absorbed through the skin and may cause poisoning. 4. A good wash shall be taken before meals. 5. Protective devices supplied shall be used while working in this area. 6. Spillage of the chemicals on any part of the body or on the floor shall be immediately washed away with water. 7. All workers shall undergo the prescribed medical tests regularly to protect their own health. 8. Medical facilities and records of examinations and tests.- (a) The occupier of every factory in which electrolytic processes are carried on shall - (i) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Competent Authority ; Atomic Energy Factory Rules, 1996 125 Rule 88(Sch.I) (ii) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (i); and (iii) maintain a sufficient supply of suitable barrier cream, ointment & impermeable water proof plaster in a separate box readily accessible to the workers and used solely for the purpose of keeping these substances. In case cyanides are used in the bath, the box shall also contain an emergency cyanide kit. (b) The medical practitioner shall examine all workers before they are employed in electrolytic processes. Such examination in case of chrome plating shall include inspection of hands, forearms and nose and will be carried out once at least in every fortnight. (c) The record of the examinations referred to in sub- paragraph (b) shall be maintained in a separate register in Form 1A which shall be kept readily available for inspection by the inspector. 9. Medical examination by the Certifying Surgeon.- (a) Every worker employed in the electrolytic processes shall be examined by a Certifying Surgeon before his first employment. Such examination shall include X-ray of the chest and- (i) in case of chromium plating include examination for nasal septum perforation and test for chromium in urine; (ii) in case of nickel plating, test for nickel in urine; and (iii) in case of cadmium plating, test for cadmium in urine & alpha - 2 microglobulin in urine. (b) No worker shall be employed in any electrolytic process unless certified fit for such employment by the Certifying Surgeon. (c) Every worker employed in the electrolytic processes shall be re-examined by a Certifying Surgeon at least once in every year, except in case of the workers employed in cadmium, chromium & nickel plating processes for whom this examination shall be carried out once in every 6 months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified under sub- paragraph (a) excluding the X-ray of the chest which shall not be required normally to be carried out earlier than once in three years. Atomic Energy Factory Rules, 1996 126 Rule 88(Sch.I-II) (d) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 1. The record of examination and re-examinations carried out shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (a) and (b), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 1A. (e) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. (f) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the electrolytic processes on the ground that continuance therein would involve danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents shall also include the period for which he considers that the said person is unfit for work in the said processes. The person declared unfit in such circumstances shall be provided with alternate placement facility unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (g) No person who has been found unfit to work as said in sub-paragraph (f) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit. SCHEDULE II CHEMICALS AND CHEMICAL WORKS PART I 1. Application.- This schedule shall apply to all manufactures and processes incidental thereto carried on in chemical works. 2. Definitions.- For the purposes of this schedule - (a) "chemical works " means any factory or such parts of any factory as are listed in appendix 'A' to this schedule; (b) "efficient exhaust draught" means localised ventilation effected by mechanical or other means for the removal of gas, vapour, fume or dust to prevent it from escaping into the environment of any place in which work is carried on; Atomic Energy Factory Rules, 1996 127 Rule 88(Sch.II) (c) "bleaching powder" means the bleaching powder commonly called chloride of lime; (d) "chlorate" means chlorate or perchlorate; (e) "caustic" means hydroxide of potassium or sodium; (f) "chrome process" means the manufacture of chromate or bichromate of potassium or sodium, or the manipulation, movement or other treatment of these substances; (g) "nitro or amino process" means the manufacture of nitro or amino derivatives of phenol and of benzene or its homologues, and the making of explosives with the use of any of these substances. (h) the term " permit to work" system means the compliance with the procedures laid down under para 20 of part II: (i) "toxic substances" means all those substances which when they enter into the human body, through inhalation or ingestion or absorption through skin, in sufficient quantities cause fatality or exert serious affliction of health, or chronic harmful effects on the health of persons exposed to it due to its inherent chemical or biological effects. In respect of substances whose permissible level of exposure abbreviated as PLE, as specified in the Second Schedule of section 41 F, exceeds the concentration specified therein would make the substances toxic; (j) "emergency" means a situation or condition leading to a circumstance or set of circumstances in which there is danger to the life or health of persons or which could result in big fire or explosion or pollution to the work and outside environment, affecting the workers or neighbourhood in a serious manner, demanding immediate action; (k) "dangerous chemical reactions" means high speed reactions, run-away reactions, delayed reactions, etc. and are characterised by evolution of large quantities of heat, intense release of toxic or flammable gases or vapours, sudden pressure build-up etc.; (l) "manipulation" means mixing, blending, filling, emptying, grinding, sieving, drying, packing, sweeping, handling, using, etc.; (m) "approved personal protective equipment" means items of personal protective equipment conforming to the relevant BIS specifications or in the absence of it, personal protective equipment approved by the Competent Authority; Atomic Energy Factory Rules, 1996 128 Rule 88(Sch.II) (n) "appropriate personal protective equipment" means that when the protective equipment is used by the worker, he shall have no risk to his life or health or body; and (o) "confined space" means any space by reason of its construction as well as in relation to the nature of the work carried therein and where hazards to the persons entering into or working inside exist or are likely to develop during working. PART II General Requirements Applying to all the works in Appendix 'A' of this Schedule 1. Housekeeping.- (a) Any spillage of materials shall be cleaned up before further processing. (b) Floors, platforms, stairways, passages & gangways shall be kept free of any obstructions. (c) There shall be provided easy means of access to all parts of the plant to facilitate cleaning. 2. Improper use of chemicals.- No chemicals or solvents or empty containers of chemicals or solvents shall be permitted to be used by workers for any purposes other than the for which they are supplied. 3. Prohibition on the use of food, etc.- No food, drink, tobacco, pan or any edible item shall be stored or heated or consumed on or near any part of the plant or equipment. 4. Cautionary Notices and Instructions.- (a) Cautionary notices in a language understood by the majority of workers shall be prominently displayed in all hazardous areas drawing the attention of all workers about the hazards to health, hazards involving fire and explosion and any other hazard such as consequences of testing of material or substances used in the process or using any contaminated container for drinking or eating, to which the workers' attention shall be drawn for ensuring their safety & health. (b) In addition to the above customary notice, arrangement shall be made to instruct and educate all the workers including illiterate workers about the hazards in the process including the specific hazards to which they may be exposed to, in the normal course of their work. Such instructions and education shall also deal with the hazards involved in unauthorised and unsafe practices including the properties of substances used in the process under normal conditions as well as abnormal conditions and the precautions to be observed against Atomic Energy Factory Rules, 1996 129 Rule 88(Sch.II) each and every hazard. Further, an undertaking from the workers shall be obtained within 1 month of their employment and for old workers employed, within one month of coming into operation of the rules, to the effect that they have read the contents of the cautionary notices and instructions, understood them and would abide by them. The training and instructions to all workers and all supervisory personnel shall include the significance of different types of symbols and colours used on the labels stuck or painted on the various types of containers and pipe lines. 5. Evaluation and provision of safeguards before the commencement of process.- (a) Before commencing any process or any experimental work, or any new manufacture covered under Appendix 'A', the occupier shall take all possible steps to ascertain definitely all the hazards involved both from the actual operations and the chemical reactions including the dangerous chemical reactions. The properties of the raw materials used, the final products to be made, and any by-products derived during manufacture, shall be carefully studied and provisions shall be made for dealing with any hazards including effects on workers, which may occur during manufacture. (b) Information in writing giving details of the process, its hazards and the steps taken or proposed to be taken from the design stage to the disposal stage for ensuring the safety as in sub-para (a) above shall be sent to the Competent Authority at the earliest but in no case less than 15 days before commencing manufacture, handling, or storage of any of the items covered under appendix A, whether on experimental basis, or as pilot plant or as trial production, or as large scale manufacture. (c) The design, construction, installation, operation, maintenance and disposal of the buildings, plant and facilities shall take into consideration effective safeguards against all the safety and health hazards so evaluated. (d) The requirements under the sub-para (a) to (c) shall not act in lieu of or in derogation to, any other provisions contained in any Act governing the work. 6. Authorised entry.- Authorised persons only shall be permitted to enter any section of the factory or plant on or where dangerous chemical reactions are taking place or where hazardous chemical reactions are taking place or where hazardous chemicals are stored. 7. Examination of instruments and safety devices.- (a) All instruments and safety devices used in the process shall be tested before taking into use and after carrying out any repair to them and examined once in a month, by a competent person. Atomic Energy Factory Rules, 1996 130 Rule 88(Sch.II) Records of such tests and examinations shall be maintained in a register. (b) All instruments and safety devices used in the process shall be operated daily or as often as it is necessary, to ensure its effective and efficient working at all times. 8. Electrical installations.- All electrical installations used in the process covered in Appendix 'A' shall be of an appropriate type to ensure safety against the hazard prevalent in that area such as suitability against dust, dampness, corrosion, flammability and explosivity etc. and shall conform to the relevant BIS specifications governing their construction and use for that area. 9. Handling and storage of chemicals.- (a) The containers for handling and storage of chemicals shall be of adequate strength taking into consideration the hazardous nature of the contents. They shall also be provided with adequate labeling and colour coding arrangements to enable identification of the containers and their contents indicating the hazards and safe handling methods and shall conform to the respective BIS standards. The instructions given in the label shall be strictly adhered to. Damaged containers shall be handled only under supervision of a knowledgeable and responsible person and spillage shall be rendered innocuous in a safe manner using appropriate means. (b) The arrangements for the storage of chemicals including charging of chemicals in reaction vessels and containers shall be such as to prevent any risk of fire or explosion or formation of toxic concentration of substances above the limits specified in Second Schedule of Section 41F. (c) Without prejudice to the generality of the requirements in sub-para (b) above, the arrangements shall have suitable ventilation facilities and shall enable the maintenance of safe levels in vessels and containers. Such arrangements shall also take into consideration, the type of flooring , capacity of flooring and the compatibility requirements of substances with other chemicals stored nearby. (d) (i) Storage of chemicals and intermediate products, which are highly unstable or reactive or explosive shall be limited to the quantities required for two months use. (ii) Whenever the quantities laid down in the above clause (a) are to be exceeded, the permission of the Competent Authority shall be obtained. (iii) Notwithstanding anything contained in clause(i)& (ii) above, the Competent Authority may direct any factory Atomic Energy Factory Rules, 1996 131 Rule 88(Sch.II) carrying out processes covered in Appendix 'A' to further limit the storage of hazardous substances to quantities less than two months on considerations of safety. (e) Standby arrangements equal to the biggest container shall always be available to transfer the toxic substances quickly into the standby storage facility if any defect develops in any of the container resulting in the release of toxic substances. (f) Any storage facility constructed using nonmetallic material such as Fibreglass Reinforced Plastics (FRP), all glass vessels etc., shall have adequate strength to withstand the stress, if any exerted by the contents and shall be properly anchored. Working platforms, access ladders, pipelines etc. used in such storage facility shall not have any support on the structure of the storage facility and shall be independently supported. 10. Facility for isolation.- The plant and equipment shall be so constructed and maintained as to enable quick isolation of plant or part of plant or equipment, with appropriate indication. One copy of the layout plan indicating the isolation facilities shall always be available with the security personnel, the maintenance and the health and safety personnel and these isolation facilities shall be checked for its effectiveness once in a month. 11. Personal protective equipment.- (a) All workers exposed to the hazards in the processes covered by this Schedule shall be provided with appropriate and approved type of personal protective equipment. Such equipment shall be in a clean, sterile and hygienic condition before issue. (b) The occupier shall arrange to inform, educate and supervise all the workers in the use of personal protective equipment while carrying out the job. (c) As regards any doubt regarding the appropriateness of any personal protective equipment, the decision of the Competent Authority shall be final. 12. Alarm Systems.- (a) Suitable and effective alarm systems giving audio-visual indications, shall be installed at the control room as well as in all strategic locations where process control arrangements are available so as to enable corrective action to be taken before the operational parameters exceed the predetermined safe levels or lead to conditions conducive for an outbreak of fire or explosion to occur. Such alarm systems shall be checked daily and tested at least once in a month to ensure its performance efficiency at all times. Atomic Energy Factory Rules, 1996 132 Rule 88(Sch.II) (b) The Competent Authority may direct such system to be installed in case of plants or processes where toxic materials are being used and spillage or leakage of which may cause wide spread poisoning in or around the plant. 13. Control or escape of substances into the work atmosphere.- (a) Effective arrangements such as, enclosure, or by pass, or efficient exhaust draught, maintenance of negative pressure etc., shall be provided in all plants, containers, vessels, sewers, drains, flues, ducts, culverts, and buried pipes and equipment, to control the escape and spread of substances such are likely to give rise to fire or explosion or toxic hazards during normal working and in the event of accident or emergency. (b) In the event of the failure of the arrangements for control resulting in the escape of substances in the work atmosphere immediate steps shall be taken to control the process in such a manner, that further escape is brought down to the safe level. (c) The substances that would have escaped into the work atmosphere before taking immediate steps as required in sub-para (b), shall be rendered innocuous by diluting with air or water or any other suitable agent or by suitably treating the substances. 14. Control of dangerous chemical reactions.- Suitable provision, such as automatic and or remote control arrangements shall be made for controlling the effects of 'dangerous chemical reactions'. In the event of failure of control arrangements, automatic flooding or blanketing or other effective arrangements shall come into operation. 15. Testing, examination and repair of plant & equipment.- (a) All parts of plant, equipment and machinery used in the process which in the likely event of their failure may give rise to an emergent situation shall be tested by a competent person before commencing process and retested at an interval of two years or after carrying out repairs to it. The competent person shall identify the parts of the plant, equipment and machinery required to be tested as aforesaid and evolve suitable testing procedures. In carrying out the test as mentioned above in respect of pressure vessels or reaction vessels the following precautions shall be observed, namely:- (i) before the test is carried out, each vessel shall be thoroughly cleaned and examined externally and as far as practicable, internally also for surface defects, corrosion and foreign matter . During the process of cleaning and removal of sludge, if any, all due precautions shall be taken against fire or explosion, if such sludge is of pyrophoric nature or contains spontaneously combustible chemicals; Atomic Energy Factory Rules, 1996 133 Rule 88(Sch.II) (ii) as soon as the test is completed, the vessel shall be thoroughly dried internally and shall be clearly stamped with the marks and figures indicating the person by whom testing has been done and the date of test; and (iii) any vessel which fails to pass the test or which for any other reason is found to be unsafe for use shall be destroyed or rendered unusable under intimation to the Competent Authority. (b) All parts of plant, equipment, machinery which in the likely event of failure may give rise to an emergent situation shall be examined once in a month by the competent person. (c) Records of testing and examination referred to in paragraphs (a) and (b) shall be maintained as long as that part of the plant, equipment and machinery are in use. (d) All repair work including alteration, modification and addition to be carried out to the plant, equipment and machinery shall be done under the supervision of a responsible person who shall evolve a procedure to ensure safety and health of persons doing the work. When repairs or modification is done on pipelines, and joints are required to be welded, butt welding of joints shall be preferred. Wherever necessary, the responsible person shall regulate the aforesaid work through a 'Permit to work system'. 16. Staging.- (a) All staging that is erected for the purpose of maintenance work or repair work or for work connected with entry into confined spaces and used in the processes included in Appendix 'A', shall be stable, rigid and constructed out of substantial material of adequate strength. Such staging shall conform to the respective Indian Standards & Specifications. (b) Staging shall not be erected over any closed or open vessel unless the vessel is so constructed and ventilated to prevent exposure of persons working on the stages. (c) All the staging constructed for the purpose of this para shall give appropriate access which are safe and shall be fitted with proper hand rails to a height of one metre and toe board. 17. Seating Arrangements.-The seating arrangements provided for the operating personnel working in processes covered in Appendix 'A' shall be located in a safe manner as to prevent the exposure to toxic, flammable and explosive substances evolved in the work environment in the course of manufacture or repair or maintenance, either due to failure of plant and equipment or due to the substances which are under pressure, escaping into the Atomic Energy Factory Rules, 1996 134 Rule 88(Sch.II) atmosphere. 18. Entry into or work in confined spaces.