Rule 115, THE CENTRAL MOTOR VEHICLES RULES, 1989, (1-164): Emission of smoke, vapour, etc. from motor vehicles
THE CENTRAL MOTOR VEHICLES RULES, 1989, (1-164) - Rule 115
Text of rule 115
Emission of smoke, vapour, etc. from motor vehicles
115. Emission of smoke, vapour, etc. from motor vehicles.— 258[(1) Every motor
vehicle other than motor cycles of engine capacity not exceeding 70 cc, manufactured
prior to the first day of March 1990, shall be maintained in such condition and shall be so
driven so as to comply with the standards prescribed in these rules.]
259[(2) On and after 1st October, 2004, every motor vehicle operating on—
(i) Petrol/CNG/LPG shall comply with the idling emission standards for Carbon monoxide
(CO) and Hydrocarbon (HC) given in the Table below:—
255
Substituted by G.S.R. 111(E), dated 10-2-2004, for "Provided further that in the case of
tractors, vertical" (w.e.f. 10-8-2004).
256
Inserted by G.S.R. 642(E), dated 28-7-2000 (w.e.f. 28-7-2000).
257
Substituted by G.S.R. 116(E), dated 27-2-2002, for "no exhaust pipe" (w.e.f. 27-8-2002).
258
Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
259
Sub-R. (2) substituted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004) and as corrected
by vide G.S.R. 176(E), dated 5-3-2004
97
TABLE
PETROL/CNG/LPG DRIVEN VEHICLES
SI. No. Vehicle Type Co % *HC(n-hexane
equivalent) ppm
1. 2 and 3-Wheelers (2/4-stroke) (Vehicles
manufactured on and before 31st
March, 2000)
4.5 9000
2. 2 and 3-Wheelers (2-stroke) (Vehicles
manufactured after 31st March, 2000)
3.5 6000
3. 2 and 3-Wheelers (4-stroke) (Vehicles
manufactured after 31st March, 2000)
3.5 4500
4. Bharat Stage II compliant 4-wheelers 0.5 750
5. 4-Wheelers other than Bharat Stage II
compliant
3.0 1500
Note.—The test shall be carried out using the instrument type approved as per rule
116(3) of the Central Motor Vehicles Rules, 1989 (CMVR) with the vehicle engine
wanned up after a run of minimum 15 minutes on a variable course under normal traffic
condition. During the test the vehicle engine shall be running at idling speed and the
sampling probe shall be inserted into the vehicle exhaust system to a depth not less than
300mm. In case CO and/or HC emission values recorded during the test are not within
the limits, the testing shall be discontinued and the vehicle owner shall be advised to
resubmit the vehicle after repair/service.
The idling emission standards for vehicles when operating on Compressed
Natural Gas (CNG), shall contain Non-Methane Hydrocarbon (NMHC) in place of
Hydrocarbon (HC) and shall be estimated by the following formula: NMHO0.3xHC
Where HC= Total Hydrocarbon measured as n-hexane equivalent. Similarly idling
emission standards for vehicles when operating on Liquefied Petroleum Gas (LPG) shall
contain Reactive Hydroharbon (RHC) in place of Hydrocarbon (HC) and shall be
estimated by the following formula:
RHC=0.5 x HC
Where HC= Total Hydrocarbon measured as n-hexane equivalent:
Provided that in case of Petrol vehicles fitted with three-way closed loop catalytic
converters operating in a specific city or area, the Government of the respective State or
Union Territory Administration, as the case may be, may, by notification in the Official
Gazette, specify the introduction of measurement of LAMBDA (dimensionless value
98
representing burning efficiency of an engine in terms of the air/fuel ratio in the exhaust
gases) and tighter emission norms for in-use vehicles with such periodicity as may be
warranted, after ensuring that gas analyzers capable of measuring the values, duly
approved by the testing agencies, are available in such city or area, as the case may be:
Provided further that testing procedures are prescribed in TAP documents Nos. 115 and
116 as amended from time to time:
Provided also that the compliance to the limits prescribed in the above proviso shall be
included in the certificate issued by the vehicle manufacturer in Form 22 or Form 22-A,
as applicable for the vehicle manufactured on or after 1st October, 2004.
(ii) Smoke density for all diesel-driven vehicles shall be as follows:—
TABLE
DIESEL VEHICLES
Method of Test Maximum Smoke Density
Light absorption coefficient
(1/m)
Mar tidge units
Free acceleration test for turbo
charged engine and naturally
aspirated engine
2.45 65
The free acceleration test shall be carried out using the instrument type approved as per
CMVR 116(3) with the vehicle engine wanned up to attain oil temperature of minimum
60°C. During each free acceleration, maximum no load speed reached shall be within
bandwidth of ±500 rpm of the average value in respect of 3-wheeler vehicles and ±300
rpm of the average value for all other categories of vehicles. The free acceleration test
shall be repeated till the peak smoke density values recorded in four successive
accelerations meeting the above maximum no load rpm criteria are situated within a
bandwidth of 25% of the arithmetic mean (in m-1 unit) of these values or within a
bandwidth 0.25 K, whichever is higher and do not form a decreasing sequence. The
smoke density to be recorded shall be arithmetic mean of these four readings. In case
the valid readings are not obtained within 10 free accelerations or the smoke . density
recorded is not within the limits, the testing shall be discontinued and the vehicle owner
shall be advised to resubmit the vehicle after repair/ service.]
(3) On and from the date260 of commencement of this sub-rule, all petrol-driven vehicles
shall be so manufactured that they comply with the mass emission standards as
specified at Annexure I. The breakdown of the operating cycle used for the test shall be
260 Brought into force on 1st day of April, 1991 vide S.O.869(E), dated 27-10-1989.
99
as specified at Annexure II, and the reference fuel for all such tests shall be specified in
Annexure III to these rules.
(4) On and from the date261 of commencement of this sub-rule, all diesel-driven vehicles
shall be so manufactured that they comply with the standards based on exhaust gas
opacity as specified at Annexure IV to these rules.
(5) On and from the date262 of commencement of this sub-rule, all petrol-driven vehicles
shall be so manufactured that they comply with the following levels of emissions
263[when tested as per test cycle specified in Annexure V]:—
Mass of Carbon Monoxide Mass of Hydrocarbons (CO)
(HQ
Mass of Nitrogen Oxides
(NO)
Maximum grams per KW1T Maximum grams per KWH Maximum grams per KWH
14 3.5 18
264[Provided the standards for exhaust gas emissions applicable to agricultural tractors
shall be notified separately.]
(6) Each motor vehicle manufactured on and after the dates specified in sub-rule (2), (3),
(4) or (5), shall be certified by the manufacturers to be conforming to the standards
specified in the said sub-sections, and further certify that the components liable to effect
the emission of gaseous pollutants are so designed, constructed and assembled as to
enable the vehicle, in normal use, despite the vibration to which it may be subjected, to
comply with the provisions of the said sub-rule.
265[(7) After the expiry of a period of one year from the date on which the motor vehicle
was first registered, every such vehicle shall carry a valid "Pollution under control"
certificate issued by an agency authorised for this purpose by the State Government.
The validity of the certificate shall be for 266[six months] and the certificate shall always
be carried in the vehicle and produced on demand by the officers referred to in sub-rule
(1) of rule 116.
(8) The certificate issued under sub-rule (7) shall, while it remains effective, be valid
throughout India.]
261
Brought into force on 1st day of April, 1991 vide S.O.869(E), dated 27-10-1989.
262
Brought into force on 1st day of April, 1992 videS.0.869(E), dated 27-10-1989.
263
Substituted by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
264
Inserted by G.S.R 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
265
Added by G.S.R. 338(E), dated 26-3-1993 (w.e.f. 26-3-1993).
