S.O.2719 and S.O.2720 dated 28-11-2000-S (MILK PRODUCTS)
Notification - The Export (Quality Control and Inspection) Act, 1963
- Kind: Notification
- Under: The Export (Quality Control and Inspection) Act, 1963
Text of this notification
8014 THE GAZETTE OF INDIA : DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8015
MINISTRY OF COMMERCE AND INDUSTRY
(Department of Commerce)
ORDER
New Delhi, the 28th November, 2000
SO. 2719.—Whereas, for the development of the export
trade of India certain proposals for subjecting milk products
to Quality Control and Inspection prior to export, were pub-
lished as required by Sub-rule (2) of rule 11 of the Export
(Quality Control and Inspection) Rules 1964 in the Gazette
of India of Part II, Section 3, Sub-section on (ii) dated 6-5-2000
vide order No. S.O. 939 dated 19-4-2000 of the Government
of India in the Ministry of Commerce and Industry, Depart-
ment of Commerce;
2. And, whereas, the objections and suggestions were in-
vited, from all persons likely to be affected thereby, within a
period of forty five days of the copies of the said Gazette
were made available to the public on 11-5-2000.
3. And whereas, it is necessary to maintain the higher
quality standards and stipulate health requirements that would
encompass the standards prescribed in National/International
level;
4. And, whereas, health requirements should be laid down
for the production, storage and transport of milk products;
5. And, whereas, in particular, it is important that rules be
laid down governing the approval of establishments;
6. And, whereas, it is important also that the health require-
ments to be met by milk products be laid down;
7. And, whereas, it is the primarily responsibility of the
processors to ensure that Milk products meet the health
requirements laid down in this order;
8. And, whereas, the Competent Authority must by carrying
out Quality Control, Inspection and monitoring, to ensure
that processors comply with the above mentioned1 require-
ments;
9. And, whereas, the rules governing these Quality Control
Inspections and Monitoring must take account of the demands
of the international market;
10. And, whereas, a random check must be made to detect
the presence of residues of substances liable to be harmful to
human health;
11. And, whereas, provisions should therefore, be made as
a procedure for monitoring to ensure the above conditions
of equivalence with reference to the requirements of the
importing countries ;
12. And, whereas, Central Government nominated Compe-
tent Authority to ensure the effective compliance of the
quality standards in the country;
13. And, whereas, the Central Government has formulated
the proposals specified below for the said purpose and has
forwarded the same to the Export Inspection Council as
required by sub-rule (2) of the rule 11 of the Export
(Quality Control and Inspection Rules, 1964;
14. Now, therefore, in exercise of the powers conferred
by section 6 of the Export (Quality Control and Inspection)
Act, 1963 (22 of 1963). Central Government after consulting
the Export Inspection Council being of the opinion that it is
necessary and expedient to do so, for the development of the
export trade of India, hereby
(a) notifies that milk products shall be sujected to
quality control and inspection prior to export;
(b) specifies the type of quality control and inspection
in accordance with Export of milk products (Quality
control. Inspection and Monitoring) Rules 2000 as
the type of Quality Control, Inspection and Monitor-
ing which shall be applied to such milk products
prior to export;
(c) recognises the. specifications as set out in Schedule
appended to this order as the standard specifications
for milk products;
8016 THE GAZETTE OF INDIA: DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
(d) Prohibits the export of milk products by a unit in
the course of international trade unless it conforms
to the standards applicable to it and is accompanied
by a certificate stating that such unit is approved
and monitored by the Export Inspection agency esta-
blished under Section 7 of the Export (Quality
Control and Inspection) Act, 1963 (22 of 1963);
15. Nothing in this order shall apply to the export by land
or sea or air of bonafide samples of milk products to prospec-
tive buyers, the value of which shall not exceed permissible
limits as laid down in EXIM Policy from time to time and
where no such provisions exist the value limit of free sample(s)
shall not exceed Rs. 10,000.
16. In this order, milk products means :—Milk products
namely products exclusively derived from milk, it being ac-
cepted that substances necessary for their manufacture may
be added, provided that these substances are not- used to
relace in part or in whole any milk constituents, and com-
posite milk products of which not part replaces or is intended
to replace any milk, constituents and of which milk or a
milk products is an essential part either in terms of quantity
or for characterization of the product.
SCHEDULE
Specifications for Milk Products recognised as per Clause
(c) of section 6 of the export (Quality Control and Inspec-
tion) Act, 1963 shall be :
(a) National Standard of the importing countries o f
codex Standards of codex Alementeriours Com-
mission.
OR
(b) Contractual specifications agreed to between the
foreign buyer and the exporters provided the same
is not below the national standards.
(c) In the absence of (a) or (b) above, the National
Standard Specifications as notified shall apply.
(d) In case of any Milk Products for which no standard
is available at (a), (b) and (c) above, the standard
formulated for these products by the Standing Com-
mittee of the following members shall be made
applicable.
CHAIRMAN
1. Chairman, Agricultural and Processed
Food Products Export Development
Authority
2. Joint Commissioned (Dairy)
Department of Animal Husbandry
and Dairying,
Ministry of Agriculture
3. Deputy Commissioner (Dairy Development)
Ministry of Food Processing Industries
4. One representative of National Dairy
Development Board
5. Director
National Dairy Research Institute, Karnal
6. One representative of Dairy Association
of India
7. Representative of Export Inspection
Council
Chairman
Member
Member
Member
Member
Member
Member
[F. No. 6|l|2000-EI&EP]
P. K DAS, Director
8017
3299 GI/2000—2.
8018 THE GAZETTE OF INDIA : DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8019
8020 THE GAZETTE OF INDIA : DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8021
8022 THE GAZETTE OF INDIA: DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8023
8024 THE GAZETTE OF INDIA: DECEMBER 16, 2000/ AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8025
3299 GI/2000—3.
8026 THE GAZETTE OF INDIA : DECEMBER 16, 2000/ AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8027
8028 THE GAZETTE OF INDIA : DECEMBER 16,2000 AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8029
8030 THE GAZETTE OF INDIA : DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
8031
New Delhi, the 28th November, 2000
S.O. 2720.—In exercise of the powers conferred by Section
17 of the Export (Quality Control and Inspection) Act, 1963
(22 of 1963) the Central Government hereby makes the
following rules, namely:
1. Short title and Commencement.—(a) These rules may
be called the Export of Milk Products (Quality Control, Ins-
pection and Monitoring) Rules, 2000.
(b) They shall come into force on the date of their publi-
cation in the Official Gazette.
2, Definition.—In this notification unless the context other-
wise requires, the following definitions shall be applicable :
(a) "Act" means the Export (Quality Control and Ins-
pection) Act, 1963 (22 of 1963);
(b) "Agency" means any one of the Export Inspection
Agencies at Mumbai, Calcutta, Cochin, Delhi and
Madras established under section 7 of the Act.