- (a) The occupier of every factory to which the provisions of this schedule apply, shall ensure the observance of the following precautions before permitting any person to enter or work inside the confined spaces- (i) identify all confined spaces and the nature of hazards that are encountered in such spaces, normally or abnormally, and arrange to develop the most appropriate safeguards for ensuring the safety and health of persons entering into or working inside, the confined spaces; (ii) regulate the entry or work inside the confined spaces through a 'permit to work system' which should include the safeguards so developed as required under sub-clause (i) above; (iii) before testing the confined space for entry into or work, the place shall be rendered safe by washing or cleaning with neutralizing agents; or purging with steam or inert gases and making adequate forced ventilation arrangements or such measure which will render the confined space safe; (iv) shall arrange to carry out such tests as are necessary for the purpose by a competent person and ensure that the confined space is safe for the persons to enter or work. Such testing shall be carried out as often as is necessary during the course of work to ensure its continued safety; (v) shall arrange to educate and train the personnel who would be required to work in confined spaces about the hazards involved in the work. He shall also keep in readiness the appropriate and approved personal protective equipment including arrangements for rescue, resurrection and first aid, and shall arrange supervision of the work at all times by a responsible and knowledgeable person. (b) The manager shall maintain a log of all entry into or work in, confined spaces and such record shall contain the details of persons assigned for the work, the location of the work and such other details that would have a bearing on the safety and health of the persons assigned for this work. The log book so maintained shall be retained as long as the concerned workers are in service and produced to the inspector when demanded. 19. Maintenance work etc.- (a) All the work connected with the maintenance of plants and equipment including cleaning of empty Atomic Energy Factory Rules, 1996 135 Rule 88(Sch.II) containers which have held hazardous substances used in the processes covered in this Schedule, shall be carried out under 'permit to work system' employing trained personnel and under the supervision of responsible person, having knowledge of the hazards and precautions required to deal with them. (b) Maintenance work shall be carried out in such a manner that there is no risk to persons in the vicinity or to persons who pass by. If necessary, the place of such work shall be cordoned off or the presence of unconnected persons effectively controlled. 20. Permit to work system.- The permit to work system shall inter-alia include the observance of the following precautions while carrying out any specified work to be subjected to the permit to work system - (a) all work subject to the permit to work system shall be carried out under the supervision of a knowledgeable and responsible person; (b) all parts of plant or machinery or equipment on which permit to work system is carried out shall remain isolated from other parts throughout the period of permit to work and the place of work including the parts of plant, machinery shall be rendered safe by cleaning, purging, washing, etc.; (c) all work subject to the permit to work system shall have pre-determined work procedures which integrate safety with the work. Such procedures shall be reviewed whenever any change occurs in material or equipment so that continued safety is ensured; (d) persons who are assigned to carry out the permit to work system shall be physically fit in all respects taking into consideration the demands and nature of the work before entering into the confined space. Such person shall be adequately informed about the correct work procedures as well as the precautions to be observed while carrying out the permit to work system; (e) adequate rescue arrangements wherever considered necessary and adequate first aid, rescue and resurrection arrangements shall be available in good working condition near the place of work while carrying out the permit to work system., for use in emergency; (f) appropriate and approved personal protective equipment shall be used while carrying out the 'permit to work system'; Atomic Energy Factory Rules, 1996 136 Rule 88(Sch.II) (g) after completion of work subject to the 'permit to work system' the person responsible shall remove all the equipment and tools and restore to the original condition so as to prevent any danger while carrying out regular process. 21. Safety sampling personnel.- The occupier shall ensure the safety of persons assigned for collecting samples by instructing them on the safe procedures. Such personnel shall be provided with proper and approved personal protective equipment, if required. 22. Ventilation.- Adequate ventilation arrangements shall be provided and maintained at all times in the process area where dangerous or toxic or flammable or explosive substances could be evolved. These arrangements shall ensure that concentrations, which are either harmful or could result in explosion, are not permitted to be built up in the work environment. 23. Procedures for meeting emergencies.- (a) The occupier of every factory carrying out the works covered in Appendix 'A', shall arrange to identify all types of possible emergencies that could occur in the processes during the course of work or while carrying out maintenance work or repair work. The emergencies so identified shall be reviewed every year. (b) The occupier shall formulate a detailed plan to meet all such identified emergencies including arrangements for summoning outside help for rescue and fire fighting and arrangements for making available urgent medical facilities. (c) The occupier shall send the list of emergencies and the details of procedures and plans formulated to meet the emergencies, to the Competent Authority. (d) The occupier shall arrange to install distinctive and recognizable warning arrangements to caution all persons inside the plant as well as the neighbouring community, if necessary, to enable evacuation of persons and to enable the observance of emergency procedures by the persons who are assigned emergency duties. All concerned must be well informed about the warning arrangements and their meaning. The arrangements must be checked for its effectiveness every month. (e) Alternate power supply arrangements shall be made and interlocked with the normal power supply system so as to ensure constant supply of power to the facilities and equipment meant for compliance with requirements of Paragraphs 10, 11, 12, 13, 14, 18, 22, and this paragraph of Part II, Part III, Part IV and Part V of this Schedule. Atomic Energy Factory Rules, 1996 137 Rule 88(Sch.II) (f) The occupier shall arrange to suspend the further process work in a place where emergency is established and shall forthwith evacuate all persons in the area except workers who have been assigned emergency duties. (g) All the employees of the factory shall be trained about the action to be taken by them including evacuation procedures during emergencies. (h) All emergency procedures must be rehearsed every three months and deficiencies, if any, in the achievement of the objectives shall suitably be corrected. (i) The occupier shall arrange to have ten percent of the workers trained in the use of First Aid Fire Fighting appliances and in the rendering of specific First Aid measures taking into consideration the special hazards of the particular process. (j) The occupier shall furnish immediately on request the specific chemical identity of the hazardous substance to the treating physician when the information is needed to administer proper emergency or first-aid treatment to exposed persons. 24. Danger due to effluents.- (a) Adequate precautions shall be taken to prevent the mixing of effluents from different processes and operations which may cause dangerous or poisonous gases to be evolved. (b) Effluents which contain or give rise in the presence of other effluents to poisonous gases shall be provided with independent drainage systems to ensure that they may be trapped and rendered safe. PART III Fire and Explosion Risks & Counter Measures 1. Sources of ignition including lighting installation.- (a) No internal combustion engine and no electric motor or other electrical equipment, and fittings and fixtures capable of generating sparks or otherwise causing combustion or any other source of ignition or any naked light shall be installed or permitted to be used in the process area where there could be fire and explosion hazards. (b) All hot exhaust pipes shall be installed outside a building and other hot pipes or hot surface or surfaces likely to become hot shall be suitably protected. (c) The classification of work areas in terms of its hazard potential and the selection of electrical equipment or other Atomic Energy Factory Rules, 1996 138 Rule 88(Sch.II) equipment that could constitute a source of ignition shall be in accordance with the respective Indian Standard. (d) Where a flammable atmosphere may be prevalent or could occur, the soles of footwear worn by workers shall have no metal on them, and the wheels of trucks or conveyors shall be conductive type. (e) All tools and appliances used for work in this area shall be of non-sparking type. (f) Smoking in process areas where there are risks of fire and explosion shall be prohibited, and warning notices in the language understood by majority of workers shall be posted in the factory prohibiting smoking in specified areas. 2. Static electricity.- (a) All machinery and plant, particularly, pipe lines and belt drives, on which static charge is likely to accumulate, shall be effectively earthed. Receptacles for flammable liquids shall have metallic connections to the earthed supply tanks to prevent static sparking. Where necessary, humidity shall be regulated. (b) Mobile tanker wagons shall be earthed during filling and discharge, and precautions shall be taken to ensure that earthing is effective before such filling or discharge takes place. 3. Lightning protection.- Lightning protection arrangement shall be fitted where necessary, and shall be maintained. 4. Process heating.- The method of providing heat for a process likely to result in fire and explosion shall be as safe as possible and where the use of naked flame is necessary, the plant shall be so constructed as to prevent any escaping flammable gas, vapour, or dust coming into contact with the flame, or exhaust gases, or other sources likely to cause ignition. Wherever possible, the heating arrangement shall be automatically controlled at a pre-determined temperature below the danger temperature. 5. Leakage of flammable liquids.- (a) Provision shall be made to confine by means of bund walls, dykes, sumps etc. possible leakages from storage vessels containing flammable liquids. (b) Waste material in contact with flammable substances shall be disposed off suitably under the supervision of knowledgeable and responsible person. (c) Adequate and suitable fire-fighting appliances shall be installed in the vicinity of such vessels. Atomic Energy Factory Rules, 1996 139 Rule 88(Sch.II) 6. Safety valves.- Every still and every closed vessel in which gas is evolved or into which gas is passed, and in which the pressure is liable to rise above the atmospheric pressure, shall have attached to it a pressure gauge, and a proper safety valve or other equally efficient means to relieve the pressure. These appliances shall be maintained in good condition. 7. Installation of pipe line etc.- All pipelines carrying flammable or explosive substances shall be protected from mechanical damage and shall be examined by a responsible person once in a week to detect any deterioration or defects, or accumulation of flammable or explosive substances, and record kept of any defects found and repairs made. 8. Fire fighting systems.- (a) Every factory employing 500 or more persons and carrying out processes listed in Appendix 'A' shall provide - (i) trained and responsible fire fighting squad so as to effectively handle the fire fighting and life saving equipment in the event of fire or other emergency. Number of persons in this squad will necessarily depend upon the size of risk involved, but in no case shall be less than 8 such trained persons to be available at any time. The squad shall consist of watch & ward personnel, fire pumpman and departmental supervisors and operators trained in the operation of fire & emergency services; (ii) squad leaders shall preferably be trained in a recognised government institution and their usefulness enhanced by providing residence on the premises; and (iii) squad personnel shall be provided with clothing and equipment including helmets, boots and belts. (b) A muster roll showing the duties allocated to each member of the squad shall be prepared and copies supplied to each leader as well as displayed in prominent places so as to be easily available for reference in case of emergency. (c) The pumpman shall be thoroughly conversant with the location of all appliances. He shall be responsible for maintaining all fire fighting equipment in proper working order. Any defect coming to his notice shall be immediately be brought to the notice of squad leader. (d) As far as is practicable, the fire pump room and the main gate(s) of the factory be connected to all manufacturing or storing areas through telephone interlinked and placed in a convenient location near such areas. Atomic Energy Factory Rules, 1996 140 Rule 88(Sch.II) PART IV Risks of Toxic Substances 1. Leakage.- (a) All plants shall be so designed and constructed as to prevent the escape of toxic substance. Where necessary, separate buildings, rooms, or protective process and the buildings shall be so designed as to localise any escape of toxic substances. (b) Catch pits, bund walls, dykes, or other suitable safeguards shall be provided to restrict the serious effects of such leakages. Catch pits shall be placed below joints in pipelines where there is danger involved to maintenance and other workers from such leakage. 2. Drainage.- Adequate drainage shall be provided and shall lead to collection tanks specifically provided for this purpose where in deleterious material shall be neutralised, treated or otherwise rendered safe before it is discharged into public drains or sewers. 3. Covering of vessels.- (a) Every fixed vessel or structure containing any toxic substance and not so covered as to eliminate all reasonable risk of accidental contact of any portion of the body of a worker, shall be so constructed as to avoid physical contact. (b) Such vessel shall, unless its edge is at least 90 cm above the adjoining ground or platform, be securely fenced to a height of at least 90 cm above such adjoining ground or platform. (c) Where such vessels adjoin and the space between them, clear of any surrounding brick or other work is either less than 45 cm in width or is 45 or more cm in width, but is not securely fenced on both sides to a height of at least 90 cm, secure barriers shall be so placed as to prevent passage between them: Provided that sub-paragraph (b) of this paragraph shall not apply to - (i) saturators used in the manufacture of sulphate of ammonia; and (ii) that part of the sides of brine evaporating pans which require raking, drawing or filling. 4. Continuous exhaust arrangement.- (a) Any process evolving toxic vapour, gas fume and substance shall have efficient continuous exhaust draught. Such arrangement shall be interlocked in the process control wherever possible. Atomic Energy Factory Rules, 1996 141 Rule 88(Sch.II) (b) In the event of failure of continuous exhaust arrangement means shall be provided to automatically stop the process. 5. Work bench.- All the work benches used in processes involving the manipulation of toxic substances, shall be graded properly and shall be made of smooth impervious surface which shall be washed daily after the completion of work. 6. Waste disposal.- (a) There shall be provided a suitable receptacle made of non-absorbable material with a tightly fitting cover for depositing waste material soiled with toxic substances and the contents of such receptacle shall be destroyed by burning or using other suitable methods under the supervision of a responsible person. (b) During the course of manufacture, whenever any batch or intermediate products having toxicity is rejected on considerations of quality, sufficient precautions shall be taken to render them innocuous or otherwise treat them or inactivate them, before disposal. (c) The empty containers of toxic substances shall be cleaned thoroughly before disposal under the supervision of a responsible person. PART V Special Precautions 1. Special precautions for Nitro or Amino Processes.- (a) Unless the crystallised nitro or amino substances or any of its liquor is broken or agitated in a completely enclosed process so as not to give rise to dust or fume, such process shall be carried on under an efficient exhaust draught or by adopting any other suitable means in such a manner as to prevent the escape of dust or fume in the working atmosphere. (b) No part of the plant or equipment or implements which was in contact with nitro or amino compounds shall be repaired, or handled unless they have been emptied and thoroughly cleaned and decontaminated. (c) Filling of containers with nitro or amino compounds shall be done only by using a suitable scoop to avoid physical contact and the drying of the containers in the stove shall be done in such a manner that the hot and contaminated air from the stove is not drawn into the work room. (d) Processes involving the steaming into or around any vessel containing nitro or amino compounds or its raw materials Atomic Energy Factory Rules, 1996 142 Rule 88(Sch.II) shall be carried out in such a manner that the steam or vapour is effectively prevented to be blown back into the working atmosphere. (e) Suitable antidotes such as methylene blue injections shall always be available at designated places of work for use during emergency involving the poisoning with nitro or amino compounds. 2. Special precautions for 'chrome processes'.- (a) Grinding and sieving of raw materials in chrome processes shall be carried on in such a manner and under such condition as to secure effective separation from any other processes and under an efficient exhaust draught. (b) There shall be washing facilities located very near to places where wet chrome processes such as leaching, acidification, sulphate settling, evaporation, crystallisation, centrifugation or packing are carried out, to enable quick washing of affected parts of body with running water. (c) Weekly inspection of hand and feet of all persons employed in chrome process shall be done by a qualified nurse and record of such inspections shall be maintained in form 1A. (d) There shall be always available at designated places of work suitable ointment such as glycerine, vaseline, etc. and water proof plaster in a separate box readily accessible to the workers so as to protect against perforation of nasal septum. 3. Special precautions for processes carried out in all glass vessels.- (a) Process and chemical reactions such as manufacture of vinyl chloride, benzyl chloride etc. which are required to be carried out in all glass vessels shall have suitable means like substantial wiremesh covering to protect persons working nearby in the event of breakage of glass vessel. (b) Any spillage or emission of vapour from the all glass vessel due to breakage, shall be immediately inactivated or rendered innocuous by suitable means such as dilution with water or suitable solvents so as to avoid the risks of fire or explosion or health hazards. 4. Special precautions for processes involving chlorate manufacture.- (a) Crystallisation, grinding or packing of chlorate shall not be done in a place used for any other purpose and such places shall have hard, smooth and impervious surface made of non-combustible material. The place shall be thoroughly cleaned daily. Atomic Energy Factory Rules, 1996 143 Rule 88(Sch.II) (b) The personnel protective equipment like overall, etc. provided for the chlorate workers shall not be taken from the place of work and they shall be thoroughly cleaned daily. (c) Adequate quantity of water shall be available near the place of chlorate process for use during fire emergency. (d) Wooden vessels shall not be used for the crystallisation of chlorate or to contain crystallised ground chlorate. 5. Special precautions in the use of plant and equipment made from reinforced plastics.- (a) All plant and equipments shall conform to appropriate Indian or any other National Standards. (b) Care shall be taken during storage, transport handling and installation of plant and equipments to avoid accidental damage. (c) All plant and equipments shall be installed in such a way as to ensure that loads are distributed as intended in design or as per the recommendations of the manufacturers. (d) All pipe work shall be supported so that total loads local to the branches on the vessel or tank do not exceed their design values. (e) After erection all plant and equipments shall be subjected to a pressure test followed by a thorough examination by a competent person. The test and examination shall be as per relevant Standard. A certificate of test and examination by competent person shall be obtained and kept available at site. (f) All plant and equipments shall be subjected to periodical test and examination and record maintained as per Paragraph 15 in Part II of this Schedule. (g) Plant and equipments during their use shall not be subjected to over filling or over loading beyond rated capacity. Atomic Energy Factory Rules, 1996 144 Rule 88(Sch.II) PART VI Medical Requirements 1. Decontamination facilities.