266
Substituted by G.S.R 111(E), dated 10-2-2004, for "six months or any lesser period as may be
specified by die State Government from time to time" (w.e.f. 10-8-2004).
100
267[(9) Mass emission standard for diesel vehicles
Type approval tests
Vehicle Category HC*
(g/KWH)
CO*
(g/KWH)
NOx
(g/KWH)
Smoke
Medium & Heavy over
3.5 Ton/GVW
Light diesel upto
3.5 Ton/GVW
or
2.4
2.4
11.2
11.2
14.4
14.4
***
***
Reference mass R(Kg) CO** g/KM HC+NOx g/KM ***
R<1020
1020<R<1250
1250<R< 1470
1470<R< 1700
1700<R<1930
1930<R<2150
R<2150
5.0
5.7
6.4
7.0
7.7
8.2
9.0
2.0
2.2
2.5
2.7
2.9
3.5
4.0
Note:
*The test cycle is as per 13 mode cycle on dynamometer.
** The test should be as per Indian driving cycle with cold start.
***The emissions of visible pollutants (smoke) shall not exceed the limit value to smoke
density. When expressed as light absorption coefficient given below for various nominal
flows when tested as constant speeds over full load. (As indicated at Annexure I).
COP STANDARDS
*10% relaxation in the standards for HC, CO and NOx would be given. **10% relaxation
in the standards for CO and combined HC+NOx would be given.
268[Mass emission standard for petrol-driven vehicles—Effective from 1st April, 1998
(i) Passenger Cars—
Type approval tests
Cubic Capacity
(cm3)
Carbon
Monoxide (gm/km)
HC+NOx
(gm/km)
Passenger cars
fitted with
catalytic
converter
Passenger cars
not fitted with
catalytic
converter
Passenger
cars fitted
With catalytic
converter
Passenger
cars not fitted
with catalytic
converter
<1400 4.34 8.68 1.50 3.00
>1400<2000 5.60 11.20 1.92 3.84
>2000 6.20 12.40 2.18 4.36
267
Substituted by G.S.R. 163(E), dated 29-3-1996 (w.e.f. 1-4-1996). Earlier sub-R. (9) was added
by G.S.R. 609(E), dated 15-9-1993 (w.e.f. 15-9-1993).
268
Substituted by G.S.R. 46(E), dated 21-1-1998 (w.e.f. 1-4-1998).
101
Notes.—1. The tests will be as per Indian driving cycle with warm start. However, with
effect from 1st April, 1998, the test will be as per Indian driving cycle with cold start for
catalytic converter fitted vehicles as:—
Soak Temperature = 20°-30°C
Soak Period = 6.30 hrs
Preparatory running before sampling = 4 cycles
Number of test cycles = 6
Break down of cycles = Indian driving cycle as per Annexure II
2. For passenger cars not fitted with catalytic converters, the test will continue to be with
warm start as per existing procedure, till 1-4-2000.
3. There should be no crankcase emission.
4. Evaporative emission should not be more than 2.0g/test.
5. COP standards: 20% relaxation in the standards for Carbon Monoxide and combined
ITC + NOx would be given.
6. For vehicles fitted with catalytic converter a deterioration factor of 1.2 on Type-
Approval Limits will be applicable for durability.]
(ii) Three-Wheelers (for all categories)—
CO
HC + NOx
gms/km
gms/km
6.75
5.40
Note:
1. The test will be as per Indian driving cycle with warm start. However, with effect from
1st April, 1998, the test will be as per Indian driving cycle with cold start.
2. COP standards: 20% relaxation in the standards for Carbon Monoxide and combined
HC + NOx would be given.
(iii) Two-Wheelers (for all categories)—
CO
HC + NOx
gms/Km
gms/Km
4.50
3.60
Note:
1. The test will be as per Indian driving cycle with warm start. However, with effect from
1st April, 1998, the test will be as per Indian driving cycle with cold start.
2. COP standards: 20% relaxation in the standards for Carbon Monoxide and combined
HC+NOx would be given.
102
ANNEXURE I
Nominal Flow Light Absorption Nominal Flow Light Absorption
G(l/2) (K(l/m)) G(l/2) (K(l/m))
42 2.26 120 1.37
45 2.19 125 1.345
50 2.08 130 1.32
55 1.985 135 1.30
60 1.90 140 1.27
65 1.84 145 1.25
70 1.775 150 1.205
75 1.72 160 1.19
80 1.665 165 1.17
85 1.62 170 1.155
90 1.575 175 1.14
95 1.535 180 1.125
100 1.495 185 1.11
105 1.465 190 1 095
110 1.425 195 1.08
115 1.395 200 1.065]
269[270[(10) Mass Emission Standards for vehicles manufactured on and after 1st June,
1999 in case of National Capital Region of Delhi and in other cases on and after 1st
April, 2000]
A. For Petrol-Driven Vehicles
(1) Passenger Cars CO(g/km) HC+NOx(g/km)
Type Approval 2.72 0.97
Conformity of Production 3.16 1,13
Notes.—The test shall be as per the modified Indian driving cycle, with cold start, as
specified in Annexure IV-B, on Chassis Dynamometer.
There should be no crankcase emission.
Evaporative emission should not be more than 2.0g/test.
For vehicles fitted with catalytic converter, a deterioration factor of 1.2 on Type Approval
Limits will be applicable for durability.
Commercial fuel shall be as notified by the Ministry of Environment and Forests vide
Notification No. G.S.R. 176(E), dated the 2nd April, 1996.
Reference test fuel shall be as specified in Annexure IV-C.
CO(g/km) HC+NOx(g/km) 2-Wheelers and 3-Wheelers
2-Wheeler 3-Wheeler 2-Wheeler 3-Wheeler
Type Approval 2.0 4.0 2.0 2.0
Conformity of Production 2.4 4.8 2.4 2.4
269
Sub-R (10) inserted by G.S.R. 493(E), dated 28-8-1997 (w.e.f. 1-4-2000).
270
Substituted by G.S.R. 399(E), dated 1-6-1999, for "10. Mass Emission Standards for vehicles
manufactured on and after 1st April, 2000" (w.e.f. 1-6-1999).
103
Notes.—The test shall be as per the Indian driving cycle, with cold start, on Chassis
Dynamometer as specified in Annexure IV-B to the principal rules.
Commercial fuel shall be as notified by the Ministry of Environment and Forests vide
Notification No. G.S.R. 176(E), dated the 2nd April, 1996.
Reference test fuel shall be as specified in Annexure FV-C.
271[For 2-wheelers and 3-wheelers fitted with catalytic converter, a deterioration factor of
1.2 on Type Approval Limits, will be applicable for durability:
Provided that the vehicle manufacturers may opt for an ageing test of 30,000 kms for
evaluating deterioration factor, as per procedure that may be laid down by the Central
Government.]
B. For Diesel Vehicles (Including Two and Three-Wheelers)
I. Vehicles with GVW exceeding 3.5 ton
Limits for Pollutants
Type Approval Conformity of Production
CCX g/KWn 4.5 4.9
HCfe/kWh 1.1 1.23
NOxfe/kWh 8.0 9.0
FM(g/k Wh) for engines with power exceeding
85kW
0.36 0.4
PM(g/k Wh) or engines with power not exceeding
85k W
0.36
0.4
II. Vehicles with G VW equal to or less than 3.5 ton
Limits for Pollutants
Type Approval Conformity of Production
CO( g/kWh) 4.5 4.9
HC(g/kWh) 1,1 1.23
NOx (g/kWh) 8.0 9.0
PM(g/k Wh) for engines with power exceed ing
85kW
0.36 0.4
PM(g/ k Wh) for engines with power equal to or
less than 85kW
0.61 0.68
Or Chassis Dynamometer Test
Reference Mass (kg) Limits for Type Approval
gm/km
Limits for conformity of
Production gm/km
CO HC+NOx PM CO HC+NOx PM
R<1250
1250<R<1700
1700<R
2.72
5.17
6.90
0.97
1.40
1.70
0.14
0.19
0.25
3.16
6.0
8.0
1.13
1.60
2.0
0.18
0.22
0.29
Notes.—The test for vehicles with GVW equal to or less than 3.5 ton shall be as per the
13 mode cycle on engine dynamometer specified in Annexure IV-A to the principal rules.