(c) "Batch" means a quantity of milk products which
have been prepared under the same conditions and
in particular treated in single continuous operation:
(d) "Certificate" means certificate issued under sub-
section (3) of Section 7 of the Act stating that the
commodity conforms to the conditions regarding
Quality Control and Inspection;
(e) "Collection Centre" means an establishment where
raw milk may be collected and possibly cooled and
filtered.
(f) "Competent Authority' means any one of the Export
Inspection Agencies at Bombay, Calcutta, Cochin,
Delhi and Madras established under section 7 and
Inspection of the Act.
(g) "Composite Milk Products" Composite Milk Product
is a product of which the milk, milk products or
milk constituents are an essential part either in term
of quantity or for the characterisation of the
product:
Provided that the constituents not derived from milk are
not intended to tyke the place in part or in whole of any
milk constituent.
(h) "Consignment'' means a quantity of milk products
for a single delivery to one destination for further
processing by the food industry or intended for
direct human consumption;
(i) "Council" means the Export Inspection Council esta-
blished under section 3 of the Act;
(j) "Country of Despatch" means India;
(k) "Country of Destination" means the country to
which milk products are dispatched from India;
(1) "Heat Treatment" any treatment involving heating
that causes, immediately after it has been applied, a
negative reaction to the phosphates test.
(m) "Hermetically sealed container" means container
which, when sealed, is intended to protect the con-
tents against the entry of micro-organisms during and
after heat treatment and which is impervious;
(n) "Holding" means an establishment at which one or
more dairy animals and their followers are kept;
(o) "Milk Products" means Milk products, namely pro-
ducts exclusively derived from milk, it being accept-
ed that substances necessary for their manufacture
may be added, provided that these substances are not
used to replace in part or in whole any milk consti-
tuents, and composite milk products of which not
part replaces or is intended to replace any milk
constituents and of which milk or a milk products
is an essential part either in terms of quantity of
for characterisation of the product.
(p) "packing" means the placing of milk products in any
form of package;
(q) Packaging" means the placing of one or more wrap-
ped or unwrapped products as in a container, as well
as the container itself;
(r) '"Placing on the market" means the stocking or
display with a view to sale, offering for sale, delivery
or any other manner of disposal with the exception
of retail sale, which must be subject to the checks
laid down by national rules to" retail business.
(s) "Plant" means any premises where milk products
are processed and manufactured.
(f) "Potable water" means water that has been approved
by State Health Authority or other Agency or Labo-
ratory acceptable to the Competent Authority as
safe for drinking and suitable for food processing
(u) "Raw Milk" means the milk products by secretion
of the nammary glands of one or more cows, ewes,
goafs or buffaloes, which has not been heated beyond
40°C or undergone any treatment that has an equi-
velent effect;
(v) "Thermisation" is a heat treatment applied to raw
milk aimed at reducing the number of organisms
in milk and permitting longer storage of the milk
prior to further processing. The heating conditions
are 62° to 65°C for 15 to 20 seconds. Thermized
milk must be phosphatase positive.
(w) Treatment establishment" means an establishment
or production holding where milk and/ot products
are treated, processed and packed;
(x) "UHT (Ultra High Temperature) Treatment" treat-
ment of milk or cream is a high-temperature /short-
time heat treatment aimed at producing a com-
mercially sterile product, which can be stored at
room temperature. The process aims to destroy all
microganisms; any residual microorganisms are
unlikely to cause spoilage under normal storage con-
ditions. UHT-treated milk and cream are packaged
aseptically into sterilized, hermetically sealed con-
tainers*. The total heat treatment is equivalent, in
terms of its effectiveness against heat-resistant spares,
to a minimum F° value of 3 mm.
8032 THE GAZETTE OF INDIA : DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART I I - S E C . 3(ii)]
the temperature for UHT treatment is in the range of
135 degree—150 degree C in combination with
appropriate holding times such as 140V for 2—3
seconds.
A hermetically sealed container is a container that is
designed and intended to be secure against the entry
of micro organisms.
(y) "Wrapping" is the protection of the products by the
use of an initial wrapping or initial container in
direct contact with the products concerned as well
as the initial wrapper or initial container itself;
3. BASIS OF COMPLIANCE :
(a) It shall be the responsbility of the processors to
ensure that the milk products intended for exports
are handled processed at all stages: of production,
storage and transported under proper hygienic con-
ditions so as to meet the health requirement laid
down under these rules and that the product eon-
forms to the specifications given in the order by the
Central Government under section 6 of the Act.
(b) The Competent Authority shall ensure that all the
processors comply with the requirement by regular
monitoring of the plant as per the control measures
proscribed in the Para of this part. For effective
monitoring of the scheme, Council shall issue neces-
sary instructions in this regard from time to time.
4. The Milk products for Export shall be subjected to the
following conditions :
4.1 Any statutory restriction imposed by any State/
Central Government with respect to commercial/en-
vironmental conservation measures from time to time
shall strictly be adhered.
4.2 They must have been obtained from milk of dairy
animals which meet the requirements given in item
1 to 4 of Annexure A.
4.3 They must contain only the permissible food addi-
tives/processing aids, other than milk, which are fit
for human consumption.
4.4 They must have been treated and prepared in an
approved plant which complies with Chapters I and
II, V and VI of the Annexure B and satisfy the
requirements of these rules.
4.5 They mast have been processed and/or manufac-
tured under hygienic conditions complying with
Items 2 and 5 of Annexure B from milk meeting
the requirements laid down in Annexure C.
4.6 They must have undergone a processing treatment
which enables them to meet inter alia the analyti-
cal specifications laid down in item 3 of the
Annexure C.
4.7 They must have undergone a health marking and
lavelling in accordance with item 5 of the Annex-
4.8 They must have been packed in accordance with
item 4 of Annexure C.
4.9 They must be stored and transported in accordance
with item 6 of the Aunexure C.
4.10 The period during which the milk products are fit
tor human consumption and storage shall be indi-
cated by the processor.
4.11 The results of the various checks and tests are re-
corded and kept for presentation to the competent
authority for a period of two years.
4.12 To detect any residues of substances having a phar-
mocological or hormonal action, and of antibiotics.
pesticides, detergents and other substances should
not be present in milk which might alter the sen-
sery characteristics of milk products or make their
consumption dangerous or harmful to human health.
4.13 If the milk products examined show traces of resi-
dues in excess of the permitted levels fixed, they
must not be allowed either for the manufacture of
foodstuffs or for direct human consumption.
4.14 Tests for residues must be carried out in accordance
with National/Internationally recognised methods.
4.15 Having satisfied itself that the plant meets the re-
quirements with regard to the nature of the activi-
ties if carries out, the competent authority shall ac-
cord approval to such plant for a period of one
year.
4.16 The Competent Authority may take the assistance
of a representative each from EIC, APEDA, Minis-
try of Food Processing Industries, National Dairy
Development Board, and representative of industry
and co-operatives and experts from National Dairy
Research Institute etc. in the matter of approval of
processing plants.