- In all places where toxic substances are used in processes listed in Appendix 'A' the following provisions shall be made to meet an emergency, namely:- (a) Fully equipped first aid box; (b) Readily accessible means of drenching with water persons, parts of body of persons, and clothing of persons who have been contaminated with such toxic and corrosive substances, and such means shall be as shown in the Table below:- TABLE No. of persons employed at any time No. of drenching showers Up to 50 persons 2 between51 to 100 3 101 to 200 3+1 for every 50 persons thereafter 201 to 400 5+1 for every 100 " " 401 and above 7+1 for every 200 " " (c) A sufficient number of eye wash bottles filled with distilled water or suitable liquid, kept in boxes or cupboards conveniently situated and clearly indicated by a distinctive sign which shall be visible at all times. 2. Occupational health centre.-In all the factories carrying out processes covered in Appendix 'A' there shall be provided and maintained in good order an occupational health centre with facilities as per scale laid down hereunder - (a) For factories employing up to 50 workers- (i) the services of a qualified medical practitioner here-in - after known as Factory Medical Officer, shall be available for seeking medical help during emergency. He will also carry out the pre-employment and periodical medical examinations as stipulated in paragraph 4 of this part; (ii) a minimum of five persons trained in first aid procedures, amongst whom at least one shall always be available during the working period; and (iii) a fully equipped first aid box. Atomic Energy Factory Rules, 1996 145 Rule 88(Sch.II) (b) For factories employing 51 to 200 workers - (i) the occupational health centre shall have a room having a minimum floor area of 15 sq.m , with floors and walls made of smooth, hard and impervious surface and shall be adequately illuminated, ventilated and equipped; (ii) services of medical doctor shall be available in normal working hours as well as during emergency at centre; (iii) there shall be one qualified and trained dresser-cum- compounder on duty throughout the working period; and (iv) a fully equipped first aid box. (c) For factories employing above 200 workers- (i) there shall be one full-time Factory Medical Officer for factories employing up to 500 workers and one more medical officer for every 1000 workers or part thereof; (ii) the occupational health centre in this case shall have a minimum of 2 rooms each having a minimum floor area of 15 sq.m with floors and walls made of smooth, hard and impervious surface and shall be adequately illuminated, ventilated and equipped; (iii) there shall be one trained nurse, one dresser-cum- compounder and one sweeper-cum-ward boy throughout the working period; and (iv) the Occupational Health Centre in this case shall be suitably equipped to manage medical emergencies. 3. Ambulance van.- (a) In every factory carrying out processes covered in Appendix 'A', there shall be provided and maintained in good condition, a suitably constructed and fully equipped ambulance van as per Appendix 'C' manned by a full-time driver- cum- mechanic and a helper, trained in first aid for the purposes of transportation of serious cases of accidents or sickness unless arrangements for procuring such facility at short notice during emergencies have been made with the nearby hospital or other places. The ambulance van shall not be used for any purpose other than the purpose stipulated herein and will always be available near the Occupational Health Centre. (b) The relaxation to procure Ambulance Van from nearby places provided for in sub- para (1) above will not be applicable to factories employing more than 500 workers. Atomic Energy Factory Rules, 1996 146 Rule 88(Sch.II) 4. Medical examination.- (a) Workers employed in processes covered in Appendix 'A' shall be medically examined by a Factory Medical Officer in the following manner - (i) once before employment, to ascertain physical suitability of the person to do the particular job; (ii) once in a period of 6 months, to ascertain the health status of the worker; and (iii) the details of pre-employment and periodical medical examinations carried out as aforesaid shall be recorded in the prescribed form 1. (b) Any finding of the Factory Medical Officer revealing any abnormality or unsuitability of any person employed in the process shall immediately be reported to the Certifying Surgeon who shall in turn, examine the concerned workers and communicate his findings within 30 days. If the Certifying Surgeon is of the opinion that the person so examined is required to be suspended from the process for health protection he will direct the occupier accordingly, who shall not employ the said worker in the same process. However, the person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapaciated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated: Provided that the Certifying Surgeon on his own may examine any other worker whom he feels necessary to be examined for ascertaining the suitability of his employment in the process covered in Appendix 'A' or for ascertaining the health status of any other worker and his opinion shall be final. (c) No person shall be newly appointed without the Certificate of Fitness granted by the Factory Medical Officer. If the Factory Medical Officer declares a person unfit for being appointed to work in the process covered in Appendix 'A', such person shall have a right of appeal to the Certifying Surgeon, whose opinion shall be final in this regard. (d) The worker suspended from the process owing to the circumstances covered in sub-para (b) shall be employed again in the same process only after obtaining the Fitness Certificate from the Certifying Surgeon and after making entries to that effect in the health register. Atomic Energy Factory Rules, 1996 147 Rule 88(Sch.II) PART VII Additional Welfare Amenities 1. Washing facilities.- (a) There shall be provided and maintained in every factory for the use of all the workers taps for washing, at the rate of one tap for every 115 persons including liquid soap in a container with tilting arrangements and nail brushes or other suitable means for effective cleaning, such facilities shall be conveniently accessible and shall be kept in a clean and hygienic condition. (b) If washing facilities as required above are provided for women, such facilities shall be separate for them and adequate privacy at all times shall be ensured in such facilities. 2. Mess room facilities.- (a) The occupier of all the factories carrying out process covered in Appendix 'A' and employing 50 workers or more, shall provide for all the workers working in a shift mess room facilities which are well ventilated and provided with tables and sitting facilities along with the provision of cold and hygienic drinking water facilities. (b) Such facilities shall include suitable arrangements for cleaning and washing and shall be maintained in a clean and hygienic condition. 3. Cloakroom facilities.- (a) The occupier of every factory carrying out any process covered in Appendix 'A' shall provide for all the workers employed in the process cloak room facilities with lockers. Each worker shall be provided with two lockers, one for work clothing and another separately for personal clothing and the lockers should be such as to enable the keeping of the clothing in a hanging position. (b) The cloak room facilities so provided in pursuance of sub-para (a) shall be located as far as possible near to the facilities provided for washing in pursuance of para 1(a). If it is not possible to locate the washing facilities the cloak room facilities shall have adequate and suitable arrangements for cleaning & washing. 4. Special bathing facilities.- (a) The occupier of any factory carrying out the process covered under Appendix 'B' shall provide special bathing facilities for all the workers employed and such facilities shall be provided at the rate of 1 for 25 workers and part thereof, and shall be maintained in a clean and hygienic condition. Atomic Energy Factory Rules, 1996 148 Rule 88(Sch.II) (b) The occupier shall insist all the workers employed in the processes covered in Appendix 'B' to take bath after the completion of the day's or shift work using the bathing facilities so provided and shall also effectively prevent such of those workers taking bath in any place other than the bathing facilities. (c) Notwithstanding anything contained in sub-para (a) above, the Competent Authority may require in writing the occupier of any factory carrying out any other process for which in his opinion bathing facilities are essential from the health point of view, to provide special bathing facilities. PART VIII Duties of Workers 1. Duties of workers.- (a) Every worker employed in the processes covered in Appendix 'A' and appendix 'B' shall not make safety device or appliance or any guarding or fencing arrangement, inoperative or defective and shall report the defective condition of the aforesaid arrangements as soon as he is aware of any such defect. (b) Before commencing any work, all workers employed in processes covered in Appendix 'A' shall check their workplace as well as the machinery, equipment or appliance used in the processes and report any mal-function or defect immediately to the supervisor or any responsible person of the management. (c) All workers shall co-operate in all respects with the management while carrying out any work or any emergency duty assigned to them in pursuance of this schedule and shall always use all the personal protective equipments issued to them in a careful manner. (d) All workers employed in the processes covered in Appendix 'A' or Appendix 'B' shall not smoke in the process area or storage area. If special facilities are provided by the management only such facilities shall be used. (e) All workers employed in the processes covered in Appendix 'A' shall not remain in unauthorised place or carry out unauthorised work or improvise any arrangements or adopt short cut method or misuse any of the facilities provided in pursuance of the Schedule, in such a manner as to cause risk to themselves as well as or to others employed. (f) The workers shall not refuse undergoing medical examination as required under these rules. Atomic Energy Factory Rules, 1996 149 Rule 88(Sch.II) PART IX No women shall be employed in the processes covered under Appendix 'A' PART X EXEMPTIONS 1. Power of Exemption.- The Government or subject to the control of the Government, the Competent Authority may exempt from the compliance with any of the requirements of this Schedule partly or fully, any factory carrying out processes covered in Appendix 'A', if it is clearly and satisfactorily established by the occupier that the compliance with any of the requirement is not necessary to ensure the safety and health of persons employed and/or suitable and effective alternate arrangements are available to any of the requirements covered in this schedule. Appendix A Any works or that part of works in which – (a) The manufacture, manipulation or recovery of the following is carried on:- (i) sodium, potassium, iron, aluminium, cobalt, nickel, copper, arsenic, antimony, chromium, zinc, selenium, magnesium, cadmium, mercury, beryllium and their organic and inorganic salts, alloys, oxides and hydroxides; (ii) ammonia, ammonium hydroxide and salts of ammonium; (iii) the organic or inorganic compounds of sulphurous, sulphuric, nitric, nitrous, hydrochloric, hydrofluoric, hydriodic, hydrosulphuric, hydrobromic, boric; (iv) cyanogen compounds, cyanide compounds, cyanate compounds; (v) phosphorous and its compounds other than organo phosphorous insecticides; and (vi) chlorine. (b) Hydrogen sulphide is evolved by the decomposition of metallic sulphides, or hydrogen sulphide is used in the production of such sulphides. (c) Bleaching powder is manufactured or chlorine gas is produced in chlor-alkali plants. Atomic Energy Factory Rules, 1996 150 Rule 88(Sch.II) (d) (i) gas tar or coal tar or bitumen or shale oil asphalt or any residue of such tar is distilled or is used in any process of chemicals manufacture; and (ii) tar based synthetic colouring matters or their intermediates are produced. (e) Nitric acid is used in the manufacture of nitro compounds. (f) Explosives are produced with the use of nitro compounds. (g) Aliphatic or aromatic compounds or their metallic and non-metallic derivatives or substituted derivatives, such as chloroform, ethylene glycol, formaldehyde, benzyl chloride, phenol, methyl ethyl ketone peroxide , cobalt carbonyl, tungsten carbide etc. are manufactured or recovered. Appendix B Concerning Special Bathing Accommodation in pursuance of Para 4 of Part VII. 1. Nitro or amino processes 2. All chrome processes 3. Processes of distilling gas or coal tar or processes of chemical manufacture in which tar is used. 4. Processes involving manufacture, manipulation, handling or recovery of cyanogen compound, cyanide compound, cyanate compounds. 5. Processes involving manufacture of bleaching powder or production of chlorine gas in chloralkali plants. 6. Manufacture, manipulation or recovery of nickel and its compounds. 7. All processes involving the manufacture, manipulation or recovery of aliphatic or aromatic compounds or their derivatives or substituted derivatives. Appendix C Ambulance :- Ambulance shall have the following equipments : Atomic Energy Factory Rules, 1996 151 Rule 88(Sch.II) General :- - A wheeled stretcher with folding and adjusting devices; Head of the stretcher must be capable of being tilted upward; - Fixed suction unit with equipments; - Fixed oxygen supply with equipments; - Pillow with case; - Sheets; - Blankets; - Towels; - Emesis bag; - Bed pan; - Urinal; - Glass. Safety equipment:- - Flares with life of 30 minutes - Flood lights; - Flash lights; - Fire extinguisher dry powder type; - Insulated gauntlets. Emergency care equipments:- Resuscitation:- - Portable suction unit; - Portable oxygen unit; - Bag-valve-mask, hand operated artificial ventilation unit; - Airways; - Mouth gags; Atomic Energy Factory Rules, 1996 152 Rule 88(Sch.II) - Tracheotomy adaptors; - Short spine board; - I.V. Fluids with administration unit; - B.P. monitor; - Cugg; - Stethoscope. Immobilization:- - Long & short padded boards; - Wire ladder splints; - Triangular bandage; - Long & short spine boards. Dressings:- - Gauze pads - 10 cm x 19 cm ; - Universal dressing -25 cm X 90 cm ; - Roll of aluminium foils; - Soft roller bandages 15 cm X 5 m ; - Adhesive tape in 7.5 cm roll; - Safety pins; - Bandage sheets; - Burn sheet. Poisoning:- - Syrup of Ipecac; | - Activated charcoal; Prepacketed in doses - Snake bite kit; - Drinking water. Emergency Medicines:- Atomic Energy Factory Rules, 1996 153 Rule 88(Sch.II-III) - As per requirement (under the advice of Medical Officer only) SCHEDULE III MANIPULATION OF STONE OR ANY OTHER MATERIAL CONTAINING FREE SILICA 1. Application.- This schedule shall apply to all factories or parts of factories in which manipulation of stone or any other material containing free silica is carried on. 2. Definitions.- For the purpose of this Schedule - (a) "manipulation" means crushing, breaking, chipping, dressing, grinding, sieving, mixing, grading or handling of stone or any other material containing free silica or any other operation involving such stone or material (b) "stone or any other material containing free silica" means a stone or any other solid material containing not less than 5% by weight of free silica. 3. Precautions in manipulation.- No manipulation shall be carried out in a factory or part of a factory unless one or more of the following measures, namely - (a) damping the stone or other material being processed, (b) providing water spray, (c) enclosing the process, (d) isolating the process, and (e) providing localised exhaust ventilation, are adopted so as to effectively control the dust in any place in the factory where any person is employed, at a level equal to or below the maximum permissible level for silica dust as laid down in Second Schedule of section 41 F Provided that such measures as above said are not necessary if the process or operation itself is such that the level of dust created and prevailing does not exceed the permissible level referred to. 4. Maintenance of floors.- (a) All floors or places where fine dust is likely to settle on and where on any person has to work or pass shall be of impervious material and maintained in such condition that they can be thoroughly cleaned by a moist method or any other method which would prevent dust being airborne in the process of cleaning. Atomic Energy Factory Rules, 1996 154 Rule 88(Sch.III) (b) The surface of every floor of every work room or place where any work is carried on or where any person has to pass during the course of his work, shall be cleansed of dust once at least during each shift after being sprayed with water or by any other suitable method so as to prevent dust being airborne in the process of cleaning. 5. Medical facilities and records of examinations and tests.- (a) The occupier of every factory to which the schedule applies, shall - (i) employ a qualified medical officer for medical surveillance of the worker employed therein whose employment shall be subject to the approval of the Competent Authority; and (ii) provide to the said medical officer all the necessary facilities for the purpose referred to in clause (i). (b) The record of medical examination and appropriate tests carried out by the said medical officer shall be maintained in a separate register in form 1A and shall be kept readily available for inspection by the Inspector. 6. Medical examination by Certifying Surgeon.- (a) Every worker employed in the processes specified in paragraph 1, shall be examined by a Certifying Surgeon within 15 days of his first employment. Such medical examination shall include pulmonary function tests and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (b) Every worker employed in the said processes shall be re- examined by a Certifying Surgeon at least once in every twelve months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub- paragraph (a) except chest X-ray which will be once in 3 years. (c) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 1 . The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the Manager of the factory. The record of each examination carried out under sub-paragraphs (a) and (b), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 1A. (d) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Inspector. Atomic Energy Factory Rules, 1996 155 Rule 88(Sch.III-IV) (e) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents shall also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (f) No person who has been found unfit to work as said in sub-paragraph (e) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 7. Exemptions.- If in respect of any factory, the Competent Authority is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule are not necessary for protection of the workers in the factory, the Competent Authority may by a certificate in writing, which he may in his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. SCHEDULE IV GRINDING OR GLAZING OF METALS AND PROCESSES INCIDENTAL THERETO 1. Exception.- (a) Nothing in this schedule shall apply to any factory in which only repairs are carried on except any part thereof in which one or more persons are wholly or mainly employed in the grinding or glazing of metals. (b) Nothing in this schedule except paragraph 4 shall apply to any grinding or glazing of metals carried on intermittently and at which no person is employed for more than 12 hours in any week. 2. Definitions.- For the purposes of this schedule - (a) grindstone" means a grindstone composed of natural or manufactured sandstone but does not include a metal wheel or cylinder into which blocks of natural or manufactured sandstone are fitted; (b) "abrasive wheel" means a wheel manufactured of bonded Atomic Energy Factory Rules, 1996 156 Rule 88(Sch.IV) emery or similar abrasive; (c) "grinding" means the abrasion, by aid of mechanical power, of metal, by means of a grindstone or abrasive wheel; (d) "glazing" means the abrading, polishing or finishing, by aid of mechanical power, of metal, by means of any wheel, buff, mop or similar appliance to which any abrading or polishing substance is attached or applied; (e) "racing" means the turning up, cutting or dressing of a revolving grindstone before it is brought into use for the first time; (f) "hacking" means the chipping of the surface of a grindstone by a hack or similar tool; and (g) "rodding" means the dressing of the surface of a revolving grindstone by the application of a rod, bar or strip of metal to such surface. 3. Equipment for removal of dust.- No racing, dry grinding or glazing shall be performed without - (a) a hood or other appliance so constructed, arranged, placed and maintained as substantially to intercept the dust thrown off; (b) a duct of adequate size, air tight and so arranged as to be capable of carrying away the dust, shall be kept free from obstruction and shall be provided with proper means of access for inspection and cleaning, and where practicable, with a connection at the end remote from the fan to enable the Inspector to attach thereto any instrument necessary for ascertaining the pressure of air in the said duct; and (c) a fan or other efficient means of producing a draught sufficient to extract the dust: Provided that the Competent Authority may accept any other appliance that is, in his opinion, as effective for the interception, removal and disposal of dust thrown off as a hood, duct and fan would be. 4. Restriction on employment on grinding operations.- Not more than one person shall at any time perform the actual process of grinding or glazing upon a grindstone, abrasive wheel or glazing appliance: Provided that this paragraph shall not prohibit the employment of persons to assist in the manipulation of heavy or Atomic Energy Factory Rules, 1996 157 Rule 88(Sch.IV) bulky articles at any such grindstone, abrasive wheel or glazing appliance. 