271 Inserted by G.S.R. 400(E), dated 31-5-2002 (w.e.f. 31-5-2002).
104
The test shall be as per the Indian driving cycle, for 2-Wheelers and 3-Wheelers and
modified Indian driving cycle for 4-Wheelers with cold start, as specified in Annexure IV-
B on Chassis Dynamometer.
For vehicles fitted with catalytic converters a deterioration factor 1.1 of CO; 1.0 for
HC+NOx and 1.2 for PM on type approval limits will be applicable for durability.
The emission of visible pollutants (smoke) shall not exceed the limit value to smoke
density, when expressed as light absorption co-efficient for various nominal flows as in
Annexure I to rule 115(9), (Notification No. G.S.R. 163(E), dated 29th March, 1996),
when tested at constant speeds over full load. These smoke limits are without correction
factor and engines are to be tested with conditioned air supplied to the engine to
maintain atmospheric factor of 0.98 to 1.02.
Commercial fuel shall be as notified by the Ministry of Environment and Forests vide
Notification No. G.S.R. 176(E), dated the 2nd April, 1996.
Reference test fuel shall be as specified in Annexure IV-D.]
272For 2-wheelers and 3-wheelers fitted with catalytic converter, the deterioration factor
shall be as follows:
CO* 1.1; HC + NOx = 1.0; PM-1.2:
Provided that the vehicle manufacturers may opt for an ageing test of 30,000 kms lor
evaluating deterioration factor, as per procedure that may be laid down by the Central
Government:
Provided further that the above provisions shall come into force after six months from the
publication of the notification.]
273[(11) Mass Emission Standards (Bharat Stage II):—
(A) Motor Cars with seating capacity of and up to 6 persons (including driver) and Gross
Vehicle Mass (GVM) not exceeding 2500 kg.
Standards (Type Approval=COP)(g/km)
Vehicles with CO (HC+NOx) PM
Gasoline engine 2.2 0.5 —
Diesel engine 1.0 0.7 0.08
B) Four-Wheeler Passenger Vehicles with GVW equal to or less than 3500 kg and
designed to carry more than 6 persons (including driver) or maximum mass of which
exceeds 2500 kg.
272
Inserted by G.S.R. 400(E), dated 31-5-2002 (w.e. f. 31 -5-2002).
273
Inserted by G.S.R. 77(E), dated 31-1-2000. Brought into force in the National Capital Region
w.e.f. 1-4-2000 vide G.S.R. 77(E), dated 31-1-2000, in Mumbai (including Greater Mumbai) w.e.f.
1-1-2001 and in Calcutta and Chennai w.e.f. 1-7-2001 vide G.S.R. 779(E), dated 29-8-2000.
105
Limit Values for Type Approval (TA) as well as COP
Mass of C 0(g/km) Mass of HC+NOx(g/km) Mass of PM(g/km)
Class Ref. Mass(rw) kg
Case line Diesel Gasoline Diesel Diesel
I rw<1250 2.2 1.0 0.5 0.7 0.08
II l25U<rw<1700 4.0 1.25 0.6 1.0 0.12
III I700<rw 5.0 1.5 0.7 1.2 0.17
Notes:—
1. The test including driving cycle shall be as per sub-rule (10), with the modifications
that:—
(i) there shall be no relaxation of norms for COP purposes,
(ii) the tests shall be on Chassis dynamometer,
(iii) the driving cycle shall be at a maximum speed of 90 kmph, and
(iv) the reference fuel shall be of a maximum of 0.05% sulphur content.
2. Commercial fuel for meeting above norms shall be upto 0.05% mass maximum
sulphur content.
3. There shall be no crankcase emissions for petrol-driven vehicles.
4. Evaporative emission shall not be more than 2.0g/ test from petrol-driven vehicles.
5. For the above vehicles when fitted with catalytic converter deterioration factor shall be
as follows:—.
Gasoline engines: CO=1.2; (HC+NOx)=l .2;
Diesel engines: CO=l.l; (HC+NOx)=1.0; PM=1.2:
Provided that the vehicle manufacturers may opt for an ageing test of 80,000 kms for
evaluating deterioration factor, as per procedure that may be laid down by the Central
Government.
6. For diesel engine vehicles, the emission of visible pollutants (smoke) shall not exceed
the limit value to smoke density, when expressed as light absorption coefficient for
various nominal flows as in Annexure I to rule 115(9) when tested at constant speeds
over full load.]
274[(C) Four-Wheeled Vehicles (other than passenger vehicles) with GVW equal to or
less than 3500 kg shall conform the following norms:—
274 Inserted by G.S.R. 286(E), dated 24-4-2001 published in the Gazette of India, dated
24-4-2001, Ext., Pt. II, S. 3(z), SI. No. 198. In the National Capital Territory of Delhi in
respect of Vehicles manufactured on or after six months from the date of publication in
106
Engine Dynamometer Test
Limit Values for Type Approval (TA) as well as (COP)
CO(g/kWh) HC (g/kWh) NOx (g/kWh) PM (g/kWh)
4.0 1.1 7.0 0.15
Or Chassis Dynamometer Test
Class Ref. Mass (RM) Kg Mass of CO (g/km) Mass of HC+NQx (g/km) Mass of
PM(g/km)
RM Gasoline Diesel Gasoline Diesel
I RM < 1250 2.2 1.0 0.5 0.7 0.08
II 1250 <RM< 1700 4.0 1.25 0.6 1.0 0.12
III 1700 < RM 5.0 1.5 0.7 1.2 0.17
Notes:
1. (a) There shall be no relaxation for COP purposes.
(b) The tests shall be carried out on the engine dynamometer operation as specified in
Annexure IV-A of the rules. The tests on Chassis dynamometer shall be as per the
driving cycle given in Note of clause (B) of sub-rule (11) of rule 115.
(c) The reference fuel shall be of a maximum of 0.05% mass sulphur content.
2. Commercial fuel for meeting above norms shall be up to 0.05% maximum mass
sulphur content.
3. For diesel engine vehicles the emission of visible pollutants (smoke) shall not exceed
the limit value to smoke density, when expressed as light absorption coefficient for
various nominal flows as in Annexure I to sub-rule (9) of rule 115 when tested at
constant speeds over full load. These smoke limits are without correction factor and
engines are to be tested with conditioned air supplied to the engine to maintain
atmospheric factor of 0.98 to 1.02.
4. For diesel engined vehicles, the free acceleration smoke for naturally aspirated and
turbo-charged engines shall not exceed the smoke density limit value as in clause (c) of
sub-rule (2) of rule 115.
the Official Gazette, i.e., 24-4-2001 and in respect of the "Four-Wheeled Transport
Vehicles" which are plying on Inter-State Permits or on National Permits or on All India
Tourist Permits within the jurisdiction of National Capital Territory of Delhi, and in respect
of any Vehicles in other areas of country, from such date as the Central Government
may, by notification appoint in the Official Gazette, and different dates may be appointed
for different areas.
107
5. There shall be no crankcase emissions for petrol engined vehicles.
6. Evaporative emission shall not be more than 2.0g/test from petrol engined vehicles.
(D) Vehicles with GVW exceeding 3500kg shall conform the following norms:—
Limit Values for Type Approval (TA) as well as (COP)
CO(g/kWh) HC(g/kWh) NOx(g/kWh) PM(g/kWh)
4.0 1.1 7.0 0.15
Notes:
1. (a) There shall be no relaxation for COP purposes.