4.17 The competent authority shall draw up a list of the
approved plants, each of which have an official
number and the competent authority shall furnish
to appropriate authorities the list of approved plants
and sub?equent change thereof.
4.18 The inspection and monitoring of plant and pack-
aging centres shall be carried out regularly by the
competent authority, which shall at all times have
free access to all parts of the plants, in order to
ensure that these rules are being observed. The
health checks and supervision of production shall
be carried out as per the elements given in
Annexure D.
5. CERTIFICATION :
(a) On request from the plant, the competent authority
shall issue health certificate in the prescribed pro-
forma after satisfying itself that the milk products
are processed in approved processing plants having
valid approval number and after satisfying the
relevant requirement.
(b) The Competent Authority shall also issue vague certi-
ficates on request from the processor or exporter
after satisfying itself that the requirements of the
relevant standards are met;
6. FEE :
fa) A fee of Rs. 5.000 shall be paid by the processor
along with the application for approval of the milk
processing plant.
(b) A fee at the rate of 0.2 percent of F.O.B. value shall
be paid by the processor or exporter to the Com-
petent authority:
NOTE :
The 'amount of fee for each consignment payable by the
processor /exporter shall be rounded off to the nearest rupee
and, for this purpose, where such amount contains a part
of a rupee then if such a part is 50 paise or more, it shall
be increased to one rupee and, if such part is less than
50 paise, it shall be ignored.
7. Competent Authority shall take actions if the require-
ment cease to be met.
8. APPEAL :
8.1 Any person aggrieved by the
(i) Decision of the competent authority not according
the approval as per rule 4.15.
(ii) Refusal of competent authority to issue Veterinary
Health Certificate as per rub 5 of this notification;
(iii) Decision of the competent authority to denotify
processor /exporter as per rule 7 of this notification;
8.2 Any person aggrieved by the decision of the compe-
tent Authority may prefer an appeal within 10 days of
receipt of such decision to on Appellate Authority appoin-
ted by the Central Government;
8033
8.3 The Appellate Authority shall consist of five members
appointed for the purpose by the Central Government;
8.4 The appeal snail be disposed of within 15 days of its
receipt and its decisions shall be final.
ANNEXURE A
REQUIREMENTS RELATING TO THE ACCEPTANCE
OF RAW MILK AT TREATMENT AND/OR
PROCESSING ESTABLISHMENTS
1. ANIMAL HEALTH REQUIREMENTS FOR RAW
MILK
1.1 Raw milk shall originate from—
(i) animals which are apparently healthy and do not
show any visible symptoms of infectious disease
likely to be transferable to humans through milk;
(ii) dairy animals which do not give the milk of ab-
normal sensory characteristics;
(iii) dairy animals which do not show any under wound
likely to affect the milk quality;
(iv) animals which have been treated with antibiotics or
other veterinary drugs which can be transferred to
milk shall not be brought to the collection centre,
unless the retention period of drug following such
treatment has been inspected.
2. HYGIENE OF THE HOLDING
(1) Holding from which raw milk is coming shall be
maintained in such a way as to ensure—
(a) good conditions of housing, hygiene, cleanliness and
health of the animals; and
(b) satisfactory hygiene conditions for milking, hand-
ling, storing and cooling (where applicable).
(2) Premises where milking is performed or milk is
stored, handled or cooled must be so said and/
or constructed as to avoid all risk of contamina-
tion of the milk,
(3) All efforts shall be made to ensure proper cleanli-
ness and ventilation in the animal premises/shed
with proper sunlight. There shall be sufficient drai-
nage so as to avoid accumulation of filth.
(4X0 The animals shall be held in clean, dry environ-
ment,
(ii) On a regular basis, the manure and residual food
materials shall be heaped away from the animal
premises/shed.
(5) Animal shed shall be free flies.
(6) Milking of the animals shall be carried out in a clean
and as far as possible dry environment.
(7) Where milk producing animals are kept untethered
in the open, the holding must also have a milking
area adequately separated from the housing area.
(8) The isolation of animals which are infected or sus-
pected of being infected, the separation of animals
from the rest of the herd must be possible and
effective.
(9) Animals of all species must be kept away from
premises and sites where milk is stored, handled
or cooled.
(10) Animals on production holdings should as tar as
possible undergo inspections to ensure that the re-
quirements of Animal health are being complied
with.
(11) Production holdings shall be regular checked to
ensure that hygiene requirements are being complied
with. The frequency of these checks must take
account of the assessment of risk on the production
holding concerned. If the inspection show that
hygiene is inadequate, appropriate steps shall be
taken to improve the hygienic conditions.
3. HYGIENE IN MILKING, THE COLLECTION OF RAW
MILK AND ITS TRANSPORT FROM PRODUCTION
HOLDING TO THE COLLECTION CENTRED OR PRO-
CESSING ESTABLISHMENTS.
(1) Hygiene in Milking—Milking Equipments
(i) Milking equipment/stensils shall be made of cor-
rosion resistant metals with smooth surfaces and
wide mouths which are easy to clean and do not
affect the sensory quality of milk.
(ii) Milking utensil must have a lid or cover.
(iii) Milking utensils should be thoroughly washed by
detergent such as washing soda followed by rinsing
with potable water and preferably sun dried.
(2) Storage Condition at Farmer's level
(i) Milk shall be brought to the milk collection point
as soon as possible immediately after milking in
closed containers.
(ii) If the milk is not collected within four hours of
milking, it must be cooled to a temperature of 7°C
or lower in the case of two consecutive collections
or 4°C or lower in collection is not daily. While
the milk is being transported to the treatment and/
or processing establishment, its temperature must
not exceed 8°C.
(3) Hygienic Milking Practices
(a) Feeding
The feed and fodder for milking animals shall be
palatable, nutritious, safe and suitable for feeding
and shall not present a risk of transferring resi-
dues of fertilizers, toxins, etc.
(b) Vermins
Vermins shall be combated in such a way that it
does not result in residue, i.e., pesticides, insecti-
cides, toxins, etc. in milk.
(c) Hygienic Milking - . . .
Before milking, the udder as well as surrounding
area of the animals shall be properly cleaned with
water and dried. Animal shall be groomed pro-
perly and hair removed from the body, so that
the risk contamination of milk can be avoided.
Further, animals should be washed regularly.
Before every milk, a sample of milk from each
teat shall be checked for freedom of foul smell
and any visible abnormalities like blood, pus.
flakes, etc. Such milk shall not be used for
human consumption.
(4) Personal Hygiene
(i) Absolute cleanliness should be required of per-
sonnel of specifically—Milking should be carried
out under good personnel hygiene of the milker,
i.e., he/she should not be suffering from diseases,
especially cough and cold, should wear clean
clothes, wash hands properly and cut nails perio-
dically before milking.