5. Glazing.- Glazing or other processes, except processes incidental to wet grinding upon a grindstone shall not be carried on in any room in which wet grinding upon a grindstone is done. 6. Hacking and rodding.- Hacking or rodding shall not be done unless during the process either an adequate supply of water is laid on at the upper surface of the grindstone or adequate appliances for the interceptions of dust are provided in accordance with the requirements of paragraph 3. 7. Examination of dust equipment.- (a) All equipment for the extraction or suppression of dust shall at least once in every six months be examined and tested by a competent person, and any defect disclosed by such examination and test shall be rectified as soon as practicable. (b) A register containing particulars of such examination and tests shall be kept in Form 10. 8. Medical facilities and record of examinations and tests.- (a) The occupier of every factory in which grinding or glazing of metals are carried out, shall - (i) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose appointment shall be subject to the approval of the Competent Authority ; and (ii) provide to the said medical practitioner all the necessary facilities for the purpose referred to in the sub-paragraph (i) above. (b) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register in Form 1A and which shall be kept readily available for inspection by the Competent Authority. 9. Medical examination by Certifying Surgeon.- (a) Every worker employed in grinding or glazing of metal and processes incidental thereto shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function tests and in suspected cases chest X-rays. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (b) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 12 Atomic Energy Factory Rules, 1996 158 Rule 88(Sch.IV-V) calendar months. Such re-examination shall, wherever the Certifying Surgeon considers appropriate, include tests as specified in sub-paragraph(a). (c) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 1. The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (a) and (b),including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 1A. (d) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Competent Authority. (e) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents shall also include the period for which he considers that the said person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person affected shall be suitably rehabilitated. (f) No person who has been found unfit to work as said in sub-paragraph (e) shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 10. Exemption.- The Competent Authority may by certificate in writing, subject to such conditions as he may specify therein, relax or suspend any of the provisions of this schedule in respect of any factory if owing to the special methods of work or otherwise such relaxation or suspension is practicable without danger to the health or safety of the persons employed. SCHEDULE V HANDLING OR MANIPULATION OF CORROSIVE SUBSTANCES 1. Definitions.- For the purposes of this schedule - (a) "corrosive operation" means an operation of manufacturing, storing, handling, processing, packing, or using Atomic Energy Factory Rules, 1996 159 Rule 88(Sch.V) any corrosive substance in a factory; and (b) "corrosive substance" includes sulphuric acid, nitric acid, hydrochloric acid, hydrofluoric acid, carbolic acid, phosphoric acid, liquid chlorine, liquid bromine, ammonia, sodium hydroxide and potassium hydroxide and a mixture thereof, and any other substance which the Competent Authority will notify to be a corrosive substance. 2. Flooring.- The floor of every workroom of a factory in which corrosive operation is carried on shall be made of impervious, corrosion and fire resistant material and shall be so constructed as to prevent collection of any corrosive substance. The surface of such flooring shall be smooth and cleaned as often as necessary and maintained in a sound condition. 3. Protective equipment.- (a) The occupier shall provide for the use of all persons employed in any corrosive operation suitable protective wear for hands and feet, suitable aprons, face shields, chemical safety goggles, and respirators. The equipments shall be maintained in good order and shall be kept in clean and hygienic condition by suitably treating to get rid of the ill effects of any absorbed chemicals and by disinfecting. The occupier shall also provide suitable protective creams and other preparations wherever necessary. (b) The protective equipment and preparations provided shall be used by the persons employed in any corrosive operation. 4. Water facilities.- Where any corrosive operation is carried on, there shall be provided as close to the place of such operation as possible, an eyewash fountain or a source of clean water at a height of 210 cm. from a pipe of 1.25 cm. diameter and fitted with a quick acting valve so that in case of injury to the worker by any corrosive substance, the injured part can be thoroughly flooded with water. Wherever necessary, in order to ensure continuous water supply a storage tank having a minimum length, breadth and height of 210 cm., 120 cm. and 60 cms respectively or such dimensions as are approved by the Competent Authority shall be provided as the source of clean water. 5. Cautionary notice.- A cautionary notice in the following form and printed in the language which majority of the workers employed understand, shall be displayed prominently close to the place where a corrosive operation is carried out and where it can be easily and conveniently read by the workers. If any worker is illiterate, effective steps shall be taken to explain carefully to him the contents of the notice so displayed. Atomic Energy Factory Rules, 1996 160 Rules 88(Sch.V) CAUTIONARY NOTICE DANGER Corrosive substances cause severe burns and vapours thereof may be extremely hazardous. In case of contact, immediately flood the part affected with plenty of water for at least 15 minutes. Get medical attention quickly. 6. Transport.- (a) Corrosive substances shall not be filled, moved or carried except in containers or through pipes and when they are to be transported in containers, they shall be placed in crates of sound construction and of sufficient strength. (b) A container with a capacity of 11.5 litres or more of a corrosive substance shall be placed in a receptacle or crate and then carried by more than one person at a height below the waist line unless a suitable rubber wheeled truck is used for the purpose. (c) Containers for corrosive substances shall be plainly labeled. 7. Devices for handling corrosives.- (a) Suitable tilting, lifting or pumping arrangements shall be used for emptying jars, carboys and other containers of corrosives. (b) Corrosive substance shall not be handled by bare hands but by means of a suitable scoop or other device. 8. Opening of valves.- Valves fitted to containers holding a corrosive substance shall be opened with great care. If they do not work freely, they shall not be forced open. They shall be opened by a worker suitably trained for the purpose. 9. Cleaning tanks, stills, etc.- (a) In cleaning out or removing residues from stills or other large chambers used for holding any corrosive substance, suitable implements made of wood or other material shall be used to prevent production of arseniuretted hydrogen (arsine). (b) Whenever it is necessary for the purpose of cleaning or other maintenance work for any worker to enter chamber, tank, vat, pit or other confined space where a corrosive substance had been stored, all possible precautions required under section 36 of the Act shall be taken to ensure the worker's safety. Atomic Energy Factory Rules, 1996 161 Rule 88(Sch.V-VI) (c) Wherever possible, before repairs are undertaken to any part of equipment in which a corrosive substance was handled, such equipment or part thereof shall be freed of any adhering corrosive substance by adopting suitable methods. 10. Storage.- (a) Corrosive substances shall not be stored in the same room with other chemicals, such as turpentine, carbides, metallic powders and combustible materials, the accidental mixing with which may cause a reaction which is either violent or gives rise to toxic fumes and gases. (b) Pumping or filling overhead tanks, receptacles, vats or other containers for storing corrosive substances shall be so arranged that there is no possibility of any corrosive substance overflowing and causing injury to any person. (c) Every container having a capacity of twenty litres or more and every pipeline, valve and fitting used for storing or carrying corrosive substances shall be thoroughly examined every year for finding out any defects. Defects so found out shall be removed forthwith. A register shall be maintained of every such examination made and shall be produced before the Competent Authority whenever required. 11. Fire Extinguishers and fire fighting equipment.- An adequate number of suitable type of fire extinguishers or other fire fighting equipment, depending on the nature of chemicals stored, shall be provided. Such extinguishers or other equipment shall be regularly tested and refilled. Clear instructions as to how the extinguishers or other equipment should be used printed in the language which majority of the workers employed understand, shall be affixed near each extinguisher or other equipment. 12. Exemption.- If in respect of any factory on an application made by the manager, the Competent Authority is satisfied that owing to the exceptional circumstances, or the infrequency of the process or for any other reason to be recorded by it in writing, all or any of the provisions of this schedule are not necessary for the protection of the persons employed therein, it may by a certificate in writing, which it may at any time revoke, exempt the factory from such of the provisions and subject to such conditions as it may specify therein. SCHEDULE VI FOUNDRY 1. Application.- Provisions of this schedule shall apply to all parts of factories where any of the following operations or processes are carried on: Atomic Energy Factory Rules, 1996 162 Rule 88(Sch.VI) (a) the production of iron castings or, as the case may be, steel casings by casting in moulds made of sand, loam, moulding composition or other mixture of materials, or by shell moulding, or by centrifugal casting and any process incidental to such production; (b) the production of non-ferrous castings by casting metal in moulds made of sand, loam, metal, moulding composition or other material or mixture of materials, or by shell mouldings, die-casting (including pressure die casting), process incidental to such production; and (c) the melting and casting of non-ferrous metal for the production of ingots, billets, slabs or other similar products, and the stripping thereof; but shall not apply with respect to - (i) any process with respect to the smelting and manufacture of lead and the Electric Accumulators; (ii) any process for the purposes of a printing works; or (iii) any smelting process in which metal is obtained by a reducing operation or any process incidental to such operation; or (iv) the production of steel in the form of ingots; or (v) any process in the course of the manufacture of solder or any process incidental to such manufacture; or (vi) the melting and casting of lead or any lead-based alloy for the production of ingots, billets, slabs or other similar products or the stripping thereof, or any process incidental to such melting, casting or stripping. 2. Definition.-For the purpose of this schedule- (a) "approved respirator" means a respirator of a type approved by the Competent Authority; (b) "cupola or furnace" includes a receiver associated therewith; (c) "dressing of fettling operations" includes stripping and other removal of adherent sand, cores, runners, risers, flash and other surplus metal from a casting and the production of reasonably clean and smooth surface, but does not electrical heaters in the case of electrically heated ovens or furnaces. (d) "foundry" means those parts of a factory in which the production of iron or steel or nonferrous castings(not being the Atomic Energy Factory Rules, 1996 163 Rule 88(Sch.VI) production of steel in the production of pig iron or the production of steel in the form of ingots) is carried on by casting in moulds made of sand, loam, moulding composition or by centrifugal casting in metal moulds lined with sand, or die casting including pressure die castings, together with any part of the factory in which any of the following processes are carried on as incidental processes in connection with and in the course of, such production, namely, the preparation and mixing of materials used in foundry process, the preparation of moulds and cores, knockout operations and dressing or fettling operations; (e) "knock-out operations" means all methods of removing castings from moulds and the following operations, castings from moulds and the following operations, when done in connection therewith, namely, stripping, coring-out and the removal of runners and risers; (f) "pouring aisle" means as aisle leading from a main gangway or directly from a cupola or furnace to where metal is poured into moulds. 3. Prohibition of use of certain materials as parting materials .- (a) A material shall not be used as a parting material if it is a material containing compounds of silicon calculated as silica to the extent more than 5 percent by weight of the dry material : Provided that this prohibition shall not prevent the following being used as a parting material if the material does not contain an admixture of any other silica - (i) Zirconium silicate (Zircon). (ii) Calcined china clay. (iii) Calcined aluminous fireclay. (iv) Sillimanite. (v) Calcined or fused alumina. (vi) Olivine. (vii) Natural sand. (b) Dust or other matter deposited from a fettling or blasting process shall not be used as a parting material or as a constituent in a parting material. 4. Arrangement and storage.- For the purposes of promoting safety and cleanliness in workrooms the following requirements shall be observed - Atomic Energy Factory Rules, 1996 164 Rule 88(Sch.VI) (a) moulding boxes, loam plates, laddles, patterns, pattern plates, frames, boards, box weights, and other heavy articles shall be so arranged and placed as to enable work to be carried on without unnecessary risk; (b) suitable and conveniently accessible racks, bins or other receptacles shall be provided and used for the storage of other gear and tools; (c) where there is bulk storage of sand, fuel, metal scrap or other materials or residues, suitable bins, bunkers or other receptacles shall be provided for the purpose of such storage. 5. Construction of floors.- (a) Floors of indoor workplaces in which the processes are carried on, other than parts which are of sand, shall have an even surface of hard material. (b) No part of the floor of any such indoor workplace shall be of sand except where this is necessary by reason of the work done. (c) All parts of the surface of the floor of any such indoor workplace which are of sand shall, so far as practicable, be maintained in an even and firm condition. 6. Cleanliness of indoor workplaces.- (a) All accessible parts of the walls of every indoor workplace in which the processes are carried on and of everything affixed to those wall shall be effectively cleaned by a suitable method to a height of not less than 4.2 m from the floor at least once in every period of fourteen months. A record of the carrying out of every such effective cleaning in pursuance of this paragraph including the date (which shall be not less than five months nor more than nine months after the last immediately preceding washing, cleaning or other treatment). (b) Effective cleaning by a suitable method shall be carried out at least once every working day of all accessible parts of the floor of every indoor workplace in which the processes are carried on, other than parts which are of sand; and the parts which are of sand shall be kept in good order. 7. Manual operations involving molten metal.- (a) There shall be provided and properly maintained for all persons employed on manual operations involving molten metal with which they are liable to be splashed, a working space for that operation - (i) which is adequate for the safe performance of the work and Atomic Energy Factory Rules, 1996 165 Rule 88(Sch.VI) (ii) which, so far as reasonably practicable, is kept free from obstruction. (b) Any operation involving the carrying by hand of a container holding molten metal shall be performed on a floor all parts of which where any person walks while engaged in the operation shall be on the same level: Provided that, where necessary to enable the operation to be performed without undue risk, nothing in this paragraph shall prevent the occasional or exceptional use of a working space on a different level from the floor, being a space provided with a safe means of access from the floor for any person while engaged in the operation. 8. Gangways and pouring aisles.- (a) In every workroom to which this paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule and , so far as reasonably practicable, in every other workroom to which this paragraph applies, sufficient and clearly defined main gangways shall be provided and properly maintained which - (i) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; (ii) shall be kept, so far as reasonably practicable, free from obstruction; (iii) if not used for carrying molten metal, shall be at least 920 mm wide; and (iv) if used for carrying molten metal shall be - (1) where truck ladles are used exclusively, at least 600 mm wider than the overall width of the ladle; (2) where hand shanks are carried by not more than two men, at least 920 mm in width; (3) where hand shanks are carried by more than two men, at least 1.2 m in width; and (4) where used for simultaneous travel in both directions by men carrying hand shanks, at least 1.8 m in width. (b) In workroom to which this Paragraph applies constructed, reconstructed or converted for use as such after the making of this Schedule, sufficient and clearly defined pouring aisles Atomic Energy Factory Rules, 1996 166 Rule 88(Sch.VI) shall be provided and properly maintained which - (i) shall have an even surface of hard material and shall, in particular, not be of sand or have on them more sand than is necessary to avoid risk of flying metal from accidental spillage; (ii) shall be kept so far as reasonably practicable free from obstruction; (iii) if molten metal is carried in hand ladles or bull ladles by not more than two men per ladle, shall be at least 460 mm wide, but where any moulds alongside the aisle are more than 510 mm above the floor of the aisle, the aisle shall be not less than 600 mm wide; (iv) if molten metal is carried in hand ladles or bull ladles by more than two men per ladle, shall be at least 760 mm wide; and (v) if molten metal is carried in crane, trolley or truck ladles, the same shall be of a width adequate for the safe performance of the work. (c) Requirements of sub-paragraph (a) & (b) shall not apply to any workroom or part of a workroom if, by reason of the nature of the work done therein, the floor of that workroom or, as the case may be, that part of a workroom has to be of sand. (d) In this Paragraph "workroom to which this Paragraph applies" means a part of a ferrous or non-ferrous foundry in which molten metal is transported or used, and a workroom to which this paragraph applies shall be deemed for the purposes of this Paragraph to have been constructed, reconstructed or converted for use as such after the making of this Schedule if the construction, reconstruction or conversion thereof was begun after the making of this Schedule. 9. Work near cupolas and furnaces.- No person shall carry out any work within a distance of 4 m from a vertical line passing through the delivery end of any spout of a cupola or furnace, being a spout used for delivering molten metal, or within a distance of 2.4 m from a vertical line of any ladle which is in position at the end of such a spout, except in either case, where it is necessary for the proper use of maintenance of a cupola or furnace that work shall be carried out within that distance or that work is being carried out at such a time and under such conditions that there is no danger to the person carrying it out from molten metal which is being obtained from the cupola or furnace or is in a ladle in position at the end of the spout. Atomic Energy Factory Rules, 1996 167 Rule 88(Sch.VI) 10. Dust and fumes.- (a) Open coal, coke or wood fires shall not be used for heating or drying ladles inside a workroom unless adequate measures are taken to prevent, so far as practicable, fumes or other impurities from entering into or remaining in the atmosphere of the workroom. (b) No open coal, coke or wood fires shall be used for drying moulds except in circumstances in which the use of such fires is unavoidable. (c) Mould stoves, core stoves and annealing furnaces shall be so designed constructed, maintained and worked as to prevent, so far as practicable, offensive or injurious fumes from entering into any workroom during any period when a person is employed therein. (d) All knock-out operations shall be carried out - (i) in a separate part of the foundry suitably partitioned off, being a room or part in which, so far as reasonably practicable, effective and suitable local exhaust ventilation and a high standard of general ventilation are provided; or (ii) in an area of the foundry in which, so far as reasonably practicable, effective and suitable local exhaust ventilation is provided, or where compliance with this requirement is not reasonably practicable, a high standard of general ventilation is provided. (e) All dressing or fettling operations shall be carried out - (i) in a separate room or in a separate part of the foundry suitably partitioned off; or (ii) in an area of the foundry set apart for the purpose; and shall, so far as reasonably practicable, be carried out with effective and suitable local exhaust ventilation or other equally effective means of suppressing dust, operating as near as possible to the point of origin of the dust. 11. Maintenance and examination of exhaust plant.