(b) The tests shall be carried out on the engine dynamometer operation as specified in
Annexure IV-A of the rules.
(c) The reference fuel shall be of a maximum of 0.05% mass sulphur content.
2. Commercial fuel for meeting above norms shall be up to 0.05% mass maximum
sulphur content.
3. For diesel engined vehicles, the emission of visible pollutants (smoke) shall not
exceed the limit value to smoke density, when expressed as light absorption coefficient
for various nominal flow as in Annexure I to sub-rule (9) of rule 115 when tested at
constant speeds over full load. These smoke limits are without correction factor and
engines are to be tested with conditioned air supplied to the engine to maintain
atmospheric factor of 0.98 to 1.02.
4. For diesel engined vehicles, the free acceleration smoke for naturally aspirated and
turbo-charged engines shall not exceed the smoke density limit value as in clause (c) of
sub-rule (2) of rule 115.]
275[(12) Mass emission standards (Bharat Stage II) for two-wheeler and three-wheeler
manufactured on and from 1st April, 2005 shall be as follows, namely:—
TABLE
Vehicle Category Pollutants TA=COP norms g/km TA = COP D.F. (*)
(1) (2) (3) (4)
CO 1.50 1.2 Two-wheeler (Petrol)
HC+NOx 1.50 1.2
CO 2.25 1.2 Three-wheeler (Petrol)
HC+NOx 2.00 1.2
CO 1.00 1.1
HC+NOx 0.85 1.0
Two-wheeler and three-
wheeler (Diesel)
PM 0.10 1.2
Deterioration Factor, see para (c) below.
275 Inserted by G.S.R. 720(E), dated 10-9-2003.
108
(a) The test shall be as per the Indian Driving Cycle with cold start on chassis
dynamometer as specified in the Table given below by testing agencies, namely:—
TABLE
Test Cell Conditions Petrol two-wheeler and three-
wheeler
Diesel two-wheeler ajid three-
wheeler
(1) (2) (3)
Soak Temperature 20-30° C 20-30° C
Soak period 6-30 hours 6-30 hours
Preparatory running before
sampling
Idling of 40 seconds and 4 cycles Idling of 40 seconds
No. of test cycles 6 6
Breakdown of cycles Indian Driving Cycle as per
Annexure II to principal rule
Indian Driving Cycle as per
Annexure II to principal rule
(b) Reference fuel for testing shall be in line with that in the ECE;
(c)(i) For all types of two-wheeler and three-wheeler petrol vehicles, a deterioration
factor as specified in column (4) in the Table in this sub-rule shall be applicable for
durability:
Provided that the vehicle manufacturer may opt for an ageing test of 30,000 kms for
evaluating deterioration factor, as per procedure that may be laid down by the Central
Government from time to time;
(ii) For all types of two-wheeler and three-wheeler diesel vehicles, a deterioration factor
as specified in column (4) in the Table in this sub-rule shall be applicable for durability:
Provided that the vehicle manufacturer may opt for an ageing test of 30,000 kms for
evaluating deterioration factor, as per procedure that may be laid down by the Central
Government from time to time;
(d) For diesel engine vehicles, the emission of visible pollutants (smoke) shall not
exceed the limit value to smoke density, when expressed as light absorption co-efficient
for various nominal flow as indicated in Annexure I to sub-rule (9) of rule 115 when
tested at constant speed over full load;
(e) COP frequency and samples:—
Annual Production SI.
No.
Type of Vehicle
Exceeding Upto
COP Frequency
(1) (2) (3) (4) (5)
1. Two-wheeler and three-
wheeler
250 per 6 months 10000 per year Once every year
2. Two-wheeler 100000 per year 150000 per 6 months Once every 6 months
3. Two-wheeler 150000 per 6 months _ Once every 3 months
4. Three-wheeler 10000 per year 75000 per 6 months Once every 6 months
5. Three-wheeler 75000 per 6 months — Once every 3 months
109
For production volumes of less than 250 per 6 months the method as prescribed in the
proviso to rule 126-A shall apply;
(f) Testing procedures shall be in accordance with the reference document
MOST/CMVR/TAP-115/116 as amended from time to time by the Government of India in
the Ministry of Road Transport and Highways:]
276[Provided that Mass Emission Standards (Bharat Stage II) for diesel driven two-
wheeler and three-wheeler shall come into force on the dates specified against each of
the States in Table below:—
TABLE
SI. No. State Date
(1) (2) (3)
1. Rajasthan 1st June, 2005
2. Uttar Pradesh—
Mathura, Kannauj, Muzaffarnagar, Aligarh,
Farukkabad, Saharanpur, Badaun, Barreily,
Moradabad, Hathras, Rampur, Bijnor, Agra, Pilibhit,
J.P. Nagar, Mainpuri, Lalitpur, Hardoi, Firozabad,
Jhansi, Shahjahanpur, Eta wall, Jalon, Lakhirnpur
Kheri, Etah, Mahoba and Sitapur
1 st June, 2005
3. Uttaranchal 1st July, 2005
4. Madhya Pradesh 1st September, 2005
5. Himachal Pradesh 1st October, 2005
6. Jammu and Kashmir 1st October, 2005
7. Punjab 1st October, 2005.]
277[(14) Mass Emission Standards (Bharat Stage III).—The Mass Emission Standards for
Bharat Stage III shall be as under:—
(A) Motor cars with seating capacity of and up to six persons (including driver) and
Gross Vehicle Weight not exceeding 2500 kg.
Limit Values for Type Approval (TA) as well as COP (g/km) Vehicles with
CO HC NOx HC+NOx PM
Gasoline 2.30 0.20 0.15 - -
Diesel engine 0.64 - 0.50 0.56 0.05
276 Inserted by G.S.R. 200(E),dated 1-4-2005(w.e.f. 1-4-2005).
277 Inserted by G.S.R. 686(E), dated 20-10-2004. Brought into force—(a) in the National Capital
Region and the cities of Mumbai, Kolkata, Chennai, Bangalore, Hyderabad including
Secundrabad, Ahmedabad, Pune, Surat, Kanpur and Agra in respect of four-wheeled vehicles
manufactured on and from 1st April 2005, except in respect of four-wheeled transport vehicles
plying on Inter-State Permits or National Permits or All India Tourist Permits within the jurisdiction
of these cities; and (b) in other areas of the country, from such date as may be notified by the
Central Government. Here "National Capital Region" shall have the same meaning as assigned
to it in clause (/) of section 2 of the National Capital Region Planning Board Act, 1985 (2 of 1985).
110
(B) Four-Wheeler Passenger Vehicles with Gross Vehicle Weight equal to or less than
3500 kg and designed to carry more than six persons (including driver) or 3000 kg.
and
(C) Four-wheeled Vehicle (other than passenger vehicles) with Gross Vehicle Weight
equal to or less than 3500 kg shall conform to the following norms:—
Limit Values for Type Approval (TA) (g/km) as well as COP
CO HC NOx HC+NOx PM
Class Ref. Mass
(rw) kg
Gasoline Diesel Gasoline Diesel Gasoline Diesel Gasoline Diesel Diesel
I rw<1305 2.30 0.64 0.20 — 0.15 0.50 — 0.56 0.05
II 1305<rw
<1760
4.17 0.80 0.25 — 0.18 0.65 — 0.72 0.07
III 1760<rw 5.22 0.95 0.29 — 0.21 0.78 — 0.86 0.10
13 In case of diesel vehicles, the engine power shall be measured on engine
dynamometer and the measured power shall not differ from the specified power as given
below:
(i)For Type approval: ± 5% at maximum power point and ± 10% at other measurement
points for single cylinder engines. ± 2% at maximum power point and + 6 „ and -2% at
other measurement points for all other engines.