For this purpose, suitable hand washing facilities
are required near the place of milking.
(ii) Precautions may be taken to ensure that persons
liable to contaminate raw milk shall not be allo-
wed to handle it.
(5) Production Hygjene
A suitable mechanism shall be established to pre-
vent water being added to raw milk.
(6) Milk Reception at Collection-cum-Chilling Centre
(a) Premises
Rooms in the milk collection centre must be clean
and risks of contamination may be reduced to the
minimum by providing satisfactory safeguards. Ade-
quate provision must be made for cleaning and
sterilisation of containers and utensils.
3299 GI|2000-4.
8034 THE GAZETTE OF INDIA : DECEMBER 1 6 , 2 0 0 0 / A G R A H A Y A N A 25, 1922 [PART II—SEC. 3(ii)]
Th floors of the rooms of the collection centre
may be constructed of concrete of other imper-
vious material so that it should be easily cleaned.
It shall be suitably inclined to hasten rapid drai-
nage of wash water.
The walls and ceilings of the rooms should have
a smooth non-absorbent surface so ,that they can
be efficiently cleaned. The building should be
well lighted and adequately ventilated.
The surroundings of the collection centre should
be maintained clean and free from any water logging.
Proper method should be employed for pest
control.
(b) Milk Collection Equipment
After every shift for milk collection, all milk col-
lection and testing equipment should be thoroughly
cleaned with detergent and cleaned water.
Cleaned, Sanitized, Empty milk cans provided by
the dairy should be properly rechecked and if re-
quired may be washed with detergent and clean hot
(c) Collection of Milk
Before collection each individual farmer's milk
should be examined for sensory test. At the time
of collection, a strainer or a cleaned cloth may be
used to remove any suspended particle in the milk.
The collection time at the centre be fixed as per
the lorry /tanker timing of the processing plant.
As far as possible milk cans should be filled comp-
l e t e l y and the lid firmly placed on the can before
using another can. This will increase the shelf
life of milk, reduce the fat separation and also the
risk of contamination during transportation.
(d) Despatch of Milk and Chilling
Milk should be despatched to dairy plants in such
a manner that the interval between milking and the
arrival at the processing plant does not, exceed four
hours, depending upon the local climatic conditions.
In case the distance between the processing plant
and collection centre is large, then milk should be
entitled to 100C or below before despatch to the
processing plant. Cleanliness of the milk-cooling
equipment should be ensured. Further, the bulk
coolers should be provided with metal shields for
protection from air contamination.
(7) Transportation of Milk from the Farm and Villages
to the Collection-cum-Chilling centres and processing
plants
During transportation of milk in cans from the farm
and villages to the collection centre, adequate pre-
cautions should be taken en rote to ensure that the
deterioration in quality of milk is minimised.
Cans should have close fitting lids The filled cans
should be adequately protected from sunshine. Rain
or dirt should not be allowed to come in contact
with the inner portion of the can. No packing such
as jute,newspaper; straw etc. between can lids and
the can neck should be used.
Water from dripping vegetation or splashes on the
road should not be allowed to come in contact with
cans.
No other material should be loaded on the same
. vehicle which carries milk cans.
When road or rail tankers are used to carry milk,
they should be so designed that, as far as possible,
agitation is prevented during transport.
All the hygienic practices for preservation of milk
should be borne in mind while using the tanker
system for transporting milk.
The edge of the manhole in the tanker should be
flanged upwards so as to prevent dripping into the
tank when lid is lifted. A special cover has to be
provided over the lid for protection from dust or
dirt from the road. Similarly, a cover should be
provided over any valve or hose connector.
Tankers should be so constructed as to be easily
cleanable and the design of tankers should conform
to best technical and hygienic standards. The clean-
ing and sanitation of the tankers should be done at
the end of operations.
The insulation material should be of such quality
that the temperature of milk should not be allowed
to rise more than 2°C during transportation.
Violent agitation or surging in the tank should be
minimised to avoid breaking of bacterial clumps or
alteration of fat globules or admixture of air.
4. Raw Milk Standards
Raw milk collected for further processing shall con-
form to the following standards :
(a) Heavy Metals — The raw milk shall con-
form to the relevant
National/International
standards.
(b) Pesticides Residues —
(c) Aflatoxin —
(d) Antibiotic residues —
(e) Contaminants and
adulterants —
—Do—
— D o -
—Do—
—Do—
ANNEXURE B
1. GENERAL CONDITIONS FOR APPROVAL OF
TREATMENT ESTABLISHMENTS AND PROCESSING
ESTABLISHMENTS
The processing plant shall meet the following require-
ments :
(a) Site
. The processing plant/dairy shall preferably be situa-
ted in open, clean, and healthy surroundings away
from roadside where lot of dust arises due to vehi-
cular traffic : garbage dumps; cattle sheds; open
sewage drains o r other places likely to breed flies,
It shall be free from sources of obnoxious fumes,
smoke, odours or excessive dust. There shall not be
accumulation of fresh, garbage or similar waste in
the vicinity of the plant.
(b) Building
Structures housing the dairy shall be suitable in
size, construction and design to facilitate mainte-
nance and hygienic operations for processing
purposes. It should provide sufficient space for
housing of equipment and storage materials (raw
as well as finished products) necessary for hygienic
operations. The material of construction shall be
of brick, plaster, cement, concrete, tile or any
other equivalent materials which ensure cleanliness.
Construction of the building shall be such that it
shall be rodent proof, flyproof and birdproof. No
portion of building shall be used for domestic pur-
poses or other types of food operations unless
separated by suitable partitions or locations or
other effective means.
(c) Ventilation and Lighting
The processing plant/dairy shall be adequately
lighted and ventilated keeping in mind the number
of workers, their hours of work and nature of
operation. Ventilation and lighting shall also be in
accordance with Factory Act 1948.
(d) Floors, Walls, and Ceilings
The floor shall be smooth. washable properly sloped
to gullies connected to sewers or drains. It shall
be imprevious to water and not affected by weak
acids, alkalies or steam. Hard smooth and impervious
flooring such as cement concrete flooring
shall be made for fork room, store room and
8035
godown. Internal walls and ceilings shall be smooth
non-absorbent light-coloured surface, free from
crevices and sharp angles, to facilitate their efficient
cleaning. The junction of the floor with the walls
and junction between the two walls shall be rounded
to prevent accumulation of dust.
The dairy floors, walls and ceilings shall be regularly
cleaned.
(e) Repairs
The building shall be maintained in a proper state
of repair and cleanliness at all times. Whenever
required, it may be lime washed, pained, disinfected,
and deodorised.
(f) Processing Room
The room shall be made flyproof and rodent-proof.
The floor shall be impervious to water and shall
have a sufficient slope to ensure drainage. Drains in
processing rooms shall be cemented and covered
with detachable covers. Drains shall be kept clean
and shall be provide with traps at suitable places
before they are connected with the municipal drain
to avoid blocking or choking, or in the absence of
any such arrangement, they shall be drained in
soakage pits situated at a suitable distance from the
dairy and also the source of water supply. Adequate
facilities for washing the room shall be provided.