- (a) All ventilating plants used for the purpose of extracting, suppressing or controlling dust or fumes shall be properly maintained. (b) All ventilating plants used for the purpose of extracting, suppressing or controlling dust or fumes shall be examined and inspected once every week by a responsible person. Atomic Energy Factory Rules, 1996 168 Rule 88(Sch.VI) It shall be thoroughly examined and tested by a competent person at least once in every period of twelve months; and particulars of the results of every such examination and test shall be entered in Form 10 which shall be available for inspection by an inspector. Any defect found on any such examination and test shall be immediately reported in writing by the person carrying out the examination and test to the occupier or manager of the factory. 12. Protective Equipment.- (a) The occupier shall provide and maintain suitable protective equipment specified for the protection of workers- (i) suitable gloves or other protection for the hands for workers engaged in handling any hot material likely to cause damage to the hands by burn, scald or scar, or in handling pig iron, rough castings or other articles likely to cause damage to the hands by cut or abrasion; (ii) approved respirators for workers carrying out any operations creating a heavy dust concentration which cannot be dispelled quickly and effectively by the existing ventilation arrangements. (b) No respirator provided for the purposes of clause (a)(ii)has been worn by a person shall be worn by another person if it has not since been thoroughly cleaned and disinfected. (c) Persons who for any of their time - (i) work at a spout of or attend to, a cupola or furnace in such circumstances that material there from may come into contact with the body, being material at such a temperature that its contact with the body would cause a burn; or (ii) are engaged in, or in assisting with, the pouring of molten metal; or (iii) carry by hand or move by manual power any ladle or mould containing molten metal; or (iv) are engaged in knocking-out operations involving material at such a temperature that its contact with the body would cause a burn; shall be provided with suitable footwear and gaiters which when worn by them prevent, so far as reasonably practicable, risk or burns to his feet and ankles. (d) Where appropriate, suitable screens shall be provided for protection against flying materials (including splashes of Atomic Energy Factory Rules, 1996 169 Rule 88(Sch.VI) molten metal and sparks and chips thrown off in the course of any process). (e) The occupier shall provide and maintain suitable accommodation for the storage and make adequate arrangements for cleaning and maintaining of the protective equipment supplied in pursuance of this paragraph. (f) Every person shall make full and proper use of the equipment provided for his protection in pursuance of subparagraphs (a) and (d) and shall without delay report to the occupier, manager or other appropriate person any defect in, or loss of, the same. 13. Washing and bathing facilities.- (a) There shall be provided and maintained in clean state and good repair for the use of all workers employed in the foundry - (i) a wash place under cover with either - (1) a trough with impervious surface fitted with a waste pipe without plug, and of sufficient length to allow at least 60 cm for every 10 such persons employed at any one time and having a constant supply of clean water from taps or jets above the trough at intervals of not more than 60 cm.; or (2) at least one tap or stand pipe for every 10 such persons employed at any one time, and having a constant supply of clean water, the tap or stand pipe being spaced not less than 1.2 m apart; and (ii) not less than one half of the total number of washing places provided under sub-para (i) above, shall be in the form of bath rooms. (iii) a sufficient supply of clean towels made of suitable material changed daily, with sufficient supply of nail brushes and soap. (b) The facilities provided for the purposes of sub- paragraph (a) shall be placed in charge of a responsible person or persons and maintained in a clean and orderly condition. 14. Disposal of dross and skimmings.- Dross and skimmings removed from molten metal or taken from a furnace shall be placed forthwith in suitable receptacles. 15. Disposal of waste.- Appropriate measures shall be taken for the disposal of all waste products from shell moulding (including waste burnt sand) as soon as reasonably practicable after the Atomic Energy Factory Rules, 1996 170 Rule 88(Sch.VI) castings have been knocked-out. 16. Material and equipment left out of doors.- All material and equipment left out of doors (including material sand equipment so left only temporarily or occasionally) shall be so arranged and placed as to avoid unnecessary risk. There shall be safe means of access to all such material and equipment and, so far as reasonably practicable, such access shall be by roadways or pathways shall have a firm and even surface and shall, so far as reasonably practicable be kept free from obstruction. 17. Medical facilities and records of examinations and tests.- (a) The occupier of every factory to which the Schedule applies, shall- (i) employ a qualified medical practitioner for medical surveillance of the workers employed therein whose employment shall be subject to the approval of the Competent Authority ; and (ii) provide to the said medical practitioner all the necessary facilities for the purpose referred to in sub- paragraph (i) above. (b) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register -Form 1A- which shall be kept readily available for inspection by the Competent Authority. 18. Medical examination by Certifying Surgeon.- (a) Every worker employed in a foundry shall be examined by a Certifying Surgeon within 15 days of his first employment. Such medical examination shall include pulmonary function tests and chest X- ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (b) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every twelve months. Such examination shall, wherever the Certifying Surgeon considers appropriate, include all the tests as specified in sub- paragraph (a) except chest X-ray which will be once in 3 years. (c) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 1 . The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried out under sub-paragraphs (a) and (b), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 1A. Atomic Energy Factory Rules, 1996 171 Rule 88(Sch.VI-VII) (d) The Certificate of Fitness and the health register shall be kept readily available for inspection by an inspector. (e) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in the said certificate and documents shall also include the period for which he considers that the said person is unfit for work in the said processes. (f) No person who has been found unfit to work as said in sub-paragraph(e) above shall be re-employed or permitted to work in the said processes unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 19. Exemption.- If in respect of any factory, the Competent Authority is satisfied that owing to the exceptional circumstances or infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Competent Authority may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. SCHEDULE VII ELECTRICAL WORK & ELECTRICAL INSTALLATIONS 1. Scope. This schedule covers safety procedures and practices in electrical work, fire safety of electrical installations and transformer protection. 2. Permit-to work system.- (a) All work on major electrical installations shall be carried out under permit-to- work system, unless standing instructions are issued by the competent authority to follow other procedures. In extenuating circumstance, such as for the purpose of saving life or time in the event of an emergency, it may become necessary to start the work without being able to obtain the necessary permit-to-work; in such cases, the action taken shall be reported to the person-in-charge as soon as possible. The permit-to-work certificate from the person-in-charge of operation to the person-in- charge of the men selected to carry out any particular work ensures that portion of the installation where the work is to be carried out is rendered dead and safe for working. All work shall be carried out under the personal supervision of a competent person. If more than one department is working on the same apparatus, a Atomic Energy Factory Rules, 1996 172 Rule 88(Sch.VII) permit-to-work shall be issued to the person-in-charge of each department. (b) No work shall be commenced on live mains unless it is specifically intended to be so done by specially trained staff. In such cases all possible precautions shall be taken to ensure the safety of the staff engaged for such work, and also of others who may be directly or indirectly connected with the work. Such work shall only be carried out with proper equipment provided for the purpose and, after taking necessary precautions, by specially trained and experienced persons who are aware of the danger that exists when working on or near live mains or apparatus. (c) On completion of the work for which the permit-to-work is issued, the person-in- charge of the maintenance staff should return the permit duly discharged to the issuing authority. (d) In all cases, the issue and return of permits shall be recorded in a special register provided for that purpose. (e) The permits shall be issued not only to the staff of the supply under takings, but also to the staff of other departments, contractors, engineers, etc, who might be required to work adjacent to live electrical mains or apparatus. (f) Permit books shall be treated as important records. All sheets in the permit books and the books themselves shall be serially numbered. No page shall be detached or used for any other except bonafide work. If any sheet is detached, a dated and initialed statement shall then and there be recorded in the book by the person responsible for it. (g) Permit books shall be kept only by the person-in-charge of operations who shall maintain a record of the receipts and issues made by him. 3. Safety instructions.- (a) Safety Instructions for Working on Mains and Apparatus up to and including 650V- (i) Work on Dead, Low and Medium Voltage Mains and Apparatus - Unless a person is authorised to work on live mains and apparatus all mains and apparatus to be worked upon shall be isolated from all sources of supply before starting the work, proved dead, earthed and short-circuited. For earthing and short-circuiting, measures shall be taken against the inadvertent energizing of the mains and apparatus. (ii) Work on Live Mains and Apparatus - Only competent, experienced and authorized persons shall work on live mains Atomic Energy Factory Rules, 1996 173 Rule 88(Sch.VII) and apparatus, and such persons shall take all safety measures as may be required. Warning boards shall be attached on or adjacent to the live apparatus and at the limits of the zone in which work may be carried out. Immediately before starting work, rubber gauntlets, if used, shall be thoroughly examined to see whether they are in sound condition. Under no circumstances shall a person work with unsound gauntlets, mats, stools, platforms or other accessories and safety devices. No live part shall be within unsafe distance of a person working on live low and medium voltage mains so that he does not come in contact with it unless he is properly protected. (iii) Testing of Mains and Apparatus - No persons shall apply test voltage to any mains unless he has received a permit-to work and has warned all persons working on the mains of the proposed application of test voltage. If any part which will thus become alive is exposed, the person in- charge of the test shall take due precautions to ensure that the exposed live portion does not constitute danger to any person. It shall also be ensured before the application of test voltage, that no other permit-to-work has been issued for working on this mains. (iv) Connecting Dead Mains to Live Mains - When dead mains are connected to live mains, all connections to the live parts shall be made last, and in all cases the phase sequence shall be checked to ensure that only like phases are connected together. Before inserting fuses or links in a feeder or distribution pillar controlling the cable on which a fault has been cleared, each phase shall first be connected through a test switch fuse. (b) Safety Instructions for Working on Mains and Apparatus at Voltages Above 650V- (i) General - All mains and apparatus shall be regarded as live and a source of danger and treated accordingly, unless it is positively known to be dead and earthed. (ii) No person shall work on, test or earth mains or apparatus unless covered by a permit-to-work and after proving the mains dead, except for the purpose of connecting the testing apparatus, etc. which is specially designed for connecting to the live parts. Atomic Energy Factory Rules, 1996 174 Rule 88(Sch.VII) (iii) The operations of proving dead, earthing and short- circuiting of any mains shall be carried out only by an authorized person under the instructions of the person-in- charge of maintenance; (iv) While working on mains, the following precautions shall be taken: (1) No person, after receiving a permit-to-work, shall work on, or in any way interfere with, any mains or conduits or trough containing a live mains except under the personal instructions, and supervision, on the site of work, of competent person; (2) When any live mains is to be earthed, the procedure prescribed in 3(e) shall be scrupulously followed; and (3) The earths and short-circuits, specified on the permit-to-work shall not be removed or interfered with except by authority from the person-in-charge of the work. (c) Minimum Working Distance - No person shall work within the minimum working distance from the exposed live mains and apparatus. The minimum working distance depends upon the actual voltages. It does not apply to operations carried out on mains and apparatus which are so constructed as to permit safe operation within these distances. Exposed live equipment in the vicinity shall be cordoned off. The cordoning off shall be done in such a way that it does not hinder the movement of the maintenance personnel. If necessary, a safety supervisor shall be posted. (d) Isolation of Mains - Isolation of mains shall be effected by the following methods: (i) The electrical circuits shall be broken only by authorized persons by disconnecting switches, isolating links, unbolting connections or switches which are racked out. Where possible, the isolation shall be visibly checked; and (ii) Where the means of isolation are provided with a device to prevent their reclosure by unauthorised persons, such a device shall be used. (e) Devices for Proving Mains and Apparatus Dead: (i) High voltage neon lamp contact indicator rods fitted with an indicating neon tube or other means which glows when the contact end of the rod comes in contact with exposed Atomic Energy Factory Rules, 1996 175 Rule 88(Sch.VII) live parts and is clearly marked for the maximum voltage on which it may be safely used and shall not, under any circumstances, be used on higher voltages; (ii) Contact indicator and phasing rods are provided for phasing and proving exposed mains and apparatus dead. Each set, consisting of two rods, is normally marked for the maximum voltage on which it may be used and shall not, under any circumstances, be used on higher voltages; (iii) Use of Contact Indicator and Phasing Rods - While using the high voltage contact indicator and phasing rods for proving the mains or apparatus dead, following precautions shall be taken- (1) Ensure that the rod is clean and dry; (2) Check the rod by applying it to known live parts of the correct voltage, the indicating tube shall glow; (3) Apply the rod to each phase required to be proved dead, the indicating tube shall not glow. Be very careful to be in a position to see the glow, if any, appearing in the indicating tube; and (4) Again check the rod by applying it to live parts as in (2) above, again the indicating tube shall glow; (iv) Testing and marking of devices - It shall be ensured that all devices for proving high voltage mains and apparatus dead are marked clearly with the maximum voltage for which they are intended and shall be tested periodically; (v) Identification of cables to be worked upon - A cable shall be identified as that having been proved dead prior to cutting or carrying out any operation which may involve work on or movement of the cable. A non-contact indicating rod, induction testing set or spiking device may be used for proving the cable dead; (vi) Earthing and short-circuiting mains - (1) High voltage mains shall not be worked upon unless they are discharged to earth after making them dead and are earthed and short-circuited with earthing and short- circuiting equipment adequate to carry possible short- circuit currents and specially meant for the purpose. All earthing switches wherever installed shall be locked up; (2) If a cable is required to be cut, a steel wedge Atomic Energy Factory Rules, 1996 176 Rule 88(Sch.VII) shall be carefully driven through it at the point where it is to be cut or preferably by means of a spiking gun of approved design; (3) After testing the cable with dc voltage, the cable shall be discharged through a 2 mega ohms resistance and not directly, owing to dielectric absorption which is particularly prominent in the dc voltage testing of high voltage cables. The cable shall be discharged for a sufficiently long period to prevent rebuilding up of voltage; (4) The earthing device when used shall be first connected to an effective earth. The other end of the device shall then be connected to the conductors to be earthed; and (5) Except for the purpose of testing, phasing, etc. the earthing and short-circuiting devices shall remain connected for the duration of the work; (vii) Removing the earth connections - On completion of work, removal of the earthing and short-circuiting devices shall be carried out in the reverse order to that adopted for placing them(see 3(b)(vi) that is, the end of the earthing device attached to the conductors of the earthed mains or apparatus shall be removed first and the other end connected to earths shall be removed last. The conductor shall not be touched after the earthing device has been removed from it; (viii) Safety precautions for earthing - The precautions mentioned below shall be adopted to the extent applicable and possible- (1) Examine earthing devices periodically and always prior to their use; (2) Use only earthing switches or any other special apparatus where provided for earthing; (3) Verify that the circuit is dead by means of discharging rod or potential indicator. The indicator itself shall first be tested on a live circuit before and after the verification; (4) Earthing shall be done in such a manner that the persons doing the job are protected by earth connections on both sides of their working zone; and Atomic Energy Factory Rules, 1996 177 Rule 88(Sch.VII) (5) All the three phases shall be effectively earthed and short- circuited though work may be proceeding on one phase only; (ix) Working on mains where visible isolation cannot be carried out- Where the electrical circuit cannot be broken visibly as set out in [3.(d)] the circuit may be broken by two circuit opening devices, one on each side of the work zone, where duplicate feed is available and by one circuit opening device where duplicate feed is not available provided the following conditions are fulfilled: (1) The position of the contacts of the circuit opening device(s) - 'open' or 'closed' - is clearly indicated by the position of the operating handle or by signal lights or by other means. (2) The circuit opening device(s) can be locked mechanically in the open position. (3) The mains and apparatus to be worked on are adequately earthed and short-circuited between the circuit opening device and the position of the work. (4) In cases where duplicate feed is available, both the circuit opening devices are in series between the mains and any source of supply. (5) In cases where duplicate feed is not available, the circuit opening device is between the mains to be worked on and any source of supply. The circuit opening devices mentioned above shall be locked in the open position before the work on the mains and apparatus is commenced. The locking devices shall be removed only by a competent person and not until the work has been completed. Any short-circuiting and earthing shall be removed and the permit-to-work form duly returned and canceled. (x) Work on mains with two or more sections - When the mains to be worked upon are to be divided into two or more sections, the provisions of 3(d) and 3(e)(vi) and 3(e)(ix) shall be observed with regard to each section. 4. Safety practices.- In all electrical works, safety practices as prescribed in relevant Indian national standards shall be observed. 5. Safety posters.