(ii) Testing procedures shall be in accordance with Chapter 6 of Part IV of the reference
document MOST/CMVR/TAP-115/116 as amended trom time to time by the Government
of India in the Ministry of Shipping, Road Transport and Highways.
14. The vehicles described in clauses (A), (B) and (C) of this sub-rule should comply
with rule 115(2).
(D) Diesel vehicles with GVW exceeding 3500 kg shall conform to the following norms:—
Deterioration factors Engine category
CO HC NOx HC+NOx PM
Gasoline/Gas Engine 1.2 1.2 1.2 - -
Diesel Engine 1.1 — 1.0 1.0 1.2
11. In case of diesel vehicles, the engine power shall be measured on engine
dynamometer and the measured power shall not differ from the specified power as given
below:
(i) For Type approval: ±2% at maximum power point and +6% and -2% at other
measurement points.
(ii) For conformity of production: -5%/+8% at maximum power point.
111
(iii) Testing procedures shall be in accordance with Chapter 6 of Part TV of the reference
document MOST/CMVR/TAP-115/116 as amended from time to time by the Government
of India in the Ministry of Shipping, Road Transport and Highways.
12. The vehicles mentioned in clause (D) shall also comply with rule 115(2).
(E) Diesel vehicles with GVW exceeding 3500 kg. and fitted with advanced exhaust after
treatment system including De-NOx catalyst and/or particulate trap shall additionally
conform to the following norms:—
Limit Values for Type Approval (TA) as well as (COP)
Engine Transient Cycle (ETC)
CO(g/kWh) HC (g/kWh) NOx (g/kWh) PM (g/kWh)
5.45 0.78 5.0 0.16/0.21'3'
(1) For engines having swept volume of less than 0.75 litre per cylinder and a rated
power speed of more than 3000 rpm.
(2) For diesel engines only. Notes.—
1. The test shall be on engine dynamometer.
2. There shall be no relaxation of norms for COP purposes.
3. The gaseous and particulate emissions are to be determined on the ESC lest as
described in EEC document 1999/96/EC.
4. The smoke opacity is to be determined on the ELR test as described in EEC
document 1999/96/EC.
5. In case of vehicles operating on CNG or LPG mode all the provisions prescribed in
rules 115-B and 115-C shall be respectively applicable, except that limiting value shall
be as per clause (D) above.
6. The reference fuel shall be as specified in Annexure IV-F, Annexure 1V-II and
Annexure rV-I for diesel, LPG and CNG, respectively.
7. The Conformity of Production (COP) testing procedure shall be as described in
section 9 of Annexure I of EEC Directive 88/77/EEC last amended by 1999/96/EC.
8. The COP frequency and samples:—
(/) The COP period for each engine model including its variants shall be once in a year.
(ii) For production volume of less than 250 for six months, the method as prescribed in
the provisos to rule 126-A shall apply.
9. For diesel engine vehicles, the emission of visible pollutants (smoke) shall not exceed
the limit value of smoke density, as per Annexure I to rule 115(9). These smoke limits
112
are without correction factor and engines are to be tested with conditioned air supplied to
the engine to maintain atmospheric factor of 0.98 to 1.02.
10. The vehicles meeting the above norms shall use commercial fuel as per BIS
specification IS:1460-2000 (Amendment No. I—January, 2003) (Fourth Revision) for
Diesel and IS:2796-2000 (Amendment No. II—February, 2003) (Third Revision) for
Gasoline.
11. In case of diesel vehicles, the engine power shall be measured on engine
dynamometer and the measured power shall meet the requirements as given below:
(i) For Type approval: ± 2% at maximum power point and +6% and -2% at other
measurement points.
(ii) For conformity of production: -5%/+8% at maximum power point.
(iii) Testing procedures shall be in accordance with Chapter 6 of Part IV of the reference
document MOST/CMVR/TAP-115/116 as amended from time to time by the Government
of India in the Ministry of Shipping, Road Transport and Highways.
12. The vehicles mentioned in clause (E) shall also comply with rule 115(2).]
278[115-A. "[Emission of smoke and vapour from agricultural tractors, power tillers
and construction equipment vehicles driven by diesel engines.—(1) Every
^[agricultural tractor and construction equipment vehicle] manufactured on and from the
date of commencement of this rule shall be maintained by its owner in such condition
and shall be so used that visible and gaseous pollutants emitted by them comply with
the standards as prescribed in this rule.
(2) Every manufacturer of an 279[agricultural tractor and construction equipment vehicle]
shall comply with the standards for visible pollutants, emitted by it, when tested as per
the procedure described in Indian Standards IS: 12062:1987.
(3) The emission of visible pollutants shall not exceed the limit values given below when
tested on engine dynamometer at eighty per cent load at six equally spaced speeds,
namely:—
(a) Fifty-five per cent of rated speed declared by the manufacturer or one
thousand r.p.m., whichever is higher; or
(b) rated speed declared by the manufacturer.
278 Inserted by G.S.R. 627(E), dated 8-9-1999 (w.e.f. 1-10-1999).
279 Substituted by G.S.R. 589(E), dated 16-9-2005, for the heading (w.e.f. 16-9-2005).
113
Maximum Smoke Density
Light absorption coefficient (lm) Hartridge units
3.25 75
(4) Every diesel driven 93280[construction equipment vehicles] shall be so manufactured
and produced by its manufacturer that it complies with the following standards of
gaseous pollutants, emitted by them in addition to those of visible pollutants as provided
in sub-rule (2) when tested as per the procedures described in ISO 8178-4 "CI" 8 mode
cycle, namely:—
The weighted average Mass of Carbon Monoxide (CO), Hydrocarbons (HC) and Mass
Oxides of Nitrogen (NOx) in gram or 281[per] kilo watt. lrr. emitted during the test shall not
exceed the limits given below, both for type approval and Conformity On Production
tests, namely:—
Mass of Carbon Monoxide (CO) — 14.0 grain or
281
[per] kilo watt. hr.
Mass of Hydrocarbon (HC) — 3.5 gram or
281
[per] kilo watt. hr.
Mass of Oxides of Nitrogen (NOx) — 18.0 gram or
281
[per] kilo watt, hr.]
282[(5) Every diesel driven agriculture tractor and power tiller shall be so manufactured
and produced by the manufacturer that it complies with the following standards of
gaseous pollutants emitted by them in addition to those of visible pollutants as provided
in sub-rule (2) when tested as per the procedure prescribed in ISO 8178-4 "CI" 8 mode
cycle, namely:—
The weighted average Mass of Carbon Monoxide (CO), Hydrocarbon (HC) and Oxides
of Nitrogen (NOx) and Particulate Matter (PM) in gram per kilo watt hour emitted during
the test shall not exceed the limits given below in the Table for Type Approval (TA) and
Conformity of Production (COP) tests, namely:—
TABLE
Bharat (Term) Stage II norms Bharat (Term) Stage III norms
(1) (2) (3)
TA=COP TA=COP
Mass of Carbon Monoxide
(CO)
9.0 5.5
Mass of Hydrocarbons (HC) 15.0 9.5
Mass of Oxides of Nitrogen
(NOx)
Mass of Particulate Matter 1.0 0.8]
280 Substituted by G.S.R. 83(E), dated 5-2-2003, for "agricultural tractor and construction
equipment vehicle" (w.e.f. 1-6-2003).
281 Corrected by G.S.R. 800(E), dated 3-12-1999.
282 Sub-R. (5) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
114
(PM)
Notes.—
(l)The norms mentioned in column (2) of the said Table which are applicable for
agricultural tractor with effect from the 1st day of June, 2003, shall be applicable for
power tillers from the 1st day of October, 2006.