Adequate number of wash basins and sinks shall be
provided. Proper ventilation shall be maintained
to prevent condensation and drippage. Exhaust
fans «hall be provided where necessary.
The processing rooms shall be provided with effec-
tive means to prevent the entry of flies and insects.
Such effective means may be screens, fans, air cur-
tains, etc.The processing rooms should be provided
with self-closing double doors. The doors and win-
dows should be covered with flyproof wire gauge,
and they should be open outwards.
Effective drainage shall be provided to, drain off a
large quantity of water shed for washing the machi-
nery, equipment, furniture, floor etc ; 15 to 30 cm
half circular drains with glazed pipe at the bottom
should be provided. The slope of the floor should
be towards the drains ana the farthest end of the
floor from the drain should not be more than 5
meters. The drain openings should be provided
with screen traps to prevent solid matter from clogg-
ing the drains. The ends of the drains leading to
the outside of the factory should be made rodent
proof by providing screens. The screens shall be
examined periodically and replaced or cleaned, if
necessary. The drains should have water seals of
minimum 5 cm. At least 50 per cent of the length
of the drain should be covered ,to facilitate the
movement of trolleys. Mesh type for the drain
should be better to prevent habitation of cock-
roaches and rodents in closed areas of the drain.
Instruments and working equipment intended to
come into direct contact with raw materials and
products shall be made of corrosion-resistant mate-
rial and easy to clean and disinfect.
The processing plant shall have
— an appropriate number of changing rooms with
smooth, water proof, washable walls and floors, wash
basins and flush lavatories. The latter must not
open directly on to the work rooms. Wash basins
must be equipped for hand-washing and have
hygienic means of drying hands ; wash-basin taps
must not be hand operable ;
— a room or a cupboard secure place for the storage
of detergents, disinfectants and similar substances;
— a room or cupboard for storing, cleaning and
maintenance material;
— adequate facilities for cleaning and disinfecting
tanks used for transporting milk and liquid or
powdered milk-based products. However, such faci-
lities are not compulsory ,if there is a requirement
for the means of transport to be cleaned and disin-
fected in installations officially approved by the
competent authority.
2. GENERAL CONDITIONS OF HYGIENE IN TREAT-
MENT ESTABLISHMENTS AND PROCESSING ES-
TABLISHMENTS.
(a) General Dairy Hygiene
Waste and refuse shall be collected in covered
receptacles and shall not be allowed to scatter on
the floor of the unit. It should be disposed of in a
manner which is not detrimental to the hygiene of
the surroundings of the disposal.
Adequate measures shall be taken to prevent mould
growth on equipment and internal structures of pro-
cessing and storage rooms. Adequate steps shall be
taken to prevent infestation of cockroache, and
other household pests.
When pesticides are used, due care shall be exer-
cised to prevent contamination of equipment, raw
materials and packing materials. Under no circum-
stances shall these few used during processing.
Floors and drains shall be kept clean. On no
account shall the process room be used or con-
verted to a store room for raw materials or used as
eating room. Only the items required for processing on
a particular day shall be kept in the process room.
No lavatory, sink, cesspool or garbage shall be so
sitsated or maintained that odonrs or fumes there-
from pervade any room where the milk is stored or
processed. Power places shall be provided for sto-
rage of bdoms, brushes, buckets and other cleaning
gear.
The dairy effluents duly treated so as to confirm to
local statutory norms shall be disposed in a manner
which is not detrimental to the hygiene of the dairy
and its surroundings. The effluents shall not be let
off on road or in the open outside the dairy premises.
Window, glass and light fittings shall be maintained
clean and dust-free at all times.
There shall be no cobwebs in any part of the dairy
Birds and domestic animals shall not be allowed in
any part of the dairy.
All pumping and waste disposal lines should be
large enough to carry peak loads. All lines should
be watertight and the waste disposal should be
affected in such a manner as not to cause contami-
nation with potable water-supplies.
Premises should be well lit and ventilated. Special
attention should be given to equipment producing
excessive heat, steam, obnoxious fumes or vapours.
Good ventilation should be provided and mould
growth in overhead structures should be prevented.
Light bulbs and fixtures suspended above should be
of safety type.
(b) Plant and Equipment Hygiene
Material for equipment--All surfaces coming into
contact with the milk shall be smooth, free from
pits, crevices and loose scale and shall be non-absor-
bent. Furthermore, the surface shall be non-toxie
and unaffected by milk and cleaning compounds.
The finish of corrosion resistance (stainless steel,
etc. surfaces shall be smooth
All gasketing materials shall be food grade quality
and non-porous, non-absorbent. and fitted in a man-
ner such as to prevent its protruding into the milk
or creating recesses or ledges between the gasketed
joints which will interfere with proper cleaning.
(c) Installation of Equipment
All equipment shall be installed on a foundation of
durable, easily, cleanable material. Equipment shall
8036 THE GAZETTE OF INDIA: DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
be placed at least 45 cm from wall and ceiling, or
sealed water-tight thereto. All portions of the
equipment shall be installed sufficiently spaced
above the floor on a minimum number of support-
ing members to provide access for inspection and
cleaning, or be installed completely sealed (water-
tight) to the floor. Whenever equipment passes
through wall or floors, it shall be sealed thereto or
sufficient clearance shall be allowed to permit ins-
pection, cleaning and maintenance.
Where necessary, drains and catch pans shall be
provided. These shall be of such dimensions as to
collect all spill and drip, and readily accessible or
readily removable for cleaning. Where pipes pass
" through ceilings into the floor of the processing
area above, pipe sleeves shall be inserted in the
floor above so that their upper periphery is at least
5 cm above the floor.
All electrical connections, such as switch boxes, con-
trol boxes, conduit and cables, shall be installed at
least 45 cm away from the equipment walls to faci-
litate, cleaning, or be completely sealed to the equip-
ment or wall.
All equipment coming into contact with milk shall
be kept clean. An ample supply of steam and
water, hose, brushes, detergents and other equipment
necessary for the proper cleaning of machinery and
equipment shall be available. All equipment should
be cleaned and sanitised. All parts of equipments
coming into contact with milk shall be sterilized by
steam or any other suitable sterilizing agent after
each processing run. The entire processing system
shall be cleaned at the close of operation and flushed
out with potable water prior to use. Contaminating
stores and spare parts of machinery shall be kept
separate from the processing areas.
Bottles, pails, cans and other containers used to
transport or store milk shall be kept clean and not
used! for any other purpose.
It shall be ensured that containers for milk are kept
clean. The containers shall not be stacked in a
manner which allows the contamination of the
product.
(d) Water supply-
There shall be an adequate supply of safe and pot-
able water. Running water under pressure shall be
easily accessible to all rooms and areas in which
milk is handled and equipment were washed. The
equipment shall be so installed and used that back
siphonage of liquid into the potable water lines is
precluded.