-The owner of every medium, high and extra high voltage installation is required to fix permanently, in a Atomic Energy Factory Rules, 1996 178 Rule 88(Sch.VII) conspicuous position a danger notice in Hindi or English and the local language on every motor, generator, transformer, all supports of high and extra high voltage etc. The danger notice plate shall contain symbols and shall conform to national standards. 6. Accidents and treatment for electric shock.- First-aid provisions & First-aid trained persons shall be available in the factory to take care of emergencies due to accidents. Reference may be made to relevant national standards in this respect. 7. Fire safety of electrical installations.- (a) General- Electrical installations in any plant consist of pumps, motors, diesel generator sets with oil tanks, circuit breakers, transformers interconnected with thousands of metres of power & instrumentation cables running on matrix of cable trays separated from each other by distance and carrying large number of cables. It is a good practice to avoid cable joints in the plant area. The cables have invariably to penetrate walls & floorings. A defence in depth approach against fires shall be employed by adequate balance in - (i) preventing fires from starting; (ii) detecting & extinguishing quickly such fires as do get started & limiting their damage; and (iii) designing the plant to minimise the effect of fires on essential functions. (b) Cables & Cable Trays - Only those cables which are qualified for normal operation, for operation during design basis events & passing specified flame tests as per relevant standards shall only be used. Cable trays shall be separated by appropriate physical distance from each other & floor and ceilings taking into account fire spread characteristics of the cables , cable ventilation requirements & also electromagnetic interference requirements. (c) Cable Penetration Sealants, Fire Retardant Spray, Fire barriers- These shall be used whenever the cables penetrate walls, ceiling or floorings within a plant. The penetrations shall be closed and sealed with fire retardant sealing material from both sides. In addition the cables shall be coated with fire retardant material to a distance of at least 30 cm on both sides of the penetration. Fire barriers shall be provided at distances of every 25 m. (d) Housekeeping-Proper housekeeping procedures shall be drawn to see that flammable liquids, combustible materials & Atomic Energy Factory Rules, 1996 179 Rule 88(Sch.VII) dust are not allowed to accumulate in cable trays & cable spread room. (e) Fire detection & annunciation system - Combination of ionization & optical type of flame detectors in adequate numbers shall be used taking into account ventilation pattern in the area. Line detectors shall be used in special areas like cable vaults and cable spread rooms. A separate fire annunciation panel with both audio & visual annunciation shall be provided for each zone. In addition one central panel for all the fire zones shall be provided in the control room. (f) CCTV Monitoring System - A close circuit TV Monitoring system be preferably used for continuous monitoring of unmanned areas from the control room. (g) Personnel & Equipment Protection - Electrical Fires in general give out toxic or corrosive fumes which attack both man & equipment. Proper personnel protective gear such as self contained breathing apparatus, fire retardant clothing, eye protection gear shall be made available in adequate numbers. Electrical & electronic equipments shall be properly cleaned after the fire so as to remove the effects of corrosive fumes & fire extinguishing materials. (h) Periodic Inspection & Testing - A detailed program to inspect & test the electrical installations shall be established as per the relevant standards & rules. 8. Transformer protection.- (a) Design - The design, construction & manufacture shall comply with all currently applicable statutes, regulations and safety codes in the locality where the transformer will be installed. The reliability of a transformer shall be given first consideration, the principal factors being- (i) sound mechanical construction (ii) adequate oil ducts and electrical clearances. (iii) Current and flux densities such as to avoid local heating. (iv) Liberal radiating surfaces. (v) Good oil. Relevant national standards and Indian Electricity Rules,1956 shall be referred to. Atomic Energy Factory Rules, 1996 180 Rule 88(Sch.VII) (b) Acceptance - A transformer shall be subjected to following tests at the manufacturing end before its acceptance. (i) routine tests - All transformers are subjected to following tests: (1) voltage ratio & polarity. (2) winding resistance. (3) impedance voltage, short-circuit impedance and load loss. (4) dielectric tests (5) no load losses & current. (6) on-load changes, where appropriate. (ii) Type tests -These are meant for complying with specified requirements and not covered under routine tests: (1) temperature rise test. (2) lightning impulse tests. (iii) Special tests - These are other than routine or type tests as agreed between manufacturer & purchaser: (1) dielectric tests, (2) zero sequence impedance on 3 phase transformer, (3) short-circuit test, (4) acoustic sound level test, (5) Harmonics on the no-load current, (6) Power taken by fan and oil pump motors. (c) Installation & Commissioning - The transformer shall be so installed that there is no risk of anyone receiving an electric shock. Although with all metal parts of the metal tank bound together and properly earthed, the tank may be considered quite safe, yet consideration shall be given to the arrangement of the connections. If two or more transformers are installed side by side, they shall be separated by fire-separation walls. Fire separation Atomic Energy Factory Rules, 1996 181 Rule 88(Sch.VII) walls are adequate from fire-safety point of view, if oil capacity of individual transformers do not exceed 2000 litres and total capacity of all transformers installed side by side exceeds 2000 litres. For indoor transformers, oil soak pits shall be provided under the transformer or outside the transformer room. The tests to be carried out at site before commissioning the transformer will depend upon the voltage and KVA rating of the transformer, facilities available at site and conditions of contracts. Following are the typical tests to be carried out: (i) general inspection, (ii) secondary injection, (iii) primary injection, (iv) ratio tests, (v) tripping tests, (vi) earth resistance, (vii) Buchholtz relay. (viii) alarm circuits. (ix) fans & pumps. (x) tap changing tests to check mechanism, indication, buzzer lamp etc. (xi) phasing tests. (xii) insulation tests. (xiii) site test for oil (xiv) voltage compensation tests. (xv) neutral earthing switches are closed before alive. (xvi) check for transformers on equal taps before switching on. (xvii) set down relays before closing in - advise control. (xviii) if necessary, arrange temporary protection for soaking & switching on. Atomic Energy Factory Rules, 1996 182 Rule 88(Sch.VII) (xix) set up relays after soaking & before going on load. (xx) load tests. (xxi) tap changing test on load over full range of taps. (xxii) advise control of any main equipment commissioned. (xxiii) low voltage excitation current. (xxiv) single-phase, magnetic balance test. (d) Maintenance - Detailed inspection & maintenance schedule shall be drawn & implemented depending on the size of transformer, importance of service continuity, the location of the system and operating conditions such as ambient temp., unusually dirty atmosphere, heavy fogs and water supply (in case of water- cooled units). The supply authority shall be consulted if heavy loads on single phase or unbalanced loads are to be connected. (i) maintenance schedules for all types of transformers of rating less than 1000 KVA and for ratings of 1000 KVA and above shall be as per relevant BIS standards. The hourly and daily inspections are applicable to attended sub- stations only. However, for unattended sub-stations, these items shall be inspected as frequently as practicable. (ii) Faults observed during the periodic maintenance schedules shall be rectified as per relevant BIS standard. (e) Standard Safety requirements - Following points shall be observed as standard safety requirements with respect to fire and electrical hazards of a transformer. (i) Transformers shall be located preferably outside the buildings and when so located shall be surrounded by an enclosure of metal fencing at least 2.5 M high or isolated by elevation. Where building walls form a part of such enclosures, any opening there in shall be screened or barred. In addition, oil filled transformers shall be suitably isolated from such building walls by approved fire resistant materials or adequate distances. (ii) Oil filled transformers located inside buildings shall be placed in ventilated fireproof vaults provided with raised door sills, locked fire resistant doors, air vents that close automatically in the event of the fire and an appropriate automatic fire extinguishing arrangement as per relevant standards. Atomic Energy Factory Rules, 1996 183 Rule 88 (Sch.VIII) SCHEDULE VIII BERYLLIUM OPERATIONS 1. Work on beryl ore, beryllium and its compounds involves risk of air contamination. Hence they shall be carried out in a specially designed totally enclosed facility, consisting of dust extraction & suppression system, with bare minimum use of manual operation. Use of Beryllium rooms shall be restricted solely to beryllium work. A central monitoring room shall be set up to monitor the vital parameters of the process. All stocks of beryllium and its compounds shall be kept in a fire proof store. A fire & fumes detection & alarm system shall be provided. 2. The worker exposure to beryllium and its compounds in the workplace shall be controlled by requiring compliance with the rules set forth in the following paragraphs. 3. Environmental (workplace ) air concentration.- (a) No worker shall be exposed at his place of employment to a concentration of beryllium more than two micrograms of total airborne particulate beryllium per cubic meter of air (2 µg Be/m3) (determined by the breathing-zone and general air methods) , determined as a time- weighted average (TWA) exposure for an 8-hour work day as stipulated in the second schedule of the Act. (b) Sampling and Analysis - Procedures for sampling, calibration of equipment, and analysis of beryllium samples shall be as per relevant standards. (c) Medical - (i) Medical surveillance of the worker shall be continued up to 20 years from the cessation of the work or his death whichever is earlier. (ii) A comprehensive pre-placement history and physical examination for all workers shall be provided to include as a minimum a 38cm X 43cm chest X-ray, baseline pulmonary function [forced vital capacity (FVC) and forced expiratory volume at one second (FEV1.0)], and a baseline weight. (iii) Each worker exposed to beryllium shall receive an annual examination that includes: (1) Spirometry, including FVC and FEV1.0. (2) A medical history questionnaire that includes presence and degree of respiratory symptoms, that is breathlessness, cough, sputum production, and wheezing. (3) A 38 cm X 43 cm chest X-ray Atomic Energy Factory Rules, 1996 184 Rule 88(Sch.VIII) (d) Competent Authority; Inspector; & medical inspector shall have access to medical records. (e) Medical records shall be maintained for at least 20 years. 4. Labeling.- (a) The following precautionary label shall be applied to all shipping and storage containers or packages containing beryllium and beryllium compounds where exposures to dusts, fumes, powders, or liquids are likely to occur. BERYLLIUM (Name of Compound) Dust, Fume, Powder, or Liquid DANGER Harmful If Inhaled and May Cause Immediate or Delayed Injury Use Only With Adequate Local Exhaust Ventilation and Approved Respiratory and Personal Protective Devices May Cause Rash or External Ulcers Wash Thoroughly After Handling (b) The following warning sign shall be affixed in a readily visible location on processing and other equipment, on storage bins and tanks, and at or near entrances and areas where exposure to dusts or fumes of beryllium and its compounds are likely to occur. DANGER Beryllium Dust (or Fume) Areas UNAUTHORIZED PERSONS KEEP OUT Breathing Dust (Or Fumes) May Cause Immediate or Delayed Injury 5. Personal Protective Equipment and Clothing.- (a) Respiratory Devices.- (i) Respiratory protective devices shall be used any time the actual or projected level of beryllium will exceed an 8-hour Atomic Energy Factory Rules, 1996 185 Rule 88(Sch.VIII) time-weighted average concentration of 2 ug/m3. These devices shall not be used as a substitute for proper engineering controls, but are appropriate for necessary periods where excessive atmospheric concentrations result from emergencies or from maintenance or repair. (ii) Standard procedures shall be established for respirator use to include the following: (1) Procedures established for respirator usage shall insure that no worker is exposed to beryllium in excess of the standard because of improper respirator selection or face piece fit. (2) Facepiece fit shall be checked by the wearer each time he puts on the respirator. (iii) The respirator used shall be of the appropriate class as determined on the basis of the actual or projected atmospheric concentration of airborne beryllium at the worksite where the respirator is to be used as follows: (1) Reusable half mask air purifying respirators equipped with high efficiency filters shall be used in atmospheres containing not more than 25 µg Be/m3 for any period of time. (2) Reusable full-facepiece air purifying respirators equipped with high efficiency filters shall be used in atmospheres containing not more than 100 µg Be/m3 for any period of time. (3) Powdered air purifying respirators equipped with high efficiency filters, operating with positive pressure during the inhalation phase of breathing shall be used in atmospheres containing not more than 1000 µg Be/m3. When equipped with a "fume filter," respirators shall be used in atmospheres containing not more than 40 µg Be/m3. (4) Continuous flow air-line respirators or self-contained breathing units operating in the pressure-demand mode and providing positive pressure during the inhalation phase of breathing, shall be used in atmospheres that exceed 1000 µg Be/m3. (iv) An effective respirator program to include selection, use, maintenance and care, special problems, and effective respirator program evaluation shall be established. Compliance with the requirements of the latest BIS standards for respiratory protection shall be implemented. (b) Protective Clothing Atomic Energy Factory Rules, 1996 186 Rule 88(Sch.VIII) (i) Beryllium Exposed Workers (1) The employer shall provide each employee except those with minimal exposure with protective clothing, headgear, and shoes when the employee must work with and/or be exposed to beryllium, beryllium compounds, or beryllium containing products. (2) Such clothing may be coveralls or similar full body protective clothing. (3) Protective shoecovers or work shoes shall be worn during the working hours in areas where there is exposure to beryllium. (4) Resin-impregnated paper or similar protective clothing can be substituted for fabric-type clothing. (5) Protective clothing shall be changed at least each day at the end of each shift. (6) The employer shall provide for maintenance and laundering of soiled protective clothing, which shall be stored, transported, and disposed of in sealed, non-reusable containers and labeled with easy-to-read letters as outlined in paragraph 4. (7) Dust removal, by blowing or shaking of clothing, shall be prohibited; protective clothing shall be cleaned by power suction (vacuum) prior to removal; removal of contaminated clothing shall be allowed only in the change rooms. (8) The employer shall provide laundering controls and inform the employee and any party inhouse or otherwise which launders contaminated clothing, of the potentially harmful effects of exposure to beryllium dust and of safe practices required in the laundering of beryllium-soiled work clothing. (ii) Workers with Minimum Beryllium Exposure (1) The employer shall provide laboratory coats or equivalent protective clothing to each such employee who works with or is exposed to beryllium, beryllium compounds, or beryllium containing products. (2) Clean protective clothing shall be supplied to each worker at least weekly. 6. Appraisal of Employees of Hazards from Beryllium.- (a) Each employee exposed to beryllium shall be apprised of all hazards, adverse symptoms of overexposure, appropriate emergency procedures, and proper conditions and precautions for safe use or exposure, to include as a minimum, all information as set forth Atomic Energy Factory Rules, 1996 187 Rule 88(Sch.VIII) in Form 9 which is applicable to that specific product or material containing beryllium to which he is exposed. (b) The information shall be maintained on file and readily accessible to the worker at all places of employment where beryllium is involved in unit processes and operations. (c) Information as specified in Form 9 titled 'Material Safety Data Sheet' shall be recorded. 7. Work Practices.- (a) Emergency Procedures- (i) Procedures, including fire fighting procedures, shall be established and implemented to meet foreseeable emergency events, including those involving massive release of beryllium contaminants. (1) Where there is the possibility of massive beryllium contamination from accidents involving elevated temperature operations or large scale spills, a general alarm, drench-type showers, and cleansing facilities shall be installed in such a manner as to provide prompt, immediate access by any employee; respirators shall be available for wearing during evacuation procedures if long distances need to be traversed; and full- facepiece or supplied-air respirators shall be available for employee use where equipment or operations cannot be abandoned. If large scale spills occur, careful monitoring of beryllium air levels shall be instituted as soon as practicable. Determinations shall be made as to when it is safe to re-enter a contaminated area with respiratory protection and to resume operations without respiratory protection. Thoroughly supervised cleanup operations shall be instituted as soon as air levels recede to the point where operations may be conducted. (2) Full-face piece or supplied-air respirators shall be kept ready for emergency use. They shall be inspected after each use and at least monthly to assure satisfactory working condition. Where used, air and oxygen cylinders shall be fully charged according to the manufacturer's instructions. (3) Sand, soda ash, or commercial metal fire extinguishment powder shall be available for use as an extinguishing agent for beryllium; water and carbon dioxide shall not be used. (ii) Exhaust Systems - Procedures shall be established to reduce exposure to airborne beryllium through implementation of adequate ventilation methods. Local exhaust and collection shall be designed and maintained to prevent the accumulation of beryllium dust and fumes. A report on examination & test of dust extraction & suppression system shall be maintained in Form 10 and be kept available for inspection. Atomic Energy Factory Rules, 1996 188 Rule 88(Sch.VIII) (iii) General Housekeeping- (1) No dry sweeping shall be performed. (2) Emphasis shall be placed upon cleanup of spills, periodic repair of equipment and leaks, and proper storage of materials to prevent breakage. (iv) Disposal - Beryllium waste and scrap shall be collected and disposed of in sealed bags or other sealed containers. Scrap shall be recycled or shall be disposed of by burial. (v) Non-Worker Access to Beryllium Areas - Entry to any area where there is the possibility of exposure to beryllium shall be permitted only on the basis of need and all persons so entering shall be provided with the same protective clothing as required for employees regularly assigned to that area. (vi) Educational Program - An educational program shall be instituted for all workers to include proper instruction in maintenance procedures, cleanup methods, and use of respiratory protective devices and protective clothing. 8. Sanitation Practices.- (a) Food Facilities - Food preparation and eating shall be prohibited in beryllium work areas. (b) Locker and Toilet Facilities - (i) Separate locker facilities shall be provided for work clothes and street clothes. (ii) Showers for exposed workers shall be required following a work shift and prior to putting on street clothes. (iii) Locker-shower facilities shall be so arranged that the showers can serve to demarcate between potentially "clean" and "contaminated" areas. (iv) Suitable provisions shall be made for the control of contaminated dust in workshop storage and clothing hanger locations. (v) Handwashing and toilet facilities shall be arranged so that following use, workers need not re-enter a potentially contaminated area. 9. Monitoring and Recordkeeping Requirements.