(2) The norms mentioned in column (3) of the said Table shall be applicable for
agricultural tractor with effect from the 1st day of October, 2005 and for power tillers from
the 1st day of April, 2008.]
283[115-B. Mass emission standards for Compressed Natural Gas Driven Vehicles.—
284[Mass emission standards for vehicles when operating on Compressed Natural Gas
(hereinafter in this rule referred to as "CNG") shall be the same as are applicable for
gasoline vehicles with the exception that HC shall be replaced by Non-Methane
Hydrocarbon (NMHC), where NMHC = 0.3 x HC]
A. Original Equipment/Converted Gasoline Vehicles:
(1) For gasoline vehicles with Original Equipment (hereinafter in this rule referred to as
O.E.) fitment.—285[(a) In case of CNG fitments by vehicle manufacturers on new petrol
vehicles, each model manufactured by vehicle manufacturers shall be type approved as
per the prevailing mass emission norms as applicable for the category of new vehicles in
respect of the place of its use;]
Explanations.—In the case of O.E. or conversion of "In-Use" Gasoline Vehicles,—
(a) For the purposes of granting Type Approval to a CNG kit, the tests shall be carried
out as per the Table below by the test agencies.
TABLE
Test Reference Document
(1) (2)
(i)
(ii)
Mass emission tests
Engine performance tests on engine
dynamometer applicable for OE
only Constant speed fuel
consumption test
MOST/CMVR/TAP-115/116 and notifications issued by the
Government of India in this respect IS: 14599-1999
IS: 11921,1986 (for 4-wheelers)
IS: 10944,1983 (for mopeds)
IS: 10881,1984 (for motor cycles and scooters)
(b)The test procedure and safety guidelines for CNG vehicles, kit components including
installation thereof, shall be as per A1S 024, as amended from time to time, till such time
as corresponding BIS specifications are notified.
283 R. 115-B substituted by G.S.R. 853(E) dated 19-11-2001 (w.e.f. 19-5-2002).
284 Substituted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
285 CI. (a) substituted by G.S.R. 589(E),dated 16-9-2005 (w.e.f. 16-9-2006).
115
(c) For OE fitment and retrofitment on "in-use" vehicles, the responsibility to Type
Approval shall be that of the vehicle manufacturer and kit manufacturer or supplier
respectively.
(d) The Type Approval of CNG kit for "retrofitment" shall be valid for three years from the
date of issue of such approval and shall be renewable for three years at a time.
(e) The retrofitment of CNG kits on in-use vehicles shall be carried out by workshops
authorized by the kit manufacturer/supplier or vehicle manufacturers, as the case may
be.
(/) The test agency shall complete the test and give necessary certificate within a period
of three months from the date of receiving the kits.
(g)The kit manufacturer/supplier shall provide a layout plan for retrofitment of CNG kit in
the respective models on which any approved kit is to be installed, to the test agency for
vetting and approval. The retrofitment of the kit shall be on the basis of such approved
layout plan only. Testing agencies will be required to indicate specifically, the models
and their variants on which the certificate will be valid.
286[* * *]
B. O.E. CNG Vehicles/Converted Diesel Vehicle:
(I) For O.E. CNG Dedicated Vehicle (including drive-away chassis) made by vehicle
manufacturers.—287[(a) In case of CNG fitments by vehicle manufacturers on new diesel
vehicles, each model manufactured by vehicle manufacturers shall be type approved as
per the prevailing mass emission norms as applicable for the category of new vehicles in
respect of the place of its use;]
(b) O.E. CNG engine approved for specific engine capacity can be installed on the base
model and its variants complying with the requirements under these rules as applicable;
(c) Tests for particulate matter and emission of visible pollutants (smoke) under these
rules shall not be applicable;
(d) Prevailing COP procedure will also be applicable.
(II) For conversion by modification of engines of In-use Diesel Vehicles.— (A) Type
approval for diesel vehicle retrofitted/modified for dedicated CNG operation shall be
given for specific make and model of the vehicle, in view of major changes or
modifications involved in the CNG kit and diesel engine depending upon make and
model of the vehicle;
286 Item A, CI. (Ill) omitted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
287 CI. (a) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2006).
116
(b) CNG kit approved on the vehicle for specific engine capacity can be installed on the
base model and its variants fitted with the same capacity engine;
288[(c) The in-use vehicles when converted to operate on CNG shall meet the type
approval norms of diesel vehicles corresponding to the year of their manufacture subject
to the following minimum norms:—
(i) for the vehicles manufactured up to the 31st %day of March, 2000, the type approval
norms equivalent to India-2000 (India Stage I) norms as applicable under these rules;
(a) for the vehicles manufactured on and after the 1st day of April, 2000, the type
approval norms as specified in the Bharat Stage II norms, till the validity of such Bharat
Stage II norms;
(iii) for the vehicles manufactured on and after the 1st day of April, 2005, the type
approval norms as applicable subject to minimum of Bharat Stage III emission norms in
case of four-wheelers and Bharat Stage II emission norms for two and three-wheelers till
the validity of these norms;]
(d) Vehicles offered for Type Approval to the testing agency referred in rule 126 of the
Central Motor Vehicles Rules, 1989 shall have to comply with fitness requirement, as
applicable under these rules;
(e) Tests for particulate matter and emission of visible pollutants (smoke) under these
rules shall not be applicable;
(f) Separate Type Approval is required for mechanically controlled and electronically
controlled diesel fuel injected vehicles when retrofitted/ modified for CNG operation.
Explanations.—In the case of O.E. or conversion of "In-Use" vehicles by modification—
(a) for the purpose of granting Type Approval to the vehicle fitted with CNG engine
(converted from diesel engine) as O.E., or conversion by modification of "In-Use" diesel
vehicles, performance tests shall be carried out as per the Table given below by the test
agencies, namely:—
(1) (2)
(iv) Electro Magnetic
Interference (EMI)
In accordance with notification issued under rule 124 of Central Motor
Vehicles Rules, 1989
(v) Range test of at least 250 km for
buses
—
(vi) Cooling Performance IS: 14557,1998
(vii) Constant speed fuel consumption IS: 11921,1986 (for 4-wheelers)
IS: 10944,1983 (for mopeds)
IS: 10881,1984 (for motor cycles and scooters)
Explanation.—
288 CI. (c) substituted byG.S.R 589(E),dated 16-9-2005(w.e.f. 16-9-2006).
117
(a) Vehicles offered for Type Approval to the testing agency referred in rule 126 shall
have to comply with fitness requirement, as applicable under these rules.
(b)Test procedure and safety guidelines for such CNG vehicles, kit components
including installation thereof shall be as per A1S 024, as amended from time to time, till
such time as corresponding BIS specifications are notified.
(c) The test agency shall complete the test and give necessary certificate within three
months of the same being submitted for tests.
(d) Testing agencies will be required to indicate specifically, the models and their
variants on which the replacement of new engine will be valid.
D. Applicable Emission Norms
Category of Engines Applicable Emission Norms
(i) Fitted in vehicles with CVW equal to or less
than 3.5 ton
•For gasoline vehicles converted to CNG, Prevailing gasoline engine
norms for chassis dynamometer test
•For diesel vehicles converted to CNG, prevailing diesel engine norms
for chassis dynamometer lest
(ii') Fitted in vehicles with CVW greater than
3.5 ton
Prevailing diesel engine emission norms based on 13-mode steady-
state engine dynamometer test.
E. CNG vehicle/s kit components including installation shall comply the Safety Checks
as given in Annexure IX.
F. Testing agencies shall issue every Type Approval certificate containing the "Safety
and Procedural Requirements for Type Approval of CNG and LPC Operated Vehicles"
for CNG vehicles and conversion kits, as mentioned in Annexure X.