Hot and cold water in ample supply shall be provid-
ed for plant clean-up needs where necessary. The
storage tanks for water should, unless completely
sealed, be kept covered with tight fitting lids, exa-
mined regularly and cleaned out at least once every
six months. The date of the last cleaning and
next cleaning shall be prominently displayed on the
storage tanks. The water shall be periodically exa-
mined as desired by the licensing authority chemi-
cally and bacteriologically. A record of such exa-
mination shall be maintained.
EMPLOYEE HYGIENE
Every person employed in connection with production
handling, processing and distribution of milk shall be medi-
cally examined by an authorised registered medical practi-
tioner and the examination shall include X-Ray of the chest
for tuberculosis. The examination shall also include, exa-
mination of stool for protozoal and helminthic infestation
for those parasites which are transmitted by ingestion and
for the presence of Salmonella, Shigella species and Vibrio
colerae; urine and blood examination for veneral diseases
Subsequently, the employee shall be medically examined once
in a year or more frequently; if necessary, to ensure that
he/she is medically fit and free from communicable diseases.
A record of such examination shall fie maintained.
It shall be impressed on all employees that they should
notify to the medical officer or management, cases of fever,
vomiting, diarrhoea, typhoid, dysentery, boils, cuts and sores
and ulcers (however small), discharging ears and notifiable
diseases occurring in their own homes and families.
No worker who is suspected to be suffering from any of
the disorders listed above shall be permitted to work inside
the dairy. The supervisor shall check the personal hygiene
of the workers before the start of work and whenever they
enter any processing groom after any absence.
Employees shall keep their finger nails short and clean and
wash their hands with soap or detergent and water before
commencing work and after each absence, specially after
using sanitary conveniences. Towels used for drying hands
should be clean. No worker shall allow his hands or any
part of his body or clothing to come in contact with the
milk. He should adopt strict hygienic practices so as to
avoid adding any microbial contamination to the milk.
All employess shall be inoculated and vaccinated against
the enteric groups of diseases once a year and against small
pox once in two years. In case of an epidemic all workers
shall be inoculated. A record shall be maintained. No
worker shall be allowed to work without proper clothing
and foot wear.
Employees shall be provided with clean uniforms (prefer-
ably white) or aprons or both and clean washable caps,
wherever necessary. Separate room or place for changing
the clothes shall be provided. The clothes shall not be hung
in any processing room. The uniforms shall not be
hung in any processing room. The uniforms shall not be
worn outside the dairy but put on just before starting the
work and changed when leaving.
Eating, spitting, nose cleaning or the use of tobacco in
any form including smoking or chewing betel leaves shall
be prohibited within the processing, packing and storage area
of the dairy. Notice to this effect shall be prominently dis-
played and enforced.
Sufficient and suitable sanitary conveniences shall be pro-
vided, maintained and kept clean. The conveniences shall
be properly lighted. Separate conveniences shall be provid-
ed for each sex. No convenience shall open directly into
any work room in the dairy. The conveniences shall always
be maintained! clean and in good repairs.
Sufficient number of wash basins with adequate provision
of nail brushes, soap and towels, latrines and urinals in the
prescribed manner should be provided, conveniently situated
and accessible to workers at all times while they are the
dairy. The wash basins shall be installed in or alongside
the sanitary conveniences.
The importance of hygienic and aesthetic standards should
be inculcated to the personnel, since carelessness at any stage
will endanger the health of the conumers.
3. Special Requirements for registration of collection cen-
tres—In addition to the general requirements laid down at
item 1 above, the collection centres must have at least:
(i) cooling facilities if milk is stored at the collection
centre.
(ii) Testing facilities to check fat and SNF content. These
should include milk testing equipment.
(iii) Milk collection equipment which should be properly
sanitized.
4. Special requirements for the approval of Treatment
Establishments and Processing Establishments.—In addition
to the general requirements laid down in 1 above, treatment
establishments and processing establishment must have at
least:
(i) equipment for the cooling and cold storage of heat-
treated milk, liquid milk-based products. Cold
Stores must be equipped with correctly calibrated
temperature measuring appartus.;
»
(ii) — in the case of wrapping in disposable containers,
an area for the storage of such containers and for
storage of the raw materials intended for their
manufacture, '
8037
—. in the case of wrapping in re-usable containers, a
special area for their storage and equipment design-
ed to clean and disinfect them mechanically;
(iii) containers for storing raw milk, standardization equip-
ment and containers for storing standardized milk,
(iv) if appropriate, centrifuges or any other suitable means
for removal of extraneous matters from milk;
(v) heat-treatment equipment fitted with :
— an automatic temperature control,
— a recording thermometer,
— an automatic safety device preventing insufficient
heating, or cooling medium, and
— an adequate safety system preventing the mixture
of pasteurized or sterilized milk with incompletely
heated milk, and!
— a recording device for the safety system referred
to in the preceding indent;
(vi) equipment for the cooling, packing and storage of
frozen milk products if such operations are carried
out there;
(vii) equipment for drying and packing powdered milk
products if such operation are carried out there.
5. Hygiene requirements relating to the premises equip-
ment and staff of Treatment Establishments and Processing
Establishments.—In addition to the general requirements laid
down above establishments must comply with the following
conditions:
(i) Closs-contamination between operations by equip-
ment, ventilation or staff must be avoided. If ap-
propriate, and in the light of the assessment of risk,
rooms intended for production processes shall be
divided into wet and dry areas, each having its own
operating conditions.
(ii) As soon as possible after each journey, or after each
series of journeys where there is only a very short
space of time between unloading and the following
loading, but in any event at least once each work-
ing day, containers and tanks used for transporting
raw milk to the milk collection or standardization
centre or to the milk treatment or processing estab-
lishments must be cleaned and disinfected before
reused.
(iii) Equipment, containers and installations which come
into contact with milk or milk-based products or
other perishable raw materials during production
must be cleaned and disinfected at the end of each
work phase and at least once each working day.
(iv) The treatment premises should, if necessary, be clean-
ed at least once each working day.
(v) For the cleaning of other equipment, continers and
installations which come into contact with microbio-
logically stable milk-based products and with rooms
in which such substances are placed, the operator
or manager of the establishment shall draw up a
cleaning programme based on the assessment of
risk. The programme must meet the requirement
. . referred to in item 1 and must also ensure that
the product does not become unsafe and a health
risk to the consumer as a result of inadequate clean-
ing' methods.
ANNEXURE C
1. REQUIREMENTS FOR MILK FOR THE MANUFAC-
TURE OF MILK PRODUCTS
(i) The operator or manager of the processing establish-
ment must take all necessary steps to ensure that
the raw milk is treated (within 36 hours of accep-
tance), if the milk is kept at a temperature not ex-
ceeding 6°C, or within 48 hours of acceptance if
the milk is kept at a temperature of 4°C or lower.