- (a) Employers shall maintain record of environmental exposures to beryllium based upon the following sampling and recording schedule: (i) Quarterly requirements- Atomic Energy Factory Rules, 1996 189 Rule 88(Sch.VIII-IX) (1) Breathing-zone samples shall be collected from employees at least quarterly for specific work operations. It is recognised that sampling frequency is dependent upon the process and emissions; the quarterly sampling frequency is primarily for production operations. (2) Samples shall be collected and evaluated as both time- weighted and peak concentration values. (ii) Thirty-Day Requirements - The sampling regime shall be every 30 days for work areas under the following conditions: (1) The environmental time-weighted average or peak concentrations are in excess of the standards. (2) Sampling, monitoring, and recordkeeping requirements of a 30-day schedule shall be required only until two consecutive 30-day sampling periods have resulted in environmental levels which meet the standard. (b) Records shall be maintained for all sampling schedules to include the type of personal protective devices, if any, in use. (c) Workers shall be informed of the periodic results of samplings. SCHEDULE IX ZIRCONIUM OPERATIONS 1. Work on zirconium and its compounds involves risk of fire, as such, it shall be carried out in a specially designed facility. Use of such facilities shall be restricted only for zirconium work. A suitable notice shall be displayed at the entrance prohibiting the entry of unauthorised personnel. 2. Surface of plant/laboratories and store shall be designed to prevent accumulation of zirconium powder. 3. Source of ignition shall be excluded from the zirconium handling areas. The design for these areas shall include lightning protection and means to prevent accumulation of static electric charge. 4. Electrical equipment installed in these areas shall be of approved explosion proof type. 5. Wherever zirconium powder may be formed, a local exhaust system shall be provided. The duct shall be as short as Atomic Energy Factory Rules, 1996 190 Rule 88 (Sch.IX-X) possible. It shall be free from sharp bends and dead space and shall have proper means of access for inspection and cleaning. 6. A high standard of cleanliness shall be maintained throughout the zirconium handling areas. Wet mopping shall be adopted for cleaning. Mops used for cleaning shall be stored always under water. 7. The design of plant/laboratories shall make adequate provision for the safe storage of zirconium powder, sludges, sponges or scrap. 8. Containers for product or waste shall be metallic and labeled. They shall not be exposed to extremes of temperature. 9. Zirconium wastes containing sludges, sponge or scrap shall be stored separately from any other waste material. They shall be stored under water (minimum 15 cm.). Safe procedures shall be formulated for the collection, transportation, storage and disposal taking into account the pyrophoricity of the material. 10. Disposal of powder waste shall be done by incineration under controlled conditions by trained personnel at a suitable place designated for the purpose. 11. Waste liquid containing zirconium in suspension shall be treated by a process which removes the suspended zirconium, before discharging. 12. Fire-fighting appliances shall be provided in all the areas. Operations involving zirconium shall never remain unattended. SCHEDULE X FINISHING BY ABRASIVES PROPELLED BY COMPRESSED AIR/STEAM Cleaning or Smoothening, Roughening, etc., of Articles, by a Jet of Sand, Metal Shot, or Grit, or other Abrasive Propelled by a Blast of Compressed Air or Steam: 1. Definition.- For the purposes of this Schedule (a) "blasting" means cleaning, smoothening, roughening, or removing of any part of the surface of any article by the use as an abrasive of a jet of sand, metal shot, or grit or other material, propelled by a blast of compressed air or steam; (b) "blasting enclosure" means a chamber, barrel, cabinet or any other enclosure designed for the performance of blasting therein; Atomic Energy Factory Rules, 1996 191 Rule 88 (Sch.X) (c) "blasting chamber" means a blasting enclosure in which any person may enter at any time in connection with any work or otherwise; and (d) "cleaning of castings" where done as an incidental or supplemental process in connection with the making of metal castings, means the freeing of the casting from adherent sand or other substance and includes the removal of cores and the general smoothening of a casting, but does not include the free treatment. 2. Prohibition of sand blasting.- Sand or any other substance containing free silica shall not be introduced as an abrasive into any blasting apparatus and shall not be used for blasting: Provided further that no woman shall be employed or permitted to work at any operation of sand blasting. 3. Precautions in connection with blasting operations.- (a) Blasting shall not be done except in a blasting enclosure and no work other than blasting and any work immediately incidental thereto and clearing and repairing of the enclosure including the plant and appliances situated therein, shall be performed in a blasting enclosure. Every door, aperture and joint of blasting enclosure, shall be kept closed and air-tight while blasting is being done therein. (b) Blasting enclosure shall always be maintained in good condition and effective measures shall be taken to prevent dust escaping from such enclosure, and from apparatus connected therewith, into the air of any room. (c) There shall be provided and maintained for and in connection with every blasting enclosure, efficient apparatus for separating, so far as practicable, abrasive which has been used for blasting and which is to be used again as an abrasive, from dust or particles of other materials arising from blasting; and no such abrasive shall be introduced into any blasting apparatus and used for blasting until it has been so separated: Provided that this clause shall not apply, except in the case of blasting chambers, to blasting enclosures constructed or installed before the coming into force of this schedule, if the Competent Authority is of opinion that it is not reasonably practicable to provide such separating apparatus. (d) There shall be provided and maintained in connection with every blasting enclosure efficient ventilating plant to extract, by exhaust draught effected by mechanical means, dust produced in the enclosure. The dust extracted and removed shall Atomic Energy Factory Rules, 1996 192 Rule 88(Sch.X) be disposed of by such method and in such manner that it shall not escape into the air of any room; and every other filtering or settling device situated in a room in which persons are employed, other than persons attending to such bag or other filtering or settling device, shall be completely separated from the general air of that room in an enclosure ventilated to the open air. (e) The ventilating plant provided for the purpose of sub-paragraph (d) shall be kept in continuous operation whenever the blasting enclosure is in use whether or not blasting is actually taking place therein, and in the case of a blasting chamber, it shall be in operation even when any person is inside the chamber for the purpose of cleaning. 4. Inspection and examination.- (a) Every blasting enclosure shall be specially inspected by a competent person at least once in every week in which it is used for blasting enclosure, the apparatus connected therewith and the ventilating plant shall be thoroughly examined and in the case of ventilating plant, tested by a competent person at least once in every month. (b) Particulars of the result of every such inspection, examination or test shall forthwith be entered in a register which shall be kept in Form 10 and shall be available for inspection by any workman employed in or in connection with blasting in the factory. Any defect found on any such inspection, examination or test this paragraph applies shall be deemed for the purposes of this Paragraph to have been constructed, reconstructed or converted for use as such after the making of this Schedule if the construction, reconstruction or conversion thereof was begun after the making of this Schedule. 5. Provision of protective helmets, gauntlets and overalls.- (a) There shall be provided and maintained for the use of all persons who are employed in a blasting chamber, whether in blasting or in any work connected therewith or in cleaning such a chamber, protective helmets of a type approved by a certificate of the Competent Authority; and every such person shall wear the helmet provided for this use whilst he is in the chamber and shall not remove it until he is outside the chamber. (b) Each protective helmet shall carry a distinguishing mark indicating the person by whom it is intended to be used and no person shall be allowed or required to wear a helmet not carrying his mark or a helmet which has been worn by another person and has not since been thoroughly disinfected. (c) Each protective helmet when in use shall be supplied with clean and not unreasonably cold air at a rate of not less than 170 litres per minute. Atomic Energy Factory Rules, 1996 193 Rule 88(Sch.X) (d) Suitable gauntlets and overalls shall be provided for the use of all persons while performing blasting or assisting at blasting, and every such person shall while so engaged, wear the gauntlet and overall provided. 6. Precautions in connection with cleaning and other work - (a) Where any person is engaged upon cleaning of any blasting apparatus or blasting enclosure or of any apparatus or ventilating plant connected therewith or the surroundings thereof or upon any other work in connection with any blasting apparatus or blasting enclosure or with any apparatus or ventilating plant connected therewith so that he is exposed to the risk of inhaling dust which has arisen from blasting, all practicable measures shall be taken to prevent such inhalation. (b) In connection with any cleaning operation referred to in paragraph 5, and with the removal of dust from filtering or settling devices all practicable measures shall be taken to dispose of the dust in such a manner that it does not enter the air of any room. Vacuum cleaners shall be provided and used wherever practicable for such cleaning operations. 7. Storage accommodation for protective wear.- Adequate and suitable storage accommodation for the helmets, gauntlets and overalls required to be provided by paragraph 5 shall be proved outside and conveniently near to every blasting enclosure and such accommodation shall be kept clean. Helmets and overalls when not in actual use shall be kept in this accommodation. 8. Maintenance and cleaning of protective wear.- All helmets, gauntlets, overalls and other protective devices or clothings provided and worn for the purposes of this schedule, shall be kept in good condition and so far as is reasonably practicable shall be cleaned on every weekday in which they are used. Where dust arising from the cleaning of such protective clothing or devices is likely to be inhaled, all practicable measures shall be taken to prevent such inhalation. Vacuum cleaners shall, wherever practicable, be used for removing dust from such clothing and compressed air shall not be used for removing dust from any clothing. 9. Maintenance of vacuum cleaning plant.- Vacuum cleaning plant used for the purpose of this schedule shall be properly maintained. 10. Medical facilities and records of examinations and tests.- (a) The occupier of every factory to which the Schedule applies, shall (i) employ a qualified medical practitioner for medical surveillance of the workers employed therein, and whose Atomic Energy Factory Rules, 1996 194 Rule 88(Sch.X) employment shall be subject to the approval of the Competent Authority; and (ii) provide to the said medical practitioner all the necessary facilities for the purpose referred to in clause (i) above. (b) The record of medical examinations and appropriate tests carried out by the said medical practitioner shall be maintained in a separate register approved by the Competent Authority which shall be kept readily available for inspection by the Inspector. 11. Medical examination by Certifying Surgeon.- (a) Every worker employed in any of the processes to which this schedule applies shall be examined by a Certifying Surgeon within 15 days of his first employment. Such examination shall include pulmonary function test and chest X-ray. No worker shall be allowed to work after 15 days of his first employment in the factory unless certified fit for such employment by the Certifying Surgeon. (b) Every worker employed in the said processes shall be re-examined by a Certifying Surgeon at least once in every 12 calendar months and such re-examination shall, wherever the Certifying Surgeon considers appropriate, include pulmonary function test and chest X-ray once in every three years. (c) The Certifying Surgeon after examining a worker, shall issue a Certificate of Fitness in Form 1 .The record of examination and re-examinations carried out shall be entered in the Certificate and the Certificate shall be kept in the custody of the manager of the factory. The record of each examination carried under sub- paragraphs (a) and (b), including the nature and the results of the tests, shall also be entered by the Certifying Surgeon in a health register in Form 1A. (d) The Certificate of Fitness and the health register shall be kept readily available for inspection by the Competent Authority. (e) If at any time the Certifying Surgeon is of the opinion that a worker is no longer fit for employment in the said processes on the ground that continuance therein would involve special danger to the health of the worker, he shall make a record of his findings in the said certificate and the health register. The entry of his findings in those documents shall also include the period for which he considers that the said person is unfit for work in the said processes. The person so suspended from the process shall be provided with alternate placement facilities unless he is fully incapacitated in the opinion of the Certifying Surgeon, in which case the person Atomic Energy Factory Rules, 1996 195 Rule 88(Sch.X-XI) affected shall be suitably rehabilitated. (f) No person who has been found unfit to work in the said processes as said in sub- paragraph (e) above shall be reemployed or permitted to work unless the Certifying Surgeon, after further examination, again certifies him fit for employment in those processes. 12. Power to exempt or relax.- (a) If the Competent Authority is satisfied that in any factory or any class of factories, the use of sand or other substance containing free silica as an abrasive in blasting is necessary for a particular manufacture or process (other than the process incidental or supplemental to making of metal castings) and that the manufacture or process cannot be carried on without the use of such abrasive or that owing to the special conditions or special method of work or otherwise any requirement of this schedule can be suspended either temporarily or permanently, or can be relaxed without endangering the health of the persons employed or that application of any of such requirements is for any reason impracticable or inappropriate, it may, with the previous sanction of the Central Government, by an order in writing exempt the said factory or class of factories from such provisions of this schedule, to such an extent and subject to such conditions and for such period as may be specified in the said order. (b) Where an exemption has been granted under sub-paragraph (a), a copy of the order shall be displayed at a notice board at a prominent place at the main entrance or entrances to the factory and also at the place where the blasting is carried on. SCHEDULE XI OPERATIONS INVOLVING HIGH NOISE LEVELS 1. Application.- This schedule shall apply to all operations in any manufacturing process having high noise level. 2. Definitions.- (a) "Noise" means any unwanted sound. (b) "High noise level" means any noise level measured on the A-weighted scale is 90 dB or above. (c) "Decibel" means one-tenth of "Bel" which is the fundamental division of a logarithmic scale used to express the ratio of two specified or implied quantities, the number of "Bels" denoting such a ratio being the logarithm to the base of 10 of this ratio. The noise level (or the sound pressure level) Atomic Energy Factory Rules, 1996 196 Rule 88 (Sch.XI) corresponds to a reference pressure of 20 micro-newtons per square meter or 0.0002 dynes per sq.cm. which is the threshold of hearing in average healthy listeners. (d) "Frequency" is the rate of pressure variations expressed in cycles per second or hertz. (e) "dBA" refers to sound level in decibels as measured on a sound level meter operating on the A weighting network with slow meter response. (f) "A-weighting" means making graded adjustments in the intensities of sound of various frequencies for the purpose of noise measurement, so that the sound pressure level measured by an instrument reflects the actual response of the human ear to the sound measured. 3. Protection against noise.- (a) In every factory, suitable engineering control or administrative measures shall be taken to ensure, so far as is reasonably practicable, that no worker is exposed to sound levels exceeding the maximum permissible noise exposure levels specified in Tables 1 & 2. Atomic Energy Factory Rules, 1996 197 Rule 88(Sch.XI) Table 1 Permissible Exposure in Cases of Continuous Noise Total time of exposure (continuous or a number of short term exposures) per day, in hours. sound pressure level in dBA 1 2 8 90 6 92 4 95 3 97 2 100 3/2 102 1 105 3/4 107 1/2 110 1/4 115 Note : 1. No exposure in excess of 115 dBA is to be permitted. 2. For any period of exposure falling between any figure and the next higher or lower figure as indicated in column 1,the permissible sound pressure level is to be determined by extrapolation on a proportionate basis. Table 2 Permissible Exposure Levels of Impulsive or Impact Noise Peak sound pressure level in dB Permitted number of impulses or impacts per day 1 2 140 100 135 315 Atomic Energy Factory Rules, 1996 198 Rule 88(Sch.XI) Peak sound pressure level in dB Permitted number of impulses or impacts per day 1 2 130 1,000 125 3,160 120 10,000 Note : 1. No exposure in excess of 140 dB peak sound pressure level is permitted. 2. For any peak sound pressure level falling in between any figure and the next higher or lower figure as indicated in column 1,thepermitted number of impulses is to be determined by extrapolation on a proportionate basis. (b) For the purposes of this schedule, if the variations in the noise level involve maxima at intervals of one second or less, the noise is to be considered as a continuous one and the criteria given in Table 1 would apply. In other cases, the noise is to be considered as impulsive or impact noise and the criteria given in Table 2 would apply. (c) When the daily exposure is composed of two or more periods of noise exposure at different levels their combined effect should be considered, rather than the individual effect of each. The mixed exposure should be considered to exceed the limit value if the sum of the fractions C1/T1 + C2/T2 + ...........Cn/Tn > 1 Where the C1, C2 etc. indicate the total time of actual exposure at a specified noise level and T1, T2, etc. denote the time of exposure permissible at that level. Noise exposure of less than 90 dBA may be ignored in the above calculation. (d) Where it is not possible to reduce the noise exposure to the levels specified in sub- rule (a) by reasonably practicable engineering control or administrative measures, the noise exposure shall be reduced to the greatest extent feasible by such control measures, and each worker so exposed shall be provided with suitable ear protectors so as to reduce the exposure to noise to the levels specified in sub- rule(a). (e) Where the ear protectors provided in accordance with sub-paragraph (b) and worn by a worker cannot still attenuate the noise reaching near his ear, as determined by subtracting the Atomic Energy Factory Rules, 1996 199 Rule 88(Sch.XI-XII) attenuation value in dBA of the ear protectors concerned from the measured sound pressure level, to a level permissible under Table 1 or Table 2 as the case may be, the noise exposure period shall be suitably reduced to correspond to the permissible noise exposures specified in sub-paragraph (a). (f) (i) In all cases where the prevailing sound levels exceed the permissible levels specified in sub-paragraph(a) there shall be administered an effective hearing conservation programme which shall include among other hearing conservation measures, pre-employment and periodical auditory surveys conducted on workers exposed to noise exceeding the permissible levels, and rehabilitation of such workers either by reducing the exposure to the noise levels or by transferring them to places where noise levels are relatively less or by any other suitable means. (ii) Every worker employed in areas where the noise exceeds the maximum permissible exposure levels specified in sub- rule (a) shall be subjected to an auditory examination by a Certifying Surgeon within 14 days of his first employment and thereafter, shall be re-examined at least once every 12 months. Such initial and periodical examinations shall include tests which the Certifying Surgeon may consider appropriate, and shall include determination of auditory thresholds for pure tones of 125, 250, 500, 1000, 2000, 4000, and 8000 Hz. SCHEDULE XII HIGHLY FLAMMABLE LIQUIDS AND FLAMMABLE COMPRESSED GASES 1. Application.- These rules will be applicable to all factories where highly flammable liquids or flammable compressed gases are manufactured, stored, handled or used. 2. Definition.- For the purpose of this Schedule - (a) "highly flammable liquid" means any liquid including its solution, emulsion or suspension which when tested in a manner specified by sections 14 and 15 of the Petroleum Act, 1934, (30 of 1934) gives off flammable vapours at a temperature less than 32 degrees Celsius; (b) "flammable compressed gas" means flammable compressed gas as defined in rule 2 of the Static and Mobile Pressure Vessels (Unfired) Rules 1981 framed under the Explosives Act, 1884. Atomic Energy Factory Rules, 1996 200 Rule 88 (Sch.XII) 3. Storage.