Note:—
1. For the purpose of these rules, "O.E. fitment" means the vehicles which are
manufactured for CNG operation by the vehicle manufacturer prior to their first
registration.
2. "Conversion of In-use Gasoline Vehicle" means a vehicle already registered as a
gasoline vehicle and is subsequently converted for operation on CNG by fitting the
conversion kit and carrying out the other necessary changes.
3. "O.E. CNG Dedicated Vehicles" means the vehicles which are manufactured for CNG
operation by the vehicle manufacturer prior to their first registration.
4. "Converted diesel vehicle" means a vehicle already registered as a diesel vehicle and
is subsequently converted for operation on CNG by modifying the diesel engine fitted on
that vehicle by fitting the conversion kit and carrying out the other necessary changes.
118
5. " Retro fitment" (or replacement) of diesel vehicle means a vehicle already registered
as a diesel vehicle and is subsequently converted for operation on CNG fitting a new
engine adapted to operate on CNG.
6. The AIS or IS specifications may be amended from time to time.
289[7. In case of conversion kits on in-use gasoline vehicles or converted diesel vehicles,
the validity of the type approval certificate issued by the testing agencies shall cover
vehicles manufactured between the year of manufacture of the vehicle, on which such kit
has been tested and date of the validity of the applicable norms prescribed for such
category of vehicles as per clause (a) of Item (II) of part A of rule 115-B. Testing
agencies shall be required to indicate specifically the model and their variants for diesel
vehicles and capacity range of gasoline vehicles on which the certificate shall be valid
for conversion.]
290[115-C Mass emission standards for Liquefied Petroleum Gas (hereinafter in this rule
referred to as LPG), driven vehicles.—291[(1) Mass emission standards for vehicles when
operating on Liquefied Petroleum Gas (hereinafter in this rule referred to as "LPG") shall
be same as are applicable for gasoline vehicles with the exception that HC shall be
replaced by Reactive Hydrocarbon (RHC), where RHC=0.5 x HC]
(2) For gasoline vehicles with Original Equipment (hereinafter in this rule referred to as
O.E.) Fitment,—
(a) In case of LPG fitment done by vehicle manufacturers on new petrol vehicles, each
model made by vehicle manufacturer shall be as type approved as per prevailing type
approval emission norms and these rules as applicable;
(b) base model and variants of such vehicle shall conform to these rules as applicable
and type approval emission norms in petrol mode as specified in these rules. In the case
of LPG mode, it shall meet mass emission norms as specified in rule 115 only excluding
crankcase and evaporative emission norms;
(c) a vehicle base model and its variants fitted with petrol tank of capacity not exceeding
5 litres, 3 litres and 2 litres on 4-wheeler, 3-wheeler and 2-wheeler respectively, shall be
exempted from mass emission tests, crankcase emission test and evaporative emission
test in petrol mode as specified in these rules, but shall comply with other provisions of
these rules as applicable;
289
Note 7 substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2006).
290
Inserted by G.S.R. 284(E), dated 24-4-2001 (w.e.f. 24-5-2001).
291
Substituted by G.S.R. 111(E), dated 10-2-2004 (w.e.f. 10-8-2004).
119
(d) such vehicle shall be capable of bi-fuel operation such as LPG and petrol;
(e) prevalent Conformity of Production (hereinafter in this rule referred to as the COP)
procedure shall also be applicable.
(3) For in-use gasoline vehicles,—
292 [(a) On and after expiry of one year from the date of publication of the Central Motor
Vehicles (Fifth Amendment) Rules, 2005 in the Official Gazette, the in-use vehicles fitted
with LPG kits shall meet the type approval emission norms specified in these rules for
gasoline vehicles as applicable to the corresponding year of manufacture of such
vehicle, subject to the following minimum norms:
(i) for the vehicles manufactured up to the 31st day of March, 2000, the type
approval norms equivalent to India-2000 (India Stage I) norms as applicable
under these rules;
(ii) for the vehicles manufactured after the 1st day of April, 2000, the type
approval norms as specified in the Bharat Stage II norms, till the validity of such
Bharat Stage II norms;
(iii) for the vehicles manufactured after the 1st day of April, 2005, the type
approval norms as applicable subject to minimum of Bharat Stage III emission
norms in case of four-wheelers and Bharat Stage II emission norms for two and
three-wheelers:
Provided that in respect of vehicle model/conversion kits/engine replacements type
approved and certified under rule 115-C prior to commencement of these rules (as per
notification number G.S.R. 284(E), dated the 24th April, 2001), such certificates shall
cease to be valid after one year from the date of publication of the Central Motor
Vehicles (Fifth Amendment) Rules, 2005, in the Official Gazette notwithstanding the
period of validity specified in such certificates. Such certificates need to be revalidated
by testing agencies in terms of these rules:
Provided further that respective kit manufacturer/retrofitter/converters shall be free to
obtain from testing agencies type approval in terms of new rules even prior to
commencement of these rules;]
(h) for purposes of LPG kit approval, kit manufacturer or supplier shall obtain the
certificate from any of the test agencies authorised under rule 126 based on capacity of
vehicle, in the following manner, namely:—
292 CI. (a) substituted by G.S.R. 589(E), dated 16-9-2005 (w.e.f. 16-9-2005).
120
(i) LPG kit for the vehicles shall be type approved for vehicles irrespective of make and
model based on engine capacity in cubic cm. Such a kit shall be considered fit for
retrofitment in any vehicle having engine capacity within a range of ± 25% tolerance;
(ii) for carbureted and Multi-point fuel injection fitted vehicles, separate type approval
shall be necessary.
(4)(a) For the purpose of granting type approval to LPG kit the following performance
tests shall be carried out by the test agencies:—
(i) Mass emission tests.
(ii) Engine performance tests.
(iil) Constant speed fuel consumption test;
(b) the tests specified under sub-clause (it) of clause (a) shall be carried out either on
engine dynamometer or chassis dynamometer as applicable under these rules.
However, in case of vehicle above 100 HP the tests shall be only on engine
dynamometer;
(c) the safety checks for such kit components including installation shall be as per the
norms and standards given in the Annexure VIII, apart from detailed test procedure or
safety guidelines contained in AIS 025 Dl, as approved by the Central Government from
time to time;
(d) for OE fitment and retro fitment on "in-use" vehicles, the responsibility of Type
Approval shall be that of the vehicle manufacturer and kit manufacturer or supplier,
respectively;
(e) the Type Approval of LPG kit for retrofitment shall be valid for three years from the
date of issue of such approval and shall be renewable for three years at a time;
(f) the retrofitment of LPG kits on in-use vehicles, shall be carried out by workshops
authorised by the kit manufacturer/kit supplier or vehicle manufacturers, as the case may
be;
(g) the test agency shall complete the test and give necessary certificate within a period
of three months from the date of receiving the kits;
(h) the kit supplier/manufacturer shall provide a layout plan for retrofitment of LPG kit in
the respective models on which any approved kit is to be installed, to the test agency for
vetting and approval. The retrofitment of the kit shall be on the basis of such approved
layout plan only.
121
293[* * *]
294[(6)For Diesel Vehicles with Original Equipment fitment.—295 [(/) In case of LPG
fitments by vehicles manufacturers on new diesel vehicles, each model manufactured by
vehicle manufacturers shall be type approved as per the prevailing mass emission
norms as applicable for the category of new vehicles in respect of the place of its use;]
(ii') O.E. fitment LPG engine approved for specific appropriate engine capacity can be
installed on the vehicle base model and its variants complying with the other
requirements under these rules as applicable;
(iii) Tests for particulate matter and emission of visible pollutants (smoke) under these
rules shall not be applicable; and
(iv) Prevailing COP procedures shall also be applicable;
(v) In case of limits for Hydrocarbons, the mass emission standards formula as specified
in sub-rule (1) shall be applicable.