(ii) Heat-treated milk intended for the manufacture of
milk products must be obtained from raw milk,
which complies with the standards, laid down in
Annex A.
(iii) Heat-treated milk must meet the following require-
ments:
(a) pasteurized milk must comply with Clause 2(a) of
this Annex.
(b) UHT milk must have been obtained by the treat-
ment as defined under the item on definition and
shall comply with the requirements given therein.
2. MILK PROCESSING
Prior to processing, raw milk shall be filtered or clarified
to remove visible dirt and any other foreign material in it.
The milk may be homogenized before pasteurization at appro-
priate pressure.
After completion of the day's run, the part of the homoge-
nizer shall be dismantled and thoroughly washed with deter-
gent solution followed by rinsing with hot water. Before
using fresh batch of milk, the homogenizer shall be sterilized
by pumping through it hot water or chlorine solution. The
piston packing and leather gaskets of the homogeniser when
worn out, shall be replaced as early as possible.
(a) Pasteurisation:
The milk shall be heated to at least 66°C and held at
66°C continuously for at least 30 minutes, or it shall be
heated to at least 74°C and held at 74°C conti-
nuously for at least 15 seconds in a standard and properly
operated equipment. Other temperature and time combina-
tions that enable the pasteurised milk to meet the hygienic re-
quirements may also be adopted after approval by competent
authority. To ensure that the bacteria present in the form are
killed, space heaters should be provided. The clear posi-
tioning and accuracy of the indicating and recording thermo-
meters shall be checked regularly. The long stemindicating
thermometer shall be accurate within +0.5°C. The re
cording thermometer shall be accurate within 1°C between
63 and 64o C for holder pasteurization and within 1°C and
between 71 °C and 72°C for high temperature short time
(HTST) pasteurization.
After holding the milk, it should be cooled immediately in
the standard and properly operated equipment to a tempera-
ture not exceeding 5°C. The pasteurized milk should be
maintained at a temperature not exceeding 7°C until it leaves
the milk plant for distribution.
All parts of the pasteurizer should be kept in a hygienic
condition. Appropriate type of detergentsanitizers which do
not adversely affect the quality of molk should be used for
effective cleanliness and sterility of the pasteurization plant.
The rubber gaskets of the pasteurizer need special attention
in regard to cleaning operations because of the deposition of
milk residues. All possible precautions shall be taken to
avoid recontamination of raw milk after pasteurization through
improperly designed or leaky equipment pumps, dirty bottles
and bottling equipment, contaminated water, dust flies and
from dirty habits of dairy plant personnel.
Pasteurized milk shall be filled in suitable package of
standard quality. The package shall be so shaped as to
permit effective cleaning operation. The package should not
have inaccessible corners where milk deposits or scales are
likely to accumulate or difficult to clean. The returned
empty package shall be appropriatley cleaned and sanitised
using suitable detergent and sanitizer.
(b) Laboratory Control
The control dairy laboratory plays a vital role in check-
ing the efficiency of milk processing. A well-equipped labo-
ratory with competent quality control staff is essential for an
efficient operation of milk processing plant. Depending upon
the quantity of milk handled by each dairy, appropriate lay-
out plant may be formulated.
(c) Milk Products
All the milk products manufactured in the processing plants
should conform to the hygienic requirements outlined above.
Wherever applicable the milk products should also conform
to the national/international standards.
8038 THE GAZETTE OF INDIA ; DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART I I - S E C 3(ii)]
3. MICROBIOLOGICAL CRITERIA FOR MILK
PRODUCTS:
A. Microbiological criteria for certain milk-based products
on removal from the processing establishments.
(i) Compulsory criteria : Pathogenic micro-organisms
Type of Micro-
organism
Linsteria mono-
cytogenes
—Salmonella spp
Shigella
Products
Cheese, other
than hard
cheese
other products
All milk pro-
ducts, except
Milk Powder.
Milk Powder
All milk pro-
ducts.
Standard
(ml, g)
Absent in 25 g
Absent in 1 g
Absent in 25 g
Absent in 25 g
Absent in 25 g .
In addition, pathogenic micro-organisms and their toxins
must not be present in quantities such as to affect the
health of consumers.
If these standards are exceeded, the foodstuffs must be ex-
cluded from human consumption and withdrawn from the
market.
Sampling programmes will- be drawn up in the light of
the nature of the products and the assessment of risk.
(ii) Analytical criteria : organisms indicating poor hygiene
Type of Micro-
organism
—Staphylococcus
aureus.
Escherichia coli
Products
Soft cheese
(made from
hea-treated
milk)
Fresh cheese
Frozen milk
products (in-
cluding ice-
cream).
Milk Powder
Other Dairy
Products
Soft Cheese and
. other dairy
products
Milk powder
Standard
(ml, g)
m = 100
M = 1000
n = 5
c = 2
m = 10
M = 100
n = 5
c = 2
Absent in 0.1/g
Less than 100/g
m = 100
M = 1 000
n = 5
c = 2
Absent in 0.1 g
In all cases where these standards are exceeded there must
be a review of the implementation of the methods for moni-
toring and checking critical points applied in the processing
establishment. The competent authority shall be, informed
of the corrective procedures included in the production moni-
toring system to prevent any repetition of the occurrence.
If strains of enterotoxinogenic Staphylococcus aureus or
strains of Escherichia coli that are presumed to be pathogenic
are identified, all the batches involved shall be withdrawn
from the market. In this case the competent authority snail
be informed of the findings and of the action taken to with-
draw the suspect batches and the corrective procedures in-
troduced into the production monitoring system.
(iii) Indicator organisms : guidelines
Type of Micro-
organism
Coliforms
Plate Count
Products
Liquid Milk
products
Butter Made
from Pasteu-
rized milk or
Cream.
Frozen milk
products (in-
cluding ice-
cream).
Milk powders
Other Dairy
Products.
Pasteurised
Milk.
Ice cream
Milk Powders
Standard
(ml, g)
m = 0
M = 5
n = 5
c = 2
m = 0
M = 10
n = 5
c = 2
m = 0
M = 10
n = 5
c = 2
Absent in 0.1 g
Less than 200/g
Less than 30,000/
ml.
Less than
2,50,000/ml
Less than
40,000/g.
These guidelines should help producers in ensuring proper
operation of their establishments and in implementing the
system and the procedure for carrying out their own check
on their production.
Where;
n=number of sample units, comprising the sample;
m=threshold value for the number of bacteria; the
result is considered satisfactory if the number of
bacterial in all sample units does not exceed 'm';
M=Maximum value for the number of bacteria; the
result is considered unsatisfactory if the number
of bacteria in one or more sample units is 'M' or
more;
c=number of sample units where the bacteria count
may be between 'm' and ',M' the same being consid-
ered, acceptable if the bacterial count of the
other sample units is 'm' or less.