- (a) Every flammable liquid or flammable compressed gas used in every factory shall be stored in suitable fixed storage tank, or in suitable closed vessel located in a safe position under the ground, in the open or in a store room of adequate fire resistant construction. (b) Except as necessary for use, operation or maintenance, every vessel or tank which contains or had contained a highly flammable liquid or flammable compressed gas shall be always kept closed and all reasonably practicable steps shall be taken to contain or immediately drain off to a suitable container any spill or leak that may occur. (c) Every container, vessel, tank, cylinder, or store room used for storing highly flammable liquid or flammable compressed gas shall be clearly and in bold letters marked "Danger-Highly Flammable Liquid" or "Danger-Flammable Compressed Gas". 4. Enclosed Systems for Conveying Highly Flammable Liquids.- (a) Wherever it is reasonably practicable, highly flammable liquids shall be conveyed within a factory in totally enclosed systems consisting of pipe lines, pumps and similar appliances from the storage tank or vessel to the point of use. Such enclosed systems shall be so designed, installed, operated and maintained as to avoid leakage or the risk of spilling. (b) Safety measures in factories where equipment or pipelines containing flammable materials are operated.- Where work of opening any equipment or pipeline containing flammable liquids or gases is to be carried out in any factory, the following provisions shall be complied with, namely:- (i) The system of work permits shall be introduced and unless the equipment or the pipeline is certified to be free of flammable gas or liquid, no person shall be allowed to enter or open the same. (ii) The work of opening such equipment or pipeline shall not be commenced unless the following operations are carried out and checked by the Supervisor in-charge of the Process Department of the Factory:- (1) Blanking Operations -The equipment or pipeline to be opened for repairs or maintenance shall be effectively blanked so as to ensure that no flammable gas or liquid can enter the same under any circumstances during the operation of repairs or maintenance. The Supervisor of the Process Department shall check personally these operations and shall certify accordingly. (2) Flushing operations -The Supervisor of the Process Atomic Energy Factory Rules, 1996 201 Rule 88(Sch.XII) Department shall carry out the steaming or flushing out with water of the equipment or pipeline and shall certify to that effect. (iii) (1) Opening of the equipment -The Supervisor of the Engineering Department of the factory in charge of the work of opening of such equipment or pipeline, or getting clearance from the Supervisor in- charge of the Process Department, shall satisfy himself that the above operations are complete and shall sign the work permits issued by the Supervisor of the Process Department. (2) It shall be the joint responsibility of the Supervisor of the Process Department and the Supervisor of the Engineering Department to check and ensure that the hot lines, if any, in the vicinity of such works are properly screened, in accordance with the safety instructions of the factory management. The work permit shall have a specific entry for this operation which shall be signed by both the Supervisors. (iv) No part of the running equipment or pipeline shall be opened unless a gas test is conducted by a responsible person to ensure that the equipment or pipeline is safe for opening. (v) No workers whose clothes have been contaminated with flammable material shall be allowed to work where any such running equipment or pipeline is being opened. (vi) The Safety Officer or any officer authorised by him, shall have system of random checking on the work permits issued and he shall report any serious deficiencies to the Manager. (vii) All drains of such equipments or pipeline shall be laid into the drains to prevent any splashing of the draining flammable liquids or gases. (viii) Before commencing the opening operation, it shall be ensured that a specific person trained in fire-fighting operations, is kept available and his presence shall be ensured throughout the operation of the opening of the equipment. 5. Preventing Formation of Flammable Mixture with Air.- Wherever there is a possibility for leakage or spill of highly flammable liquid or flammable compressed gas from an equipment, pipe line, valve, joint or other part of a system, all practicable measures shall be taken to contain, drain off or dilute such spills or leakage as to prevent formation of flammable mixture with air. Atomic Energy Factory Rules, 1996 202 Rule 88(Sch.XII) 6. Prevention of Ignition.- (a) In every room, work place or other location where highly flammable liquid or flammable combustible gas is stored, conveyed, handled or used or where there is danger of fire or explosion from accumulation of highly flammable liquid or flammable compressed gas in air, all practicable measures shall be taken to exclude the sources of ignition. Such precautions shall include the following: (i) All electrical apparatus shall either be excluded from the area of risk or they shall be of such construction and so installed and maintained as to prevent the danger of their being a source of ignition; (ii) effective measures shall be adopted for prevention of accumulation of static charges to a dangerous extent; (iii) no person shall wear or be allowed to wear any footwear having iron or steel nails or any other exposed ferrous materials which is likely to cause sparks by friction; (iv) smoking, lighting or carrying of matches, lighters or smoking materials shall be prohibited; (v) transmission belts with iron fasteners shall not be used; and (vi) all other precautions, as are reasonably practicable, shall be taken to prevent initiation of ignition from all other possible sources such as open flames, frictional sparks, overheated surfaces of machinery or plant, chemical or physical-chemical reaction and radiant heat. 7. Prohibition of smoking.- No person shall smoke in any place where highly flammable liquid or flammable compressed gas is present in circumstances that smoking would give rise to a risk of fire. The occupier shall take all practicable measures to ensure compliance with this requirement including display of a bold notice indicating prohibition of smoking at every place where this requirement applies. 8. Fire Fighting.- In every factory where highly flammable liquid or flammable compressed gas is manufactured, stored, handled or used, appropriate and adequate means of fighting a fire shall be provided. The adequacy and suitability of such means which includes the fixed and portable shall appoint a second assessor itself. It shall then fix a date for the hearing of the appeal and shall give due notice of such date to the appellant and to the Competent Authority whose order is appealed against, and shall call upon the two assessors to appear upon such date to assist in the hearing of the appeal. Atomic Energy Factory Rules, 1996 203 Rule 88(Sch.XII-XIV) 9. Exemptions.- If in respect of any factory, the Competent Authority is satisfied that owing to the exceptional circumstances, infrequency of the processes or for any other reason, all or any of the provisions of this schedule is not necessary for protection of the workers in the factory, the Competent Authority may by a certificate in writing, which he may at his discretion revoke at any time, exempt such factory from all or any of such provisions subject to such conditions, if any, as he may specify therein. SCHEDULE XIII RADIOACTIVE SUBSTANCES 1. Handling of radioactive substances.- Rules for handling of Radioactive substances are covered under- a. Radiation Protection Rules, 1971; and b. Atomic Energy (Working of the mines, minerals and handling of prescribed substances) Rules, 1984. 2. These and any other notifications issued from time to time by the Chairman, Atomic Energy Regulatory Board shall be followed. SCHEDULE XIV LASER AND OPTICAL RADIATIONS 1. Application.- The schedule is applicable to Laser radiations and optical radiations from wave lengths between 100 nm and 1 mm i.e. ultraviolet radiation (UVR), visible light, and infrared radiation (IR) pose potential hazards. Sources of optical radiations are catagorised as 1) Sunlight 2) Lamps 3) Lasers and 4) Other incandescent sources. 2. Optical radiations.- The industry, in addition to lasers, makes use of continuous optical radiation sources such as compact arc lamps, quartz-iodide-tungsten lamps, gas and vapour discharge tubes, electric welding units, pulsed optical sources such as flash lamps, exploding wires, and super-radiant light. Goggles and face shields of appropriate characteristics shall be used for protection while working with non laser optical sources. 3. Laser radiations.- Lasers are divided into four classes depending on the power and their effects and the same are given below. (a) Class 1 Lasers- These are the lowest powered lasers such as Gallium Arsenide. They are not considered hazardous. Atomic Energy Factory Rules, 1996 204 Rule 88 (Sch.XIV) (b) Class 2 Lasers- These are low power lasers and pose low risk and safety requirements are as follows. (i) A caution label shall be attached to the equipment. (ii) Workers shall not be allowed to stare into the laser beam for a long time. (iii) The exposure to eye and duration shall not be allowed to exceed permissible levels specified. (c) Class 3 Lasers- These are medium power lasers and pose moderate risk and safety requirements are as follows. (i) The equipments shall have danger label with precautions to be taken marked and written on it. (ii) The laser beam path shall be enclosed and terminations shall be provided at the end of useful paths of direct and any secondary beams. (iii) Shutters, polarisers and optical filters shall be placed at the exit port. (iv) Laser path shall be located in such a way that it shall be always above the eye level of workers. The laser mountings shall be firmly attached to avoid deviations. (v) All unnecessary reflecting surfaces shall be removed from the operating area. (vi) Work permit system shall be evolved and followed for the laser operations. (vii) The warning signs both audio and visual shall be placed at the entrances of the area. (viii) Safety equipment shall be provided and used by the workers. (d) Class 4 Lasers- These are highest powered lasers and hence pose greatest potential for injury or combustion of flammable materials. The safety requirements are as follows. (i) These shall be operated in localised enclosures and wherever complete enclosure is not possible, indoor operations shall be done in a light tight room with interlocked entrances. (ii) The laser firing with remote operations and with video monitoring or other safe viewing techniques shall be Atomic Energy Factory Rules, 1996 205 Rule 88(Sch.XIV-XV) preferred. (iii) Back stops shall wherever feasible be made of diffusively reflecting fire- resistant materials. Safety enclosures shall be used around microwelding and microdrilling work pieces to contain the reflection hazard. (iv) Outdoor high power laser devices such as satellite laser transmission systems and laser radars etc. shall have positive stops on azimuth and elevation traverse to ensure that the beam shall not deviate. (v) All safety precautions associated with high electrical voltage and use of cryogenic liquids shall be followed. (vi) Appropriate safety precautions shall be taken to eliminate the chemical hazards such as release of chemical vapours, vapourisation of target materials etc. Materials used shall be fire resistant. (vii) The work permit system shall be evolved and used for the operation. (viii) Safety equipments such as goggles with proper filters, ear muffs etc. shall be provided and used by the workers. Exposure limits for direct occular exposure from a laser beam will be notified by the Competent Authority. SCHEDULE XV MOTOR VEHICLE GARAGES 1. Application.- This schedule shall apply to all factories where repairs and maintenance of all power driven vehicles such as cars, buses, trucks, tractors, fork lifts etc. is carried on. 2. Location.- The garage shall be located with sufficient space depending on the number of vehicles being handled, with marked aisles for movement of vehicles. There shall be separate and segregated areas for operations such as washing, tyre repairs, welding, battery charging etc. 3. Ventilation, Illumination, Temperature etc. These shall be provided as specified in Rule 11. 4. Tyre repair area.- (a) Trained workers shall only be employed for this work. (b) Mechanical lifting and moving aids shall be provided to workers for lifting of heavy tyres, engine blocks etc. Atomic Energy Factory Rules, 1996 206 Rule 88 (Sch.XV) (c) Free tyres shall be inflated in steel cages or similar devices which shall restrain flying objects if the blowout occurs. (d) Rubber cement and flammable solvents used for patching operations shall be properly stored and this work shall be done in ventilated area. 5. Washing area.- (a) The floor shall be rough trowelled to produce non slip surface. (b) Electrical fixtures used in the area shall be rain or water proof type. (c) Workers shall wear suitable protective gears such as safety shoes, apron etc. 6. Battery Charging area.- (a) The area shall be separated and provided with exhaust ventilation and hydrogen monitors. The electrical fittings shall conform to requirements under relevant standards for explosive atmosphere. (b) Workers shall work in the area with protective equipment such as face shields, gloves, rubber shoes etc. (c) Open flames and smoking shall be banned. (d) Lifting devices and hand trucks shall be used for movement of heavy batteries. (e) First Aid box with acid neutralizing solution and water shall be located near the charging room. (f) Acid carboys shall be handled carefully and siphon shall be used for taking out acid from the carboy for preparation of electrolyte. 7. Paint Shop.- (a) The paint shop shall be located away from welding or battery charging area and proper local exhaust ventilation shall be provided. (b) Personal protective equipments such as respirator, goggles etc. of the approved quality shall be provided to the painters. (c) Smoking shall be banned. 8. General Safety precautions.- (a) Solvents with higher flash points shall be used for cleaning operation and gasoline shall not be used for this operation. Atomic Energy Factory Rules, 1996 207 Rule 88(Sch.XV-XVI) (b) Welding or soldering operation on fuel tanks shall be done only after the tank is empty and is purged out of vapours. A suitable fire extinguisher shall be placed near the workplace. (c) Barricades shall be erected around the vehicle wherever workers are working underneath. They shall wear safety goggles when working underneath. (d) Engines shall not be run in enclosed area unless sufficient exhaust ventilation is available. (e) Traffic lanes inside the garage shall be distinctly marked and traffic rules within the garage shall be framed and rigidly enforced. (f) Housekeeping in the garage shall be given top priority. Cotton rags, wastes etc. shall be stored temporarily in metal drums for disposal later. (g) Appropriate fire fighting equipments shall be located and maintained in the garage. SCHEDULE XVI CRYOGENIC LIQUIDS 1. Application.- These rules are applicable to gases which are in liquid state due to low temperature and having a normal boiling point below -150 degree C. 2. Storage.- (a) These liquids shall be stored only in specially designed suitable containers and which shall be stored at such place where rain or water cannot reach. (b) The containers shall have two pressure relief devices viz. pressure relief valve and frangible rupture disc. (c) Safety devices shall not be tampered with and if they are found triggered, the container shall be checked for loss of vacuum or insulation or leak. (d) The containers shall not be dropped or tipped on their sides. (e) Welding, cutting operations and smoking shall be banned in storage area. (f) The containers shall be marked for its contents. 3. Handling.- (a) Cryogenic liquids shall not be handled in open containers. Atomic Energy Factory Rules, 1996 208 Rule 88(Sch. XVI) (b) The supplier's operating procedures shall be strictly followed. If a plug of ice is formed on the container, the container shall be removed to a remote and safe location and only an authorised worker shall carry out the unplugging work. (c) Workers handling the liquid shall use suitable eye and hand protective appliances. Loose fitting gloves shall be used to facilitate easy removal. (d) Cryogenic liquids shall be transferred wherever possible by using cryogenic pumps. (e) Containers shall be firmly secured and stored in an upright position. (f) Warm, solid or liquid shall not be dropped into cryogenic liquid. (g) While transferring the liquids, the operation shall be done slowly to avoid thermal shock to piping and container. 3. General safety precautions.- (a) Work permit system shall be used for the use of cryogenic liquids. The liquid shall be handled by trained persons by using safety appliances. (b) Operation of transfer of liquid from one container to another shall be done very carefully and slowly. 4. Special precautions.- (a) Handling of liquid oxygen.- (i) All combustible materials such as oils, grease etc. shall be kept away from the area where liquid oxygen is being handled. (ii) Smoking or open flame shall not be permitted in the area. (iii) Liquid oxygen or oxygen rich air shall not be allowed to come in contact with organic salts, oils, grease, asphalt, kerosene, cloth, tar etc. as these react violently with it. (iv) In case of spillage of liquid oxygen on asphalt or any other surface contaminated with oil, no one shall be allowed to walk over it for a minimum period of 30 minutes. (v) Any clothing which is splashed with oxygen shall be changed immediately. (vi) Valves in liquid oxygen system shall be operated slowly as abrupt starting or stopping of the flow may ignite the Atomic Energy Factory Rules, 1996 209 Rule 88 (Sch.XVI-XVII) contaminant. (b) Handling of inert gas system.- The main hazard in such a system is the rupture of container vacuum or pipeline which may lead to increased evaporation and can cause asphyxiation to workers in the area. Hence arrangements shall be made where such systems are installed to vent the gases to areas open to the sky. 5. First Aid.- A properly trained person shall always be made available wherever cryogenic liquids are handled, stored or used. First aid box with specified medicines shall be provided and which shall be regularly checked for availability of medicines. SCHEDULE XVII USE OF ALKALI METALS 1. Application.- This schedule shall be applicable towards storage, handling and disposal of alkali metals such as Potassium and Sodium. 2. Storage.- (a) Storage area for large quantities shall be separated from main building and located at a safe distance to avoid risk of explosion. An explosion venting shall be provided to the building. (b) The building construction shall be such that rain water shall not leak in the area and raised platforms for storing of containers shall be constructed to prevent ground water reaching the containers under any circumstances. (c) Water in any form shall not come in the storage area. Water and steam pipes shall not pass through the area. (d) Smoking shall be prohibited and a warning prohibiting use of water shall be prominently displayed. Appropriate fire extinguishers shall be provided and no other type of extinguisher shall be kept anywhere near the building. (e) All electrical fittings and wiring in the area shall be of explosion proof type and shall conform to relevant BIS standards. (f) Notice indicating dangers involved and safety measures to be taken shall be displayed on the containers. Containers storing the metals shall be checked periodically for corrosion or damage and shall be replaced immediately if found defective. (g) The empty containers shall be separately stored in the same area till they are disposed off. Atomic Energy Factory Rules, 1996 210 Rules 88 (Sch.XVII)-89 3. Handling.- (a) Dispensing area shall be separated form bulk storage area. However the safety provisions shall be same as those of bulk storage area. (b) The equipment and systems used for handling the metals shall be properly designed for safe operation. Steam shall not be used for directly heating and liquefying the metals. (c) Transfer of molten alkali metals shall be done under an inert gas or vacuum and at lowest possible temperature and pressure. (d) A fast acting drainage system shall be incorporated in a liquid metal handling system to allow the liquid to drain in secondary containment system. (e) All piping shall be seamless and welded construction shall be employed throughout, except at valves and connections to equipment. Machinery and piping shall be effectively grounded wherever possibility of accumulation of static charge exists. (f) Non sparking tools shall, only be used for opening of bulk storage drums etc. (g) Suitable personal protective equipment like goggles or face shields, aprons, gloves etc. shall be provided and worn by the workers. (h) Safe handling procedures shall be laid down and work permit system shall be evolved and followed for all operations on alkali metals. 4. Waste disposal.- Sodium wastes shall be disposed off by burning it in a well ventilated area and workers present shall wear suitable protective equipments such as respirators, gloves etc. for protection from fumes.

Previous and next

All provisions of Atomic Energy (Factories) Rules, 1996

Questions people ask

Is rule 88 of Atomic Energy (Factories) Rules, 1996 still in force?

No repeal of Atomic Energy (Factories) Rules, 1996 is recorded.