Explanation.—In the case of O.E. fitment vehicles:—
(a) For the purpose of granting Type Approval to the vehicle manufactured by O.E., in
addition to the tests as specified in Central Motor Vehicles Rules, 1989, following
performance tests shall be carried out, as per the Table given below by the test agency,
namely:—
TABLE
SI. No. Test Reference Document (as amended from time to time)
(1) (2) (3)
1. Mass emission tests MOST/CMVR/TAP-115/116 and notification issued by the
Government of India in this respect
2. Engine performance tests IS: 14599-1999
3. Gradeability test In accordance with notification issued under rule 124 of Central Motor
Vehicles Rules, 1989
4. Constant speed fuel
consumption test
IS: 11921-1986 (for four-wheelers)
IS: 10944-1983 (for mopeds)
IS: 10881-1984 (for motor cycles and scooters)
AIS 054 (for three-wheelers)
5. Electro-Magnetic
Interference (EMI)
In accordance with notification issued under rule 124 of Central Motor
Vehicles Rules, 1989
6. Range test of at least 250
km for buses. For other
vehicle categories range
test to be carried out and
test results to be reported.
AIS 055
7. Cooling performance IS:14557-1998
293
Sub-rule (5) omitted by G.S.R. 589(E),dated 16-9-2005 (w.e.f. 16-9-2005).
294
Inserted by G.S.R 788(E), dated 27-11 -2002 (w.e.f. 2-6-2003).
295
. CI. (i) substituted by G.S.R.589(E),dated 16-9-2005(w.e.f. 16-9-2006).
122
Note:—The mass emission tests shall be carried out either on engine dynamometer or
chassis dynamometer, as applicable;
(b)Test procedure and safety guidelines for LPG vehicles, kit components including
installation thereof, shall be as per A IS 025, AIS 026, AIS 027 as amended from time to
time, till such time as corresponding BIS specifications are notified and shall be as given
in Annexure-VIII in addition to the detailed procedure of Safety Checks contained in AIS
025, AIS 026, AIS 027;
(c) For O.E. fitment manufactured vehicles, the responsibility of Type Approval shall be
that of the vehicle manufacturer;
(d) The test agency shall complete the test and give necessary certificate within a period
of three months from the date of receiving the kits.
296[(7) Replacement of In-use Diesel Engine by new LPG Engine.—For type approval of
in-use vehicle having diesel engine replaced by new Liquefied Petroleum Gas engine it
shall meet the prevailing emission norms as applicable to the category of vehicles in
respect of its place of use subject to the tests mentioned in the Table given below]:—
TABLE
SI. No. Test Reference Document (as amended from time to time)
(1) (2) (3)
1. Mass emission tests MCST/CMVR/TAP-115/116and notification issued by the
Government of India in this respect
2. Engine performance tests IS: 14599-1999
3. Gradeability test In accordance with notification issued under rule 124 of
Central Motor Vehicles Rules, 1989
4. Constant speed fuel consumption
test
IS: 11921-1986 (for four-wheelers)
IS: 10944-1983 (for mopeds)
IS: 10881-1984 (for motor cycles and scooters)
AIS 054 (for three-wheelers)
5. Electro-Magnetic Interference
(EMI)
In accordance with notification issued under rule 124 of
Central Motor Vehicles Rules, 1989
6. Range test of at least 250 km for
buses. For other vehicle categories
range test to be carried out and
test results to be reported.
AIS 055
7. Cooling performance IS: 14557-1998
Explanation.—(a) In case of in-use vehicles offered for Type Approval to the test agency
referred to in rule 126, it shall have to comply with fitness requirement, as applicable
under these rules and the said test agency may, if it thinks so, verify the same;
296 Sub-R. (7) substituted byG.S.R. 589(E),dated 16-9-2005 (w.e.f. 16-9-2006).
123
(b) In case of non-transport vehicles offered for retrofitment as per the tests mentioned in
the Table, it shall be the responsibility of the retrofitter to make necessary
inspection/checks regarding fitness of the such vehicles as applicable under these rules:
In the case of retrofitment of in-use transport vehicles offered for the tests mentioned in
the Table, the certificate of fitness granted under section 56 of the Act, shall be essential
before the vehicle is accepted for retro fitment/conversion;
(c) Test procedure and safety guidelines for such LPG vehicles, kit components
including installation thereof shall be as per AIS 025, as amended from time to time, till
such time as corresponding BIS specifications are notified and shall be as given in
Annexure VIII in addition to the detailed procedure or Safety checks contained in AIS
025;
(d) The test agency shall complete the test and give necessary certificate within a period
of three months from the date of the vehicle being submitted for tests; and
(c)The test agency shall be required to indicate specifically, the models and their
variants on which the replacement of new engine shall be valid.
(8) Applicable emission norms.—The emission norms as mentioned in column (3) of the
Table below excluding particulate matter shall be applicable to the corresponding
categories of engines as mentioned against them in column (2) of the said Table.
TABLE
SI. No. Category of Engines Applicable Emission Norms
(1) (2) (3)
1. Fitted in vehicles with G VW equal to or less
than 3.5 ton
• For gasoline vehicles converted to LPG,
prevailing gasoline engine norms for
chassis dynamometer test
• For diesel vehicles converted to LPG,
prevailing diesel engine norms for chassis
dynamometer test
2. Fitted in vehicles with G VW greater than 3.5
ton
• Prevailing diesel engine emission norms
based on 13-mode steady-state engine
dynamometer test
(9) LPG vehicle/kit components including installation shall comply with the Safety
Checks as given in Annexure VIII.
(10) The test agency shall, in addition to the Type Approval Certificate, issue Safety and
Procedural Requirements for Type Approval Certificate containing the Safety and
Procedural Requirements for Type Approval oi CNG and LPG Operated Vehicles, for
LPG vehicles and conversion kits, as mentioned in Annexure X.
Note:—For the purposes of these rules,—
124
(1) "OE fitment" means the vehicle engines which are manufactured for LPG operation
by the vehicle manufacturer prior to their first registration;
(2) "Conversion of In-use gasoline vehicle" means a vehicle already registered as a
gasoline vehicle and subsequently converted for operation on LPG by fitting the
conversion kit and carrying out the other necessary changes;
(3) "O.E. fitment LPG dedicated vehicle" means a vehicle which is manufactured for LPG
operation by the vehicle manufacturer prior to their first registration;
(4) "Type approval of In-use vehicle having diesel engine replaced by new LPG engine"
means a vehicle already registered as a diesel vehicle and is subsequently converted for
operation on LPG by fitting a new engine adapted for operation on LPG;
(5) The AIS or IS specifications may be as amended and notified from time to time.]
297[(6) In case of conversion kits on in-use gasoline vehicles or replacement of in-use
diesel engines by new LPG engines, the validity of the type approval certificates issued
by the testing agencies shall cover vehicles manufactured between the year of
manufacture of the vehicle, on which such kit had been tested and the date of validity of
the norms prescribed for such category of vehicles as per clause (a) of sub-rule (3) of
rule 115-C. Testing agencies shall be required to indicate specifically, the model and
their variants for diesel vehicles and capacity range of gasoline vehicles on which the
certificate shall be valid for conversion.]
Previous and next
← Rule 114Exhaust pipes of public service vehiclesRule 116 →Test for smoke emission level and carbon monoxide level for motor vehicles
All provisions of THE CENTRAL MOTOR VEHICLES RULES, 1989, (1-164)
Questions people ask
Is rule 115 of THE CENTRAL MOTOR VEHICLES RULES, 1989, (1-164) still in force?
No repeal of the CENTRAL MOTOR VEHICLES RULES, 1989, (1-164) is recorded.