4. WRAPPING AND PACKAGING
(i) Wrapping and packaging must take place under satis-
factory hygiene conditions in rooms provided for
that purpose.
(ii) Bottling, filling of containers with liquid milk pro-
ducts and sealing of containers and of packaging
must be carried out automatically.
(Hi) Wrapping or packaging may not be reused for the
products with the exception of certain types of con-
tainers which may be reused after thorough cleaning
and disinfecting.
8039
Sealing must be carried out in the treatment establish-
ment in which the heat treatment has been carried
out immediately after filling, by means of sealing
devices which ensure that the milk is protected from
any adverse effects of external origin on its charac-
teristics. The sealing system must be so designed
that once the container has been opened, the evi-
dence that it has been opened remains clear and
easy to check.
(iv) The operator and manager of the establishment must
ensure for control purposes, the following informa-
tion is visibly and legibly displayed on the packaging
of the milk products :
Milk Products made from pasteurized milk, the
temperature at which the products must be stored.
(v) Product manufacture and packaging operations may
take place in the same room, notwithstanding point
1, subject to the following conditions:
(a) The room must be sufficiently large and so equipped
that the hygiene of the operation is assured;
(b) The packaging material must have been brought to
the treatment or processing establishment in a
protective cover in which they were placed imme-
diately after manufacture and which protects them
from any damage during transport to the establish-
ment and must have been stored there under
hygiene conditions in a room intended for that
purpose.
(c) The rooms for storing the packaging material must
be free from dust and vermin and separated from
rooms containing substances which might con-
taminate the products. Packaging material must
not be placed directly on the floor;
(d) packaging material must be assembled under hygi-
enic conditions before being brought into the
room. A derogation from this requirement may
be granted in the case of the automatic assembly
of packaging provided there is no risk of con-
tamination of the products.
(e) packaging material must be brought into the room
under hygienic conditions and used without delay.
It may not be handled by staff handling un-
wrapped products;
(f) immediately after packaging, the products must be
placed in the storage rooms provided for the
purpose.
5. CONDITIONS GOVERNING HEALTH MARKING AND
LABELLING
A. Conditions governing health marking
(i) In case the importing country requires health certi-
ficate or health mark on the label, the same may be
provided. Health marking must be carried out
during or immediately after manufacture in the
establishment, in an easily visible place. The mark
shall be legible, indelible and its characters easily
distinguishable. The health mark may be applied
to the product or to the wrapping, if the product
is individually wrapped, or to a lable affixed to this
wrapping. However, where a product is individually
wrapped and packaged, it will suffice for the health
mark to be applied to the packaging.
(ii) Where products marked in accordance with point 1
are subsequently placed in a packaging, the health
mark must also be applied to the packaging.
(iii) (a) The health mark shall give the following parti-
culars;
— the name of the consigning country in
capital's,
— the approval number of the
establishment
(b) the health mark may be applied to the product,
wrapping or packaging by an ink stamp or by
branding, or it may be printed on or applied to a
label. In the case of products in hermetically-
sealed containers, the mark must be indelibly
applied either to the lid or to the container;
(c)' the health mark may also consist of an irremovable
plate of resistant material complying with all the
hygiene requirements and bearing the information
specified in (a).
B. Conditions governing labelling
The labelling for milk products must clearly show for ins-
pection purposes:
1. the nature of any heat treatment applied at the end
of the manufacturing process:
2. for milk products in which growth of micro-organisms
can occur, the use by or minimum durability date
along with storage condition.
6. STORAGE AND TRANSPORT REQUIREMENTS
(j) Products which cannot be stored at ambient tempera-
ture must be stored at the temperatures established
by the manufacturer to ensure their durability. In
particular, the maximum temperature at which pas-
teurized milk may be kept until it leaves the estab-
lishment and during transport must be 6oC. When
stored under cooled conditions the- storage tempera-
tures must be registered and the cooling rate must
he such that the product reaches the required tem-
perature as quickly as possible.
(ii) Tanks, cans and other containers which are used for
the transport of pasteurized milk must comply with
all the rules of hygiene and in particular the
following:
— their inside surfaces and any other part which may
come into contact with the milk must be made
of SS 304 smooth material which is easy to wash,
clean and disinfect, resists corrosion and does not
transfer substances to the milk in such quantities
as to endanger human health impair the compo-
sition of the milk or adversely affect its sensory
characteristics.
they must designed so that the milk can drain away
completely; if they are fitted with taps, these must
be easy to remove, dismantle, wash, clean and
disinfect;
— they must he washed, cleaned and disinfected imme-
diately after each use and as necessary before
further use;
— they must be hermetically sealed before and during
transport by means of a watertight sealing device.
(iii) Vehicles and containers used for transporting pasteu-
rized milk must be designed and equipped in such
a way that the required temperature can be main-
tained throughout the period of transport.
Civ) Vehicles used for transporting heat-treated drinking
milk and milk in small containers or in churns must
be in good condition. They may not be used to
transport any other product or object likely to cause
the milk to deteriorate. Their internal surface must
be smooth and easy to wash, clean and disinfect.
The interiors of vehicles intended for transporting
milk must comply with all the rules of hygiene.
Vehicles intended for the transport of heat-treated
milk in small containers or churns must be so
designed as to give the containers or churns ade-
quate protection against all contamination and at-
mospheric influences and may not be used to trans-
port animals.
(v) To that end, the competent authority must regularly
check that the means of transport and loading con-
ditions meet the hygienic requirements.
8040 THE GAZETTE OF INDIA: DECEMBER 16, 2000/AGRAHAYANA 25, 1922 [PART II—SEC. 3(ii)]
(vi) The products covered by this order must be dis-
patched in such a way that they are protected from
anything liable to contaminate them or to cause
them to deteriorate, having regard to the duration
and conditions of transport and the means of trans-
port employed.
ANNEXURE—D
I. HEALTH CHECKS AND SUPERVISION OF PRO-
DUCTION
(i) Establishments shall be subject to supervision by the
competent authority, which must ensure that the
requirements of this Order are met and in parti-
cular;
(a) check
(0 the cleanliness of the premises and equipment
and staff hygiene;
(ii) the efficacy of the checks carried out by the
establishment, notably by examining the results
and taking samples;
(iii) the microbiological and hygienic conditions of
the milk-based products;
(iv) the efficacy of the treatment of the milk-
based products;
(v) the hermetically sealed containers by means of
random sampling;
(vi) the appropriate health marking of the milk-based
products whenever applicable;
(vii) storage and transport conditions;
(b) take any samules required for laboratory tests:
(c) make any other checks it considers necessary to
ensure compliance with this Order.
(ii) The Competent Authority must have free access at
all time to the cold stores and all working premi-
ses to check that these provisions are being strictly
complied with.
[F. No. 6/1/2000-EI&EP]
P. K. DAS, Director
All of The Export (Quality Control and Inspection) Act, 1963